Installation Guide

ManualsBrandsDelaney ManualsResidential LeversDelaney SandCast Collection Ronda Series Passage Door Lever Set with Curved Rosette

Table Of Contents

INSTALLATION INSTRUCTIONS FOR SOLID BRASS KNOB & LEVERSET

1. ADJUSTABLE LATCH FOR 2-3/8" (60mm) AND 2-3/4" (70mm) BACKSET

D. To reset 2-3/8" (60mm) backset

just push spindle cam to left

edge of adjusting hole.

NOTE :

Be sure to keep spindle cam square

in correct position as illustrated

before push spindle cam to left.

Otherwise you will have difficulty in

pushing spindle cam to left.

The models are supplied with adjustable latch which can fit 2-3/8" or 2-3/4"

(60mm or 70mm) backset.

Adjustable latch was preset at factory for a 2-3/8" (60mm) backset.

If a 2-3/4" (70mm) backset is required, please adjust as shown below.

A. This latch is for 2-3/8"

(60mm) backset.

B. Pull spindle cam all the way

to right edge of adjusting

hole.

C. Be sure 2-3/4" (70mm)

stem hole is proper aligned.

Your latch is now set for a

2-3/4" (70mm) backset.

A B C

PULL

PUSH

(A)

(B)

2. DETERMINE HANDING OF YOUR DOOR

Stand at exterior side and face to yourdoor.

A. Your door is left hand door if hinges were installed

at your left hand.

B. Your door is right hand door if hinges were installed

at your right hand.

EXTERIOR

LEFT HAND DOOR RIGHT HAND DOOR

HINGES HINGES

Backset is a distance from door edge to center of hole on door face.

The locks are supplied with adjustable latch which can fit 2-3/8" (60mm) or 2-3/4" (70mm) backset.

Just follow the steps shown below to change backset.

3. MARK DOOR

Select 2-3/8" or 2-3/4" (60mm or 70mm)

backset as desired and mark center of

hole on door face.

4. DRILL HOLES

Drill 2-1/8" (54mm) hole on door face,

from both sides to avoid wood splitting.

Drill 1" (25.4mm)hole for latch.

A. Insert latch in hole and keep it parallel to door face.

Mark outline of face plate and remove latch.

B. Chisel 5/32" (4mm) deep or until face plate flush with door

edge.

C. Insert latch and tighten screw.

A. Close door until latchbolt touches jamb to locate strike in jamb and center

line of strike. Open door and extend line from mark to door stop.

Measure on half of door thickness from door stop and vertically mark drill point

center for strike.

B. Drill 1"(25.4mm) hole 1/2"(13mm) deep in door jamb on drill point for strike.

C. Match screw holes on strike with center line on jamb.

Outline outside edge of strike. Chisel 1/16"(1.6mm) deep for strike.

D. Adjustable tang on strike permits bending in or out to eliminate too loose fit

between door and door stop.

5. INSTALL LATCH

6. INSTALL STRIKE

AD1

A B

FOR USE ON DOORS 1-3/8" TO 1-3/4" (35mm~45mm)THICKNESS

Summary of content (2 pages)

PAGE 1
AD1 AD1 INSTALLATION INSTRUCTIONS FOR SOLID BRASS KNOB & LEVERSET FOR USE ON DOORS 1-3/8" TO 1-3/4" ( 35mm~45mm) THICKNESS 1. ADJUSTABLE LATCH FOR 2-3/8" (60mm) AND 2-3/4" (70mm) BACKSET Backset is a distance from door edge to center of hole on door face. The locks are supplied with adjustable latch which can fit 2-3/8" (60mm) or 2-3/4" (70mm) backset. Just follow the steps shown below to change backset.
PAGE 2
AD1 AD1 7. CHANGE HANDING OF CURVED LEVER A. Use wrench furnished to turn loose set screw. B. Pull out and changs side of interior lever and exterior lever. C. Assemble both levers again. NOTE: Be sure to have set screw face downward. (A) (B) (C) SET SCREW FACE DOWNWARD WRENCH 8. INSTALL PRIVACY LEVERSET 9. INSTALL PASSAGE LEVERSET Privacy leverset is for bed/ bathroom doors. Push button on inside rose to lock both levers.