Self-contained compact work top freezers Specification Sheet

The Delfield Company, 980 S. Isabella Rd., Mt. Pleasant, MI 48858, U.S.A. • (800) 733-8821 • Fax (800) 669-0619 • www.delfield.com

PROJECT

ITEM #

QUANTITY DATE

APPROVAL

403

Self-contained compact work top freezers

The refrigeration system on this

equipment uses HFC--404A refrigerant.

Short form specications

Exterior top shall be one-piece, 22-gauge stainless steel with front edge turned down

to form nosing and rear edge turned up to form a 2" (5.1 cm) thick by 4" (10.2 cm) high

backsplash.

Exterior back and bottom shall be one-piece 24-gauge galvanized metal. Exterior ends

shall be 22-gauge stainless steel.

Base interior shall be one-piece thermoformed ABS plastic material, with integral shelf

supports. Base shall be fully insulated with high-density foamed-in-place polyurethane.

Refrigeration system shall use HFC-404A refrigerant. Compressor shall be ¢ h.p., with

condenser coil and hot gas condensate evaporator mounted on rear of cabinet. Evapora-

tor coil and temperature control shall be mounted on the interior rear wall of the cabinet.

Refrigerant ow shall be controlled by a capillary tube. Cabinet shall maintain

–5°F to 0°F (–21°C to –18°C) interior cabinet temperature.

Electrical connections shall be 115 volt, 60 Hertz, single phase. Unit shall have a 7' (2.1

m) long electrical cord and NEMA 5-15P plug. Cord and plug shall be located on rear of

cabinet, centered left to right, 16" (40.6 cm) above oor.

Equipment shall be mounted on 6" (15.2 cm) high metal legs with black enamel nish.

THE FOLLOWING APPLIES TO MODEL 403 (SINGLE DOOR) ONLY:

Doors shall have a 22-gauge stainless steel exterior, with a thermoformed ABS plastic

interior liner, and shall be fully insulated with foamed-in-place polyurethane. Door

handles shall be black, recessed and shall extend the full length of the top of the door.

Cabinet shall have (2) adjustable epoxy-coated wire shelves installed.

Optional accessories & modications

Stainless steel back

Plastic laminate on front

Additional wire shelves

Stainless steel single-tier overshelf

3.5" (8.9 cm) diameter casters

5" (12.7 cm) diameter casters

Door lock

Full-size composite-type cutting top

220 volt, 50 Hertz electrical system

Model 403

PAGE 1
PROJECT ITEM # QUANTITY DATE APPROVAL 403 Self-contained compact work top freezers Short form specifications Model 403 Exterior top shall be one-piece, 22-gauge stainless steel with front edge turned down to form nosing and rear edge turned up to form a 2" (5.1 cm) thick by 4" (10.2 cm) high backsplash. Exterior back and bottom shall be one-piece 24-gauge galvanized metal. Exterior ends shall be 22-gauge stainless steel.
PAGE 2
403 Self-contained compact work top freezers 27.25" 69.2 cm SHELF SUPPORT SPACING A = 7.50"/19.1 cm B = 4.00"/10.2 cm C = 3.75"/9.5 cm D = 2.75"/7.0 cm E = 6.00"/15.2 cm 28.50" 72.4 cm 28.50" 72.4 cm 2.00" 5.1 cm A PLAN VIEW MODEL 403 4.00" 10.2 cm 19.50" 49.5 cm B 35.50" 90.2 cm C D E 39.50" 100.3 cm 17.00" 43.2 cm 6.00" 15.2 cm 39.50" 100.3 cm 1.00"/2.5 cm BULLET FEET CAN ADJUST UPWARDS ONLY, RUBBER BUMPER UP TO+1.00"/2.5 cm INTERIOR CLEAR DIMENSION, LEFT TO RIGHT: 21.25"/54.0 cm FRZR. 27.