APC 2M-14 Quick Installation Guide Revision 1.2 19 February 2011 Copyright © 2011 Deliberant www.deliberant.
Copyright © 2011 Deliberant This user’s guide and the software described in it are copyrighted with all rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language in any form by any means without the written permission of Deliberant. Notice Deliberant reserves the right to change specifications without prior notice.
Quick Installation Guide Contents Contents Copyright ............................................................................................................................................. 2 Notice .................................................................................................................................................. 2 Trademarks .........................................................................................................................................
Quick Installation Guide Introduction Introduction FCC Warning This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Quick Installation Guide Introduction The R&TTE Directive repeals and replaces in the directive 98/13/EEC (Telecommunications Terminal Equipment and Satellite Earth Station Equipment) As of April 8, 2000. Safety This equipment is designed with the utmost care for the safety of those who install and use it. However, special attention must be paid to the dangers of electric shock and static electricity when working with electrical equipment.
About this Guide Quick Installation Guide About this Guide Prerequisite Skills and Knowledge To use this document effectively, you should have a working knowledge of Local Area Networking (LAN) concepts and wireless Internet access infrastructures. Definitions, Acronyms and Abbreviations The following typographic conventions and symbols are used throughout this document: Additional information that may be helpful but which is not required. Important information that should be observed.
Quick Installation Guide Installation Installation This chapter provides installation instructions for the hardware components of the APC 2M-14. Package Contents The figure below displays APC 2M-14 package contents.
Quick Installation Guide Installation Hardware Introduction APC 2M-14 is housed in a plastic enclosure ensuring a reliable sealing in a wide range of temperature and has an integrated 14dBi panel antenna.
Installation Quick Installation Guide LEDs The APC 2M-14 has 6 LEDs located on the side panel: power, LAN and 4 RSSI LEDs (refer at the Figure 2 – APC 2M-14 Overview for details). The various states of the LEDs indicate different connection operations as follows: LED Color Status Indication Power Green On APC 2M-14 is active/working Off No power on APC 2M-14 On LAN connection exists. Blinking Indicates the traffic on LAN interface. Off No LAN connection.
Quick Installation Guide Installation Step 4. For pole mounting attach APC 2M-14 on pole with U bolt (items H and J in the Figure 1 – APC 2M-14 Package Contents) as shown in picture below: Step 5. Connect Ethernet cable into the APC 2M-14 then insert a rubber gasket (item F in the Figure 1 – APC 2M-14 Package Contents) into CAT5 Ethernet connector gland and tighten with gland cap (item E in the Figure 1 – APC 2M-14 Package Contents) as displayed below: Step 6.
Quick Installation Guide Access the APC 2M-14 Access the APC 2M-14 The first connection to the APC 2M-14 can be made using a standard Ethernet cable connected directly to your PC. See next sections for the instructions on how to access the APC 2M-14 management interfaces. Connection via WEB browser The default IP address of the APC 2M-14 is 192.168.2.66 with a subnet mask of 255.255.255.0. Step 1. Configure your PC with a static IP address on the 192.168.2.0 subnet with mask 255.255.255.0.
Quick Installation Guide Access the APC 2M-14 Resetting to Factory Defaults APC 2M-14 has the capability of being reset to defaults by pinging the device with a certain packet size when the device is booting. During the startup of the device, when the drivers of the ethernet interfaces are loaded, the reset daemon is started. The daemon suspends startup process for 3 seconds and waits for ICMP "echo request" packet of length 369 bytes.
