EURO 25 -1 Vented Gas Fireplace Insert Heating Appliance For use with natural gas or propane* Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance. WHAT TO DO IF YOU SMELL GAS: ∗ Do not try to light any appliance ∗ Open windows ∗ Do not touch any electrical switch; do not use any phone in your building ∗ Extinguish any open flame ∗ Immediately call your gas supplier from a neighbor’s phone.
INTRODUCTION Congratulations on purchasing the Archgard Euro-25 Gas Fireplace Insert Heater! The Euro-25 is one of the most advanced gas heating appliances on the market. It is designed using the latest technology and manufactured to the highest quality.
EURO 25 -1 4 STATE OF MASSACHUSETTS REQUIREMENTS 5.08: Modifications to NFPA-54, Chapter 10 (2) Revise 10.8.
TABLE OF CONTENTS Page Caution & Safety Information 5 General Information 6 Appliance Description and Dimensions 7 Installation Instructions 8 Log Placement 15 Operation Instructions 20 Maintenance 22 Troubleshooting Instructions 23 Servicing 25 APPENDIX A - Installation Into Vented Gas Fireplaces 28 Suitable Host Fireplaces / Specific Installation Instructions 32 Important Information Form 37 Warranty 38 Replacement Parts 39 Notes 40 Warranty Registration Card 41
EURO 25 -1 6 CAUTION Due to high temperatures, the appliance should be located out of traffic and away from furniture and draperies. Children and adults should be alerted to the hazards of high surface temperature and stay away to avoid burns or clothing ignition. Young children should be carefully supervised when they are in the same room as the appliance. Clothing or other flammable material should not be placed on or near the appliance.
EURO 25 -1 7 GENERAL INFORMATION APPLIANCE CERTIFICATION This appliance is tested and certified to the following U.S. and Canadian gas appliance standards. - ANSI Z 21.88b-2003 / CSA 2.33b-2003, Vented Gas Fireplace Heater - CAN/CGA-2.17-M91, Gas-Fired Appliances for Use at High Altitudes. Please contact Archgard Industries Ltd., if you have any questions regarding the certification of these appliances. INSTALLATION CODES This appliance must be installed by a qualified gas appliance installer.
EURO 25 -1 8 APPLIANCE DESCRIPTION & DIMENSIONS FRONT VIEW SURROUND TOP LOUVERS BAY GLASS DOOR CONVECTION FAN SPEED CONTROL GAS VALVE SPARKER REMOVABLE CONTROL COVER APPLIANCE DIMENSIONS I J A G D K B C F E H A B C D E 30 ¼” 23” 15 ¼” 11 ¼” 4” (768 mm) (584 mm) (387 mm) (286 mm) (102 mm) F G H I J 19 ¼” 5” 5 ¾” 24 ¼” 16 ¼” Flue Collar - 4” (102 mm) diameter (489 mm) (127 mm) (146 mm) (616 mm) (413 mm) K Variable from 2 ½” (63.
EURO 25 -1 9 INSTALLATION INSTRUCTIONS CLEARANCES TO COMBUSTIBLES SIDE VIEW Combustible mantle allowed in shaded area. Mantle extension may be increased 1” (25 mm) for each additional 1” (25 mm) increase in clearance height. Minimum Height From Bottom of Appliance: 36” (915 mm) Minimum Height From Top of Surround: 13” (330 mm) 6” (152 mm) Leveling leg Non-combustible hearth is not required.* * Observe building codes; the codes may require a non-combustible hearth.
EURO 25 -1 10 INSTALLATION INSTRUCTIONS - Continued MINIMUM MASONRY FIREPLACE DIMENSIONS SIDE VIEW TOP VIEW Y Z 12” (305 mm) X 17” (432 mm) 19 ½” (495 mm) 25” (635 mm) The standard flue adapter will fit if X is more than 5 ¾”.
EURO 25 -1 11 INSTALLATION INSTRUCTIONS - Continued MINIMUM ZERO-CLEARANCE WOOD BURNING FIREPLACE DIMENSIONS SIDE VIEW TOP VIEW Y Z 12” (305 mm) X 17” (432 mm) 15 ¼” (387 mm) 25” (635 mm) The standard flue adapter will fit if X is more than 5 ¾”.
EURO 25 -1 12 INSTALLATION INSTRUCTIONS - Continued To install the Euro 25 into a vented gas fireplace, see APPENDIX A (page 24) for installation instructions. PRECAUTIONS • This appliance must be installed by a qualified gas installer and the installation must conform to the • • • • installation codes. This appliance needs fresh air for safe operation and must be installed so there are provisions for adequate combustion and ventilation air.
EURO 25 -1 13 INSTALLATION INSTRUCTIONS - Continued VENTING - Continued Caution: Make sure the flue adapter plate is not too far back, or the appliance will not vent properly. x X = ¼” minimum The arms can also be bent up and out of the way if the adapter plate is forward enough to interfere with the surround. The adapter plate must completely close with the appliance top plate. GAS CONNECTIONS Have your gas supplier or a qualified gas fitter run a gas supply line to the gas fireplace.
EURO 25 -1 14 INSTALLATION INSTRUCTIONS - Continued ATTACHMENT OF FIREPLACE SURROUND The surround has four hooks that clip onto the sides of the appliance. Make sure the surround sits evenly with the front of the fireplace. After the surround is properly installed, the bottom edge of the centre section of the surround is about ¾” from the top of the appliance.
EURO 25 -1 15 INSTALLATION INSTRUCTIONS - Continued GLASS DOOR WARNING: Glass door is fragile. Do not strike or abuse glass. Do not operate appliance with broken glass. Do not attempt to fix a broken glass door. It must be replaced with an identical one from the manufacturer. Do not attempt to remove the glass door when the appliance is hot. Removing the Glass Door Remove the louvers by lifting and unhooking it off the appliance. Remove the control cover by sliding it off the bottom door assembly.
EURO 25 -1 16 LOG PLACEMENT The following pages outline the steps for correctly placing the logs and platinum embers in your Euro 25-1. Upon completion, the logs and embers should look as shown in the photo below. WARNING: Do not place the logs or branches in any configuration other than the one shown. A fire, explosion or excessive carbon monoxide (CO) may result, causing property damage, personal injury or loss of life. STEP 1.
EURO 25 -1 17 LOG PLACEMENT - Continued STEP 2 - Locate log #136 and place onto rear log support using locator pins and pre-drilled holes in log. Log will sit as shown in the photo below. PINS FOR LOG # 136 STEP 3 - Locate log #137 and place onto the left side of the burner using locator pins and pre-drilled holes in log. Log will sit as shown in photo below.
EURO 25 -1 18 LOG PLACEMENT - Continued STEP 4 - Locate log #140 and place onto centre of burner using the locator pins and pre-drilled holes in log. Log should sit as shown in photo below. PIN HOLES FOR LOG # 140 STEP 5 - Locate log #141 and place onto right side of burner using the locator pins and pre-drilled holes in log. Log should sit as shown in photo below.
EURO 25 -1 19 LOG PLACEMENT - Continued STEP 6 - Locate log #135 and place onto rear log using the locator pins and pre-drilled holes in log. Log should sit as shown in photo below. PIN HOLE FOR LOG # 135 STEP 7 - Locate log #139 and place onto rear log using the locator pins and pre-drilled holes in log. Log should sit behind right grate tine as shown in photo below.
EURO 25 -1 20 LOG PLACEMENT - Continued STEP 8 - Locate log #138 and place onto rear log using the locator pins and pre-drilled holes in log. Log should sit behind left grate tine as shown in photo below. PIN HOLE FOR LOG # 138 FINAL LOG PLACEMENT - Please note that all logs should be placed exactly as shown.
EURO 25 -1 21 OPERATION INSTRUCTIONS FOR YOUR SAFETY, READ BEFORE LIGHTING INITIAL OPERATION • Check that the appliance is properly vented and connected to the gas supply. • Check that the logs and branches are properly placed. • Check all external parts, such as grills, door and control cover are properly attached and fastened. NOTE : When operated for the first few times, the appliance will emit odors and fumes. This is due to the evaporation of oils and solvents used in fabricating the appliance.
EURO 25 -1 22 OPERATION INSTRUCTIONS - Continued START-UP PROCEDURE 1. Set the thermostat, if present, to the lowest level. Set the flame adjustment knob to the HI position. Press slightly and turn the control knob clockwise 3 to the OFF position and wait 5 minutes; thus allowing any gases to escape which may have accumulated in the combustion chamber. Note: LP gases do not vent upward. Then follow step 2 and 3 to establish pilot. 2.
EURO 25 -1 23 MAINTENANCE CAUTION : Maintenance should only be conducted on a cold appliance. CLEANING THE APPLIANCE The exterior painted surfaces, glass and gold trims may be cleaned with a soft, non-abrasive cloth and water or a suitable, mild, non-abrasive cleaner. Regularly: • Clean and remove any lint accumulations or debris from the grills and in any • • • • combustion and convection air passageways.
EURO 25 -1 24 TROUBLESHOOTING Please check to make sure the instructions are followed exactly before attempting troubleshooting of the appliance. WARNING: Troubleshooting and servicing of gas and electrical devices of the appliance should only be conducted by a qualified service technician. SYMPTOM ACTION Pilot will not light after pressing the sparker many times. 1. When lighting the appliance for the first time after installation or after servicing, there is air in the gas line.
EURO 25 -1 25 TROUBLESHOOTING - Continued SYMPTOM ACTION The main burner does not turn on with 3. If using an optional thermostat, check to make sure the thermostat is set high enough the pilot lit. (continued) to turn on the appliance. 4. If using an optional remote switch, check that the remote switch or the thermostat is turned on. 5. Check for weak pilot flame. If flame is weak, check gas supply, check pilot flame adjustment and check for blockage of pilot orifice. 6.
EURO 25 -1 26 SERVICING SERVICING UNDER WARRANTY Before servicing, read the terms and conditions of the Archgard warranty at the back of the manual. Contact the Archgard authorized dealer from which you have purchased the appliance and provide him with details of the problem and the installation information which the installer has filled out at the back of this manual. WARNING: Servicing of this appliance must be conducted by a qualified service technician.
EURO 25 -1 27 SERVICING - Continued REPLACEMENT OF FAN • Disconnect the power to the appliance. • Remove the louvers, control cover door, brick panels, logs and burner. • Remove the firebox lower back. Remove the screws located at the back of the firebox. Take the lower firebox back out. Be careful not to damage the gasket. The fan is now visible. • Use a 11/32” hex socket and remove the three nuts holding the fan to the back of the firebox. Disconnect the spade connectors to the fan.
EURO 25 -1 28 SERVICING - Continued REPLACING MAJOR GAS COMPONENTS If any of the major gas components need to be replaced, such as the pilot or the gas valve, we recommend replacing the complete gas component assembly. The assembly is designed to be quickly and easily replaced with minimal inconvenience to the customer. Once replaced, the service technician can repair the defective assembly safely and comfortably in his shop and with the right tools and test equipment.
EURO 25 -1 29 APPENDIX A EURO 25-1 - INSTRUCTIONS FOR INSTALLATION INTO VENTED GAS FIREPLACES The Euro 25-1 may be retro-fitted into the following fireplaces: • CANADIAN HEATING PRODUCTS - MONTIGO 28 SERIES FIREHEARTH / MONTEREY - FIRESONG 220 SERIES ARCHGARD - MARQUIS T-100 SERIES GASGLO - GG 28 SERIES FMI - 450 and 850 SERIES • • • • PRECAUTIONS • • • • • This installation must be conducted by a qualified gas appliance installer and the installation must conform to the installation codes.
EURO 25 -1 30 APPENDIX A EURO 25-1 - INSTRUCTIONS FOR INSTALLATION INTO VENTED GAS FIREPLACES HOST GAS FIREPLACE PREPARATION • • • • • • • • The following procedures must be conducted by a qualified gas appliance installer. Double check the minimum firebox dimensions. Disconnect electrical power and gas supply. Remove the burner or sandpan, pilot, and all parts of the gas train assembly. Attach the Archgard modification warning plate (see sample, page 26) to the host fireplace label.
EURO 25 -1 31 APPENDIX A EURO 25-1 - INSTRUCTIONS FOR INSTALLATION INTO VENTED GAS FIREPLACES VENTING OF THE EURO-25-1 INSIDE THE HOST GAS FIREPLACE A connector kit (BCV4-KIT or BCV5-KIT) is used to connect the EURO 25-1 insert to the host gas fireplace’s venting system. The connector slips into the host fireplace’s B-vent. • Follow the connector kit’s instructions in assembling the kit.
EURO 25 -1 32 APPENDIX A EURO 25-1 - INSTRUCTIONS FOR INSTALLATION INTO VENTED GAS FIREPLACES SAMPLE MODIFICATION WARNING PLATE WARNING: This fireplace has been modified for use with the Archgard EURO-25-1 gas insert. Usage without the EURO-25-1 gas insert may cause property damage, personal injury or loss of life. 303-0050 SAMPLE WARNING LABEL WARNING: This fireplace has been modified for use with the Archgard EURO-25-1 gas insert.
EURO 25 -1 33 INSTALLATION INSTRUCTIONS INSTALLING THE EURO 25-1 GAS FIREPLACE INSERT HEATING APPLIANCE INTO VENTED ZERO-CLEARANCE GAS FIREPLACE: CANADIAN HEATING PRODUCT MODEL MONTIGO 28 SERIES CAUTION: Installation must be conducted by a qualified gas appliance installer. Gas and electrical power must be disconnected from the host gas fireplace before installation can begin. 1. Remove the louvers and screens or glass door. 2.
EURO 25 -1 34 INSTALLATION INSTRUCTIONS INSTALLING THE EURO 25-1 GAS FIREPLACE INSERT HEATING APPLIANCE INTO VENTED ZERO-CLEARANCE GAS FIREPLACE: FIREHEARTH / MONTEREY MODEL FIRESONG 220 SERIES CAUTION: Installation must be conducted by a qualified gas appliance installer. Gas and electrical power must be disconnected from the host gas fireplace before installation can begin. 1. Unhook the screen rod at the center and remove screens or glass door. 2.
EURO 25 -1 35 INSTALLATION INSTRUCTIONS INSTALLING THE EURO 25-1 GAS FIREPLACE INSERT HEATING APPLIANCE INTO VENTED ZERO-CLEARANCE GAS FIREPLACE: GASGLO MODEL GG 28 SERIES CAUTION: Installation must be conducted by a qualified gas appliance installer. Gas and electrical power must be disconnected from the host gas fireplace before installation can begin. 1. 2. 3. 4. 5. 6. 7. 8. Remove the screens and rod or glass door. Remove the bottom door track. Remove the pilot and valve assembly.
EURO 25 -1 36 INSTALLATION INSTRUCTIONS INSTALLING THE EURO 25-1 GAS FIREPLACE INSERT HEATING APPLIANCE INTO VENTED ZERO-CLEARANCE GAS FIREPLACE: ARCHGARD T-100 SERIES CAUTION: Installation must be conducted by a qualified gas appliance installer. Gas and electrical power must be disconnected from the host gas fireplace before installation can begin. 1. Remove the louvers and screens or glass door. 2. Remove the burner/sandpan assembly, valve and pilot assembly from the firebox bottom plate.
EURO 25 -1 37 INSTALLATION INSTRUCTIONS INSTALLING THE EURO 25-1 GAS FIREPLACE INSERT HEATING APPLIANCE INTO VENTED ZERO-CLEARANCE GAS FIREPLACE: FMI MODEL 850 SERIES CAUTION: Installation must be conducted by a qualified gas appliance installer. Gas and electrical power must be disconnected from the host gas fireplace before installation can begin. 1. 2. 3. 4. 5. 6. 7. Remove the screens or glass door. Remove the burner assembly. (two 5/16” Hex screws at the back) Remove the brick panels.
EURO 25 -1 38 IMPORTANT INFORMATION * Please have the installer fill out the installation information for warranty and future reference.
ARCHGARD LIMITED WARRANTY This Limited Warranty is made by ARCHGARD INDUSTRIES LTD., hereinafter referred to as “Archgard”. Archgard warrants to the original purchaser of an Archgard gas burning fireplace (s) that the product will be free of defects in materials and workmanship under normal use and service, for a “lifetime”. INCLUSIONS: “LIFETIME LIMITED WARRANTY“ ❖ All heat exchangers, combustion chamber, burner tubes and pans. ❖ Ceramic Fiber Logs and Ceramic Brick Panels against splitting or cracking.
EURO 25 -1 40 REPLACEMENT PARTS FOR EURO 25-1 ITEM # DESCRIPTION QTY.
EURO 25 -1 NOTES 41
POSTAGE CUT ALONG LINE WARRANTY REGISTRATION ARCHGARD INDUSTRIES LTD. 7116 BEATTY DRIVE MISSION, B.C.
Archgard Industries Ltd. 7116 Beatty Drive Mission, B.C. V2V 6B4 Canada Website: www.archgard.