Copyright Safety information About this user’s guide Features of your new product Introduction Getting started Network setup (Dell 1130n only) Basic setup Media and tray Printing Management tools Maintenance Troubleshooting Supplies Specifications Appendix Glossary Dell 1130 Dell 1130n www.dell.com | www.support.dell.
adjusting adjusting tray size tray size booklet printing booklet printing booklets booklets change percentage of your document change percentage of your document cleaning cleaning inside inside outside outside a machine cleaning cleaningpanel a machine control control panel convention convention duplex printing (manual) duplex printing printer driver (manual) Embedded printer driverWeb Service general information Embedded Web Service favorites settings, for printing general information features favorites se
Copyright Information in this document is subject to change without notice. ©2010 Dell Inc. All rights reserved. Reproduction of these materials in any manner whatsoever without the written permission of Dell Inc. is strictly forbidden. Trademarks used in this text: Dell, the DELL logo, and Dell Toner Management System are trademarks of Dell Inc.; Microsoft, Windows, Windows Vista, and Windows Server are registered trademarks of Microsoft Corporation in the United States and/or other countries.
Safety information These warnings and precautions are included in order to prevent injury to you and others, as well as preventing any potential damage to your machine. Be sure to read and understand all of these instructions before using the machine. Use common sense for operating any electrical appliance and whenever using your machine. Also, follow all warnings and instructions marked on the machine and in the accompanying literature.
This could result in electric shock or fire. Call an electrician to change the electrical outlet, or this could result in electric shock. Be careful, the paper output area is hot. Burns could occur. Do not allow pets to chew on the AC power, telephone or PC interface cords. This could result in electric shock or fire and/or injury to your pet.
The machine could fall, causing human injury or machine damage. The machine should be connected to the power level which is specified on the label. If you are unsure and want to check the power level you are using, contact the electrical utility company. Do not overload wall outlets and extension cords. This can diminish performance, and could result in electric shock or fire. Use only No.26 AWG [a] or larger, telephone line cord, if necessary. Otherwise, it can cause damage to the machine.
About this user’s guide This user’s guide provides information about basic understanding of the machine as well as detailed explanation on each step during actual usage. Read the safety information before using the machine. If you have a problem using the machine, refer to the troubleshooting chapter. (See Troubleshooting.) Terms used in this user’s guide are explained in the glossary chapter. (See Glossary.
Driver Help printing. (See Using help.) Dell website If you have Internet access, you can get help, support, printer drivers, manuals, and order information from the Dell websites www.dell.com or support.dell.com.
Features of your new product Your new machine is equipped with a number of special features that improve the quality of the documents you print. Special Features Print with excellent quality and speed You can print with a resolution of up to 1,200 x 600 dpi (Dell 1130) and up to 1,200 x 1,200 dpi (Dell 1130n) effective output. Dell 1130 prints up to 18 ppm, A4-sized paper or up to 19 ppm, letter sized paper. Dell 1130n prints up to 24 ppm, A4-sized paper and letter-sized paper.
Features by Models The machine is designed to support all of your document needs from printing to more advanced networking solutions for your business. Features by models include: FEATURES Hi-Speed USB 2.0 Dell 1130 Dell 1130n ● [a] Network Interface Ethernet 10/100 BaseTX wired LAN Duplex (2-sided) printing (Manual) [a] USB 1.
Introduction This chapter gives you an overview of your machine: This chapter includes: Machine overview Control panel overview Understanding the control panel Machine overview Front view This illustration may differ from your machine depending on its model.
This illustration may differ from your machine depending on its model. 1 Rear cover 3 USB port 2 Network Port [a] 4 Power receptacle [a] Dell 1130n only. Control panel overview This control panel may differ from your machine depending on its model. 1 Jam Shows the status of jam occurrence of your machine. (See LEDs.) 2 Online/Error Shows the status of your machine. (See LEDs.) 3 Cancel Stops an operation at any time. Also there are more functions. (See Understanding the control panel.
LED Jam ( Status ) Orange On Online/Error Off ) ( Green Description A paper jam has occurred. (See Clearing paper jams.) The machine is off-line. On The machine is in power saver mode. The machine is on-line and can receive data from the computer. Blinking When the LED blinks slowly, the machine is receiving data from the computer. When the LED blinks rapidly , the machine is printing data. Red On The cover is open. Close the cover. There is no paper in the tray. Load paper in the tray.
(Power button) This button must be used to turn the machine on/off. Turning on the machine 1. 2. Plug in the power cord. Press (power) on the control panel. If you want to turn the power off, press and hold this button for 1 second.
Getting started This chapter gives you step-by-step instructions for setting up the USB connected machine and software. This chapter includes: Setting up the hardware Printing a demo page Supplied software System requirements Installing USB connected machine’s driver Sharing your machine locally Setting up the hardware This section shows the steps to set up the hardware, as is explained in the Quick Install Guide. Make sure you read the Quick Install Guide first and follow the steps below: Location 1.
Unpack the machine and check all the enclosed items. 2. 3. 4. 5. 6. 7. Remove tape holding the machine. Install the toner cartridge. Load paper. (See Loading paper in the tray.) Make sure that all cables are connected to the machine. Turn the machine on. (See Turning on the machine.) This equipment will be inoperable when mains power fails. Printing a demo page Print a demo page to make sure that the machine is operating correctly. To print a demo page: (cancel button) for about 2 seconds.
MB) Windows XP Intel® Pentium® III 933 MHz (Pentium IV 1 GHz) 128 MB (256 MB) 1.5 GB Windows Server® 2003 Intel® Pentium® III 933 MHz (Pentium IV 1 GHz) 128 MB (512 MB) 1.
Only use an USB cable shorter than 3 m (118 in. ). Windows You can install the machine software using the typical or custom method. The following steps below are recommended for most users who use a machine directly connected to your computer. All components necessary for machine operations will be installed. 1. Make sure that the machine is connected to the computer and powered on. If the “Found New Hardware Wizard” window appears during the installation procedure, click Cancel in close the window. 2.
If your machine is not connected to the computer, the following window will appear. After connecting the machine, click Next. If you don’t want to connect the printer at this time, click Next, and No on the following screen. The installation starts and a test page will not print at the end of the installation. The installation window in this user guide may differ depending on the machine and interface in use. 5. After the installation is finished, a window asking you to print a test page appears.
Apple LaserWriter driver (only available when you use a machine which supports the PostScript driver) for printing on a Macintosh computer. 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. Make sure that the machine is connected to your computer and powered on. Insert the supplied software CD into your CD/DVD drive. Double-click the CD-ROM icon that appears on your Macintosh desktop. Double-click the MAC_Installer folder. Double-click the Installer OS X icon. Enter the password and click OK.
3. Insert the supplied software CD into your CD/DVD drive. The software CD will run automatically. If the software CD does not run automatically, click the icon at the bottom of the desktop. When the Terminal screen appears, type in the following: If the software CD is secondary master and the location to mount is /mnt/cdrom, [root@localhost root]#mount -t iso9660 /dev/hdc /mnt/cdrom [root@localhost root]#cd /mnt/cdrom/Linux [root@localhost Linux]#./install.
4. 5. 6. If the software CD is secondary master and the location to mount is /mnt/cdrom, [root@localhost root]#mount -t iso9660 /dev/hdc /mnt/cdrom [root@localhost root]#cd /mnt/cdrom/Linux [root@localhost Linux]#./uninstall.sh The installation program runs automatically if you have an autorun software package installed and configured. Click Uninstall. Click Next. Click Finish. Sharing your machine locally Follow the steps below to set up the computers to share your machine locally.
In case host computer requires User name and Password, fill in User ID and password of the host computer account. 5. 6. 7. Right click the printer icon you want to share and select Connect. If a set up complete message appears, click OK. Open the file you want to print and start printing. Macintosh The following steps are for Mac OS X 10.5~10.6. Refer to Mac Help for other OS versions. Setting up a host computer 1. 2. 3. 4. Install your printer driver. (See Macintosh.
Network setup (Dell 1130n only) This chapter gives you step-by-step instructions for setting up the network connected machine and software. This chapter includes: Network environment Introducing useful network programs Using a wired network Installing network connected machine’s driver IPv6 Configuration Network environment You need to set up the network protocols on the machine to use it as your network machine.
You must set up the network protocols on your machine to use it on your network. This chapter will show you how this is accomplished. You can use network after connecting network cable to a corresponding port on your machine. Printing network configuration report You can print a Network Configuration Report from the machine's control panel that will show the current machine’s network settings. This will help you to set up a network and troubleshooting problems.
5. Enter the machine’s new information into the configuration window as follows. In a corporate intranet, you may need to have this information assigned by a network manager before proceeding. MAC Address : Find the machine’s MAC address from the Network Configuration Report and enter it without the colons. For example, 00:15:99:29:51:A8 becomes 0015992951A8. IP Address: Enter a new IP address for your printer. For example, if your computer’s IP address is 192.168.1.150, enter 192.168.1.X.
2. Insert the supplied software CD into your CD/DVD drive. The software CD should automatically run and an installation window appear. If the installation window does not appear, click Start and then Run. Type X:\Setup.exe, replacing “X” with the letter which represents your drive. Click OK. If you use Windows Vista, Windows 7 and Windows 2008 Server R2 click Start > All programs > Accessories > Run. Type X:\Setup.exe replacing “X” with the letter which represents your drive and click OK.
If you do not see your printer on the list, click Update to refresh the list, or select Add TCP/IP Port to add your printer to the network. To add the printer to the network, enter the port name and the IP address for the printer. To verify your printer’s IP address, print a Network Configuration page. (By pressing the about 5 seconds, then release. (Example IP Address is 13.121.52.
10. 11. After the installation is finished, click Quit. Open the Applications folder > Utilities > Print Setup Utility. For Mac OS X 10.5~10.6, open the Applications folder > System Preferences and click Print & Fax. 12. Click Add on the Printer List. For Mac OS X 10.5~10.6, click the “+” icon; a display window will pop up. 13. For Mac OS X 10.3, select the IP Printing tab. For Mac OS X10.4, click IP Printer. For Mac OS X 10.5~10.6, click IP. 14. Select Socket/HP Jet Direct in Printer Type.
1. 2. 3. 4. 5. 6. 7. 8. Double-click the Unified Driver Configurator. Click Add Printer… The Add printer wizard window opens. Click Next. Select Network printer and click the Search button. The printer’s IP address and model name appears on list field. Select your machine and click Next. Input the printer description and Next When the add printer is done, click Finish. IPv6 Configuration TCP/IPv6 is supported properly only in Windows Vista or higher.
Enter the rest of address. (ex: 3FFE:10:88:194::AAAA. “A” is the hexadecimal 0 through 9, A through F.) 6. Click the Apply button. Installing printer driver Driver installation for network printer in IPv6 network environment is same as TCP/IPv4. (See Installing network connected machine’s driver.) Select TCP/IP Port and when the list of machines is displayed, simply select your machine's IPv6 address. Using Embedded Web Service 1. 2.
Basic setup After installation is complete, you may want to set the machine’s default settings. Refer to the next section if you would like to set or change values. This chapter gives you step-by-step instructions for setting up the machine. This chapter includes: Altitude adjustment Setting the default tray and paper Changing font setting (Dell 1130n only) Altitude adjustment The print quality is affected by atmospheric pressure, which is determined by the height of the machine above sea level.
Setting the default tray and paper You can select the tray and paper you would like to keep using for printing job. In the computer Windows 1. 2. Click the Windows Start menu. For Windows 2000, select Settings > Printers. For Windows XP/Server 2003, select Printer and Faxes. For Windows Server 2008/Vista, select Control Panel > Hardware and Sound > Printers. For Windows 7, select Control Panel > Hardware and Sound > Devices and Printers.
For Dell 1130n You change power save in Printer Settings Utility. 1. You can launch it from the Start menu, select Programs or All Programs > Dell > Dell Printers > your printer driver name > Printer Settings Utility. 2. Click Power Save. Select the appropriate value from the dropdown list, and then click Apply. Changing font setting (Dell 1130n only) Your machine has preset font setting depending on your region or country.
Media and tray This chapter provides information on how to load print media into your machine. This chapter includes: Selecting print media Changing the tray size Loading paper in the tray Printing on special media Using the output support Selecting print media You can print on a variety of print media, such as plain paper, envelopes, labels, and transparencies. Always use print media that meet the guidelines for use with your machine.
The tray is preset to Letter or A4 size, depending on your country. To change the size, you need to adjust the paper guides. 1. 2. 3. 4. Support guide Paper length guide Guide lock Paper width guide 1. With one hand press and hold the guide lock, and with the other hand, hold the paper length guide and support guide together. Slide the paper length guide and support guide to locate them in the correct paper size slot. 2.
Do not push the paper width guide too far causing the media to warp. If you do not adjust the paper width guide, it may cause paper jams. Do not use a paper with more than 6 mm curl. Loading paper in the tray Tray 1 1. 2. Pull out the paper tray . And adjust the tray size to the media size you are loading. (See Changing the tray size.) 3. And place paper with the side you want to print facing down. 4. Set the paper type and size for the tray 1. (See Setting the default tray and paper.
Tips on using the manual tray If you select Manual Feeder for Source from your software application, you need to press (cancel button) each time you print a page and load only one type, size and weight of print media at a time in the manual tray. To prevent paper jams, do not add paper while printing. This also applies to other types of print media. Print media should be loaded face up with the top edge going into the manual tray first and be placed in the center of the tray.
CardStock ● Labels ● Transparency ● Envelope ● Preprinted ● Cotton ● Recycled ● ● Archive ● ● ( ●: supported, Blank: Not supported) The media types are shown in the Printing Preferences. This paper type option allows you to set the type of paper to be loaded in the tray. This setting appears in the list, so that you can select it. This will let you get the best quality printout. If not, the desired print quality may not be achieved. Plain: 60 to 120 g/m 2 (16 to 32 lb) Normal plain paper.
When selecting envelopes, consider the following factors: Weight: The weight of the envelope paper should not exceed 90 g/m 2 otherwise, jam may occur. Construction: Prior to printing, envelopes should lie flat with less than 6 mm curl, and should not contain air. Condition: Envelopes should not be wrinkled, nicked, nor damaged. Temperature: Use envelopes that are compatible with the heat and pressure of the machine during operation. Use only well-constructed envelopes with sharp-and well-creased folds.
To avoid fading, do not expose printed transparencies to prolonged sunlight. Ensure that transparencies are not wrinkled, curled, or have any torn edges. Do not use transparencies that separates from the backing sheet. To prevent transparencies from sticking to each other, do not let the printed sheets stack up as they are begin printed out. Labels To avoid damaging the machine, use only labels designed for use in laser machines.
Letterhead/ Preprinted paper must be printed with heat-resistant ink that will not melt, vaporize, or release hazardous emissions when subjected to the machine’s fusing temperature about 170°C (338 °F) for 0.1 second. Letterhead/ Preprinted paper ink must be non-flammable and should not adversely affect machine rollers. Forms and letterhead should be sealed in a moisture-proof wrapping to prevent changes during storage. Before you load letterhead/preprinted paper, verify that the ink on the paper is dry.
Printing This chapter explains common printing tasks. This chapter includes: Printer driver features Basic printing Opening printing preferences Using help Using special print features Changing the default print settings Setting your machine as a default machine Printing to a file (PRN) Macintosh printing Linux printing The procedures in this chapter are mainly based on Windows XP.
Your Printing Preferences window that appears in this user’s guide may differ depending on the machine in use. However, the composition of the Printing Preferences window is similar. Check the operating system(s) that are compatible with your machine. Refer to the OS compatibility section of Printer Specifications. (See System requirements.) When you select an option in Printing Preferences, you may see a warning mark, , or .
You can also access this window by simply double-clicking the machine icon ( You can also cancel the current job by pressing ) in the Windows task bar. on the control panel. Opening printing preferences You can preview the settings you selected on the upper right of the Printing Preferences. 1. Open the document you want to print. 2. 3. 4. Select Print from the file menu. The Print window appears. Select your machine from the Select Printer. Click Properties or Preferences.
3. Click Add. When you save Presets, all current driver settings are saved. If you click Add, the Add button changes to Update button. Select more options and click Update, settings will be added to the Presets you made. To use a saved setting, select it from the Presets drop down list. The machine is now set to print according to the setting you selected. To delete saved setting, select it from the Presets drop down list and click Delete.
6. 7. Click the Paper tab, select the Size, Source, and Type. Click OK or Print until you exit the Print window. Printing posters This feature allows you to print a single-page document onto 4, 9, or 16 sheets of paper, for the purpose of pasting the sheets together to form one poster-size document. 1. To change the print settings from your software application, access Printing Preferences. (See Opening printing preferences.) 2. 3.
We recommend not to print on both sides of the special media, such as labels, envelopes, or thick paper to print on both sides of paper. It may cause a paper jam or damage the machine. The Double-Sided Printing (Manual) feature is available only for the tray 1. 1. To change the print settings from your software application, access Printing Preferences. (See Opening printing preferences.) 2. 3. Click the Advanced tab. From the Double-Sided Printing (Manual) section, select the binding option you want.
2. 3. 4. 5. Click the Paper tab. Select the paper size you want from the Fit to Page. Select the Size, Source, and Type in Paper Options. Click OK or Print until you exit the Print window. Using watermarks The watermark option allows you to print text over an existing document. For example, you use it when you want to have large gray letters reading “DRAFT” or “CONFIDENTIAL” printed diagonally across the first page or all pages of a document.
4. Click OK or Print until you exit the Print window. Using overlay An overlay is text and/or images stored in the computer hard disk drive (HDD) as a special file format that can be printed on any document. Overlays are often used to take the place of letterhead paper. Rather than using preprinted letterhead, you can create an overlay containing exactly the same information that is currently on your letterhead.
2. 3. 4. 5. 6. Select Edit in the Overlay drop down list. Select the overlay you want to delete from the Overlay List box. Click Delete. When a confirming message window appears, click Yes. Click OK or Print until you exit the Print window. Advanced Options Use the following Graphics options to adjust the print quality for your specific printing needs. 1. To change the print settings from your software application, access Printing Preferences. (See Opening printing preferences.) 2.
For Windows Server 2008/Vista, select Control Panel > Hardware and Sound > Printers. For Windows 7, select Control Panel > Hardware and Sound > Devices and Printers. For Windows Server 2008 R2, select Control Panel > Hardware > Devices and Printers. 3. 4. Right-click your machine. For Windows XP/Server 2003/Server 2008/Vista, press Printing Preferences. For Windows 7 and Windows Server 2008 R2, from context menus, select the Printing preferences.
3. Type in the destination path and the file name, and then click OK. For example c:\Temp\file name. If you type in only the file name, the file is automatically saved in My Documents. The saved folder may differ, depending on your operating system. Macintosh printing This chapter explains how to print using Macintosh. You need to set the print environment before printing. USB connected (See Macintosh.) Network connected (See Macintosh.
Pages per Sheet: This option determines how many pages to be printed on one page. (See Printing multiple pages on one sheet of paper.) Layout Direction: This option allows you to select the printing direction on a page similar to the examples on UI. Border: This option allows you to print a border around each page on the sheet. Reverse Page Orientation: This option allows you to rotate paper 180 degrees. Graphics The Graphics tab provides options for selecting Resolution.
Printer Settings Printer Settings tab provides Toner Save Mode, Reprint When Jammed, and Power Save options. Select Printer Settings from the drop-down list under Orientation to access the following features: Toner Save Mode: Selecting this option extends the life of your toner cartridge and reduces your cost per page without a significant reduction in print quality. Printer Setting: If you select this option, this feature is determined by the setting you’ve made from the machine.
3. 4. Select the other options you want to use. Click Print, then the machine prints the selected the number of pages you want to print on one sheet of paper. Linux printing Printing from applications There are a lot of Linux applications that allow you to print using Common UNIX Printing System (CUPS). You can print on your machine from any such application. 1. Open an application, and select Print from the File menu. 2. 3. Select Print directly using lpr. 4.
General: This option allows you to change the paper size, the paper type, and the orientation of the documents. It enables the duplex feature, adds start and end banners, and changes the number of pages per sheet. Text: This option allows you to specify the page margins and set the text options, such as spacing or columns. Graphics: This option allows you to set image options that are used when printing images/files, such as color options, image size, or image position.
3. The Printer Properties window opens. The following five tabs display at the top of the window: General: This option allows you to change the printer location and name. The name entered in this tab displays on the printer list in Printers configuration. Connection: This option allows you to view or select another port. If you change the machine port from USB to parallel or vice versa while in use, you must re-configure the machine port in this tab.
Management tools This chapter introduces management tools provided to help you make full use of your machine. This chapter includes: Introducing useful management tools Using Embedded Web Service (Dell 1130n only) Using the Printer Status Monitor Introducing useful management tools Using the printer settings utility Firmware update utility Using the Unified Linux Driver Configurator Introducing useful management tools The programs below help you to use your machine conveniently.
E-mail notification setup You can receive emails about your machine’s status by setting this option. By setting information such as IP address, host name, e-mail address and SMTP server information, the machine status (toner cartridge shortage or machine error) will be sent to the specified e-mail address automatically. This option may be used more frequently by a machine administrator. 1. Start a web browser, such as Internet Explorer, from Windows. Enter the machine IP address (http://xxx.xxx.xxx.
Status 2 Toner Level 3 4 View the level of toner remaining in the toner cartridge(s). Order Supplies Order replacement toner cartridge(s) online. Help me When error occurs, Help me button appears. You can directly open troubleshooting section in the user’s guide. Opening the Troubleshooting Guide Find solutions for problems by using the Troubleshooting Guide. Right-click the Printer Status Monitor icon and select Troubleshooting Guide.
1. 2. Printers Configuration Ports Configuration To use the on screen help, click Help. 3. After changing the configurations, click Exit to close the Unified Driver Configurator. Printers configuration Printers configuration has the two tabs: Printers and Classes. Printer tab View the current system’s printer configuration by clicking on the machine icon button on the left side of the Unified Driver Configurator window.
1 Switches to Printers configuration. 2 Shows all of the installed machine. 3 Shows the status, model name and URI of your machine. The printer control buttons are, as follows: Refresh: Renews the available machines list. Add Printer: Allows you to add a new machines. Remove Printer: Removes the selected machine. Set as Default: Sets the current selected machine as a default machine. Stop/Start: Stops/starts the machine. Test: Allows you to print a test page to ensure the machine is working properly.
1 Shows all of the machine classes. 2 Shows the status of the class and the number of machines in the class. Refresh: Renews the classes list. Add Class: Allows you to add a new machine class. Remove Class: Removes the selected machine class. Port configuration In this window, you can view the list of available ports, check the status of each port and release a port that is stalled in a busy state when its owner has terminated the job for any reason.
1 Switches to Ports configuration. 2 Shows all of the available ports. 3 Shows the port type, device connected to the port, and status. Refresh: Renews the available ports list. Release port: Releases the selected port.
Maintenance This chapter provides information for maintaining your machine and the toner cartridge. This chapter includes: Printing a machine report Using toner low alert (Dell 1130n only) Cleaning a machine Storing the toner cartridge Tips for moving & storing your machine Printing a machine report You can print a configuration page to view current printer settings, or to help troubleshoot printer problems. (cancel button) for about 5 seconds.
During the printing process, paper, toner, and dust particles can accumulate inside the machine. This buildup can cause print quality problems, such as toner specks or smearing. Cleaning the inside of the machine clears and reduces these problems. 1. Turn the machine off and unplug the power cord. Wait for the machine to cool down. 2. Open the front cover and pull the toner cartridge out.
6. Plug in the power cord and turn the machine on. Storing the toner cartridge Toner cartridges contain components that are sensitive to light, temperature, and humidity. Dell suggests users follow the recommendations to ensure the optimum performance, highest quality, and longest life from your new Dell toner cartridge. Store this cartridge in the same environment as the printer it will be used in; this should be in controlled office temperature and humidity conditions.
Troubleshooting This chapter gives helpful information for what to do if you encounter an error. This chapter includes: Redistributing toner Tips for avoiding paper curls Tips for avoiding paper jams Clearing paper jams Solving other problems Redistributing toner When the toner cartridge is near the end of its life: White streaks or light printing occurs. The LED blinks red. If this happens, you can temporarily improve print quality by redistributing the remaining toner in the cartridge.
5. Close the front cover. Ensure that the cover is securely closed. 1. 2. Open the rear cover. Tips for avoiding paper curls Pull down the pressure lever on each side. 1. Pressure lever Keep the rear cover opened during printing. Only use when the printout has more than 20 mm curl. Tips for avoiding paper jams By selecting the correct media types, most paper jams can be avoided. When a paper jam occurs, refer to the next guidelines. Ensure that the adjustable guides are positioned correctly.
If a paper jam occurs, the LED on the control panel lights orange. Find and remove the jammed paper. To resume printing after clearing paper jams, you must open and close the front cover. To avoid tearing the paper, pull the jammed paper out slowly and gently. Follow the instructions in the following sections to clear the jam. In tray Click this link to open an animation about clearing a jam. 1. Open and close the front cover. The jammed paper is automatically ejected from the machine.
2. Open and close the front cover to resume printing. Inside the machine Click this link to open an animation about clearing a jam. The fuser area is hot. Take care when removing paper from the machine. 1. Open the front cover and pull the toner cartridge out, lightly pushing it down. 2. Remove the jammed paper by gently pulling it straight out. 3. Replace the toner cartridge and close the front cover. Printing automatically resumes.
2. Gently pull the paper out of the output tray. If you do not see the jammed paper or if there is any resistance when you pull, stop and go to the next step. 3. 4. Open the rear cover. Pull the pressure levers down and remove the paper. Return the pressure levers to their original position. 1. Pressure lever If you do not see the jammed paper, go to next step. 5. Pull the fuser cover levers down and remove the paper. Return the fuser cover levers to their original position. The fuser area is hot.
The following chart lists some conditions that may occur and the recommended solutions. Follow the suggested solutions until the problem is corrected. If the problem persists, call for service. Power problems Click this link to open an animation about power problems. Condition The machine is not receiving power, or the connection cable between the computer and the machine is not connected properly. Suggested solutions Plug in the power cord and press control panel.
There is too much paper in the tray. Remove excess paper from the tray. The paper is too thick. Use only paper that meets the specifications required by the machine. (See Print media specifications.) The paper keeps jamming. There is too much paper in the tray. Remove excess paper from the tray. If you are printing on special materials, use the manual tray. An incorrect type of paper is being used. Use only paper that meets the specifications required by the machine. (See Print media specifications.
materials from the wrong paper source. selected in the Printing Preferences may be incorrect. found under the Paper tab within the Printing Preferences. Select the correct paper source. See the printer driver help screen. (See Opening printing preferences.) A print job is extremely slow. The job may be very complex. Reduce the complexity of the page or try adjusting the print quality settings. Half the page is blank. The page orientation setting may be incorrect.
If the entire page is light, the print resolution setting is too low or the toner save mode is on. Adjust the print resolution and turn the toner save mode off. See the help screen of the printer driver. A combination of faded or smeared defects may indicate that the toner cartridge needs cleaning. (See Cleaning the inside.) The surface of the LSU part inside the machine may be dirty. (See Cleaning the inside.
Vertical repetitive defects If marks repeatedly appear on the printed side of the page at even intervals: The toner cartridge may be damaged. If you still have the same problem, remove the toner cartridge and, install a new one. (See Replacing the toner cartridge.) Parts of the machine may have toner on them. If the defects occur on the back of the page, the problem will likely correct itself after a few more pages. The fusing assembly may be damaged. Contact a service representative.
The machine may require repair. Contact a service representative. Loose toner Clean the inside of the machine. (See Cleaning the inside.) Check the paper type and quality. (See Print media specifications.) Remove the toner cartridge and then, install a new one. (See Replacing the toner cartridge.) If the problem persists, the machine may require repair. Contact a service representative.
The machine does not print. Check if the printer driver is installed in your system. Open Unified Driver Configurator and switch to the Printers tab in Printers configuration window to look at the list of available machines. Make sure that your machine is displayed on the list. If not, open Add new printer wizard to set up your device. Check if the machine is started. Open Printers configuration and select your machine on the printers list. Look at the description in the Selected printer pane.
Supplies This chapter provides information on purchasing supplies and maintenance parts available for your machine. This chapter includes: How to purchase Available supplies Replacing the toner cartridge Available accessories may differ from country to country. Contact your sales representatives to obtain the list of available accessories. How to purchase To order Dell-authorized supplies and accessories visit www.dell.
3. 4. Take a new toner cartridge out of its package. 5. Locate the sealing tape at the end of the toner cartridge. Carefully pull the tape completely out of the cartridge and discard it. Remove the paper protecting the toner cartridge by pulling the packing tape. The sealing tape should be longer than 60 cm when correctly removed. Holding the toner cartridge, pull the sealing tape straight to remove it from the cartridge. Be careful not to cut the tape.
8. Close the front cover. Make sure that the cover is securely closed.
Specifications This chapter guides you about this machine’s specifications. This chapter includes: Hardware specifications Environmental specifications Electrical specifications Print media specifications The specification values here are based on preliminary data. See www.dell.com or support.dell.com for current information. Hardware specifications Item Dimension Weight Description Height 197 mm (7.76 inches) Depth 389 mm (15.31 inches) Width 360 mm (14.
Ready mode Dell 1130: Less than 45 W Dell 1130n: Less than 60 W Power save mode Dell 1130: Less than 4.5 W Dell 1130n: Less than 6.5 W Power off mode [a] Less than 0.8 W See the rating label on the machine for the correct voltage, frequency (hertz) and type of current for your machine. Print media specifications Type Plain paper Envelope Size Dimensions Print media weight [a] /Capacity[b] Tray1 Letter 216 x 279 mm (8.50 x 11.00 inches) Legal 216 x 356 mm (8.50 x 14.
(4.49 x 6.38 inches) Thick paper Refer to the Plain paper section Refer to the Plain paper section 90 g/m 2 (24 lb bond) 90 g/m 2 (24 lb bond) 1 sheet stacking Thin paper Refer to the Plain paper section Refer to the Plain paper section 60 to 70 g/m 2 (16 to 19 lb bond) 60 to 70 g/m 2 (16 to 19 lb bond) 1 sheet stacking Transparency Refer to the Plain paper section Refer to the Plain paper section Not available in tray1. 138 to 146 g/m 2 (36.81 to 38.
Appendix Dell technical support policy Technician-assisted technical support requires the cooperation and participation of the customer in the troubleshooting process and provides for restoration of the Operating System, application software, and hardware drivers to the original default configuration as shipped from Dell, as well as the verification of appropriate functionality of the printer and all Dellinstalled hardware.
Glossary The following glossary helps you get familiar with the product by understanding the terminologies commonly used with printing as well as mentioned in this user’s guide. 802.11 802.11 is a set of standards for wireless local area network (WLAN) communication, developed by the IEEE LAN/MAN Standards Committee (IEEE 802). 802.11b/g 802.11b/g can share same hardware and use the 2.4 GHz band. 802.11b supports bandwidth up to 11 Mbps; 802.11g up to 54 Mbps. 802.
Control Panel A control panel is a flat, typically vertical, area where control or monitoring instruments are displayed. They are typically found in front of the machine. Coverage It is the printing term used for a toner usage measurement on printing. For example, 5% coverage means that an A4 sided paper has about 5% image or text on it. So, if the paper or original has complicated images or lots of text on it, the coverage will be higher and at the same time, a toner usage will be as much as the coverage.
warranty period. For example, if the duty cycle is 48,000 pages per month assuming 20 working days, a printer limits 2,400 pages a day. ECM Error Correction Mode (ECM) is an optional transmission mode built into Class 1 fax machines or fax modems. It automatically detects and corrects errors in the fax transmission process that are sometimes caused by telephone line noise. Emulation Emulation is a technique of one machine obtaining the same results as another.
IEEE The Institute of Electrical and Electronics Engineers (IEEE) is an international non-profit, professional organization for the advancement of technology related to electricity. IEEE 1284 The 1284 parallel port standard was developed by the Institute of Electrical and Electronics Engineers (IEEE). The term "1284-B" refers to a specific connector type on the end of the parallel cable that attaches to the peripheral (for example, a printer).
photographic images. It is the format used for storing and transmitting photographs on the World Wide Web. LDAP The Lightweight Directory Access Protocol (LDAP) is a networking protocol for querying and modifying directory services running over TCP/IP. LED A Light-Emitting Diode (LED) is a semiconductor device that indicates the status of a machine. MAC address Media Access Control (MAC) address is a unique identifier associated with a network adapter.
Open Systems Interconnection (OSI) is a model developed by the International Organization for Standardization (ISO) for communications. OSI offers a standard, modular approach to network design that divides the required set of complex functions into manageable, self-contained, functional layers. The layers are, from top to bottom, Application, Presentation, Session, Transport, Network, Data Link and Physical.
The sharpness of an image, measured in Dots Per Inch (DPI). The higher the dpi, the greater the resolution. SMB Server Message Block (SMB) is a network protocol mainly applied to share files, printers, serial ports, and miscellaneous communications between nodes on a network. It also provides an authenticated Inter-process communication mechanism. SMTP Simple Mail Transfer Protocol (SMTP) is the standard for e-mail transmissions across the Internet.
USB Universal Serial Bus (USB) is a standard that was developed by the USB Implementers Forum, Inc., to connect computers and peripherals. Unlike the parallel port, USB is designed to concurrently connect a single computer USB port to multiple peripherals. Watermark A watermark is a recognizable image or pattern in paper that appears lighter when viewed by transmitted light.
