Dell™ Wireless 2350 Broadband Router User's Guide Contents Introduction Overview Wireless Networking Overview A Look at the Hardware Installation and Configuration Cable Modem Connection DSL Modem Connection Cable Modem with USB Connection Configuring Your Dell Wireless 2350 Broadband Router as an Access Point for an Existing Network Configuring Your Dell Wireless 2350 Broadband Router for Gaming Setting Wireless Encryption in Your Router Turning Off Broadcast SSID Setting Up File and Printer Sharing How T
P/N Y6925 Revision A01, December 2004
Back to Contents Page Introduction: Dell™ Wireless 2350 Broadband Router User's Guide Overview Wireless Networking Overview A Look at the Hardware Overview The Dell Wireless 2350 Broadband Router is an 802.11b/g wireless access point with a built-in Internet router. Connecting to a DSL or cable modem, the Dell Wireless 2350 Broadband Router can offer both wired and wireless computers simultaneous access to the Internet.
-port Ethernet switch: Connects four wired computers for file and print sharing. Ethernet bridge: Enables file and print sharing between wired and wireless computers. In addition, connects to an Ethernet hub, extending Internet connectivity and sharing to more wired computers. The Dell Wireless 2350 Broadband Router supports up to 252 connect computers when used with additional router devices. Up to 16 of the 252 computers can be connected wirelessly.
Back to Contents Page Wireless Networking Overview: Dell™ Wireless 2350 Broadband Router User's Guide Wireless Local Area Network (WLAN) Identifying a WLAN Encryption Automatic Rate Selection and Rate Scaling Wireless Local Area Network (WLAN) A Local Area Network (LAN) is a network in one location. Computers at that location can share files, printers, and other services. In a LAN, a networked computer that requests services is called a client.
numbers, called an encryption key. Before transmitting information over the airwaves, the wireless client or access point encrypts or scrambles the information. The access point or wireless client receiving the information uses the same key to decrypt or unscramble the information. The information is only readable to WLAN devices that have the correct encryption key. The longer the key is, the stronger the encryption.
representing English characters as numbers, with each letter assigned a number from 0 to 127. For example, the ASCII code for uppercase M is 77. Most computers use ASCII codes to represent text, which makes it possible to transfer data from one computer to another. WPA WPA (Wi-Fi Protected Access) is an upgrade to the WEP standard for securing your wireless network. WPA is derived from and will be forward-compatible with the future IEEE 802.11i standard.
Back to Contents Page A Look at the Hardware: Dell™ Wireless 2350 Broadband Router User's Guide Front Panel Back Panel Front Panel The Dell Wireless 2350 Broadband Router has seven Light Emitting Diodes (LEDs), or link lights, on its front side. The following table defines the behaviour for each LED: Front Panel LED Represents Power Power Wireless Wireless LAN Activity The Power LED will light up green when the device is powered on. It will blink when the device is powering up or when it is reset.
Dell Wireless 2350 Broadband Router. Internet DSL or cable modem A steady green light indicates the connection is active (i.e. the Dell Wireless 2350 Broadband Router is connected to a xDSL or cable modem) and blinks with data activity. LAN LAN LAN LAN Local Area Network A steady green light indicates the connection is active and blinks with data activity.
Back to Contents Page
Back to Contents Page Installation and Configuration: Dell™ Wireless 2350 Broadband Router User's Guide Cable Modem Connection DSL Modem Connection Cable Modem with USB Connection Configuring Your Router as an Access Point for an Existing Network Configuring Your Dell Wireless 2350 Broadband Router for Gaming Setting Wireless Encryption in Your Dell Wireless 2350 Broadband Router Turning Off Broadcast SSID Setting Up File and Printer Sharing How To Setup Microsoft® Windows® XP Clients Connecting To The Rou
Back to Contents Page Cable Modem Connection NOTE: It is recommended that you install the Dell Wireless 2350 Broadband Router using the Setup Wizard provided on the Dell Wireless 2350 Broadband Router CD. Perform the steps below only when you are unable to install the Dell Wireless 2350 Broadband Router with the Setup Wizard. Cable Modem - Standard Setup Use this setup when your cable service provider does not require you to enter any information for your Internet broadband connection.
Broadband Router when you browse to http://my.router This configuration will work properly with a cable modem provider that does not require authentication. Back to Top Cable Modem with Name Settings 1. Connect the Ethernet port on the cable modem to the Internet port on the Dell Wireless 2350 Broadband Router through an Ethernet cable. 2. Connect any one of the four LAN ports on the Dell Wireless 2350 Broadband Router to the Ethernet port on your computer through another Ethernet cable. 3.
Back to Contents Page DSL Modem Connection NOTE: It is recommended that you install the Dell Wireless 2350 Broadband Router using the Setup Wizard provided on the Dell Wireless 2350 Broadband Router CD. Perform the steps below only when you are unable to install the Dell Wireless 2350 Broadband Router with the Setup Wizard.
Dell Wireless 2350 Broadband Router will allocated IP addresses to any connect computer automatically. · Default user name and password is admin. Use this to access the Configuration Settings on the Dell Wireless 2350 Broadband Router when you browse to http://my.router This configuration will work properly with a DSL provider that does not require authentication. Back to Top DSL with PPPoE 1.
Back to Contents Page Cable Modem with USB Connection A cable modem may support only Ethernet connection, only USB connection, or both types of connections. Cable Modem with only USB Connection Your Dell Wireless 2350 Broadband Router is designed to function with Ethernet connection only on its broadband interface. If your cable modem supports only a USB connection, you need to replace it with a model with at least one Ethernet connection.
Back to Contents Page Configuring Your Router as an Access Point for an Existing Network If you have an existing network, you may want to use your new router as an Access Point to extend the range of your network by allowing connection of more wireless and wired computers. You MUST turn off the DHCP server on the router if there is a DHCP server already in your network running to avoid IP address conflicts. To disable the DHCP server functions, follow the steps below: 1.
You will also need to allocate and setup a static IP address on your Dell Wireless 2350 Broadband Router. Perform the following steps to configure a static IP address: NOTE: The IP address that you use should be reserved by the DHCP server in your existing network. The router cannot act as a DHCP client and therefore, it needs a static IP address for its LAN interface. 1. Go to the Advanced Settings menu option tab on the top navigation bar and wait for the menu to appear. 2.
Back to Contents Page Configuring Your Dell™ Wireless 2350 Broadband Router for Gaming This section will assist in configuring the Dell Wireless 2350 Broadband Router router for gaming. In some cases, the firewall feature of the router will cause a game to not function as intended. This document will not provide details for each game, but will discuss how to open TCP/IP ports for one or more computers.
9. Reboot the client computer. The client computer will use the newly assigned IP and will not have any TCP/IP ports blocked by the firewall feature of the router.
Back to Contents Page Setting Wireless Encryption in Your Dell Wireless 2350 Broadband Router Without wireless security options configured in your network, an eavesdropper within your wireless range may be able to access the network and the data that is being transmitted over it. The Dell Wireless 2350 Broadband Router provides Wired Equivalent Privacy (WEP) and Wi-Fi Protected Access (WPA) encryption for wireless security. WPA is an upgrade to the WEP standard for securing your wireless network.
your router. 2. Choose a key format. This can be hexadecimal digits (0-9 and A-F) or ASCII characters (any key on the keyboard). 3. WPA Group Rekey Interval specifies how often the key “rotates” or changes. 4. WPA Encryption allows you to select one of two possible encryption methods—TKIP and AES. Choose one that your wireless clients support. 5. Click the NEXT button, and then click Save and Restart to apply the changes. 6. Set up the WPA on your wireless clients.
Back to Contents Page Turning Off Broadcast SSID 1. Log into the web configuration of your router at http://my.router, or the default address http://192.168.2.1. The Enter Network Password login prompt appears. 2. Type the following text in the user name and password fields: "admin". 3. Go to the Advanced Settings menu option tab on the top navigation bar and wait for the menu to appear. 4. Click the Advanced Wireless menu option in the drop down menu. 5. Check the Hide my wireless network checkbox. 6.
Back to Contents Page Setting Up File & Printer Sharing Installing File and Printer Sharing Sharing a printer Sharing files Installing the File & Printer Sharing Follow the instructions below to install the file and printer sharing service. For Windows 2000 and XP 1. Right-click the My Network Places icon (on the desktop in Windows 2000 and in the Start button menu in Windows XP) and left-click to select Properties in menu. 2. Right-click the Local Area Connection icon and select Properties in the menu.
6. Follow the on-screen instructions to complete. Sharing files You can share files on your computer so that users on other computers on your network can view them. 1. In Microsoft Windows Explorer, right-click on the file, folder, or drive letter you wish to share and left-click Sharing. 2. Click Share As. 3. Type a name for the share and follow the on-screen instructions to complete.
Back to Contents Page How To Setup Microsoft Windows XP Clients Connecting To The Router Depending on the service pack installed you have installed on your Windows XP operating the setup of the computer to connect to the Dell Wireless 2350 Broadband Router is different. To check what service pack is installed, follow these steps: 1. Click the Start button, and then click Control Panel. 2. If you are looking at the Category View of Control Panel, click Switch to Classic View. 3. Double-click System. 4.
Once you have determined what service pack is installed then follow on of the below sections How to Setup Microsoft Windows XP Clients without Service Pack 2 to Connect to the Router How to Setup Microsoft Windows XP Clients with Service Pack 2 to Connect to the Router How To Setup Microsoft Windows XP Clients with Service Pack 1 to Connect To The Router Configuring Automatic Network Connections To configure one or more wireless networks for auto connection, follow these steps: 1.
NOTE: For more information click Learn about setting up wireless network configuration. Enabling Encryption Because wireless networks transmit data using radio frequency transmission, other computers with wireless network adapters that are within range of your wireless broadband router can connect to your network. You can prevent unauthorized access to your wireless network by enabling encryption. When you enable encryption, you must specify a network encryption key.
How To Setup Microsoft Windows XP Clients with Service Pack 2 to Connect To The Router Configuring Automatic Network Connections Dell recommends using the Setup Wizard that is located on the Dell Wireless 2350 Broadband Router CD that cam with your device. To run the Setup Wizard, perform the following steps: 1. Insert the Dell Wireless 2350 Broadband Router Setup CD into the CD drive onto the computer you wish to connect wirelessly to the Dell Wireless 2350 Broadband Router.
Back to Contents Page Using Your Router: Dell™ Wireless 2350 Broadband Router User's Guide Overview Factory Default Settings Setup Wizard Control Utility Web-Based Configuration Tool Overview Factory Default Settings: Your Dell Wireless 2350 Broadband Router came with factory default settings that should work for the majority of the network usage scenarios. However, there are cases where your network environment may require a different router configuration.
Back to Contents Page Factory Default Settings: Dell™ Wireless 2350 Broadband Router User's Guide Dell pre-configures the Dell Wireless 2350 Broadband Router with the following settings: NOTE: If you lose track of the device settings, you can reset the router by pushing the reset button to restore these settings back to your router. Setting Default User Name admin Password admin Device Name Dell Wireless 2350 BroadBand router IP Address 192.168.2.1 Subnet Mask 255.255.255.
Back to Contents Page Setup Wizard: Dell™ Wireless 2350 Broadband Router User's Guide Introduction Launching the Setup Wizard Setup Wizard Screens Introduction The Setup Wizard is an easy-to-use program included on your Dell Wireless 2350 Broadband Router CD. It provides simplified configuration procedures for establishing Internet connectivity on the Dell Wireless 2350 Broadband Router.
Your CD should automatically launch the Setup Wizard. If it does not, complete the following steps to start the Wizard. a. Click the Start button, and then click Run. b. Type the following text in the Open: field: X:\setup.exe where X is the drive letter of your CD drive. Once the Setup Wizard has been launched, you will be guided through a series of windows. These windows are illustrated below along with an explanation on their functionalities.
· To begin Installing your Dell Wireless 2350 Broadband Router click Router Installation. The computer that is used to install the router should already be connected to the Internet via a cable or DSL modem. · To connect additional computers to your network after you have successfully installed the router using the Router Installation option, place the Dell Wireless 2350 Broadband Router CD in each additional computer and run the Setup Wizard.
Confirming the Internet Connection
If you are using a PPPoE (Point to Point Protocol over Ethernet) connection, your computer will then need to reboot. After rebooting, the Setup Wizard will run and display the below message. Click next to continue.
The next step is to reboot your modem. After rebooting the modem, click next to continue.
Connecting the Dell Wireless 2350 Broadband Router to Your Network Step 1 illustrates how to disconnect your cable/DSL modem from your computer.
Step 2 illustrates how to connect the cable/DSL modem to the Dell Wireless 2350 Broadband Router.
Step 3 illustrates how to connect the supplied Ethernet cable to your computer.
Step 4 illustrates how the Dell Wireless 2350 Broadband Router to your computer.
Step 5 illustrates how the Dell Wireless 2350 Broadband Router is connected to the power supply.
Step 6 illustrates how to verify that you have connected everything as outlined..
Configuring the Dell Wireless 2350 Broadband Router If you are using a PPPoE connection, type your PPPoE username and password in the boxes provided.
Select the type of Network your want to setup. Selecting the "Setup a Secure Router" will setup the Dell Wireless 2350 Broadband Router to use WEP to secure wireless connections. If you chose this option the your wireless clients will also need to use the same WEP settings. To setup a network that does not use encryption select "Setup a Non Secure Router" option. Follow the onscreen instruction for completing the settings..
The Setup Wizard will apply the Internet connection settings to your Dell Wireless 2350 Broadband Router when you have finished.
Congratulations You have successfully installed the Dell Wireless 2350 Broadband Router and configured the first computer for Internet access.
Back to Top Back to Contents Page
Back to Contents Page Control Utility: Dell™ Wireless 2350 Broadband Router User's Guide The Control Utility is Windows-based software that allows you to configure your router and monitor the status of the connection from your computer to the Dell Wireless 2350 Broadband Router and to the Internet.
The control utility program will run automatically upon each computer start-up by default. If the utility does not start automatically, run the Dell Wireless 2350 Broadband Router Dell Control Utility from the Start menu. Once running, a router icon is created in the system tray in the lower right corner of your screen. If you have a good connection to the Internet, the system tray icon looks gray and white utility panel. NOTE: .
Back to Contents Page Web-based Configuration Tool: Dell™ Wireless 2350 Broadband Router User's Guide Overview Basic Settings Advanced Settings Device Status System Tools Log Off Overview The web-based configuration tool enables you to set up advanced network configuration for your Dell Wireless 2350 Broadband Router. Follow the instructions below to gain access to the web tool. NOTE: Microsoft Internet Explorer 4.0 or higher or Netscape 4.0 or higher must be used for the web-based configuration tool.
Back to Top Log Off Select this option to log out of the web-based configuration. Press the Submit button to confirm that you want to log off. NOTE: The web-based configuration tool only allows access to one user at a time.
Back to Contents Page Technical Specifications and Regulatory Information: Dell™ Wireless 2350 Broadband Router User's Guide Technical Specifications Regulatory Information Limited Warranties and Return Policy Wireless Interoperability The Dell Wireless 2350 products are designed to be interoperable with any wireless LAN product that is based on direct sequence spread spectrum (DSSS) and orthogonal frequency division multiplexing (OFDM) radio technology and to comply with the following standards: IEEE 802
Power specification · Storage Temperature 0° to 70° C (32° F to 158° F) Receive Sensitivity · 11Mbps: 10-5 BER @ -80 dBm, typical · 54Mbps: 10-5 BER @ -65 dBm, typical Transmit Power · Up to 20 dBm DC power supply · Input: AC 100-250 50-60 Hz 1A · Output: 12V DC 0.5A for Power Supply D7658 5V DC 2A for Power Supply 2W850 Radio specificationRange: "Up to 100m" indoors and "Up to 450m" outdoors (open range) Frequency range: 2.4 - 2.
Utility Software · Setup Wizard software · Control Utility software Back to Top Regulatory Information The Dell Wireless 2350 wireless network device must be installed and used in strict accordance with the manufacturer's instructions as described in the user documentation that comes with the product. For country-specific approvals, see Radio approvals.
2446.6 MHz - 2483.5 MHz) There are few possibilities for outdoor use: On private property or on the private property of public persons, use is subject to a preliminary authorization procedure by the Ministry of Defence, with maximum authorized power of 100 mW in the 2446.5 2483.5 MHz band. Use outdoors on public property is not permitted. In the departments listed below, for the entire 2.
Interference statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy. If the equipment is not installed and used in accordance with the instructions, the equipment may cause harmful interference to radio communications.
What is not covered by this limited warranty? This limited warranty does not cover: • Software, including the operating system and software added to the Dell-branded hardware products through our factory-integration system, third-party software, or the reloading of software • Non-Dell-branded products and accessories • Problems that result from: - External causes such as accident, abuse, misuse, or problems with electrical power - Servicing not authorized by us - Usage that is not in accordance with product
Technical Support and Customer Service 1-800-822-8965 Government and Education Customers: Technical Support and Customer Service 1-800-234-1490 Dell-Branded Memory 1-888-363-5150 What will Dell do? During the first 90 days of the 90-day limited warranty and the first year of all other limited warranties: For the first 90 days of the 90-day limited warranty and the first year of all other limited warranties, we will repair any Dell-branded hardware products returned to us that prove to be defective in
Replacement parts and systems are covered for the remaining period of the limited warranty for the product you bought. What do I do if I am not satisfied? We pride ourselves on our great customer service. If you are not satisfied with the service you receive under this limited warranty, please let us know. We have found that the best way to resolve issues regarding our limited warranty is to work together.
Application software or an operating system that has been installed by Dell may not be returned unless you return the entire computer under the 21-day return policy, if applicable to your purchase (if not applicable to your purchase, you may not return application software or an operating system).
STATEMENT, FOR THE TERM OF THE WARRANTY PERIOD REFLECTED ON YOUR INVOICE. EXCEPT FOR THE EXPRESS WARRANTIES CONTAINED IN THIS WARRANTY STATEMENT, DELL DISCLAIMS ALL OTHER WARRANTIES AND CONDITIONS, EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION IMPLIED WARRANTIES AND CONDITIONS OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, STATUTORY OR OTHERWISE.
product is lost or damaged in shipment. We will return the repaired or replacement products to you. We will pay to ship the repaired or replaced products to you if you use an address in Canada. Otherwise, we will ship the product to you freight collect. If we determine that the problem is not covered under this warranty, we will notify you and inform you of service alternatives that are available to you on a fee basis .
(NAF) under its Code of Procedure then in effect (available via the Internet at www.arbforum.com, or via telephone at 1-800-474-2371). The arbitration will be limited solely to the dispute or controversy between you and Dell. Any award of the arbitrator(s) shall be final and binding on each of the parties, and may be entered as a judgment in any court of competent jurisdiction. Information may be obtained and claims may be filed with the NAF at P.O. Box 50191, Minneapolis, MN 55405.
While Dell offers a wide selection of software and peripheral products, we do not specifically test or guarantee that all of the products we offer work with any or all of the various models of Dell computers, nor do we test or guarantee all of the products we sell on the hundreds of different brands of computers available today. If you have questions about compatibility, we recommend and encourage you to contact the third-party software and peripheral product manufacturer or publisher directly.
above, and this Guarantee is given in place of all other guarantees whatsoever, to the fullest extent permitted by law. In the absence of applicable legislation, this Guarantee will be the end user's sole and exclusive remedy against Dell or any of its affiliates, and neither Dell nor any of its affiliates shall be liable for loss of profit or contracts, or any other indirect or consequential loss arising from negligence, breach of contract, or howsoever.
Access Point An Access Point is a device on the wireless network that receives and retransmits data. It allows computers with wireless network adapters to be connected, typically, to an Ethernet network. Cable Modem A cable modem is a device that enables you to hook up your computer to the Internet via a local cable TV line. Client A client is a computer on a network. Domain Name System (or Service) (DNS) DNS is an Internet service that translates domain names into IP addresses.
An Ethernet address is a unique, pre-programmed address, sometimes referred to as a media access control (MAC) address. Each computer on an Ethernet network has its own Ethernet address. This 12-digit hexadecimal address is encoded into the circuitry of the computer’s network adapter when it is manufactured. Other devices on the network use this address to identify the computer. This address is not the same as the IP address that is assigned to computers on TCP/IP networks.
NAT occurs when multiple IP addresses on a private LAN are converted to one public address. This public address is sent out to the Internet. NAT adds a level of security because the IP address for a computer connected to the private LAN is never transmitted to the Internet. NAT also allows xDSL/cable routers to be used with low-cost Internet accounts, where only one TCP/IP address is provided by the Internet service provider.
Wide Area Network (WAN) A WAN is a communications network that uses devices such as telephone lines, satellite dishes, or radio waves to span a larger geographic area than can be covered by a LAN. Wireless Local Area Network (WLAN) A WLAN is a type of Local Area Network (LAN) that uses high frequency radio waves rather than wires to communicate and transmit data among the network clients and devices.
Dell™ Wireless 2350 Broadband Router User's Guide Contents Introduction Overview Wireless Networking Overview A Look at the Hardware Installation and Configuration Cable Modem Connection DSL Modem Connection Cable Modem with USB Connection Configuring Your Dell Wireless 2350 Broadband Router as an Access Point for an Existing Network Configuring Your Dell Wireless 2350 Broadband Router for Gaming Setting Wireless Encryption in Your Router Turning Off Broadcast SSID Setting Up File and Printer Sharing How T
P/N Y6925 Revision A01, December 2004
Back to Contents Page Wireless Networking Overview: Dell™ Wireless 2350 Broadband Router User's Guide Wireless Local Area Network (WLAN) Identifying a WLAN Encryption Automatic Rate Selection and Rate Scaling Wireless Local Area Network (WLAN) A Local Area Network (LAN) is a network in one location. Computers at that location can share files, printers, and other services. In a LAN, a networked computer that requests services is called a client.
numbers, called an encryption key. Before transmitting information over the airwaves, the wireless client or access point encrypts or scrambles the information. The access point or wireless client receiving the information uses the same key to decrypt or unscramble the information. The information is only readable to WLAN devices that have the correct encryption key. The longer the key is, the stronger the encryption.
representing English characters as numbers, with each letter assigned a number from 0 to 127. For example, the ASCII code for uppercase M is 77. Most computers use ASCII codes to represent text, which makes it possible to transfer data from one computer to another. WPA WPA (Wi-Fi Protected Access) is an upgrade to the WEP standard for securing your wireless network. WPA is derived from and will be forward-compatible with the future IEEE 802.11i standard.
Back to Contents Page A Look at the Hardware: Dell™ Wireless 2350 Broadband Router User's Guide Front Panel Back Panel Front Panel The Dell Wireless 2350 Broadband Router has seven Light Emitting Diodes (LEDs), or link lights, on its front side. The following table defines the behaviour for each LED: Front Panel LED Represents Power Power Wireless Wireless LAN Activity The Power LED will light up green when the device is powered on. It will blink when the device is powering up or when it is reset.
Dell Wireless 2350 Broadband Router. Internet DSL or cable modem A steady green light indicates the connection is active (i.e. the Dell Wireless 2350 Broadband Router is connected to a xDSL or cable modem) and blinks with data activity. LAN LAN LAN LAN Local Area Network A steady green light indicates the connection is active and blinks with data activity.
Back to Contents Page
Back to Contents Page Introduction: Dell™ Wireless 2350 Broadband Router User's Guide Overview Wireless Networking Overview A Look at the Hardware Overview The Dell Wireless 2350 Broadband Router is an 802.11b/g wireless access point with a built-in Internet router. Connecting to a DSL or cable modem, the Dell Wireless 2350 Broadband Router can offer both wired and wireless computers simultaneous access to the Internet.
4-port Ethernet switch: Connects four wired computers for file and print sharing. Ethernet bridge: Enables file and print sharing between wired and wireless computers. In addition, connects to an Ethernet hub, extending Internet connectivity and sharing to more wired computers. The Dell Wireless 2350 Broadband Router supports up to 252 connect computers when used with additional router devices. Up to 16 of the 252 computers can be connected wirelessly.
Back to Contents Page Cable Modem Connection NOTE: It is recommended that you install the Dell Wireless 2350 Broadband Router using the Setup Wizard provided on the Dell Wireless 2350 Broadband Router CD. Perform the steps below only when you are unable to install the Dell Wireless 2350 Broadband Router with the Setup Wizard. Cable Modem - Standard Setup Use this setup when your cable service provider does not require you to enter any information for your Internet broadband connection.
Broadband Router when you browse to http://my.router This configuration will work properly with a cable modem provider that does not require authentication. Back to Top Cable Modem with Name Settings 1. Connect the Ethernet port on the cable modem to the Internet port on the Dell Wireless 2350 Broadband Router through an Ethernet cable. 2. Connect any one of the four LAN ports on the Dell Wireless 2350 Broadband Router to the Ethernet port on your computer through another Ethernet cable. 3.
Back to Contents Page DSL Modem Connection NOTE: It is recommended that you install the Dell Wireless 2350 Broadband Router using the Setup Wizard provided on the Dell Wireless 2350 Broadband Router CD. Perform the steps below only when you are unable to install the Dell Wireless 2350 Broadband Router with the Setup Wizard.
Dell Wireless 2350 Broadband Router will allocated IP addresses to any connect computer automatically. · Default user name and password is admin. Use this to access the Configuration Settings on the Dell Wireless 2350 Broadband Router when you browse to http://my.router This configuration will work properly with a DSL provider that does not require authentication. Back to Top DSL with PPPoE 1.
Back to Contents Page Cable Modem with USB Connection A cable modem may support only Ethernet connection, only USB connection, or both types of connections. Cable Modem with only USB Connection Your Dell Wireless 2350 Broadband Router is designed to function with Ethernet connection only on its broadband interface. If your cable modem supports only a USB connection, you need to replace it with a model with at least one Ethernet connection.
Back to Contents Page Configuring Your Router as an Access Point for an Existing Network If you have an existing network, you may want to use your new router as an Access Point to extend the range of your network by allowing connection of more wireless and wired computers. You MUST turn off the DHCP server on the router if there is a DHCP server already in your network running to avoid IP address conflicts. To disable the DHCP server functions, follow the steps below: 1.
You will also need to allocate and setup a static IP address on your Dell Wireless 2350 Broadband Router. Perform the following steps to configure a static IP address: NOTE: The IP address that you use should be reserved by the DHCP server in your existing network. The router cannot act as a DHCP client and therefore, it needs a static IP address for its LAN interface. 1. Go to the Advanced Settings menu option tab on the top navigation bar and wait for the menu to appear. 2.
Back to Contents Page Configuring Your Dell™ Wireless 2350 Broadband Router for Gaming This section will assist in configuring the Dell Wireless 2350 Broadband Router router for gaming. In some cases, the firewall feature of the router will cause a game to not function as intended. This document will not provide details for each game, but will discuss how to open TCP/IP ports for one or more computers.
9. Reboot the client computer. The client computer will use the newly assigned IP and will not have any TCP/IP ports blocked by the firewall feature of the router.
Back to Contents Page Setting Wireless Encryption in Your Dell Wireless 2350 Broadband Router Without wireless security options configured in your network, an eavesdropper within your wireless range may be able to access the network and the data that is being transmitted over it. The Dell Wireless 2350 Broadband Router provides Wired Equivalent Privacy (WEP) and Wi-Fi Protected Access (WPA) encryption for wireless security. WPA is an upgrade to the WEP standard for securing your wireless network.
your router. 2. Choose a key format. This can be hexadecimal digits (0-9 and A-F) or ASCII characters (any key on the keyboard). 3. WPA Group Rekey Interval specifies how often the key “rotates” or changes. 4. WPA Encryption allows you to select one of two possible encryption methods—TKIP and AES. Choose one that your wireless clients support. 5. Click the NEXT button, and then click Save and Restart to apply the changes. 6. Set up the WPA on your wireless clients.
Back to Contents Page Turning Off Broadcast SSID 1. Log into the web configuration of your router at http://my.router, or the default address http://192.168.2.1. The Enter Network Password login prompt appears. 2. Type the following text in the user name and password fields: "admin". 3. Go to the Advanced Settings menu option tab on the top navigation bar and wait for the menu to appear. 4. Click the Advanced Wireless menu option in the drop down menu. 5. Check the Hide my wireless network checkbox. 6.
Back to Contents Page Setting Up File & Printer Sharing Installing File and Printer Sharing Sharing a printer Sharing files Installing the File & Printer Sharing Follow the instructions below to install the file and printer sharing service. For Windows 2000 and XP 1. Right-click the My Network Places icon (on the desktop in Windows 2000 and in the Start button menu in Windows XP) and left-click to select Properties in menu. 2. Right-click the Local Area Connection icon and select Properties in the menu.
6. Follow the on-screen instructions to complete. Sharing files You can share files on your computer so that users on other computers on your network can view them. 1. In Microsoft Windows Explorer, right-click on the file, folder, or drive letter you wish to share and left-click Sharing. 2. Click Share As. 3. Type a name for the share and follow the on-screen instructions to complete.
Back to Contents Page How To Setup Microsoft Windows XP Clients Connecting To The Router Depending on the service pack installed you have installed on your Windows XP operating the setup of the computer to connect to the Dell Wireless 2350 Broadband Router is different. To check what service pack is installed, follow these steps: 1. Click the Start button, and then click Control Panel. 2. If you are looking at the Category View of Control Panel, click Switch to Classic View. 3. Double-click System. 4.
Once you have determined what service pack is installed then follow on of the below sections How to Setup Microsoft Windows XP Clients without Service Pack 2 to Connect to the Router How to Setup Microsoft Windows XP Clients with Service Pack 2 to Connect to the Router How To Setup Microsoft Windows XP Clients with Service Pack 1 to Connect To The Router Configuring Automatic Network Connections To configure one or more wireless networks for auto connection, follow these steps: 1.
NOTE: For more information click Learn about setting up wireless network configuration. Enabling Encryption Because wireless networks transmit data using radio frequency transmission, other computers with wireless network adapters that are within range of your wireless broadband router can connect to your network. You can prevent unauthorized access to your wireless network by enabling encryption. When you enable encryption, you must specify a network encryption key.
How To Setup Microsoft Windows XP Clients with Service Pack 2 to Connect To The Router Configuring Automatic Network Connections Dell recommends using the Setup Wizard that is located on the Dell Wireless 2350 Broadband Router CD that cam with your device. To run the Setup Wizard, perform the following steps: 1. Insert the Dell Wireless 2350 Broadband Router Setup CD into the CD drive onto the computer you wish to connect wirelessly to the Dell Wireless 2350 Broadband Router.
Back to Contents Page Installation and Configuration: Dell™ Wireless 2350 Broadband Router User's Guide Cable Modem Connection DSL Modem Connection Cable Modem with USB Connection Configuring Your Router as an Access Point for an Existing Network Configuring Your Dell Wireless 2350 Broadband Router for Gaming Setting Wireless Encryption in Your Dell Wireless 2350 Broadband Router Turning Off Broadcast SSID Setting Up File and Printer Sharing How To Setup Microsoft® Windows® XP Clients Connecting To The Rou
Back to Contents Page Advanced Settings: Dell™ Wireless 2350 Broadband Router User's Guide Advanced IP Settings DHCP Server Settings Time Zone Advanced Wireless Parental Control Advance Filtering DNS Server Status Dynamic DNS Access Control Settings Port Forwarding Settings Static Routing Administration Settings NOTE: Dell technical support representatives do not support the configuration options in the Advanced Settings portion of the configuration program.
Back to Top DHCP Server Settings Dynamic Host Configuration Protocol (DHCP), defines a way to automatically assign IP addresses to computers on a network. IP addresses are managed by a DHCP server. If a Windows computer is configured to obtain an IP address automatically, it automatically gets an address from the DHCP server.
Enable DHCP Server Functions By default, the Dell Wireless 2350 Broadband Router is set to function as a DHCP server. If you are installing the unit on an existing network that already has a DHCP server or simply do not want the Dell Wireless 2350 Broadband Router to function as the network's DHCP server, click to deselect Enable DHCP Server Functions to disable the DHCP server function.
Use the Time Zone page to select your local time zone from the pull-down list. The Time Zone Settings affect the Intruder Detection Log. This setting overrides the time stamp on IP packets that are in Greenwich Mean Time (GMT). During the summer months, the clock will move one or several hours ahead. Countries have different change dates. In most of the U.S and Canada, daylight saving time begins on the first Sunday of April. Time reverts to standard time on the last Sunday of October.
Enable Wireless This setting enables radio transmission and reception on the Dell Wireless 2350 Broadband Router. Hide my wireless network Checking this option disables the Dell Wireless 2350 Broadband Router sending out beacon packets to the wireless network. It is not selected by default and other users can easily find and make association to your Dell Wireless 2350 Broadband Router with the use of a site survey tool. If you want to increase wireless network security, you can enable this feature.
Beacon Interval The amount of time in Kusecs (one Kusec equals 1,024 microseconds) between radio beacons from the Dell Wireless 2350 Broadband Router to its client stations. The value range is from 1 to 65535. RTS Threshold This is the packet size above which the Dell Wireless 2350 Broadband Router will issue a Request to Send before sending the packet. RTS (Request to Send) mechanism prevents the Hidden Node problem.
5. Click the Submit button. The repeater AP must be located within the coverage of your root AP in order to associate with the root AP and extend it's coverage. NOTE:Ensure all Dell Wireless 2350 Broadband Routers are set to same wireless settings. To Configure your Dell Wireless 2350 Broadband Router back as a root AP: 1. Click the option Enable this AP as a Root AP 2. Click the Submit button.
Advanced Filtering allows user to setup a more complicated rule to filter out unwanted traffic. Click ADD button to setup source IP, Destination IP, IP protocol, TCP port, and UDP port. Once a rule has been setup then if there is a packet that is matched with the rules then it will be either accepted or dropped by Dell Wireless 2350 Broadband Router depending on the rule setting.
Users can register a domain name from dyndns.org. With this domain, it allows user enter the domain name instead of entering IP address. DDNS will map IP address to user’s domain name. Back to Top Access Control Settings The Access Control Settings feature allows you to control which local client computer can or can not access the network through the router. The Dell Wireless 2350 broadband Router by default allows any local client computer to access the network.
To enable access control in the router, perform the following steps: 1. Click to select Enable MAC Access Control. 2. Click the Add button, a pop-up window will open and then enter the MAC address of the network card on the computer on which you allow the access to the router. 3. Click Submit to enter the rule to the router. 4. To remove an existing rule, click to select edit beside MAC address. 5. A pop-up window will open and click the Delete button to remove it.
DMZ The DMZ (demilitarized zone) feature allows access to all ports. (For example, if you have problems hosting a game server, you can choose this option. This will open all ports to your game server.) 1. Click to select Enable DMZ Host . 2. Type the IP address of the computer that you want to run the gaming application in the DMZ IP Address field. 3. Click the Submit button to activate the setting.
7. In the Port type field, select TCP, UDP, or both protocols. The protocol could be specified in your application's documentation. 8. Click the Submit button to activate the setting. For example, if you want to play the game Fighter Ace II on a computer with an IP address of 192.168.2.3, enter 3 for the Destination IP Address. Select TCP as the Port type. Enter 50000 and 51000 for two fields of Incoming Ports and also for the Destination Port. Click Submit button to activate the setting.
Static routes are manually configured routes to remote networks. That is, the route is predefined and is not discovered by the Routing Information Protocol (RIP), as in dynamic routing. Static routing allows you to assign a gateway to an IP address or network. If there are routers on your internal network that do not function with RIP 1 or 2, you can set up a static route to those routers.
If you have an Windows XP system, you can use it to access and control the router while the router's UPnP function is enabled. Here are some examples of what you can do with UPnP from your Windows XP system. Example 1: Access the router's web configuration tool without knowing its IP address. 1. Double-click the My Network Neighborhood icon from the desktop. 2. Double-click the Broadband Router icon that is created for your router.
8. Click Add. 9. Type Description of service, IP address of the service host, External Port number for this service, Internal Port number for this service, and click to select either TCP or UDP. For example, the graph below shows an example of how to enable a computer with an IP address 192.168.2.101 to host a public HTTP server. Service Settings 10. Click the OK button to save the changes.
Back to Contents Page How to Configure the Dell Wireless 2350 Broadband Router using the Control Utility: Dell™ Wireless 2350 Broadband Router User's Guide My Network Overview Wireless Settings Network Access Control Gaming Remote Access Administration Diagnostics Advanced Settings My Network Overview This screen provides information about your network connection and settings. The left pane displays your connection status.
Back to Top Wireless Settings · Network Name (SSID) The SSID is a unique network name. It is used to identify the WLAN. This name is used when connecting additional computers to your wireless router. · Channel This is the radio channel over which a communication transmission occurs. · Default Settings Resets the Dell Wireless 2350 Broadband Router to its factory defaults. · Apply Saves current settings. · Restore Restores previous settings.
WEP Settings Wired Equivalent Privacy (WEP) encryption is used in the 802.11 standard is to protect wireless communication from eavesdropping. WEP provides a way of creating an encrypted key that is shared between a wireless client (such as a notebook with a wireless PC card) and the router. This key encrypts data before it is transmitted. WEP can be implemented with a 40(64)-bit or 104(128)-bit key. For added security, change your key often.
WPA Settings Wi-Fi Protected Access (WPA) is an upgrade to the WEP standard for securing your wireless network. If you would like to secure your wireless network using WPA, you must have WPA support for your wireless clients. If you are using a Dell wireless client, you can check for the availability of WPA-enabled software updates for your wireless client at http://support.dell.com. · WPA Pre-shared Key All wireless clients must use this key to gain access to the network.
· Add This adds a new Parental Control entry to the list. · Edit Allows you to edit any current entry. · Delete Deletes am entry from the Parental Control list.. · Delete All Deletes all records from the Parental Control list. · Restore Restores previous settings. Network Access Control Parental Control Parental Control allows you to determine what type of websites are accessible through your wireless network.
5. Select Allow or Deny for web access. 6. Specify which websites may be accessed or may not be accessed by entering their URLs in the Website URL field. 7. Click the OK button to apply you settings, or click the Cancel button to exit without making any changes. 8. Click the Apply Parental Control Settings button on the bottom of the screen to activate the new settings.
DMZ Some applications experience problems when working behind a firewall. To solve this problem you can put computers outside of the firewall via the router's DMZ (demilitarized zone) feature. The DMZ feature disables the NAT firewall and allows all data to pass through all ports to this computer. Follow the instructions below to enable the DMZ feature. 1. Click to select Enable DMZ Host. 2. Type the IP address of the computer that will run the gaming application in the DMZ IP Address field. 3.
5. Enter the incoming port number in the Incoming Port No. field and the outgoing port number in the Outgoing Port No. (also called Destination Port) field. 6. Select Enable or Disable the gaming from the State list. 7. Click the OK button to apply, or click the Cancel button to exit without making any changes. Back to Top Remote Access Remote Access Allow Remote User to Configure the Device This option allows you to configure the device from a remote location via the network. 1.
1. If you want your WAN port to be visible on the Internet, click to select Allow remote user to ping the device. 2. Click the Apply button to save the settings, or click the Restore button to restore to its previous settings. Back to Top Administration Administration System Rescue System Rescue allows you to reset your Dell Wireless 2350 Broadband Router. You can also save or load a backup of your configuration settings.
1. Click the Change the Router Password button. The Password Settings window appears. 2. Type the original password in the Original Password field. 3. Type the new password in the New Password field, and then retype it in the Confirm Password field to verify. 4. Type the password hint message in the Password Hint Message field. 5. Click the Submit button when you finish the setting. If you want to clear any values you have entered in any field, click the Cancel button.
Advanced Settings Advanced Settings To configure the advanced settings of the router, click the Login button to log in to the web-based configuration tool. Your Internet browser will open and you will be logged into the Dell Wireless 2350 Broadband Router's web-based configuration tool. The web-based configuration tool allows you to set up advanced network configurations for your Dell Wireless 2350 Broadband Router. Refer to the section Web-Based Configuration Tool for detailed information.
Back to Contents Page Factory Default Settings: Dell™ Wireless 2350 Broadband Router User's Guide Dell pre-configures the Dell Wireless 2350 Broadband Router with the following settings: NOTE: If you lose track of the device settings, you can reset the router by pushing the reset button to restore these settings back to your router. Setting Default User Name admin Password admin Device Name Dell Wireless 2350 BroadBand router IP Address 192.168.2.1 Subnet Mask 255.255.255.
Back to Contents Page Setup Wizard: Dell™ Wireless 2350 Broadband Router User's Guide Introduction Launching the Setup Wizard Setup Wizard Screens Introduction The Setup Wizard is an easy-to-use program included on your Dell Wireless 2350 Broadband Router CD. It provides simplified configuration procedures for establishing Internet connectivity on the Dell Wireless 2350 Broadband Router.
Your CD should automatically launch the Setup Wizard. If it does not, complete the following steps to start the Wizard. a. Click the Start button, and then click Run. b. Type the following text in the Open: field: X:\setup.exe where X is the drive letter of your CD drive. Once the Setup Wizard has been launched, you will be guided through a series of windows. These windows are illustrated below along with an explanation on their functionalities.
· To begin Installing your Dell Wireless 2350 Broadband Router click Router Installation. The computer that is used to install the router should already be connected to the Internet via a cable or DSL modem. · To connect additional computers to your network after you have successfully installed the router using the Router Installation option, place the Dell Wireless 2350 Broadband Router CD in each additional computer and run the Setup Wizard.
Confirming the Internet Connection
If you are using a PPPoE (Point to Point Protocol over Ethernet) connection, your computer will then need to reboot. After rebooting, the Setup Wizard will run and display the below message. Click next to continue.
The next step is to reboot your modem. After rebooting the modem, click next to continue.
Connecting the Dell Wireless 2350 Broadband Router to Your Network Step 1 illustrates how to disconnect your cable/DSL modem from your computer.
Step 2 illustrates how to connect the cable/DSL modem to the Dell Wireless 2350 Broadband Router.
Step 3 illustrates how to connect the supplied Ethernet cable to your computer.
Step 4 illustrates how the Dell Wireless 2350 Broadband Router to your computer.
Step 5 illustrates how the Dell Wireless 2350 Broadband Router is connected to the power supply.
Step 6 illustrates how to verify that you have connected everything as outlined..
Configuring the Dell Wireless 2350 Broadband Router If you are using a PPPoE connection, type your PPPoE username and password in the boxes provided.
Select the type of Network your want to setup. Selecting the "Setup a Secure Router" will setup the Dell Wireless 2350 Broadband Router to use WEP to secure wireless connections. If you chose this option the your wireless clients will also need to use the same WEP settings. To setup a network that does not use encryption select "Setup a Non Secure Router" option. Follow the onscreen instruction for completing the settings..
The Setup Wizard will apply the Internet connection settings to your Dell Wireless 2350 Broadband Router when you have finished.
Congratulations You have successfully installed the Dell Wireless 2350 Broadband Router and configured the first computer for Internet access.
Back to Top Back to Contents Page
Back to Contents Page Control Utility: Dell™ Wireless 2350 Broadband Router User's Guide The Control Utility is Windows-based software that allows you to configure your router and monitor the status of the connection from your computer to the Dell Wireless 2350 Broadband Router and to the Internet.
The control utility program will run automatically upon each computer start-up by default. If the utility does not start automatically, run the Dell Wireless 2350 Broadband Router Dell Control Utility from the Start menu. Once running, a router icon is created in the system tray in the lower right corner of your screen. If you have a good connection to the Internet, the system tray icon looks gray and white utility panel. NOTE: .
Back to Contents Page Web-based Configuration Tool: Dell™ Wireless 2350 Broadband Router User's Guide Overview Basic Settings Advanced Settings Device Status System Tools Log Off Overview The web-based configuration tool enables you to set up advanced network configuration for your Dell Wireless 2350 Broadband Router. Follow the instructions below to gain access to the web tool. NOTE: Microsoft Internet Explorer 4.0 or higher or Netscape 4.0 or higher must be used for the web-based configuration tool.
Back to Top Log Off Select this option to log out of the web-based configuration. Press the Submit button to confirm that you want to log off. NOTE: The web-based configuration tool only allows access to one user at a time.
Back to Contents Page Using Your Router: Dell™ Wireless 2350 Broadband Router User's Guide Overview Factory Default Settings Setup Wizard Control Utility Web-Based Configuration Tool Overview Factory Default Settings: Your Dell Wireless 2350 Broadband Router came with factory default settings that should work for the majority of the network usage scenarios. However, there are cases where your network environment may require a different router configuration.
Back to Contents Page Basic Settings: Dell™ Wireless 2350 Broadband Router User's Guide The following configuration options are included in Basic Settings: Router Mode Wireless Settings Wireless Security Internet Connection Settings Save & Apply NOTE: To implement the changes you make to the settings, you must save your settings and restart the router. Otherwise, the router uses the previous settings.
devices in an existing network. All wired and wireless devices are located in the same Class C IP subnet (e.g. 255.255.255.0). The Internet port on the Dell Wireless 2350 Broadband Router is not used in this mode. NOTE: If the device is put in AP mode, the Internet Connection Settings will not be available. The Gateway mode is the default setting in Dell Wireless 2350 Broadband Router.
Wireless Security Data encryption provides added security by encoding network communications using an encryption key. Your Dell Wireless 2350 Broadband Router, in conjunction with wireless network adapters that support encryption, can scramble your transmitted data to make it difficult for someone to eavesdrop or intercept your information. Two methods of data encryption are available: Wired Equivalent Privacy (WEP) and Wi-Fi Protected Access (WPA).
If you choose 40(64)-bit encryption, enter a 5-character (or 10 hexadecimal digits) WEP encryption Key in the fields provided. For 104(128)-bit encryption, enter a 13-character (or 26 hexadecimal digits) WEP key in the fields provided. You have the option of entering four different keys to store on the Dell Wireless 2350 Broadband Router. Select only one key out of the four provided in the Default Key drop-down list. For added security, change your key often.
Your ISP Requires You to Input WAN Ethernet MAC If your ISP requires that you input a WAN Ethernet MAC address, click to select Your ISP requires you to input WAN Ethernet MAC. In the field provided, type the public WAN (cable/DSL) MAC address assigned to your Dell Wireless 2350 Broadband Router. You can find the WAN MAC address on the back panel of the Dell Wireless 2350 Broadband Router or on the Device Information page in the web-based configuration tool.
Save & Apply Use the Save & Apply page to submit all the network setting changes you have made. Click the Save & Restart button to update the network configurations for your Dell Wireless 2350 Broadband Router. New settings are written to the firmware, and the Dell Wireless 2350 Broadband Router reboots automatically. NOTE: If you have wireless clients in your network, you must configure the clients' wireless network cards to match the settings for the Dell Wireless 2350 Broadband Router.
Back to Contents Page Advanced Settings: Dell™ Wireless 2350 Broadband Router User's Guide Advanced IP Settings DHCP Server Settings Time Zone Advanced Wireless Parental Control Advance Filtering DNS Server Status Dynamic DNS Access Control Settings Port Forwarding Settings Static Routing Administration Settings NOTE: Dell technical support representatives do not support the configuration options in the Advanced Settings portion of the configuration program.
Back to Top DHCP Server Settings Dynamic Host Configuration Protocol (DHCP), defines a way to automatically assign IP addresses to computers on a network. IP addresses are managed by a DHCP server. If a Windows computer is configured to obtain an IP address automatically, it automatically gets an address from the DHCP server.
Enable DHCP Server Functions By default, the Dell Wireless 2350 Broadband Router is set to function as a DHCP server. If you are installing the unit on an existing network that already has a DHCP server or simply do not want the Dell Wireless 2350 Broadband Router to function as the network's DHCP server, click to deselect Enable DHCP Server Functions to disable the DHCP server function.
Use the Time Zone page to select your local time zone from the pull-down list. The Time Zone Settings affect the Intruder Detection Log. This setting overrides the time stamp on IP packets that are in Greenwich Mean Time (GMT). During the summer months, the clock will move one or several hours ahead. Countries have different change dates. In most of the U.S and Canada, daylight saving time begins on the first Sunday of April. Time reverts to standard time on the last Sunday of October.
Enable Wireless This setting enables radio transmission and reception on the Dell Wireless 2350 Broadband Router. Hide my wireless network Checking this option disables the Dell Wireless 2350 Broadband Router sending out beacon packets to the wireless network. It is not selected by default and other users can easily find and make association to your Dell Wireless 2350 Broadband Router with the use of a site survey tool. If you want to increase wireless network security, you can enable this feature.
Beacon Interval The amount of time in Kusecs (one Kusec equals 1,024 microseconds) between radio beacons from the Dell Wireless 2350 Broadband Router to its client stations. The value range is from 1 to 65535. RTS Threshold This is the packet size above which the Dell Wireless 2350 Broadband Router will issue a Request to Send before sending the packet. RTS (Request to Send) mechanism prevents the Hidden Node problem.
5. Click the Submit button. The repeater AP must be located within the coverage of your root AP in order to associate with the root AP and extend it's coverage. NOTE:Ensure all Dell Wireless 2350 Broadband Routers are set to same wireless settings. To Configure your Dell Wireless 2350 Broadband Router back as a root AP: 1. Click the option Enable this AP as a Root AP 2. Click the Submit button.
Advanced Filtering allows user to setup a more complicated rule to filter out unwanted traffic. Click ADD button to setup source IP, Destination IP, IP protocol, TCP port, and UDP port. Once a rule has been setup then if there is a packet that is matched with the rules then it will be either accepted or dropped by Dell Wireless 2350 Broadband Router depending on the rule setting.
Users can register a domain name from dyndns.org. With this domain, it allows user enter the domain name instead of entering IP address. DDNS will map IP address to user’s domain name. Back to Top Access Control Settings The Access Control Settings feature allows you to control which local client computer can or can not access the network through the router. The Dell Wireless 2350 broadband Router by default allows any local client computer to access the network.
To enable access control in the router, perform the following steps: 1. Click to select Enable MAC Access Control. 2. Click the Add button, a pop-up window will open and then enter the MAC address of the network card on the computer on which you allow the access to the router. 3. Click Submit to enter the rule to the router. 4. To remove an existing rule, click to select edit beside MAC address. 5. A pop-up window will open and click the Delete button to remove it.
DMZ The DMZ (demilitarized zone) feature allows access to all ports. (For example, if you have problems hosting a game server, you can choose this option. This will open all ports to your game server.) 1. Click to select Enable DMZ Host . 2. Type the IP address of the computer that you want to run the gaming application in the DMZ IP Address field. 3. Click the Submit button to activate the setting.
7. In the Port type field, select TCP, UDP, or both protocols. The protocol could be specified in your application's documentation. 8. Click the Submit button to activate the setting. For example, if you want to play the game Fighter Ace II on a computer with an IP address of 192.168.2.3, enter 3 for the Destination IP Address. Select TCP as the Port type. Enter 50000 and 51000 for two fields of Incoming Ports and also for the Destination Port. Click Submit button to activate the setting.
Static routes are manually configured routes to remote networks. That is, the route is predefined and is not discovered by the Routing Information Protocol (RIP), as in dynamic routing. Static routing allows you to assign a gateway to an IP address or network. If there are routers on your internal network that do not function with RIP 1 or 2, you can set up a static route to those routers.
If you have an Windows XP system, you can use it to access and control the router while the router's UPnP function is enabled. Here are some examples of what you can do with UPnP from your Windows XP system. Example 1: Access the router's web configuration tool without knowing its IP address. 1. Double-click the My Network Neighborhood icon from the desktop. 2. Double-click the Broadband Router icon that is created for your router.
8. Click Add. 9. Type Description of service, IP address of the service host, External Port number for this service, Internal Port number for this service, and click to select either TCP or UDP. For example, the graph below shows an example of how to enable a computer with an IP address 192.168.2.101 to host a public HTTP server. Service Settings 10. Click the OK button to save the changes.
Back to Contents Page Device Status: Dell™ Wireless 2350 Broadband Router User's Guide The Device Status screen displays the basic network settings for your Dell Wireless 2350 Wireless Broadband Router. When changes are made to the network settings, those changes are updated on this screen. In addition, it graphically displays the current connection status for the Dell Wireless 2350 Broadband Router and other devices in your network. Connections between network devices are shown with a yellow arrow.
An active connection indicates the WAN interface of the router has a valid IP address and your computers can connect to the Internet via the router. Wired Client (LAN) Shown as an active connection when a wired client is configured and physically connected to your network, and inactive when the Ethernet cable is disconnected from the computer.
Back to Contents Page System Tools: Dell™ Wireless 2350 Broadband Router User's Guide Use the System Tools section to view the intruder detection log, routing tables, and system diagnostics regarding the device settings and status. The System Tools section also includes features to restore the default settings, upgrade the firmware for the Dell Wireless 2350 Broadband Router and reset the unit.
Time Based on the timestamp of the IP packet, plus or minus the time offset Event Type of attack that the router detects Event Type Type of attack that the router detects Details Details about the detected attack The system can alert you via e-mail to any attempted intrusion. 1. Click to select Email Alert Enable. 2. Type the e-mail address that you want the alert sent to in the Email Address field. 3. Click the Submit button.
To enable logging information click on Yes. This will allow user to record internet transmit and receive traffic information which will be displayed on this page. Back to Top Import/Export Settings Import/Export Settings The Dell Wireless 2350 Broadband Router allows the user to save the current settings onto storage devices and to load previous saved settings back into the router. Click the Export button to export the current settings to a .pro file.
The figure above shows system statistics for all wired and wireless stations.
Type The type of routing. This can be either of the following: LAN or WAN interface (INTF) Static routing Destination LAN IP Address Either an entire network or a specific IP address. An IP address ending in .0 refers to a network. Subnet Mask Must follow the IP subnet mask rules Gateway IP Address To communicate with an IP address matching the destination IP Address, the Dell Wireless 2350 Broadband Router sends all traffic through the gateway IP address listed here.
The Systems Diagnostic page is for your information only. This page displays both the configuration settings and diagnostics for the Dell Wireless 2350 Broadband Router. Configuration settings include firmware version, the ISP and device settings that have been configured for your network. The Diagnostic section shows the current connections for your network. Diagnostic settings include the ISP status, link status, current WAN connection, LAN MAC table, and WAN MAC table.
The Load Default Settings page allows you to reload the factory default configurations that came with the device. When this option is used, the default IP address is reset to the factory default value (192.168.2.1). This is equivalent to pressing and holding the Reset button on the back panel of the device for more than 5 seconds (for more details, refer to A Look at the Hardware).
Dell periodically releases firmware updates to provide improved performance or capabilities. There are two methods to upgrade you firmware. The first method is to check the Dell support website, http://support.dell.com, to see if there are any new upgrades. Download the new firmware first before upgrading and save it to one of the clients in your network. To upgrade the firmware, type the firmware file path into the box, or click the Browse button to choose a firmware file to upgrade to.
Broadband Router, the home page will be loaded automatically. While the Wireless 2350 resets, the Power light on the front panel of the router blinks. NOTE: You must be connected to the Internet to check for firmware updates NOTE: Dell does not recommend upgrading the Dell Wireless 2350 Broadband Router from a wireless client. Dell recommends connecting to your Dell Wireless Router with a LAN cable connection to perform your firmware upgrades.
Back to Contents Page How to Configure the Dell Wireless 2350 Broadband Router using the Control Utility: Dell™ Wireless 2350 Broadband Router User's Guide My Network Overview Wireless Settings Network Access Control Gaming Remote Access Administration Diagnostics Advanced Settings My Network Overview This screen provides information about your network connection and settings. The left pane displays your connection status.
Back to Top Wireless Settings · Network Name (SSID) The SSID is a unique network name. It is used to identify the WLAN. This name is used when connecting additional computers to your wireless router. · Channel This is the radio channel over which a communication transmission occurs. · Default Settings Resets the Dell Wireless 2350 Broadband Router to its factory defaults. · Apply Saves current settings. · Restore Restores previous settings.
WEP Settings Wired Equivalent Privacy (WEP) encryption is used in the 802.11 standard is to protect wireless communication from eavesdropping. WEP provides a way of creating an encrypted key that is shared between a wireless client (such as a notebook with a wireless PC card) and the router. This key encrypts data before it is transmitted. WEP can be implemented with a 40(64)-bit or 104(128)-bit key. For added security, change your key often.
WPA Settings Wi-Fi Protected Access (WPA) is an upgrade to the WEP standard for securing your wireless network. If you would like to secure your wireless network using WPA, you must have WPA support for your wireless clients. If you are using a Dell wireless client, you can check for the availability of WPA-enabled software updates for your wireless client at http://support.dell.com. · WPA Pre-shared Key All wireless clients must use this key to gain access to the network.
· Add This adds a new Parental Control entry to the list. · Edit Allows you to edit any current entry. · Delete Deletes am entry from the Parental Control list.. · Delete All Deletes all records from the Parental Control list. · Restore Restores previous settings. Network Access Control Parental Control Parental Control allows you to determine what type of websites are accessible through your wireless network.
5. Select Allow or Deny for web access. 6. Specify which websites may be accessed or may not be accessed by entering their URLs in the Website URL field. 7. Click the OK button to apply you settings, or click the Cancel button to exit without making any changes. 8. Click the Apply Parental Control Settings button on the bottom of the screen to activate the new settings.
DMZ Some applications experience problems when working behind a firewall. To solve this problem you can put computers outside of the firewall via the router's DMZ (demilitarized zone) feature. The DMZ feature disables the NAT firewall and allows all data to pass through all ports to this computer. Follow the instructions below to enable the DMZ feature. 1. Click to select Enable DMZ Host. 2. Type the IP address of the computer that will run the gaming application in the DMZ IP Address field. 3.
5. Enter the incoming port number in the Incoming Port No. field and the outgoing port number in the Outgoing Port No. (also called Destination Port) field. 6. Select Enable or Disable the gaming from the State list. 7. Click the OK button to apply, or click the Cancel button to exit without making any changes. Back to Top Remote Access Remote Access Allow Remote User to Configure the Device This option allows you to configure the device from a remote location via the network. 1.
1. If you want your WAN port to be visible on the Internet, click to select Allow remote user to ping the device. 2. Click the Apply button to save the settings, or click the Restore button to restore to its previous settings. Back to Top Administration Administration System Rescue System Rescue allows you to reset your Dell Wireless 2350 Broadband Router. You can also save or load a backup of your configuration settings.
1. Click the Change the Router Password button. The Password Settings window appears. 2. Type the original password in the Original Password field. 3. Type the new password in the New Password field, and then retype it in the Confirm Password field to verify. 4. Type the password hint message in the Password Hint Message field. 5. Click the Submit button when you finish the setting. If you want to clear any values you have entered in any field, click the Cancel button.
Advanced Settings Advanced Settings To configure the advanced settings of the router, click the Login button to log in to the web-based configuration tool. Your Internet browser will open and you will be logged into the Dell Wireless 2350 Broadband Router's web-based configuration tool. The web-based configuration tool allows you to set up advanced network configurations for your Dell Wireless 2350 Broadband Router. Refer to the section Web-Based Configuration Tool for detailed information.
Back to Contents Page Basic Settings: Dell™ Wireless 2350 Broadband Router User's Guide The following configuration options are included in Basic Settings: Router Mode Wireless Settings Wireless Security Internet Connection Settings Save & Apply NOTE: To implement the changes you make to the settings, you must save your settings and restart the router. Otherwise, the router uses the previous settings.
devices in an existing network. All wired and wireless devices are located in the same Class C IP subnet (e.g. 255.255.255.0). The Internet port on the Dell Wireless 2350 Broadband Router is not used in this mode. NOTE: If the device is put in AP mode, the Internet Connection Settings will not be available. The Gateway mode is the default setting in Dell Wireless 2350 Broadband Router.
Wireless Security Data encryption provides added security by encoding network communications using an encryption key. Your Dell Wireless 2350 Broadband Router, in conjunction with wireless network adapters that support encryption, can scramble your transmitted data to make it difficult for someone to eavesdrop or intercept your information. Two methods of data encryption are available: Wired Equivalent Privacy (WEP) and Wi-Fi Protected Access (WPA).
If you choose 40(64)-bit encryption, enter a 5-character (or 10 hexadecimal digits) WEP encryption Key in the fields provided. For 104(128)-bit encryption, enter a 13-character (or 26 hexadecimal digits) WEP key in the fields provided. You have the option of entering four different keys to store on the Dell Wireless 2350 Broadband Router. Select only one key out of the four provided in the Default Key drop-down list. For added security, change your key often.
Your ISP Requires You to Input WAN Ethernet MAC If your ISP requires that you input a WAN Ethernet MAC address, click to select Your ISP requires you to input WAN Ethernet MAC. In the field provided, type the public WAN (cable/DSL) MAC address assigned to your Dell Wireless 2350 Broadband Router. You can find the WAN MAC address on the back panel of the Dell Wireless 2350 Broadband Router or on the Device Information page in the web-based configuration tool.
Save & Apply Use the Save & Apply page to submit all the network setting changes you have made. Click the Save & Restart button to update the network configurations for your Dell Wireless 2350 Broadband Router. New settings are written to the firmware, and the Dell Wireless 2350 Broadband Router reboots automatically. NOTE: If you have wireless clients in your network, you must configure the clients' wireless network cards to match the settings for the Dell Wireless 2350 Broadband Router.
Back to Contents Page Device Status: Dell™ Wireless 2350 Broadband Router User's Guide The Device Status screen displays the basic network settings for your Dell Wireless 2350 Wireless Broadband Router. When changes are made to the network settings, those changes are updated on this screen. In addition, it graphically displays the current connection status for the Dell Wireless 2350 Broadband Router and other devices in your network. Connections between network devices are shown with a yellow arrow.
An active connection indicates the WAN interface of the router has a valid IP address and your computers can connect to the Internet via the router. Wired Client (LAN) Shown as an active connection when a wired client is configured and physically connected to your network, and inactive when the Ethernet cable is disconnected from the computer.
Back to Contents Page System Tools: Dell™ Wireless 2350 Broadband Router User's Guide Use the System Tools section to view the intruder detection log, routing tables, and system diagnostics regarding the device settings and status. The System Tools section also includes features to restore the default settings, upgrade the firmware for the Dell Wireless 2350 Broadband Router and reset the unit.
Time Based on the timestamp of the IP packet, plus or minus the time offset Event Type of attack that the router detects Event Type Type of attack that the router detects Details Details about the detected attack The system can alert you via e-mail to any attempted intrusion. 1. Click to select Email Alert Enable. 2. Type the e-mail address that you want the alert sent to in the Email Address field. 3. Click the Submit button.
To enable logging information click on Yes. This will allow user to record internet transmit and receive traffic information which will be displayed on this page. Back to Top Import/Export Settings Import/Export Settings The Dell Wireless 2350 Broadband Router allows the user to save the current settings onto storage devices and to load previous saved settings back into the router. Click the Export button to export the current settings to a .pro file.
The figure above shows system statistics for all wired and wireless stations.
Type The type of routing. This can be either of the following: LAN or WAN interface (INTF) Static routing Destination LAN IP Address Either an entire network or a specific IP address. An IP address ending in .0 refers to a network. Subnet Mask Must follow the IP subnet mask rules Gateway IP Address To communicate with an IP address matching the destination IP Address, the Dell Wireless 2350 Broadband Router sends all traffic through the gateway IP address listed here.
The Systems Diagnostic page is for your information only. This page displays both the configuration settings and diagnostics for the Dell Wireless 2350 Broadband Router. Configuration settings include firmware version, the ISP and device settings that have been configured for your network. The Diagnostic section shows the current connections for your network. Diagnostic settings include the ISP status, link status, current WAN connection, LAN MAC table, and WAN MAC table.
The Load Default Settings page allows you to reload the factory default configurations that came with the device. When this option is used, the default IP address is reset to the factory default value (192.168.2.1). This is equivalent to pressing and holding the Reset button on the back panel of the device for more than 5 seconds (for more details, refer to A Look at the Hardware).
Dell periodically releases firmware updates to provide improved performance or capabilities. There are two methods to upgrade you firmware. The first method is to check the Dell support website, http://support.dell.com, to see if there are any new upgrades. Download the new firmware first before upgrading and save it to one of the clients in your network. To upgrade the firmware, type the firmware file path into the box, or click the Browse button to choose a firmware file to upgrade to.
Broadband Router, the home page will be loaded automatically. While the Wireless 2350 resets, the Power light on the front panel of the router blinks. NOTE: You must be connected to the Internet to check for firmware updates NOTE: Dell does not recommend upgrading the Dell Wireless 2350 Broadband Router from a wireless client. Dell recommends connecting to your Dell Wireless Router with a LAN cable connection to perform your firmware upgrades.
Back to Contents Page A Look at the Hardware: Dell™ Wireless 2350 Broadband Router User's Guide Front Panel Back Panel Front Panel The Dell Wireless 2350 Broadband Router has seven Light Emitting Diodes (LEDs), or link lights, on its front side. The following table defines the behaviour for each LED: Front Panel LED Represents Power Power Wireless Wireless LAN Activity The Power LED will light up green when the device is powered on. It will blink when the device is powering up or when it is reset.
Dell Wireless 2350 Broadband Router. Internet DSL or cable modem A steady green light indicates the connection is active (i.e. the Dell Wireless 2350 Broadband Router is connected to a xDSL or cable modem) and blinks with data activity. LAN LAN LAN LAN Local Area Network A steady green light indicates the connection is active and blinks with data activity.
Back to Contents Page
