Alienware AW2518HF 모니터 사용자 가이드 모델 : AW2518HF 규정 모델 : AW2518HFb
참고 , 주의 및 경고 참고 : 컴퓨터를 더 잘 사용할 수 있도록 돕는 중요한 정보를 나타냅니다 . 주의 : 지침을 따르지 않을 경우 잠재적인 하드웨어 손상이나 데이터 손실을 알리는 주의가 표시됩니다 . 경고 : 경고는 물적 손해 , 신체 상해 또는 사망 가능성이 있음을 나타냅니다 . Copyright © 2017-2019 Dell Inc. All rights reserved. 이 제품은 미국 및 국제 저작권과 지적 재산권 법률에 의해 보호됩니다 . Dell ™ 및 Dell 로고는 미국 및 / 또는 기타 관할지에서 Dell Inc. 의 상표입 니다 . 여기에 언급된 기타 모든 마크 및 이름은 각각 해당 회사의 상표입니다 . 2019 - 09 Rev.
차례 모니터 정보 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 포장 내용물 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 제품의 특장점 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 부품과 조절 버튼 식별 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 앞면 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8 뒷면 . . . . . . . . . . . . . . . . . . . . . . .
컴퓨터 연결 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 모니터 스탠드 분리하기 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 벽걸이 ( 옵션 ). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 모니터 조작 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 모니터 전원 켜기. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 전면 패널 조절 사용하기 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 전면 패널 버튼 . . . .
모니터 정보 포장 내용물 모니터는 아래 그림에 표시된 구성 품목과 함께 제공됩니다 . 구성 품목을 받았 는지 확인한 다음 빠진 품목이 있을 경우 Dell 에 연락하십시오 . 참고 : 일부 항목은 옵션일 수 있으며 모니터와 함께 제공되지 않을 수 있습니 다 . 일부 기능 또는 매체는 특정 국가에서는 제공되지 않을 수 있습니다 . 참고 : 기타 스탠드를 설치하려면 , 스탠드 설치 안내서에 포함된 설치 지침을 참조하십시오 .
스탠드 베이스 마그네틱 덮개 케이블 덮개 전원 케이블 ( 국가별로 다름 ) HDMI 케이블 USB 3.
제품의 특장점 Alienware AW2518HF 평판 디스플레이에는 능동형 매트릭스 박막 트랜지스 터 (TFT) 액정 디스플레이 (LCD) 및 LED 백라이트가 탑재되어 있습니다 . 모니 터의 특장점에는 다음 사항이 포함됩니다 : • 62.23 cm (24.5 인치 ) 가시 영역 ( 대각선 측정 시 ). 해상도 : DisplayPort 및 HDMI 를 통해 최대 1920 x 1080, 전체 화면 지원 또는 더 낮은 해상도 . • 240 Hz 의 매우 높은 재생 빈도와 1 ms 의 빠른 응답 시간을 가진 AMD FreeSync 모니터 . • 색역 72% NTSC. • 기울이기 , 스위블 , 피벗 및 높이 조정 기능 . • 탈착식 스탠드와 VESA™ 100 mm 설치 구멍을 이용한 유연한 장착 가능 . • DisplayPort 및 HDMI 를 통한 디지털 연결성 . • 1 USB 업스트림 포트와 4 USB 다운스트림 포트를 가지고 있습니다 . • 사용자 시스템에 의해 지원될 경우 플러그 앤 플레이 기능 .
부품과 조절 버튼 식별 앞면 라벨 1 8 설명 케이블 관리 슬롯 ( 스탠드의 전면에 있음 ) 2 기능 버튼 ( 자세한 내용은 모니터 조작 참조 ) 3 전원 버튼 (LED 표시기 포함 ) | 모니터 정보
뒷면 모니터 스탠드가 장착된 상태의 뒷면 라벨 1 설명 사용 VESA 설치 구멍 (100 mm x VESA 호환형 벽면 설치 키트를 사용 100 mm - 뒤쪽에 부착된 VESA 하는 벽걸이형 모니터 (100 mm x 100 mm). 덮개 ) 2 규정에 의한 라벨 규정에 의한 승인을 표시합니다 . 3 스탠드 분리 버튼 스탠드를 모니터에서 분리합니다 . 4 바코드 일련번호 라벨 Dell 기술 지원 요청용 . 5 케이블 관리 슬롯 ( 스탠드의 왼쪽 및 오른쪽에 있음 ) 케이블을 슬롯을 통과하도록 설치하 여 배선하기 위한 슬롯입니다 .
후면 및 밑면 후면 및 밑면 모습 ( 모니터 스탠드 없음 ) 라벨 1 설명 전원 케이블 커넥터 전원 케이블 ( 모니터에 포함됨 ) 을 연결합 니다 . 2 (1, 2) 3 사용 HDMI 포트 HDMI 케이블 ( 모니터에 포함됨 ) 로 컴퓨터를 연결합니다 . 라인 출력 포트 스피커를 연결합니다 . 참고 : 이 포트는 헤드폰을 지원하지 않습니다 . 4 DisplayPort 5 USB 업스트림 포트 USB 케이블 ( 모니터와 함께 제공됨 ) 을 이 포 트와 컴퓨터에 연결하여 모니터의 USB 포트를 사용할 수 있게 합니다 . 6, 9 USB 3.0 포트 컴퓨터에 DP 케이블을 연결합니다 . USB 장치를 연결합니다 . 참고 : 이 포트를 사용하려면 USB 케이블 ( 모 니터와 함께 제공됨 ) 을 모니터의 USB 업스트 림 포트와 컴퓨터에 연결해야 합니다 . 7 전원 충전 기능이 있 연결하여 USB 장치를 충전합니다 .
모니터 규격 평판 규격 모델 AW2518HF 화면 유형 패널 기술 능동형 매트릭스 - TFT LCD TN 화면비 16:9 볼 수 있는 이미지 대각 622.3 mm (24.5 인치 ) 수평 , 활성 영역 543.74 mm (21.41 인치 ) 수직 , 활성 영역 302.62 mm (11.91 인치 ) 영역 픽셀 피치 164545.63 mm2 (255.05 인치 2) 0.2832 mm x 0.2802 mm 인치당 픽셀 (PPI) 90 시야각 160° ( 세로 ) 일반 170° ( 가로 ) 일반 휘도 출력 400 cd/m² ( 일반 ) 명암비 1000 대 1 ( 일반 ) 표면 코팅 눈부심 방지 , 3H 경도 백라이트 LED 에지라이트 시스템 응답 시간 1 ms 회색에서 회색으로 색심도 16.7 백만 컬러 72%* (CIE1931) 색역 내장 장치 • USB 3.0 초고속 허브 (1 x USB 3.0 업스트림 포트 포함 ) • 4 x USB 3.
• 1 x DP 1.2 연결성 • 2 x HDMI 2.0 • 1 x USB 3.0 업스트림 포트 ( 후면 ) • 2 x USB 3.0 다운스트림 포트 ( 후면 ) • 2 x USB 3.0 다운스트림 포트 ( 하단 ) • 1 x 헤드폰 출력 잭 ( 하단 ) • 1 x 오디오 라인 출력 잭 ( 후면 ) 테두리 너비 ( 모니터 가장자리 6.02 mm( 상단 / 왼쪽 / 오른쪽 ) 에서 활성 영역까지 ) 19.23 mm( 하단 ) 조정 가능성 높이 조정 가능한 스탠드 0 ~ 130 mm 기울이기 -5° ~ 25° 좌우회전 피벗 Dell Display Manager (DDM) 호환성 -20° ~ 20° -90° ~ 90° 예 * 색역 ( 일반 ) 은 CIE1976 (82%) 과 CIE1931 (72%) 시험 표준에 기초해 있습 니다 . 해상도 규격 모델 AW2518HF 수평 주사 범위 249.
사전 설정 디스플레이 모드 HDMI 디스플레이 모드 디스플레이 모드 수평 주파수 수직 주파수 (kHz) (Hz) 픽셀 클록 (MHz) 동기 극성 ( 수평 / 수직 ) VESA, VGA, 640 x 480 31.5 60 25.2 -/- VESA, 800 x 600 37.88 60 40 +/+ VESA, 1024 x 768 48.36 60 65 -/- HDTV, 1920 x 1080p 67.5 60 148.5 +/+ HDTV, 1920 x 1080p @ 120 Hz 137.26 120 285.5 +/- HDTV, 1920 x 1080p @ 144 Hz 166.59 144 346.5 +/- HDTV, 1920 x 1080p @ 240 Hz 291.31 240 594.
전기 규격 모델 AW2518HF 비디오 입력 신호 • HDMI 2.0, 각 라인당 600 mV, 각 쌍당 100 오옴의 입력 임피던스 • DisplayPort 1.2, 각 라인당 600 mV, 각 쌍당 100 오 옴의 입력 임피던스 동기화 입력 신호 수평 및 수직 동기화 분리 , 무극성 TTL 레벨 , 복합 싱 크 - 온 - 그린 (Composite SYNC on green: SOG) AC 입력 전압 / 주파수 / 전류 100 VAC ~ 240 VAC / 50 Hz 또는 60 Hz + 3 Hz / 1.
깊이 268.6 mm (10.57 인치 ) 중량 중량 ( 포장 포함 ) 11.13 kg (24.52 lb) 스탠드 어셈블리와 케이블을 포함한 중량 6.88 kg (15.15 lb) 스탠드 어셈블리 미포함 중량 3.38 kg (7.45 lb) ( 벽 설치 또는 VESA 설치를 위한 고려사항의 경우 - 케이 블 없음 ) 3.20 kg (7.
전원 관리 모드 PC 에 VESA 의 DPM ™ 준수 디스플레이 카드나 소프트웨어가 설치되어 있는 경우 모니터를 사용하지 않는 동안 모니터가 자동으로 소비 전력을 줄입니다 . 이것을 절전 모드 * 라고 합니다 . 컴퓨터가 키보드 , 마우스 또는 기타 입력 장치 에 의한 입력을 감지할 경우 모니터는 자동으로 절전 모드에서 해제되어 작동합 니다 . 다음 표는 이 자동 절전 기능의 소비 전력 및 신호를 나타냅니다 . VESA 모드 수평 동기 수직 동기 정상 작동 활성 활성 비디오 활성 전원 표시등 파란색 소비 전력 65 W ( 최대 )** 17.6 W ( 일반 ) 활성 - 꺼짐 비활성 모드 스위치 꺼짐 - 비활성 - 귀선 소거 주황색 ( 깜 0.3 W 미만 박임 ) 꺼짐 0.3 W 미만 소비 전력 Pon 13.5 W 총 에너지 소비 (TEC) 43.1 kWh * 모니터에서 주전원 케이블을 뽑아야만 꺼짐 모드에서 소비 전력이 0 이 될 수 있습니다 .
OSD 는 정상 동작 모드에서만 동작합니다 . 활성 - 꺼짐 모드에서 아무 버튼이나 누르면 다음 메시지가 표시됩니다 : 참고 : 연결된 입력 신호에 따라 메시지가 약간 다를 수 있습니다 .
핀 지정 DisplayPort 커넥터 핀 번호 18 | 연결된 신호 케이블의 20 핀 면 1 ML3 (n) 2 GND 3 ML3 (p) 4 ML2 (n) 5 GND 6 ML2 (p) 7 ML1 (n) 8 GND 9 ML1 (p) 10 ML0 (n) 11 GND 12 ML0 (p) 13 GND 14 GND 15 AUX (p) 16 GND 17 AUX (n) 18 핫 플러그 감지 19 Re-PWR 20 +3.
HDMI 커넥터 핀 번호 연결된 신호 케이블의 19 핀 면 1 TMDS 데이터 2+ 2 TMDS 데이터 2 쉴드 3 TMDS 데이터 2- 4 TMDS 데이터 1+ 5 TMDS 데이터 1 쉴드 6 TMDS 데이터 1- 7 TMDS 데이터 0+ 8 TMDS 데이터 0 쉴드 9 TMDS 데이터 0- 10 TMDS 클록 + 11 TMDS 클록 쉴드 12 TMDS 클록 - 13 CEC 14 예약됨 ( 장치의 N.C.
플러그 앤 플레이 기능 이 모니터는 어떠한 플러그 앤 플레이 호환 시스템에든 설치할 수 있습니다 . 모 니터는 디스플레이 데이터 채널 (DDC) 프로토콜을 사용하여 컴퓨터 시스템에 확장 디스플레이 식별 데이터 (EDID) 를 제공함으로써 시스템이 자체적으로 구 성하고 모니터 설정을 최적화도록 합니다 . 대다수 모니터 설치는 자동으로 실행 되므로 원할 경우 다른 설정을 선택할 수 있습니다 . 모니터 설정 변경에 대한 자 세한 내용은 모니터 조작를 참조하십시오 . 범용 직렬 버스 (USB) 인터페이스 이 단원에서는 모니터에 탑재된 USB 포트에 대한 정보를 제공합니다 . 참고 : 이 모니터는 초고속 USB 3.0 호환입니다 . 전송 속도 소비 전력 * 데이터 전송 속도 초고속 5 Gbps 4.5 W ( 최대 , 각 포트 ) 고속 480 Mbps 4.5 W ( 최대 , 각 포트 ) 완속 12 Mbps 4.5 W ( 최대 , 각 포트 ) * BC1.
8 SSRX- 9 SSRX+ USB 다운스트림 커넥터 핀 번호 커넥터의 9 핀 쪽 1 VCC 2 D- 3 D+ 4 GND 5 SSRX- 6 SSRX+ 7 GND 8 SSTX- 9 SSTX+ USB 포트 • 업스트림 1 개 - 후면 • 다운스트림 2 개 - 후면 • 다운스트림 2 개 - 하단 • 충전 포트 배터리 아이콘이 있는 포트 ; BC1.2 호환 장치인 경우 신 속 충전 기능을 지원합니다 . 참고 : USB 3.0 기능을 사용하려면 USB 3.0 을 지원하는 컴퓨터가 있어야 합 니다 . 참고 : 모니터의 USB 인터페이스는 모니터가 켜져 있을 때 또는 절전 모드에 있을 때에만 동작합니다 . 모니터를 껐다 켜면 연결된 주변장치가 정상 기능 을 재작동시키는 데 몇 초가 걸릴 수 있습니다 .
LCD 모니터 화질 및 픽셀 지침 LCD 모니터 제조 공정 중에 한 개 이상의 픽셀이 불변 상태로 고정되어 제대로 보이지 않는 경우가 있습니다 . 이것은 일반적인 현상이며 디스플레이의 화질 또 는 사용성에 영향을 주지 않습니다 . Dell 모니터 품질 및 픽셀 정책에 대해서는 Dell 지원 사이트를 참조하십시오 : http://www.dell.com/support/monitors. 유지보수 지침 모니터 청소 주의 : 모니터를 청소하기 전에 안전 지침을 읽고 따르십시오 . 경고 : 모니터를 청소하기 전에 모니터의 전원 케이블을 전기 콘센트에서 뽑 으십시오 . 모범적으로 관리하려면 모니터를 포장을 풀거나 청소하거나 취급할 때 아래 목 록의 지침을 따르십시오 . • 대전방지 화면을 청소하기 전에 부드럽고 깨끗한 헝겊에 물을 약간 축이십 시오 . 가능하면 대전방지 코팅에 적합한 특수 화면 청소용 티슈나 용액을 사용하십시오 . 벤젠 , 희석제 , 암모니아수 , 연마 세제 또는 압축 공기를 사 용하지 마십시오 .
모니터 설치 스탠드 부착하기 참고 : 스탠드는 모니터에서 분리되어 출고됩니다 . 참고 : 이것은 스탠드 장착형 모니터에 적용될 수 있습니다 . 스탠드 설치 안 내서에 포함된 설치 지침을 참조하십시오 . 모니터 스탠드 부착하기 : 1. 모니터를 부드러운 천이나 쿠션 위에 놓습니다 . 2. 스탠드 받침에 스탠드 라이저를 맞추고 제자리에 넣습니다 .
3. 나사 핸들을 열고 , 나사를 시계 방향으로 돌려 스탠드 라이저를 스탠드 받 침에 고정시킵니다 . 4. 나사를 조인 후 , 나사 핸들을 닫습니다 . 5. 마그네틱 나사 덮개를 스탠드 받침에 맞추고 제자리에 넣습니다 . 6. 제자리에 들어갈 때까지 스탠드 어셈블리에 있는 탭을 모니터의 슬롯에 밀 어 넣습니다 .
7. 그림에 나온 것처럼 필요한 케이블을 배선하여 모니터에 연결합니다 . a. 전원 케이블 b. HDMI 케이블 c. DP 케이블 ( 선택 사항 , 케이블 미포함 ) d. USB 업스트림 케이블 e. USB 다운스트림 케이블 ( 선택 사항 , 케이블 미포함 ) 참고 : 케이블 덮개를 부착한 후 케이블들이 잘 정리되도록 각 케이블을 깔끔 하게 배선합니다 . 경고 : 지시가 있을 때까지 모니터의 전원을 켜거나 플러그를 꽂지 마십시오 . 8. 케이블 덮개에 있는 탭이 모니터 뒷면에 있는 슬롯 1 및 슬롯 2 와 정렬되어 있어야 합니다 . 9. 케이블 덮개에 있는 탭이 모니터 뒷면에 있는 슬롯 3 및 슬롯 4 와 정렬되어 있어야 합니다 .
10. 아래 그림과 같이 양손 엄지와 손가락을 사용하여 딸깍 소리가 나면서 제 위치에 고정될 때까지 케이블 덮개를 밉니다 . 참고 : 케이블이 케이블 덮개의 바닥을 통과할 수 있도록 합니다 . 컴퓨터 연결 경고 : 이 단원에 있는 절차를 시작하기 전에 안전 지침을 따르십시오 . 참고 : 모든 케이블을 컴퓨터에 동시에 연결하지 마십시오 . 참고 : 스탠드 부착하기를 참조하십시오 . 모니터를 컴퓨터에 연결하기 : 1. 연결된 DP 또는 HDMI 케이블의 다른 쪽 끝을 컴퓨터에 연결합니다 . 2. USB 3.0 업스트림 포트 ( 케이블 제공됨 ) 를 컴퓨터의 적절한 USB 3.0 포 트에 연결합니다 . ( 자세한 내용은 후면 및 밑면참조 .) 3. USB 3.0 주변장치를 모니터의 USB 3.0 다운스트림 포트에 연결합니다 . 4. 컴퓨터와 모니터의 전원 케이블을 근처의 콘센트에 꽂습니다 .
5. 모니터와 컴퓨터를 켭니다 . 모니터에 이미지가 나타나면 설치가 완료된 것입니다 . 이미지가 나타나지 않을 경우 범용 직렬 버스 (USB) 관련 문제를 참조하십시오 . 참고 : 그림은 참조용으로만 사용됩니다 . 컴퓨터의 외관은 다를 수 있습 니다 . 모니터 스탠드 분리하기 참고 : 스탠드를 분리하는 중에 LCD 화면의 긁힘을 방지하기 위해 모니터를 깨끗한 면에 놓습니다 . 참고 : 이것은 스탠드 장착형 모니터에 적용될 수 있습니다 . 스탠드 설치 안 내서에 포함된 설치 지침을 참조하십시오 . 스탠드 분리하기 : 1. 모니터를 끕니다 . 2. 컴퓨터에서 케이블을 뽑습니다 . 3. 모니터를 부드러운 천이나 쿠션 위에 놓습니다 . 4. 케이블 덮개를 부드럽게 누르고 밀어서 모니터에서 떼어 냅니다 .
5. 모니터에서 케이블을 뽑습니다 . 6. 스탠드 분리 버튼을 누른 채로 있습니다 . 7. 스탠드를 위로 들어 올려 모니터에서 분리합니다 .
벽걸이 ( 옵션 ) ( 나사 치수 : M4 x 10 mm). VESA 호환형 벽면 장착 키트와 함께 제공되는 지침을 참조하십시오 . 1. 안정된 평평한 탁자에 부드러운 천 또는 쿠션을 깔고 모니터 패널을 그 위 에 올려 놓습니다 . 2. 스탠드를 제거합니다 . 3. Phillips 십자 스크루드라이버를 사용하여 플라스틱 커버를 고정하는 네 개 의 나사를 제거합니다 . 4. 벽걸이 키트의 장착 브래킷을 모니터에 부착합니다 . 5. 벽면 장착 키트와 함께 제공되는 지침을 따라 모니터를 벽에 장착합니다 . 참고 : 최소 중량 / 하중 지지 용량이 13.52 kg 인 UL 인증 벽걸이 브래킷하 고만 사용할 수 있습니다 .
모니터 조작 모니터 전원 켜기 모니터를 켜려면 전원 버튼을 누릅니다 . 전면 패널 조절 사용하기 모니터 전면의 제어 버튼을 사용하여 설정을 조정합니다 . 다음 표에서는 전면 패널 버튼에 대해 설명합니다 : 전면 패널 버튼 1 바로 가기 키 / Preset Modes( 사전 설정 모드 ) 2 바로 가기 키 / Game Enhance Mode( 게임 향상 모드 ) 30 | 모니터 조작 설명 이 단축 키를 선택하면 사전 설정 컬러 모드의 목록 중에서 선 택할 수 있습니다 . Game Enhance Mode(게임 향상 모드) 메뉴를 실행하려면 이 버튼을 사용합니다 .
3 바로 가기 키 / Dark Stabilizer ( 어두움 안정화 ) 4 바로 가기 키 / Brightness/ Contrast( 밝기 / 명암 대비 ) 5 메뉴 6 Dark Stabilizer( 어두움 안정화 ) 메뉴를 실행하려면 이 버튼 을 사용합니다 . 이 버튼은 Brightness/Contrast( 밝기 / 명암 대비 ) 메뉴에 직접 액세스하는 데 사용됩니다 . 메뉴 버튼을 사용하여 OSD( 온스크린 디스플레이 ) 를 실행 합니다 . 메뉴 시스템 액세스하기을 참조하십시오 . 이 버튼을 사용하여 OSD 메인 메뉴를 종료합니다 . 종료 전면 패널 버튼 모니터 전면 버튼을 사용하여 이미지 설정을 조정합니다 . 전면 패널 버튼 1 위로 2 아래로 3 설명 위로 버튼을 사용하여 OSD 메뉴의 항목을 조정합니다 ( 범위 증가 ). 아래로 버튼을 사용하여 OSD 메뉴의 항목을 조정합니다 ( 범 위 감소 ). 선택 버튼을 사용하여 선택 내용을 확인합니다 .
OSD 메뉴 사용하기 메뉴 시스템 액세스하기 참고 : 설정을 변경하고 다른 메뉴로 가거나 OSD 메뉴를 종료하면 모니터가 자동으로 이 변경 내용을 저장합니다 . 설정을 변경한 다음 OSD 메뉴가 사라 지길 기다리는 동안에도 변경 내용이 저장됩니다 . 1. 2. 버튼을 눌러 OSD 메뉴를 실행하여 주 메뉴를 표시합니다 . 및 버튼을 눌러 설정 옵션 사이에서 이동합니다 . 한 아이콘에서 다 른 아이콘으로 이동할 때 옵션 이름이 강조 표시됩니다 . 모니터에서 사용 할 수 있는 모든 옵션의 전체 목록은 아래 표를 참조하십시오 . 3. 버튼을 한 번 눌러 강조 표시된 옵션을 활성화합니다 . 4. 및 5. 버튼을 눌러 원하는 파라미터를 선택합니다 . 를 눌러 하위 메뉴로 들어간 다음 방향 버튼을 사용하여 메뉴에 있는 표 시기를 따라 변경합니다 . 6. 32 | 버튼을 선택하여 주 메뉴로 돌아갑니다 .
아이콘 메뉴 및 하위 메뉴 설명 Game( 게임 ) 시각적 게임플레이 경험을 개인 맞춤화하려면 이 메뉴를 사용 합니다 . Preset Modes 사전 설정 컬러 모드의 목록에서 모드를 선택할 수 있습니다 . ( 사전 설정 모드 ) • Standard( 표준 ): 모니터의 기본 색상 설정을 로드합니다 . 이것은 기본 사전 설정 모드입니다 . • FPS: 일인칭 슈팅 게임에 적합한 색상 설정을 로드합니다 . • RTS: 실시간 전략 게임에 적합한 색상 설정을 로드합니다 . • RPG: 롤 플레잉 게임에 적합한 색상 설정을 로드합니다 . • Game 1( 게임 1)/Game 2( 게임 2)/Game 3( 게임 3): 자신의 게임 필요에 맞게 색 설정을 사용자 지정할 수 있습 니다 .
Preset Modes • ComfortView: 눈에 좀더 보기 편안하도록 화면에서 나오 ( 사전 설정 는 청광 수준을 줄입니다 . 모드 ) 경고 : 모니터에서 방출하는 블루 라이트에 장시간 노출되면 디지털 눈 경련 , 눈 피로 및 눈 상해와 같은 해를 입을 수 있습니다 . 모니터를 장시간 사용할 경 우 목 , 팔 , 등 및 어깨와 같은 신체 부위에 통증을 일 으킬 수도 있습니다 . 모니터를 장시간 사용할 때 눈 경련 및 목 / 팔 / 등 / 어깨 고통을 줄이기 위해 , 다음 제안을 따르는 것이 좋습니다 . 1. 눈과 화면 간에 20 인치 -28 인치 (50cm-70cm) 거리를 유지하도록 설정하십시오 . 2. 눈을 자주 깜박여 촉촉게 유지하고 모니터를 오래 사용 한 후에는 물로 눈을 적시십시오 . 3. 정기적으로 두 시간마다 20 분 동안 휴식합니다 . 4. 쉬는 동안 최소 20 초 동안 모니터에서 눈을 떼고 20 피 트 떨어진 곳의 사물을 응시합니다 . 5.
Game Enhance 이 기능은 게임플레이 경험을 향상시키기 위한 세 가지 기능 Mode( 게임 향 을 제공합니다 . 상 모드 ) • Off( 꺼짐 ) Game Enhance Mode( 게임 향상 모드 ) 하에서 기능을 비활 성화하기 위해 선택합니다 . • Timer( 타이머 ) 디스플레이의 왼쪽 위 구석에 있는 타이머를 활성화 또는 비 활성화할 수 있습니다 . 게임이 시작된 후로 경과된 시간을 표 시합니다 . 목표 게임 속도를 측정하기 위해 시간 간격 목록에 서 옵션을 선택합니다 . • Frame Rate( 프레임 속도 ) On( 켜기 ) 을 선택하면 게임을 플레이할 때 현재의 초당 프레 임 수를 표시합니다 . 속도가 높을수록 동작이 더 부드럽게 나 타납니다 . • Display Alignment( 디스플레이 정렬 ) 여러 디스플레이의 비디오 콘텐츠를 완벽하게 정렬하는 데 도 움이 되는 기능을 활성화합니다 .
Dark 이 기능은 어두운 게이밍 시나리오에서 가시성을 높여줍니 Stabilizer( 어두 다 . 값이 높으면 (0 ~ 3 사이 ), 디스플레이 이미지의 어두운 움 안정화 ) 영역에서 가시성이 더 좋아집니다 . Hue( 색조 ) 이 기능은 비디오 이미지의 색상을 녹색 또는 자주색으로 변 화시킵니다 . 이것은 원하는 살색을 조정하는 데 사용됩니다 . 또는 합니다 . 을 사용하여 색조 수준을 0 ~ 100 사이에서 조정 를 사용하면 비디오 이미지의 녹색 음영이 높아집니다 . 를 사용하면 비디오 이미지의 자주색 음영이 높아집니다 . 참고 : Hue( 색조 ) 조정은 FPS, RTS 또는 RPG 사전 설정 모드 를 선택한 경우에만 사용 가능합니다 . Saturation ( 채도 ) 이 기능은 비디오 이미지의 채도를 조정할 수 있습니다 . 또는 합니다 . 을 사용하여 채도 수준을 0 ~ 100 사이에서 조정 을 사용해 비디오 이미지의 색채 현시를 높입니다 .
Brightness/ Contrast ( 밝기 / 명암 대비 ) Brightness ( 밝기 ) Contrast ( 명암 대비 ) 이 메뉴를 사용하여 Brightness/Contrast( 밝기 / 명암 대비 ) 조정을 활성화합니다 . Brightness( 밝기 ) 는 백라이트의 휘도를 조정합니다 . 버튼을 누르면 밝기가 증가하고 감소합니다 ( 최소 0 / 최대 100). 버튼을 누르면 밝기가 Brightness( 밝기 ) 를 먼저 조정한 후 추가 조정이 필요한 경 우에만 Contrast( 명암 대비 ) 를 조정합니다 . 버튼을 누르면 명암 대비가 증가하고 버튼을 누르면 명암 대비가 감소합니다 ( 최소 0 / 최대 100). Contrast( 명암 대비 ) 기능은 모니터 화면의 밝고 어두운 정도 의 차이를 조정합니다 .
Input Source ( 입력 소스 ) DP HDMI 1 HDMI 2 Input Source( 입력 소스 ) 메뉴를 사용하여 모니터에 연결할 수 있는 서로 다른 비디오 신호 중에서 선택합니다 . DP 커넥터를 사용하고 있을 때 DP 입력을 선택합니다 . HDMI 커넥터를 사용하고 있을 때 HDMI 1 또는 HDMI 2 입력 을 선택합니다 . Auto Select ( 자동 선택 ) 기능을 켜면 사용 가능한 입력 소스를 스캔할 수 있습니다 . Reset Input Source( 입력 소스 재설정 ) 모니터 입력 설정을 공장 설정으로 초기화합니다 . Display Display( 디스플레이 ) 를 사용하여 이미지를 조정합니다 . ( 디스플레이 ) Aspect Ratio ( 화면비 ) 38 | 모니터 조작 이미지 비율을 Wide 16:9( 와이드 16:9), Auto Resize( 자동 크기 조정 ), 4:3 또는 1:1 로 조정합니다 .
Input Color 비디오 입력 모드를 설정할 수 있습니다 : Format( 입력 색 RGB: 모니터가 DP 또는 HDMI 케이블을 사용하여 컴퓨터 상 형식 ) ( 또는 DVD 플레이어 ) 에 연결된 경우 이 옵션을 선택하십 시오 . YPbPr: DVD 플레이어가 YPbPr 출력만 지원하는 경우 이 옵 션을 선택합니다 . Sharpness ( 선명도 ) 이 기능은 이미지를 더 선명하게 또는 더 부드럽게 보이게 합 니다 . 또는 서 조정합니다 . 을 사용하여 선명도 수준을 0 ~ 100 사이에 Dynamic 대비 수준을 증가시켜 더 선명하고 상세한 이미지 품질을 만 Contrast( 동적 들 수 있도록 합니다 . 명암 대비 ) 버튼을 눌러 Dynamic Contrast( 동적 명암 대비 ) "On"( 켜짐 ) 또는 "Off"( 꺼짐 ) 을 선택합니다 .
Menu( 메뉴 ) 이 옵션을 선택하여 OSD 언어 , 메뉴가 화면에 머무르는 시간 의 길이 등과 같은 OSD 설정을 조정합니다 . Language ( 언어 ) OSD 디스플레이를 8 개 언어 ( 영어 , 스페인어 , 프랑스어 , 독 일어 , 브라질 포르투갈어 , 러시아어 , 중국어 간체 또는 일본 어 ) 가운데 하나로 설정할 수 있습니다 . Transparency ( 투명도 ) 이 옵션을 선택하면 및 버튼을 눌러 메뉴 투명도를 변 경할 수 있 습니다 ( 최소 0 / 최대 100). Timer( 타이머 ) 사용자가 마지막으로 버튼을 누른 뒤 OSD 가 활성 상태에 머 물러 있는 시간의 길이를 설정합니다 . 또는 버튼을 사용하여 5 초에서 60 초까지 1 초 단위 로 슬라이더를 조정합니다 . Reset Menu 모든 OSD 설정을 공장 사전 설정값으로 초기화합니다 .
Personalize ( 개인 설정 ) Shortcut Key 1 Preset Modes( 사전 설정 모드 ), Game Enhance Mode( 게임 ( 바로 가기 키 1) 향상 모드 ), Dark Stabilizer( 어두움 안정화 ), Brightness/ Shortcut Key 2 Contrast( 밝기 / 명암 대비 ), Input Source( 입력 소스 ), Aspect Ratio( 화면비 ) 또는 Volume( 볼륨 ) 기능 중에서 선 ( 바로 가기 키 2) 택하여 이를 바로 가기 키로 설정할 수 있습니다 . Shortcut Key 3 ( 바로 가기 키 3) Shortcut Key 4 ( 바로 가기 키 4) Power Button 에너지 절약을 위해 전원 LED 표시등을 켜거나 끌 수 있습 LED( 전원 버튼 니다 . LED) USB 모니터 대기 모드 동안 USB 기능을 활성화 또는 비활성화할 수 있습니다 .
Others( 기타 ) Display Info ( 디스플레이 정보 ) DDC/CI 모니터의 현재 설정을 표시합니다 . DDC/CI( 디스플레이 데이터 채널 / 명령 인터페이스 ) 는 컴퓨터에 설치된 소프트웨어를 사용하여 모니터 파라미터 ( 밝기 , 색상 , 밸런스 등 ) 를 조정할 수 있게 합니다 . Off( 꺼짐 ) 을 선택하여 이 기능을 사용 안 할 수 있습니다 . 이 기능을 사용 설정하면 모니터에 대한 최상의 사용자 경험 과 최적 성능을 얻을 수 있습니다 .
LCD Conditioning (LCD 조절 ) 이 기능은 사소한 잔상을 줄입니다 . 잔상의 정도에 따라 프로 그램이 실행되는 데 약간의 시간이 걸릴 수 있습니다 . On ( 켜짐 ) 을 선택하여 이 기능을 활성화할 수 있습니다 . Reset Others Others( 기타 ) 메뉴 아래의 모든 설정을 공장 사전 설정값으 ( 기타 재설정 ) 로 초기화합니다 . Factory Reset 모든 설정을 공장 사전 설정값으로 초기화합니다 . ( 공장 초기화 ) OSD 경고 메시지 Dynamic Contrast( 동적 명암 대비 ) 기능이 활성화되어 있을 때 ( 사전 설정 모 드 : FPS, RTS, RPG, Game 1( 게임 1), Game 2( 게임 2), Game 3( 게임 3)), 수동 밝기 조정은 비활성화됩니다 .
모니터가 특정 해상도를 지원하지 않으면 다음 메시지가 표시됩니다 : 참고 : 연결된 입력 신호에 따라 메시지가 약간 다를 수 있습니다 . 이것은 모니터가 컴퓨터에서 수신 중인 신호와 동기화할 수 없음을 뜻합니다 . 이 모니터가 처리할 수 있는 수평 및 수직 주파수 범위에 대해서는 모니터 규격 을 참조하십시오 . 권장 모드는 1920 x 1080 입니다 . DDC/CI 기능이 사용 해제되기 전에 다음 메시지가 표시됩니다 : 모니터가 절전 모드에 들어가면 다음 메시지가 표시됩니다 : OSD 메뉴 사용하기를 이용하려면 컴퓨터를 켜서 모니터를 절전 모드에서 해제 하십시오 . 참고 : 연결된 입력 신호에 따라 메시지가 약간 다를 수 있습니다 .
전원 버튼 이외의 아무 버튼이나 누르면 선택된 입력에 따라 다음 메시지가 표시 됩니다 : 참고 : 연결된 입력 신호에 따라 메시지가 약간 다를 수 있습니다 . HDMI 또는 DP 입력 중에서 하나를 선택했고 해당 케이블을 연결하지 않았다면 아래와 같이 이동하는 대화 상자가 나타납니다 . 참고 : 연결된 입력 신호에 따라 메시지가 약간 다를 수 있습니다 . 자세한 내용은 문제 해결을 참조하십시오 . 최적 해상도 설정하기 모니터 최대 해상도 설정하기 : Windows® 7, Windows® 8 및 Windows® 8.1 에서 : 1. Windows® 8 및 Windows® 8.1 에서는 데스크톱 타일을 선택하여 고전적인 데스크톱으로 전환합니다 . 2. 바탕 화면을 오른쪽 클릭한 다음 화면 해상도를 선택합니다 . 3. 화면 해상도의 드롭다운 목록을 클릭하고 1920 x 1080 을 선택합니다 . 4. 확인을 클릭합니다 . Windows® 10 에서 : 1.
4. 적용을 클릭합니다 . 1920 x 1080 옵션이 없는 경우 그래픽 드라이버를 업데이트할 필요가 있을 수 있습니다 . 사용자의 컴퓨터에 따라서 다음 절차 중의 하나를 완료하십시오 : Dell 데스크톱 또는 휴대용 컴퓨터의 경우 : • http://www.dell.com/support 으로 이동하여 사용자의 서비스 태그를 입력한 다음 사용자의 그래픽카드에 대한 최근 드라이버를 다운로드합 니다 . Dell 컴퓨터 ( 휴대용 또는 데스크톱 ) 가 아닌 다른 컴퓨터를 사용하는 경우 : • 컴퓨터의 지원 사이트를 방문하여 최신 그래픽 드라이버를 다운로드하십 시오 . • 그래픽 카드 웹사이트를 방문하여 최신 그래픽 드라이버를 다운로드하십 시오 . 기울이기 , 좌우 회전 , 수직 확장 사용하기 참고 : 이것은 스탠드 장착형 모니터에 적용될 수 있습니다 . 기타 스탠드를 구입할 때 , 스탠드 설치 안내서에 포함된 설치 지침을 참조하십시오 .
수직 확장 참고 : 스탠드 높이를 최대 130 mm 높일 수 있습니다 . 아래 그림들은 스탠드 높이를 높이는 방법을 보여줍니다 . 모니터 회전시키기 모니터를 회전시키기 전에 모니터를 완전히 수직으로 확장 ( 수직 확장 ) 시키거 나 완전히 기울여야만 모니터의 하단 가장자리가 부딪치는 것을 피할 수 있습 니다 .
시계 방향으로 회전 반시계 방향으로 회전 참고 : Dell 컴퓨터에서 디스플레이 회전 기능을 사용하려면 ( 가로 보기 대 세로 보기 ) 이 모니터에 포함되지 않은 업데이트된 그래픽 드라이버를 설치해야 합니다 . 이 그래픽 드라이버를 다운로드하려면 www.dell.com/support 에 접속하여 비디오 드라이버의 다운로드 섹션에서 최신 드라이버 업데이트를 확인하십시오 .
참고 : 세로 보기 모드에 있을 경우 그래픽 중심형 응용 프로그램들 (3D 게임 등 ) 의 성능 저하가 발생할 수 있습니다 . 시스템의 회전 디스플레이 설정 조정하기 모니터를 회전시킨 다음 아래의 절차를 완료하여 시스템의 회전 디스플레이 설 정을 조정해야 합니다 . 참고 : 모니터를 Dell 제품이 아닌 컴퓨터와 사용하는 경우 그래픽 드라이버 웹사이트또는 컴퓨터 제조업체 웹사이트를 방문하여 운영 체제 회전에 관한 정보를 얻어야 합니다 . 회전 디스플레이 설정 조정하기 : 1. 바탕 화면을 오른쪽 클릭한 다음 속성을 클릭합니다 . 2. 설정 탭을 선택한 후 고급을 클릭합니다 . 3. ATI 그래픽 카드를 사용하는 경우 회전 탭을 선택한 다음 원하는 회전각을 설정합니다 . 4. nVidia 그래픽 카드를 사용하는 경우 nVidia 탭을 클릭하고 , 왼쪽 열에서 NVRotate 를 선택한 다음 원하는 회전각을 선택합니다 . 5.
문제 해결 경고 : 이 단원에 있는 절차를 시작하기 전에 안전 지침을 따르십시오 . 자가 검사 사용자는 이 모니터의 자가 시험 기능을 이용하여 모니터가 제대로 동작하는지 점검할 수 있습니다 . 모니터와 컴퓨터가 제대로 연결되어 있는데도 모니터 화면 이 켜지지 않으면 다음 단계를 수행하여 모니터 자가 검사를 실행합니다 : 1. 컴퓨터와 모니터를 모두 끕니다 . 2. 컴퓨터의 후면에서 비디오 케이블을 뽑습니다 . 3. 모니터를 켭니다 . 모니터가 정상적으로 동작하면서도 비디오 신호를 감지할 수 없는 경우 움직이 는 대화 상자가 화면 ( 흑색 배경 ) 에 표시됩니다 . 자가 검사 모드에서는 전원 LED 가 파란색으로 켜져 있습니다 . 또한 , 선택한 입력에 따라 아래의 대화상자 가 화면을 계속 스크롤합니다 . 참고 : 연결된 입력 신호에 따라 메시지가 약간 다를 수 있습니다 . 4. 비디오 케이블의 연결이 해제되거나 손상된 경우 정상적인 시스템 작동 중 에도 이 상자가 나타납니다 . 5.
내장형 진단 도구 모니터에 내장된 진단 도구는 화면 비정상이 모니터의 고유한 문제인지 아니면 컴퓨터와 비디오 카드의 문제인지 판단하는 데 도움을 줍니다 . 참고 : 비디오 케이블이 뽑혀 있고 모니터가 자가 검사 모드에 있을 때만 내장 된 진단 도구를 실행할 수 있습니다 . 내장된 진단 도구 실행하기 : 1. 화면이 깨끗한지 확인합니다 ( 화면 표면에 먼지 입자가 없는지 확인 ). 2. 컴퓨터 또는 모니터의 후면에서 비디오 케이블을 뽑습니다 . 그러면 모니터 가 자가 검사 모드에 들어갑니다 . 3. 버튼 3 을 5 초 동안 누릅니다 . 회색 화면이 표시됩니다 . 4. 화면의 비정상 여부를 주의하여 검사합니다 . 5. 버튼 3 을 다시 누릅니다 . 화면 색상이 적색으로 변합니다 . 6. 디스플레이의 비정상 여부를 검사합니다 . 7. 녹색 , 청색 , 검정 , 백색 화면에서 5 단계와 6 단계를 반복하여 디스플레이 를 검사합니다 . 흰색 화면이 표시되면 검사가 완료됩니다 .
일반적 문제 다음 표에는 일반적인 모니터 문제에 관한 일반 정보와 사용 가능한 해결책이 나 와 있습니다 : 일반 증상 문제 가능한 해결책 비디오 없음 / 전 영상 없음 원 LED 꺼짐 • 모니터와 컴퓨터를 연결하는 비디오 케이블이 올 바르게 단단히 연결되어 있는지 확인합니다 . • 다른 전기 장비를 사용하여 전원 콘세트가 올바 르게 작동하고 있는지 확인합니다 . • 전원 버튼을 완전히 눌렀는지 확인합니다 . • Input Source ( 입력 소스 ) 메뉴에서 올바른 입력 소스가 선택되었는지 확인하십시오 . 비디오 없음 / 전 영상이 없거나 원 LED 켜짐짐 어두움 • OSD 를 사용하여 밝기와 명암 대비를 증가시킵 니다 . • 모니터 자가 검사 기능 점검을 수행합니다 . • 비디오 케이블 커넥터의 핀이 구부러지거나 부러 졌는지 확인합니다 . • 내장된 진단 도구를 실행합니다 . • Input Source ( 입력 소스 ) 메뉴에서 올바른 입력 소스가 선택되었는지 확인하십시오 .
고정된 픽셀 LCD 화면에 밝 은 점이 있음 • 전원을 껐다가 다시 켭니다 . • 영구적으로 꺼져 있는 픽셀은 LCD 기술에서 발 생할 수 있는 자연적인 결함입니다 . • Dell 모니터 품질 및 픽셀 정책에 대해서는 Dell 지원 사이트를 참조하십시오 : http://www.dell.com/support/monitors. 밝기 문제 영상이 너무 어 둡거나 너무 밝음 • 모니터를 공장 설정으로 초기화합니다 . • OSD 를 사용하여 밝기와 명암 대비를 조정합 니다 . 기하학적인 왜곡 화면이 정확하게 • 모니터를 공장 설정으로 초기화합니다 . 가운데 놓이지 않음 가로 / 세로 줄 화면에 하나 이 상의 줄이 있음 • 모니터를 공장 설정으로 초기화합니다 . • 모니터 자가 검사 기능 점검을 수행하고 자가 검사 모드에서도 이 선들이 나타나는지 확인합 니다 . • 비디오 케이블 커넥터의 핀이 구부러지거나 부러 졌는지 확인합니다 . • 내장된 진단 도구를 실행합니다 .
색 손실 영상 색 손실 • 모니터 자가 검사 기능 점검을 수행합니다 . • 모니터와 컴퓨터를 연결하는 비디오 케이블이 올 바르게 단단히 연결되어 있는지 확인합니다 . • 비디오 케이블 커넥터의 핀이 구부러지거나 부러 졌는지 확인합니다 . 색상 오류 영상 색상 불량 • 응용 프로그램에 따라 Game( 게임 ) 메뉴 OSD 에서 Preset Modes( 사전 설정 모드 ) 의 설정을 변경합니다 . • Game( 게임 ) 메뉴 OSD 의 Custom Color( 사용 자 지정 색상 ) 아래서 R/G/B 값을 조정합니다 . • 내장된 진단 도구를 실행합니다 . 모니터에 장시간 표시된 정지 이 동안 남아 있는 미지의 잔상이 화면에 표시됨 정지 이미지의 잔상 • 모니터를 사용하지 않을 때는 전원 관리 기능을 사용하여 항상 모니터를 끕니다 ( 자세한 내용은 전원 관리 모드를 참조 ). • 또는 동적으로 변화하는 화면보호기를 사용합 니다 .
범용 직렬 버스 (USB) 관련 문제 고유의 증상 문제 가능한 해결책 USB 인터페이스 USB 주변 장치가 • 모니터 전원이 켜져 있는지 확인합니다 . 가 작동하지 않 작동하지 않습 • 업스트림 케이블을 컴퓨터에 다시 연결합니다 . 니다 습니다 • USB 주변 장치 ( 다운스트림 커넥터 ) 를 다시 연 결합니다 . • 모니터 전원을 껐다가 다시 켭니다 . • 컴퓨터를 다시 부팅합니다 . • 외장형 휴대용 HDD 와 같은 일부 USB 장치들은 더 높은 전류를 요구하므로 , 장치를 컴퓨터 시스 템에 직접 연결합니다 . 초고속 USB 3.0 초고속 USB 3.0 • 컴퓨터가 USB 3.0 을 지원하는지 확인합니다 . 인터페이스가 느 주변 장치가 느 • 일부 컴퓨터에는 USB 3.0, USB 2.0 및 USB 1.1 립니다 리게 작동하거나 포트가 모두 탑재되어 있습니다 . 올바른 USB 포 전혀 작동하지 트가 사용되는지 확인합니다 . 않습니다 • 업스트림 케이블을 컴퓨터에 다시 연결합니다 .
부록 경고 : 안전 지침 경고 : 본 안내서에서 설명된 것과 다르게 컨트롤 , 조정 또는 절차를 사용하 면 감전 , 전기적 위험 및 / 또는 기계적 위험에 노출될 수 있습니다 . 안전 지침에 대한 정보는 안전 , 환경 및 규제 정보 (SERI) 를 참조하십시오 . FCC 고지 ( 미국에만 해당 ) FCC 통지 및 기타 규정 정보는 www.dell.com/regulatory_compliance 에 있는 규정 준수 웹사이트를 참조하십시오 . Dell 에 연락 미국 내 고객은 800-WWW-DELL(800-999-3355) 로 전화하십시오 . 참고 : 활성 인터넷 연결이 없으면 구매 인보이스 , 포장 명세서 , 청구서 또는 Dell 제품 카탈로그에서 연락처 정보를 찾을 수 있습니다 . Dell 은 몇몇 온라인 및 전화 기반 지원과 서비스 옵션을 제공합니다 . 이용 가능 성은 나라와 제품에 따라 다르며 , 사용자의 지역에선 일부 서비스를 이용하지 못 할 수도 있습니다 . • 온라인 기술 지원 — www.