Alienware AW2720HF モニター ユーザーズ ガイド モデル:AW2720HF 規定モデル:AW2720HFb
注、注意および警告 注:「注」は、コンピューターをよりよく使いこなすための重要な情報を 表します。 注意:「注意」は指示に従わなければ、ハードウェアが故障する危険性、 またはデータが消失する危険性を示しています。 警告:「警告」は物件損害、人的被害または死亡の危険性を表します。 © 2019-2020 Dell Inc. またはその子会社。複製を禁ず。Dell、EMC、その他の商標は、Dell Inc. またはその子会社の商標です。その他の商標の所有権は各社にあります。 2020 - 12 Rev.
目次 製品の特徴 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 パッケージの内容 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 製品の特徴 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 部品とコントロールの確認. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 正面図 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9 背面図 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
VESA 壁取り付け(別売り). . . . . . . . . . . . . . . . . . . . . . . . . . . 31 モニターの操作 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 モニターを電源オンにする . . . . . . . . . . . . . . . . . . . . . . . . . . . .32 ジョイスティック コントロールの使い方 . . . . . . . . . . . . . . . .32 背面パネルのコントロールを使う . . . . . . . . . . . . . . . . . . . . . .33 オンスクリーンディスプレイ (OSD) メニューの使用. . . . . .34 メニューシステムにアクセスする . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 OSD 警告メッセージ . . . . . . . . . . . . . . . . . . . . . . . .
ユニバーサル シリアル バス (USB) 特有の問題. . . . . . . . . . .66 付録 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .68 米国連邦通信委員会 (FCC) 通告(米国内のみ)および その他規制に関する情報. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .68 Dell へのお問い合わせ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
製品の特徴 パッケージの内容 モニターには、以下に示すコンポーネントがすべて付属しています。不足し ているコンポーネントがある場合は、Dell テクニカルサポートまでお問い合 わせください。詳細は、Dell へのお問い合わせを参照してください。 注:一部のコンポーネントはオプションで、モニターに付属していませ ん。機能またはメディアには、特定の国で使用できないものもあります。 コンポーネント画像 コンポーネントの説明 モニター スタンドライザー スタンド ベース 6 | 製品の特徴
I/O カバー 電源ケーブル(国により 異なります) DisplayPort ケーブル (DisplayPort DisplayPort) HDMI ケーブル USB 3.
製品の特徴 Alienware AW2720HF モニターにはアクティブ マトリックス、薄膜トラン ジスター (TFT)、液晶ディスプレイ (LCD) および LED バックライトが搭載さ れています。モニターの機能は、以下のようになっています: • 68.
* 1 ミリ秒グレイ対グレイモードは最速モードで効果を発揮し、目立つブレを 低減して映像の反応性を高めます。ただし、このモードを選択すると、映像 が若干しかし知覚可能な程度の欠陥が生じる場合があります。システム設定 およびゲーマーのニーズはそれぞれ異なるため、Alienware はユーザーの皆様 に各モードを試してみてそれぞれに最も適した設定を選択されるようお勧め します。 部品とコントロールの確認 正面図 ラベル 説明 1 ケーブル管理スロット (スタンドの正面側) 2 電源オン / オフボタン (LED インジケーター 付き) 使用 ケーブルを整理するために使用します。 モニターをオン / オフにします。 水色に点灯すると、モニターの電源が入っ ており性能が正常であることを意味してい ます。白く点滅しているときには、モニ ターがスタンバイモード。 製品の特徴 | 9
背面図 モニタースタンドなし背面図 背面図(モニターのスタンド付き) ラベル 説明 1 ジョイスティック 使用 OSD メニューを操作するために使用 します。 2 機能ボタン 詳細は、モニターの操作を参照して ください。 3 バーコード、シリアル番号、 サービスタグ ラベル 技術サポートを受けるには、Dell に お問い合わせください。 4 ケーブル管理クリップ ケーブルを整理するために使用しま す。 5 スタンドリリースボタン スタンドをモニターから外します。 10 | 製品の特徴
6 VESA 取り付け穴(100 mm x VESA 互換の壁取付キットを使う壁 100 mm - VESA カバーの背面)取付モニター (100 mm x 100 mm)。 7 規制ラベル 規制承認を表示します。 8 照明ドック コネクター モニターにスタンドライザを取り付 けた状態のとき、スタンドの照明に 給電します。 9 ケーブル管理スロット(スタ ンドの背面) このスロットにケーブルを通して整 理します。 10 I/O カバー I/O ポートを保護します。 背面および底面 モニタースタンドなしの背面および底面図 ラベル 説明 1 電源コネクター 2 使用 電源ケーブルを接続します(モニター付 属)。 USB アップストリーム USB ケーブル(モニター付属)をこのポー ポート トとコンピューター繋ぎ、モニターの USB ポートを有効にします。 3、6 USB ダウンストリーム USB デバイスを接続します。* ポート (3) 注:これらのポートを使用するには、モニ ターの USB アップストリーム ポートとコ ンピューターに USB ケーブル(モニター付 属)を接続
4 充電機能付き USB ダウ USB デバイスを充電します。 ンストリーム ポート 5 ヘッドフォン ポート ヘッドフォンまたはスピーカーを接続しま す。 注意:音量調整またはイコライザでオー ディオ出力を 50% 以上上げると、ヘッド フォンの出力電圧も上がり、そのため音圧 レベルも上がります。 7 HDMI ポート (HDMI 1) コンピューターに HDMI ケーブルを接続し てください(モニター付属)。 8 9 HDMI ポート (HDMI 2) コンピューターに HDMI ケーブルを接続し てください(モニター付属)。 DisplayPort コンピューターに DisplayPort-DisplayPort ケーブルを接続してください(モニター付 属) 。 10 出力ポート スピーカーに接続してください。 注:このポートはヘッドフォンには対応し ていません。 * 信号障害を防止するために、ワイヤレス USB デバイスを USB ダウンスト リーム ポートに接続しているときには、他の USB デバイスを隣のポートに繋 ぐことはお勧めしません。 12 | 製品の特徴
モニター仕様 モデル AW2720HF スクリーン タイプ 有効マトリックス - TFT LCD パネルテクノロジー 高速 IPS 16:9 アスペクト比 表示可能画像 対角 685.0 mm(27 インチ) 幅(有効エリア) 596.7 mm(23.49 インチ) 縦(有効エリア) 335.7 mm(13.22 インチ) 合計エリア 200302.8 mm2(310.47 インチ 2) 0.3108 mm x 0.
内蔵デバイス • USB 3.0 高速ハブ(1 USB 3.0 アップストリーム ポート付き) • 4 x USB 3.0 ダウンストリーム ポート(充電に対 応する 1 個のポートを含みます) • 1 x DisplayPort バージョン 1.2(背面) 接続性 • 2 x HDMI ポートバージョン 2.0(背面) • 1 x USB 3.0 アップストリームポート(背面) • 4 x USB 3.0 ダウンストリームポート(底面:2、 背面:2) • 1 x ヘッドフォンポート(底面) • 1 x オーディオ出力ポート(背面) 境界幅(モニターの端からアクティブ エリアまで) 8.0 mm 上 左/右 8.0 mm/8.0 mm 下 23.2 mm 調整 高さ調整スタンド 0 ~ 130 mm 傾き スイベル -5° ~ 21° ピボット Dell Display Manager (DDM) 対応 -90° ~ 90° -20° ~ 20° 簡単配列とその他の主要機能 解像度仕様 モデル AW2720HF 水平走査幅 • DisplayPort 1.
ビデオのサポートモード AW2720HF モデル ビデオディスプレイ機能 (HDMI & DisplayPort 再生) 480i、480p、576i、576p、720p、1080i、 1080p、FHD 事前設定ディスプレイ モード ディスプレイ モード 水平周波数 (kHz) 垂直周波数 (Hz) 周波数 (MHz) 同期極 (水平 / 垂直) VESA、640 x 480 31.5 60.0 25.2 -/- VESA、640 x 480 37.5 75.0 31.5 -/- IBM、720 x 400 31.5 70.0 28.3 -/+ VESA、800 x 600 37.9 60.0 40.0 +/+ VESA、800 x 600 46.9 75.0 49.5 +/+ VESA、1024 x 768 64.0 60.0 108.0 -/- VESA、1024 x 768 80.0 75.0 135.0 +/+ VESA、1152 x 864 60.0 60.0 108.
電気的仕様 モデル AW2720HF ビデオ入力信号 HDMI 2.0*/DisplayPort 1.2、各差動線路毎に 600 mV、作動ペアあたり 100 ohm 入力インピー ダンス AC 入力電圧 / 周波数 / 電流 100 VAC から 240 VAC / 50 Hz または 60 Hz + 3 Hz / 1.5 A(標準) インラッシュ電流 • 120 V:30 A(最大)(0°C で)(コールドス タート) • 220 V:60 A(最大)(0°C で)(コールドス タート) 電源消費 • 0.2 W(オフモード)1 • 0.2 W(スタンバイモード)1 • 22.4 W(オンモード)1 • 73 W(最大)2 • 20.78 W (Pon)3 • 65.59 kWh (TEC)3 * Consumer Electronics Control (CEC)、HDMI Ethernet Channel (HEC)、Audio Return Channel (ARC)、3D フォーマットの規格および解像度、4K デジタルシ ネマ解像度の規格など、HDMI 2.
物理特性 モデル AW2720HF 信号ケーブル タイプ • デジタル:HDMI、19 ピン • デジタル:DisplayPort、20 ピン • ユニバーサル シリアル バス:USB、 9 ピン 注:Dell モニターは、本機に付属するビデオケーブルを使用したときに最高 の性能を発揮するよう設計されています。Dell はこれ以外のケーブル製造会 社の製品について、素材、コネクター、これらのケーブルの生産工程等の点 において責任を負うことができません。そのため、Dell は Dell モニターに付 属しないケーブルのビデオ性能については保証いたしかねます。 寸法(スタンド付き) 高さ(引き伸ばし時) 559.4 mm(22.02 インチ) 高さ(圧縮) 443.1 mm(17.45 インチ) 幅 612.7 mm(24.12 インチ) 奥行き 251.9 mm(9.92 インチ) 寸法(スタンドなし) 高さ 366.8 mm(14.44 インチ) 幅 612.7 mm(24.12 インチ) 奥行き 78.7 mm(3.
スタンド アセンブリの重さ 3.7 kg (8.16 lb) フロント フレーム(ツヤあり)17 + 3(正面のみ) 環境特性 AW2720HF モデル 準拠規格 パネルのみ無ヒ素ガラスかつ無水銀です 温度 運転時 0°C ~ 40°C (32°F ~ 104°F) 非運転時 • ストレージ:-20°C ~ 60°C (-4°F ~ 140°F) • 輸送時:-20°C ~ 60°C (-4°F ~ 140°F) 湿度 運転時 10% ~ 80%(結露しないこと) 非運転時 • ストレージ:5% ~ 90%(結露しないこと) • 輸送時:5% ~ 90%(結露しないこと) 高度 運転時 5,000 m (16,404 ft)(最大) 非運転時 12,192 m (40,000 ft)(最大) 熱発散 • 221.8 BTU/ 時(最大) • 60.
ピン割当 DisplayPort コネクター ピン数 接続した信号ケーブルの 20 ピン側 1 ML3 (n) 2 GND 3 ML3 (p) 4 ML2 (n) 5 GND 6 ML2 (p) 7 ML1 (n) 8 GND 9 ML1 (p) 10 ML0 (n) 11 GND 12 ML0 (p) 13 GND 14 GND 15 AUX (p) 16 GND 17 AUX (n) 18 ホットプラグ検出 19 Re-PWR 20 +3.
HDMI コネクター ピン数 20 | 接続した信号ケーブルの 19 ピン側 1 TMDS データ 2+ 2 TMDS データ 2 シールド 3 TMDS データ 2- 4 TMDS データ 1+ 5 TMDS データ 1 シールド 6 TMDS データ 1- 7 TMDS データ 0+ 8 TMDS データ 0 シールド 9 TMDS データ 0- 10 TMDS クロック + 11 TMDS クロックシールド 12 TMDS クロック - 13 CEC 14 予約済み(デバイスの N.C.
プラグ アンド プレイ機能 プラグ アンド プレイ互換システムで、モニターを接続することができます。 モニターがディスプレイ データ チャンネル (DDC) プロトコルを使って、コ ンピューターシステムに拡張ディスプレイ特定データ (EDID) を自動的に提供 するため、システムが、自己設定により、モニター設定を最適化します。ほ とんどのモニターインストールは自動で行われます。必要に応じて異なる設 定を選択できます。モニター設定の変更の詳細については、モニターの操作 を参照してください。 ユニバーサル シリアル バス (USB) インターフェース 本項では、モニターで使用できる USB ポートについて説明します。 注:このモニターは超高速 USB 3.0 互換です。 転送速度 データ率 電源消費 * 超高速 5 Gbps 4.5 W(最大、各ポート) 高速 480 Mbps 4.5 W(最大、各ポート) 全速度 12 Mbps 4.
6 SSTX+ 7 GND 8 SSRX- 9 SSRX+ USB ダウンストリームコネクター ピン数 9 ピン(コネクターの 側面に表示) 1 VCC 2 D- 3 D+ 4 GND 5 SSRX- 6 SSRX+ 7 GND 8 SSTX- 9 SSTX+ USB ポート • 1 x アップストリーム - 背面 • 2 x ダウンストリーム - 背面 • 2 x ダウンストリーム - 底面 充電ポート アイコンが示されたポート。BC1.2 互換機器使用時 に最大 2 A の高速充電に対応。 注:USB 3.0 機能には USB 3.
LCD モニター品質とピクセルポリシー LCD モニターの製造プロセスにおいて、いくつかのピクセルが特定の状態に 固定されることはよくあります。見つけにくく、表示品質および使い勝手に 影響しません。Dell 社のモニターの品質とピクセルに関する方針の詳細は、 www.dell.
モニターのセットアップ スタンドを取り付ける 注:スタンドは出荷時には設置されていません。 注:次の手順は、モニター付属のスタンドを接続するためだけの説明で す。スタンドを別途購入された場合は、そのスタンドの説明書にしたがっ て設置してください。 注意:湾曲したスクリーンを保護するために、設置の手順にしたがってく ださい。次の手順にしたがって、設置を完了してください。 1. ゆっくりとスタンドライザーとスタンドベースを発砲スチロールから取 り出します。 2. スタンドライザーをスタンドベースに合わせます。 3. スタンドベースの底面にあるネジハンドルを起こし、右に回してスタン ドを安定させます。 4.
5. モニターの VESA スロットが見えるようにモニターの保護カバーを開き ます。 注意:スタンドをディスプレイに取り付ける場合は、スタンドライザーを ディスプレイのバックパネルに直接設置しないでください。スタンドのポ ゴピンが正しく合致せず壊れてしまう場合があります。 6.
7. スタンドのケーブル整理用スロットとディスプレイの背面にあるケーブ ル整理用クリップに電源ケーブルを通します。 8. モニターに電源ケーブルを接続します。 9.
10. スタンドライザーを持ってモニターをゆっくりと持ち上げて、平坦な面 に置きます。 注意:事故を防止するために、モニターを持ち上げる際はスタンドライ ザーをしっかりと持ってください。 11.
12. I/O カバーのタブがディスプレイバックカバーのスロットにしっか りと 収まるようにスライドさせます。 注:ケーブルが邪魔にならないように、すべてのケーブルを I/O カバー とスタンドライザーのケーブル整理用スロットに通してください。 コンピューターの接続 警告:このセクションで手続きをはじめる前に、安全指示に従ってくださ い。 注:すべてのケーブルを同時にコンピューターに接続しないでください。 注:画像は、実例を示す目的で使用されます。コンピューターの外観は変 わることがあります。 モニターをコンピューターに接続する: 1.
2. USB 3.0 アップストリームケーブルの片方をコンピューター上の適切な USB 3.0 ポートに接続します。 3. USB 3.0 周辺機器をモニターの USB 3.0 ダウンストリーム ポートに接続 します。 4. コンピューターとモニターの電源ケーブルを壁のコンセントに差し込み ます。 5. モニターおよびコンピューターの電源をオンにします。 モニターに画像が表示されたら、インストールは完了します。画像が表 示されない場合は、よくある問題を参照してください。 モニタースタンドを取り外す 注:台を取り外している間にディスプレイに傷が付かないように、モニ ターは必ずきれいな面に置くようにしてください。 注:次の手順は、モニター付属のスタンドを接続するための説明です。ス タンドを別途購入された場合は、そのスタンドの説明書にしたがって設置 してください。 スタンドを取り外すには: 1. モニターの電源を切ります。 2. コンピューターからケーブルを外します。 3. 柔らかい布またはクッションの上にモニターを置きます。 4.
5. ケーブルをモニターから外し、スタンドライザーのケーブル整理用ス ロットから外します。 6. スタンドリリースボタンを押し下げます。 7.
VESA 壁取り付け(別売り) (ネジの寸法:M4 x 10 mm) VESA 互換壁取り付けキットに付いている使用説明書を参照してください。 1. モニターのパネルを、安定した平らな場所に置いた軟らかい布または クッションの上に置きます。 2. モニタースタンドを取り外します。(モニタースタンドを取り外すを参照 してください。) 3. プラス ドライバーを使って、プラスチック カバーを固定している 4 つの ネジを外します。 4. 壁取り付けキットのブラケットをモニターに取り付けます。 5. モニターを壁に取り付けます。詳細は、壁取り付けキットの説明書をお 読みください。 注:18.
モニターの操作 モニターを電源オンにする 電源ボタンを押してモニターをオンにします。 ジョイスティック コントロールの使い方 モニター背面にあるジョイスティック コントロールで OSD を調整します。 1. ジョイスティックボタンを押すと、OSD メインメニューが起動します。 2. ジョイスティックを上 / 下 / 左 / 右に動かして、オプションを移動しま す。 3.
• 2 方向ナビゲーション(左右)です。 • 右に動かすとサブメニューが表示されます。 • 左に動かすとサブメニューが終了します。 • 選択したメニュー項目の値を上げたり(右)、下げたり(左) します。 • 2 方向ナビゲーション(上下)です。 • メニュー項目を切り替えます。 • 選択したメニュー項目の値を上げたり(上)、下げたり(下) します。 背面パネルのコントロールを使う モニターの背面にあるコントロールボタンを使って、OSD メニューとショー トカットキーにアクセスします。 背面パネルのボタンについては、次の表にまとめてあります: 背面パネルボタン 1 説明 OSD メインメニューを開きます。メニューシステ ムにアクセスするを参照してください。 メニュー 2 OSD メインメニューを終了します。 終了 3 プリセットリストからカラーモードを指定します。 ショートカットキー / プリ セットモード モニターの操作 | 33
4 暗さスタビライザーの調整スライダーに直接アク セスできます。 ショートカットキー / 暗さ スタビライザー 5 輝度 / コントラストの調整スライダーに直接アク セスできます。 ショートカットキー / 輝度 / コントラスト これらのボタンをどれでも押すと(ジョイスティックのボタンを含まない)、 一部の OSD 機能の現設定がわかるように OSD 状態バーが表示されます。 オンスクリーンディスプレイ (OSD) メニューの使用 メニューシステムにアクセスする アイ コン メニューとサブ メニュー ゲーム 34 | モニターの操作 説明 ビジュアルゲームプレイ体験を個人化できます。
プリセット モード プリセット カラー モードのリストから選択するできます。 • 標準:モニターのデフォルトの色設定をロードします。 これは、デフォルトのプリセットモードです。 • FPS:ファーストパーソン・シューティング (FPS) ゲー ムに適したカラー設定を読み込みます。 • MOBA/RTS:マルチプレイヤーオンラインバトルアリー ナ (MOBA) やリアルタイムストラテジー (RTS) ゲームに 適したカラー設定を読み込みます。 • RPG:ロールプレイイングゲーム (RPG) に適したカラー 設定を読み込みます。 • SPORTS:スポーツゲームに適したカラー設定を読み込 みます。 • ゲーム 1/ ゲーム 2/ ゲーム 3:ゲーミングの必要性に応 じて色設定をカスタマイズできます。 • ComfortView:スクリーンから放射されるブルーライト のレベルを軽減させ、スクリーンを見やすくします。 警告:モニターから放出されるブルーライトを長 時間見続けると、デジタルアイ、眼精疲労を含め、 目に影響を与えます。長時間モニターを見続ける と、首、腕、背中、肩など身体に痛みが生じる場 合があり
プリセット モード 4. 休憩中はモニターから目を離し、20 フィート 先にあ る物を 20 秒以上見つめてください。 5.
暗さスタビライ 暗めのゲームシナリオにおいて、見やすさを向上させます。 ザー 値を高くするほど (0 ~ 3)、表示された映像の暗いエリアが 見やすくなります。 色相 この機能により、ビデオ画像の色は緑または紫にシフトし ます。色相は、望ましいフレッシュな色調を調整するため に使用されます。 ジョイスティックを使って、色相レベルを 0 から 100 の範 囲で調整します。 ジョイスティックを上に動かしてビデオ画像の緑の影を増 加します。 ジョイスティックを下に動かしてビデオ画像の紫の影を増 加します。 注:色相調整は、FPS、MOBA/RTS、SPORTS、RPG 等の プリセットモードでのみ使用できます。 彩度 この機能は、ビデオ画像の色の彩度を調整します。 ジョイスティックを使って、彩度レベルを 0 から 100 の範 囲で調整します。 ジョイスティックを上に動かしてビデオ画像の色鮮やかな 外見を増加します。 ジョイスティックを下に動かしてビデオ画像のモノクロさ を増加します。 注:彩度調整は、FPS、MOBA/RTS、SPORTS、RPG 等の プリセットモードでのみ使用できます。 ゲームを
入力信号 入力信号メニューを使って、モニターに接続されたさまざ まなビデオ信号を選択します。 DP DisplayPort (DP) コネクターを使用しているとき、DP 入力 を選択します。ジョイスティックボタンを押して、選択内 容を確定します。 HDMI 1 HDMI コネクターを使用しているとき、HDMI 1 または HDMI 2 入力を選択します。ジョイスティックボタンを押し て、選択内容を確定します。 HDMI 2 自動選択 入力信号のリ セット 38 | モニターの操作 これをオンにすると、モニターが自動的に使用可能な入力 信号をスキャンします。ジョイスティックボタンを押して、 選択内容を確定します。 入力信号メニューのすべての設定を初期値に戻します。
AlienFX 照明 色 このメニューでは電源ボタン、Alienware ロゴ、スタンドの ライトストライプの LED ライトの設定を調整します。 LED 照明の色を指定するには、オンを選択してジョイス ティックを下に動かして、ユーザーカラーオプションを選 択します。 次に、ジョイスティックを上または下に動かして、20 色の リストから色を選択します。 モニターの操作 | 39
次の表は、20 色の LED カラーで使用されるカラー番号と RGB コードをまとめたものです。 番号 R G B 1 0 0 0 2 100 0 240 3 144 0 240 4 240 0 240 5 240 0 176 6 240 0 112 7 240 0 0 8 240 80 0 9 240 128 0 10 240 224 0 11 120 240 0 12 160 240 0 13 100 245 35 14 0 240 0 15 0 240 85 16 70 240 145 17 0 240 240 18 0 160 240 19 0 96 240 20 0 0 240 AlienFX 照明機能をオフにするには、オフを選択します。 注:これらの機能は、スペクトラムを無効にしたときにし か使用できません。 カスタム 40 | モニターの操作 読み取り専用メニューです。色やスペクトラムを使って LED 照明の調整を行う場合
スペクトラム オンを選択すると、LED 照明が強くなり、赤、オレンジ、 黄、緑、青、濃紺、紫の順番で色が変わります。 AlienFX 照明を AlienFX 照明メニューのすべての設定を初期値に戻します。 リセット ディスプレイ 輝度 ディスプレイを使って画像を調整します。 輝度は、バックライトの輝度を調整します。 輝度を上げるには ジョイスティックを上に動かします。ま たは、輝度を下げるには ジョイスティックを下に動かしま す(最小 0/ 最大 100)。 コントラスト まず輝度を調整し、それでも調整が必要な場合のみコント ラストを調整します。 コントラストを上げるには ジョイスティックを上に動かし ます。または、コントラストを下げるには ジョイスティッ クを下に動かします(最小 0/ 最大 100)。 コントラスト機能は、モニターの画面の暗い部分と明るい 部分の違いの程度を調整します。 アスペクト比 画像の比率はワイド 16:9、自動サイズ変更、4:3、1:1 に設 定できます。 モニターの操作 | 41
入力カラー形式 ビデオ入力モードを次のように設定できます: RGB:モニターが DP または HDMI ケーブルを使用してコ ンピューターまたはメディアプレーヤーに接続されている 場合は、このオプションを選択します。 YPbPr:メディアプレーヤーが YPbPr 出力しかサポートし ていない場合は、このオプションを選択してください。 シャープネス この機能を使って、画像をよりシャープにまたはソフトに します。ジョイスティックを使って、シャープネスレベル を 0 から 100 の範囲で調整します。 画面のリセット ディスプレイメニューですべての設定を初期値に戻します。 オーディオ 音量 ヘッドフォンの出力音量を確認できます。 ジョイスティックを使って、音量レベルを 0 から 100 の範 囲で調整します。 オーディオのリ オーディオメニューのすべての設定を初期値に戻します。 セット メニュー 42 | モニターの操作 このオプションを選択して、OSD の言語、メニューが画面 に表示されている時間など、OSD の設定を調整します。
言語 OSD ディスプレイを 8 つの言語(英語、スペイン語、フラ ンス語、ドイツ語、ブラジルポルトガル語、ロシア語、簡 体字中国語、日本語)の 1 つに設定する言語オプション。 透明度 このオプションを選択し、ジョイスティックを上または下 に動かしてメニュー透明化を変更します(最小 0 / 最大 100)。 タイマー ジョイスティックを動かすか、ボタンを押した後、OSD が 有効になっている時間の長さを設定します。 ジョイスティック使ってスライダーを 5 ~ 60 秒まで、1 秒 刻みで調整します。 メニューのリ セット メニューメニューのすべての設定を初期値に戻します。 カスタマイズ ショートカット プリセットモード、ゲーム向上モード、AMD FreeSync キー 1 Premium、暗さスタビライザー、輝度 / コントラスト、 ショートカット 入力信号、アスペクト比、音量の中から機能を選択し、そ れをショートカットキーとして設定することができます。 キー 2 ショートカット キー 3 USB モニターがスタンバイ モードのときに、USB 機能を有効 / 無効にすることができます。
その他 ディスプレー 情報 DDC/CI モニターの現在の設定が表示されます。 DDC/CI(ディスプレイ データチャンネル / コマンド イン ターフェイス)により、コンピューターのソフトウェアを 介してモニターのパラメーター(輝度、色バランスなど) を調整します。 オフを選択すると、この機能が無効になります。 ユーザー体験を最大限に高め、モニターのパフォーマンス を最適にする場合、この機能を有効にします。 44 | モニターの操作
LCD コンディ 画像保持の微細な問題を軽減します。画像保持の程度に ショニング よっては、プログラムが実行されるまでに少し時間がかか ることがあります。オンを選択することで、この機能を有 効にできます。 ファームウェア モニターのファームウェアバージョンを表示します。 サービスタグ モニターのサービスタグを表示します。このタグは、Dell のホームページ等で電話サポートを依頼したり、保証状況 を確認したり、ドライバをアップデートしたりするときに 必要です。 他をリセット その他メニューですべての設定を初期値に戻します。 工場リセット すべての OSD 設定を工場出荷時の値にリセットします。 OSD 警告メッセージ モニターが特定の解像度モードをサポートしていないとき、次のメッセージ が表示されます: 注:接続した入力信号によっては、メッセージが異なる場合があります。 これは、モニターがコンピューターから受信している信号と同期できないこ とを意味します。このモニターが使用できる水平および垂直周波数幅につい ては、モニター仕様を参照してください。推奨モードは、1920 x 1080 画素 です。
DDC/CI 機能が無効になる前に、次のメッセージが表示されます: 初めて輝度レベルを調整するとき、次のメッセージが表示されます: 注:はいを選択すると、次回輝度設定を変更しようとしてもこのメッセー ジは表示されません。 初めて USB をスタンバイモード時はオンに設定すると、次のメッセージが表 示されます: 注:はいを選択すると、次回 USB 設定を変更しようとしてもこのメッ セージは表示されません。 46 | モニターの操作
モニターがスタンバイモードに入ると、次のメッセージが表示されます: コンピューターを有効にして、モニターを立ち上げ、OSD にアクセスしま す。 注:接続した入力信号によっては、メッセージが異なる場合があります。 電源ボタン以外のボタンを押すと、選択した入力によって次のメッセージが 表示されます: 注:接続した入力信号によっては、メッセージが異なる場合があります。 HDMI または DP 入力が選択されているが相当するケーブルが接続されていな い場合、以下のような浮動ダイアログボックスが表示されます。 注:接続した入力信号によっては、メッセージが異なる場合があります。 モニターの操作 | 47
工場リセットを選択すると、次のメッセージが表示されます: 詳細は、問題を解決するを参照してください。 リアパネルのコントロールボタンをロックする リアパネルのコントロールボタンをロックして、OSD メニューや電源ボタン へのアクセスを防止します。 ボタンをロックする: 1. ボタン 5 を 4 秒間押すと、スクリーンにメニューが開きます。 2.
最大解像度を設定する モニターの最大解像度を設定するには: Windows 7、Windows 8、Windows 8.1: 1. Windows 8 および Windows 8.1 専用です。デスクトップ タイルを選択し て、クラシック デスクトップに切り替えます。 2. デスクトップで右クリックして、画面の解像度をクリックします。 3. 画面の解像度のドロップダウン リストをクリックし、1920 x 1080 を選 択します。 4. OK をクリックします。 Windows 10: 1. デスクトップ上を右クリックし、ディスプレイの設定をクリックします。 2. ディスプレイの詳細設定をクリックします。 3. 解像度のドロップダウン リストをクリックし、1920 x 1080 を選択しま す。 4. 適用をクリックします。 オプションとして 1920 x 1080 がない場合は、グラフィック ドライバを更新 する必要があります。コンピューターによっては、以下の手順のいずれかを 完了してください: Dell デスクトップまたはラップトップをご使用の場合: • www.dell.
傾き、旋回、垂直に伸ばす 注:次の手順は、モニター付属のスタンドを接続するための説明です。ス タンドを別途購入された場合は、そのスタンドの説明書にしたがって設置 してください。 左右上下の傾斜 モニターにスタンドを取り付けると、モニターを最も快適な角度に傾斜させ たり、向きを変えたりすることができます。 注:スタンドは出荷時には設置されていません。 垂直に伸ばす 注:スタンドは、垂直に最大 130 mm 伸ばせます。下の図で、伸ばし方を 示します。 50 | モニターの操作
モニターの回転 モニターを回転させる前に、モニターが垂直に拡張している(垂直拡張)か、 またはモニターの底部エッジの傾きを避けるために傾けてあるかいずれかに なっています。 右回転 モニターの操作 | 51
左回転 注:Dell コンピューターでディスプレイ回転機能(横対縦表示)を使用す るには、このモニターに含まれていない最新のグラフィックスドライバが 必要です。最新のグラフィックスドライバをダウンロードして更新するに は、www.dell.com/support に移動し、ビデオドライバのダウンロードセ クションを参照してください。 注:縦表示モードに入っているとき、グラフィックを大量に使用する アプリケーション(3D ゲームなど)でパフォーマンスが落ちることがあ ります。 システムのディスプレイ回転設定の調整 モニターを回転させた後、以下の手順でシステムのディスプレイの回転設定 を調整する必要があります。 注:Dell コンピューター以外でモニターを使用している場合、グラフィッ プスドライバのウェブサイトまたはお使いのコンピューターの製造元ウェ ブサイトに進み、オペレーティングシステムの回転についての情報を確認 します。 ディスプレイの回転設定を調整するには: 1. デスクトップ上を右クリックした後、プロパティをクリックします。 2. 設定タブを選択し、詳細設定をクリックします。 3.
5. Intel® グラフィックスカードを使っている場合は、Intel グラフィックス タブを選択して、グラフィックスプロパティをクリックし、回転タブを 選択し、次にお気に入りの回転を設定します。 注:回転オプションがない場合、または正常に作動しない場合は、 www.dell.
AlienFX アプリケーションの使い方 AWCC (Alienware Command Center) の AlienFX を使用すると、複数の個別 ゾーンの LED 照明効果を同時に構成することができます。 注:Alienware Gaming デスクトップまたはラップトップをお持ちの場合 は、AWCC で照明を直接調整することもできます。 注:詳細は、Alienware Command Center のオンラインヘルプをご覧くだ さい。 必要条件 非 Alienware システムに AWCC をインストールする前に: • コンピューターの OS が Windows 10 R3 以上であることを確認してくだ さい。 • インターネット接続が有効になっていることを確認します。 • 付属の USB ケーブルで Alienware モニターとコンピューターが接続され ていることを確認してください。 Windows アップデートで AWCC をインストールする 1. AWCC アプリケーションはダウンロードしてありますので、自動的にイ ンストールされます。インストールに要する時間は数分です。 2.
3. セットアップファイルをダブルクリックし、画面の指示に従ってインス トールを完了してください。 AlienFX 画面について Alienware Command Center では、AlienFX を使用して Alienware モニターの LED の色やトランジション効果を調整することができます。 AWCC ホーム画面で上のメニューバーにある FX をクリックすると、AlienFX のホーム画面が開きます。 次の表は、ホーム画面の性能と機能について説明したものです。 番号 機能 説明 A CREATE NEW THEME...(新しい テーマの作成 ...
F ヘルプ AWCC オンラインヘルプを開きます。 G ウィンドウ コント ロール ウィンドウのサイズを最小化、最大化、復元でき ます。 を選択すると、アプリケーションは終了し ます。 テーマのカスタマイズを開始するときに、次の画面が表示されます。 次の表は、画面の性能と機能について説明したものです。 番号 H 機能 LIGHTING(照明) パネル 説明 このパネルのコントロールは、テーマの照明効果を設 定するためのものです。 詳細は、照明効果の設定を参照してください。 I SAVE THEME(テー テーマの調整内容と変更内容がすべて保存されます。 マを保存) J ライブプレビュー 56 | 照明ゾーンには番号が付いています。画像の番号をク リックすると、1 つのゾーンを選択できます。照明 を調整すると、モニターのプレビューには同時に新し い効果が表示されます。 AlienFX アプリケーションの使い方
テーマの作成 気に入った照明設定でテーマを作成する: 1. AWCC を起動します。 2. 上のメニューバーで FX をクリックすると、AlienFX のホーム画面にアク セスします。 3. 画面の左上隅にある をクリックして、新しいテーマを作成します。 4. CREATE NEW THEME(新しいテーマの作成) 欄にテーマの名前を入力しま す。 5. 調整したい照明ゾーンを指定します。 • ライブプレビュー エリア上のゾーンのチェックボックスを選択します。 または、 • モニターの画像の数字部分をクリックします。 6. LIGHTING(照明)パネルで、ドロップダウンリストから Morph(モー フ)、Pulse(パルス)、Color(色)、Spectrum(スペクトラム)、 Breathing(かすかに点灯)のうち好きな効果を選択します。詳細は、照 明効果の設定を参照してください。 注:Spectrum(スペクトラム)オプションは、照明を調整するために All Zones(すべてのゾーン)を選択した場合にのみ使用できます。 7.
照明効果の設定 LIGHTING(照明)パネルには、さまざまな照明効果があります。Effect(効 果)をクリックすると、使用可能なオプションが示されたドロップダウン メ ニューが開きます。 注:表示されるオプションは、指定した照明ゾーンにより異なります。 各オプションの概要については次の表をご覧ください: Morph(モーフ) 説明 ある色から別の色に自然に滑らかに変化する効果 です。 調整する: 1. カラーパレットまたは PRESET COLORS (プリセットカラー)から色を選択します。 選択した色と、その RGB カラーコードが右 側に表示されます。 注:色を変えるには、R/G/B 欄の横にある上向き および下向きの矢印ボタンを使って色コードを編 集します。 2. 選択した色をいつでも簡単にアクセスでき るように YOUR COLOR(あなたの色)リ ストに追加するには、 をクリックします。 リストには最大 12 色を追加できます。 注:リストから色を削除するには、その色を右ク リックします。 3. 上記の手順を繰り返して、Color 2(色 2) が終了照明色になるように設定します。 4.
Pulse(パルス) 説明 ライトが短く点滅します。 調整する: 1. カラーパレットまたは PRESET COLORS (プリセットカラー)から色を選択します。 選択した色と、その RGB カラーコードが右 側に表示されます。 注:色を変えるには、R/G/B 欄の横にある上向き および下向きの矢印ボタンを使って色コードを編 集します。 2. 選択した色をいつでも簡単にアクセスでき るように YOUR COLOR(あなたの色)リ ストに追加するには、 をクリックします。 リストには最大 12 色を追加できます。 注:リストから色を削除するには、その色を右ク リックします。 3. BRIGHTNESS(輝度)スライダーをドラッ グして、色の明るさを調整します。 4. TEMPO(テンポ)スライダーをドラッグし て、パルス速度を調整します。 Color(色) 説明 効果は LED 照明を 1 色にします。 調整する: 1.
Spectrum(スペクトラム) 説明 スペクトラムの順番:赤、オレンジ、黄、緑、 青、濃紺、紫の順番で色が変わります。 TEMPO(テンポ)スライダーをドラッグして、 トランジション速度を調整します。 注:オプションは、照明を調整するために All Zones(すべてのゾーン)を選択した場合にのみ 使用できます。 Breathing(かすかに点灯) 説明 照明を明るい色から暗い色に変更します。 調整する: 1. カラーパレットまたは PRESET COLORS (プリセットカラー)から色を選択します。 選択した色と、その RGB カラーコードが右 側に表示されます。 注:色を変えるには、R/G/B 欄の横にある上向き および下向きの矢印ボタンを使って色コードを編 集します。 2. 選択した色をいつでも簡単にアクセスでき るように YOUR COLOR(あなたの色)リ ストに追加するには、 をクリックします。 リストには最大 12 色を追加できます。 3.
問題を解決する 警告:このセクションで手続きをはじめる前に、安全指示に従ってくだ さい。 自己テスト お使いのモニターには、自己テスト機能が装備され、適切に機能しているか どうかを確認できます。モニターとコンピューターが適切に接続されていて、 モニター スクリーンが暗い場合は、次の手順でモニター自己テストを実行し てください: 1. コンピューターとモニター両方の電源をオフにする。 2. コンピューターの後ろからビデオ ケーブルを外す。自己テストが適切に 運用できるようにするには、コンピューターの後ろからデジタルケーブ ルを外します。 3. モニターの電源をオンにする。 注:モニターがビデオ信号を検知できないが正しく作動している場合、画 面にダイアログ ボックスが(黒い背景に)表示されます。自己テストモー ドでは、電源 LED が青く(デフォルト色)点滅します。 注:ビデオ ケーブルが外されているか、または破損している場合、通常 システムの運転中、このボックスが表示されます。 4.
内蔵診断 モニターには内蔵の診断ツールが付属しており、発生している画面の異常が モニターに固有の問題か、またはコンピューターやビデオ カードに固有の問 題かを判断します。 注:内蔵の診断は、ビデオ ケーブルがプラグから抜かれ、モニターが自 己テストモードに入っているときのみ、実行できます。 内蔵診断を実行するには、以下の手順に従います: 1. 画面がきれいであること(または、画面の表面に塵粒がないこと)を確 認します。 2. スクリーンにメニューが開くまでボタン 5 を 4 秒間押します。 3. ジョイスティック コントロールを使って診断 オプションを選択し、 ジョイスティックボタンを押して診断を開始します。グレイの画面が表 示されます。 4. スクリーンに欠陥や異常がないかを確認します。 5. 赤い画面が表示されるまで再度ジョイスティックを切り替えます。 6. スクリーンに欠陥や異常がないかを確認します。 7.
よくある問題 次の表には、発生する可能性のあるモニターのよくある問題と考えられる解 決策に関する一般情報が含まれます: 一般的な症状 発生した問題 実行可能な解決策 ビデオなし / 電 画像が表示され • コンピューターにモニターを接続しているビデ ない オ ケーブルが適切に接続され、しっかり固定さ 源 LED オフ れていることを確認します。 • 他の電気機器を使用して、コンセントが正しく 機能していることを確認します。 • 電源ボタンが完全に押されていることを確認し ます。 • 入力信号メニューにより適切な入力ソースが選 択されていることを確認してください。 ビデオなし / 電源 LED オン 画像なし、また • ディスプレイメニューで輝度とコントラスト値 は輝度がない を上げます。 • モニター自己診断テスト機能チェックを実行し ます。 • ビデオ ケーブル コネクター に曲がったり破損 したピンがないか、チェックします。 • 内蔵診断を実行します。 • 入力信号メニューにより適切な入力信号が選択 されていることを確認してください。 フォーカスが 弱い 画像が不鮮明 • ビデオ拡張ケーブルを
ドット落ち LCD スクリーン • サイクル電源オン - オフ。 に明るい点が • 永久的にオフになっているピクセルがあります 入る が、これは LCD テクノロジに固有の欠陥です。 • Dell 社のモニターの品質とピクセルに関する方 針の詳細、詳細については、Dell サポートサイ ト:www.dell.
色が欠けている 画像の色が欠け • モニター自己診断テスト機能チェックを実行し ている ます。 • コンピューターにモニターを接続しているビデ オケーブルが適切に接続され、しっかり固定さ れていることを確認します。 • ビデオ ケーブル コネクター に曲がったり破損 したピンがないか、チェックします。 色違い 画像の色が正し • アプリケーションによって、ゲームメニュー くない OSD のプリセットモードの設定を変更します。 • ゲームメニュー OSD のユーザーカラーで利得 / オフセット / 色相 / 彩度値を調整してくださ い。 • 内蔵診断を実行します。 長時間モニター に静止画像を表 示したために起 こる画像の焼き 付き 表示された静止 • スクリーンが無作動状況になってから、数分で 画像のかすかな スクリーンがオフになるように設定します。こ 影が画面に表示 れらの設定は、Windows 電源オプションまたは される Mac 省エネルギー設定で調整できます。 • または、動的に変わるスクリーンセーバーを使 用します。 製品特有の問題 特定の症状 発生した問題 実行可能な解決策 スクリー
ユーザコント 画像が表示され ロールを押して ず、LED が青く も入力信号が 点灯 ない • 信号ソースをチェックします。マウスを動か すかキーボードのどれかのキーを押して、コ ンピューターが省電力モードに入っていない ことを確認します。 • 信号ケーブルが正しく差し込まれているかど うかをチェックします。必要に応じて、信号 ケーブルを差し込み直してください。 • コンピューターまたはビデオプレーヤーを再 起動します。 ピクチャが画面 ピクチャを画面の • 異なるビデオ形式により(縦横比)、モニター 全体に表示され 高さまたは幅いっ が全画面で表示できないことがあります。 ない ぱいに表示でき • 内蔵診断を実行します。 ない ユニバーサル シリアル バス (USB) 特有の問題 特定の症状 発生した問題 実行可能な解決策 USB インター USB 周辺機器が • モニターの電源がオンになっているかをチェッ クします。 フェースが作動 作動していない • アップストリーム ケーブルをコンピューターに していない 再接続します。 • USB 周辺機器(ダウンストリーム コネクター) を再接続します
ワイヤレス USB 周辺機器は、 USB 3.0 デバイ スを繋ぐと作動 を停止します ワイヤレス USB • USB 3.0 周辺機器とワイヤレス USB 受信装置 周辺機器は応答 の距離をあけます。 が遅くなるか、 • ワイヤレス USB 受信装置とワイヤレス USB 周 その周辺機器と 辺機器の距離をできるだけ短くしてください。 受信装置の距離 • USB 延長ケーブルを使って、ワイヤレス USB が短くなると作 受信装置をできるだけ USB 3.
付録 警告:安全指示 警告:このマニュアルで指定された以外のコントロール、調整、または手 順を使用すると、感電、電気的障害、または機械的障害を招く結果となり ます。 安全についての説明は、安全、環境および規制情報 (SERI) をご覧ください。 米国連邦通信委員会 (FCC) 通告(米国内のみ)およびその他規 制に関する情報 米国連邦通信委員会 (FCC) 通告(米国内のみ)およびその他規制に関する情 報に関しては、規制コンプライアンスに関するウェブページ www.dell.