Alienware AW2720HFA-skjerm Brukerhåndbok Modell: AW2720HFA Reguleringsmodell: AW2720HFb
Merknader, advarsler og advarsler MERKNAD: Et MERKNAD angir viktig informasjon som vil hjelpe deg dra bedre nytte av din datamaskin. FORSIKTIGHET: FORSIKTIGHET angir potensiell skade på maskinvaren eller tap av data hvis du ikke følger instruksjonene. ADVARSEL: En ADVARSEL angir et potensial for skade på eiendom, personskade eller død. © 2020 Dell Inc. eller dets datterselskaper. Alle rettigheter reservert. Dell, EMC og andre varemerker er varemerker for Dell Inc. eller dets datterselskaper.
Innhold Om skjermen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Pakkeinnhold. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Produktfunksjoner . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Identifisering av deler og kontroller . . . . . . . . . . . . . . . . . . . . 9 Sett forfra . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9 Sett bakfra . . . . . . . . . . . . . . . .
VESA-veggmontering (valgfritt) . . . . . . . . . . . . . . . . . . . . . . 31 Betjening av skjermen . . . . . . . . . . . . . . . . . . . . . . . . . . 32 Slå på skjermen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32 Bruke styrespakkontroll . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32 Bruk kontrollene på bakpanelet . . . . . . . . . . . . . . . . . . . . . . .33 Bruke OSD-menyen (On-Screen Display) . . . . . . . . . . . . . .34 Åpne menysystemet . . . . . . .
Produktspesifikke problemer . . . . . . . . . . . . . . . . . . . . . . . . . 67 Problemer knyttet med Universal Serial Bus (USB) . . . . . .68 Vedlegg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .69 FCC-merknader (kun USA) og annen forskriftsinformasjon . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .69 Kontakt Dell. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .69 EUs produktdatabase for energimerke og produktinformasjonsark. . .
Om skjermen Pakkeinnhold Skjermen leveres med komponentene som vises nedenfor. Hvis komponentene mangler, ta kontakt med Dells tekniske støtte. For mer informasjon, se Kontakt Dell. MERKNAD: Noen komponenter kan være valgfrie og leveres kanskje ikke med skjermen. Noen funksjoner eller medier er kanskje ikke tilgjengelige i visse land.
I/U-deksel Strømkabel (varierer fra land til land) DisplayPort-kabel (DisplayPort til DisplayPort) HDMI-kabel USB 3.
Produktfunksjoner Alienware AW2720HFA-skjermen kommer med en aktiv matrise, tynnfilmstransistor (TFT), liquid crystal display (LCD) og LED-bakgrunnslys. Monitorens funksjoner inkluderer: • 68,5 cm (27 tommer) synlig område (målt diagonalt). Oppløsning: Opptil 1920 x 1080 gjennom DisplayPort og HDMI, med støtte for fullskjerm eller lavere oppløsninger, som støtter en ekstremt høy oppdateringsfrekvens på 240 Hz.
*Grå-til-grå-modus på 1 ms kan oppnås i Extreme (Ekstrem)-modus med det formål å redusere synlig uskarphet i bevegelse og økt bildesvar. Dette kan introdusere noen små og merkbare visuelle gjenstander i bildet. Siden hvert systemoppsett og behov for hver spiller er forskjellig, er Alienwares anbefaling at du eksperimenterer de forskjellige modusene for å kunne finne innstillingen som passer for dem.
Sett bakfra Sett bakfra uten skjermstativ Sett bakfra med skjermstativ Etikett Beskrivelse Bruk 1 Styrespak Det vil brukes for å kontrollere OSDmenyen. 2 Funksjonsknapper For mer informasjon, se Betjening av skjermen. 3 Strekkode, serienummer og serviceetikett Referer til denne etiketten hvis du trenger å kontakte Dell for teknisk støtte. 4 Kabelhåndteringsklemme Å organisere kablene. 5 Knapp for frigjøring av stativ Denne knappen frigjør stativet fra skjermen.
6 VESA-monteringshull (100 mm x 100 mm - bak VESA-deksel) Monter skjermen på veggen ved å bruke VESA-kompatibelt veggmonteringssett (100 mm x 100 mm). 7 Forskriftsetikett Inneholder informasjon om forskrifter som gjelder skjermen. 8 Kontakt for lysdokk Ved festing av stativet til skjermen, vil dokken gi strøm til lyset på stativet. 9 Spor for kabelhåndtering (på baksiden av stativet) Brukes til å ordne kablene ved å føre dem gjennom sporet. 10 I/U-deksel Beskytter I/U-portene.
4 USB-nedstrømsport med Strømlading Koble til for å lade USD-en. 5 Hodetelefoner-port Koble til hodetelefoner eller høyttalere. FORSIKTIGHET: Øk lydutgangen utover 50% på volumkontrollen eller utjevneren kan øke utgangsspenningen på hodetelefonene og dermed øke lydtrykknivået. 7 HDMI-port (HDMI 1) Koble til datamaskinen med HDMI-kabelen (følger med skjermen). 8 HDMI-port (HDMI 2) Koble til datamaskinen med HDMI-kabelen (følger med skjermen).
Visningsvinkel Vertikal 178° (typisk) Horisontal 178° (typisk) Lystetthet 350 cd/m² (typisk) Kontrastforhold 1000 til 1 (typisk) Frontbelegg Antirefleksbehandling av foran polarisatoren (Haze 25%, 3H) Bakgrunnsbelysning WLED Responstid • 1 ms grå til grå i Extreme (Ekstrem)-modus* • 2 ms grå til grå i Super Fast (Superrask)-modus* • 4 ms grå til grå i Fast (Rask)-modus *Grå-til-grå-modus på 1 ms kan oppnås i Extreme (Ekstrem)-modus med det formål å redusere synlig uskarphet i bevegelse og økt b
Kantbredde (skjermkant til aktivt område) Topp 8,0 mm Venstre/Høyre 8,0 mm/8,0 mm Nederst 23,2 mm Justerbarhet Høydejusterbart stativ 0 til 130 mm Vipp -5° til 21° Sving -20° til 20° Drei -90° til 90° Kompatibilitet med Dell Enkel ordning og andre viktige funksjoner Display Manager (DDM) Spesifikasjoner for oppløsning Modell AW2720HFA Horisontal skanning • DisplayPort 1.2: 255 til 255 kHz (automatisk) • HDMI 2.0: 30 til 255 kHz (automatisk) Vertikal skanning • DisplayPort 1.
Forhåndsinnstilte skjermmodus Visningsmodus Horisontal frekvens (kHz) Vertikal frekvens (Hz) Pikselklokke (MHz) Synk polaritet (horisontal/ vertikal) VESA, 640 x 480 31,5 60,0 25,2 -/- VESA, 640 x 480 37,5 75,0 31,5 -/- IBM, 720 x 400 31,5 70,0 28,3 -/+ VESA, 800 x 600 37,9 60,0 40,0 +/+ VESA, 800 x 600 46,9 75,0 49,5 +/+ VESA, 1024 x 768 64,0 60,0 108,0 -/- VESA, 1024 x 768 80,0 75,0 135,0 +/+ VESA, 1152 x 864 60,0 60,0 108,0 +/+ VESA, 1280 x 1024 67,5 60,0 1
Elektriske spesifikasjoner Modell AW2720HFA Inngangssignaler for video HDMI 2.0/DisplayPort 1.2, 600 mV for hver differensiell linje, 100 ohm inngangsimpedans per differensialpar. AC inngangsspenning/ frekvens/strøm 100 VAC til 240 VAC / 50 Hz eller 60 Hz + 3 Hz / 1,5 A (typisk) Innkoblingsstrøm • 120 V: 30 A (maks.) ved 0°C (kald start) • 220 V: 60 A (maks.) ved 0°C (kald start) Strømforbruk • 0,2 W (Av-modus)1 • 0,2 W (Standby-modus)1 • 22,4 W (På-modus)1 • 73 W (Maks.
Fysiske egenskaper Modell AW2720HFA Signalkabeltype • Digital: HDMI, 19 pinner • Digital: DisplayPort, 20 pinner • Universell seriebuss: USB, 9 pinner MERKNAD: Dell-skjermer er utviklet for å kunne fungere optimalt med videokablene som leveres med skjermen. Dell har ingen kontroll over de forskjellige kabelleverandørene i markedet, typen materiale, kontakten og prosessen til produksjon av disse kablene, og som en konsekvens garanterer Dell ikke videoytelse på kabler som ikke leveres med Dell-skjermen.
Miljøegenskaper Modell AW2720HFA Overholdelsesstandarder Arsenfritt glass og kvikksølvfritt kun for panelet Temperatur I drift 0°C til 40°C (32°F til 104°F) Ikke i drift • Lagring: -20°C til 60°C (-4°F til 140°F) • Frakt: -20°C til 60°C (-4°F til 140°F) Luftfuktighet I drift 10% til 80% (ikke-kondenserende) Ikke i drift • Lagring: 5% til 90% (ikke-kondenserende) • Frakt: 5% til 90% (ikke-kondenserende) Høyde I drift 5000 m (16404 fot) (maksimum) Ikke i drift 12192 m (40000 fot) (maksimum) Varm
Pinnetilordning DisplayPort-kontakt Pinnenummer 20-pinners side av den tilkoblede signalkabelen 1 ML3 (n) 2 GND 3 ML3 (p) 4 ML2 (n) 5 GND 6 ML2 (p) 7 ML1 (n) 8 GND 9 ML1 (p) 10 ML0 (n) 11 GND 12 ML0 (p) 13 GND 14 GND 15 AUX (p) 16 GND 17 AUX (n) 18 Hot Plug-deteksjon 19 Re-PWR 20 +3,3 V DP_PWR Om skjermen | 19
HDMI-kontakt Pinnenummer 19-pinners side av den tilkoblede signalkabelen 1 TMDS DATA 2+ 2 TMDS DATA 2 SHIELD 3 TMDS DATA 2- 4 TMDS DATA 1+ 5 TMDS DATA 1 SHIELD 6 TMDS DATA 1- 7 TMDS DATA 0+ 8 TMDS DATA 0 SHIELD 9 TMDS DATA 0- 10 TMDS CLOCK+ 11 TMDS CLOCK SHIELD 12 TMDS CLOCK- 13 CEC 14 Reservert (N.C.
Universal Serial Bus (USB)-grensesnitt Delen inneholder informasjon om USB-portene som er tilgjengelige på skjermen. MERKNAD: Skjermen er kompatibel med Super-Speed USB 3.0. Overføringshastighet Datahastighet Strømforbruk* Super-Speed 5 Gbps 4,5 W (Maks., hver port) Høy hastighet 480 Mbps 4,5 W (Maks., hver port) Full hastighet 12 Mbps 4,5 W (Maks., hver port) *Opptil 2 A på USB-nedstrømsport (med -batteriikon) kompatible enheter med batteriladingsversjon eller normale USB-enheter.
USB-nedstrømskontakt Pinnenummer 9-pinners side av kontakten 1 VCC 2 D- 3 D+ 4 GND 5 SSRX- 6 SSRX+ 7 GND 8 SSTX- 9 SSTX+ USB-porter • 1 x oppstrøms - bak • 2 x nedstrøms - bak • 2 x nedstrøms - nederst Strømladeport - porten med -ikon; støtter opptil 2 A-hurtiglading hvis enheten er kompatibel med BC1.2. MERKNAD: USB 3.0-funksjonalitet krever en datamaskin kompatibel med USB 3.0. MERKNAD: USB-portene på skjermen fungerer kun når skjermen er slått på eller når den er i standby-modus.
LCD-skjermkvalitet og pikselretningslinjer Under produksjonsprosessen er det vanlig at en eller flere piksler blir fast i en uforanderlig tilstand. Dette er vanskelig å se og ikke påvirker skjermkvaliteten eller brukervennligheten. For mer informasjon om retningslinjer for kvalitet og piksel for Dell-skjermen, se www.dell.com/pixelguidelines. Retningslinjer for vedlikehold Rengjøring av skjermen FORSIKTIGHET: Les og følg Sikkerhetsinstruksjoner før rengjøring av skjermen.
Konfigurering av skjermen Oppsetting av stativet MERKNAD: Stativet er ikke installert fra fabrikken. MERKNAD: Følgende instruksjoner gjelder kun for stativet som leveres med skjermen. Ved festing av et stativ som kjøpes fra en annen kilde, må du alltid følge installasjonsinstruksjonene som leveres med stativet. FORSIKTIGHET: Følgende trinn er viktige for beskyttelse av den buede skjermen. Følg alltid instruksjonene nedenfor for å fullføre installasjonen. 1. Fjern stativet og stativbasen fra emballasjeputen.
5. Åpne beskyttelsesdekselet som finnes på skjermen for å kunne få tilgang til VESA-sporet som finnes på skjermen. FORSIKTIGHET: Ved tilkobling av stativsenheten til skjermen, plasser aldri stativet direkte på skjermens bakpanel. Dette kan skade pogopinnene på grunn av feiljustering. 6. Sett inn tappene som finnes på stativet i sporene på skjermens bakdeksel, og senk stativet for å kunne feste den på plass.
7. Rett strømkabelen gjennom åpningen for kabelhåndtering på stativet og deretter gjennom kabelklemmen som finnes på baksiden av skjermen. 8. Koble strømkabelen til skjermen. 9. Før de nødvendige kablene gjennom åpningen for kabelhåndtering på stativet og deretter gjennom kabelklemmen som finnes på baksiden av skjermen.
10. Hold stativet og løft monitoren forsiktig, og legg den på en flatt overflate. FORSIKTIGHET: Hold stativet godt mens skjermen løftes for å unngå utilsiktet skade. 11. Løft beskyttelsesdekselet fra skjermen.
12. Skyv tappene på I/U-dekselet inn i sporene på skjermens bakdeksel til et klikk høres. MERKNAD: Bekreft at kablene passerer gjennom I/U-dekselet og sporet for kabelhåndtering på stativet. Tilkobling av datamaskinen ADVARSEL: Før noen av prosedyrene i denne delen startes, se Sikkerhetsinstruksjoner. MERKNAD: Kablene må aldri kobles til datamaskinen på same tid. MERKNAD: Bildene brukes kun til illustrasjon. Utseendet til datamaskinen kan variere. Slik kobler du skjermen til datamaskinen: 1.
2. Koble den andre enden av USB 3.0-oppstrømskabelen til en passende USB 3.0-port som finnes på datamaskinen. 3. Koble USB 3.0-ekterne utstyr til USB 3.0-nedstrømsporter som finnes på skjermen. 4. Koble strømkablene til datamaskinen og skjermen til et stikkontakt som finnes inn i et vegguttak. 5. Slå på skjermen og datamaskinen. Hvis skjermen viser et bilde, vil installasjonen være fullført. Hvis det ikke vises noe bilde, se Vanlige problemer.
5. Koble kablene fra skjermen og skyv dem ut gjennom sporet for kabelhåndtering som finnes på stativet. 6. Trykk og hold inne utløserknappen på stativet. 7. Løft stativet og bort fra skjermen.
VESA-veggmontering (valgfritt) (Skruedimensjon: M4 x 10 mm) Se instruksjonene som følger med veggmonteringssettet som er kompatibelt med VESA. 1. Legg skjermpanelet på en myk klut eller pute på en stabil flat overflate. 2. Slik fjerner du skjermstativet. (Se Slik fjerner du skjermstativet.) 3. Bruk en stjerneskrutrekker fra Phillips og ta ut de fire skruene som fester plastdekselet. 4. Fest monteringsbraketten fra veggmonteringssettet til skjermen. 5. Monter skjermen på veggen.
Betjening av skjermen Slå på skjermen Trykk på strømknappen for å slå på skjermen. Bruke styrespakkontroll Bruk styrespakkontrollen som finnes på baksiden av skjermen og gjør OSDjusteringer. 1. Trykk på styrespak-knappen og start OSD-hovedmenyen. 2. Flytt styrespaken opp/ned/venstre/høyre for å veksle mellom alternativer. 3. Trykk på styrespak-knappen på nytt og bekreft innstillinger og avslutt.
• For navigasjon i to retninger (høyre og venstre). • Flytt til høyre for å gå til undermenyen. • Flytt til venstre for å gå ut av undermenyen. • Øker (høyre) eller reduserer (venstre) parametrene for valgt menyelement. • For navigasjon i to retninger (opp og ned). • Veksler mellom menyalternativene. • Øker (opp) eller reduserer (ned) parametrene for valgt menyelement. Bruk kontrollene på bakpanelet Bruk kontrollknappene som finnes på baksiden av skjermen og få tilgang til OSD-menyen og hurtigtaster.
4 For å få direkte tilgang til glidebryteren for justering av Dark Stabilizer (Mørk stabilisator). Hurtigtast/Dark Stabilizer (Mørk stabilisator) 5 For å få direkte tilgang til glidebryterne for justering av Brightness/Contrast (Lysstyrke/Kontrast). Hurtigtast/Brightness/ Contrast (Lysstyrke/ Kontrast) Når du trykker på noen av disse knappene (unntatt styrespak-knappen), vil OSD-statuslinjen vises og indikerer gjeldende innstillinger for noen OSDfunksjoner.
Preset Modes Du kan velge fra en liste over forhåndsinnstilte fargemoduser. (Forhåndsinnstilte moduser) • Standard: Laster inn standard fargeinnstillinger på skjermen. Dette er standard forhåndsinnstilt modus. • FPS: Laster inn farger som anses å være ideelle for førstepersonsskytespill (FPS). • MOBA/RTS: Laster inn farger som anses å være ideelle for MOBA- (Multiplayer Online Battle Arena) og sanntidsstrategispill (RTS). • RPG: Laster inn fargerinnstillinger som er ideelle for rollespill (RPG).
Preset Modes (Forhåndsinnstilte moduser) 36 | Reduser risikoen for belastning i øynene og smerter i nakke/arm/rygg/skulder som kan oppstå ved å bruke skjermen i lange perioder ved å gjøre følgende: 1. Plass skjermen på en avstand mellom 20 og 28 tommer (50 cm - 70 cm) fra øynene dine. 2. Prøv å blinke ofte for å fukte øynene eller fukte øynene med vann etter at du har brukt skjermen i lengre tid. 3. Ta regelmessige og hyppige pauser på 20 minutter annenhver time. 4.
Game Enhance Funksjonen tilbyr tre tilgjengelige funksjoner som kan brukes Mode for å forbedre din spillopplevelse. (Spillforbedring) • Off (Av) Velg og deaktiver funksjonene som finnes under Game Enhance Mode (Spillforbedring). • Timer (Tidsur) Deaktiver eller aktiver tidsuret som finnes øverst til venstre på skjermen. Timeren viser tiden som har gått. Et alternativ kan velges fra tidsintervalllisten som vil holde deg oppmerksom på gjenværende tid.
Dark Stabilizer Funksjonen forbedrer synligheten i mørke spillscenarier. (Mørk Synligheten i det mørke området på skjermbildet er bedre stabilisator) hvis verdien er høyere (mellom 0 og 3). Hue (Fargetone) Funksjonen skifter fargen på videobildet til grønn eller lilla. Denne brukes for justering av ønsket hudfarge. Bruk styrespaken og juster fargenivået fra 0 til 100. Øk den grønne fargen på videobildet ved å flytte styreskapen oppover. Øk den lilla fargen på videobildet ved å flytte styreskapen nedover.
Input Source Bruk Input Source (Inndatakilde)-menyen og velg mellom (Inndatakilde) forskjellige videosignaler som kan kobles til skjermen. DP Velg DP-inngangen ved bruk av DisplayPort (DP)-kontakten. Trykk på styrespaken og bekreft valget. HDMI 1 Velg HDMI 1- eller HDMI 2-inngangen ved bruk av HDMIkontakter. Trykk på styrespaken og bekreft valget. HDMI 2 Auto Select (Automatisk valg) Slå på funksjonen og la skjermen utføre en automatisk skanning etter tilgjengelige inngangskilder.
AlienFX Lighting (AlienFXbelysning) Bruk menyen for justering av innstillingene for LED-lys for strømknapp, Alienware-logo og lysstripe på stativet. Color (Farge) Spesifiser en LED-belysningsfarge ved å velge On (På) og flytt styrespaken for å markere alternativet Custom Color (Egendefinert farge)-alternativet. Velg deretter fra listen over 20 tilgjengelige farger ved å flytte styrespaken opp eller ned.
Color (Farge) Tabellen nedenfor viser fargenummeret og RGB-kodene som brukes for de 20 LED-fargene. Nr. R G B 1 0 0 0 2 100 0 240 3 144 0 240 4 240 0 240 5 240 0 176 6 240 0 112 7 240 0 0 8 240 80 0 9 240 128 0 10 240 224 0 11 120 240 0 12 160 240 0 13 100 245 35 14 0 240 0 15 0 240 85 16 70 240 145 17 0 240 240 18 0 160 240 19 0 96 240 20 0 0 240 Slå av AlienFX-lyset ved å velge Off (Av).
Spectrum (Spektrum) Hvis On (På) velges, vil LED lyse og endre farger i rekkefølgen av fargespekteret: rød, oransje, gul, grønn, blå, indigo og fiolett. Reset AlienFX Tilbakestiller alle innstillinger under AlienFX Lighting Lighting (AlienFX-belysning)-menyen til fabrikkstandardene. (Tilbakestill AlienFXbelysning) Display (Skjerm) Brightness (Lysstyrke) Bruk Display (Skjerm) og juster bilder. Brightness (Lysstyrke) justerer lysstyrken på bakgrunnsbelysningen.
Aspect Ratio (Sideforhold) Justerer bildeforholdet til Wide 16:9 (Bred 16:9), Auto Resize (Automatisk endring av størrelse), 4:3, eller 1:1. Input Color Lar deg stille videoinngangsmodus til: Format RGB: Velg alternativet hvis skjermen er koblet til en (Inngangsfar- datamaskin (eller mediespiller) med DP- eller HDMI-kabelen. geformat) YPbPr: Velg alternativet hvis mediespilleren kun støtter YPbPr-utgang. Sharpness (Skarphet) Funksjonen kan gjøre bildet skarpere eller mykere.
Menu (Meny) Velg dette for å kunne justere innstillingene til OSD-menyen, for eksempel språk på OSD-menyen, hvor lenge menyen forblir på skjermen, og så videre. Language (Språk) Stiller OSD-menyen til ett av de åtte språkene (engelsk, spansk, fransk, tysk, brasiliansk portugisisk, russisk, forenklet kinesisk eller japansk). Transparency Velg dette for å endre gjennomsiktigheten i menyen ved å (Gjennomsik- bevege styrespaken opp eller ned (min. 0/maks. 100).
Personalize (Tilpass) Shortcut Key 1 Lar deg velge en funksjon fra Preset Modes (Hurtigtast 1) (Forhåndsinnstilte moduser), Game Enhance Mode Shortcut Key 2 (Spillforbedring), AMD FreeSync Premium, Dark Stabilizer (Hurtigtast 2) (Mørk stabilisator), Brightness/Contrast (Lysstyrke/ Kontrast), Input Source (Inndatakilde), Aspect Ratio Shortcut Key 3 (Sideforhold), eller Volume (Volum) og angi det som en (Hurtigtast 3) hurtigtast. USB Du kan aktivere eller deaktivere USB-funksjonen i skjermens standby-modus.
DDC/CI DDC/CI (Display Data Channel/Command Interface) (Vis datakanal/kommandogrensesnitt) kan brukes til å justere skjermens parametrene (lysstyrke, fargebalanse osv.) gjennom programvaren på datamaskinen. Funksjonen kan deaktiveres ved å velge Off (Av). Aktiver funksjonen for best brukeropplevelse og optimal ytelse for skjermen. LCD Conditioning (LCDkonditionering) Firmware (Fastvare) Bidrar til å redusere mindre situasjoner med bildeforsinkelse.
Reset Others (Tilbakestill andre) Tilbakestiller alle innstillinger under Others (Andre)-menyen til fabrikkstandardene. Factory Reset Tilbakestiller alle OSD-innstillinger til fabrikkstandardene. (Tilbakestill til fabrikkinnstillinger) Advarsel på OSD-meny Hvis skjermen ikke støtter en bestemt oppløsningsmodus, vil følgende melding vises: MERKNAD: Meldingen kan variere litt i henhold til det tilkoblede inngangssignalet.
Når Brightness (Lysstyrke)-nivået justeres for første gang, vil følgende melding vises: MERKNAD: Hvis du velger Yes (Ja), vil meldingen ikke vises ved neste endring av Brightness (Lysstyrke)-innstillingen. Etter konfigurering av USB til On in Standby Mode (På i standby-modus) for første gang, vil følgende melding vises: MERKNAD: Hvis du velger Yes (Ja), vil meldingen ikke vises ved neste endring av USB-innstillingen.
Hvis du trykker på en annen knapp enn av/på-knappen, vil følgende melding vises med dette avhender av valgt inngang: MERKNAD: Meldingen kan variere litt i henhold til det tilkoblede inngangssignalet. Hvis enten HDMI- eller DP-inngang velges og den tilsvarende kabelen ikke er kobles til, vises en flytende dialogboks som vises nedenfor. MERKNAD: Meldingen kan variere litt i henhold til det tilkoblede inngangssignalet.
Låse kontrollknappene på bakpanelet Lås kontrollknappene som finnes på bakpanelet for å kunne unngå tilgang til OSD-menyen og/eller av/på-knappen. Slik låser du knappen(e): 1. Trykk og hold inne Knapp 5 i fire sekunder, og en meny vises på skjermen. 2. Velg ett av følgende alternativer: • Menu Buttons (Menyknapper): Velg dette alternativet for å låse alle OSD-menyknappene unntatt strømknappen. • Power Button (Strømknapp): Velg alternativet for å låse kun av/påknappen.
Innstilling av maksimal oppløsning Innstilling av maksimal oppløsning for skjermen: I Windows 7, Windows 8, eller Windows 8.1: 1. Kun for Windows 8 og Windows 8.1, velg Desktop for å kunne bytte til klassisk desktop. 2. Høyreklikk på desktop og klikk på Skjermoppløsning. 3. Klikk på rullegardinlisten for Skjermoppløsning og velg 1920 x 1080. 4. Klikk på OK. I Windows 10: 1. Høyreklikk på desktop og klikk på Skjerminnstillinger. 2. Klikk på Avanserte skjerminnstillinger. 3.
Anvendelse av vipp-, sving- og vertikal forlengelse MERKNAD: Følgende instruksjoner gjelder kun for festing av stativet som kommer med skjermen. Ved festing av et stativ som kjøpes fra en annen kilde, må du alltid følge installasjonsinstruksjonene som leveres med stativet. Tilt- og svingforlengelser Forutsatt at stativet er festet til skjermen, kan du vippe og svinge skjermen for å oppnå den mest komfortable synsvinkelen. MERKNAD: Stativet er ikke installert fra fabrikken.
Rotering av skjerm Før skjermen roteres, må skjermen forlenges helt vertikalt (vertikal forlengelse) og helles helt opp med det formål å unngå å treffe den nederste kanten av skjermen.
Roter mot klokken MERKNAD: For å kunne bruke Skjermrotasjon-funksjonen (Landskap versus portrettvisning) med Dell-datamaskinen, skal du ha en oppdatert grafikkdriver som ikke leveres med denne skjermen. Last ned grafikkdriveren ved å gå til www.dell.com/support, Last ned-delen for Videodrivere for siste driveroppdateringer. MERKNAD: I Portrettmodus, kan du oppleve dårlig ytelse i grafikkintensive applikasjoner (3D-spill osv.).
Justere innstillingene for skjermens rotasjon for ditt system Etter at du har rotert skjermen, må du fullføre prosedyren som nevnes nedenfor med det formål å justere innstillingene for skjermens rotasjon på systemet ditt. MERKNAD: Hvis skjermen brukes med en datamaskin som ikke er fra Dell, gå til nettstedet til grafikkdriveren eller datamaskinprodusenten og få informasjon om hvordan du roterer 'innholdet' på skjermen. Slik justerer du innstillingene for skjermens rotasjon: 1.
Bruk av AlienFX-applikasjon Konfigurer LED-lyseffektene over flere forskjellige soner på Alienware-skjermen gjennom AlienFX i AWCC (Alienware Command Center). MERKNAD: Hvis du har et Alienware Gaming-skrivebord eller -bærbar PC, har du direkte tilgang til AWCC for kontroll av lysene. MERKNAD: For mer informasjon, se Alienware Command Center Online-hjelp. Forutsetninger Før installasjon av AWCC på et ikke-Alienware-system: • Bekreft at operativsystemet på datamaskinen er Windows 10 R3 eller nyere.
3. Dobbeltklikk på oppsettfilen og følg instruksjonene på skjermen for å fullføre installasjonen. Navigere i AlienFX-vinduet Ved Alienware Command Center, kan AlienFX brukes for å kontrollere LEDlysfargene og overgangseffektene til Alienware-skjermen. På AWCC-startskjermbildet, klikk på FX i den øverste menylinjen for å gå til startskjermen til AlienFX. Følgende tabell beskriver funksjonene og funksjonene som kan finnes på startskjermen: Nr. Funksjoner Beskrivelser A CREATE NEW Klikk på THEME...
F Hjelp Klikk og få tilgang til AWCC Online-hjelp. G Vinduskontroller Bruk knappene for å minimere, maksimere eller gjenopprette vinduets størrelse. Applikasjonen lukkes når velges. Begynn å tilpasse et tema etter å se følgende skjermbilde: Følgende tabell beskriver funksjonene og funksjonene som kan finnes på skjermen: Nr. H Funksjoner Beskrivelser LIGHTING Bruk kontrollene i panelet for konfigurasjon av (BELYSNING)-panel lyseffekter for et tema. Se Innstilling av lyseffekter for flere detaljer.
Opprette et tema Opprett et tema med foretrukne lysinnstillinger: 1. Start AWCC. 2. Klikk på FX i den øverste menylinjen for å gå til startskjermen til AlienFX. 3. Klikk øverst til venstre i vinduet for å opprette et nytt tema. 4. Skriv inn temanavnet i CREATE NEW THEME (OPPRETT NYTT TEMA)tekstboksen. 5. Spesifiser belysningssoner for å gjøre lysjusteringer ved å: • velge avkrysningsrute(r) for sonen over live forhåndsvisningsområdet, eller • klikke på nummerert billedtekst på bildet av skjermen 6.
Innstilling av lyseffekter LIGHTING (BELYSNING)-panelet gir forskjellige lyseffekter. Klikk på Effect (Effekt) og åpne rullegardinmenyen med tilgjengelige alternativer. MERKNAD: Alternativene som vises varierer avhengig av lyssonen(e) som er angitt. Følgende tabell gir en oversikt over forskjellige alternativer: Morph Beskrivelser Effekten endrer lysfargen til en annen etter en sømløs overgang. Hvordan gjøre justeringene: 1.
Pulse (Puls) Beskrivelser Effekten får lyset til å blinke med en kort pause. Hvordan gjøre justeringene: 1. Velg en ønsket farge fra fargepaletten eller listen over PRESET COLORS (FORINNSTILLTE FARGER.). Den valgte fargen og RGB-fargekoder vil vises i høyre felt. MERKNAD: Endre fargen ved å bruke opp- og nedpiltastene ved siden av R/G/B-boksene og rediger fargekodene. 2. Legg til den valgte fargen i listen over YOUR COLORS (DINE FARGER) for rask tilgang ved å klikke på . 12 farger kan legges til listen.
Spectrum (Spektrum) Beskrivelser Effekten gjør at lyset endres i sekvens av spektrum: rød, oransje, gul, grønn, blå, indigo og fiolett. Dra glidebryteren TEMPO og juster overgangshastigheten. MERKNAD: Alternativet er kun tilgjengelig ved valg av All Zones (Alle soner) og juster lysene. Breathing (Puster) Beskrivelser Effekten får lyset til å skifte fra lys til ingenting. Hvordan gjøre justeringene: 1. Velg en ønsket farge fra fargepaletten eller listen over PRESET COLORS (FORINNSTILLTE FARGER.).
Feilsøking ADVARSEL: Før noen av prosedyrene i denne delen startes, se Sikkerhetsinstruksjoner. Selvtest Dell-skjermen har en selvtestfunksjon (STFC) som du kan bruke til å kontrollere om Dell-skjermen fungerer som den skal. Hvis skjermen og datamaskinen er koblet til riktig, men skjermen forblir mørk, kjører du selvtesten ved å utføre følgende trinn: 1. Slå av både skjermen og datamaskinen. 2. Koble videokabelen fra baksiden av datamaskinen.
Innebygd diagnostikk Skjermen har et innebygd diagnostikkverktøy som hjelper deg med å finne ut om skjermproblemene skyldes selve skjermen, eller datamaskinen og videokortet. MERKNAD: Den innebygde diagnosen kan kun kjøres hvis videokabelen er frakoblet og skjermen er i selvtestmodus. Start av den innebygde diagnostikken: 1. Bekreft at skjermen er ren (det er ingen støvpartikler på skjermoverflaten). 2. Trykk og hold inne Knapp 5 i fire sekunder til en meny vises på skjermen. 3.
Vanlige problemer Tabellen nedenfor inneholder generell informasjon om vanlige skjermproblemer og mulige løsninger: Vanlige symptomer Hva du opplever Mulige løsninger Ingen video/ LED av Ingen bilder • Bekreft at videokabelen som kobler til skjermen og datamaskinen er koblet på riktig måte og er sikker. • Sjekk at stikkontakten fungerer på riktig måte ved å bruke et annet elektrisk utstyr. • Bekreft at strømknappen er trykket ned.
Piksler låst på LCD-skjermen har lyse flekker • Slå strømmen av og på. • Piksler som er permanent av er en naturlig feil som kan oppstå i LCD-teknologi. • For mer informasjon om retningslinjer for kvalitet og piksel for Dell-skjermen, se Dells støtteside: www.dell.com/pixelguidelines. Problemer med lysstyrke Bildet er for mørkt eller for lyst • Nullstill skjermen til fabrikkinnstillingene. • Juster kontrollene for lysstyrke og kontrast ved å gå til Display (Skjerm)-menyen.
Feil farge Bildefargen er ikke god • Endre innstillingene for Preset Modes (Forhåndsinnstilte moduser) i Game (Spill)OSD-menyen, avhengig av applikasjonen. • Juster verdier for Gain (Gevinst)/Offset (Forskyvning)/Hue (Fargetone)/Saturation (Fargemetning) ved å gå til Custom Color (Egendefinert farge) i Game (Spill)-OSDmenyen. • Start den innebygde diagnosefunksjonen.
Problemer knyttet med Universal Serial Bus (USB) Spesifikke symptomer Hva du opplever Mulige løsninger USBgrensesnittet fungerer ikke USB-enheter fungerer ikke • Bekreft at skjermen er slått på. • Koble til oppstrømskabelen til datamaskinen på nytt. • Koble til USB-enhetene på nytt (nedstrømskontakt). • Slå skjermen av og deretter på igjen. • Start datamaskinen på nytt. • Noen USB-enheter, f.eks. en ekstern bærbar harddisk, krever høyere elektrisk spenning; koble enheten direkte til datamaskinen.
Vedlegg ADVARSEL: Sikkerhetsinstruksjoner ADVARSEL: Hvis andre kontroller, justeringer eller prosedyrer enn de som nevnes i denne dokumentasjonen brukes, kan dette føre til eksponering for støt, elektriske farer og/eller mekaniske farer. Hvis du ønsker å ha mer informasjon om sikkerhetsinstruksjoner, se Sikkerhet-, miljø- og forskriftsinformasjon. FCC-merknader (kun USA) og annen forskriftsinformasjon For FCC-merknader og annen forskriftsinformasjon, se nettstedet for regelverksoverholdelse på www.dell.