Alienware AW3418DW/AW3418HW 顯示器 使用指南 機型:AW3418DW/AW3418HW 規格型號:AW3418DWb/AW3418HWb
注意、小心與警告訊息 注意: 「注意」意指重要資訊的注意事項,可幫助您更妥善使用電腦。 小心: 「小心」意指未遵循指示可能導致硬體損壞或資料遺失。 警告: 「警告」意指可能會造成財產損害、人體傷害或導致死亡。 Copyright © 2017-2018 Dell Inc. 版權所有。本產品受美國及國際版權及智慧財產法保護。Dell™ 及 Dell 標誌為 Dell Inc. 在美國及 / 或其它司法管轄區的商標。本文提及的其它所有標誌及名稱可能 為個別公司的商標。 2018 - 11 Rev.
目次 關於您的顯示器 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 包裝內容 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 產品功能特色 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 認識各部位與控制裝置 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 前視圖 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9 背視圖 . . . . . . . . . . . . . . . . . . . . . . . . . . . .
連接電腦 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 移除顯示器支架. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 VESA 壁掛式組件 (選購). . . . . . . . . . . . . . . . . . . . . . . . . . . .32 操作顯示器 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 開啟顯示器電源. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33 使用前面板控制按鈕 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33 前面板按鈕 . . . . .
通用序列匯流排 (USB) 特定問題 . . . . . . . . . . . . . . . . . . . . . . . 62 附錄 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63 FCC 聲明 (僅針對美國)與其它法規資訊 . . . . . . . . . . . . . . . 63 RoHS 聲明 (僅針對台灣). . . . . . . . . . . . . . . . . . . . . . . . . . . . 63 與 Dell 聯絡 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
關於您的顯示器 包裝內容 您的顯示器包裝中包含以下元件。請確認您收到所有元件,如缺少任何物品請 與 Dell 聯絡。如需詳細資訊,請參閱與 Dell 聯絡。 注意:某些物件可能為選購配件,因此不會隨您的顯示器而提供。某些功能 或媒體在某些國家中可能無法使用。 顯示器 可調式支架 I/O 外蓋 6 | 關於您的顯示器
電源線 (依國家而 不同) DisplayPort 連接線 Mini-DisplayPort 轉 DisplayPort 連接線 USB 3.
產品功能特色 Alienware AW3418DW/AW3418HW 顯示器配備主動式矩陣、薄膜式電晶 體 (TFT) 的液晶顯示器 (LCD) 並使用 LED 背光源。此顯示器的功能特色包括: • AW3418DW:86.72 cm (34.14 英吋)可視區域 (對角測量)。解析 度:透過 DisplayPort 和 HDMI,最高可達 3440 x 1440,支援全螢幕 顯示功能或較低解析度,以及極高的 100 Hz 重新整理速率 (超頻則為 120 Hz)。 • AW3418HW:86.70 cm (34.
認識各部位與控制裝置 前視圖 標籤 1 說明 連接線整理槽 (在支架正面) 2 功能按鈕 (如需詳細資訊,請參閱操作顯示器) 3 電源開啟 / 關閉按鈕 (含 LED 指示燈) 關於您的顯示器 | 9
背視圖 含顯示器支架的背視圖 標籤 1 說明 使用 VESA 安裝孔 (100 mm x 採用 VESA 相容的壁掛安裝套件安裝 100 mm - 於安裝的外蓋後方) 顯示器 (100 mm x 100 mm)。 2 燈光基座 可調式支架安裝於顯示器時,基座會 供應支架燈光所需的電源。 3 法規標籤 列出通過的法規。 4 支架移除按鈕 可從顯示器鬆開支架。 5 條碼序號標籤 若要聯絡 Dell 以取得技術支援,請參 考標籤上的資訊。 6 連接線整理槽 可將連接線穿過此整理槽以整理連 接線。 (在支架左側和右側) 10 | 關於您的顯示器
後視圖和底視圖 無顯示器支架的後視圖和底視圖 標籤 1 說明 使用 電源連接器 連接電源線 (顯示器隨附)。 2 線路輸出連接埠 連接喇叭。 3 DisplayPort 使用 DisplayPort-DisplayPort 或 MiniDisplayPort-DisplayPort 連接線 (顯示器隨 附)連接電腦。 4 HDMI 連接埠 使用 HDMI 連接線連接電腦。 5 USB 上載埠 將 USB 連接線 (顯示器隨附)連接到此連接 埠和電腦,以便啟用顯示器的 USB 連接埠。 注意:此連接埠不支援耳機。 6、9 USB 3.
10 下照燈 顯示器安裝完畢時,點選觸控感測器即可開 啟或關閉下照燈。 注意:原廠設定值為開啟,如果連接電源線,下照燈將啟動。若要 變更原廠設定值,請參閱 AlienFX Lighting (AlienFX 燈光)。 注意:Spectrum (頻譜)功能為開啟時,下照燈將關閉。 下照燈狀態 12 | 顯示器狀態 Spectrum (頻譜) 為關閉時 Spectrum (頻譜) 為開啟時 開啟 啟用 停用 無訊號 啟用 停用 待機 啟用 停用 關於您的顯示器
顯示器規格 平面面板規格 機型 AW3418DW 螢幕類型 主動式矩陣 - TFT LCD 面板技術 橫向電場效應類型 21:9 縱橫比 AW3418HW 可視影像 對角 867.2 mm (34.14 英吋) 867.0 mm (34.13 英吋) 寬度 (有效顯示區域) 799.80 mm (31.49 英吋) 799.80 mm (31.49 英吋) 高度 (有效顯示區域) 334.80 mm (13.18 英吋) 334.80 mm (13.18 英吋) 267,773.04 mm2 267771.43 mm2 全部區域 (415.01 平方英吋) (415.01 平方英吋) 0.2325 mm x 0.2325 mm 0.31 mm x 0.31 mm 像素點距 每英吋像素 (PPI) 109 視角 178° (垂直)典型 81.
連接埠和連接器 • 1 個 1.2 版的 DisplayPort 連接埠 • 1 個 1.4 版的 HDMI 連接埠 • 1 個 USB 3.0 上載埠 (後方) • 2 個 USB 3.0 下載埠 (後方) • 2 個 USB 3.0 下載埠 (底部) • 1 個耳機連接埠 (底部) • 1 個音源線輸出連接埠 (後方) 邊緣寬度 (顯示器邊 緣至有效顯示區域) 10.45 mm (頂部) 7.9 mm (頂部) 9.77 mm (左側 / 右側) 7.02 mm (左側 / 右側) 18.43 mm (底部) 25.
預設顯示模式 HDMI 顯示模式 (AW3418DW) 顯示模式 IBM VGA、640 x 480p 水平更新率 垂直更新率 (kHz) (Hz) 31.5 像素時脈 同步極性 (MHz) (水平 / 垂直) 60 25.2 -/- VESA、720 x 480p 29.83 60 26.25 +/- VESA、720 x 576p 29.55 50 26 +/- VESA、800 x 600p 37.88 60 40 +/+ VESA、1024 x 768p 48.36 60 65 -/- HDTV、1280 x 720p 37.5 50 74.25 +/+ HDTV、1280 x 720p 45 60 74.25 +/+ HDTV、1920 x 1080p 56.25 50 148.5 -/+ HDTV、1920 x 1080p 67.5 60 148.5 +/+ 3440 x 1440@50Hz 73.7 50 265.
DP 顯示模式 (AW3418DW) 顯示模式 水平更新率 垂直更新率 (kHz) (Hz) 像素時脈 同步極性 (MHz) (水平 / 垂直) VESA, 640 x 480 31.5 60 25.2 -/- VESA, 800 x 600 37.88 60 40 +/+ VESA, 1024 x 768 48.36 60 65 -/- 3440 x 1440@60Hz 88.8 60 319.75 +/- 3440 x 1440@50Hz 73.7 50 265.25 +/- 3440 x 1440@85Hz 127.4 85 458.5 +/- 3440 x 1440@100Hz 151 100 531.52 +/- 3440 x 1440@105Hz 159 105 559.57 +/- 3440 x 1440@110Hz 166.9 110 587.38 +/- 3440 x 1440@115Hz 172.5 115 607.
電氣規格 機型 AW3418DW AW3418HW 影像輸入訊號 • HDMI 1.4,每條差動線為 600 mV,每對差動線輸入 阻抗為 100 ohm • DisplayPort 1.2,每條差動線為 600 mV,每對差動 線輸入阻抗為 100 ohm AC 輸入電壓 / 頻率 / 電壓 100 VAC 至 240 電流 VAC / 50 Hz 或 60 Hz + 3 Hz / 1.8 A (典型) 浪湧電流 電壓 100 VAC 至 240 VAC / 50 Hz 或 60 Hz + 3 Hz / 1.
121.37 mm (4.78 英寸) 深 95.15 mm (3.74 英寸) 支架尺寸 高 (延伸時) 448.95 mm (17.68 英吋) 高 (收縮時) 442.44 mm (17.42 英吋) 寬 559.40 mm (22.02 英吋) 深 319.09 mm (12.56 英吋) 重量 19.28 公斤 (42.49 磅) 18.89 公斤 (41.64 磅) 含包裝重量 含支架組件與連接線的重量 12.24 公斤 (26.98 磅) 11.81 公斤 (26.03 磅) 不含支架組件的重量 (壁掛安裝或 VESA 安裝 方式 - 沒有連接線) 7.27 公斤 (16.02 磅) 6.91 公斤 (15.23 磅) 支架組件的重量 4.59 公斤 (10.12 磅) 4.52 公斤 (9.
• 375.3 BTU/ 小時 (最大) • 324.1 BTU/ 小時 (最大) 散熱 • 204.7 BTU/ 小時 (典型) • 170.6 BTU/ 小時 (典型) 電源管理模式 若您的電腦上已安裝符合 VESA DPM™ 規格的顯示卡或軟體,此顯示器便可於 未使用時自動降低其耗電量。意指省電模式 *。若電腦偵測到來自鍵盤、滑鼠或 其它輸入裝置的輸入訊號,顯示器便會自動恢復正常運作。下列表格中列出此 自動省電功能的耗電量與訊號指示。 AW3418DW VESA 模式 正常運作 水平同步 垂直同步 使用中 使用中 視訊 使用中 電源指示燈 耗電量 110 W (最大) ** 藍色 60 W (典型) 啟動關閉 模式 未啟動 未啟動 空白 白色 (閃爍) 低於 0.5 W 關閉 - - - 關閉 低於 0.3 W AW3418HW VESA 模式 正常運作 水平同步 垂直同步 使用中 使用中 視訊 使用中 電源指示燈 藍色 耗電量 95 W (最大) ** 50 W (典型) 啟動關閉 模式 未啟動 未啟動 空白 白色 (閃爍) 低於 0.
針腳定義 DisplayPort 連接器 針腳編號 20 | 20 針腳訊號連接線的顯示器端 1 ML0(p) 2 接地 3 ML0(n) 4 ML1(p) 5 接地 6 ML1(n) 7 ML2(p) 8 接地 9 ML2(n) 10 ML3(p) 11 接地 12 ML3(n) 13 接地 14 接地 15 AUX(p) 16 接地 17 AUX(n) 18 接地 19 Re-PWR 20 +3.
HDMI 連接器 針腳編號 19 針腳訊號連接線的顯示器端 1 TMDS 資料 2+ 2 TMDS 資料 2 遮蔽 3 TMDS 資料 2- 4 TMDS 資料 1+ 5 TMDS 資料 1 遮蔽 6 TMDS 資料 1- 7 TMDS 資料 0+ 8 TMDS 資料 0 遮蔽 9 TMDS 資料 0- 10 TMDS 時脈 + 11 TMDS 時脈遮蔽 12 TMDS 時脈 - 13 CEC 14 保留 (裝置上的 N.C.
通用序列匯流排 (USB) 介面 此部分提供有關您顯示器上可用的 USB 連接埠資訊。 注意:本顯示器相容超高速 USB 3.0。 傳輸速度 資料速度 耗電量 * 超高速 5 Gbps 4.5 W (每個連接埠最高) 高速 480 Mbps 4.5 W (每個連接埠最高) 全速 12 Mbps 4.
USB 下載連接器 9 針腳連接器端 針腳編號 1 VCC 2 D- 3 D+ 4 接地 5 SSRX- 6 SSRX+ 7 接地 8 SSTX- 9 SSTX+ USB 連接埠 • 1 個上載埠 - 後方 • 2 個下載埠 - 後方 • 2 個下載埠 - 底部 • 充電連接埠 – 帶有 援快速電流充電功能。 電池圖示的連接埠;裝置為 BC1.2 規格時,支 注意:USB 3.0 功能需要一台 USB 3.
液晶顯示器品質與像素政策 在液晶顯示器生產過程中,某個或者多個像素有時會保持不變狀態,這些像素 很難發現,而且不會影響顯示器品質或者功能。有關 Dell 顯示器品質與像素政 策的詳情,如需更多資訊,請參閱 www.dell.
設定顯示器 安裝支架 注意:從工廠出貨時並未安裝支架。 注意:下列說明適用於安裝顯示器隨附的支架。如果安裝從其它任何來源購 買的支架,請按照連同支架提供的安裝說明進行。 小心:這些步驟對於保護曲面螢幕相當重要。請按照下列說明完成安裝。 安裝顯示器支架: 1. 打開包裝箱,取出包裝頂端的泡棉軟墊。 2.
3. 握緊顯示器的兩側,輕輕抬起顯示器。 4.
5. 將顯示器放在泡棉上,螢幕朝下。 6.
7. 將必要連接線連接到顯示器,如圖所示,並將連接線穿過可調式支架的連 接線整理槽。 a. 電源線 b. DisplayPort 連接線或 Mini-DisplayPort 轉 DisplayPort 連接線 c. HDMI 連接線 (選購,不含連接線) d. USB 上載連接線 e. USB 下載連接線 (選購,不含連接線) 注意:將連接線佈設整齊,以便在蓋上 I/O 外蓋後連接線能整齊收納。 警告:請勿將電源線插入牆面插座或開啟顯示器電源,除非說明指示已 告知。 8. 確定 I/O 外蓋上的扣件對準顯示器後方的插槽 1 和插槽 2。 9.
10. 滑動 I/O 外蓋,直到卡入定位。 注意:確定連接線不受阻礙,並穿過可調式支架的 I/O 外蓋和連接線整 理槽。 連接電腦 警告:在您開始執行此小節的任何程序之前,請先仔細閱讀並遵守安全資 訊。 注意:請勿將全部的連接線同時連接到電腦。 將您的顯示器連接至電腦: 1. 將已連接的 DisplayPort (或 Mini-DisplayPort 轉 DisplayPort)或 HDMI 連接線的另一端連接到電腦。 2. 將 USB 3.0 上載埠 (隨附連接線)連接至您電腦上適當的 USB 3.0 連接 埠。(細節請參閱後視圖和底視圖) 3. 將 USB 3.0 周邊設備連接至顯示器的 USB 3.
4. 將電腦與顯示器的電源線插入附近的電源插座。 5. 打開顯示器與電腦。 若您的顯示器有顯示影像,便表示安裝完成。若顯示器沒有顯示影像,請 參閱通用序列匯流排 (USB) 特定問題。 注意:圖示僅用於說明。電腦的外觀可能會有所不同。 移除顯示器支架 注意:為避免移除支架時刮傷 LCD,請確認將顯示器放置於乾淨柔軟的表 面上。 注意:下列說明適用於安裝顯示器隨附的支架。如果安裝從其它任何來源購 買的支架,請按照連同支架提供的安裝說明進行。 移除支架: 1. 關閉顯示器。 2. 從電腦上拔除連接線。 3. 將顯示器放在軟布或軟墊上。 4.
5. 拔除顯示器的連接線,並將連接線穿過可調式支架的連接線整理槽。 6. 按住支架移除按鈕。 7.
VESA 壁掛式組件 (選購) (螺絲尺寸:M4 x 10 mm)。 請參考 VESA 相容壁掛安裝套件隨附的說明。 1. 將螢幕面板置於穩固平坦鋪有軟布或墊子的表面上。 2. 取下顯示器支架。(請參閱移除顯示器支架。) 3. 使用十字螺絲起子取下四顆鎖住塑膠外蓋的螺絲。 4. 將壁掛安裝套件中的安裝托架連接至顯示器。 5. 將顯示器安裝於牆面。如需詳細資訊,請參閱壁掛安裝套件隨附的說明 文件。 注意:僅限使用符合 UL 列名的壁掛式托架,最小重量或負載能力為 29.1 公斤 (AW3418DW)/27.
操作顯示器 開啟顯示器電源 按下電源按鈕以開啟顯示器。 使用前面板控制按鈕 使用顯示器前方的控制按鈕調整設定。 下表說明前面板按鈕的功用: 前面板按鈕 1 說明 使用此按鈕可從預設之色彩模式清單中選擇色彩 模式。 快捷鍵 /Preset Modes (預設 模式) 2 使用此按鈕,啟動 Overclock Refresh Rate (超頻重新整理速率)功能表。 快捷鍵 /Overclock Refresh Rate (超頻重新整理 速率) 操作顯示器 | 33
3 使用此按鈕,啟動 Dark Stabilizer (暗處穩定 器)功能表。 快捷鍵 / Dark Stabilizer (暗處穩定器) 4 快捷鍵 / Brightness/ Contrast (亮度 / 對比) 5 使用此按鈕可直接啟動 Brightness/Contrast (亮度 / 對比)功能表。 使用功能表按鈕啟動畫面顯示項目 (OSD)。請參 閱存取功能表系統。 功能表 6 使用此按鈕結束 OSD 主功能表。 離開 前面板按鈕 使用顯示器前方的按鈕以調整影像設定。 前面板按鈕 1 說明 使用上按鈕以調整 (增加範圍) OSD 功能表中的項目。 上 2 使用下按鈕以調整 (減少範圍) OSD 功能表中的項目。 下 3 使用選擇按鈕以確認選擇。 選擇 4 使用返回按鈕以返回上一個功能表。 返回 34 | 操作顯示器
使用畫面顯示項目 (OSD) 功能表 存取功能表系統 注意:若您變更設定並進入其它功能表,或離開 OSD 功能表,顯示器會 自動儲存這些變更。若您變更設定並等待 OSD 功能表消失,變更也會被 儲存。 1. 按下 按鈕以啟動 OSD 功能表並顯示主功能表。 2. 按下 與 按鈕即可於選項間移動。在圖示間移動時,選項名稱會反 白顯示。所有可調整項目的完整清單請參閱下表。 3. 按一下 按鈕可啟動反白顯示的選項。 4. 按下 與 5. 按下 進入子功能表,然後使用方向鍵依功能表的指示進行所需變更。 6.
圖示 功能表與 子功能表 說明 Game (遊戲) 使用此功能表個人化您的視覺遊戲體驗。 Preset Modes 可讓您從預設色彩模式清單中選擇色彩模式。 (預設模式) • Standard (標準):載入顯示器的預設色彩設定。此為預 設模式。 • FPS:載入最適合第一人稱射擊遊戲的色彩設定。 • RTS:載入最適合即時戰略遊戲的色彩設定。 • RPG:載入最適合角色扮演遊戲的色彩設定。 • Game 1 (遊戲 1) /Game 2 (遊戲 2) /Game 3 (遊戲 3):可任您自訂色彩調整,符合您的遊戲需求。 36 | 操作顯示器
Preset Modes • ComfortView:降低螢幕發出的藍光量,讓眼睛在觀看時 (預設模式) 更舒適。 警告:顯示器發出的藍光可能會造成長期影響使人 體受到傷害,包括數位視覺疲勞、眼睛疲勞與眼睛 傷害。長時間使用顯示器也可能造成例如頸部、手 臂、背部與肩部等身體疼痛。 若要降低由於長時間使用顯示器所造成的眼睛疲勞和 頸部 / 手臂 / 背部 / 肩部疼痛,建議您: 1. 將螢幕放置於距離眼睛 20 至 28 英吋 (50 至 70 公 分)之處。 2. 長時間觀看顯示器後,經常眨眼或用水保持眼睛濕潤。 3. 每觀看兩小時固定休息 20 分鐘。 4. 在休息時不觀看螢幕,並且注視至少距離 20 英呎遠的 物體至少 20 秒。 5.
Game Enhance 此功能提供三種可用功能,能強化您的遊戲體驗。 Mode (遊戲強 化模式) • Off (關閉) 選擇可停用在 Game Enhance Mode (遊戲強化模式)的下 功能。 • Timer (計時器) 可讓您停用或啟用在畫面左上角的計時器。計時器會顯示遊 戲開始後已遊玩的時間。從遊戲時間間隔清單選擇選項,即 可測量目標遊戲速率。 • Frame Rate (畫面播放速率) 選擇 On (開啟),可在您的遊玩期間顯示目前的每秒畫面播 放速率。速率愈高,表示動作愈順暢。 • Display Alignment (顯示對齊) 啟動功能,確認影片內容在多部顯示器上正確對齊。 Overclock (超頻) 可讓您以高於面板規格指定的重新整理速率運作顯示器。 注意:只有在使用 DP (DisplayPort) 輸入時,才能使用此 功能。 注意:超頻可能造成螢幕閃爍。為了減少這種效應,請嘗試 在 Overclock Refresh Rate (超頻重新整理速率)功能表中 設定較低的重新整理速率。 38 | 操作顯示器
Overclock 此功能可提高顯示器的重新整理速率。 Refresh Rate 或 可用來調整頻率,每調整一次增減 5 Hz,範圍在 (超頻重新整理 105 至 120 Hz (AW3418DW 適用)或 150 至 160 Hz 速率) (AW3418HW 適用)之間。 您指定重新整理速率後,將出現下列訊息引導您完成程序: 注意:只有在使用 Overclock (超頻)時,才能使用此功能。 注意:超頻可能造成螢幕閃爍。為了減少這種效應,請嘗試 設定較低的重新整理速率。 Response Time 可讓您將 Response Time (反應時間)設定為 Normal (正 (反應時間) 常)、Fast (快速)或 Super Fast (超級快速)。 Dark Stabilizer 此功能可提升遊戲暗處場景的可見度。值愈高 (位於 0 至 3 (暗處穩定器) 之間)表示顯示影像的暗處可見度愈好。 Reset Game (重設遊戲) 選擇此選項可還原預設遊戲設定。 操作顯示器 | 39
Brightness/ 使用此功能表可啟動 Brightness/Contrast (亮度 / 對比) Contrast 調整。 (亮度 / 對比) Brightness (亮度) Contrast (對比) Brightness (亮度)功能可調整背光的亮度。 按下 按鈕可增加亮度,按下 小值 0 / 最大值 100)。 按鈕則可減少亮度 (最 請先調整 Brightness (亮度),如需進階調整,接著再調整 Contrast (對比)。 按下 按鈕可增加對比,按下 小值 0 / 最大值 100)。 按鈕則可減少對比 (最 Contrast (對比)功能可用以調整顯示器畫面上的明暗度。 Input Source (輸入來源) HDMI DP 40 | 操作顯示器 使用 Input Source (輸入來源)功能表可選擇連接顯示器的 不同視訊訊號。 使用 HDMI 連接器時,請選擇 HDMI 輸入。 使用 DisplayPort (DP) 連接器時,請選擇 DP 輸入。
AlienFX Lighting (AlienFX 燈光) 使用此功能表調整 Alienware 標誌燈光、顯示器背後和支架的 Triad 燈光、顯示器底部的下照燈,以及電源按鈕。 進行任何調整前,請從子功能表選擇任一個或全部 4 個區域。 下圖顯示燈光區域。 操作顯示器 | 41
All Zones 若要指定所選區域的 LED 燈光顏色,請選擇 On (開啟), (全部區域) 並按下 按鈕反白顯示 Custom Color (自訂色彩)選項。 Zone 1: Back (區域 1: 背面) Zone 2: Stand (區域 2: 支架) Zone 3: Downlights (區域 3: 下照燈) Zone 4: Power Button (區域 4:電源 按鈕) 然後使用 和 按鈕,從 20 種可用顏色清單中選擇 其一。 42 | 操作顯示器
下表列出 20 個 LED 顏色的顏色編號和 RGB 代碼。 編號 R G B 1 0 0 0 2 100 0 240 3 144 0 240 4 240 0 240 5 240 0 176 6 240 0 112 7 240 0 0 8 240 80 0 9 240 128 0 10 240 224 0 11 120 240 0 12 160 240 0 13 100 245 35 14 0 240 0 15 0 240 85 16 70 240 145 17 0 240 240 18 0 160 240 19 0 96 240 20 0 0 240 若要關閉 AlienFX 燈光,請選擇 Off (關閉)。 注意:只有在停用 Spectrum (頻譜)時,才能使用這些 功能。 操作顯示器 | 43
Spectrum (頻譜) 您選擇 On (開啟)時,4 個區域的 AlienFX 燈光會亮起, 並依照以下頻譜順序變更顏色:紅色、橘色、黃色、綠色、 藍色、青色與紫色。 注意:該功能為 On (開啟)時,以上功能將停用。 Reset AlienFX 選擇此選項可還原預設燈光設定。 Lighting(重設 AlienFX 燈光) Audio (音訊) Volume (音量) Reset Audio (重設音訊) 44 | 操作顯示器 可讓您設定耳機輸出的音量。 使用 或 可調整 0 至 100 之間的音量。 選擇此選項可還原預設的音訊設定。
Menu (功能表) 選擇此選項可調整 OSD 設定,如 OSD 語言、功能表停留於 螢幕上的時間等。 Language (語言) 設定 OSD 顯示螢幕上的八種語言之一 (英文、西班牙文、 法文、德文、巴西葡萄牙文、俄文、簡體中文或日文)。 Transparency 選擇此選項可按下 和 按鈕以變更功能表透明度 (透明度) (最小值 0 / 最大值 100)。 Timer (計時器) 設定自最後一次您按下按鈕後 OSD 保持時間的長度。 使用 或 60 秒)。 可以 1 秒為增減單位調整滑動桿 (5 至 Reset Menu 重設所有 OSD 設定為原廠預設值。 (重設功能表) Personalize (個人化) 操作顯示器 | 45
Shortcut Key 1 (快捷鍵 1) Shortcut Key 2 (快捷鍵 2) Shortcut Key 3 (快捷鍵 3) Shortcut Key 4 (快捷鍵 4) Reset Personalization (重設個人化) 可讓您選擇 Preset Modes (預設模式)、Overclock Refresh Rate (超頻重新整理速率)、Dark Stabilizer (暗處穩定 器)、Brightness/Contrast (亮度 / 對比)、Game Enhance Mode (遊戲強化模式)、Input Source (輸入來 源)或 Volume (音量),並設定為快捷鍵。 將快捷鍵還原至原廠預設值。 Others (其它) Display Info 顯示本顯示器的所有設定值。 (顯示資訊) Power Saving 預設設定為 On (開啟),可讓顯示器在系統睡眠時進入睡眠 (省電) 模式。設定 Off (關閉)可防止顯示器進入深度睡眠且無法 喚醒。 注意:按下顯示器前面版的任何按鈕 (除了電源按鈕)也可 以將進入深度睡眠的顯示器喚醒。 Factory Reset 重
OSD 警告訊息 當顯示器進入 Power Saving (省電)模式時,將會出現下列訊息: 請參閱疑難排解以取得更多資訊。 設定最大解析度 為顯示器設定最大解析度: 在 Windows 7、Windows 8 和 Windows 8.1 系統中: 1. 僅適用於 Windows 8 和 Windows 8.1,選取桌面動態磚以切換至傳統 桌面。 2. 在桌面上按一下右鍵,然後選擇螢幕解析度。 3. 按一下螢幕解析度的下拉式清單,選取 3440 x 1440 (AW3418DW 適 用)或 2560 x 1080 (AW3418HW 適用)。 4. 按一下確定。 在 Windows 10 系統中: 1. 在桌面上按一下右鍵,然後選擇顯示設定。 2. 按一下進階顯示設定。 3. 按一下解析度的下拉式清單,選取 3440 x 1440 (AW3418DW 適用)或 2560 x 1080 (AW3418HW 適用)。 4.
使用傾斜、旋轉和垂直展開功能 注意:下列說明適用於安裝顯示器隨附的支架。如果安裝從其它任何來源購 買的支架,請按照連同支架提供的安裝說明進行。 傾斜、旋轉 支架連接到顯示器上時,您可以傾斜與旋轉顯示器,以找出最舒適的觀賞角度。 注意:從工廠出貨時並未安裝支架。 垂直展開 注意:支架的垂直展開高度最大為 130 mm。下圖說明如何垂直展開支架。 48 | 操作顯示器
使用 AlienwareFX 應用程式 AlienwareFX 應用程式可供存取 Alienware gaming monitor control center (Alienware 遊戲顯示器控制中心)。使用此應用程式可控制 LED 燈光顏色和 Alienware 遊戲顯示器的運作方式。 注意:可從下列網址下載 AlienFX 應用程式: http://www.dell.com/support/home/us/en/04/products/。 注意:如果您使用 Alienware Gaming 桌上型或筆記型電腦,請使用 AWCC (Alienware Command Center) 控制燈光。 先決條件 在非 Alienware 系統上使用 AlienFX 應用程式前: • 確定網際網路連線正常運作。 • 將 Alienware 顯示器的 USB 3.0 上載埠 (隨附連接線)連接至您電腦上可 用的 USB 3.
進入 AlienFX 應用程式 如果具備使用 AlienFX 應用程式的所有先決條件,按兩下桌面上的捷徑圖示 將進入 Alienware gaming monitor control center (Alienware 遊戲顯示器 控制中心)。 下表提供該應用程式的概覽。 編號 A 功能 顯示器縮圖 說明 顯示透過 USB 上載連接線連接到電腦的所有 Alienware 遊 戲顯示器。先從縮圖中選取顯示器,再進行調整。 如果只有一台顯示器連接到系統,將顯示一個顯示器縮 圖,而且您可以略過選取顯示器的動作。 B 區域選取 區域都有號碼。若要選取一個區域,請按一下影像中的區 域,或使用核取方塊選取區域。 若要選取全部的區域,請勾選 All (全部)核取方塊。 C 燈光控制 這些控制項可指定顯示器的燈光效果。 細節請參閱 「設定燈光效果」。 D 關於 選取可檢視目前的版本號碼。 E 最小化 按一下可將應用程式視窗最小化。 F 關閉 按一下可離開應用程式視窗。 注意:當您結束此應用程式時,將不會儲存您所做的變更。 50 | 使用 AlienwareFX 應用程式
設定燈光效果 您可以按一下下列任何一個選項,調整所選區域的燈光效果: 圖示 燈光效果 • 基本色彩 • 動畫預設 注意:在下列情況下,您可能無法存取您所做的燈光效果設定: • 結束此應用程式 • 中斷顯示器和電腦的 USB 上載連接線的連接 基本色彩 此選項能夠使 LED 燈光恆亮一種顏色。 基本色彩 說明 若要套用此效果: 1. 從調色盤 (或預設色彩的清單)中選取偏好 的色彩。選取的色彩及其 RGB 色彩代碼隨即 顯示。 2.
動畫預設 您可以從預設燈光控制面板選擇 Morphing (變形)、Pulsing (脈衝)或 Spectrum (頻譜)。 Morphing (變形) 說明 此效果是透過流暢的轉換方式來變換燈光色彩。 若要套用此效果: 1. 選取 Color 1 (色彩 1)按鈕設定開始的燈光 色彩。 2. 從調色盤 (或預設色彩的清單)中選取偏好 的色彩。選取的色彩及其 RGB 色彩代碼隨即 顯示。 3. 選取 Color 2 (色彩 2)按鈕設定結束的燈光 色彩。 4. 重複步驟 2。 5. 選取 Apply (套用)儲存變更。 注意:如需預設色彩的詳細資料,請參閱自訂預設 色彩。 Pulsing (脈衝) 說明 此效果會使燈光快速閃爍。 若要套用此效果: 1. 從調色盤 (或預設色彩的清單)中選取偏好 的色彩。選取的色彩及其 RGB 色彩代碼隨即 顯示。 2.
Spectrum (頻譜) 說明 此效果會使燈光按照頻譜的順序變化。紅色、橘色、 黃色、綠色、藍色、青色與紫色。 若要套用此效果: 1. 從下拉式清單中選取 on (開啟)。 2.
建立一組預設色彩 您最多可建立 10 組預設色彩,以便您快速存取偏好的色彩。 若要這麼做: 1. 從清單中按一下新的色票 。 2. 從調色盤中選取偏好的色彩。選取的色彩及其 RGB 色彩代碼隨即顯示。 3. 若要將其他色彩新增到清單中,請重複步驟 1 和步驟 2。 注意:除了預設的黑色之外, ,您總共可新增 9 種色彩。 4. 當您選好色彩清單時,按一下 Save as new preset (另存為新預設)。 5. 在 Preset Name (預設名稱)視窗中,使用鍵盤將該組預設色彩命名。 6. 選取 OK (確定)儲存該組自訂預設色彩。 7.
變更預設色彩 若要變更預設色彩: 1. 按一下 開啟自訂色彩組的清單。 2. 選取要變更色彩的那一組。 3. 按一下所需的色票 (既有色彩)反白顯示該色票。 4. 從調色盤中選取偏好的色彩。選取的色彩及其 RGB 色彩代碼隨即顯示。 5.
刪除預設色彩 1. 按一下 開啟自訂色彩組的清單。 2. 選取要移除色彩的那一組。 3. 以滑鼠右鍵按一下所需的色票 (既有色彩)顯示 「Delete Color」(刪除 色彩)子功能表,並選取該選項儲存變更。 4.
刪除一組預設色彩 若要刪除您建立的一組自訂預設色彩: 1. 按一下 開啟清單。 2. 從開啟的清單中,選取要刪除的那一組。 3. 按一下 。 4.
疑難排解 警告:在您開始執行此小節的任何程序之前,請先仔細閱讀並遵守安全資 訊。 自我測試 您的顯示器具備可讓您檢查顯示器功能是否正常的自我測試功能。若您的顯示 器與電腦已正確連接,但顯示器螢幕依然不亮,請您依照以下步驟執行顯示器 自我測試: 1. 關閉電腦與顯示器。 2. 從電腦後方拔除視訊連接線。為確保正確的自我測試操作,請將數位連接 線自電腦後方拔除。 3. 啟動顯示器。 注意:若顯示器正常運作但無法感應到影像訊號,螢幕上便會出現對話方塊 (黑底)。在自我測試模式中時,LED 電源指示燈會閃爍白色。 注意:若視訊連接線連結中斷或損壞,在正常的系統運作期間亦將顯示此 方塊。 4.
內建診斷工具 您的顯示器配備了內建診斷工具,可協助您判斷螢幕異常現象是顯示器或電腦 與視訊卡的問題。 注意:您只有在拔除視訊連接線並且在顯示器處於自我測試模式時,才可執 行內建診斷作業。 如欲執行內建診斷作業: 1. 請確定螢幕畫面是乾淨的 (螢幕表面沒有灰塵微粒)。 2. 從電腦或顯示器後方拔除視訊連接線。顯示器便會進入自我測試模式。 3. 按住按鈕 3,保持 5 秒鐘。1 秒後便會出現灰色畫面。 4. 請小心檢查畫面上的異常現象。 5. 再次按下按鈕 3。螢幕的色彩便會變成紅色。 6. 請檢查顯示畫面上的異常現象。 7.
常見問題 下表所列是有關於您可能遭遇常見的顯示器問題,與可能解決方法的一般資訊: 一般徵兆 問題說明 無視訊 / 電源 無影像 LED 指示燈熄滅 可能的解決方法 • 請確定連接顯示器與電腦的視訊連接線已正確連 接並固定。 • 請藉由使用其它電器設備以確認電源插座是否正 常運作。 • 請確定完全壓下電源按鈕。 • 請確定在 Input Source (輸入來源)功能表中選 擇正確的輸入來源。 無視訊 / 電源 無影像或沒有亮 • LED 指示燈亮起 度 • • • • 焦距模糊 透過 OSD 提高亮度與對比度設定。 執行顯示器自我測試功能檢查。 檢查視訊連接線接頭針腳是否有彎曲或斷裂。 執行內建診斷作業。 請確定在 Input Source (輸入來源)功能表中選 擇正確的輸入來源。 影像模糊、不清 • 去除視訊延長線。 楚或有重影 • 將顯示器重設為原廠設定值。 • 變更視訊解析度為正確的縱橫比。 視訊抖動 / 跳動 影像出現波紋或 • 將顯示器重設為原廠設定值。 細微移動 • 檢查環境因素。 • 將顯示器移至另一個房間再次進行測試。 像素遺失 LCD 螢幕出現 斑點 • 關閉電源,然後重
水平 / 垂直線條 螢幕上出現一條 • 將顯示器重設為原廠設定值。 或多條線段 • 執行顯示器自我測試功能檢查,並確定這些線條 是否也在自我測試模式中出現。 • 檢查視訊連接線接頭針腳是否有彎曲或斷裂。 • 執行內建診斷作業。 同步化問題 畫面雜亂或分割 • 將顯示器重設為原廠設定值。 • 執行顯示器自我測試功能檢查,確定自我測試模 式中是否也出現雜亂的畫面。 • 檢查視訊連接線接頭針腳是否有彎曲或斷裂。 • 在安全模式中重新啟動電腦。 安全相關問題 明顯冒煙或火花 • 請勿執行任何疑難排解步驟。 • 請立即聯絡 Dell。 週期性問題 顯示器故障出現 • 請確定顯示器與電腦的視訊連接線已正確連接並 與消失 固定。 • 將顯示器重設為原廠設定值。 • 執行顯示器自我測試功能檢查,並確定自我測試 模式中是否也出現週期性問題。 遺失色彩 圖片遺失色彩 • 執行顯示器自我測試功能檢查。 • 請確定顯示器與電腦的視訊連接線已正確連接並 固定。 • 檢查視訊連接線接頭針腳是否有彎曲或斷裂。 色彩錯誤 圖片色彩不佳 • 依應用程式變更 OSD 功能表中的 Game (遊 戲)功能表下的 Preset
無法使用前面板 OSD 未出現於螢 • 請關閉顯示器並拔除電源線,然後重新插上電源 上的按鈕調整顯 幕上 線並開啟顯示器電源。 示器 在按下使用者 無圖片時,LED • 請檢查訊號來源。請移動滑鼠或按下鍵盤上任一 控制時,無輸入 光源為藍色 鍵,以確定電腦不在省電模式中。 訊號 • 請檢查訊號連接線是否正確連接。如有需要請重 新插入訊號連接線。 • 將電腦或視訊放影機重新設定。 圖片未填滿整個 圖片無法填滿整 • 由於 DVD 有不同的視訊格式 (縱橫比),因此 螢幕 個螢幕的高度或 顯示器可以全螢幕播放影像。 寬度 • 執行內建診斷作業。 通用序列匯流排 (USB) 特定問題 特殊徵兆 問題說明 可能的解決方法 USB 介面無作用 USB 周邊設備無 • 確認您的顯示器電源為開啟。 • 將上載連接線重新連接至您的電腦。 作用 • 重新連接 USB 周邊設備 (下載連接器)。 • 關閉然後再度開啟顯示器。 • 重新啟動電腦。 • 部分 USB 裝置如外部可攜式硬碟機需要較高的 電流;直接將裝置連接至電腦系統。 超高速 USB 3.0 超高速 USB 3.0 • 確認您的電腦為 USB 3.
附錄 警告:安全資訊 警告:執行本說明文件中未指定的控制作業、調整方式或程序,可能會使您 暴露在觸電、電氣傷害和 / 或機械傷害的危險中。 關於安全指示的資訊,請參閱 「安全、環保與法規資訊 (SERI)」。 FCC 聲明 (僅針對美國)與其它法規資訊 關於 FCC 公告與其它法規資訊,請參閱 www.dell.com/regulatory_compliance 網站上產品符合哪些法規相關的資訊。 RoHS 聲明 (僅針對台灣) 單元 鉛 (Pb) 汞 (Hg) 限用物質及其化學符號 鎘 六價鉻 多溴聯苯 (Cd) (Cr+6) (PBB) 多溴二苯醚 (PBDE) — O O O O O 機箱 / 檔板 / 支架 — O O O O O 電路板組件 — O O O O O 顯示螢幕 — O O O O O 電線 / 連接器 — O O O O O 電源設備 — O O O O O 喇叭 / 麥克風 — O O O O O 配件 備考 1. “O” 係指該項限用物質之百分比含量未超出百分比含量基準值。 備考 2.