Deployment Guide

| 2.85G | 8.44M | 387.88G | 1.12G | 132 |
-------------------------------------------------------------------------------------------------
Monitoring an edge-to-edge flow through an egress port identified by a proxy ID
In a network set up as shown in Figure 6 on page 45, for a flow passing from Device B to Device A that
is egressing through EX_Port1, the source device (srcdev) is Device B′, the destination device (dstdev)
is Device A, and the egress port (egrport) is EX_Port1. (Traffic is running from left to right.)
The following example creates a flow that filters out frames passing from one edge fabric to another
edge fabric using a specific egress port on the backbone. The first two commands show the available
ports and the available Fibre Channel routers. The third command creates a Flow Monitor flow named
“e2e_dst_dcx” between device 01f001 and device 220200 egressing through port 219, and the last
command displays the results of the flow.
NOTE
The slash character (\) in the example indicates a break inserted because the output is too long to
display here as a single line.
DCX_Backbone128:admin> switchshow |grep Port
Index Slot Port Address Media Speed State Proto \
37 3 5 012500 id N16 Online FC EX-Port 10:00:00:05:33:ef:f1:1c \
47 3 15 012f00 id N8 Online FC F-Port 20:02:00:11:0d:51:00:00 \
219 10 27 01db00 id N16 Online FC EX-Port 10:00:00:05:33:ee:d0:a5 \
E-Port 50:00:51:e4:91:9e:0f:28 \
\
\ "Wasp_e2" (fabric id=50)(Trunk master)
\
\ "Gnat_e1" (fabric id=100)(Trunk master)
\ "fcr_xd_2_100"
DCX_Backbone128:admin> fcrproxydevshow
Proxy WWN Proxy Device Physical State
Created PID Exists PID
in Fabric in Fabric
--------------------------------------------------------------------------
50 10:00:00:05:1e:e8:e2:00 01f001 100 220200 Imported
100 20:00:00:11:0d:e4:18:00 01f001 50 030f00 Imported
100 20:02:00:11:0d:51:00:00 02f001 128 012f00 Imported
128 10:00:00:05:1e:e8:e2:00 02f001 100 220200 Imported
Total devices displayed: 4
DCX_Backbone128:admin> flow --create e2e_dst_dcx -feature monitor -egrport 219
-srcdev 01f001 -dstdev 220200
DCX_Backbone128:admin>flow --show
------------------------------------------------------------------------- \
Flow Name | Feature | SrcDev | DstDev \
------------------------------------------------------------------------- \
e2e_dst_dcx |mon+ |01f001 |220200 \
------------------------------------------------------------------------- \
\ --------------------------------------
\ |IngrPt|EgrPt|BiDir| LUN | FrameType|
\ --------------------------------------
\ |- |219 |no |- |- |
\ --------------------------------------
+ Denotes feature is currently activated for the flow
DCX_Backbone128:admin> flow --show e2e_dst_dcx -feature monitor
==========================================================================
Name : e2e_dst_dcx Features: mon(Active) noConfig: Off
Definition: EgrPort(219),SrcDev(0x01f001),DstDev(0x220200)
Flow Monitor (Activated):
Monitor time: | Mon Jun 17 14:59:58 UTC 2013 |
---------------------------------------------------------
------------------------------------------------------------------------------------------------
Monitoring an edge-to-edge flow through an egress port identified by a proxy ID
Flow Vision Administrators Guide 47
53-1003168-01