Administrator Guide

action={act=CopyToCpu, param0=1(0x1), param1=2(0x2), param2=0(0), param3=0(0)}
policer=
statistics={stat id 2 slice = 9 idx=0 entries=1}{Packets}
--More--
############## FP Entry for redirecting LACP traffic to CPU Port ############
EID 0x000002fd: gid=0xa,
slice=9, slice_idx=0x3, part =0 prio=0x2fd, flags=0x10202, Installed, Enabled
tcam: color_indep=0,
Stage
InPorts
DATA=0x0000000000000000000000000000000000000000000000000000222222222222
MASK=0x0000000000000000000000000000000000000000000000000000222222222223
DstMac
Offset: 88 Width: 48
DATA=0x00000180 c2000002
MASK=0x0000ffff ffffffff
action={act=DropPrecedence, param0=1(0x1), param1=0(0), param2=0(0), param3=0(0)}
action={act=Drop, param0=0(0), param1=0(0), param2=0(0), param3=0(0)}
action={act=CosQCpuNew, param0=3(0x3), param1=0(0), param2=0(0), param3=0(0)}
action={act=CopyToCpu, param0=1(0x1), param1=4(0x4), param2=0(0), param3=0(0)}
policer=
statistics={stat id 3 slice = 9 idx=1 entries=1}{Packets}
--More--
################# FP Entry for redirecting GVRP traffic to RSM ###########
EID 0x000002fc: gid=0xa,
slice=9, slice_idx=0x4, part =0 prio=0x2fc, flags=0x10202, Installed, Enabled
tcam: color_indep=0,
Stage
InPorts
DATA=0x0000000000000000000000000000000000000000000000000000222222222222
MASK=0x0000000000000000000000000000000000000000000000000000222222222223
DstMac
Offset: 88 Width: 48
DATA=0x00000180 c2000021
MASK=0x0000ffff ffffffff
action={act=DropPrecedence, param0=1(0x1), param1=0(0), param2=0(0), param3=0(0)}
action={act=Drop, param0=0(0), param1=0(0), param2=0(0), param3=0(0)}
action={act=CosQCpuNew, param0=4(0x4), param1=0(0), param2=0(0), param3=0(0)}
action={act=CopyToCpu, param0=1(0x1), param1=5(0x5), param2=0(0), param3=0(0)}
policer=
statistics={stat id 8 slice = 9 idx=2 entries=1}{Packets}
Viewing Per-Protocol CoPP Counters
To view per-protocol counters of rate-limited control-plane traffic, use the show control-traffic protocol [cp-switch |
[linecard {0-11} portset {0-0}] | [port-extender {0-255} stack-unit {0-7} portset {0-0}]
counters command, where:
• cp-switch displays counters for rate-limited traffic on the central switch (aggregated CoPP).
• linecard portset displays counters for rate-limited traffic on a specified switch line card and port set (distributed CoPP).
In the show output, Rx Counters displays the number of bytes of control-plane traffic received, on which protocol-based rate limiting is
applied. Tx Counters displays the number of bytes transmitted to a control-plane CPU after protocol-based rate limiting is applied. Drop
Counters displays the number of bytes of control-plane traffic that have been dropped as a result of protocol-based rate limiting.
Dell# show control-traffic protocol linecard 2 portset 0 counters |no-more
Protocol RxBytes TxBytes Drops
------- ------- ------- -----
STP 0 0 0
LLDP 8659 8659 0
PVST 0 0 0
LACP 0 0 0
GVRP 0 0 0
ARP RESP/ARP REQ 0 0 0
802.1x 0 0 0
FEFD 0 0 0
FRRP 0 0 0
ECFM 0 0 0
L2PT 0 0 0
ISIS 0 0 0
Control Plane Policing (CoPP)
229