Users Guide

• Display input and output statistics on the party bus, which carries inter-process communication traffic between CPUs.
show hardware party-bus {port { slot—id} | all} statistics
• Display the ingress and egress internal packet-drop counters, MAC drop counters, and FP packet drops for the line card on
a per port basis.
show hardware linecard slot—id drops unit unit-number port {port-number}
Use the command output to troubleshoot a line card and port-pipe unit that may experience internal drops.
• Display the input and output statistics for a stack-port interface.
show hardware linecard slot—id unit unit-number
• Display the counters in the field processors of a port-pipe unit on a line card.
show hardware linecard slot—id unit unit-number counters
• Display the details of the FP devices, and HiGig ports on a port-pipe unit on a line card.
show hardware linecard slot—id unit unit-number details
• Execute a specified bShell command from the CLI without going into the bShell.
show hardware linecard slot—id unit unit-number execute-shell-cmd {command}
• Display the Multicast IPMC replication table from the bShell.
show hardware unit unit-number ipmc-replication
• Display the internal statistics for each port-pipe (unit) on per port basis.
show hardware linecard slot—id unit unit-number port-stats [detail]
• Display the line-card internal registers for each port-pipe.
show hardware linecard slot—id unit unit-number register
• Display the tables from the bShell through the CLI without going into the bShell.
show hardware linecard slot—id unit unit-number table-dump {table-name}
• Display hardware statistics from the specified port extender and stack-unit. number {buffer | cpu | drops| unit}
show hardware pe pe-id stack-unit unit number {buffer | cpu | drops| unit}
• Display the system flow entries on specified port extender and the stack unit in a PE stack. The command output also
displays flow entries on port-set when there are multiple port pipes.
show hardware system-flow pe {PEID stack-unit unit number port-set port-pipe-id counters | <cr>}
• Display FP entries created for layer3 for the PE interface(s) to which the egress ACLs configurations are applied.
show hardware ip eg-acl pe pe-id stack-unit unit—number port-set number { counters | <cr> }
• Display FP entries created for layer3 for the PE interface(s) to which the ingress ACL configurations are applied.
show hardware ip in-acl pe pe-id stack-unit unit—number port-set number { counters | <cr> }
• Display FP entries created for layer 2 for the PE interface(s) to which the egress ACL configurations are applied.
show hardware mac eg-acl pe pe-id stack-unit unit—number port-set number {counters | <cr> }
• Display FP entries created for layer 2 for the PE interface(s) to which the ingress ACL configurations are applied.
show hardware mac in-acl pe pe-id stack-unit unit—number port-set number { counters | <cr> }
• Display the registers, counters, drops, buffers, and other details about the Triumph and Switch fabric.
show hardware cp-switch {counters | details | drops | port-stats | register | table-dump}
show hardware sfm sfm-unit-num {buffer {total-buffer | unit unit-num {port | total-buffer}} |
counters | details | drops | port-stats | register | table-dump}
• Display hardware system-flow information.
show hardware system-flow stack-unit 0 port-set 0 { counters | }
• Display the system-flow configuration from a specific port extender hardware component.
Show hardware system-flow pe pe—id stack-unit unit—number port-set number { counters | }
NOTE: You can also clear the system-flow statistics from the specified port extender hardware component by using the
clear hardware system-flow pe pe—id stack-unit unit—number port-set number { counters |
<cr> } command.
• Display the operational status or the internal ports that are dynamically mapped to a backplane link or control-plane trunk
group that is down.
show hardware {cp | linecard slot—id} bp-link-map
Debugging and Diagnostics 314