Manualshelf

Administrator Guide

ManualsBrandsDell ManualsAccess PlatformsC9010 Modular Chassis Switch
761762763764765766767768769770
PeGi 255/3/27 Up 1000 Mbit Full --
PeGi 255/3/28 Up 1000 Mbit Full --
PeGi 255/3/29 Up 1000 Mbit Full --
PeGi 255/3/30 Up 1000 Mbit Full --
PeGi 255/3/31 Up 1000 Mbit Full --
PeGi 255/3/32 Up 1000 Mbit Full --
PeGi 255/3/33 Up 1000 Mbit Full --
PeGi 255/3/34 Up 1000 Mbit Full --
PeGi 255/3/35 Up 1000 Mbit Full --
PeGi 255/3/36 Up 1000 Mbit Full --
PeGi 255/3/37 Up 1000 Mbit Full --
PeGi 255/3/38 Up 1000 Mbit Full --
PeGi 255/3/39 Down Auto Auto --
PeGi 255/3/40 Up 1000 Mbit Full --
PeGi 255/3/41 Down Auto Auto --
PeGi 255/3/42 Down Auto Auto --
PeGi 255/3/43 Up 1000 Mbit Full --
PeGi 255/3/44 Up 1000 Mbit Full --
PeGi 255/3/45 Up 1000 Mbit Full --
PeGi 255/3/46 Down Auto Auto --
PeGi 255/3/47 Up 1000 Mbit Full 111
PeGi 255/3/48 Up 1000 Mbit Full 111
Related
Commands
show interfaces — displays information on a specific physical interface or virtual interface.
show interfaces switchport
Display only virtual and physical interfaces in Layer 2 mode. This command displays the Layer 2 mode interfaces’ IEEE 802.1Q
tag status and VLAN membership.
C9000 Series
Syntax
show interfaces switchport [interface] [linecard slot-id]
Parameters
interface
(OPTIONAL) Enter one of the following keywords and slot/port or number
information:
● For a Port Channel interface, enter the keywords port-channel then a
number. The range is from 1 to 128.
● For a 10-Gigabit Ethernet interface, enter the keyword
TenGigabitEthernet then the slot/port (ports or port-range) information.
● For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the
slot/port (ports or port-range) information.
● Enter the keyword backup to view the backup interface for this interface.
● For a port extender Gigabit Ethernet interface, enter the keyword peGigE then
the pe-id / stack-unit / port-id information. The pe-id range is from 0 to 255;
the stack-unit unit-number range is from 0 to 7; and the port-id range is from 1
to 48.
● For a port extender 10-Gigabit Ethernet interface, enter the keyword
peTenGigE then the pe-id / stack-unit / port-id information. The pe-id range
is from 0 to 255; the stack-unit unit-numberrange is from 0 to 7; and the port-
id range is 25 to 28 or 49 to 52 depending on the PE.
NOTE: The peGigE or peTenGigE interface option is only visible when the
feature extended bridge is enabled.
linecard
slot-id
Enter the linecard slot-id parameters to specify the switch ports on a line
card. The range of slot IDs is from 0 to 11.
Command Modes
● EXEC
Interfaces 767