Administrator Guide

SFP 1 Tx Bias Current = 6.894mA
SFP 1 Tx Power = 0.328mW
SFP 1 Rx Power = 0.000mW
===================================
SFP 1 Data Ready state Bar = False
SFP 1 Rx LOS state = True
SFP 1 Tx Fault state = False
SFP 1 Rate Select state = False
SFP 1 RS state = False
SFP 1 Tx Disable state = False
===================================
SFP 1 Temperature High Alarm Flag = False
SFP 1 Voltage High Alarm Flag = False
SFP 1 Tx Bias High Alarm Flag = False
SFP 1 Tx Power High Alarm Flag = False
SFP 1 Rx Power High Alarm Flag = False
SFP 1 Temperature Low Alarm Flag = False
SFP 1 Voltage Low Alarm Flag = False
SFP 1 Tx Bias Low Alarm Flag = False
SFP 1 Tx Power Low Alarm Flag = False
SFP 1 Rx Power Low Alarm Flag = True
===================================
!-------output truncated -------------------------!
Example-
tengigabitethern
et (port-range)
Dell#show interfaces tengigabitethernet 10/0-2 transceiver
Interface Name :TenGigabitEthernet 10/0
SFP is present
SFP+ 0 Serial Base ID fields
SFP+ 0 Id = 0x03
SFP+ 0 Ext Id = 0x04
SFP+ 0 Connector = 0x07
SFP+ 0 Transceiver Code = 0x10 0x00 0x00 0x00 0x00 0x00 0x00
0x00
SFP+ 0 Encoding = 0x06
SFP+ 0 BR Nominal = 0x67
SFP+ 0 Length(SFM) Km = 0x00
SFP+ 0 Length(OM3) 2m = 0x00
SFP+ 0 Length(OM2) 1m = 0x08
SFP+ 0 Length(OM1) 1m = 0x03
SFP+ 0 Length(Copper) 1m = 0x00
SFP+ 0 Vendor Rev = A
SFP+ 0 Laser Wavelength = 850 nm
SFP+ 0 CheckCodeBase = 0x9e
SFP+ 0 Serial Extended ID fields
SFP+ 0 Options = 0x00 0x1a
SFP+ 0 BR max = 0
SFP+ 0 BR min = 0
SFP+ 0 Vendor SN = AQM1AHB
SFP+ 0 Datecode = 131122
SFP+ 0 CheckCodeExt = 0xda
SFP+ 0 Diagnostic Information
===================================
SFP+ 0 Rx Power measurement type = Average
===================================
SFP+ 0 Temp High Alarm threshold = 78.000C
SFP+ 0 Voltage High Alarm threshold = 3.700V
SFP+ 0 Bias High Alarm threshold = 13.200mA
SFP+ 0 TX Power High Alarm threshold = 1.000mW
SFP+ 0 RX Power High Alarm threshold = 1.000mW
SFP+ 0 Temp Low Alarm threshold = -13.000C
SFP+ 0 Voltage Low Alarm threshold = 2.900V
SFP+ 0 Bias Low Alarm threshold = 4.000mA
SFP+ 0 TX Power Low Alarm threshold = 0.251mW
SFP+ 0 RX Power Low Alarm threshold = 0.010mW
===================================
SFP+ 0 Temp High Warning threshold = 73.000C
SFP+ 0 Voltage High Warning threshold = 3.600V
SFP+ 0 Bias High Warning threshold = 12.600mA
Interfaces
775