Administrator Guide

################ FP Entry for redirecting LLDP BPDU to RSM ################
EID 0x000002ff: gid=0xa,
slice=9, slice_idx=0x2, part =0 prio=0x2ff, flags=0x10202, Installed, Enabled
tcam: color_indep=0,
Stage
InPorts
DATA=0x0000000000000000000000000000000000000000000000000000222222222222
MASK=0x0000000000000000000000000000000000000000000000000000222222222223
DstMac
Offset: 88 Width: 48
DATA=0x00000180 c200000e
MASK=0x0000ffff ffffffff
action={act=DropPrecedence, param0=1(0x1), param1=0(0), param2=0(0),
param3=0(0)}
action={act=Drop, param0=0(0), param1=0(0), param2=0(0), param3=0(0)}
action={act=CosQCpuNew, param0=1(0x1), param1=0(0), param2=0(0), param3=0(0)}
action={act=CopyToCpu, param0=1(0x1), param1=2(0x2), param2=0(0), param3=0(0)}
policer=
statistics={stat id 2 slice = 9 idx=0 entries=1}{Packets}
--More--
############## FP Entry for redirecting LACP traffic to CPU Port ############
EID 0x000002fd: gid=0xa,
slice=9, slice_idx=0x3, part =0 prio=0x2fd, flags=0x10202, Installed, Enabled
tcam: color_indep=0,
Stage
InPorts
DATA=0x0000000000000000000000000000000000000000000000000000222222222222
MASK=0x0000000000000000000000000000000000000000000000000000222222222223
DstMac
Offset: 88 Width: 48
DATA=0x00000180 c2000002
MASK=0x0000ffff ffffffff
action={act=DropPrecedence, param0=1(0x1), param1=0(0), param2=0(0),
param3=0(0)}
action={act=Drop, param0=0(0), param1=0(0), param2=0(0), param3=0(0)}
action={act=CosQCpuNew, param0=3(0x3), param1=0(0), param2=0(0), param3=0(0)}
action={act=CopyToCpu, param0=1(0x1), param1=4(0x4), param2=0(0), param3=0(0)}
policer=
statistics={stat id 3 slice = 9 idx=1 entries=1}{Packets}
--More--
################# FP Entry for redirecting GVRP traffic to RSM ###########
EID 0x000002fc: gid=0xa,
slice=9, slice_idx=0x4, part =0 prio=0x2fc, flags=0x10202, Installed, Enabled
tcam: color_indep=0,
Stage
InPorts
DATA=0x0000000000000000000000000000000000000000000000000000222222222222
MASK=0x0000000000000000000000000000000000000000000000000000222222222223
DstMac
Offset: 88 Width: 48
DATA=0x00000180 c2000021
MASK=0x0000ffff ffffffff
action={act=DropPrecedence, param0=1(0x1), param1=0(0), param2=0(0),
param3=0(0)}
action={act=Drop, param0=0(0), param1=0(0), param2=0(0), param3=0(0)}
action={act=CosQCpuNew, param0=4(0x4), param1=0(0), param2=0(0), param3=0(0)}
action={act=CopyToCpu, param0=1(0x1), param1=5(0x5), param2=0(0), param3=0(0)}
policer=
statistics={stat id 8 slice = 9 idx=2 entries=1}{Packets}
Viewing Per-Protocol CoPP Counters
To view per-protocol counters of rate-limited control-plane traffic, use the show control-traffic protocol [cp-
switch | [linecard {0-11} portset {0-0}] | [port-extender {0-255} stack-unit {0-7} portset
{0-0}] counters command, where:
● cp-switch displays counters for rate-limited traffic on the central switch (aggregated CoPP).
● linecard portset displays counters for rate-limited traffic on a specified switch line card and port set (distributed
CoPP).
Control Plane Policing (CoPP)
239