Administrator Guide

Dell#show running-config pe
!
feature extended-bridge
!
pe provision 200
cascade interface TenGigabitEthernet 0/22-23
stack-unit 2 type C1048P
Dell#show pe brief
-- Port Extenders Information --
----------------------------------------------------------
PE-id Status Stack-size Type System-MAC
----------------------------------------------------------
200 online 1 C1048P f8:b1:56:00:02:8a
Dell#show pe 200
Codes: A - Active, I - Inactive
SVC - Software Version Compatible
Reason: CTM - Card Type Mismatch, CAM - CAM ACL Mismatch
SVM - Software Version Mismatch, UE - Unknown Error
Offline Reason: UNP - Unit Not Present, PVE - Port Validation Error
ICE - IPC CP Error, IRE - IPC RP Error
ISE - IPC Setup Error, CVE - Card Validation Error
PE-ID assigned: 200
Status: online
System Mac: f8:b1:56:00:02:8a
PE Up Time: 00:01:57
PE Discovery Status: Provisioned PE
User Configured Cascade Ports: Te 0/22(A),Te 0/23(A)
Cascade LAG: Po 458(Up)
------------------------------------------------------------------------
Stack-id Status Reason Type UnitMac No. of Ports
-----------------------------------------------------------------
2 online - C1048P f8:b1:56:00:02:8a 52
Dell#
1. Use the upgrade bootflash-image all command to upgrade the boot-flash image in both the CB and the PE.
Dell#upgrade bootflash-image all tftp://10.16.127.35/FTOS-C9000-9.10.0.0.bin
00:08:58 : Discarded 1 pkts. Expected block num : 51. Received block num: 50
!!!!.!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!.!!.!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!.!.!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!.
Current Boot information in the system:
============================================
Card BootFlash Current Version New Version
------------------------------------------------------------------------
rpm 0 (CP) Boot Flash 3.3.1.16 3.3.1.18
rpm 0 (RP) Boot Flash 3.3.1.16 3.3.1.18
Linecard0 Boot Flash 3.3.1.16 3.3.1.18
Linecard1 Boot Flash 3.3.1.16 3.3.1.18
Linecard2 Boot Flash 3.3.1.16 3.3.1.18
Linecard3 Boot Flash 3.3.1.16 3.3.1.18
Linecard4 Boot Flash 3.3.1.16 3.3.1.18
Linecard5 Boot Flash 3.3.1.16 3.3.1.18
Linecard6 Boot Flash 3.3.1.16 3.3.1.18
Linecard7 Boot Flash 3.3.1.16 3.3.1.18
Linecard8 Boot Flash 3.3.1.16 3.3.1.18
Linecard9 Boot Flash 3.3.1.16 3.3.1.18
Linecard10 Boot Flash 3.3.1.16 3.3.1.18
Linecard11 Boot Flash 3.3.1.16 3.3.1.18
PE (0/0) Boot Flash 3.3.1.7 3.3.1.7
PE (0/1) Boot Flash 3.3.1.7 3.3.1.7
***********************************************************************
* Warning - Upgrading boot flash is inherently risky and should only *
* be attempted when necessary. A failure at this upgrade may cause *
* a board RMA. Proceed with caution ! *
***********************************************************************
Proceed Boot Flash image for all cards [yes/no]: yes
722
Port Extenders (PEs)