Administrator Guide

0 64-byte pkts, 0 over 64-byte pkts, 0 over 127-byte pkts
0 over 255-byte pkts, 0 over 511-byte pkts, 0 over 1023-byte pkts
0 Multicasts, 0 Broadcasts, 0 Unicasts
0 throttles, 0 discarded, 0 collisions, 0 wreddrops
Rate info (interval 299 seconds):
Input 00.00 Mbits/sec, 0 packets/sec, 0.00% of line-rate
Output 00.00 Mbits/sec, 0 packets/sec, 0.00% of line-rate
Time since last interface status change: 00:07:34
Usage Information
The Management port is enabled by default (no shutdown). If necessary, use the ip address command to
assign an IP address to the Management port. If two RPMs are installed in your system, use the show
redundancy command to display which RPM is the Primary RPM.
You can configure two global IPv6 addresses. To view the addresses, use the show interface
managementethernet command. If you try to configure a third IPv6 address, a message displays. If auto-
configuration is enabled, all IPv6 addresses on that management interface are auto-configured. The first IPv6
address that is configured on the management interface is the primary address. If deleted, it must be re-added;
the secondary address is not promoted.
To view information on a specific PE stack-unit, use the show interface pe pe-id stack unit unit-
number command. You can use the show interfaces peGigE command to view the information on all the
components of the PE Gigabit Ethernet interface.
To view the show output for multiple ports of a specified slot at a time, you can specify any random port number
or a range of ports, or a combination of both.
To specify a port range, you can enter a hyphenated range of one or more port range values separated with
commas; for example, show interfaces FortyGigE 1/0-4,7,9-11. To enter any random number of
ports, you can enter a comma-separated string of port numbers, for example show interfaces FortyGigE
1/0/1,9,11
NOTE: The port-range option is only available for 1 Gigabit Ethernet, 10-Gigabit Ethernet, 40-
Gigabit Ethernet, Fast Ethernet, FC, Port Channel, and VLAN interfaces.
Example
(TenGigabit
Interface)
Dell# show interfaces tengigabitethernet 2
TenGigabitEthernet 2/0 is down, line protocol is down
Hardware is DellForce10Eth, address is 74:86:7a:ff:6f:18
Current address is 74:86:7a:ff:6f:18
Pluggable media present, Media type is unknown
Wavelength is 0.00nm
Interface index is 151060994
Backup Interface of this port is Te 2/1
Internet address is not set
MTU 1554 bytes, IP MTU 1500 bytes
LineSpeed 10000 Mbit
Flowcontrol rx on tx off
ARP type: ARPA, ARP Timeout 04:00:00
Last clearing of "show interface" counters 01:22:49
Queueing strategy: fifo
Input Statistics:
0 packets, 0 bytes
0 64-byte pkts, 0 over 64-byte pkts, 0 over 127-byte pkts
0 over 255-byte pkts, 0 over 511-byte pkts, 0 over 1023-byte pkts
0 Multicasts, 0 Broadcasts
0 runts, 0 giants, 0 throttles
0 CRC, 0 overrun, 0 discarded
Output Statistics:
0 packets, 0 bytes, 0 underruns
0 64-byte pkts, 0 over 64-byte pkts, 0 over 127-byte pkts
0 over 255-byte pkts, 0 over 511-byte pkts, 0 over 1023-byte pkts
0 Multicasts, 0 Broadcasts, 0 Unicasts
0 throttles, 0 discarded, 0 collisions, 0 wreddrops
Rate info (interval 299 seconds):
Input 00.00 Mbits/sec, 0 packets/sec, 0.00% of line-rate
Output 00.00 Mbits/sec, 0 packets/sec, 0.00% of line-rate
Time since last interface status change: 01:21:35
TenGigabitEthernet 2/1 is down, line protocol is down
Interfaces
701