Setup Guide

S 11.1.1.0/24 Direct, Nu 0 0/0 00:02:30
Direct, Lo 0
--More--
The system installs a next hop that is on the directly connected subnet of current IP address on the interface (for example, if interface
gig 0/0 is on 172.31.5.0 subnet, the system installs the static route).
The system also installs a next hop that is not on the directly connected subnet but which recursively resolves to a next hop on the
interface's congured subnet. For example, if gig 0/0 has ip address on subnet 2.2.2.0 and if 172.31.5.43 recursively resolves to 2.2.2.0,
the system installs the static route.
• When the interface goes down, the system withdraws the route.
• When the interface comes up, the system re-installs the route.
• When the recursive resolution is “broken,” the system withdraws the route.
• When the recursive resolution is satised, the system re-installs the route.
Adding description for IPv4 and IPv6 static routes
Dell EMC Networking OS provides support to add a description for the IPv4 or IPv6 static route congurations. A name option is
introduced to provide the description about the static route congured. This feature enables you to segregate or distinguish between the
congured IPv4 or IPv6 static routes.
Following is the syntax of the {ip | ipv6} route command with the name option:
{ip | ipv6} route [vrf vrf-name] ip-address mask {ip-address | interface [ip-address]}
[distance] [name description] [permanent] [tag tag-value] [vrf vrf-name] [weight weight-value]
You can enter up to 32 characters as the name or description for this route. These description can be a combination of numbers, special
characters, and alphabets. To add multiple strings using space, use double quotes.
Following is the sample conguration steps to provide the descriptions for the IPv4 and IPv6 static route conguration:
DellEMC(conf)# ip route 199.1.1.0 /24 vlan 100 name "Uplink To NewYork"
DellEMC(conf)# ipv6 route 1001:1001::/64 GigabitEthernet 1/42 2001:2001::1 name
ipv6_link_going_to_europe_centre
DellEMC(conf)# ip route 19.1.1.0/24 19.1.1.1 name This_link_goes_to_London_Central
To view the description for the IPv4 or IPv6 static routes, use the show running-config static command. Following is the sample
show running-config static output:
DellEMC#show running-config static
!
ipv6 route 1::/32 GigabitEthernet 2/3 11::1 name Stack-2
ipv6 route 2::/32 GigabitEthernet 2/48 11::1 name Stack-2
ip route 2.2.2.0/24 GigabitEthernet 2/47 name Stack-2
ipv6 route 1001:1001::/64 GigabitEthernet 1/42 2001:2001::1 name
ipv6_link_going_to_europe_centre
ip route 19.1.1.0/24 19.1.1.1 name This_link_goes_to_London_Central
ipv6 route 1500:1500::/96 2500:2500::1 name Under-Sea_Links_to_Asia-Pacific
ip route 50.50.1.32/30 Vlan 210 name AZ!#$_Link_to_Asia_$#
ip route 199.1.1.0 /24 vlan 100 name "Uplink To NewYork"
ip route 100.1.1.0/24 Vlan 100 name Any_Description_upto_32_characte
ip route 199.1.1.0/24 GigabitEthernet 1/41 name Added_Description_for_StaticRoute
NOTE
: You can view the description of the congured static routes only using the show running-config static command.
IPv4 Routing 491