Messages Reference Guide

ManualsBrandsDell ManualsComputersChassis Management Controller Version 1.0 for PowerEdge VRTX

Dell PowerEdge VRTX Chassis Management

Controller Firmware

Event Message Reference Guide Version 1.0

Summary of content (931 pages)

PAGE 1
Dell PowerEdge VRTX Chassis Management Controller Firmware Event Message Reference Guide Version 1.
PAGE 2
Notes, Cautions, and Warnings NOTE: A NOTE indicates important information that helps you make better use of your computer. CAUTION: A CAUTION indicates either potential damage to hardware or loss of data and tells you how to avoid the problem. WARNING: A WARNING indicates a potential for property damage, personal injury, or death. © 2013 Dell Inc.
PAGE 3
Contents 1 Introduction................................................................................................................................45 2 AMP Event Messages.............................................................................................................. 47 AMP0300.................................................................................................................................................................47 AMP0301..............................................
PAGE 4
ASR0102.................................................................................................................................................................. 63 ASR0103.................................................................................................................................................................. 63 ASR0104...............................................................................................................................................................
PAGE 5
BAT1027.................................................................................................................................................................. 84 BAT1034.................................................................................................................................................................. 85 BAT0000...............................................................................................................................................................
PAGE 6
CMC8505............................................................................................................................................................... 107 CMC8506............................................................................................................................................................... 107 CMC8507...............................................................................................................................................................
PAGE 7
CMC8555............................................................................................................................................................... 129 CMC8557............................................................................................................................................................... 129 CMC8558...............................................................................................................................................................
PAGE 8
CPU0806................................................................................................................................................................ 151 CPU0822................................................................................................................................................................ 152 CPU0700................................................................................................................................................................
PAGE 9
CTL29.....................................................................................................................................................................175 CTL30.....................................................................................................................................................................175 CTL31...............................................................................................................................................................
PAGE 10
CTL71.....................................................................................................................................................................197 CTL72.....................................................................................................................................................................198 CTL73...............................................................................................................................................................
PAGE 11
ENC18....................................................................................................................................................................220 ENC19....................................................................................................................................................................221 ENC21.................................................................................................................................................................
PAGE 12
FCD8503.................................................................................................................................................................242 FCD8504.................................................................................................................................................................242 FCD8505.................................................................................................................................................................
PAGE 13
HWC4014...............................................................................................................................................................263 HWC4015...............................................................................................................................................................263 HWC2008...............................................................................................................................................................
PAGE 14
HWC1014...............................................................................................................................................................284 HWC4016...............................................................................................................................................................284 HWC1100...............................................................................................................................................................
PAGE 15
IOV116................................................................................................................................................................... 305 IOV115................................................................................................................................................................... 305 IOV117..............................................................................................................................................................
PAGE 16
LC056.....................................................................................................................................................................326 LC057.....................................................................................................................................................................326 LC058...............................................................................................................................................................
PAGE 17
LIC208....................................................................................................................................................................347 LIC209....................................................................................................................................................................348 LIC210..............................................................................................................................................................
PAGE 18
MEM0021.............................................................................................................................................................. 368 MEM0006.............................................................................................................................................................. 369 MEM0022..............................................................................................................................................................
PAGE 19
MEM1012.............................................................................................................................................................. 389 MEM1013.............................................................................................................................................................. 390 MEM1014..............................................................................................................................................................
PAGE 20
PCI1344................................................................................................................................................................. 409 PCI1346................................................................................................................................................................. 410 PCI1348...............................................................................................................................................................
PAGE 21
PDR9..................................................................................................................................................................... 431 PDR10....................................................................................................................................................................431 PDR11................................................................................................................................................................
PAGE 22
PDR52....................................................................................................................................................................453 PDR53....................................................................................................................................................................454 PDR54.................................................................................................................................................................
PAGE 23
PDR100..................................................................................................................................................................475 PDR101..................................................................................................................................................................476 PDR9000................................................................................................................................................................
PAGE 24
PST0131.................................................................................................................................................................498 PST0132.................................................................................................................................................................499 PST0133.................................................................................................................................................................
PAGE 25
PSU1010................................................................................................................................................................ 519 PSU1002................................................................................................................................................................ 519 PSU1004................................................................................................................................................................
PAGE 26
PSU0080................................................................................................................................................................ 541 PSU0038................................................................................................................................................................ 541 PSU0039................................................................................................................................................................
PAGE 27
PWR8530...............................................................................................................................................................562 PWR8531...............................................................................................................................................................563 PWR8532...............................................................................................................................................................
PAGE 28
PWR8575...............................................................................................................................................................584 PWR8576...............................................................................................................................................................584 PWR8577...............................................................................................................................................................
PAGE 29
PWR0105...............................................................................................................................................................605 PWR0106...............................................................................................................................................................606 PWR0107...............................................................................................................................................................
PAGE 30
RDU8501................................................................................................................................................................625 RDU8502................................................................................................................................................................626 RDU8506................................................................................................................................................................
PAGE 31
33 RFL Event Messages.............................................................................................................649 RFL2000................................................................................................................................................................. 649 RFL2002................................................................................................................................................................. 649 RFL2003.........................
PAGE 32
37 SEC Event Messages............................................................................................................671 SEC0001.................................................................................................................................................................671 SEC0002.................................................................................................................................................................671 SEC0003............................
PAGE 33
SEL0004................................................................................................................................................................. 690 SEL0006................................................................................................................................................................. 690 SEL0007...............................................................................................................................................................
PAGE 34
SEL1504................................................................................................................................................................. 709 SEL9901................................................................................................................................................................. 710 SEL9902...............................................................................................................................................................
PAGE 35
STOR032................................................................................................................................................................730 STOR033................................................................................................................................................................731 STOR035................................................................................................................................................................
PAGE 36
SUP023..................................................................................................................................................................751 41 SWC Event Messages.......................................................................................................... 753 SWC8533...............................................................................................................................................................753 SWC8534..............................
PAGE 37
SWC8531...............................................................................................................................................................773 SWC8532...............................................................................................................................................................774 SWC8600...............................................................................................................................................................
PAGE 38
SWU8520...............................................................................................................................................................796 SWU8521...............................................................................................................................................................797 SWU8522...............................................................................................................................................................
PAGE 39
SYS006.................................................................................................................................................................. 817 SYS013.................................................................................................................................................................. 817 SYS014................................................................................................................................................................
PAGE 40
TMP0121............................................................................................................................................................... 838 TMP0122............................................................................................................................................................... 838 TMP0123...............................................................................................................................................................
PAGE 41
VDR6..................................................................................................................................................................... 860 VDR7..................................................................................................................................................................... 860 VDR8................................................................................................................................................................
PAGE 42
VDR48....................................................................................................................................................................882 VDR49....................................................................................................................................................................882 VDR50.................................................................................................................................................................
PAGE 43
VLT0300................................................................................................................................................................. 905 VLT0301................................................................................................................................................................. 905 VLT0302...............................................................................................................................................................
PAGE 44
VLT0230................................................................................................................................................................. 927 VLT0231................................................................................................................................................................. 928 VLT0232...............................................................................................................................................................
PAGE 45
1 Introduction The Event Message Reference contains the error and event information generated by firmware and other agents that monitor system components. These events might be logged, presented to the user on one of the system management consoles, or both logged and displayed. Each event consists of the following fields: Message ID Message The unique alphanumeric identifier for the event.
PAGE 46
Severity 3 Information Indicates a medium-to-low impact problem that involves a partial or noncritical loss of functionality; operations are impaired but can continue to function. LCD Message The event message text that is displayed on the system's LCD. Initial Default Event messages result in event actions such as logging, SNMP or email alerts. Generally, the event actions are configurable using the Dell iDRAC event action filtering feature.
PAGE 47
2 AMP Event Messages AMP0300 The system boardarg1current is less than the lower warning threshold. Message Arguments • arg1 = name Detailed Description None Recommended Response Action Review system power policy, check system logs for power related failures, and review system configuration changes. Category System Health SubCategory AMP = Amperage Severity Severity 2 (Warning) Trap/EventID 2178 LCD Message No LCD message display defined. Initial Default.
PAGE 48
Trap/EventID 2177 LCD Message System board current is outside of range. Contact Support Initial Default. LC Log Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset TRUE FALSE TRUE TRUE FALSE FALSE FALSE TRUE FALSE AMP0302 The system boardarg1current is greater than the upper warning threshold. Message Arguments • arg1 = name Detailed Description Product documentation contains information on correct configuration.
PAGE 49
Severity Severity 1 (Critical) Trap/EventID 2177 LCD Message System board current is outside of range. Contact Support Initial Default. LC Log Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset TRUE FALSE TRUE TRUE FALSE FALSE FALSE TRUE FALSE AMP0304 The system boardarg1current is outside of range. Message Arguments • arg1 = name Detailed Description Product documentation contains information on correct configuration.
PAGE 50
SubCategory AMP = Amperage Severity Severity 3 (Informational) Trap/EventID 2179 LCD Message No LCD message display defined. Initial Default. LC Log Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset TRUE FALSE TRUE TRUE FALSE FALSE FALSE TRUE FALSE AMP0306 Disk drive bayarg1current is less than the lower warning threshold.
PAGE 51
Category System Health SubCategory AMP = Amperage Severity Severity 1 (Critical) Trap/EventID 2177 LCD Message Disk drive bay current is outside of range. Contact Support Initial Default. LC Log Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset TRUE FALSE TRUE TRUE FALSE FALSE FALSE TRUE FALSE AMP0308 Disk drive bayarg1current is greater than the upper warning threshold.
PAGE 52
Recommended Response Action Review system power policy, check system logs for power related failures, and review system configuration changes. Category System Health SubCategory AMP = Amperage Severity Severity 1 (Critical) Trap/EventID 2177 LCD Message Disk drive bay current is outside of range. Contact Support Initial Default.
PAGE 53
Detailed Description None Recommended Response Action No response action is required. Category System Health SubCategory AMP = Amperage Severity Severity 3 (Informational) Trap/EventID 2179 LCD Message No LCD message display defined. Initial Default. LC Log Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset TRUE FALSE TRUE TRUE FALSE FALSE FALSE TRUE FALSE AMP0312 Message System level current is less than the lower warning threshold.
PAGE 54
Category System Health SubCategory AMP = Amperage Severity Severity 1 (Critical) Trap/EventID FALSE LCD Message System level current is outside of range. Contact Support Initial Default. FALSE Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE AMP0314 Message System level current is greater than the upper warning threshold.
PAGE 55
Trap/EventID FALSE LCD Message System level current is outside of range. Contact Support Initial Default. FALSE Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE AMP0316 Message System level current is outside of range. Detailed Description Product documentation contains information on correct configuration. The failure could also be caused by a faulty component or related cabling.
PAGE 56
Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE AMP0318 Message Chassis power level current is less than the lower warning threshold.
PAGE 57
AMP0320 Message Chassis power level current is greater than the upper warning threshold. Detailed Description Product documentation contains information on correct configuration. The failure could also be caused by a faulty component or related cabling. System performance may be degraded.
PAGE 58
Detailed Description Product documentation contains information on correct configuration. The failure could also be caused by a faulty component or related cabling. System performance may be degraded. Recommended Response Action Review system power policy, check system logs for power related failures, and review system configuration changes Category System Health SubCategory AMP = Amperage Severity Severity 1 (Critical) Trap/EventID 2177 LCD Message No LCD message display defined.
PAGE 59
3 ASR Event Messages ASR8500 Message Watchdog timer is disabled. Detailed Description Watchdog timer is disabled. The watchdog timer is an internal mechanism used to monitor the health of the Chassis Management Controller. The watchdog timer could be disabled as part of a troubleshooting operation and can be enabled by restarting the Chassis Management Controller. Recommended Response Action No response action required.
PAGE 60
Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE ASR0001 Message The watchdog timer reset the system. Detailed Description The operating system or an application failed to communicate to the baseboard management controller (BMC) within the timeout period. The system was reset per the configured setting.
PAGE 61
ASR0003 Message The watchdog timer power cycled the system. Detailed Description The operating system or an application failed to communicate to the baseboard management controller (BMC). The system powered cycled per the configured setting. Recommended Response Action Check the operating system, application, hardware, and system event log for exception events.
PAGE 62
ASR0009 Message The system returned from a watchdog timer event. Detailed Description The system is communicating to the baseboard management controller (BMC). Recommended Response Action No response action is required. Category System Health SubCategory ASR = Auto Sys Reset Severity Severity 3 (Informational) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default.
PAGE 63
ASR0101 Message The OS watchdog timer reset the system. Detailed Description The operating system or an application failed to communicate within the timeout period. System was reset. (IPMI sensor type code 23h offset 01 - event 3:0 - 3h if booting 4h if running) Recommended Response Action Check the operating system, application, hardware, and system event log for exception events.
PAGE 64
Detailed Description The operating system or an application failed to communicate within the timeout period. The system was powered down. (IPMI sensor type code 23h offset - 02h event 3:0 - 4h) Recommended Response Action Check the operating system, application, hardware, and system event log for exception events. Category System Health SubCategory ASR = Auto Sys Reset Severity Severity 1 (Critical) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default.
PAGE 65
Category System Health SubCategory ASR = Auto Sys Reset Severity Severity 1 (Critical) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default. FALSE Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE ASR0106 Message The OS watchdog timer expired. Detailed Description The operating system or an application failed to communicate within the timeout period.
PAGE 66
Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default. FALSE Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE ASR0108 Message The system returned from an OS watchdog timer event. Detailed Description None Recommended Response Action No response action is required.
PAGE 67
4 BAT Event Messages BAT1000 Battery onarg1is missing. Message Arguments • arg1 = controller name Detailed Description The controller cannot communicate with the battery. The battery is absent or improperly connected. A battery with a weak or depleted charge may also cause this message. Recommended Response Action Verify that the device is present and then check the cables. See the storage hardware documentation to verify cabling.
PAGE 68
Severity Severity 3 (Informational) Trap/EventID 4275 LCD Message No LCD message display defined. Initial Default. SNMP Alert;#LCD;#Remote System Log Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset TRUE FALSE TRUE TRUE TRUE FALSE FALSE FALSE TRUE BAT1022 arg1battery recondition is completed. Message Arguments • arg1 = Controller name Detailed Description This alert is provided for informational purposes.
PAGE 69
SubCategory BAT = Battery Event Severity Severity 2 (Warning) Trap/EventID 4274 LCD Message No LCD message display defined. Initial Default. SNMP Alert;#LCD;#Remote System Log Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset TRUE FALSE TRUE TRUE TRUE FALSE FALSE TRUE FALSE BAT1029 The battery onarg1can no longer recharge. Message Arguments • arg1 = controller name Detailed Description The controller battery cannot recharge.
PAGE 70
Category Storage SubCategory BAT = Battery Event Severity Severity 3 (Informational) Trap/EventID 4275 LCD Message No LCD message display defined. Initial Default. SNMP Alert;#LCD;#Remote System Log Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset TRUE FALSE TRUE TRUE TRUE FALSE FALSE TRUE FALSE BAT1031 The battery temperature onarg1is above normal.
PAGE 71
Recommended Response Action No response action is required. Category Storage SubCategory BAT = Battery Event Severity Severity 3 (Informational) Trap/EventID 4275 LCD Message No LCD message display defined. Initial Default. SNMP Alert;#LCD;#Remote System Log Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset TRUE FALSE TRUE TRUE TRUE FALSE FALSE TRUE FALSE BAT1033 The battery onarg1was removed.
PAGE 72
Arguments • arg1 = controller name Detailed Description A controllers battery was replaced. Recommended Response Action No response action is required. Category Storage SubCategory BAT = Battery Event Severity Severity 3 (Informational) Trap/EventID 4275 LCD Message No LCD message display defined. Initial Default.
PAGE 73
BAT1003 The battery onarg1learn cycle has completed. Message Arguments • arg1 = Controller name Detailed Description This alert is provided for informational purposes. Recommended Response Action No response action is required. Category Storage SubCategory BAT = Battery Event Severity Severity 3 (Informational) Trap/EventID 4275 LCD Message No LCD message display defined. Initial Default.
PAGE 74
Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset TRUE FALSE TRUE TRUE TRUE FALSE FALSE FALSE TRUE BAT1005 The battery onarg1learn cycle has been postponed. Message Arguments • arg1 = Controller name Detailed Description This alert is provided for informational purposes. Recommended Response Action No response action is required.
PAGE 75
Initial Default. SNMP Alert;#LCD;#Remote System Log Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset TRUE FALSE TRUE TRUE TRUE FALSE FALSE FALSE TRUE BAT1007 The battery onarg1learn cycle will start inarg2hours. Message Arguments • • arg1 = Controller name arg2 = arg Detailed Description This alert is provided for informational purposes. Recommended Response Action No response action is required.
PAGE 76
Trap/EventID 4274 LCD Message No LCD message display defined. Initial Default. SNMP Alert;#LCD;#Remote System Log Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset TRUE FALSE TRUE TRUE TRUE FALSE FALSE FALSE TRUE BAT1009 Write policy onarg1was changed to Write Back. Message Arguments • arg1 = controller name Detailed Description The controller battery health has returned to normal.
PAGE 77
Severity Severity 2 (Warning) Trap/EventID 4274 LCD Message No LCD message display defined. Initial Default. SNMP Alert;#LCD;#Remote System Log Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset TRUE FALSE TRUE TRUE TRUE FALSE FALSE TRUE FALSE BAT1012 Thearg1battery temperature is above normal.
PAGE 78
SubCategory BAT = Battery Event Severity Severity 2 (Warning) Trap/EventID 4274 LCD Message No LCD message display defined. Initial Default. SNMP Alert;#LCD;#Remote System Log Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset TRUE FALSE TRUE TRUE TRUE FALSE FALSE TRUE FALSE BAT1014 arg1battery charge in-progress.
PAGE 79
Category Storage SubCategory BAT = Battery Event Severity Severity 3 (Informational) Trap/EventID 4275 LCD Message No LCD message display defined. Initial Default. SNMP Alert;#LCD;#Remote System Log Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset TRUE FALSE TRUE TRUE TRUE FALSE FALSE FALSE TRUE BAT1016 Thearg1battery learn mode has changed to Auto.
PAGE 80
Recommended Response Action No response action is required. Category Storage SubCategory BAT = Battery Event Severity Severity 3 (Informational) Trap/EventID 4275 LCD Message No LCD message display defined. Initial Default. SNMP Alert;#LCD;#Remote System Log Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset TRUE FALSE TRUE TRUE TRUE FALSE FALSE TRUE FALSE BAT1018 Battery onarg1is degraded.
PAGE 81
Detailed Description This alert is provided for informational purposes. Recommended Response Action No response action is required. Category Storage SubCategory BAT = Battery Event Severity Severity 3 (Informational) Trap/EventID 4275 LCD Message No LCD message display defined. Initial Default.
PAGE 82
Detailed Description The controller battery cannot maintain sufficient charge level to function properly or the battery is discharging. Recommended Response Action Check for other events related to the state of the battery. These may help determine the cause of this event. Category Storage SubCategory BAT = Battery Event Severity Severity 2 (Warning) Trap/EventID 4274 LCD Message No LCD message display defined. Initial Default.
PAGE 83
Detailed Description The battery or the battery charger is not functioning properly. The battery may have an inadequate charge. Recommended Response Action Contact technical support. Category Storage SubCategory BAT = Battery Event Severity Severity 2 (Warning) Trap/EventID 4274 LCD Message No LCD message display defined. Initial Default.
PAGE 84
BAT1026 Thearg1has recovered cached data from the Battery Backup Unit (BBU). Message Arguments • arg1 = controller name Detailed Description The controller has retrieved cached data. Recommended Response Action No response action is required. Category Storage SubCategory BAT = Battery Event Severity Severity 3 (Informational) Trap/EventID 4275 LCD Message No LCD message display defined. Initial Default.
PAGE 85
Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset TRUE FALSE TRUE TRUE TRUE FALSE FALSE FALSE TRUE BAT1034 The battery properties forarg1have changed. Message Arguments • arg1 = controller name Detailed Description One or more battery properties were modified. Recommended Response Action No response action is required.
PAGE 86
Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset TRUE FALSE TRUE TRUE FALSE FALSE FALSE FALSE TRUE BAT0001 Message The system board battery is operating normally. Detailed Description None Recommended Response Action No response action is required. Category System Health SubCategory BAT = Battery Event Severity Severity 3 (Informational) Trap/EventID 2227 LCD Message No LCD message display defined. Initial Default.
PAGE 87
BAT0003 Message The system board battery is present. Detailed Description None Recommended Response Action No response action is required. Category System Health SubCategory BAT = Battery Event Severity Severity 3 (Informational) Trap/EventID 2227 LCD Message No LCD message display defined. Initial Default.
PAGE 88
Detailed Description The system has to remain powered on to charge the battery. Recommended Response Action Allow the PERC RAID controller battery to charge. If the issue persists, contact technical support. Refer to the product documentation to choose a convenient contact method. Category System Health SubCategory BAT = Battery Event Severity Severity 2 (Warning) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default.
PAGE 89
Category System Health SubCategory BAT = Battery Event Severity Severity 1 (Critical) Trap/EventID FALSE LCD Message Storage battery has failed. Check battery. Initial Default. FALSE Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE BAT0008 Message The storage battery is present. Detailed Description None Recommended Response Action No response action is required.
PAGE 90
Trap/EventID FALSE LCD Message Storage battery is absent. Check battery. Initial Default. FALSE Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE BAT0010 The storage battery for disk drive bayarg1is low. Message Arguments • arg1 = bay Detailed Description The system has to remain powered on to charge the battery.
PAGE 91
SubCategory BAT = Battery Event Severity Severity 3 (Informational) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default. FALSE Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE BAT0012 The storage battery for disk drive bayarg1has failed.
PAGE 92
Category System Health SubCategory BAT = Battery Event Severity Severity 3 (Informational) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default. FALSE Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE BAT0014 The storage battery for disk drive bayarg1is absent.
PAGE 93
Recommended Response Action Check the battery at the next service window. Category System Health SubCategory BAT = Battery Event Severity Severity 2 (Warning) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default. FALSE Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE BAT0016 Thearg1battery is operating normally.
PAGE 94
Detailed Description System settings may be preserved if input power is not removed from the power supplies. Recommended Response Action Check the battery. Category System Health SubCategory BAT = Battery Event Severity Severity 1 (Critical) Trap/EventID FALSE LCD Message The battery has failed. Check battery. Initial Default.
PAGE 95
Detailed Description System settings may be preserved if input power is not removed from the power supplies. Recommended Response Action Check the battery to confirm presence. Category System Health SubCategory BAT = Battery Event Severity Severity 1 (Critical) Trap/EventID FALSE LCD Message The battery is absent. Check battery. Initial Default.
PAGE 96
PAGE 97
5 BOOT Event Messages BOOT8500 Unable to change the BIOS boot order for the Serverarg1 Message Arguments • arg1 = slot number Detailed Description Unable to change the BIOS boot order for the server because of a broken communication between the CMC and iDRAC, or iDRAC is rebooting. Recommended Response Action Reset iDRAC or wait until iDRAC reboots, and retry the operation.
PAGE 98
PAGE 99
6 CBL Event Messages CBL8500 SAS cablearg1to expanderarg2is not connected. Message Arguments • • arg1 = cable id arg2 = expander id Detailed Description SAS cables are not connected to the expander correctly. Recommended Response Action Check whether or not the SAS cables are connected to the expander. Reconnect the cables and rety the operation. Category Storage SubCategory CBL = Cable Severity Severity 1 (Critical) Trap/EventID FALSE LCD Message No LCD message display defined.
PAGE 100
Severity Severity 2 (Warning) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default. None Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE CBL0001 Backplanearg1power cable disconnected. Message Arguments • arg1 = Bay ID Detailed Description A backplane signal cable was detected, but the accompanying power cable was not present.
PAGE 101
SubCategory CBL = Cable Severity Severity 1 (Critical) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default. FALSE Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE CBL0003 Backplanearg1connectorarg2disconnected. No cable detected.
PAGE 102
Detailed Description None Recommended Response Action Check backplane configuration. Re-connect cable. If the issue persists, contact technical support. Refer to the product documentation to choose a convenient contact method. Category System Health SubCategory CBL = Cable Severity Severity 1 (Critical) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default.
PAGE 103
Arguments • arg1 = Bay ID Detailed Description This is an unsupported backplane configuration. Recommended Response Action Review product documentation. Check backplane configuration. If the issue persists, contact technical support. Refer to the product documentation to choose a convenient contact method. Category System Health SubCategory CBL = Cable Severity Severity 1 (Critical) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default.
PAGE 104
Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE FALSE FALSE FALSE FALSE 104 FALSE FALSE
PAGE 105
7 CMC Event Messages CMC8501 Message Chassis Group Leader has synchronized this members configuration. Detailed Description Multi Chassis Management feature on CMC allows for pushing the lead chassis configuration data to its members. This message appears in the members log when the configuration data is successfully synchronized with the Chassis group leaders configuration data. Recommended Response Action No response action required.
PAGE 106
Initial Default. LC Log Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE TRUE FALSE FALSE FALSE FALSE FALSE CMC8503 Message Unable to access the IPv4 information of the server. Detailed Description CMC is unable to access the IPv4 information for the specified server. Unable to display the specified servers Launch iDRAC link on the CMC Web interface.
PAGE 107
Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default. LC Log Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE TRUE FALSE FALSE FALSE FALSE FALSE CMC8505 Unable to access server:arg1because both IPv4 and IPv6 are disabled. NIC Enabled =arg2.
PAGE 108
SubCategory CMC = Chassis Management Controller Severity Severity 3 (Informational) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default. LC Log Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE TRUE FALSE FALSE FALSE FALSE FALSE CMC8507 Message Extended Storage for primary CMC and secondary CMC synchronization is complete.
PAGE 109
SubCategory CMC = Chassis Management Controller Severity Severity 2 (Warning) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default. LC Log Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE TRUE FALSE FALSE FALSE FALSE FALSE CMC8509 Unable to activate the extended storage feature on the secondary CMC:arg1. The feature will be deactivated.
PAGE 110
Detailed Description This happens during promotion of extended storage feature from single CMC to dual CMC. If the media on Standby CMC is not healthy, this message is displayed and the feature returns to single CMC state. Recommended Response Action Do one of the following, and retry the operation: 1) In the CMC Web interface, go to Chassis Controller > Flash Media > Configuration and verify if the card on the secondary CMC displays some errors.
PAGE 111
CMC8512 Message The Extended Storage feature activation timed out. The feature is not active. Detailed Description The Extended Storage feature is not activated if the removable flash media SD card on the secondary CMC does not respond within 90 seconds after activation is initiated. Recommended Response Action Do the following and retry the operation: 1) In the CMC Web interface, go to Chassis Controller > Flash Media > Configuration, and verify if the SD card on secondary CMC displays errors.
PAGE 112
Initial Default. SNMP Alert;#EMAIL Alert;#LC Log;#Remote System Log Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset TRUE FALSE TRUE TRUE FALSE FALSE FALSE TRUE FALSE CMC8514 Fabric mismatch is detected in the I/O Modulearg1.
PAGE 113
SubCategory CMC = Chassis Management Controller Severity Severity 2 (Warning) Trap/EventID 2546 LCD Message No LCD message display defined. Initial Default. SNMP Alert;#EMAIL Alert;#LC Log;#Remote System Log Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset TRUE FALSE TRUE TRUE FALSE FALSE FALSE TRUE FALSE CMC8517 A double height server is detected in slotarg1, however the server is not detected in the bottom slot.
PAGE 114
Recommended Response Action Do the following: 1) Remove the server identified in the message. 2) Restart the CMC and wait for the CMC to complete the start up process. 3) Reinsert the server identified in the message. If the problem persists, contact your service provider. Category System Health SubCategory CMC = Chassis Management Controller Severity Severity 1 (Critical) Trap/EventID 2545 LCD Message No LCD message display defined. Initial Default.
PAGE 115
Detailed Description FRU on the server specified in the message is not functioning or CMC is unable to read it. Recommended Response Action Do the following: 1) Reset iDRAC of the specified server or virtual reseat the server. 2) Reset CMC and wait for a few minutes. If the issue persists, contact your service provider. Category System Health SubCategory CMC = Chassis Management Controller Severity Severity 1 (Critical) Trap/EventID 2545 LCD Message No LCD message display defined.
PAGE 116
Detailed Description The Mezz card 2 FRU for the server specified in the message is not functioning or CMC is unable to read it. Recommended Response Action Do the following: 1) Reset iDRAC of the specified server or virtual reseat the server. 2) Reset CMC and wait for a few minutes. If the issue persists, contact your service provider.
PAGE 117
Detailed Description The Mezz card 4 FRU for the server specified in the message is not functioning or CMC is unable to read it. Recommended Response Action Do the following: 1) Reset iDRAC of the specified server or virtual reseat the server. 2) Reset CMC and wait for a few minutes. If the issue persists, contact your service provider.
PAGE 118
Detailed Description CMC is unable to obtain the CPU information from the server specified in the message. This occurs if there is no communication between CMC and iDRAC. Recommended Response Action Do the following: 1) Reset iDRAC. 2) Reset CMC. If the issue persists, contact your service provider. Category System Health SubCategory CMC = Chassis Management Controller Severity Severity 1 (Critical) Trap/EventID 2545 LCD Message No LCD message display defined. Initial Default.
PAGE 119
Detailed Description CMC is unable to obtain the link tuning information for the newly installed hardware (server, Input Output Module, or Mezzanine card), or is unable to send the link tuning information to iDRAC. Recommended Response Action Make sure that the currently installed CMC firmware is the latest. Otherwise, update the CMC with the latest CMC firmware and retry the operation.
PAGE 120
Arguments • arg1 = sleeve number Detailed Description The user account does not have sufficient privileges to perform virtual reseat operation on the sleeve specified in the message. Server administration privilege is required to perform virtual reseat operation. Recommended Response Action Use a different user account that has server administration privileges, and retry the operation. For more information, contact your administrator.
PAGE 121
CMC8534 Unable to turn on the serverarg1because the power requirement request exceeds the power cap value. Message Arguments • arg1 = slot number Detailed Description Unable to turn on the server specified in the message, because the available power is lesser than the requested power. Recommended Response Action In the CMC Web interface, verify the available power and server power requirements. If sufficient power is available, retry the operation. Otherwise, increase the power cap value.
PAGE 122
Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset TRUE FALSE TRUE TRUE FALSE FALSE FALSE TRUE FALSE CMC8538 Message Firmware version string is too long. Detailed Description The length of the CMC firmware version to be sent in the message from local CMC to peer CMC is too long. Under these conditions, CMC version in the message is displayed as 1.0. Recommended Response Action No response action is required.
PAGE 123
Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE TRUE FALSE FALSE FALSE FALSE FALSE CMC8540 The CMCarg1is turned on. Message Arguments • arg1 = slot id Detailed Description The CMC specified in the message is turned on because of a CMC insertion or due to chassis AC power on. Recommended Response Action No response action is required.
PAGE 124
Initial Default. LC Log Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE TRUE FALSE FALSE FALSE FALSE FALSE CMC8542 The CMCarg1was restarted because of a manual reset. Message Arguments • arg1 = slot id Detailed Description The CMC specified in the message was manually restarted. Recommended Response Action No response action is required.
PAGE 125
Severity Severity 1 (Critical) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default. LC Log Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE TRUE FALSE FALSE FALSE FALSE FALSE CMC8545 Detected a missing process failover condition detected. Process =arg1. Message Arguments • arg1 = process name Detailed Description A firmware error has occurred causing a CMC failover.
PAGE 126
Category Audit SubCategory CMC = Chassis Management Controller Severity Severity 1 (Critical) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default. LC Log Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE TRUE FALSE FALSE FALSE FALSE FALSE CMC8547 Missing kernel modulearg1.
PAGE 127
Category Audit SubCategory CMC = Chassis Management Controller Severity Severity 1 (Critical) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default. LC Log Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE TRUE FALSE FALSE FALSE FALSE FALSE CMC8550 The chassis health isarg1.
PAGE 128
Recommended Response Action No response action is required. Category Audit SubCategory CMC = Chassis Management Controller Severity Severity 1 (Critical) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default. LC Log Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE TRUE FALSE FALSE FALSE FALSE FALSE CMC8553 Message An internal error occurred and a failover condition is detected.
PAGE 129
SubCategory CMC = Chassis Management Controller Severity Severity 1 (Critical) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default. LC Log Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE TRUE FALSE FALSE FALSE FALSE FALSE CMC8555 Message An internal memory error has occurred and a failover condition is detected.
PAGE 130
Severity Severity 1 (Critical) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default. LC Log Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE TRUE FALSE FALSE FALSE FALSE FALSE CMC8558 Message The system health is restored. Detailed Description The system health has recovered from a failover condition. Recommended Response Action No response action is required.
PAGE 131
Severity Severity 2 (Warning) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default. LC Log Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE TRUE FALSE FALSE FALSE FALSE FALSE CMC8562 Message The log is cleared. Detailed Description The hardware log is cleared. Recommended Response Action No response action is required.
PAGE 132
Initial Default. SNMP Alert;#EMAIL Alert;#LC Log;#Remote System Log Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset TRUE FALSE TRUE TRUE FALSE FALSE FALSE TRUE FALSE CMC8572 The coin cell battery in CMCarg1is not working. Message Arguments • arg1 = slot id Detailed Description The coin cell battery in the CMC located in the slot specified in the message is not working. The battery needs to be replaced.
PAGE 133
LCD Message No LCD message display defined. Initial Default. LC Log Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE TRUE FALSE FALSE FALSE FALSE FALSE CMC8564 Message The KVM mapping feature is disabled. Detailed Description The KVM is not mapped to any of the server slots. Recommended Response Action No response action is required.
PAGE 134
Initial Default. LC Log Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE TRUE FALSE FALSE FALSE FALSE FALSE CMC8566 KVM mapping is disabled for the server slotarg1. Message Arguments • arg1 = slot number Detailed Description The KVM mapping is disabled for the server slot specified in the message. The KVM can not be mapped to this server slot. Recommended Response Action No response action is required.
PAGE 135
LCD Message No LCD message display defined. Initial Default. LC Log Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE TRUE FALSE FALSE FALSE FALSE FALSE CMC8568 Message The DVD drive mapping feature is disabled. Detailed Description The DVD drive is disabled and is not mapped to any of the server slots. Recommended Response Action No response action is required.
PAGE 136
Initial Default. LC Log Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE TRUE FALSE FALSE FALSE FALSE FALSE CMC8570 The server slotarg1is disabled for DVD drive mapping. Message Arguments • arg1 = slot number Detailed Description The server slot specified in the message is disabled for DVD drive mapping. The DVD drive can not be mapped to this server slot. Recommended Response Action No response action is required.
PAGE 137
LCD Message No LCD message display defined. Initial Default.
PAGE 138
PAGE 139
8 CPU Event Messages CPU0000 CPUarg1has an internal error (IERR). Message Arguments • arg1 = number Detailed Description System event log and OS logs may indicate that the exception is external to the processor. Recommended Response Action Review System Event Log and Operating System Logs. If the issue persists, contact technical support. Refer to the product documentation to choose a convenient contact method.
PAGE 140
Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default. FALSE Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE CPU0001 CPUarg1has a thermal trip (over-temperature) event. Message Arguments • arg1 = number Detailed Description The processor temperature increased beyond the operational range. Thermal protection shut down the processor.
PAGE 141
SubCategory CPU = Processor Severity Severity 1 (Critical) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default. FALSE Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE CPU0003 CPUarg1is stuck in POST. Message Arguments • arg1 = number Detailed Description None Recommended Response Action 1) Turn system off and remove input power for one minute.
PAGE 142
Recommended Response Action 1) Turn system off and remove input power for one minute. Re-apply input power and turn system on. 2) Make sure the processor is seated correctly. 3) If the issue still persists, contact technical support. Refer to the product documentation to choose a convenient contact method. Category System Health SubCategory CPU = Processor Severity Severity 1 (Critical) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default.
PAGE 143
Detailed Description None Recommended Response Action No response action is required. Category System Health SubCategory CPU = Processor Severity Severity 3 (Informational) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default. FALSE Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE CPU0006 Unrecoverable CPU complex error detected on CPUarg1.
PAGE 144
Arguments • arg1 = number Detailed Description None Recommended Response Action No response action is required. Category System Health SubCategory CPU = Processor Severity Severity 3 (Informational) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default. FALSE Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE CPU0008 CPUarg1is disabled.
PAGE 145
CPU0024 CPUarg1is enabled. Message Arguments • arg1 = number Detailed Description None Recommended Response Action No response action is required. Category System Health SubCategory CPU = Processor Severity Severity 3 (Informational) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default.
PAGE 146
Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE CPU0025 CPUarg1terminator is absent. Message Arguments • arg1 = number Detailed Description System is unable to boot or may run in a degraded state. Recommended Response Action Check presence and reinstall the terminator.
PAGE 147
Initial Default. FALSE Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE CPU0800 CPUarg1voltage regulator module is present. Message Arguments • arg1 = number Detailed Description None Recommended Response Action No response action is required.
PAGE 148
LCD Message CPU voltage regulator module absent. Check module Initial Default. FALSE Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE CPU0801 CPUarg1voltage regulator module failed. Message Arguments • arg1 = number Detailed Description System performance may be degraded or the system may fail to operate.
PAGE 149
Severity Severity 3 (Informational) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default. FALSE Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE CPU0802 A predictive failure detected on CPUarg1voltage regulator module. Message Arguments • arg1 = number Detailed Description System performance may be degraded or the system may fail to operate.
PAGE 150
Category System Health SubCategory CPU = Processor Severity Severity 1 (Critical) Trap/EventID FALSE LCD Message Lost power input for CPU voltage regulator module. Reseat module Initial Default. FALSE Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE CPU0819 The power input for CPUarg1voltage regulator module has been restored.
PAGE 151
Recommended Response Action 1) Turn system off and remove input power for one minute. Re-apply input power and turn system on. 2) Make sure the processor is seated correctly. 3) If the issue still persists, contact technical support. Refer to the product documentation to choose a convenient contact method. Category System Health SubCategory CPU = Processor Severity Severity 1 (Critical) Trap/EventID FALSE LCD Message Power input for CPU voltage regulator module is outside of range.
PAGE 152
Arguments • arg1 = number Detailed Description System performance may be degraded or the system may fail to operate. Recommended Response Action Review product documentation for proper configuration and installation procedures. Category System Health SubCategory CPU = Processor Severity Severity 1 (Critical) Trap/EventID FALSE LCD Message CPU voltage regulator module incorrectly configure. Check configuration Initial Default.
PAGE 153
CPU0700 CPUarg1initialization error detected. Message Arguments • arg1 = number Detailed Description System BIOS was unable to boot the processor. Recommended Response Action 1) Turn system off and remove input power for one minute. Re-apply input power and turn system on. 2) Make sure the processor is seated correctly. 3) If the issue still persists, contact technical support. Refer to the product documentation to choose a convenient contact method.
PAGE 154
Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE CPU0702 Message CPU bus parity error detected. Detailed Description System event log and OS logs may indicate that the exception is external to the processor. Recommended Response Action Check system and operating system logs for exceptions. If no exceptions found, remove input power, reinstall the processor, then apply input power.
PAGE 155
Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE CPU0704 CPUarg1machine check error detected. Message Arguments • arg1 = number Detailed Description System event log and OS logs may indicate that the exception is external to the processor. Recommended Response Action 1) Check system and operating system logs for exceptions. If no exceptions are found continue.
PAGE 156
Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE CPU0011 Uncorrectable Machine Check Exception detected on CPUarg1. Message Arguments • arg1 = number Detailed Description None. Recommended Response Action Review System Event Log and Operating System Logs. If the issue persists, contact technical support. Refer to the product documentation to choose a convenient contact method.
PAGE 157
Initial Default.
PAGE 158
PAGE 159
9 CPUA Event Messages CPUA0023 CPUarg1is absent Message Arguments • arg1 = number Detailed Description None Recommended Response Action Verify processor installation. If present, reseat the processor. Category System Health SubCategory CPUA = Proc Absent Severity Severity 1 (Critical) Trap/EventID FALSE LCD Message CPU is absent. Check CPU Initial Default.
PAGE 160
PAGE 161
10 CTL Event Messages CTL1 Controller event log:arg1 Message Arguments • arg1 = message Detailed Description This event is retrieved from the controller when iDRAC storage monitoring was not running. Such events which are generated in the past are logged as informational severity. Recommended Response Action No response action is required. Category Storage SubCategory CTL = Storage Contr Severity Severity 3 (Informational) Trap/EventID 4331 LCD Message No LCD message display defined.
PAGE 162
Trap/EventID 4331 LCD Message No LCD message display defined. Initial Default. SNMP Alert;#LCD;#Remote System Log Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset TRUE FALSE TRUE TRUE TRUE FALSE FALSE TRUE FALSE CTL3 arg1alarm is enabled. Message Arguments • arg1 = Controller name Detailed Description You have enabled the controller alarm. This alert is provided for informational purposes.
PAGE 163
Severity Severity 3 (Informational) Trap/EventID 4331 LCD Message No LCD message display defined. Initial Default. SNMP Alert;#LCD;#Remote System Log Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset TRUE FALSE TRUE TRUE TRUE FALSE FALSE TRUE FALSE CTL5 Bad block replacement error onarg1. Message Arguments • arg1 = Controller name Detailed Description A portion of a physical disk is damaged.
PAGE 164
SubCategory CTL = Storage Contr Severity Severity 2 (Warning) Trap/EventID 4330 LCD Message No LCD message display defined. Initial Default. SNMP Alert;#LCD;#Remote System Log Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset TRUE FALSE TRUE TRUE TRUE FALSE FALSE TRUE FALSE CTL7 Bad block medium error onarg1. Message Arguments • arg1 = Controller name Detailed Description A portion of a physical disk is damaged.
PAGE 165
Category Storage SubCategory CTL = Storage Contr Severity Severity 2 (Warning) Trap/EventID 4330 LCD Message No LCD message display defined. Initial Default. SNMP Alert;#LCD;#Remote System Log Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset TRUE FALSE TRUE TRUE TRUE FALSE FALSE TRUE FALSE CTL9 Bad block extended medium error onarg1.
PAGE 166
Recommended Response Action No response action is required. Category Storage SubCategory CTL = Storage Contr Severity Severity 3 (Informational) Trap/EventID 4331 LCD Message No LCD message display defined. Initial Default. SNMP Alert;#LCD;#Remote System Log Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset TRUE FALSE TRUE TRUE TRUE FALSE FALSE TRUE FALSE CTL11 Configuration onarg1was reset.
PAGE 167
Detailed Description The controller and attached enclosures are not cabled correctly. Recommended Response Action Refer to the storage hardware documentation for information on correct cabling configurations. Category Storage SubCategory CTL = Storage Contr Severity Severity 1 (Critical) Trap/EventID 4329 LCD Message No LCD message display defined. Initial Default.
PAGE 168
Arguments • arg1 = Controller name Detailed Description The controller memory is malfunctioning. Recommended Response Action Replace the controller, contact Dell technical support at support.dell.com. Category Storage SubCategory CTL = Storage Contr Severity Severity 2 (Warning) Trap/EventID 4330 LCD Message No LCD message display defined. Initial Default.
PAGE 169
CTL17 arg1arg2is changed toarg3. Message Arguments • • • arg1 = Controller Name arg2 = propertyname arg3 = new value Detailed Description This alert is provided for informational purposes. Recommended Response Action No response action is required. Category Storage SubCategory CTL = Storage Contr Severity Severity 3 (Informational) Trap/EventID 4331 LCD Message No LCD message display defined. Initial Default.
PAGE 170
Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset TRUE FALSE TRUE TRUE TRUE FALSE FALSE TRUE FALSE CTL19 Abort CC on Error, Copyback, and Load Balance has changed forarg1. Message Arguments • arg1 = Controller name Detailed Description This alert is provided for informational purposes. Recommended Response Action Re-issue the command.
PAGE 171
Initial Default. SNMP Alert;#LCD;#Remote System Log Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset TRUE FALSE TRUE TRUE TRUE FALSE FALSE FALSE TRUE CTL21 Abort CC on Error and Load Balance has changed forarg1. Message Arguments • arg1 = Controller name Detailed Description This alert is provided for informational purposes. Recommended Response Action Re-issue the command.
PAGE 172
LCD Message No LCD message display defined. Initial Default. SNMP Alert;#LCD;#Remote System Log Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset TRUE FALSE TRUE TRUE TRUE FALSE FALSE TRUE FALSE CTL23 Copyback and Auto Copyback on Predictive Failure has changed forarg1. Message Arguments • arg1 = Controller name Detailed Description This alert is provided for informational purposes. Recommended Response Action Re-issue the command.
PAGE 173
Trap/EventID 4331 LCD Message No LCD message display defined. Initial Default. SNMP Alert;#LCD;#Remote System Log Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset TRUE FALSE TRUE TRUE TRUE FALSE FALSE FALSE TRUE CTL25 Auto Copyback on Predictive Failure has changed forarg1. Message Arguments • arg1 = Controller name Detailed Description This alert is provided for informational purposes. Recommended Response Action Re-issue the command.
PAGE 174
Severity Severity 3 (Informational) Trap/EventID 4331 LCD Message No LCD message display defined. Initial Default. SNMP Alert;#LCD;#Remote System Log Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset TRUE FALSE TRUE TRUE TRUE FALSE FALSE FALSE TRUE CTL27 Thearg1alarm is silenced. Message Arguments • arg1 = Controller name Detailed Description This alert is provided for informational purposes.
PAGE 175
SubCategory CTL = Storage Contr Severity Severity 3 (Informational) Trap/EventID 4331 LCD Message No LCD message display defined. Initial Default. SNMP Alert;#LCD;#Remote System Log Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset TRUE FALSE TRUE TRUE TRUE FALSE FALSE FALSE TRUE CTL29 The Patrol Read rate has changed forarg1.
PAGE 176
Category Storage SubCategory CTL = Storage Contr Severity Severity 3 (Informational) Trap/EventID 4331 LCD Message No LCD message display defined. Initial Default. SNMP Alert;#LCD;#Remote System Log Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset TRUE FALSE TRUE TRUE TRUE FALSE FALSE FALSE TRUE CTL31 Copyback is modified forarg1.
PAGE 177
Recommended Response Action Re-issue the command. Category Storage SubCategory CTL = Storage Contr Severity Severity 3 (Informational) Trap/EventID 4331 LCD Message No LCD message display defined. Initial Default. SNMP Alert;#LCD;#Remote System Log Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset TRUE FALSE TRUE TRUE TRUE FALSE FALSE FALSE TRUE CTL33 Thearg1debug log file has been exported.
PAGE 178
Detailed Description This is the result of a user operation. Recommended Response Action No response action is required. Category Storage SubCategory CTL = Storage Contr Severity Severity 3 (Informational) Trap/EventID 4331 LCD Message No LCD message display defined. Initial Default.
PAGE 179
Detailed Description This alert is provided for informational purposes. Recommended Response Action No response action is required. Category Storage SubCategory CTL = Storage Contr Severity Severity 3 (Informational) Trap/EventID 4331 LCD Message No LCD message display defined. Initial Default.
PAGE 180
Detailed Description The patrol read task ended. Recommended Response Action No response action is required. Category Storage SubCategory CTL = Storage Contr Severity Severity 3 (Informational) Trap/EventID 4331 LCD Message No LCD message display defined. Initial Default.
PAGE 181
Detailed Description An error involving multiple bits has been encountered during a read or write operation. The error correction algorithm recalculates parity data during read and write operations. If an error involves only a single bit, it may be possible for the error correction algorithm to correct the error and maintain parity data. An error involving multiple bits, however, generally indicates data loss.
PAGE 182
CTL42 Enclosure Management Module (EMM) hot plug is not supported onarg1. Message Arguments • arg1 = Controller name Detailed Description An attempt to hot plug an Enclosure Management Module (EMM) has been detected. Recommended Response Action If the new enclosure and its device are not detected by the operating system, try restarting your system to verify the newly attached enclosure and its sub-components are detected. See the hardware documentation for more information.
PAGE 183
Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset TRUE FALSE TRUE TRUE TRUE FALSE FALSE TRUE FALSE CTL44 Diagnostic messagearg1fromarg2 Message Arguments • • arg1 = message arg2 = Controller name Detailed Description A diagnostics test failed. The text for this message is generated by the tool that ran the diagnostics and can vary depending on the situation.
PAGE 184
LCD Message No LCD message display defined. Initial Default. SNMP Alert;#LCD;#Remote System Log Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset TRUE FALSE TRUE TRUE TRUE FALSE FALSE TRUE FALSE CTL46 Single-bit ECC error. Thearg1DIMM is critically degraded. Message Arguments • arg1 = Controller name Detailed Description The Dual In-line Memory Module (DIMM) is malfunctioning. Data loss or data corruption may occur..
PAGE 185
Severity Severity 1 (Critical) Trap/EventID 4329 LCD Message No LCD message display defined. Initial Default. SNMP Alert;#LCD;#Remote System Log Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset TRUE FALSE TRUE TRUE TRUE FALSE FALSE TRUE FALSE CTL48 A foreign configuration was detected onarg1.
PAGE 186
Recommended Response Action No response action is required as the controller is taking the required corrective action. However, If this message is generated often (such as during each reboot), then replace the controller. Category Storage SubCategory CTL = Storage Contr Severity Severity 2 (Warning) Trap/EventID 4330 LCD Message No LCD message display defined. Initial Default.
PAGE 187
Detailed Description The text for this message is generated by the controller during runtime and can vary depending on the situation. Recommended Response Action Make sure the SAS cables attached to the enclosure/backplane are attached securely. Refer to the storage hardware documentation for more information on checking the cables. Contact technical support if the issue persists.
PAGE 188
Detailed Description This alert is provided for informational purposes. Recommended Response Action No response action is required. Category Storage SubCategory CTL = Storage Contr Severity Severity 3 (Informational) Trap/EventID 4331 LCD Message No LCD message display defined. Initial Default.
PAGE 189
Arguments • • arg1 = Controller name arg2 = args Detailed Description The text for this alert is generated by the controller and can vary depending on the situation. This text is from events in the controller event log that were generated while Storage Management was not running. Recommended Response Action If there is a problem, review the controller event log and the Server Administrator alert log for significant events or alerts that may assist in diagnosing the problem.
PAGE 190
Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset TRUE FALSE TRUE TRUE TRUE FALSE FALSE TRUE FALSE CTL57 The factory default settings were restored onarg1. Message Arguments • arg1 = controller Name Detailed Description The controller was reset to factory default configuration settings. Recommended Response Action No response action is required.
PAGE 191
Trap/EventID 4329 LCD Message No LCD message display defined. Initial Default. SNMP Alert;#LCD;#Remote System Log Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset TRUE FALSE TRUE TRUE TRUE FALSE FALSE TRUE FALSE CTL59 arg1SAS expander error:arg2 Message Arguments • • arg1 = Controller name arg2 = args Detailed Description There may be a problem with the enclosure. Verify the health of the enclosure and its components.
PAGE 192
Recommended Response Action No response action is required. Category Storage SubCategory CTL = Storage Contr Severity Severity 3 (Informational) Trap/EventID 4331 LCD Message No LCD message display defined. Initial Default. SNMP Alert;#LCD;#Remote System Log Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset TRUE FALSE TRUE TRUE TRUE FALSE FALSE TRUE FALSE CTL61 Physical disks found missing from configuration during boot time onarg1.
PAGE 193
Detailed Description Physical disk(s) have been removed from a virtual disk. The virtual disk will be in Failed state during the next system reboot. This alert is provided for informational purposes. Recommended Response Action No response action is required. Category Storage SubCategory CTL = Storage Contr Severity Severity 3 (Informational) Trap/EventID 4331 LCD Message No LCD message display defined. Initial Default.
PAGE 194
Arguments • • arg1 = args arg2 = Controller name Detailed Description This alert is provided for informational purposes. Recommended Response Action No response action is required. Category Storage SubCategory CTL = Storage Contr Severity Severity 3 (Informational) Trap/EventID 4331 LCD Message No LCD message display defined. Initial Default.
PAGE 195
CTL66 Attempted to import Unsupported Virtual Disk type RAIDarg1onarg2. Message Arguments • • arg1 = args arg2 = Controller name Detailed Description This alert is provided for informational purposes. Recommended Response Action No response action is required. Category Storage SubCategory CTL = Storage Contr Severity Severity 3 (Informational) Trap/EventID 4331 LCD Message No LCD message display defined. Initial Default.
PAGE 196
Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset TRUE FALSE TRUE TRUE TRUE FALSE FALSE TRUE FALSE CTL68 Attempted to import Virtual Disk with missing Physical Disk onarg1. Message Arguments • arg1 = Controller name Detailed Description This alert is provided for informational purposes. Recommended Response Action No response action is required.
PAGE 197
Initial Default. SNMP Alert;#LCD;#Remote System Log Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset TRUE FALSE TRUE TRUE TRUE FALSE FALSE FALSE TRUE CTL70 Attempted to import an orphan drive onarg1. Message Arguments • arg1 = Controller name Detailed Description This alert is provided for informational purposes. Recommended Response Action No response action is required.
PAGE 198
LCD Message No LCD message display defined. Initial Default. SNMP Alert;#LCD;#Remote System Log Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset TRUE FALSE TRUE TRUE TRUE FALSE FALSE TRUE FALSE CTL72 The foreign configuration overflow has occurred onarg1. Message Arguments • arg1 = Controller name Detailed Description There is too much foreign configuration data to be imported in one attempt.
PAGE 199
Trap/EventID 4331 LCD Message No LCD message display defined. Initial Default. SNMP Alert;#LCD;#Remote System Log Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset TRUE FALSE TRUE TRUE TRUE FALSE FALSE TRUE FALSE CTL74 Preserved cache detected onarg1. Message Arguments • arg1 = controller name Detailed Description The controller has preserved data in the cache from a virtual disk, which it can no longer locate.
PAGE 200
Severity Severity 2 (Warning) Trap/EventID 4330 LCD Message No LCD message display defined. Initial Default. SNMP Alert;#LCD;#Remote System Log Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset TRUE FALSE TRUE TRUE TRUE FALSE FALSE FALSE TRUE CTL78 Firmware imagearg1is flashing onarg2. Message Arguments • • arg1 = args arg2 = Controller Name Detailed Description This alert message occurs if controller firmware is flashed.
PAGE 201
Category Storage SubCategory CTL = Storage Contr Severity Severity 3 (Informational) Trap/EventID 4331 LCD Message No LCD message display defined. Initial Default.
PAGE 202
Recommended Response Action Replace the controller with a supported controller. Category Storage SubCategory CTL = Storage Contr Severity Severity 2 (Warning) Trap/EventID 4330 LCD Message No LCD message display defined. Initial Default. None Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset TRUE FALSE TRUE TRUE TRUE FALSE FALSE TRUE FALSE CTL80 arg1experienced the following warning during startup:arg2.
PAGE 203
Detailed Description The controller experienced a problem during statup. The message from the controller is recorded in the Lifecycle Log. Recommended Response Action For the list of possible remedies for this warning, see Troubleshooting section in the Dell Shared PowerEdge RAID Controller (SPERC8) documentation. Category Storage SubCategory CTL = Storage Contr Severity Severity 1 (Critical) Trap/EventID 4329 LCD Message No LCD message display defined. Initial Default.
PAGE 204
Detailed Description The management controller cannot communicate with the storage controller. This may be due to a loss of functionality in the PCIe subsystem, a failure in the storage controller, or a failure of the management controller. Recommended Response Action Restart the system. If the controller does not come back online after a restart contact your service provider.
PAGE 205
Arguments • arg1 = controller name Detailed Description The controller experienced a PCIe training error and is operating at less than full bandwith. Users may notice a reduction in storage perforumance until this is corrected. Recommended Response Action Powercycle the chassis. If the controller does not report optimal speed after the powercycle contact your service provider.
PAGE 206
PAGE 207
11 DKM Event Messages DKM1000 Message A network problem detected. Cannot contact key management server. Detailed Description None Recommended Response Action Check for network connectivity. Review network, server, and client configuration. Category System Health SubCategory DKM = Dell Key Mngr Severity Severity 1 (Critical) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default.
PAGE 208
Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE DKM1002 Message Key management server certificate problem detected. Detailed Description None Recommended Response Action Check server configuration and certificates Category System Health SubCategory DKM = Dell Key Mngr Severity Severity 1 (Critical) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default.
PAGE 209
DKM1006 Message Key management server error detected. Detailed Description None Recommended Response Action Review server error logs for additional information. Category System Health SubCategory DKM = Dell Key Mngr Severity Severity 1 (Critical) Trap/EventID FALSE LCD Message Key management server error. Check configuration Initial Default.
PAGE 210
PAGE 211
12 ENC Event Messages ENC40 A new enclosure was detected onarg1. Message Arguments • arg1 = controller name Detailed Description The controller detected a new enclosure. This is due either to a hot plug of an enclosure, or a power state change of an enclosure. In addition, this message is generated if the daisy chain order of the enclosures changes. Recommended Response Action No response action is required.
PAGE 212
Severity Severity 3 (Informational) Trap/EventID 4339 LCD Message No LCD message display defined. Initial Default. SNMP Alert;#LCD;#Remote System Log Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset TRUE FALSE TRUE TRUE TRUE FALSE FALSE TRUE FALSE ENC2 arg1was removed.. Message Arguments • arg1 = Enclosure Management Module Name Detailed Description An Enclosure Management Module (EMM) was removed.
PAGE 213
Category Storage SubCategory ENC = Storage Enclosr Severity Severity 1 (Critical) Trap/EventID 4337 LCD Message No LCD message display defined. Initial Default. SNMP Alert;#LCD;#Remote System Log Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset TRUE FALSE TRUE TRUE TRUE FALSE FALSE TRUE FALSE ENC4 arg1firmware mismatch.
PAGE 214
Recommended Response Action Identify and replace the failed component. To identify the failed component, select the enclosure in the tree view and click the Health subtab. Any failed component will be identified with a red X on the enclosures Health subtab. Alternatively, you can select the Storage object and click the Health subtab. The controller status displayed on the Health subtab indicates whether a controller has a failed or degraded component.
PAGE 215
Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset TRUE FALSE TRUE TRUE TRUE FALSE FALSE TRUE FALSE ENC7 Thearg1alarm was enabled. Message Arguments • arg1 = Enclosure Name Detailed Description You have enabled the enclosure alarm. This alert is provided for informational purposes. Recommended Response Action No response action is required.
PAGE 216
Initial Default. SNMP Alert;#LCD;#Remote System Log Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset TRUE FALSE TRUE TRUE TRUE FALSE FALSE TRUE FALSE ENC9 Thearg1asset tag was changed. Message Arguments • arg1 = Enclosure Name Detailed Description You have changed the enclosure asset tag. This alert is provided for informational purposes. Recommended Response Action No response action is required.
PAGE 217
LCD Message No LCD message display defined. Initial Default. SNMP Alert;#LCD;#Remote System Log Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset TRUE FALSE TRUE TRUE TRUE FALSE FALSE TRUE FALSE ENC11 Thearg1service tag was changed. Message Arguments • arg1 = Enclosure Name Detailed Description An enclosure service tag was changed. In most circumstances, this service tag should only be changed by Dell support.
PAGE 218
Trap/EventID 4339 LCD Message No LCD message display defined. Initial Default. SNMP Alert;#LCD;#Remote System Log Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset TRUE FALSE TRUE TRUE TRUE FALSE FALSE TRUE FALSE ENC13 Unsupported configuration detected onarg1.arg2arg3 Message Arguments • • • arg1 = Enclosure Name arg2 = EMM0 1 arg3 = EMM1 2 Detailed Description An unsupported configuration was detected.
PAGE 219
Recommended Response Action Remove the extra enclosures. Refer to the storage hardware documentation for maximum number of enclosures that can be connected. Category Storage SubCategory ENC = Storage Enclosr Severity Severity 1 (Critical) Trap/EventID 4337 LCD Message No LCD message display defined. Initial Default.
PAGE 220
Detailed Description This alert is provided for informational purposes. Recommended Response Action No response action is required. Category Storage SubCategory ENC = Storage Enclosr Severity Severity 3 (Informational) Trap/EventID 4339 LCD Message No LCD message display defined. Initial Default.
PAGE 221
Detailed Description The controller has lost communication with an Enclosure Management Module (EMM). The cables may be loose or defective. Recommended Response Action Make sure the cables are attached securely. See the storage hardware documentation for more information on checking the cables. Reboot the system. Category Storage SubCategory ENC = Storage Enclosr Severity Severity 1 (Critical) Trap/EventID 4337 LCD Message No LCD message display defined. Initial Default.
PAGE 222
Arguments • arg1 = Enclosure elements name Detailed Description A device has been removed and the system is no longer functioning in optimal condition. Recommended Response Action Replace the device. Category Storage SubCategory ENC = Storage Enclosr Severity Severity 1 (Critical) Trap/EventID 4337 LCD Message No LCD message display defined. Initial Default.
PAGE 223
ENC23 arg1Bad PHYarg2 Message Arguments • • arg1 = Enclosure Name arg2 = args Detailed Description There is a problem with a physical connection or PHY. Recommended Response Action Contact the Dell Technical Support at support.dell.com. Category Storage SubCategory ENC = Storage Enclosr Severity Severity 1 (Critical) Trap/EventID 4337 LCD Message No LCD message display defined. Initial Default.
PAGE 224
Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset TRUE FALSE TRUE TRUE TRUE FALSE FALSE TRUE FALSE ENC25 arg1has a hardware error. Message Arguments • arg1 = enclosure name Detailed Description The enclosure or an enclosure component is in a Failed or Degraded state. Recommended Response Action Verify the health of the enclosure and its components. See the storage hardware documentation for more information. Contact technical support.
PAGE 225
Initial Default. SNMP Alert;#LCD;#Remote System Log Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset TRUE FALSE TRUE TRUE TRUE FALSE FALSE TRUE FALSE ENC27 SAS or SATA mixing of physical disks is not supported within thearg1. Message Arguments • arg1 = Enclosure Name Detailed Description The enclosure cannot support both SAS and SATA physical disks. Physical disks may be disabled. This alert is provided for informational purposes.
PAGE 226
Severity Severity 2 (Warning) Trap/EventID 4338 LCD Message No LCD message display defined. Initial Default. SNMP Alert;#LCD;#Remote System Log Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset TRUE FALSE TRUE TRUE TRUE FALSE FALSE FALSE TRUE ENC29 arg1temperature has returned to normal. Message Arguments • arg1 = Enclosure Name Detailed Description This alert is provided for informational purposes.
PAGE 227
SubCategory ENC = Storage Enclosr Severity Severity 3 (Informational) Trap/EventID 4339 LCD Message No LCD message display defined. Initial Default. SNMP Alert;#LCD;#Remote System Log Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset TRUE FALSE TRUE TRUE TRUE FALSE FALSE TRUE FALSE ENC31 Firmware download onarg1has failed.
PAGE 228
Recommended Response Action No response action is required. Category Storage SubCategory ENC = Storage Enclosr Severity Severity 3 (Informational) Trap/EventID 4339 LCD Message No LCD message display defined. Initial Default. SNMP Alert;#LCD;#Remote System Log Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset TRUE FALSE TRUE TRUE TRUE FALSE FALSE TRUE FALSE ENC33 Redundancy onarg1is normal.
PAGE 229
13 FAN Event Messages FAN8500 Message Enhanced Cooling Mode is Enabled Detailed Description Enabling Enhanced Cooling Mode will provide increased airflow capability to the blades by increasing the maximum allowable blower speed at the cost of increased power consumption. Recommended Response Action No response action is required. Category Audit SubCategory FAN = Fan Event Severity Severity 3 (Informational) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default.
PAGE 230
Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FAN8502 The blowerarg1is not detected, because it may not be operating optimally. Check for the availability of latest CMC firmware. Message Arguments • arg1 = name Detailed Description The current CMC firmware did not detect the blower identified in the message. To resolve the issue, update the firmware.
PAGE 231
Initial Default. SNMP Alert;#LCD;#Remote System Log Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset TRUE FALSE TRUE TRUE TRUE FALSE FALSE TRUE FALSE FAN1002 arg1has failed. Message Arguments • arg1 = Fan Sensor Name Detailed Description The enclosure detected that a fan has failed and the enclosure is no longer functioning in optimal condition.. Recommended Response Action Contact technical support.
PAGE 232
LCD Message No LCD message display defined. Initial Default. SNMP Alert;#LCD;#Remote System Log Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset TRUE FALSE TRUE TRUE TRUE FALSE FALSE TRUE FALSE FAN0000 Fanarg1RPM is less than the lower warning threshold. Message Arguments • arg1 = number Detailed Description The fan is not performing optimally. The fan may be installed improperly or may be failing.
PAGE 233
Severity Severity 1 (Critical) Trap/EventID 2153 LCD Message Fan RPM is outside of range. Check fan. Initial Default. LC Log Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset TRUE FALSE TRUE TRUE FALSE FALSE FALSE TRUE FALSE FAN0002 Fanarg1RPM is greater than the upper warning threshold. Message Arguments • arg1 = number Detailed Description The fan is not performing optimally.
PAGE 234
Category System Health SubCategory FAN = Fan Event Severity Severity 1 (Critical) Trap/EventID 2153 LCD Message Fan RPM is outside of range. Check fan. Initial Default. LC Log Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset TRUE FALSE TRUE TRUE FALSE FALSE FALSE TRUE FALSE FAN0004 Fanarg1RPM is outside of range. Message Arguments • arg1 = number Detailed Description The fan is not performing optimally.
PAGE 235
Recommended Response Action No response action is required. Category System Health SubCategory FAN = Fan Event Severity Severity 3 (Informational) Trap/EventID 2155 LCD Message No LCD message display defined. Initial Default. LC Log Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset TRUE FALSE TRUE TRUE FALSE FALSE FALSE FALSE TRUE FAN0006 Fanarg1is removed.
PAGE 236
Detailed Description None Recommended Response Action No response action is required. Category System Health SubCategory FAN = Fan Event Severity Severity 3 (Informational) Trap/EventID 2155 LCD Message No LCD message display defined. Initial Default. LC Log Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset TRUE FALSE TRUE TRUE FALSE FALSE FALSE FALSE TRUE FAN0008 Fanarg1is present.
PAGE 237
Detailed Description The fan may be required for optimal performance. Recommended Response Action If unintentional, install a fan. Category System Health SubCategory FAN = Fan Event Severity Severity 1 (Critical) Trap/EventID 2153 LCD Message Fan is absent. Check Fan. Initial Default. LC Log Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset TRUE FALSE TRUE TRUE FALSE FALSE FALSE FALSE TRUE FAN0010 Fanarg1is disabled.
PAGE 238
Detailed Description None Recommended Response Action No response action is required. Category System Health SubCategory FAN = Fan Event Severity Severity 3 (Informational) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default. FALSE Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FAN0013 arg1RPM is less than the lower critical threshold.
PAGE 239
Detailed Description The cooling device is not performing optimally. The cooling device may be installed improperly or may be failing. Recommended Response Action Remove and re-install the cooling device. If the issue persists, contact technical support. Refer to the product documentation to choose a convenient contact method. Category System Health SubCategory FAN = Fan Event Severity Severity 1 (Critical) Trap/EventID 2153 LCD Message No LCD message display defined. Initial Default.
PAGE 240
PAGE 241
14 FCD Event Messages FCD8500 Unable to apply thearg1configuration. The affected servers (slotarg2) are not turned off. Message Arguments • • arg1 = configuration name arg2 = slot number Detailed Description The server specified in the message must be turned off or the server slot must be empty before changing the FlexAddress configuration. Recommended Response Action Turn off the server and retry the operation.
PAGE 242
Severity Severity 1 (Critical) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default. LC Log Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE TRUE FALSE FALSE FALSE FALSE FALSE FCD8503 The feature is activated in the chassis:arg1 Message Arguments • arg1 = feature name Detailed Description Chassis already has the feature identified in the message activated.
PAGE 243
Severity Severity 3 (Informational) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default. LC Log Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE TRUE FALSE FALSE FALSE FALSE FALSE FCD8505 Message The features cannot be deactivated when the chassis is turned on. Detailed Description Features cannot be be deactivated when the chassis is turned on.
PAGE 244
Severity Severity 1 (Critical) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default.
PAGE 245
15 HWC Event Messages HWC8502 Message The KVM interconnect is connected. Detailed Description The KVM cable is connected. Recommended Response Action No response action is required. Category System Health SubCategory HWC = Hardware Config Severity Severity 3 (Informational) Trap/EventID 2331 LCD Message No LCD message display defined. Initial Default.
PAGE 246
Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset TRUE FALSE TRUE TRUE TRUE FALSE FALSE FALSE TRUE HWC8503 Message The control panel is online Detailed Description The control panel is available Recommended Response Action No response action is required. Category System Health SubCategory HWC = Hardware Config Severity Severity 3 (Informational) Trap/EventID 2331 LCD Message No LCD message display defined. Initial Default.
PAGE 247
HWC8505 Control panel firmware updatearg1complete Message Arguments • arg1 = version Detailed Description The control panel firmware has been updated Recommended Response Action No response action is required. Category System Health SubCategory HWC = Hardware Config Severity Severity 3 (Informational) Trap/EventID 2331 LCD Message No LCD message display defined. Initial Default.
PAGE 248
HWC1001 Thearg1is absent. Message Arguments • arg1 = name Detailed Description The absent device may be necessary for proper operation. System functionality may be degraded. Recommended Response Action Re-install or reconnect the hardware. Category System Health SubCategory HWC = Hardware Config Severity Severity 1 (Critical) Trap/EventID FALSE LCD Message The is absent. Check hardware Initial Default.
PAGE 249
Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE HWC1002 Thearg1is disabled. Message Arguments • arg1 = name Detailed Description None Recommended Response Action If device disabled unexpectedly, re-enable device. Category System Health SubCategory HWC = Hardware Config Severity Severity 3 (Informational) Trap/EventID FALSE LCD Message No LCD message display defined.
PAGE 250
Initial Default. FALSE Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE HWC1005 Message The storage adapter is absent. Detailed Description The storage adapter may be necessary for proper operation. System functionality may be degraded. Recommended Response Action Install storage adapter.
PAGE 251
Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE HWC1006 Message The storage adapter is disabled. Detailed Description None Recommended Response Action If adapter disabled unexpectedly, re-enable the storage adapter. Category System Health SubCategory HWC = Hardware Config Severity Severity 3 (Informational) Trap/EventID FALSE LCD Message No LCD message display defined.
PAGE 252
HWC2000 Thearg1cable or interconnect is connected. Message Arguments • arg1 = name Detailed Description None Recommended Response Action No response action is required. Category System Health SubCategory HWC = Hardware Config Severity Severity 3 (Informational) Trap/EventID 2331 LCD Message No LCD message display defined. Initial Default.
PAGE 253
Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset TRUE FALSE TRUE TRUE FALSE FALSE FALSE FALSE TRUE HWC2002 The storagearg1cable or interconnect is connected. Message Arguments • arg1 = name Detailed Description None Recommended Response Action No response action is required. Category System Health SubCategory HWC = Hardware Config Severity Severity 3 (Informational) Trap/EventID 2331 LCD Message No LCD message display defined.
PAGE 254
Initial Default. LC Log Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset TRUE FALSE TRUE TRUE FALSE FALSE FALSE FALSE TRUE HWC2004 The system boardarg1cable or interconnect is connected. Message Arguments • arg1 = name Detailed Description None Recommended Response Action No response action is required.
PAGE 255
LCD Message System board cable or interconnect failure. Check connection Initial Default. LC Log Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset TRUE FALSE TRUE TRUE FALSE FALSE FALSE TRUE FALSE HWC1009 Message The backplane is absent. Detailed Description The backplane may be necessary for proper operation. System functionality may be degraded.
PAGE 256
Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE HWC1010 Message The backplane is disabled. Detailed Description None Recommended Response Action If disabled unexpectedly, re-enable backplane. Category System Health SubCategory HWC = Hardware Config Severity Severity 3 (Informational) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default.
PAGE 257
HWC3000 Thearg1is removed. Message Arguments • arg1 = name Detailed Description The removed device may be necessary for proper operation. System functionality may be degraded. Recommended Response Action If removal was unintended, check presence, then re-install or reconnect Category System Health SubCategory HWC = Hardware Config Severity Severity 1 (Critical) Trap/EventID 2329 LCD Message No LCD message display defined. Initial Default.
PAGE 258
Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset TRUE FALSE TRUE TRUE FALSE FALSE FALSE TRUE FALSE HWC2006 Thearg1is not installed correctly. Message Arguments • arg1 = name Detailed Description The device may be necessary for proper operation. System functionality may be degraded. Recommended Response Action Check presence, then re-install or reconnect.
PAGE 259
Initial Default. FALSE Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE HWC4000 Message A hardware incompatibility detected between BMC/iDRAC firmware and CPU. Detailed Description A hardware incompatibility was detected between BMC/iDRAC firmware and Processor(s). An iDRAC or BMC firmware update is needed. Recommended Response Action Update the BMC/iDRAC firmware.
PAGE 260
Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE HWC4002 Message A hardware incompatibility detected between BMC/iDRAC firmware and other hardware. Detailed Description A hardware incompatibility was detected between BMC/iDRAC firmware and other hardware. An iDRAC or BMC firmware update is needed. Recommended Response Action Update the BMC/iDRAC firmware.
PAGE 261
HWC4010 Hardware successfully updated for mezzanine cardarg1. Message Arguments • arg1 = number Detailed Description None Recommended Response Action No response action is required. Category System Health SubCategory HWC = Hardware Config Severity Severity 3 (Informational) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default.
PAGE 262
Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE HWC4012 Message Hardware successfully updated for embedded NIC. Detailed Description None Recommended Response Action No response action is required. Category System Health SubCategory HWC = Hardware Config Severity Severity 3 (Informational) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default.
PAGE 263
HWC4014 Message Link Tuning data successfully updated. Detailed Description None Recommended Response Action No response action is required. Category System Health SubCategory HWC = Hardware Config Severity Severity 3 (Informational) Trap/EventID 2331 LCD Message No LCD message display defined. Initial Default.
PAGE 264
Arguments • arg1 = number Detailed Description The fabric type for the IOM and mezzanine cards must match. Once an IOM or mezzanine card is inserted into the chassis, the fabric type is then set for the CMC and the CMC will ensure that all subsequent IOMs and mezzanine cards match. Recommended Response Action Check chassis fabric type in CMC GUI and compare to the type of IOM or mezzanine card.
PAGE 265
HWC2010 Message The riser board cable or interconnect is connected. Detailed Description None Recommended Response Action No response action is required. Category System Health SubCategory HWC = Hardware Config Severity Severity 3 (Informational) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default.
PAGE 266
Detailed Description The USB cable may be necessary for proper operation. System functionality may be degraded. Recommended Response Action If removal was unintended, check presence, then re-install or reconnect. Category System Health SubCategory HWC = Hardware Config Severity Severity 1 (Critical) Trap/EventID FALSE LCD Message The USB cable is absent. Check cable Initial Default.
PAGE 267
Detailed Description None Recommended Response Action No response action is required. Category System Health SubCategory HWC = Hardware Config Severity Severity 3 (Informational) Trap/EventID 2331 LCD Message No LCD message display defined. Initial Default. LC Log Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset TRUE FALSE TRUE TRUE FALSE FALSE FALSE FALSE TRUE HWC5001 arg1is offline.
PAGE 268
Detailed Description The fabric type for the IOM and mezzanine cards must match. Once an IOM or mezzanine card is inserted into the chassis, the fabric type is then set for the CMC and the CMC will ensure that all subsequent IOMs and mezzanine cards match. Recommended Response Action Check chassis fabric type in CMC GUI and compare to the type of IOM or mezzanine card.
PAGE 269
Arguments • arg1 = name Detailed Description CMC has old firmware and does not recognize the new device which has requested link tuning information. After updating the firmware the CMC will recognize the device. Recommended Response Action Update the CMC firmware. If the problem persists, contact support. Category System Health SubCategory HWC = Hardware Config Severity Severity 2 (Warning) Trap/EventID 2330 LCD Message No LCD message display defined. Initial Default.
PAGE 270
HWC5008 Console is not available for thearg1. Message Arguments • arg1 = name Detailed Description None Recommended Response Action Contact technical support. Refer to your product documentation to choose the contact method that is convenient for you. Category System Health SubCategory HWC = Hardware Config Severity Severity 2 (Warning) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default.
PAGE 271
Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE HWC5012 On screen display (OSCAR) is not functional for thearg1. Message Arguments • arg1 = name Detailed Description None Recommended Response Action Contact technical support. Refer to your product documentation to choose the contact method that is convenient for you.
PAGE 272
Initial Default. FALSE Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE HWC5030 IO modulearg1is online. Message Arguments • arg1 = number Detailed Description None Recommended Response Action No response action is required. Category System Health SubCategory HWC = Hardware Config Severity Severity 3 (Informational) Trap/EventID 2331 LCD Message No LCD message display defined.
PAGE 273
LCD Message No LCD message display defined. Initial Default. LC Log Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset TRUE FALSE TRUE TRUE FALSE FALSE FALSE TRUE FALSE HWC5032 A fabric mismatch detected on IO modulearg1. Message Arguments • arg1 = number Detailed Description The fabric type for IOMs on the same chassis fabric must match. Recommended Response Action Check chassis fabric type in CMC GUI and compare to the type of both IOMs.
PAGE 274
Trap/EventID 2331 LCD Message No LCD message display defined. Initial Default. LC Log Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset TRUE FALSE TRUE TRUE FALSE FALSE FALSE TRUE FALSE HWC5034 A link tuning failure detected on IO modulearg1. Message Arguments • arg1 = number Detailed Description Link tuning table not supported for this IO modular. Recommended Response Action Update the CMC firmware.
PAGE 275
Severity Severity 1 (Critical) Trap/EventID 2329 LCD Message No LCD message display defined. Initial Default. LC Log Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset TRUE FALSE TRUE TRUE FALSE FALSE FALSE FALSE TRUE HWC3002 Serverarg1is removed.
PAGE 276
SubCategory HWC = Hardware Config Severity Severity 3 (Informational) Trap/EventID 2331 LCD Message No LCD message display defined. Initial Default. LC Log Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset TRUE FALSE TRUE TRUE FALSE FALSE FALSE FALSE TRUE HWC3004 IO modulearg1is removed.
PAGE 277
Category System Health SubCategory HWC = Hardware Config Severity Severity 3 (Informational) Trap/EventID 2331 LCD Message No LCD message display defined. Initial Default. LC Log Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset TRUE FALSE TRUE TRUE FALSE FALSE FALSE FALSE TRUE HWC7000 Serverarg1health changed to a normal state.
PAGE 278
Recommended Response Action Review System Log or front panel for additional information. Category System Health SubCategory HWC = Hardware Config Severity Severity 2 (Warning) Trap/EventID 2330 LCD Message No LCD message display defined. Initial Default.
PAGE 279
Detailed Description Server health changed to a non-recoverable state from a less severe state. Recommended Response Action Review System Log or front panel for additional information. Category System Health SubCategory HWC = Hardware Config Severity Severity 1 (Critical) Trap/EventID 2329 LCD Message No LCD message display defined. Initial Default.
PAGE 280
Detailed Description Server health changed to a critical state from a non-recoverable state. Recommended Response Action Review System Log or front panel for additional information. Category System Health SubCategory HWC = Hardware Config Severity Severity 1 (Critical) Trap/EventID 2329 LCD Message No LCD message display defined. Initial Default.
PAGE 281
Detailed Description Information and status from the controller is unavailable. Recommended Response Action Remove and reapply input power. If problem persists, contact technical support. Refer to the product documentation to choose a convenient contact method. Category System Health SubCategory HWC = Hardware Config Severity Severity 2 (Warning) Trap/EventID 2330 LCD Message No LCD message display defined. Initial Default.
PAGE 282
Detailed Description Information and status from the controller is unavailable. Recommended Response Action Remove and reapply input power. If problem persists, contact technical support. Refer to the product documentation to choose a convenient contact method. Category System Health SubCategory HWC = Hardware Config Severity Severity 1 (Critical) Trap/EventID 2329 LCD Message No LCD message display defined. Initial Default.
PAGE 283
Detailed Description Information and status from the controller is unavailable. Recommended Response Action Remove and reapply input power. If problem persists, contact technical support. Refer to the product documentation to choose a convenient contact method. Category System Health SubCategory HWC = Hardware Config Severity Severity 1 (Critical) Trap/EventID 2329 LCD Message No LCD message display defined. Initial Default.
PAGE 284
Detailed Description The mezzanine card may be necessary for proper operation. System functionality may be degraded. Recommended Response Action If removal was unintended, check presence, then re-install or reconnect. Category System Health SubCategory HWC = Hardware Config Severity Severity 1 (Critical) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default.
PAGE 285
Detailed Description The system has detected a mezzanine card that is not supported on this system. Recommended Response Action 1) Review system documentation for supported mezzanine cards. 2) Replace mezzanine card with a supported mezzanine card. Category System Health SubCategory HWC = Hardware Config Severity Severity 1 (Critical) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default.
PAGE 286
Arguments • • arg1 = name arg2 = number Detailed Description None Recommended Response Action No response action is required. Category System Health SubCategory HWC = Hardware Config Severity Severity 3 (Informational) Trap/EventID 2331 LCD Message No LCD message display defined. Initial Default.
PAGE 287
HWC2013 Fabric mismatch corrected on fabricarg1with server in slotarg2. Message Arguments • • arg1 = name arg2 = number Detailed Description None Recommended Response Action No response action is required. Category System Health SubCategory HWC = Hardware Config Severity Severity 3 (Informational) Trap/EventID 2331 LCD Message No LCD message display defined. Initial Default.
PAGE 288
Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset TRUE FALSE TRUE TRUE FALSE FALSE FALSE FALSE TRUE HWC2015 Thearg1is configured correctly. Message Arguments • arg1 = name Detailed Description None. Recommended Response Action No response action is required. Category System Health SubCategory HWC = Hardware Config Severity Severity 3 (Informational) Trap/EventID 2331 LCD Message No LCD message display defined. Initial Default.
PAGE 289
LCD Message No LCD message display defined. Initial Default. LC Log Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset TRUE FALSE TRUE TRUE FALSE FALSE FALSE TRUE FALSE HWC5037 I/O modulearg1failed to boot. Message Arguments • arg1 = number Detailed Description The firmware on the I/O module did not boot. The problem may be because the I/O module is not inserted correctly. Recommended Response Action Reseat I/O module.
PAGE 290
Severity Severity 1 (Critical) Trap/EventID 2329 LCD Message No LCD message display defined. Initial Default. LC Log Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset TRUE FALSE TRUE TRUE FALSE FALSE FALSE FALSE TRUE HWC1200 Thearg1was inserted in slotarg2. Message Arguments • • arg1 = name arg2 = number Detailed Description None Recommended Response Action No response action is required.
PAGE 291
16 IOV Event Messages IOV000 Message Successfully completed the operation. Detailed Description This operation was successful. Recommended Response Action No response action is required. Category Configuration SubCategory IOV = IO Virtualization Severity Severity 3 (Informational) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default.
PAGE 292
Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset TRUE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE IOV002 Message Unable to create or allocate the required resources. Detailed Description The error occurs because of the following reasons: 1) The chassis manager is unable to allocate required resources. 2) The chassis manager or chassis infrastructure firmware is rolled back to an older version.
PAGE 293
Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset TRUE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE IOV004 Message Unable to turn on PCIe device.
PAGE 294
Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset TRUE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE IOV006 Message Incorrect IOV component firmware version. Detailed Description The IOV subsystem is comprised of several entities whose firmware versions must be of the same group. User should not update indiviual IOV ssystem sub-components.
PAGE 295
IOV008 Message Chassis manager was unable to put PCIe subsystem into factory mode Detailed Description Chassis manager was unable to put PCIe subsystem into factory mode Recommended Response Action Retry command Category Configuration SubCategory IOV = IO Virtualization Severity Severity 3 (Informational) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default.
PAGE 296
Arguments • • • arg1 = device name arg2 = slot type arg3 = slot number Detailed Description The Chassis manager has detected the presence of an adapter card in a slot not previously occupied. Recommended Response Action No response action is required. Category Configuration SubCategory IOV = IO Virtualization Severity Severity 3 (Informational) Trap/EventID 10747 LCD Message No LCD message display defined. Initial Default.
PAGE 297
Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset TRUE FALSE TRUE TRUE FALSE FALSE FALSE TRUE FALSE IOV103 PCIE devicearg1inarg2arg3replaced by PCIE devicearg4, Message Arguments • • • • arg1 = device name arg2 = slot type arg3 = slot number arg4 = device name Detailed Description The Chassis manager has detected the insertion of an adapter card into a slot previously occuppied. Recommended Response Action No response action is required.
PAGE 298
Severity Severity 2 (Warning) Trap/EventID 2554 LCD Message No LCD message display defined. Initial Default. SNMP Alert;#EMAIL Alert;#LCD;#LC Log Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset TRUE FALSE TRUE TRUE TRUE FALSE FALSE TRUE FALSE IOV105 Unable to manage PCIE devicearg1located inarg2arg3.
PAGE 299
Detailed Description The Chassis manager is unable to power on adapter. Possible reasons for power failures are: 1. Adapter not a approved by Dell and therefore not within require specifications 2. Adpater not fully inserted in the slot 3. Auxiliary power cable not connected (applicable to slot 1 - 3 only) 4, Adapter is damaged Recommended Response Action Make sure a supported PCIe device is used and that it is properly inserted in the PCIe slot.
PAGE 300
IOV108 Power fault detected on PCIE devicearg1inarg2arg3. Message Arguments • • • arg1 = device name arg2 = slot type arg3 = slot number Detailed Description The Chassis manager detected a power fault in an adapter after the adapter was powered on. A power fauilt may be caused a damaged adapter or an adapter whose power requirements exceed the maximum power limits of the slot. Recommended Response Action Make sure a supported PCIe device is used and that it is properly inserted in the PCIe slot.
PAGE 301
Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset TRUE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE IOV011 Message To assign or unassign all affected servers must be powered down. Detailed Description All affected servers must be powered down before an assign or unassign action can be performed. Recommended Response Action Power down affected server(s).
PAGE 302
IOV013 Message A server may only be assigned one and only one VA. Detailed Description A server may not have more than one VA assigned. Recommended Response Action Unassign the current VA assignement. Category Configuration SubCategory IOV = IO Virtualization Severity Severity 3 (Informational) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default.
PAGE 303
Detailed Description Successfully updated chassis infrastructure firmware. Recommended Response Action No resposne action is required. Category System Health SubCategory IOV = IO Virtualization Severity Severity 3 (Informational) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default.
PAGE 304
Category System Health SubCategory IOV = IO Virtualization Severity Severity 1 (Critical) Trap/EventID 2553 LCD Message No LCD message display defined. Initial Default. SNMP Alert;#EMAIL Alert;#LCD;#LC Log;#Remote System Log Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset TRUE FALSE TRUE TRUE TRUE FALSE FALSE FALSE TRUE IOV113 Message Chassis infrastructure firmware recovered.
PAGE 305
Recommended Response Action No response action is required. Category Configuration SubCategory IOV = IO Virtualization Severity Severity 3 (Informational) Trap/EventID 10747 LCD Message No LCD message display defined. Initial Default. LC Log Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset TRUE FALSE TRUE TRUE FALSE FALSE FALSE TRUE FALSE IOV116 PCIE AUX power cablearg1.disconnected while powered on.
PAGE 306
Detailed Description The discovery process for PCIE adapters was unable to allocate the power required to power on the PCIE adapters Recommended Response Action Raise power cap or add power supply Category Configuration SubCategory IOV = IO Virtualization Severity Severity 2 (Warning) Trap/EventID 10746 LCD Message No LCD message display defined. Initial Default.
PAGE 307
IOV118 IOV Fabricarg1is down Message Arguments • arg1 = Fabric ID Detailed Description IOV Fabric B or C is not up. Recommended Response Action Power cycle the chassis Category System Health SubCategory IOV = IO Virtualization Severity Severity 1 (Critical) Trap/EventID 2553 LCD Message No LCD message display defined. Initial Default.
PAGE 308
Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset TRUE FALSE TRUE TRUE TRUE FALSE FALSE TRUE FALSE IOV120 arg1PCIe card module without a PCIe card is discovered in PCIe slotarg2 Message Arguments • • arg1 = x8/x16 arg2 = slot number Detailed Description The Chassis manager has discovered the presence of a PCIe card module without a PCIe card in it in a slot identified in the message. Recommended Response Action No response action is required.
PAGE 309
Initial Default.
PAGE 310
LCD Message No LCD message display defined. Initial Default. SNMP Alert;#LCD;#LC Log;#Remote System Log Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset TRUE FALSE TRUE TRUE TRUE FALSE FALSE TRUE FALSE IOV124 Power fault cleared on PCIe device in PCIe slotarg1 Message Arguments • arg1 = slot number Detailed Description The previously occured power fault on the PCIe device is cleared.
PAGE 311
Trap/EventID 2555 LCD Message No LCD message display defined. Initial Default. SNMP Alert;#LCD;#LC Log;#Remote System Log Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset TRUE FALSE TRUE TRUE TRUE FALSE FALSE TRUE FALSE IOV126 Message Unable to communicate with PCIe subsystem Detailed Description The Chassis manager is not able to communicate with the PCIE subsystem to configure the PCIE slot mapping.
PAGE 312
Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE IOV1002 Message The operation was not successful. Detailed Description The operation did not complete successfully due to an exception from the instrumentation layer. Recommended Response Action Retry the operation. If the issue persists, reset CMC and retry the operation when the CMC has completed restarting.
PAGE 313
Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE IOV1004 Message Too many slots provided as parameters to Assign and UnAssign Servers methods. Detailed Description The parameters for the method identified in the message are not passed correctly. Recommended Response Action Refer to the Dell Chassis PCI Management Profile document and provide the required parameters.
PAGE 314
Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE IOV1006 Message Invalid PCI slot or Server slot. Detailed Description The PCI slot or Server slot FQDD (Fully Qualified Device Descriptor) values entered for the operation are not valid.
PAGE 315
Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE IOV1008 Invalid Virtual Adapter FQDDarg1. Message Arguments • arg1 = FQDD value Detailed Description The FQDD (Fully Qualified Device Descriptior) value entered operation does not map to any DCIM_ChassisVAView class instance representing Virtual Adapters.
PAGE 316
Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE FALSE FALSE FALSE FALSE 316 FALSE FALSE
PAGE 317
17 JCP Event Messages JCP8501 Job ID:arg1. CMC sentarg2ofarg3arg4profilesarg5arg6properties to the server (Service Tag:arg7) in the slotarg8. Message Arguments • • • • • • • • arg1 = job ID arg2 = number of applied settings arg3 = number of available settings arg4 = profile name arg5 = profile type arg6 = info_str arg7 = service tag arg8 = slot number Detailed Description This job information message occurs if some configuration stored in the profile are not applicable to the target server.
PAGE 318
Recommended Response Action Retry the update and schedule the update job. Category Configuration SubCategory JCP = Job Control Severity Severity 2 (Warning) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default. FALSE Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE JCP004 Message Time elapsed - Job Failed.
PAGE 319
SubCategory JCP = Job Control Severity Severity 3 (Informational) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default. FALSE Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE JCP008 Message Job completed with errors. Detailed Description Multiple attributes were set in the operation but some set attribute actions were not successful.
PAGE 320
SubCategory JCP = Job Control Severity Severity 2 (Warning) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default. FALSE Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE JCP012 Message The operation failed due to an internal iDRAC error. Detailed Description The requested operation requires memory or file space allocation.
PAGE 321
Severity Severity 2 (Warning) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default. FALSE Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE JCP014 Message Maximum jobs per queue exceeded.
PAGE 322
SubCategory JCP = Job Control Severity Severity 2 (Warning) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default. FALSE Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE JCP016 Message Invalid UntilTime value. A minimum of 12 minutes is required.
PAGE 323
SubCategory JCP = Job Control Severity Severity 2 (Warning) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default. FALSE Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE JCP022 Invalid Job IDarg1for scheduling or deletion operation.
PAGE 324
Recommended Response Action One of the job ID values specified as input is duplicated. Remove the duplicated Job ID from the operation input parameters and retry the operation. Category Configuration SubCategory JCP = Job Control Severity Severity 2 (Warning) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default.
PAGE 325
18 LC Event Messages LC054 Message Unable to write to the network share. Detailed Description The network share may be read-only or it may not have sufficient space for the export operation.. Recommended Response Action Verify the network share is not read-only and has sufficient space for exporting, then retry the operation. Category Configuration SubCategory LC = Lifecycle Contr Severity Severity 2 (Warning) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default.
PAGE 326
Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE LC056 Message AttributeName and AttributeValue count mismatch. Detailed Description The name value pairs in the input parameter arrays do not match in the input. Recommended Response Action Retry the operation with a valid (AttributeName, AttributeValue) pair.
PAGE 327
LC058 Invalid AttributeValue parameter value for corresponding AttributeName value,arg1. Message Arguments • arg1 = AttributeName Detailed Description The attribute value specified in the AttributeValue array is not valid for the corresponding specified attribute. Recommended Response Action Retry the operation with a valid attribute value for the corresponding specified attribute.
PAGE 328
Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE LC0100 Message Lifecycle Controller has entered Recovery mode. Detailed Description A persistent error has occurred while carrying out a Lifecycle Controller operation. This situation causes Lifecycle Controller to enter Recovery mode. Any remote jobs pending execution were cancelled.
PAGE 329
LC060 Message Lifecycle controller is currently not ready to take provisioning requests Detailed Description Lifecycle controller is currently performing tasks and another task cannot be scheduled until the previous task finishes. Recommended Response Action Wait until Lifecycle controller finishes performing current tasks and host system to finish POST.
PAGE 330
Detailed Description Export or Import server profile operation is already running. The operation may take a few minutes to compete. Recommended Response Action To retry the operation, wait for a few minutes. Category Configuration SubCategory LC = Lifecycle Contr Severity Severity 2 (Warning) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default.
PAGE 331
Detailed Description The maximum number of characters allowed for the parameter is displayed. Recommended Response Action Reduce the number of characters to the maximum length allowed for this parameter. Category Configuration SubCategory LC = Lifecycle Contr Severity Severity 2 (Warning) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default.
PAGE 332
PAGE 333
19 LIC Event Messages LIC501 Message A required license is missing or expired. Detailed Description The attempted action requires a valid license for certain advanced features installed in the system but the required license is missing or expired. Recommended Response Action Obtain an appropriate license then try again. If the problem persists, contact technical support. Refer to your product documentation to choose the contact method that is convenient for you.
PAGE 334
Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE LIC503 Message Unable to complete the current operation. The currently installed license does not support the following features:arg1. Arguments • arg1 = licensable features Detailed Description The currently installed license does not support the feature for the requested operation.
PAGE 335
Initial Default. FALSE Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE LIC001 Message The License Manager command parameter used is invalid. Detailed Description The command or command parameters passed to License Manager is invalid. This is an internal error indicative of memory corruption. Under normal circumstances this error should not occur.
PAGE 336
LCD Message No LCD message display defined. Initial Default. FALSE Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE LIC003 Message License Manager was unable to create and/or allocate the required resources. Detailed Description System resources may be unavailable at the time command is issued. Recommended Response Action Re-issue the command.
PAGE 337
Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default. FALSE Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE LIC005 Message Import failed: The maximum number of licenses are installed. Detailed Description The maximum number of installed licenses has been reached. Recommended Response Action Delete one of the currently installed licenses and retry the import.
PAGE 338
Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE LIC007 Message Invalid entry: Object does not exist or cannot be found. Detailed Description Each License Manager object has a unique identifier by which it may be accessed. If the user supplied identifier is outside the acceptable range or the object no longer exists in the system, then this error is returned.
PAGE 339
Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE LIC009 Message The license upgrade was unsuccessful. Detailed Description An upgrade license carries specific information about the license it is replacing. If that information does not match, then the license import is aborted. Recommended Response Action Obtain a new license file with the correct upgrade information.
PAGE 340
Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE LIC011 Message A non-evaluation license cannot be replaced with an evaluation license. Detailed Description License Manager does not allow the replacement of a non-evaluation license with an evaluation license.
PAGE 341
Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE LIC013 Message These license features are not supported by this firmware version. Detailed Description The license includes features not supported in this firmware release. Recommended Response Action Update the firmware to the latest version.
PAGE 342
Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE LIC015 Message The License Manager database restore operation failed. Detailed Description This error occurs when the Lifecycle Controller restore operation is interrupted before it completes. This can occur due to a power outage or when a system is rebooted before the operation is completed.
PAGE 343
Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE LIC017 Message The license file is corrupted, has not been unzipped, or is not a valid license file. Detailed Description This error can occur when the license file: 1) Signature is not valid. 2) Data is not in the correct format. 3) Missing needed data. 4) Contains unknown data. 5) Has not been unzipped.
PAGE 344
LIC019 Message A leased license may not be imported prior to its start date. Detailed Description A leased license may not be imported prior to the actual start date of the license. Recommended Response Action Import the license on or after the license start date. Category Audit SubCategory LIC = Licensing Severity Severity 2 (Warning) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default.
PAGE 345
LIC021 Message Import failed: The features contained in the evaluation license are already licensed. Detailed Description All the features in the evaluation license are currently licensed in the system. The license is not imported as it would duplicate existing and active licensed features. Recommended Response Action Remove the license(s) that contain the license set from the evaluation license.
PAGE 346
Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE LIC203 The licensearg1has encountered an error. Message Arguments • arg1 = entitlement ID Detailed Description Signature verification failed due to an error in the saved license file. Recommended Response Action Delete and re-import the license file.
PAGE 347
Initial Default. SNMP Alert;#EMAIL Alert;#LC Log;#Remote System Log Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset TRUE FALSE TRUE TRUE FALSE FALSE FALSE TRUE FALSE LIC207 Licensearg1on devicearg2has expired. Message Arguments • • arg1 = entitlement ID arg2 = device name Detailed Description The license has expired. This could result in the loss of functionality that is specific to the features supported by the license.
PAGE 348
Trap/EventID 8515 LCD Message No LCD message display defined. Initial Default. SNMP Alert;#EMAIL Alert;#LC Log;#Remote System Log Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset TRUE FALSE TRUE TRUE FALSE FALSE FALSE FALSE TRUE LIC209 Licensearg1exported from devicearg2successfully. Message Arguments • • arg1 = entitlement ID arg2 = device name Detailed Description A license was successfully exported.
PAGE 349
SubCategory LIC = Licensing Severity Severity 3 (Informational) Trap/EventID 8515 LCD Message No LCD message display defined. Initial Default. SNMP Alert;#EMAIL Alert;#LC Log;#Remote System Log Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset TRUE FALSE TRUE TRUE FALSE FALSE FALSE TRUE FALSE LIC022 Message License Manager database locked due to ongoing backup and restore operation.
PAGE 350
Trap/EventID 8515 LCD Message No LCD message display defined. Initial Default. SNMP Alert;#EMAIL Alert;#LC Log;#Remote System Log Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset TRUE FALSE TRUE TRUE FALSE FALSE FALSE TRUE FALSE LIC213 Message A system error was detected during License Manager startup. Detailed Description This error can occur when: 1) License Manager fails to load due to lack of system resources.
PAGE 351
Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE LIC901 Invalid parameter value forarg1. Message Arguments • arg1 = parameter Detailed Description The value provided for the specified parameter is invalid. Recommended Response Action To provide the correct value for the specified parameter, see Lifecycle Controller-Remote Services documentation.
PAGE 352
Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE LIC903 Missing parametersarg1. Message Arguments • arg1 = parameters Detailed Description One or more parameters were not specified for the invoked method. Recommended Response Action To provide the correct parameters, see Lifecycle Controller-Remote Services documentation.
PAGE 353
Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE LIC905 Message The LicenseName value cannot exceed 64 characters. Detailed Description The LicenseName value is greater than the allowed max length of 64. Recommended Response Action Correct the length of the LicenseName value and retry the operation.
PAGE 354
LIC907 Message Unable to perform the operation due to an unknown error in iDRAC. Detailed Description The operation failed to execute due to an unknown error in iDRAC. Recommended Response Action Retry the operation. If this fails, reset iDRAC. Category Configuration SubCategory LIC = Licensing Severity Severity 2 (Warning) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default.
PAGE 355
20 LNK Event Messages LNK8500 Network link to servers in slotarg1IOMarg2portarg3is down Message Arguments • • • arg1 = slot id arg2 = iom id arg3 = port id Detailed Description Internal sled network connection is down Recommended Response Action Remove and re-insert the sled Category System Health SubCategory LNK = Link Status Severity Severity 1 (Critical) Trap/EventID 2249 LCD Message No LCD message display defined. Initial Default.
PAGE 356
Category System Health SubCategory LNK = Link Status Severity Severity 3 (Informational) Trap/EventID 2251 LCD Message No LCD message display defined. Initial Default. SNMP Alert;#EMAIL Alert;#LCD;#LC Log;#Remote System Log Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset TRUE FALSE TRUE TRUE TRUE FALSE FALSE FALSE TRUE LNK2700 Thearg1network link is down.
PAGE 357
Recommended Response Action No response action is required. Category System Health SubCategory LNK = Link Status Severity Severity 3 (Informational) Trap/EventID 2251 LCD Message No LCD message display defined. Initial Default.
PAGE 358
PAGE 359
21 LOG Event Messages LOG004 Message Resource allocation failure. Detailed Description The operation failed due to lack of memory or file space in iDRAC. Recommended Response Action Reset iDRAC and retry the operation. Category Configuration SubCategory LOG = Log event Severity Severity 1 (Critical) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default.
PAGE 360
Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE LOG300 Message The system recovered from Chassis Log file corruption. Detailed Description The system recovered from Chassis Log file corruption. Some log entries may not be recovered. Recommended Response Action No response action is required.
PAGE 361
LOG303 Message Unable to archive the Chassis Log file. Detailed Description Unable to rename current Chassis Log file during archive operation. Some log entries may be lost. Recommended Response Action No response action is required. Category Configuration SubCategory LOG = Log event Severity Severity 3 (Informational) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default.
PAGE 362
Arguments • arg1 = log entry count Detailed Description This message is generated after a series of sequential duplicate events. Log entry count is the number of times the previous message was repeated. Recommended Response Action No response action is required. Category Audit SubCategory LOG = Log event Severity Severity 3 (Informational) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default.
PAGE 363
22 MEM Event Messages MEM8500 Message Low memory condition detected. Detailed Description A low memory condition was detected. If this condition continues, a failover or a reset may occur. If multiple resets occur, contact your service provider. Recommended Response Action If multiple resets occur, contact Service. Category Audit SubCategory MEM = Memory Severity Severity 1 (Critical) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default.
PAGE 364
LCD Message No LCD message display defined. Initial Default. LC Log Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE TRUE FALSE FALSE FALSE FALSE FALSE MEM8502 Message ECC Memory error rate failover condition detected. Detailed Description An ECC memory condition was detected on the primary CMC and a failover was initiated. Recommended Response Action Reseat the primary CMC and initiate a failover back to the primary CMC.
PAGE 365
Initial Default. FALSE Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE MEM0016 Memory device at location(s)arg1is operating correctly. Message Arguments • arg1 = location Detailed Description None Recommended Response Action No response action is required.
PAGE 366
LCD Message Multi-bit memory error on . Reseat memory Initial Default. FALSE Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE MEM0002 Parity memory errors detected on a memory device at locationarg1. Message Arguments • arg1 = location Detailed Description The memory is operational. This is an early indicator of a possible future uncorrectable error.
PAGE 367
Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default. FALSE Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE MEM0004 Memory device at locationarg1is disabled. Message Arguments • arg1 = location Detailed Description The memory may not be seated correctly, misconfigured, or has failed. Memory size is reduced.
PAGE 368
Severity Severity 3 (Informational) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default. FALSE Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE MEM0005 Persistent correctable memory error limit reached for a memory device at location(s)arg1. Message Arguments • arg1 = location Detailed Description The memory is operational.
PAGE 369
SubCategory MEM = Memory Severity Severity 3 (Informational) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default. FALSE Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE MEM0006 Memory device at locationarg1is present. Message Arguments • arg1 = location Detailed Description None Recommended Response Action No response action is required.
PAGE 370
Category System Health SubCategory MEM = Memory Severity Severity 2 (Warning) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default. FALSE Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE MEM0007 Unsupported memory configuration; check memory device at locationarg1.
PAGE 371
Recommended Response Action No response action is required. Category System Health SubCategory MEM = Memory Severity Severity 3 (Informational) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default. FALSE Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE MEM0024 Memory device at locationarg1is no longer spare memory.
PAGE 372
Detailed Description System performance is degraded. Recommended Response Action If unexpected, review system logs for power or thermal exceptions. Category System Health SubCategory MEM = Memory Severity Severity 2 (Warning) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default.
PAGE 373
Detailed Description None Recommended Response Action No response action is required. Category System Health SubCategory MEM = Memory Severity Severity 3 (Informational) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default. FALSE Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE MEM1201 Memory RAID redundancy is lost. Check memory device at location(s)arg1.
PAGE 374
Detailed Description None Recommended Response Action Re-install the memory component. If the problem continues, contact support. Category System Health SubCategory MEM = Memory Severity Severity 2 (Warning) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default. FALSE Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE MEM1203 Message Memory is not redundant.
PAGE 375
Category System Health SubCategory MEM = Memory Severity Severity 3 (Informational) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default. FALSE Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE MEM1205 Memory mirror redundancy is lost. Check memory device at location(s)arg1.
PAGE 376
Recommended Response Action Review system logs for memory exceptions. Re-install memory at location Category System Health SubCategory MEM = Memory Severity Severity 2 (Warning) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default. FALSE Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE MEM1207 Message Memory spare is redundant.
PAGE 377
Recommended Response Action Review system logs for memory exceptions. Re-install memory at location Category System Health SubCategory MEM = Memory Severity Severity 1 (Critical) Trap/EventID FALSE LCD Message Memory spared lost on . Power cycle system Initial Default.
PAGE 378
Detailed Description None Recommended Response Action No response action is required. Category System Health SubCategory MEM = Memory Severity Severity 3 (Informational) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default. FALSE Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE MEM0701 Correctable memory error rate exceeded forarg1.
PAGE 379
Detailed Description The memory may not be operational. This an early indicator of a possible future uncorrectable error. Recommended Response Action Re-install the memory component. If the problem continues, contact support. Category System Health SubCategory MEM = Memory Severity Severity 1 (Critical) Trap/EventID FALSE LCD Message Correctable memory error rate exceeded for . Reseat memory. Initial Default.
PAGE 380
Detailed Description None Recommended Response Action No response action is required. Category System Health SubCategory MEM = Memory Severity Severity 3 (Informational) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default. FALSE Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE MEM7000 Message The memory riser mismatch was corrected.
PAGE 381
Category System Health SubCategory MEM = Memory Severity Severity 1 (Critical) Trap/EventID FALSE LCD Message Memory riser mismatch detected. Check memory riser Initial Default. FALSE Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE MEM0600 Memory device was added at locationarg1.
PAGE 382
Recommended Response Action No response action is required. Category System Health SubCategory MEM = Memory Severity Severity 3 (Informational) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default. FALSE Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE MEM1210 Message Memory is redundant.
PAGE 383
SubCategory MEM = Memory Severity Severity 1 (Critical) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default. FALSE Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE MEM1214 Message Memory redundancy is degraded. Detailed Description The memory may not be seated correctly, misconfigured, or has failed.
PAGE 384
Severity Severity 3 (Informational) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default. FALSE Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE MEM1001 Memory device at locationarg1failed to transition to a running state. Message Arguments • arg1 = location Detailed Description None Recommended Response Action Re-install the memory component.
PAGE 385
SubCategory MEM = Memory Severity Severity 3 (Informational) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default. FALSE Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE MEM1003 Memory device at locationarg1failed to transition to in test.
PAGE 386
Category System Health SubCategory MEM = Memory Severity Severity 3 (Informational) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default. FALSE Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE MEM1005 Memory device at locationarg1failed to power off.
PAGE 387
Recommended Response Action No response action is required. Category System Health SubCategory MEM = Memory Severity Severity 3 (Informational) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default. FALSE Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE MEM1007 Memory device at locationarg1failed to transition to online.
PAGE 388
Detailed Description None Recommended Response Action No response action is required. Category System Health SubCategory MEM = Memory Severity Severity 3 (Informational) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default. FALSE Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE MEM1009 Memory device at locationarg1failed to transition to offline.
PAGE 389
Detailed Description None Recommended Response Action No response action is required. Category System Health SubCategory MEM = Memory Severity Severity 3 (Informational) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default. FALSE Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE MEM1011 Memory device at locationarg1is on-duty.
PAGE 390
Detailed Description None Recommended Response Action Re-install the memory component. If the problem continues, contact support. Category System Health SubCategory MEM = Memory Severity Severity 2 (Warning) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default.
PAGE 391
Detailed Description None Recommended Response Action No response action is required. Category System Health SubCategory MEM = Memory Severity Severity 3 (Informational) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default. FALSE Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE MEM1015 Memory device at locationarg1is in a power active state.
PAGE 392
Detailed Description The memory may not be seated correctly, misconfigured, or has failed. Memory size is reduced. Recommended Response Action Re-install the memory component. If the problem continues, contact support. Category System Health SubCategory MEM = Memory Severity Severity 1 (Critical) Trap/EventID FALSE LCD Message Memory is not installed correctly. Re-install Initial Default.
PAGE 393
23 OSE Event Messages OSE0000 Message A critical stop occurred during OS load. Detailed Description The system halted due to an exception during operating system load or operating system initialization. Recommended Response Action Review operating system logs and system video for additional information Category System Health SubCategory OSE = OS Event Severity Severity 1 (Critical) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default.
PAGE 394
Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE OSE0002 Message An OS graceful stop occurred. Detailed Description (IPMI sensor type 20h - offset 02h). Recommended Response Action No response action is required. Category System Health SubCategory OSE = OS Event Severity Severity 3 (Informational) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default.
PAGE 395
OSE0004 Message A soft shut-down initiated by platform event filter. Detailed Description A separate exception or status condition shutdown the operating system. (IPMI sensor type 20h - offset 04h). Recommended Response Action Review system event log for platform events capable of shutting the system down. Category System Health SubCategory OSE = OS Event Severity Severity 1 (Critical) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default.
PAGE 396
Detailed Description The system OS has successfully booted from A: Recommended Response Action No response action is required. Category System Health SubCategory OSE = OS Event Severity Severity 3 (Informational) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default.
PAGE 397
Category System Health SubCategory OSE = OS Event Severity Severity 3 (Informational) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default. FALSE Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE OSE1003 Message Failed to boot from C. Detailed Description None Recommended Response Action Review system boot configuration and boot media.
PAGE 398
Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default. FALSE Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE OSE1005 Message PXE boot failed.
PAGE 399
Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE OSE1007 Message Diagnostic boot failed. Detailed Description None Recommended Response Action Review system boot configuration and boot media. See system video for additional information Category System Health SubCategory OSE = OS Event Severity Severity 1 (Critical) Trap/EventID FALSE LCD Message No LCD message display defined.
PAGE 400
OSE1009 Message Failed to boot from CD-ROM. Detailed Description None Recommended Response Action Review system boot configuration and boot media. Verify the media in the CDROM is bootable. See system video for additional information Category System Health SubCategory OSE = OS Event Severity Severity 1 (Critical) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default.
PAGE 401
Detailed Description None Recommended Response Action Check system event logs for additional exception information. Power down the system and attempt to boot again. Category System Health SubCategory OSE = OS Event Severity Severity 1 (Critical) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default.
PAGE 402
Category System Health SubCategory OSE = OS Event Severity Severity 1 (Critical) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default.
PAGE 403
24 PCI Event Messages PCI1300 Message A front panel diagnostic interrupt was detected. Detailed Description The front panel diagnostic was pressed, and the system may be halted as a result. The interrupt was user induced. Recommended Response Action Reset the system to continue operation. Category System Health SubCategory PCI = PCI Device Severity Severity 1 (Critical) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default.
PAGE 404
Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default. FALSE Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE PCI1304 Message An I/O channel check error was detected. Detailed Description None Recommended Response Action Cycle input power, update component drivers, if device is removable, re-install the device.
PAGE 405
Severity Severity 1 (Critical) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default. FALSE Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE PCI1308 A PCI parity error was detected on a component at busarg1devicearg2functionarg3.
PAGE 406
Recommended Response Action Cycle input power, update component drivers, if device is removable, re-install the device. Category System Health SubCategory PCI = PCI Device Severity Severity 1 (Critical) Trap/EventID FALSE LCD Message PCI system error on bus device function . Power cycle system. Initial Default.
PAGE 407
Detailed Description System performance may be degraded. Recommended Response Action Cycle input power, update component drivers, if device is removable re-install the device at the next scheduled service time. Category System Health SubCategory PCI = PCI Device Severity Severity 1 (Critical) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default.
PAGE 408
PCI1318 A fatal error was detected on a component at busarg1devicearg2functionarg3. Message Arguments • • • arg1 = bus arg2 = device arg3 = func Detailed Description System performance may be degraded, or system may fail to operate. Recommended Response Action Cycle input power, update component drivers, if device is removable, re-install the device.
PAGE 409
Initial Default. FALSE Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE PCI1342 A bus time-out was detected on a component at slotarg1. Message Arguments • arg1 = number Detailed Description System performance may be degraded. The device has failed to respond to a transaction (master/target abort or completion timeout).
PAGE 410
Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE PCI1346 A software error was detected on a component at slotarg1. Message Arguments • arg1 = number Detailed Description None Recommended Response Action Reboot the system and update the component drivers.
PAGE 411
Initial Default. FALSE Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE PCI1350 A PCI system error was detected on a component at slotarg1. Message Arguments • arg1 = number Detailed Description System performance may be degraded, or system may fail to operate. Recommended Response Action Cycle input power, update component drivers, if device is removable, re-install the device.
PAGE 412
LCD Message No LCD message display defined. Initial Default. FALSE Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE PCI1356 A bus uncorrectable error was detected on a component at slotarg1. Message Arguments • arg1 = number Detailed Description System performance may be degraded, or system may fail to operate.
PAGE 413
Trap/EventID FALSE LCD Message Fatal error on slot . Reseat PCI card Initial Default. FALSE Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE PCI1360 A bus fatal error was detected on a component at slotarg1. Message Arguments • arg1 = number Detailed Description System performance may be degraded, or system may fail to operate.
PAGE 414
SubCategory PCI = PCI Device Severity Severity 2 (Warning) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default. FALSE Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE PCI1362 Bus performance degraded for a component at slotarg1. Message Arguments • arg1 = number Detailed Description System performance may be degraded.
PAGE 415
Recommended Response Action Cycle input power, update component drivers, remove and re-install the device. Category System Health SubCategory PCI = PCI Device Severity Severity 1 (Critical) Trap/EventID FALSE LCD Message Fatal IO error on bus device function . Contact support Initial Default.
PAGE 416
Detailed Description System performance may be degraded, or system may fail to operate. Recommended Response Action Cycle input power, update component drivers, remove and re-install the device. Category System Health SubCategory PCI = PCI Device Severity Severity 1 (Critical) Trap/EventID FALSE LCD Message Fatal IO error on slot . Contact support Initial Default.
PAGE 417
Detailed Description Either the BIOS, BMC/iDRAC, or LOM firmware is out of date and does not support FlexAddress. Recommended Response Action Update BIOS, BMC/iDRAC, and LOM firmware. If problem persists please contact customer support. Category System Health SubCategory PCI = PCI Device Severity Severity 1 (Critical) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default.
PAGE 418
Detailed Description Either the BIOS, BMC/iDRAC, LOM, or NIC firmware is out of date and does not support FlexAddress. Recommended Response Action Update BIOS, BMC/iDRAC, LOM, and mezzanine card firmware. If problem persists please contact customer support. Category System Health SubCategory PCI = PCI Device Severity Severity 1 (Critical) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default.
PAGE 419
PCI3004 Device option ROM on mezzanine cardarg1failed to support Link Tuning or FlexAddress. Message Arguments • arg1 = number Detailed Description Either the BIOS, BMC/iDRAC, or mezzanine card firmware is out of date and does not support FlexAddress. Recommended Response Action Update BIOS, BMC/iDRAC, and mezzanine card firmware. If problem persists please contact customer support.
PAGE 420
Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE PCI3006 Message Failed to get Link Tuning or FlexAddress data from iDRAC. Detailed Description Either the BIOS or BMC/iDRAC firmware is out of date and does not support FlexAddress. Recommended Response Action Update BIOS, and BMC/iDRAC firmware. If problem persists please contact customer support.
PAGE 421
PCI3008 A non-fatal PCIe error detected on a component at busarg1devicearg2functionarg3. Message Arguments • • • arg1 = bus arg2 = device arg3 = func Detailed Description System performance may be degraded. Recommended Response Action Cycle input power, update component drivers, remove and re-install the device at the next service window. Category System Health SubCategory PCI = PCI Device Severity Severity 2 (Warning) Trap/EventID FALSE LCD Message No LCD message display defined.
PAGE 422
Initial Default. FALSE Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE PCI3010 A non-fatal IO error detected on a component at busarg1devicearg2functionarg3. Message Arguments • • • arg1 = bus arg2 = device arg3 = func Detailed Description System performance may be degraded.
PAGE 423
SubCategory PCI = PCI Device Severity Severity 3 (Informational) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default. FALSE Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE PCI3012 Message The QuickPath Interconnect (QPI) width degraded. Detailed Description System performance may be degraded. The bus is not operating at maximum speed or width.
PAGE 424
LCD Message No LCD message display defined. Initial Default. FALSE Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE PCI3014 A non-fatal PCIe error detected on a component at slotarg1. Message Arguments • arg1 = number Detailed Description System performance may be degraded.
PAGE 425
Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default. FALSE Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE PCI3016 Message Device option ROM on mezzanine card failed to support Link Tuning or FlexAddress. Detailed Description Either the BIOS, BMC/iDRAC, or mezzanine card firmware is out of date and does not support FlexAddress.
PAGE 426
Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE FALSE FALSE FALSE FALSE 426 FALSE FALSE
PAGE 427
25 PDR Event Messages PDR1 arg1copyback stopped for rebuild. Message Arguments • arg1 = physical disk Detailed Description This message is generated after a copyback stops on a physical disk during a rebuild operation. Recommended Response Action Wait for rebuild to finish, then copyback should resume. Category Storage SubCategory PDR = Physical Disk Severity Severity 2 (Warning) Trap/EventID 4346 LCD Message No LCD message display defined. Initial Default.
PAGE 428
Trap/EventID 4346 LCD Message No LCD message display defined. Initial Default. SNMP Alert;#LCD;#Remote System Log Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset TRUE FALSE TRUE TRUE TRUE FALSE FALSE TRUE FALSE PDR3 arg1is not functioning correctly. Message Arguments • arg1 = PD Name Detailed Description The RAID Controller may not be able to read/write data to the physical disk drive indicated in the message.
PAGE 429
SubCategory PDR = Physical Disk Severity Severity 3 (Informational) Trap/EventID 4347 LCD Message No LCD message display defined. Initial Default. SNMP Alert;#LCD;#Remote System Log Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset TRUE FALSE TRUE TRUE TRUE FALSE FALSE TRUE FALSE PDR5 arg1is removed. Message Arguments • arg1 = PD Name Detailed Description A physical disk has been removed from the disk group.
PAGE 430
Detailed Description A physical disk in the virtual disk is offline. This may have been user initiated. Recommended Response Action Force the physical disk online or assign a hot spare to the virtual disk. Category Storage SubCategory PDR = Physical Disk Severity Severity 2 (Warning) Trap/EventID 4346 LCD Message No LCD message display defined. Initial Default.
PAGE 431
Detailed Description This alert is provided for informational purposes. Recommended Response Action No response action is required. Category Storage SubCategory PDR = Physical Disk Severity Severity 3 (Informational) Trap/EventID 4347 LCD Message No LCD message display defined. Initial Default.
PAGE 432
Detailed Description This message is generated after a rebuild starts on a physical disk. Recommended Response Action No response action is required. Category Storage SubCategory PDR = Physical Disk Severity Severity 3 (Informational) Trap/EventID 4347 LCD Message No LCD message display defined. Initial Default.
PAGE 433
Detailed Description The physical disk has failed or is corrupt. Recommended Response Action Replace the failed or corrupt disk. Identify a disk that has failed by locating the disk that has a red "X" for its status. Restart the initialization. Category Storage SubCategory PDR = Physical Disk Severity Severity 1 (Critical) Trap/EventID 4345 LCD Message No LCD message display defined. Initial Default.
PAGE 434
Detailed Description This alert is provided for informational purposes. Recommended Response Action No response action is required. Category Storage SubCategory PDR = Physical Disk Severity Severity 3 (Informational) Trap/EventID 4347 LCD Message No LCD message display defined. Initial Default.
PAGE 435
Detailed Description The physical disk is predicted to fail. Many physical disks contain Self Monitoring Analysis and Reporting Technology (SMART). When enabled, SMART monitors the disk health based on indications such as the number of write operations that were performed on the disk. Recommended Response Action Replace the physical disk. Even though the disk may not have failed yet, it is strongly recommended that the disk be replaced. Review other messages for additional information.
PAGE 436
Arguments • arg1 = PD Name Detailed Description A physical disk assigned as a hot spare was unassigned and is no longer functioning as a hot spare. The physical disk was unassigned by a user or automatically unassigned by Storage Management. Storage Management unassigns hot spares were used to rebuild data. Once the data is rebuilt onto the hot spare, the hot spare becomes a member of the virtual disk and is no longer assigned as a hot spare.
PAGE 437
Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset TRUE FALSE TRUE TRUE TRUE FALSE FALSE TRUE FALSE PDR20 SMART configuration change forarg1. Message Arguments • arg1 = PD Name Detailed Description A disk has received a SMART alert (predictive failure) after a configuration change. The disk is likely to fail in the near future. Recommended Response Action Replace the disk that has received the SMART alert.
PAGE 438
Trap/EventID 4346 LCD Message No LCD message display defined. Initial Default. SNMP Alert;#LCD;#Remote System Log Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset TRUE FALSE TRUE TRUE TRUE FALSE FALSE TRUE FALSE PDR22 SMART warning temperature forarg1 Message Arguments • arg1 = PD Name Detailed Description A disk has reached an unacceptable temperature and received a SMART alert (predictive failure).
PAGE 439
Detailed Description A disk is degraded and has received a SMART alert (predictive failure). The disk is likely to fail in the near future. Recommended Response Action Replace the disk that has received the SMART alert. If the physical disk is a member of a nonredundant virtual disk, then back up the data before replacing the disk. Removing a physical disk that is included in a non-redundant virtual disk will cause the virtual disk to fail and may cause data loss.
PAGE 440
Arguments • arg1 = PD Name Detailed Description Portions of the physical disk that were formerly inaccessible have been recovered. This alert is provided for informational purposes. Recommended Response Action No response action is required. Category Storage SubCategory PDR = Physical Disk Severity Severity 3 (Informational) Trap/EventID 4347 LCD Message No LCD message display defined. Initial Default.
PAGE 441
PDR27 Dedicated hot spare assigned toarg1. Message Arguments • arg1 = PD Name Detailed Description A user assigned a physical disk as a dedicated hot spare to a virtual disk. See Protecting Your Virtual Disk with a Hot Spare for more information. This alert is provided for informational purposes. Recommended Response Action No response action is required.
PAGE 442
LCD Message No LCD message display defined. Initial Default. SNMP Alert;#LCD;#Remote System Log Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset TRUE FALSE TRUE TRUE TRUE FALSE FALSE FALSE TRUE PDR29 Rebuild onarg1completed with error(s). Message Arguments • arg1 = PD Name Detailed Description See A Rebuild Completes with Errors for more information. Recommended Response Action See A Rebuild Completes with Errors for more information.
PAGE 443
Severity Severity 2 (Warning) Trap/EventID 4346 LCD Message No LCD message display defined. Initial Default. SNMP Alert;#LCD;#Remote System Log Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset TRUE FALSE TRUE TRUE TRUE FALSE FALSE TRUE FALSE PDR31 A global hot spare has been removed.arg1 Message Arguments • arg1 = PD Name Detailed Description The controller cannot to communicate with a disk that is assigned as a global hot spare.
PAGE 444
Category Storage SubCategory PDR = Physical Disk Severity Severity 2 (Warning) Trap/EventID 4346 LCD Message No LCD message display defined. Initial Default. SNMP Alert;#LCD;#Remote System Log Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset TRUE FALSE TRUE TRUE TRUE FALSE FALSE TRUE FALSE PDR33 A dedicated hot spare has been removed.
PAGE 445
Recommended Response Action No response action is required. Category Storage SubCategory PDR = Physical Disk Severity Severity 3 (Informational) Trap/EventID 4347 LCD Message No LCD message display defined. Initial Default. SNMP Alert;#LCD;#Remote System Log Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset TRUE FALSE TRUE TRUE TRUE FALSE FALSE TRUE FALSE PDR35 The only hot spare available is a SATA diskarg1.
PAGE 446
Detailed Description The only physical disk available to be assigned as a hot spare is using SAS technology. The physical disks in the virtual disk are using SATA technology. Because of this difference in technology, the hot spare cannot rebuild data if one of the physical disks in the virtual disk fails. Recommended Response Action Add a SATA disk that is large enough to be used as the hot spare and assign the new disk as a hot spare.
PAGE 447
Arguments • arg1 = physical disk Detailed Description A user has initiated a clear operation on a physical disk. Recommended Response Action No response action is required. Category Storage SubCategory PDR = Physical Disk Severity Severity 3 (Informational) Trap/EventID 4347 LCD Message No LCD message display defined. Initial Default.
PAGE 448
PDR40 The blink operation has ceased onarg1. Message Arguments • arg1 = physical disk Detailed Description This alert is provided for informational purposes. Recommended Response Action No response action is required. Category Storage SubCategory PDR = Physical Disk Severity Severity 3 (Informational) Trap/EventID 4347 LCD Message No LCD message display defined. Initial Default.
PAGE 449
Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset TRUE FALSE TRUE TRUE TRUE FALSE FALSE FALSE TRUE PDR42 arg1has been started. Message Arguments • arg1 = physical disk Detailed Description This alert is provided for informational purposes. Recommended Response Action No response action is required.
PAGE 450
Initial Default. SNMP Alert;#LCD;#Remote System Log Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset TRUE FALSE TRUE TRUE TRUE FALSE FALSE TRUE FALSE PDR44 The clear operation onarg1failed. Message Arguments • arg1 = physical disk Detailed Description A Clear task was being performed on a physical disk but the task was interrupted and did not complete successfully.
PAGE 451
Trap/EventID 4345 LCD Message No LCD message display defined. Initial Default. SNMP Alert;#LCD;#Remote System Log Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset TRUE FALSE TRUE TRUE TRUE FALSE FALSE TRUE FALSE PDR47 A block onarg1was punctured by the controller.
PAGE 452
Category Storage SubCategory PDR = Physical Disk Severity Severity 3 (Informational) Trap/EventID 4347 LCD Message No LCD message display defined. Initial Default. SNMP Alert;#LCD;#Remote System Log Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset TRUE FALSE TRUE TRUE TRUE FALSE FALSE TRUE FALSE PDR49 The dedicated hot sparearg1is too small.
PAGE 453
Recommended Response Action Assign a larger disk as the global hot spare. Category Storage SubCategory PDR = Physical Disk Severity Severity 2 (Warning) Trap/EventID 4346 LCD Message No LCD message display defined. Initial Default. SNMP Alert;#LCD;#Remote System Log Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset TRUE FALSE TRUE TRUE TRUE FALSE FALSE TRUE FALSE PDR51 Hot sparearg1SMART polling has failed.
PAGE 454
Recommended Response Action Make sure the cables are attached securely. See the Cables Attached Correctly section for more information on checking the cables. Make sure both Enclosure Management Modules (EMMs) are healthy. Category Storage SubCategory PDR = Physical Disk Severity Severity 2 (Warning) Trap/EventID 4346 LCD Message No LCD message display defined. Initial Default.
PAGE 455
Detailed Description This message is generated after a disk media error is corrected on a physical disk. Recommended Response Action No response action is required. Category Storage SubCategory PDR = Physical Disk Severity Severity 3 (Informational) Trap/EventID 4347 LCD Message No LCD message display defined. Initial Default.
PAGE 456
Detailed Description The bad block table is the table used for remapping bad disk blocks. This table fills as bad disk blocks are remapped. When the table is full, bad disk blocks are no longer remapped, which means that disk errors are no longer corrected. At this point, data loss can occur. The bad block table is now 80 percent full. Recommended Response Action Replace the disk generating this message.
PAGE 457
PDR58 arg1is incompatible. Message Arguments • arg1 = PD Name Detailed Description A user attempted to replace a disk with another disk that is using an incompatible technology. For example, replaced one side of a mirror with a SAS disk when the other side of the mirror is using SATA technology. Recommended Response Action Refer to the hardware documentation for information on replacing disks.
PAGE 458
Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset TRUE FALSE TRUE TRUE TRUE FALSE FALSE TRUE FALSE PDR60 Error occurred onarg1:arg2. Message Arguments • • arg1 = physical disk arg2 = error code Detailed Description The reason for the error can vary depending on the situation. The firmware error code is indicated in the message. Recommended Response Action Verify the health of attached devices. Review the Lifecycle log for significant events.
PAGE 459
LCD Message No LCD message display defined. Initial Default. SNMP Alert;#LCD;#Remote System Log Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset TRUE FALSE TRUE TRUE TRUE FALSE FALSE TRUE FALSE PDR62 The rebuild failed due to errors on the targetarg1. Message Arguments • arg1 = physical disk Detailed Description It is not possible to rebuild data that resides on a defective disk. Recommended Response Action Replace the target disk.
PAGE 460
Severity Severity 1 (Critical) Trap/EventID 4345 LCD Message No LCD message display defined. Initial Default. SNMP Alert;#LCD;#Remote System Log Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset TRUE FALSE TRUE TRUE TRUE FALSE FALSE TRUE FALSE PDR64 An unrecoverable disk media error occurred onarg1.
PAGE 461
SubCategory PDR = Physical Disk Severity Severity 3 (Informational) Trap/EventID 4347 LCD Message No LCD message display defined. Initial Default. SNMP Alert;#LCD;#Remote System Log Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset TRUE FALSE TRUE TRUE TRUE FALSE FALSE FALSE TRUE PDR66 arg1that was marked as missing has been replaced.
PAGE 462
Severity Severity 2 (Warning) Trap/EventID 4346 LCD Message No LCD message display defined. Initial Default. SNMP Alert;#LCD;#Remote System Log Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset TRUE FALSE TRUE TRUE TRUE FALSE FALSE TRUE FALSE PDR68 Dedicated sparearg1imported as global due to missing disk groups.
PAGE 463
SubCategory PDR = Physical Disk Severity Severity 2 (Warning) Trap/EventID 4346 LCD Message No LCD message display defined. Initial Default. SNMP Alert;#LCD;#Remote System Log Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset TRUE FALSE TRUE TRUE TRUE FALSE FALSE TRUE FALSE PDR70 Copyback started fromarg1toarg2.
PAGE 464
Recommended Response Action No response action is required. Category Storage SubCategory PDR = Physical Disk Severity Severity 3 (Informational) Trap/EventID 4347 LCD Message No LCD message display defined. Initial Default. SNMP Alert;#LCD;#Remote System Log Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset TRUE FALSE TRUE TRUE TRUE FALSE FALSE FALSE TRUE PDR72 Copyback resumed onarg1fromarg2.
PAGE 465
Detailed Description The physical disk participating in the copyback operation failed. Recommended Response Action Replace the disk and retry the operation. Category Storage SubCategory PDR = Physical Disk Severity Severity 1 (Critical) Trap/EventID 4345 LCD Message No LCD message display defined. Initial Default.
PAGE 466
Detailed Description This alert is provided for informational purposes Recommended Response Action No response action is required. Category Storage SubCategory PDR = Physical Disk Severity Severity 2 (Warning) Trap/EventID 4346 LCD Message No LCD message display defined. Initial Default.
PAGE 467
Detailed Description This alert is provided for informational purposes. Recommended Response Action No response action is required. Category Storage SubCategory PDR = Physical Disk Severity Severity 3 (Informational) Trap/EventID 4347 LCD Message No LCD message display defined. Initial Default.
PAGE 468
• arg2 = physical disk Detailed Description A user aborted an ongoing copyback operation. The operation did not complete. Recommended Response Action Re-issue the command. Category Storage SubCategory PDR = Physical Disk Severity Severity 3 (Informational) Trap/EventID 4347 LCD Message No LCD message display defined. Initial Default.
PAGE 469
Arguments • arg1 = physical disk Detailed Description Security on a secure encrypted disk was activated. Recommended Response Action No response action is required. Category Storage SubCategory PDR = Physical Disk Severity Severity 3 (Informational) Trap/EventID 4347 LCD Message No LCD message display defined. Initial Default.
PAGE 470
PDR84 arg1Security key has changed. Message Arguments • arg1 = physical disk Detailed Description The Security key on a secure encrypted disk was activated. Recommended Response Action No response action is required. Category Storage SubCategory PDR = Physical Disk Severity Severity 3 (Informational) Trap/EventID 4347 LCD Message No LCD message display defined. Initial Default.
PAGE 471
Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset TRUE FALSE TRUE TRUE TRUE FALSE FALSE TRUE FALSE PDR86 Bad block table onarg1is full. Message Arguments • arg1 = physical disk Detailed Description The number of blocks on the disk that exhibit an error has exceeded the capacity of the drive to remap. Any future writes to bad sectors will be unrecoverable. Recommended Response Action Replace the disk.
PAGE 472
Initial Default. SNMP Alert;#LCD;#Remote System Log Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset TRUE FALSE TRUE TRUE TRUE FALSE FALSE TRUE FALSE PDR88 Power state change failed onarg1. (fromarg2toarg3) Message Arguments • • • arg1 = PD Name arg2 = state arg3 = state Detailed Description When physical drives in spun down power state are configured, the drives should transition to spun up power state..
PAGE 473
Trap/EventID 4347 LCD Message No LCD message display defined. Initial Default. SNMP Alert;#LCD;#Remote System Log Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset TRUE FALSE TRUE TRUE TRUE FALSE FALSE TRUE FALSE PDR94 Microcode update onarg1has timed out. Message Arguments • arg1 = physical disk Detailed Description The attempt to update the physical disk has timed out.
PAGE 474
SubCategory PDR = Physical Disk Severity Severity 2 (Warning) Trap/EventID 4346 LCD Message No LCD message display defined. Initial Default. SNMP Alert;#LCD;#Remote System Log Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset TRUE FALSE TRUE TRUE TRUE FALSE FALSE FALSE TRUE PDR96 Security was disabled onarg1. Message Arguments • arg1 = physical disk Detailed Description Security on a secure encrypted disk was disabled.
PAGE 475
Category Storage SubCategory PDR = Physical Disk Severity Severity 3 (Informational) Trap/EventID 4347 LCD Message No LCD message display defined. Initial Default. SNMP Alert;#LCD;#Remote System Log Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset TRUE FALSE TRUE TRUE TRUE FALSE FALSE FALSE TRUE PDR98 Command timeout occurred onarg1.arg2.
PAGE 476
Recommended Response Action Verify that the disk is healthy and that it has not been removed. Check the cables. See the Cables Attached Correctly section for more information on checking the cables. If necessary, replace the disk and reassign the dedicated hot spare. Category Storage SubCategory PDR = Physical Disk Severity Severity 2 (Warning) Trap/EventID 4346 LCD Message No LCD message display defined. Initial Default.
PAGE 477
Detailed Description Internal Use Only. Recommended Response Action Internal Use Only. Category Storage SubCategory PDR = Physical Disk Severity Severity 2 (Warning) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default. LCD Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset TRUE FALSE FALSE FALSE TRUE FALSE FALSE FALSE FALSE PDR1100 Drivearg1is installed.
PAGE 478
Detailed Description The controller detected a drive removal Recommended Response Action If unintended, verify drive installation. Remove and reseat the indicated disk. If the problem persists, contact technical support. Refer to the product documentation to choose a convenient contact method. Category System Health SubCategory PDR = Physical Disk Severity Severity 1 (Critical) Trap/EventID FALSE LCD Message Drive is removed. Check drive Initial Default.
PAGE 479
Arguments • arg1 = number Detailed Description The controller received a SMART error from the drive. The drive is operational but needs replacement. Recommended Response Action The drive will need replacement at the next service window. Category System Health SubCategory PDR = Physical Disk Severity Severity 2 (Warning) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default.
PAGE 480
PDR1103 Drivearg1is the hot-spare drive. Message Arguments • arg1 = number Detailed Description None Recommended Response Action No response action is required. Category System Health SubCategory PDR = Physical Disk Severity Severity 2 (Warning) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default.
PAGE 481
Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE PDR1104 Consistency check is in progress for drivearg1. Message Arguments • arg1 = number Detailed Description None Recommended Response Action No response action is required. Category System Health SubCategory PDR = Physical Disk Severity Severity 2 (Warning) Trap/EventID FALSE LCD Message No LCD message display defined.
PAGE 482
Initial Default. FALSE Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE PDR1105 Drivearg1is in the critical array. Message Arguments • arg1 = number Detailed Description None Recommended Response Action No response action is required.
PAGE 483
LCD Message No LCD message display defined. Initial Default. FALSE Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE PDR1106 Drivearg1is in the failed array. Message Arguments • arg1 = number Detailed Description None Recommended Response Action No response action is required.
PAGE 484
Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default. FALSE Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE PDR1107 Rebuild is in progress for drivearg1. Message Arguments • arg1 = number Detailed Description None Recommended Response Action No response action is required.
PAGE 485
Severity Severity 3 (Informational) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default. FALSE Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE PDR1108 Rebuild was aborted for drivearg1. Message Arguments • arg1 = number Detailed Description None Recommended Response Action No response action is required.
PAGE 486
Category System Health SubCategory PDR = Physical Disk Severity Severity 3 (Informational) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default. FALSE Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE PDR1001 Fault detected on drivearg1in disk drive bayarg2.
PAGE 487
Detailed Description The controller detected that the drive was removed. Recommended Response Action Verify drive installation. Remove and reseat the failed drive. If the problem persists, contact technical support. Refer to the product documentation to choose a convenient contact method. Category System Health SubCategory PDR = Physical Disk Severity Severity 1 (Critical) Trap/EventID FALSE LCD Message Drive removed from disk drive bay . Check drive. Initial Default.
PAGE 488
Arguments • • arg1 = number arg2 = bay Detailed Description The controller received a SMART error from the drive. The drive is operational but needs replacement. Recommended Response Action The drive will need replacement at the next service window. Category System Health SubCategory PDR = Physical Disk Severity Severity 2 (Warning) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default.
PAGE 489
PDR1019 Drivearg1in disk drive bayarg2is no longer the hot-spare drive. Message Arguments • • arg1 = number arg2 = bay Detailed Description None Recommended Response Action No response action is required. Category System Health SubCategory PDR = Physical Disk Severity Severity 3 (Informational) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default.
PAGE 490
Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE PDR1020 Consistency check for drivearg1in disk drive bayarg2completed. Message Arguments • • arg1 = number arg2 = bay Detailed Description None Recommended Response Action No response action is required.
PAGE 491
LCD Message Drive in disk drive bay is in the critical array. Replace drive. Initial Default. FALSE Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE PDR1021 Drivearg1in disk drive bayarg2is no longer in the critical array. Message Arguments • • arg1 = number arg2 = bay Detailed Description None Recommended Response Action No response action is required.
PAGE 492
Severity Severity 1 (Critical) Trap/EventID FALSE LCD Message Drive in disk drive bay is in the failed array. Replace drive. Initial Default. FALSE Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE PDR1022 Drivearg1in disk drive bayarg2is no longer in the failed array.
PAGE 493
Category System Health SubCategory PDR = Physical Disk Severity Severity 3 (Informational) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default. FALSE Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE PDR1023 Rebuild completed for drivearg1in disk drive bayarg2.
PAGE 494
Detailed Description None Recommended Response Action No response action is required. Category System Health SubCategory PDR = Physical Disk Severity Severity 2 (Warning) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default. FALSE Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE PDR1024 Drive mismatch detected for drivearg1in disk drive bayarg2.
PAGE 495
Arguments • • arg1 = number arg2 = bay Detailed Description None Recommended Response Action No response action is required. Category System Health SubCategory PDR = Physical Disk Severity Severity 3 (Informational) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default.
PAGE 496
PAGE 497
26 PST Event Messages PST0128 Message No memory is detected. Detailed Description System BIOS was unable to detect memory in the system . This exception occurred early in system power on, thus the system may not display video (BIOS Post Exception 80). Recommended Response Action Inspect System Memory. Category System Health SubCategory PST = BIOS POST Severity Severity 1 (Critical) Trap/EventID FALSE LCD Message No memory is detected. Inspect memory devices Initial Default.
PAGE 498
Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE PST0130 Message Memory is configured, but not usable. Detailed Description During memory configuration system BIOS encountered device failures or speed configurations that resulted in unused memory. This exception occurred early in system power on, thus the system may not display video.
PAGE 499
Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE PST0132 Message CMOS failed. Detailed Description System BIOS detected a failure with CMOS memory during system POST. This exception occurred early in system power on, thus the system may not display video. (BIOS POST Exception Code 84) Recommended Response Action Check system event log for CMOS battery exceptions.
PAGE 500
Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE PST0134 Message Interrupt controller failed. Detailed Description System BIOS detected a failure with the interrupt controller during system POST. This exception occurred early in system power on, thus the system may not display video. (BIOS POST Exception code 86) Recommended Response Action Remove and reapply input power.
PAGE 501
Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE PST0136 Message Programmable interval timer error. Detailed Description System BIOS detected an failure with the programmable interval timer during POST. This exception occurred early in system power on, thus the system may not display video.(BIOS POST Exception code 88) Recommended Response Action Remove and reapply input power.
PAGE 502
PST0138 Message SuperIO failed. Detailed Description System BIOS detected a failure with the SIO. This exception occurred early in system power on, thus the system may not display video. (BIOS POST code exception code 8A) Recommended Response Action Remove and reapply input power. If the problem persists, contact technical support. Refer to the product documentation to choose a convenient contact method.
PAGE 503
Detailed Description System BIOS failed to initialize the system management interrupt. This exception occurred early in system power on, thus the system may not display video. (BIOS POST exception code 8C) Recommended Response Action Remove and reapply input power. If the problem persists, contact technical support. Refer to the product documentation to choose a convenient contact method.
PAGE 504
Recommended Response Action Compare system memory installation to supported system memory configurations. Reduce system configuration to minimum memory configuration. Category System Health SubCategory PST = BIOS POST Severity Severity 1 (Critical) Trap/EventID FALSE LCD Message Memory initialization error. Contact support Initial Default.
PAGE 505
Category System Health SubCategory PST = BIOS POST Severity Severity 1 (Critical) Trap/EventID FALSE LCD Message Shut-down test failed. Power cycle system Initial Default. FALSE Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE PST0193 Message BIOS POST memory test failed. Detailed Description System BIOS POST memory test failed.
PAGE 506
Trap/EventID FALSE LCD Message Remote access controller configuration failed. Check screen message Initial Default. FALSE Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE PST0195 Message CPU configuration failed. Detailed Description The current processor configuration is unsupported or encountered a fatal exception during POST. Check the processor configuration.
PAGE 507
Initial Default. FALSE Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE PST0254 Message General failure after video. Detailed Description System BIOS detected a functional or configuration issue during system POST. Check the system video screen for more information. The system event log may contain additional details.
PAGE 508
Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE FALSE FALSE FALSE FALSE 508 FALSE FALSE
PAGE 509
27 PSU Event Messages PSU8501 Unable to retrieve PSUarg1input voltage information. Message Arguments • arg1 = slot number Detailed Description Unable to retrieve input voltage information for the PSU specified in the message. Recommended Response Action Remove the PSU from the chassis, wait for two minutes, and reinsert it. If the issue persists, contact your service provider.
PAGE 510
Severity Severity 2 (Warning) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default. LC Log Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE TRUE FALSE FALSE FALSE FALSE FALSE PSU8503 The PSU in slotarg1detected 220 VAC input voltage and does not match chassis configuration.
PAGE 511
Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default. LC Log Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE TRUE FALSE FALSE FALSE FALSE FALSE PSU8505 Message Unable to set the chassis redundancy policy to AC Redundancy. Detailed Description Unable to set the chassis redundancy policy to AC Redundancy.
PAGE 512
LCD Message No LCD message display defined. Initial Default. LC Log Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE TRUE FALSE FALSE FALSE FALSE FALSE PSU8507 Insufficient power available because PSU in the slotarg1is not present.. Message Arguments • arg1 = slot number Detailed Description The PSU identified in the message has been disengaged or removed. Insifficient power is available.
PAGE 513
Severity Severity 2 (Warning) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default.
PAGE 514
Category Audit SubCategory PSU = Power Supply Severity Severity 3 (Informational) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default. LC Log Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE TRUE FALSE FALSE FALSE FALSE FALSE PSU8512 Unable to update the firmware for the PSU in slotarg1.
PAGE 515
Detailed Description Unable to update the PSU firmware due to PMBus communication errors. Recommended Response Action Retry the firmware update operation. If the problem persists, contact your service provider. Category Audit SubCategory PSU = Power Supply Severity Severity 2 (Warning) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default.
PAGE 516
Detailed Description Unable to set redundancy policy because PSU enumeration is in progress. The policy can be set after PSU enumeration is complete. Recommended Response Action Retry the operation after the PSU enumeration is complete. Category Audit SubCategory PSU = Power Supply Severity Severity 3 (Informational) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default.
PAGE 517
Detailed Description The operation to read the FRU data from the PSU indentified in the message did not complete successfully due to internal communication errors. Recommended Response Action Retry the operation. If the condition persists, contact your service provider. Category Audit SubCategory PSU = Power Supply Severity Severity 1 (Critical) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default.
PAGE 518
Recommended Response Action No response action is required. Category Audit SubCategory PSU = Power Supply Severity Severity 3 (Informational) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default. LC Log Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE TRUE FALSE FALSE FALSE FALSE FALSE PSU1000 Power supply cable has been removed fromarg1.
PAGE 519
Detailed Description The power supply is not providing any power. This may be because the power supply switch is in the off position or the power supply has failed. Recommended Response Action Check whether the power switch on the power supply unit is turned off or on. If it is turned off, turn it on. If the problem is not corrected, verify that the power cord is attached and functional. See the storage hardware documentation for more information.
PAGE 520
Detailed Description The enclosure detected that a power supply unit was removed and is no longer functioning in optimal condition. Recommended Response Action Re-insert the power supply unit into the enclosure. Re-connect the AC power cable and switch on the power supply unit. Contact technical support if the issue persists. Category Storage SubCategory PSU = Power Supply Severity Severity 1 (Critical) Trap/EventID 4233 LCD Message No LCD message display defined. Initial Default.
PAGE 521
Detailed Description The enclosure detected that a power supply unit has failed. Recommended Response Action Check for other messages related to the state of the power supply unit/enclosure. These may help determine the cause of this event. Contact technical support if the issue still persists. Category Storage SubCategory PSU = Power Supply Severity Severity 1 (Critical) Trap/EventID 4233 LCD Message No LCD message display defined. Initial Default.
PAGE 522
Detailed Description None Recommended Response Action No response action is required. Category System Health SubCategory PSU = Power Supply Severity Severity 3 (Informational) Trap/EventID 2187 LCD Message No LCD message display defined. Initial Default. LC Log Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset TRUE FALSE TRUE TRUE FALSE FALSE FALSE TRUE FALSE PSU0001 Power supplyarg1failed.
PAGE 523
Detailed Description None Recommended Response Action No response action is required. Category System Health SubCategory PSU = Power Supply Severity Severity 3 (Informational) Trap/EventID 2187 LCD Message No LCD message display defined. Initial Default. LC Log Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset TRUE FALSE TRUE TRUE FALSE FALSE FALSE TRUE FALSE PSU0002 A predictive failure detected on power supplyarg1.
PAGE 524
Arguments • arg1 = number Detailed Description The power supply is installed correctly but an input source is not connected or is not functional. Recommended Response Action Verify the input source is attached to the power supply. Verify the input power is within the operating requirements for the power supply. Category System Health SubCategory PSU = Power Supply Severity Severity 1 (Critical) Trap/EventID 2185 LCD Message Power input for PSU is lost.
PAGE 525
PSU0004 The power input for power supplyarg1is outside of range. Message Arguments • arg1 = number Detailed Description The operating requirements for the power supply may be found in product documentation or on the power supply itself. Recommended Response Action Verify the input source is attached to the power supply. Verify the input power is within the operating requirements for the power supply.
PAGE 526
Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset TRUE FALSE TRUE TRUE FALSE FALSE FALSE TRUE FALSE PSU0006 Power supplyarg1is incorrectly configured. Message Arguments • arg1 = number Detailed Description Power supplies should be of the same input type and power rating. Recommended Response Action Install matched power supplies and review product documentation for proper configuration.
PAGE 527
Initial Default. LC Log Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset TRUE FALSE TRUE TRUE FALSE FALSE FALSE TRUE FALSE PSU0007 Power supplyarg1is operating at 110 volts, and could cause a circuit breaker fault. Message Arguments • arg1 = number Detailed Description A power supply that is designed to operate at 220V, but is connected to a 110V power source requires additional current for operation.
PAGE 528
Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default. FALSE Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE PSU0031 Cannot communicate with power supplyarg1. Message Arguments • arg1 = number Detailed Description The power supply may operate, however power supply monitoring will be degraded. System performance may be degraded.
PAGE 529
Severity Severity 3 (Informational) Trap/EventID 2187 LCD Message No LCD message display defined. Initial Default. LC Log Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset TRUE FALSE TRUE TRUE FALSE FALSE FALSE TRUE FALSE PSU0033 The temperature for power supplyarg1is outside of range. Message Arguments • arg1 = number Detailed Description System performance may be degraded.
PAGE 530
Category System Health SubCategory PSU = Power Supply Severity Severity 1 (Critical) Trap/EventID 2185 LCD Message An under voltage fault detected on PSU . Check power source. Initial Default. LC Log Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset TRUE FALSE TRUE TRUE FALSE FALSE FALSE TRUE FALSE PSU0035 An over voltage fault detected on power supplyarg1.
PAGE 531
Recommended Response Action 1) Remove and re-install the power supply. 2) Check cables and subsystem components in the system for damage. 3) If the issue persists, contact technical support. Refer to the product documentation to choose a convenient contact method. Category System Health SubCategory PSU = Power Supply Severity Severity 1 (Critical) Trap/EventID 2185 LCD Message An over current fault detected on PSU . Check PSU. Initial Default.
PAGE 532
Detailed Description Power supplies should be of the same input type and power rating. Recommended Response Action Install matched power supplies and review product documentation for proper configuration. Category System Health SubCategory PSU = Power Supply Severity Severity 1 (Critical) Trap/EventID 2185 LCD Message PSU wattage mismatch; PSU = watts Initial Default.
PAGE 533
Detailed Description None Recommended Response Action No response action is required. Category System Health SubCategory PSU = Power Supply Severity Severity 3 (Informational) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default. FALSE Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE PSU0901 Power unitarg1is on.
PAGE 534
Detailed Description None Recommended Response Action No response action is required. Category System Health SubCategory PSU = Power Supply Severity Severity 3 (Informational) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default. FALSE Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE PSU0904 Could not power down 240VA on power unitarg1.
PAGE 535
Detailed Description In order to meet service requirements the supply must be shut down. Recommended Response Action Remove input power at the power supply. Category System Health SubCategory PSU = Power Supply Severity Severity 1 (Critical) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default.
PAGE 536
Detailed Description The power supply is installed correctly but an input source is not connected or is not functional. Recommended Response Action Verify the input source is attached to the power supply. Verify the input power is within the operating requirements for the power supply. Category System Health SubCategory PSU = Power Supply Severity Severity 1 (Critical) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default.
PAGE 537
Detailed Description The system did not respond correctly to a power down request. Recommended Response Action Disconnect Input Power Category System Health SubCategory PSU = Power Supply Severity Severity 1 (Critical) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default.
PAGE 538
Detailed Description Status from the power supply indicates a power supply exception occurred. The power supply will try to operate in a degraded state. System Performance and power redundancy may be degraded or lost. Recommended Response Action Check input power. Re-install the power supply. If problem persists contact support. Category System Health SubCategory PSU = Power Supply Severity Severity 1 (Critical) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default.
PAGE 539
Arguments • arg1 = number Detailed Description Status from the power supply indicates a power supply exception occurred. The power supply will try to operate. System Performance and power redundancy may be degraded or lost. Recommended Response Action Remove input power and re-install supply at the next service window. Category System Health SubCategory PSU = Power Supply Severity Severity 2 (Warning) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default.
PAGE 540
PSU0077 Power supplyarg1vendor type mismatch detected. Message Arguments • arg1 = number Detailed Description Power supplies should be of the same input type and power rating. Recommended Response Action Install matched power supplies and review product documentation for proper configuration. Category System Health SubCategory PSU = Power Supply Severity Severity 1 (Critical) Trap/EventID 2185 LCD Message No LCD message display defined. Initial Default.
PAGE 541
Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset TRUE FALSE TRUE TRUE FALSE FALSE FALSE TRUE FALSE PSU0080 Power supplyarg1voltage rating does not match the systems requirements. Message Arguments • arg1 = number Detailed Description The system does not support mixed voltage power supplies. Recommended Response Action Review product documentation, change power supply with correct voltage rating.
PAGE 542
Initial Default. LC Log Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset TRUE FALSE TRUE TRUE FALSE FALSE FALSE TRUE FALSE PSU0039 An under current fault detected on power supplyarg1. Message Arguments • arg1 = number Detailed Description Insufficient amount of current to keep power supply operating at a normal levels. Recommended Response Action 1) Remove and re-install the power supply input cord.
PAGE 543
Trap/EventID 2185 LCD Message Output under voltage fault detected on PSU . Initial Default. LC Log Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset TRUE FALSE TRUE TRUE FALSE FALSE FALSE TRUE FALSE PSU0041 An output over voltage fault detected on power supplyarg1. Message Arguments • arg1 = number Detailed Description none Recommended Response Action 1) Remove the power supply input cord and then remove power supply.
PAGE 544
SubCategory PSU = Power Supply Severity Severity 1 (Critical) Trap/EventID 2185 LCD Message Output over current fault detected on PSU . Check PSU. Initial Default. LC Log Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset TRUE FALSE TRUE TRUE FALSE FALSE FALSE TRUE FALSE PSU0043 An output under current fault detected on power supplyarg1.
PAGE 545
Recommended Response Action If problem persist, remove and re-install power supply. Category System Health SubCategory PSU = Power Supply Severity Severity 2 (Warning) Trap/EventID 2186 LCD Message No LCD message display defined. Initial Default. LC Log Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset TRUE FALSE TRUE TRUE FALSE FALSE FALSE FALSE TRUE PSU0045 Power supplyarg1status information successfully obtained.
PAGE 546
PAGE 547
28 PSUA Event Messages PSUA0016 Power supplyarg1is absent. Message Arguments • arg1 = number Detailed Description The supply has been removed or has failed. Recommended Response Action Install the power supply if needed. Category System Health SubCategory PSUA = PSU Absent Severity Severity 1 (Critical) Trap/EventID 2465 LCD Message PSU is absent. Check PSU Initial Default.
PAGE 548
PAGE 549
29 PWR Event Messages PWR8500 Chassis power state updated toarg1fromarg2. Message Arguments • • arg1 = new power state arg2 = old power state Detailed Description The chassis power state from the configuration database and the current state are different. The current chassis power state will be updated in the configuration database. This is to insure the chassis power state will be the same if the CMC is rebooted or a CMC failover occurs. Recommended Response Action No response action is required.
PAGE 550
Severity Severity 3 (Informational) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default. LC Log Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE TRUE FALSE FALSE FALSE FALSE FALSE PWR8503 The current value of System Input Power Cap (arg1AC) is less than the upper limit (arg2AC).
PAGE 551
SubCategory PWR = Power Usage Severity Severity 3 (Informational) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default. LC Log Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE TRUE FALSE FALSE FALSE FALSE FALSE PWR8505 Message The Dynamic Power Supply Engagement feature was not successfully enabled. Detailed Description The Dynamic Power Supply Engagement feature was not successfully enabled.
PAGE 552
SubCategory PWR = Power Usage Severity Severity 3 (Informational) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default. LC Log Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE TRUE FALSE FALSE FALSE FALSE FALSE PWR8507 System Input Power Cap changed fromarg1W AC toarg2W AC.
PAGE 553
Recommended Response Action No response action is required. Make sure there are enough PSUs to support redundancy at the specified power budget. Category Audit SubCategory PWR = Power Usage Severity Severity 2 (Warning) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default.
PAGE 554
Detailed Description Unable to set the chassis power indentified in the message. Recommended Response Action Retry the operation. If the issue persists, contact your service provider. Category Audit SubCategory PWR = Power Usage Severity Severity 2 (Warning) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default.
PAGE 555
Category Audit SubCategory PWR = Power Usage Severity Severity 1 (Critical) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default. LC Log Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE TRUE FALSE FALSE FALSE FALSE FALSE PWR8514 Message Unable to perform chassis power action due to insufficient privileges.
PAGE 556
Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default. LC Log Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE TRUE FALSE FALSE FALSE FALSE FALSE PWR8516 Message Unable to perform the chassis power action requested.. Detailed Description Unable to perform the chassis power action requested. Recommended Response Action Check the tracelog for more information.
PAGE 557
Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE TRUE FALSE FALSE FALSE FALSE FALSE PWR8518 Message Unable to perform the chassis power action because the chassis is already turned on. Detailed Description Unable to perform the chassis power action because the chassis is already turned on. Recommended Response Action No response action is required.
PAGE 558
PWR8520 Message Initiated the chassis reset operation. Detailed Description The chassis reset operation was initiated. Recommended Response Action No response action is required. Category Audit SubCategory PWR = Power Usage Severity Severity 3 (Informational) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default.
PAGE 559
Detailed Description The chassis power cycle operation was initiated. Recommended Response Action No response action is required. Category Audit SubCategory PWR = Power Usage Severity Severity 3 (Informational) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default.
PAGE 560
Category Audit SubCategory PWR = Power Usage Severity Severity 3 (Informational) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default. LC Log Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE TRUE FALSE FALSE FALSE FALSE FALSE PWR8525 Message 110VAC Operation acknowledged. Detailed Description 110VAC operation of PSUs is acknowledged.
PAGE 561
Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default. LC Log Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE TRUE FALSE FALSE FALSE FALSE FALSE PWR8527 Message Server slot power priorities changed - reallocating power. Detailed Description Server slot power priorites were changed. Power to servers is being reallocated. Recommended Response Action No response action is required.
PAGE 562
LCD Message No LCD message display defined. Initial Default. LC Log Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE TRUE FALSE FALSE FALSE FALSE FALSE PWR8529 Message Max Power Conservation Mode is enabled. Detailed Description The Max Power Conservation Mode is enabled. Recommended Response Action No response action is required.
PAGE 563
Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE TRUE FALSE FALSE FALSE FALSE FALSE PWR8531 Message Server Based Power Management Mode is enabled. Detailed Description Server Based Power Management Mode is enabled. Recommended Response Action No response action is required. Category Audit SubCategory PWR = Power Usage Severity Severity 3 (Informational) Trap/EventID FALSE LCD Message No LCD message display defined.
PAGE 564
PWR8533 Power cap changed fromarg1W AC toarg2W AC. Message Arguments • • arg1 = power value arg2 = power value Detailed Description Power cap seeting was changed. Recommended Response Action No response action is required. Category Audit SubCategory PWR = Power Usage Severity Severity 3 (Informational) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default.
PAGE 565
PWR8535 Message Unable to set Server Based Power Management Mode to disable. Detailed Description Unable to set Server Based Power Management Mode to disable. Recommended Response Action Retry the operation. If the issue persists, contact your service provider. Category Audit SubCategory PWR = Power Usage Severity Severity 2 (Warning) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default.
PAGE 566
Detailed Description Server Performance Over Power Redundancy is disabled. Recommended Response Action No response action is required. Category Audit SubCategory PWR = Power Usage Severity Severity 3 (Informational) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default.
PAGE 567
Category Audit SubCategory PWR = Power Usage Severity Severity 3 (Informational) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default.
PAGE 568
SubCategory PWR = Power Usage Severity Severity 3 (Informational) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default. LC Log Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE TRUE FALSE FALSE FALSE FALSE FALSE PWR8542 Message Chassis powerup operation completed. Detailed Description Chassis powerup operation completed. Recommended Response Action No response action is required.
PAGE 569
Recommended Response Action Turn on the server identified in the message. If the issue persists, contact your service provider. Category Audit SubCategory PWR = Power Usage Severity Severity 2 (Warning) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default.
PAGE 570
Arguments • arg1 = slot number Detailed Description Incorrect power inventory information reported by the iDRAC for the server identified in the message. Recommended Response Action Invalid power inventory information could be due to outdated iDRAC firmware or server BIOS firmware versions. Update the components to their latest versions. Category Audit SubCategory PWR = Power Usage Severity Severity 1 (Critical) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default.
PAGE 571
Detailed Description The chassis was already turned off, when the power off request was received. Recommended Response Action No response action is required. Category Audit SubCategory PWR = Power Usage Severity Severity 3 (Informational) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default.
PAGE 572
Category Audit SubCategory PWR = Power Usage Severity Severity 2 (Warning) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default. LC Log Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE TRUE FALSE FALSE FALSE FALSE FALSE PWR8550 Message Chassis shutdown completed. Detailed Description Chassis shutdown completed. Recommended Response Action No response action is required.
PAGE 573
SubCategory PWR = Power Usage Severity Severity 3 (Informational) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default. LC Log Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE TRUE FALSE FALSE FALSE FALSE FALSE PWR8552 Chassis Management Controller is unable to turn onarg1-arg2because of insufficient power.
PAGE 574
• arg3 = priority number Detailed Description This situation occurs if the iDRAC is found to be turned off after power allocation information is sent by the CMC or if the communications between the CMC and iDRAC is non functional. Recommended Response Action Perform a Virtual Reseat of the component identified in the message. Using the CMC Web UI, go to Chassis Overview > Troubleshooting > Reset Components, and then select slot for the component identified in the message and apply the Virtual Reseat.
PAGE 575
Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset TRUE FALSE TRUE TRUE FALSE FALSE FALSE TRUE FALSE PWR8556 Serverarg1was shutdown due to insufficient power. Message Arguments • arg1 = slot number Detailed Description The Server identified in the messate was shutdowrn due to insufficient power. Recommended Response Action No response action is required.
PAGE 576
Initial Default. LC Log Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE TRUE FALSE FALSE FALSE FALSE FALSE PWR8560 Unable to turn on I/O Modulearg1due to insufficient chassis power. Message Arguments • arg1 = IOM slot name Detailed Description Unable to turn on the I/O Module identified in the message due to insufficient chassis power.
PAGE 577
Severity Severity 1 (Critical) Trap/EventID 8417 LCD Message No LCD message display defined. Initial Default. SNMP Alert;#EMAIL Alert;#LC Log;#Remote System Log Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset TRUE FALSE TRUE TRUE FALSE FALSE FALSE TRUE FALSE PWR8562 Unable to power on the serverarg1before power on timer expired.
PAGE 578
Category Audit SubCategory PWR = Power Usage Severity Severity 1 (Critical) Trap/EventID 8417 LCD Message No LCD message display defined. Initial Default. SNMP Alert;#EMAIL Alert;#LC Log;#Remote System Log Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset TRUE FALSE TRUE TRUE FALSE FALSE FALSE TRUE FALSE PWR8564 Unable to turn on the Serverarg1because the power request exceeded the System Input Power Cap.
PAGE 579
Detailed Description The Chassis Management Controller is unable to communicate with the iDRAC service processor for the Server identified in the message and the Server could not be turned off. This situation may occur when iDRAC is rebooting. Recommended Response Action Do the following: 1) Wait for a few minutes for the iDRAC service processor to complete startup. 2) Retry the operation.
PAGE 580
PWR8567 Unable to turn off Serverarg1on a power cycle action. Message Arguments • arg1 = server number Detailed Description Unable to turn off the Server on a power cycle operation. This happens if the Server did not show a "power off" status change within the expected time. Recommended Response Action The Server could have taken more time to turn off than expected. If the Server is turned off, turn on to complete the power cycle. If the Server has not completed a power cycle, retry the operation.
PAGE 581
Initial Default. LC Log Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE TRUE FALSE FALSE FALSE FALSE FALSE PWR8569 Unable to power cycle the serverarg1because the server is off. Message Arguments • arg1 = slot number Detailed Description The requested power cycle operation cannot be performed when the server is not turned on. The server should be already turned on for the power cycle operation to be successful.
PAGE 582
Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default. LC Log Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE TRUE FALSE FALSE FALSE FALSE FALSE PWR8571 Unable to perform the power action requested for the serverarg1because another power action is in progress. Message Arguments • arg1 = server idr Detailed Description Another power action is in progress.
PAGE 583
SubCategory PWR = Power Usage Severity Severity 3 (Informational) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default. LC Log Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE TRUE FALSE FALSE FALSE FALSE FALSE PWR8573 Message The Chassis Management Controller is unable to communicate to the iDRAC, when trying to turn off the serverarg1.
PAGE 584
Recommended Response Action Wait for three minutes, and then retry the operation. If the issue persists, remove and reinsert the server and wait for the iDRAC to finish restarting before retying the operation. Category Audit SubCategory PWR = Power Usage Severity Severity 1 (Critical) Trap/EventID 8417 LCD Message No LCD message display defined. Initial Default.
PAGE 585
Detailed Description The Virtual Reseat initiated on the Sleeve identified in the message successfully turned off the Sleeve. However, the Sleeve did not turn on successfully. A Virtual Reseat is the same as removing and inserting a Sleeve. Recommended Response Action Retry the Virtual Reseat operation on the Sleeve identified in the message. If the issue persists, manually remove and reinsert the Sleeve in the chassis.
PAGE 586
Arguments • arg1 = slot number Detailed Description The Chassis Management Controller is unable to turn on the iDRAC because power required is less than available power. Recommended Response Action Make sure there is enough power supply to distribute power. Go to, the Chassis Overview > Power > Power Budget Status. In the Total Input Power Available For Allocation field, view the available power. To add more power, insert more PSUs or remove unused components from the chassis.
PAGE 587
PWR8580 Chassis Management Controller is unable to turn on server-arg1because the Chassis is not turned on. Message Arguments • arg1 = slot number Detailed Description The power on request for the server identified in the message was not successful because the Chassis is turned off. Recommended Response Action Turn on the Chassis, and then retry the operation.
PAGE 588
Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE TRUE FALSE FALSE FALSE FALSE FALSE PWR8582 Chassis Management Controller is unable to turn on server-arg1because Max Power Conservation Mode is enabled. Message Arguments • arg1 = slot number Detailed Description Unable to turn on the server identified in the message because the Max Power Conservation Mode (MPCM) is enabled.
PAGE 589
Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default. None Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE PWR8584 Chassis Management Controller is unable to turn on server-arg1because the power supply redundancy is lost and Performance Over Power Redundancy feature is disabled and the power required is less than the available power.
PAGE 590
Recommended Response Action No response action is required. Category Audit SubCategory PWR = Power Usage Severity Severity 3 (Informational) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default.
PAGE 591
Detailed Description The server cannot be turned on if the chassis enclosure is open. Recommended Response Action The chassis enclosure is open. Retry the operation after closing the enclosure. Category Audit SubCategory PWR = Power Usage Severity Severity 3 (Informational) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default.
PAGE 592
Arguments • arg1 = slot number Detailed Description The PCIe Mezzanine card in the slot B1 is absent. Without PCIe Mezzannine cards, the chassis PCIe cards will not be available for servers. Recommended Response Action Insert a PCIe Mezzanine card in slot B1. Category Audit SubCategory PWR = Power Usage Severity Severity 3 (Informational) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default.
PAGE 593
PWR8591 Message Servers are turned off to allocate power to the newly inserted hard disk drives. Detailed Description Before inserting hard disk drives, always make sure the Chassis has enough available power. Otherwise operating servers may be turned off. Recommended Response Action Make sure there is enough power supply to distribute power. Go to, the Chassis Overview > Power > Power Budget Status. In the Total Input Power Available For Allocation field, view the available power.
PAGE 594
PWR8593 Message Chassis Management Controller is unable to turn on or turn off the chassis because the chassis infrastructure component firmware update is in progress. Detailed Description The chassis power operation cannot be performed when a chassis infrastructure firmware update is in progress. Recommended Response Action Retry the operation after the chassis infrastructure component firmware update is complete.
PAGE 595
Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE PWR8595 Chassis Management Controller is unable to turn on serverarg1due to insufficient power for thearg2.
PAGE 596
Category Audit SubCategory PWR = Power Usage Severity Severity 2 (Warning) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default. None Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE PWR8597 Power Supplyarg1is not supported and was turned off.
PAGE 597
Recommended Response Action Remove PSU Category Audit SubCategory PWR = Power Usage Severity Severity 1 (Critical) Trap/EventID 8417 LCD Message No LCD message display defined. Initial Default. SNMP Alert;#LCD;#LC Log;#Remote System Log Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset TRUE FALSE TRUE TRUE TRUE FALSE FALSE TRUE FALSE PWR8599 Serverarg1is not compatible with the power supplies in the enclosure.
PAGE 598
Recommended Response Action Increase power cap. Category System Health SubCategory PWR = Power Usage Severity Severity 2 (Warning) Trap/EventID 2274 LCD Message No LCD message display defined. Initial Default.
PAGE 599
SubCategory PWR = Power Usage Severity Severity 2 (Warning) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default. None Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset TRUE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE PWR1000 Message The system performance restored. Detailed Description None Recommended Response Action No response action is required.
PAGE 600
LCD Message System performance degraded. Check PSUs and system configuration Initial Default. FALSE Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE PWR1002 Message The system performance degraded because of thermal protection. Detailed Description To avoid shutdown, system performance has been degraded.
PAGE 601
Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE PWR1004 Message The system performance degraded because power capacity has changed. Detailed Description To avoid shutdown, system performance has been degraded. Recommended Response Action if unintended, review system configuration changes and power policy.
PAGE 602
PWR1006 Message The system halted because system power exceeds capacity. Detailed Description The system may shutdown. Recommended Response Action Review system configuration, upgrade power supplies or reduce system power consumption. Category System Health SubCategory PWR = Power Usage Severity Severity 1 (Critical) Trap/EventID FALSE LCD Message System power exceeds capacity. System halted. Contact support Initial Default.
PAGE 603
Detailed Description To avoid shutdown, system performance has been degraded. Recommended Response Action Review system configuration, upgrade power supplies or reduce system power consumption. Category System Health SubCategory PWR = Power Usage Severity Severity 1 (Critical) Trap/EventID FALSE LCD Message System power exceeds threshold. Performance degraded. Check PSU configuration Initial Default.
PAGE 604
Category System Health SubCategory PWR = Power Usage Severity Severity 3 (Informational) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default. FALSE Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE PWR0102 Message The sleep button was pressed. Detailed Description None Recommended Response Action No response action is required.
PAGE 605
Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default. FALSE Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE PWR0104 Message The reset button was pressed. Detailed Description The system will reset. Recommended Response Action No response action is required.
PAGE 606
Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE PWR0106 Thearg1is latched. Message Arguments • arg1 = name Detailed Description None Recommended Response Action No response action is required. Category System Health SubCategory PWR = Power Usage Severity Severity 3 (Informational) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default.
PAGE 607
Initial Default. FALSE Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE PWR0108 Thearg1service was requested. Message Arguments • arg1 = name Detailed Description None Recommended Response Action No response action is required. Category System Health SubCategory PWR = Power Usage Severity Severity 3 (Informational) Trap/EventID FALSE LCD Message No LCD message display defined.
PAGE 608
LCD Message No LCD message display defined. Initial Default. FALSE Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE PWR2000 Message The system powered up. Detailed Description None Recommended Response Action No response action is required.
PAGE 609
Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE PWR2002 Message The system warm reset. Detailed Description None Recommended Response Action No response action is required. Category System Health SubCategory PWR = Power Usage Severity Severity 3 (Informational) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default.
PAGE 610
PWR2004 Message System booted automatically into diagnostics. Detailed Description None Recommended Response Action No response action is required. Category System Health SubCategory PWR = Power Usage Severity Severity 3 (Informational) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default.
PAGE 611
Detailed Description None Recommended Response Action No response action is required. Category System Health SubCategory PWR = Power Usage Severity Severity 3 (Informational) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default. FALSE Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE PWR2007 Message System restarted.
PAGE 612
Category System Health SubCategory PWR = Power Usage Severity Severity 3 (Informational) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default. FALSE Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE PWR2201 Message The system is sleeping with system hardware and processor context maintained.
PAGE 613
Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default. FALSE Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE PWR2203 Message The system is sleeping with system hardware and processor context lost. Detailed Description None Recommended Response Action No response action is required.
PAGE 614
Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE PWR2205 Message The system is in a soft-off state. Detailed Description None Recommended Response Action No response action is required. Category System Health SubCategory PWR = Power Usage Severity Severity 3 (Informational) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default.
PAGE 615
PWR2208 Message The system is in a sleep state. Detailed Description None Recommended Response Action No response action is required. Category System Health SubCategory PWR = Power Usage Severity Severity 3 (Informational) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default.
PAGE 616
Detailed Description None Recommended Response Action No response action is required. Category System Health SubCategory PWR = Power Usage Severity Severity 3 (Informational) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default. FALSE Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE PWR2211 Message The system is in legacy ON state.
PAGE 617
Category System Health SubCategory PWR = Power Usage Severity Severity 3 (Informational) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default. FALSE Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE PWR1009 Message System power capacity restored. Detailed Description None Recommended Response Action No response action is required.
PAGE 618
PAGE 619
30 RAC Event Messages RAC038 Message Unable to perform the operation due to an unknown error in iDRAC. Detailed Description The operation failed to run due to an unknown error in iDRAC. Recommended Response Action Retry the action. If this fails, reset iDRAC. Category Configuration SubCategory RAC = RAC Event Severity Severity 2 (Warning) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default.
PAGE 620
Initial Default. FALSE Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE RAC040 Missing parametersarg1. Message Arguments • arg1 = parameters Detailed Description One or more required parameters needed for the method invoked in the operation are missing. Recommended Response Action Verify that all required parameters are provided.
PAGE 621
Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE RAC042 Message Invalid number of input parameters. Detailed Description The number of input parameters provided is not valid to perform the operation. Recommended Response Action Verify that all required parameters are provided. Refer to the Lifecycle Controller-Remote Services documentation.
PAGE 622
RAC044 Message Unable to update some event filter settings. Detailed Description Some event filter settings were not updated due to problems encountered processing the input parameters. Recommended Response Action Verify the input parameters provided and retry the operation. Refer to the Lifecycle ControllerRemote Services documentation. Category Configuration SubCategory RAC = RAC Event Severity Severity 2 (Warning) Trap/EventID FALSE LCD Message No LCD message display defined.
PAGE 623
Detailed Description The event notficiation selected is not supported for the event filter specified. Recommended Response Action Refer to the iDRAC User Guide and Lifecycle Controller documentation and retry the operation with a valid event notification selection on the specified filter. Category Configuration SubCategory RAC = RAC Event Severity Severity 2 (Warning) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default.
PAGE 624
Category Configuration SubCategory RAC = RAC Event Severity Severity 3 (Informational) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default.
PAGE 625
31 RDU Event Messages RDU8500 CMCarg1: active Message Arguments • arg1 = slot number Detailed Description The CMC is identified in the message is active. Recommended Response Action No response action is required. Category Audit SubCategory RDU = Redundancy Severity Severity 3 (Informational) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default.
PAGE 626
Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default. LC Log Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE TRUE FALSE FALSE FALSE FALSE FALSE RDU8502 CMCarg1cannot go standby since the other CMC is not present or healthy. Message Arguments • arg1 = slot number Detailed Description For failover to occur, the standby CMC needs to be present, at the same version as the primary and healthy.
PAGE 627
Category Audit SubCategory RDU = Redundancy Severity Severity 3 (Informational) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default. LC Log Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE TRUE FALSE FALSE FALSE FALSE FALSE RDU8507 CMCarg1: disable failover Message Arguments • arg1 = slot number Detailed Description CMC failover is disabled.
PAGE 628
Recommended Response Action Check the status of the standby CMC and make sure the firmware version matches the primary CMC. Then reseat the CMC and retry the operation. If the issue persists, contact your service provider. Category Audit SubCategory RDU = Redundancy Severity Severity 3 (Informational) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default.
PAGE 629
Arguments • arg1 = slot number Detailed Description For failover to occur, the standby CMC needs to be present, at the same version as the primary and healthy. During failover, the active CMC resets and the standby CMC becomes active. This message is logged when the standby CMC is absent, unhealthy or at a different firmware version. Recommended Response Action Check the status of the standby CMC and make sure the firmware version matches the primary CMC. Then reseat the CMC and retry the operation.
PAGE 630
Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE TRUE FALSE FALSE FALSE FALSE FALSE RDU8512 CMCarg1: firmware versions are different [arg2arg3:arg4arg5] Message Arguments • • • • • arg1 = slot number arg2 = local fw version arg3 = factory revision arg4 = remote version arg5 = factory revision Detailed Description The firmware versions of the Active CMC and the Standby CMC are different.
PAGE 631
SubCategory RDU = Redundancy Severity Severity 3 (Informational) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default. LC Log Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE TRUE FALSE FALSE FALSE FALSE FALSE RDU8514 CMCarg1: cannot failover, firmware update is in progress.
PAGE 632
Category Audit SubCategory RDU = Redundancy Severity Severity 3 (Informational) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default. LC Log Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE TRUE FALSE FALSE FALSE FALSE FALSE RDU8516 CMCarg1: failover initiated by RACADM interface.
PAGE 633
Recommended Response Action No response action is required. Wait until the firmware update is complete and retry the operation. Category Audit SubCategory RDU = Redundancy Severity Severity 3 (Informational) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default.
PAGE 634
Detailed Description The communication between the primary and standby CMCs was lost. This may occur when the CMC identified in the message is restarting, or a firmware update operation is in progress. If the issue persists, a failover will occur. Recommended Response Action Wait for 10 minutes for: 1)Firmware update operations to complete and 2) The CMC to finish restarting. If the communication is not reestablished, remove and reinsert the CMC.
PAGE 635
Arguments • arg1 = slot number Detailed Description The active CMC has been removed from the chassis. If standby CMC is present, it will become active. Recommended Response Action Reinstall the CMC that was removed. Category Audit SubCategory RDU = Redundancy Severity Severity 3 (Informational) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default.
PAGE 636
RDU8523 CMCarg1: reset by peer CMC Message Arguments • arg1 = slot number Detailed Description The CMCidentified in the message was reset by other CMC. This occurs during failover and CMC firmware update to the standby CMC. Recommended Response Action No response action is required. Category Audit SubCategory RDU = Redundancy Severity Severity 3 (Informational) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default.
PAGE 637
Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE TRUE FALSE FALSE FALSE FALSE FALSE RDU0001 Message The fans are redundant. Detailed Description None Recommended Response Action No response action is required. Category System Health SubCategory RDU = Redundancy Severity Severity 3 (Informational) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default.
PAGE 638
RDU0003 Message Fan redundancy is degraded. Detailed Description One of more fans have failed or have been removed or a configuration change occurred which requires additional fans. Recommended Response Action Remove and re-install failed fans or install additional fans. Category System Health SubCategory RDU = Redundancy Severity Severity 2 (Warning) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default.
PAGE 639
Detailed Description One of more fans have failed or have been removed or a configuration change occurred which requires additional fans. Recommended Response Action Remove and re-install failed fans or install additional fans. Category System Health SubCategory RDU = Redundancy Severity Severity 1 (Critical) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default.
PAGE 640
Recommended Response Action Check the event log for power supply failures. Review system configuration and power consumption. Category System Health SubCategory RDU = Redundancy Severity Severity 1 (Critical) Trap/EventID 2473 LCD Message Lost PSU redundancy. Check PSU cables Initial Default.
PAGE 641
SubCategory RDU = Redundancy Severity Severity 3 (Informational) Trap/EventID 2475 LCD Message No LCD message display defined. Initial Default. LC Log Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset TRUE FALSE TRUE TRUE FALSE FALSE FALSE TRUE FALSE RDU0015 Message The power supplies are not redundant. Insufficient resources to maintain normal operations.
PAGE 642
Trap/EventID 2474 LCD Message No LCD message display defined. Initial Default. LC Log Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset TRUE FALSE TRUE TRUE FALSE FALSE FALSE FALSE TRUE RDU0030 Thearg1voltage is redundant.
PAGE 643
SubCategory RDU = Redundancy Severity Severity 2 (Warning) Trap/EventID 2474 LCD Message No LCD message display defined. Initial Default. LC Log Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset TRUE FALSE TRUE TRUE FALSE FALSE FALSE FALSE TRUE RDU0019 Message The storage voltage is not redundant.
PAGE 644
PAGE 645
32 RED Event Messages RED001 Message Job completed successfully. Detailed Description Job completed successfully. Recommended Response Action No response action is required. Category Updates SubCategory RED = FW Download Severity Severity 3 (Informational) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default.
PAGE 646
Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE TRUE TRUE FALSE FALSE FALSE TRUE FALSE RED006 Message Dell Update Package download failed. Detailed Description Dell Update Package download failed.
PAGE 647
RED008 Message Package extraction failed. Detailed Description Package extraction failed. Recommended Response Action Validate that the update package is not corrupt and is a valid Dell update package. Category Updates SubCategory RED = FW Download Severity Severity 2 (Warning) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default.
PAGE 648
PAGE 649
33 RFL Event Messages RFL2000 Internal Dual SD Modulearg1is present. Message Arguments • arg1 = name Detailed Description None Recommended Response Action No response action is required. Category System Health SubCategory RFL = IDSDM Media Severity Severity 3 (Informational) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default.
PAGE 650
Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default. FALSE Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE RFL2003 Internal Dual SD Modulearg1is online. Message Arguments • arg1 = name Detailed Description None Recommended Response Action No response action is required.
PAGE 651
Severity Severity 1 (Critical) Trap/EventID FALSE LCD Message Internal Dual SD Module failed. Check SD Card Initial Default. FALSE Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE RFL2005 Internal Dual SD Modulearg1is operating normally. Message Arguments • arg1 = name Detailed Description None Recommended Response Action No response action is required.
PAGE 652
SubCategory RFL = IDSDM Media Severity Severity 2 (Warning) Trap/EventID FALSE LCD Message Internal Dual SD Module is write protected. Check SD Card Initial Default. FALSE Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE RFL2007 Internal Dual SD Modulearg1is writable.
PAGE 653
Category System Health SubCategory RFL = IDSDM Media Severity Severity 3 (Informational) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default. FALSE Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE RFL2009 Internal Dual SD Modulearg1is enabled. Message Arguments • arg1 = name Detailed Description The Internal Dual SD Card redundancy feature was enabled.
PAGE 654
PAGE 655
34 RFLA Event Messages RFLA2001 Internal Dual SD Modulearg1is absent. Message Arguments • arg1 = name Detailed Description The SD card module is not detected or not installed. Recommended Response Action If unintended, reinstall the SD module. Category System Health SubCategory RFLA = IDSDM Absent Severity Severity 1 (Critical) Trap/EventID FALSE LCD Message Internal Dual SD Module is absent. Check SD card. Initial Default.
PAGE 656
PAGE 657
35 RFM Event Messages RFM1018 Message Removable Flash Media is absent. Detailed Description None Recommended Response Action No response action is required. Category System Health SubCategory RFM = FlexAddress SD Severity Severity 3 (Informational) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default.
PAGE 658
Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE RFM1020 Message Removable Flash Media is IPMI-function ready. Detailed Description None Recommended Response Action No response action is required. Category System Health SubCategory RFM = FlexAddress SD Severity Severity 3 (Informational) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default.
PAGE 659
RFM1022 Message Removable Flash Media is ready. Detailed Description None Recommended Response Action If unintended, reinstall the flash media. Category System Health SubCategory RFM = FlexAddress SD Severity Severity 3 (Informational) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default.
PAGE 660
Detailed Description At boot, the Card Identification (CID) signature of the card is different from the Non-volatile (NV) storage value or the card is the destination of a copy operation that is in-progress. Recommended Response Action If unintended, reinstall the flash media. Category System Health SubCategory RFM = FlexAddress SD Severity Severity 2 (Warning) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default.
PAGE 661
Category System Health SubCategory RFM = FlexAddress SD Severity Severity 1 (Critical) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default. FALSE Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE RFM1027 Message Removable Flash Media is operating normally. Detailed Description None Recommended Response Action No response action is required.
PAGE 662
Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default. FALSE Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE RFM1029 Message Removable Flash Media was deactivated. Detailed Description None Recommended Response Action No response action is required.
PAGE 663
Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE RFM1031 Message Removable Flash Media has finished booting. Detailed Description None Recommended Response Action No response action is required. Category System Health SubCategory RFM = FlexAddress SD Severity Severity 3 (Informational) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default.
PAGE 664
RFM1033 Message Removable Flash Media is writable. Detailed Description None Recommended Response Action No response action is required. Category System Health SubCategory RFM = FlexAddress SD Severity Severity 3 (Informational) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default.
PAGE 665
Detailed Description None Recommended Response Action No response action is required. Category System Health SubCategory RFM = FlexAddress SD Severity Severity 3 (Informational) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default.
PAGE 666
PAGE 667
36 RRDU Event Messages RRDU0001 Message Internal Dual SD Module is redundant. Detailed Description None Recommended Response Action No response action is required. Category System Health SubCategory RRDU = IDSDM Redundancy Severity Severity 3 (Informational) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default.
PAGE 668
Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE RRDU0003 Message Internal Dual SD Module redundancy is degraded. Detailed Description Either one of the SD card or both the SD cards are not functioning properly. Recommended Response Action Replace the failed SD card.
PAGE 669
RRDU0005 Message Internal Dual SD Module is not redundant. Insufficient resources to maintain normal operations. Detailed Description The current operating configuration cannot maintain redundancy.The unit may operate in a degraded state. Recommended Response Action Review product documentation and SD card configuration. Category System Health SubCategory RRDU = IDSDM Redundancy Severity Severity 1 (Critical) Trap/EventID FALSE LCD Message Internal Dual SD Module is not redundant.
PAGE 670
PAGE 671
37 SEC Event Messages SEC0001 Message The drive bay is open. Detailed Description The drive bay is open. A drive may be added or removed. System performance may be degraded. Recommended Response Action Close the drive bay. Check system logs. Category System Health SubCategory SEC = Security Event Severity Severity 1 (Critical) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default.
PAGE 672
Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE SEC0003 Message The processor area is open. Detailed Description The processor area is open. A drive may be added or removed. System performance may be degraded. Recommended Response Action Close the processor area. Check system logs.
PAGE 673
SEC0005 Message Unauthorized docking is detected. Detailed Description A removable component may have been tampered with, or installed incorrectly, or does not meet system requirements. Recommended Response Action Check removable hardware components for correct installation. Review installation documentation. Category System Health SubCategory SEC = Security Event Severity Severity 1 (Critical) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default.
PAGE 674
Detailed Description None Recommended Response Action No response action is required. Category System Health SubCategory SEC = Security Event Severity Severity 3 (Informational) Trap/EventID 2387 LCD Message No LCD message display defined. Initial Default. LC Log Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset TRUE FALSE TRUE TRUE FALSE FALSE FALSE FALSE TRUE SEC0017 Message The drive bay is closed.
PAGE 675
Category System Health SubCategory SEC = Security Event Severity Severity 3 (Informational) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default. FALSE Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE SEC0019 Message The processor area is closed. Detailed Description None Recommended Response Action No response action is required.
PAGE 676
Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default. FALSE Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE SEC0021 Message The docking is authorized. Detailed Description None Recommended Response Action No response action is required.
PAGE 677
Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE SEC0031 Message The chassis is open while the power is on. Detailed Description The chassis is open. System performance may be degraded, and security may be compromised. Recommended Response Action Close the chassis. Check system logs.
PAGE 678
SEC0033 Message The chassis is open while the power is off. Detailed Description The chassis is open while the power is off. System security may have been comprised. Recommended Response Action Close the chassis and verify hardware inventory. Check system logs. Category System Health SubCategory SEC = Security Event Severity Severity 1 (Critical) Trap/EventID 2385 LCD Message Intrusion detected. Check chassis cover Initial Default.
PAGE 679
Detailed Description The chassis is open. System performance may be degraded, and security may be compromised. Recommended Response Action Close the chassis. Check system logs. Category System Health SubCategory SEC = Security Event Severity Severity 1 (Critical) Trap/EventID 2385 LCD Message Intrusion detected. Check chassis cover Initial Default.
PAGE 680
Category System Health SubCategory SEC = Security Event Severity Severity 1 (Critical) Trap/EventID FALSE LCD Message BIOS detected an error configuring TXT. Check system configuration. Initial Default. FALSE Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE SEC0042 Message Processor detected an error while performing an Intel Trusted Execution Technology (TXT) operation.
PAGE 681
Severity Severity 1 (Critical) Trap/EventID FALSE LCD Message BIOS detected a TXT error during POST. Check system configuration. Initial Default. FALSE Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE SEC0044 Message SINIT Authenticated Code Module detected an Intel Trusted Execution Technology (TXT) error at boot. Detailed Description TXT initialization failure.
PAGE 682
LCD Message No LCD message display defined. Initial Default. FALSE Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE SEC0601 Message A secure mode violation was corrected. Detailed Description None Recommended Response Action No response action is required.
PAGE 683
Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE SEC0603 Message User password violation was corrected. Detailed Description None Recommended Response Action No response action is required. Category System Health SubCategory SEC = Security Event Severity Severity 3 (Informational) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default.
PAGE 684
SEC0605 Message A setup password violation was corrected. Detailed Description None Recommended Response Action No response action is required. Category System Health SubCategory SEC = Security Event Severity Severity 3 (Informational) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default.
PAGE 685
Detailed Description None Recommended Response Action No response action is required. Category System Health SubCategory SEC = Security Event Severity Severity 3 (Informational) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default. FALSE Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE SEC0608 Message A password violation detected.
PAGE 686
Category System Health SubCategory SEC = Security Event Severity Severity 3 (Informational) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default. FALSE Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE SEC0610 Message An Out-of-band password violation detected. Detailed Description This may apply to a remote access attempt.
PAGE 687
Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default. FALSE Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE SEC0045 Message Intel Trusted Execution Technology (TXT) is operating correctly. Detailed Description None Recommended Response Action No response action is required.
PAGE 688
PAGE 689
38 SEL Event Messages SEL0002 Message Logging is disabled. Detailed Description This message appears when event logging of a specific type is disabled by the user. (IPMI sensor type code 10h - offset 01h) Recommended Response Action If unintended, re-enable logging. Category System Health SubCategory SEL = Sys Event Log Severity Severity 1 (Critical) Trap/EventID 2377 LCD Message No LCD message display defined. Initial Default.
PAGE 690
Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset TRUE FALSE TRUE TRUE FALSE FALSE FALSE FALSE TRUE SEL0004 Message Log cleared. Detailed Description None Recommended Response Action No response action is required. Category System Health SubCategory SEL = Sys Event Log Severity Severity 3 (Informational) Trap/EventID 2379 LCD Message No LCD message display defined. Initial Default.
PAGE 691
SEL0007 Message All event logging is enabled. Detailed Description None Recommended Response Action No response action is required. Category System Health SubCategory SEL = Sys Event Log Severity Severity 3 (Informational) Trap/EventID 2379 LCD Message No LCD message display defined. Initial Default.
PAGE 692
SEL0010 Message System event log (SEL) is almost full. Detailed Description When the event log is full, additional events are not written to the log or older events will be overwritten and lost. (IPMI sensor type code 10h - offset 05h) Recommended Response Action Backup and clear log at the next maintained time. Category System Health SubCategory SEL = Sys Event Log Severity Severity 2 (Warning) Trap/EventID 2378 LCD Message No LCD message display defined. Initial Default.
PAGE 693
Detailed Description None Recommended Response Action No response action is required. Category System Health SubCategory SEL = Sys Event Log Severity Severity 3 (Informational) Trap/EventID 2379 LCD Message No LCD message display defined. Initial Default. LC Log Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset TRUE FALSE TRUE TRUE FALSE FALSE FALSE FALSE TRUE SEL1200 Message The system was reconfigured.
PAGE 694
Category System Health SubCategory SEL = Sys Event Log Severity Severity 3 (Informational) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default. FALSE Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE SEL1204 Message An unknown system hardware failure detected. Detailed Description The operating system or BIOS detected an unknown event.
PAGE 695
Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default. FALSE Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE SEL1206 Message An entry was added to auxiliary log. Detailed Description None Recommended Response Action No response action is required.
PAGE 696
Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE SEL1208 Message A platform event filter action was executed. Detailed Description None Recommended Response Action No response action is required. Category System Health SubCategory SEL = Sys Event Log Severity Severity 3 (Informational) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default.
PAGE 697
SEL1210 Message The time-stamp clock is synchronized. Detailed Description None Recommended Response Action No response action is required. Category System Health SubCategory SEL = Sys Event Log Severity Severity 3 (Informational) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default.
PAGE 698
Detailed Description System setup displays the system boot order. The local video screen may also show additional information. (IPMI sensor type code 1eh - offset 00h) Recommended Response Action Check system boot settings. Check mass storage controller configuration settings is applicable. Category System Health SubCategory SEL = Sys Event Log Severity Severity 1 (Critical) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default.
PAGE 699
Category System Health SubCategory SEL = Sys Event Log Severity Severity 1 (Critical) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default. FALSE Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE SEL1303 Message Bootable diskette detected. Detailed Description None Recommended Response Action No response action is required.
PAGE 700
Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default. FALSE Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE SEL1305 Message The PXE server found. Detailed Description None Recommended Response Action No response action is required.
PAGE 701
Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE SEL1307 Message Boot sector found. Detailed Description None Recommended Response Action No response action is required. Category System Health SubCategory SEL = Sys Event Log Severity Severity 3 (Informational) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default.
PAGE 702
SEL1309 Message User selected a boot source. Detailed Description None Recommended Response Action No response action is required. Category System Health SubCategory SEL = Sys Event Log Severity Severity 3 (Informational) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default.
PAGE 703
Detailed Description None Recommended Response Action No response action is required. Category System Health SubCategory SEL = Sys Event Log Severity Severity 3 (Informational) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default. FALSE Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE SEL1404 Message A platform event trap (PET) was generated.
PAGE 704
Category System Health SubCategory SEL = Sys Event Log Severity Severity 3 (Informational) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default. FALSE Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE SEL9900 Message An unsupported event occurred. Detailed Description The current software version cannot decode this event.
PAGE 705
Category System Health SubCategory SEL = Sys Event Log Severity Severity 2 (Warning) Trap/EventID 2378 LCD Message No LCD message display defined. Initial Default. LC Log Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset TRUE FALSE TRUE TRUE FALSE FALSE FALSE FALSE TRUE SEL1507 Communications restored with Chassis Group Memberarg1.
PAGE 706
Recommended Response Action 1)Check that the Name or IP address, User Name, and Password of the member are correct. 2)Check that the member is not a leader or member of another group. 3)Check that the member can be reached by the leader. Category System Health SubCategory SEL = Sys Event Log Severity Severity 2 (Warning) Trap/EventID 2378 LCD Message No LCD message display defined. Initial Default.
PAGE 707
Detailed Description Group master CMC could not log into the group member CMC. Recommended Response Action Check login credentials of CMC Category System Health SubCategory SEL = Sys Event Log Severity Severity 2 (Warning) Trap/EventID 2378 LCD Message No LCD message display defined. Initial Default.
PAGE 708
Detailed Description None Recommended Response Action No response action is required. Category System Health SubCategory SEL = Sys Event Log Severity Severity 3 (Informational) Trap/EventID 2379 LCD Message No LCD message display defined. Initial Default. LC Log Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset TRUE FALSE TRUE TRUE FALSE FALSE FALSE TRUE FALSE SEL1501 Message Chassis management controller (CMC) redundancy is lost.
PAGE 709
Recommended Response Action Chassis management controller (CMC) redundancy is degraded. Category System Health SubCategory SEL = Sys Event Log Severity Severity 2 (Warning) Trap/EventID 2378 LCD Message No LCD message display defined. Initial Default. LC Log Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset TRUE FALSE TRUE TRUE FALSE FALSE FALSE FALSE TRUE SEL1503 Message The chassis management controller (CMC) is not redundant.
PAGE 710
SubCategory SEL = Sys Event Log Severity Severity 1 (Critical) Trap/EventID 2377 LCD Message No LCD message display defined. Initial Default. LC Log Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset TRUE FALSE TRUE TRUE FALSE FALSE FALSE TRUE FALSE SEL9901 Message OEM software event. Detailed Description The current software version cannot decode this event.
PAGE 711
Severity Severity 3 (Informational) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default.
PAGE 712
PAGE 713
39 STOR Event Messages STOR1 A devicearg1is in an unknown state. Message Arguments • arg1 = device name Detailed Description The controller cannot communicate with a device. The state of the device cannot be determined. There may be a bad or loose cable, or a missing device, or a problem with the driver or firmware. Recommended Response Action See the storage hardware documentation for information on checking the cables. Check for problems with any enclosures attached to the system.
PAGE 714
Severity Severity 3 (Informational) Trap/EventID 4179 LCD Message No LCD message display defined. Initial Default. SNMP Alert;#LCD;#Remote System Log Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset TRUE FALSE TRUE TRUE TRUE FALSE FALSE TRUE FALSE STOR3 CEM Storage Management has lost communication with thearg1. Message Arguments • arg1 = Controller Name Detailed Description Storage Management has lost communication with a controller.
PAGE 715
Severity Severity 1 (Critical) Trap/EventID 4177 LCD Message No LCD message display defined. Initial Default. SNMP Alert;#LCD;#Remote System Log Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset TRUE FALSE TRUE TRUE TRUE FALSE FALSE TRUE FALSE STOR5 Redundancy lost.arg1 Message Arguments • arg1 = VD/Enclosure Name Detailed Description A virtual disk or enclosure has lost data redundancy.
PAGE 716
Detailed Description A comparison of storage inventory collected before and after the host re-boot/re-set. reports differences. There could have been some storage components added or removed when the host was powered down. Recommended Response Action No response action is required. Category Storage SubCategory STOR = Storage Severity Severity 3 (Informational) Trap/EventID 4179 LCD Message No LCD message display defined. Initial Default.
PAGE 717
Detailed Description High Availability RAID is not supported by this firmware release. This event may occur during the upgrade process. Recommended Response Action Remove one RAID controller. Category Storage SubCategory STOR = Storage Severity Severity 2 (Warning) Trap/EventID 4178 LCD Message No LCD message display defined. Initial Default.
PAGE 718
Recommended Response Action Update the Chassis Infrastructure firmware. Category Storage SubCategory STOR = Storage Severity Severity 1 (Critical) Trap/EventID 4177 LCD Message No LCD message display defined. Initial Default. LCD;#Remote System Log Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset TRUE FALSE TRUE TRUE TRUE FALSE FALSE TRUE FALSE STOR11 Message The currently detected hardware configuration is High Availability Ready.
PAGE 719
Category Configuration SubCategory STOR = Storage Severity Severity 2 (Warning) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default.
PAGE 720
Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default. FALSE Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE STOR007 Message Resource Allocation Failure. Detailed Description Command failed due to lack of memory or file space. Recommended Response Action Reset iDRAC and run the command.
PAGE 721
Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE STOR010 Message RAID level not supported on controller Detailed Description RAID level provided not valid for this controller Recommended Response Action Provide a valid RAID level Category Configuration SubCategory STOR = Storage Severity Severity 2 (Warning) Trap/EventID FALSE LCD Message No LCD message display defined.
PAGE 722
STOR012 Message Provided Physical disk not valid for this operation Detailed Description One or more of provided physical disks cannot be used. Recommended Response Action Check the RAID profile for correct status and use of provided physical disk(s) Category Configuration SubCategory STOR = Storage Severity Severity 2 (Warning) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default.
PAGE 723
Detailed Description Hit maximum limit for virtual disks on the controller Recommended Response Action A new virtual disk cannot be created until one is deleted. Category Configuration SubCategory STOR = Storage Severity Severity 2 (Warning) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default.
PAGE 724
Category Configuration SubCategory STOR = Storage Severity Severity 2 (Warning) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default. FALSE Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE STOR018 Message No foreign drives detected Detailed Description This operation did not detect any foreign drives.
PAGE 725
Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default. FALSE Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE STOR020 Message Controller Key is already present Detailed Description Controller key cannot be set because the key is already present. Recommended Response Action Controller already has a key. Key must be deleted to key the controller again.
PAGE 726
Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE STOR022 Message Controller is not security capable Detailed Description Controller does not have the capability to secure virtual disks Recommended Response Action Controller does not have security capability.
PAGE 727
STOR024 Message Configuration already committed, cannot commit until previous commit succeeds or is cancelled Detailed Description Configuration changes are already scheduled Recommended Response Action Configuration is already scheduled. No need to schedule again. Category Configuration SubCategory STOR = Storage Severity Severity 3 (Informational) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default.
PAGE 728
STOR026 Message Configuration Job not Created, there are no pending Configuration changes Detailed Description There are no pending configuration changes for this device, the job cant be created. Recommended Response Action There were no pending configuration changes found; the configuration job cannot be created when there are pending configuration changes.
PAGE 729
Detailed Description Could not find the provided virtual disk Recommended Response Action Provide a valid virtual disk FQDD. Category Configuration SubCategory STOR = Storage Severity Severity 2 (Warning) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default.
PAGE 730
Category Configuration SubCategory STOR = Storage Severity Severity 2 (Warning) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default. FALSE Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE STOR031 Message Lifecycle Controller is not enabled. Detailed Description For 11G systems: System Services must be enabled to perform the requested operation.
PAGE 731
Recommended Response Action Wait for current Lifecycle Controller operation to complete. Verify that the system is 1) Not currently in Lifecycle Controller Unified Server Configurator 2) Not waiting for user intervention at F1/F2 POST error 3) Not in any of the device or controller Option ROMs and retry the operation. Category Configuration SubCategory STOR = Storage Severity Severity 2 (Warning) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default.
PAGE 732
Category Configuration SubCategory STOR = Storage Severity Severity 2 (Warning) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default.
PAGE 733
Recommended Response Action Provide a valid parameter value for specifed parameter Category Configuration SubCategory STOR = Storage Severity Severity 2 (Warning) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default.
PAGE 734
Recommended Response Action Provide valid attribute Category Configuration SubCategory STOR = Storage Severity Severity 2 (Warning) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default.
PAGE 735
Detailed Description The attribute value is not supported in the current configuration Recommended Response Action Provide a settable value for the specifed attribute by refering the possible values for that attribute Category Configuration SubCategory STOR = Storage Severity Severity 2 (Warning) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default.
PAGE 736
Category Configuration SubCategory STOR = Storage Severity Severity 2 (Warning) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default.
PAGE 737
Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default. FALSE Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE STOR047 AttributeValue cannot be changed for ReadOnly Attribute Namearg1 Message Arguments • arg1 = attribute Detailed Description AttributeValue cannot be changed for ReadOnly Attribute Name Recommended Response Action Cannot change this attribute.
PAGE 738
LCD Message No LCD message display defined. Initial Default. FALSE Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE STOR049 Message Controller is in Local Key Management mode Detailed Description Controller is in Local Key Management mode Recommended Response Action No response action is required.
PAGE 739
Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE STOR051 Message StartingLBA and Size combination goes beyond Physical Disk size Detailed Description The starting LBA and size parameters are incorrect Recommended Response Action Refer to the users guide to provide the correct StartingLBA and Size combination Category Configuration SubCategory STOR = Storage Severity Severity 2 (Warning)
PAGE 740
STOR053 Message Controller key not present, controller needs key from Dell Key Management Server Detailed Description System could not obtain key from the Dell Key Management Server Recommended Response Action Refer to the DKM documentation for setting the Key management server. Category Configuration SubCategory STOR = Storage Severity Severity 2 (Warning) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default.
PAGE 741
Detailed Description The BIOS is not Dell Key Management capable Recommended Response Action Informational Message. Refer to the controller users guide for more info. Category Configuration SubCategory STOR = Storage Severity Severity 3 (Informational) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default.
PAGE 742
Recommended Response Action Enable CSIOR and then run CSIOR. Invoke the GetRSStatus wsman method(Refer LCManagement profile document for more details on this method). This method returns Status and wait for Status to become "Ready" Category Configuration SubCategory STOR = Storage Severity Severity 3 (Informational) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default.
PAGE 743
SubCategory STOR = Storage Severity Severity 2 (Warning) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default. FALSE Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE STOR060 Message Configuration not supported on RAID controller. Detailed Description The operation is not supported on the target device.
PAGE 744
Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default. None Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE STOR063 Message Cannot assign the Virtual Disk to multiple Virtual Adapters in single assignment mode.
PAGE 745
Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE 745
PAGE 746
PAGE 747
40 SUP Event Messages SUP001 Message Insufficient parameters provided. Detailed Description Insufficient Parameters provided for the WSMAN command. Recommended Response Action Make sure the parameters are correct and in the right number and format and retry the action. Category Updates SubCategory SUP = FW Update Job Severity Severity 2 (Warning) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default.
PAGE 748
Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE SUP005 Message Invalid reboot value. Detailed Description Reboot value specified is not supported. Recommended Response Action Verify the reboot value and retry the action.
PAGE 749
SUP015 Message Input parameters values should not be NULL. Detailed Description One of the parameters specified received a NULL value that prevented the action from completing. Recommended Response Action Correct the parameter value and retry the command. Category Updates SubCategory SUP = FW Update Job Severity Severity 2 (Warning) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default.
PAGE 750
Detailed Description The specified start time is invalid. Recommended Response Action Start Time should be in the form YYYYMMDDHHMMSS. Or it should be TIME_NOW to specify an immediate update or reboot. Verify the specified start time and retry the action. Category Updates SubCategory SUP = FW Update Job Severity Severity 2 (Warning) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default.
PAGE 751
Category Updates SubCategory SUP = FW Update Job Severity Severity 3 (Informational) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default. FALSE Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE SUP022 Message Job store has reached the maximum storage limit. Detailed Description JobStore file has exceeded the size limit.
PAGE 752
Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default.
PAGE 753
41 SWC Event Messages SWC8533 Message Unable to complete delete all keys operation for service accounts for all slots due to problem saving key file. Detailed Description The delete all keys for service accounts for all slots operation did not complete successfully due to problems encounterered while saving the key file. Recommended Response Action Retry the operation. If the issue persists, contact your service provider.
PAGE 754
Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE TRUE FALSE FALSE FALSE FALSE FALSE SWC8535 Unable to add key for slotarg1of service account, due to problem saving key file. Message Arguments • arg1 = slot number Detailed Description Public Key (PK) SSH Authentication key file upload did not complete successfully because Chassis Management Controller is unable to access the configuration database.
PAGE 755
Initial Default. LC Log Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE TRUE FALSE FALSE FALSE FALSE FALSE SWC8537 Unable to add key for slotarg1of service account, due to the key being too long. Message Arguments • arg1 = slot number Detailed Description The add key operation did not complete successfully for the slot identified in the message due to the key being too long. Recommended Response Action Retry the operation.
PAGE 756
LCD Message No LCD message display defined. Initial Default. LC Log Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE TRUE FALSE FALSE FALSE FALSE FALSE SWC8539 The key delete operation successfully completed for slotarg1of service account.
PAGE 757
Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default. LC Log Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE TRUE FALSE FALSE FALSE FALSE FALSE SWC8500 Unable to generate Profile with [arg1] settings. Message Arguments • arg1 = number of entries Detailed Description Unable to communicate with iDRAC. Recommended Response Action Check if iDRAC is ready and system is running properly.
PAGE 758
SubCategory SWC = Software Config Severity Severity 1 (Critical) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default. LC Log Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE TRUE FALSE FALSE FALSE FALSE FALSE SWC8502 A Profile was generated with [arg1] settings.
PAGE 759
Recommended Response Action No response action is required. Category Audit SubCategory SWC = Software Config Severity Severity 3 (Informational) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default. LC Log Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE TRUE FALSE FALSE FALSE FALSE FALSE SWC8504 arg1Profile renamed toarg2and description edited.
PAGE 760
Detailed Description The description for the Profile identified in the message was edited. Recommended Response Action No response action is required. Category Audit SubCategory SWC = Software Config Severity Severity 3 (Informational) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default.
PAGE 761
Detailed Description A new Profile identified in the message has been created. Recommended Response Action No response action is required. Category Audit SubCategory SWC = Software Config Severity Severity 3 (Informational) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default.
PAGE 762
Arguments • • arg1 = profile name arg2 = slot number Detailed Description Unable to communicated with iDRAC. Recommended Response Action Check if iDRAC is ready and system is running properly. Utilize the RACADM command by running "racadm getversion" to list all the servers and make sure the iDRAC version is displayed. If the iDRAC is listed as Not Ready then wait until it becomes ready. A Virtual Reseat may be required.
PAGE 763
Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE TRUE FALSE FALSE FALSE FALSE FALSE SWC8511 Userarg1was successfully addedl. Message Arguments • arg1 = user name Detailed Description The user name identified in the message was added successfully. Recommended Response Action No response action is required.
PAGE 764
LCD Message No LCD message display defined. Initial Default. LC Log Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE TRUE FALSE FALSE FALSE FALSE FALSE SWC8513 Successfully deleted Userarg1. Message Arguments • arg1 = user name Detailed Description The user name identified in the message was successfully deleted. Recommended Response Action No response action is required.
PAGE 765
Severity Severity 2 (Warning) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default. LC Log Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE TRUE FALSE FALSE FALSE FALSE FALSE SWC8515 Successfully modified privileges of Userarg1. Message Arguments • arg1 = user name Detailed Description Successfully modified privileges of User identified in the message.
PAGE 766
Category Audit SubCategory SWC = Software Config Severity Severity 2 (Warning) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default. LC Log Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE TRUE FALSE FALSE FALSE FALSE FALSE SWC8517 Successfully modified password of Userarg1.
PAGE 767
Detailed Description Unable to modify the password of the User identified in the message. Recommended Response Action Make sure: 1) The login credentials for the operation have user config administration privilege, 2) The user name and password given are valid. If the issue persists, restart the CMC and retry the operation. Category Audit SubCategory SWC = Software Config Severity Severity 2 (Warning) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default.
PAGE 768
Arguments • • • • arg1 = original user name arg2 = new_user name arg3 = error code arg4 = error message Detailed Description Unable to modify the user name specified in the message. Recommended Response Action Make sure: 1) The login credentials for the operation have user config administration privilege, 2) The user name given is valid. If the issue persists, restart the CMC and retry the operation.
PAGE 769
Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE TRUE FALSE FALSE FALSE FALSE FALSE SWC8522 Chassis Group Leader update of memberarg1configuration successful. Message Arguments • arg1 = member id Detailed Description Successfully completed a configuration sync with the member identified in the message. Recommended Response Action No response action required.
PAGE 770
Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default. LC Log Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE TRUE FALSE FALSE FALSE FALSE FALSE SWC8524 Unable to addarg1to Chassis Group because a member already exists with the same addressing information.
PAGE 771
SubCategory SWC = Software Config Severity Severity 3 (Informational) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default.
PAGE 772
Recommended Response Action Make sure the user name is valid. If communication with iDRAC is not successful, reset the iDRAC. Retry the operation after a few minutes. Category Audit SubCategory SWC = Software Config Severity Severity 3 (Informational) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default.
PAGE 773
Recommended Response Action If communications with the iDRAC is not functioning, reset the iDRAC and retry the operation after a few minutes. Run the RACADM command "racadm ping server- " to check the communications. If the communications are not functional, restart the iDRAC by performing a Virtual Reseat of the server using the RACADM command "racadm racreset -m server-".
PAGE 774
Detailed Description The Chassis Management Controller is unable to set the administrator role for the iDRAC root user. This can happen if the communction to the iDRAC from CMC is non-functional or iDRAC is rebooting. Recommended Response Action If communications with the iDRAC is not functioning, reset the iDRAC and retry the operation after a few minutes. Run the RACADM command "racadm ping server- " to check the communications.
PAGE 775
SWC8600 Selected profile was not applied toarg1 Message Arguments • arg1 = server list Detailed Description The profile version must be compatible with the server generation and LC version. Recommended Response Action When attempting application, ensure that profile versions are compatible with target servers. Category Audit SubCategory SWC = Software Config Severity Severity 2 (Warning) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default.
PAGE 776
Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE SWC8602 Quick Deploy Profile for serverarg1failed: unable to get mutex. Message Arguments • arg1 = server number Detailed Description The system is busy with other operations. Please wait and retry the operation.
PAGE 777
Initial Default. None Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE SWC8604 Quick Deploy Profile: Serverarg1cannot accept profile. Message Arguments • arg1 = server number Detailed Description The target server does not support server cloning.
PAGE 778
LCD Message No LCD message display defined. Initial Default. None Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE SWC8606 Message Quick Deploy Profile: Timeout exceeded while waiting for remote services ready on Serverarg1. Arguments • arg1 = server number Detailed Description The target server never reported that remote services were ready.
PAGE 779
Severity Severity 3 (Informational) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default. None Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE SWC8608 Request [arg1] for Server in Slotarg2failed.
PAGE 780
Detailed Description The server Lifcycle Controller responded with a failure for a WSMAN request. Recommended Response Action Verify correct operation of Lifecycle Controller on target server Category Audit SubCategory SWC = Software Config Severity Severity 2 (Warning) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default.
PAGE 781
SWC8611 Profile "arg1" and Server (Service Tag:arg2in Slotarg3are not compatible. Message Arguments • • • arg1 = profile_name arg2 = service tag arg3 = server_number Detailed Description The selected profile version and the target server are not compatible. The CMC cannot perform the cloning operation.
PAGE 782
Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE SWC8613 Failed to Fully Extractarg1Boot List Settings from Stored Profile Message Arguments • arg1 = boot_list_name Detailed Description The selected profile is corrupt. Recreate a new profile with the desired properties, or use a different profile.
PAGE 783
Initial Default. None Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE SWC4004 A firmware or software incompatibility detected between iDRAC in slotarg1and CMC. Message Arguments • arg1 = number Detailed Description FlexAddress is not implemented in one of the versions of firmware. Please update the firmware. Recommended Response Action Check firmware versions of iDRAC and CMC.
PAGE 784
LCD Message No LCD message display defined. Initial Default. LC Log Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset TRUE FALSE TRUE TRUE FALSE FALSE FALSE TRUE FALSE SWC4006 A firmware or software incompatibility detected between system BIOS in slotarg1and CMC. Message Arguments • arg1 = number Detailed Description FlexAddress is not implemented in one of the versions of firmware. Please update the firmware.
PAGE 785
Severity Severity 3 (Informational) Trap/EventID 2339 LCD Message No LCD message display defined. Initial Default. LC Log Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset TRUE FALSE TRUE TRUE FALSE FALSE FALSE TRUE FALSE SWC4008 Message A firmware or software incompatibility detected between CMC 1 and CMC 2. Detailed Description FlexAddress is not implemented in one of the versions of firmware. Please update the firmware.
PAGE 786
Initial Default. LC Log Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset TRUE FALSE TRUE TRUE FALSE FALSE FALSE FALSE TRUE SWC5000 arg1upgrade was successful. Message Arguments • arg1 = name Detailed Description None Recommended Response Action No response action is required. Category System Health SubCategory SWC = Software Config Severity Severity 3 (Informational) Trap/EventID FALSE LCD Message No LCD message display defined.
PAGE 787
LCD Message No LCD message display defined. Initial Default. FALSE Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE SWC5002 arg1upgrade was successful but encountered minor errors. Message Arguments • arg1 = name Detailed Description None Recommended Response Action Check system logs for minor errors.
PAGE 788
PAGE 789
42 SWU Event Messages SWU8500 The schedule toarg1Lifecycle Controller on serverarg2was not successful. Message Arguments • • arg1 = update/reinstall/rollback arg2 = slot number Detailed Description This message is displayed when: 1. A reboot job is unable to provide a valid reboot ID. 2. The WSMAN command to set up a job queue on Lifecycle Controller was not successful. Recommended Response Action Retry the operation. If the error persists, contact your service provider.
PAGE 790
Severity Severity 2 (Warning) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default. LC Log Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE TRUE FALSE FALSE FALSE FALSE FALSE SWU8502 A request was submitted to schedule thearg1operation of Lifecycle Controller on serverarg2.
PAGE 791
Category Updates SubCategory SWU = Software Change Severity Severity 3 (Informational) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default. LC Log Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE TRUE FALSE FALSE FALSE FALSE FALSE SWU8504 Successfully scheduled the Lifecycle Controllerarg1operation on the serverarg2.
PAGE 792
Recommended Response Action No response action required. Category Updates SubCategory SWU = Software Change Severity Severity 3 (Informational) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default. LC Log Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE TRUE FALSE FALSE FALSE FALSE FALSE SWU8506 Completed the Firmware update operation for CMCarg1.
PAGE 793
Detailed Description The firmware update operation of IOM infrastructure is successful. Recommended Response Action No response action is required. Category Updates SubCategory SWU = Software Change Severity Severity 3 (Informational) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default.
PAGE 794
Arguments • arg1 = error no Detailed Description The IOM firmware update operation was not successful. Unable to initiate the Update process. Recommended Response Action Retry the operation. Category Updates SubCategory SWU = Software Change Severity Severity 2 (Warning) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default.
PAGE 795
SWU8517 Unable to update the iDRAC firmware on the server in slotarg1. The Image file is not accessible. ErrorCode=0xarg2. Message Arguments • • arg1 = slot number arg2 = error no Detailed Description Unable to update the iDRAC firmware. The firmware Image file is not accessible. Recommended Response Action Make sure the iDRAC firmware Image file is available in the given path and retry the operation.
PAGE 796
Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE TRUE FALSE FALSE FALSE FALSE FALSE SWU8519 The firmware update operation of the iDRAC on the server in slotarg1is stopped. The Image file is corrupted. Message Arguments • arg1 = slot number Detailed Description The iDRAC firmware update operation was stopped, because the Image file is corrupted.
PAGE 797
Initial Default. LC Log Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE TRUE FALSE FALSE FALSE FALSE FALSE SWU8521 The firmware update operation of the iDRAC on the server in slotarg1was stopped. The selected Image file is not compatible with the server hardware. Message Arguments • arg1 = slot number Detailed Description The firmware update operation of iDRAC identified in the message was stopped.
PAGE 798
Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default. LC Log Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE TRUE FALSE FALSE FALSE FALSE FALSE SWU8523 The firmware update operation of the iDRAC on the server in slotarg1is successfully completed. Message Arguments • arg1 = slot number Detailed Description The firmware update operation of the iDRAC identified in the mesaage is successful.
PAGE 799
SubCategory SWU = Software Change Severity Severity 2 (Warning) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default. LC Log Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE TRUE FALSE FALSE FALSE FALSE FALSE SWU8525 Unable to update the iDRAC firmware on the server in slotarg1. The firmware update timeout limit is exceeded.
PAGE 800
Recommended Response Action No response action is required. Category Updates SubCategory SWU = Software Change Severity Severity 3 (Informational) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default. LC Log Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE TRUE FALSE FALSE FALSE FALSE FALSE SWU8527 Message Successfully completed the iKVM firmware update.
PAGE 801
SubCategory SWU = Software Change Severity Severity 2 (Warning) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default. LC Log Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE TRUE FALSE FALSE FALSE FALSE FALSE SWU8529 Message Unable to update the iKVM firmware, because the Image file was not transferred to the iKVM target.
PAGE 802
Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default. LC Log Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE TRUE FALSE FALSE FALSE FALSE FALSE SWU8531 Message Unable to update the iKVM firmware. The firmware update timeout limit is exceeded.
PAGE 803
Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default. LC Log Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE TRUE FALSE FALSE FALSE FALSE FALSE SWU8533 Unable to update the LKVM firmware, because the target is not ready. ErrorCode=0xarg1. Message Arguments • arg1 = error no Detailed Description The LKVM firmware update operation is not successful, because the target is not ready.
PAGE 804
LCD Message No LCD message display defined. Initial Default. LC Log Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE TRUE FALSE FALSE FALSE FALSE FALSE SWU8535 Message Unable to update the LKVM firmware, because the Image file transfer is not successful. ErrorCode=0xarg1.
PAGE 805
Severity Severity 2 (Warning) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default. LC Log Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE TRUE FALSE FALSE FALSE FALSE FALSE SWU8537 Message Unable to update the LKVM firmware, because the IP address provided is invalid. ErrorCode=0xarg1.
PAGE 806
Category Updates SubCategory SWU = Software Change Severity Severity 2 (Warning) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default. LC Log Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE TRUE FALSE FALSE FALSE FALSE FALSE SWU8540 Message Unable to update the PSU firmware, because the transfer of Image file is not successful. ErrorCode=0xarg1.
PAGE 807
Detailed Description The PSU firmware update operation was not successful, because the firmware Image file could not be transferred. Recommended Response Action Make sure that the PSU firmware image file is available at the location specified in the operation, and then retry the operation. Category Updates SubCategory SWU = Software Change Severity Severity 2 (Warning) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default.
PAGE 808
Recommended Response Action Make sure that the CMC firmware image file is available at the location specified in the oepration, and then retry the operation. Category Updates SubCategory SWU = Software Change Severity Severity 2 (Warning) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default.
PAGE 809
SubCategory SWU = Software Change Severity Severity 2 (Warning) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default. LC Log Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE TRUE FALSE FALSE FALSE FALSE FALSE SWU8546 Message Unable to update the Standby CMC firmware. Detailed Description The firmware update operation of the Standby CMC was not successful.
PAGE 810
LCD Message No LCD message display defined. Initial Default. LC Log Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE TRUE FALSE FALSE FALSE FALSE FALSE SWU8548 Message Unable to update the Standby CMC firmware. The Image was not accessible. Detailed Description The firmware update operation of Standby CMC was not successful. The firmware image could not be accessed.
PAGE 811
Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE TRUE FALSE FALSE FALSE FALSE FALSE SWU8550 Message Unable to update the firmware of Standby CMC and Active CMC. Detailed Description The firmware update process of Active CMC and Standby CMC was not successful. Recommended Response Action Reacquire the Image file from the source location, and then retry the operation.
PAGE 812
SWU8552 Message Unable to update the firmware of Active CMC. Detailed Description The firmware update process of Active CMC was not successful. Recommended Response Action Reacquire the Image file from the source location, and then retry the operation. Category Updates SubCategory SWU = Software Change Severity Severity 2 (Warning) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default.
PAGE 813
Detailed Description Local CMC firmware update process is initiated. Recommended Response Action No response action is required. Category Updates SubCategory SWU = Software Change Severity Severity 3 (Informational) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default.
PAGE 814
Detailed Description A chassis-wide switch configuration image is applied to the first node of a multi-node sled upon insertion or chassis initialization and has failed. Recommended Response Action Make sure the sled has an updated iDRAC firmware. Category Audit SubCategory SWU = Software Change Severity Severity 2 (Warning) Trap/EventID 8362 LCD Message No LCD message display defined. Initial Default.
PAGE 815
43 SYS Event Messages SYS001 Message The operation was successful. Detailed Description The operation requested successfully completed. Recommended Response Action No response action is required. Category Configuration SubCategory SYS = System Info Severity Severity 3 (Informational) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default.
PAGE 816
Initial Default. FALSE Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE SYS004 Invalid parameter value forarg1. Message Arguments • arg1 = parameter name Detailed Description The value provided for the specified parameter is invalid.
PAGE 817
Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE SYS006 Unable to set read only attribute:arg1 Message Arguments • arg1 = attribute name Detailed Description The attribute being set is currently read-only and cannot be changed. Recommended Response Action Refer to the Lifecycle Controller Remote Services documentation for the specific attribute behavior.
PAGE 818
Initial Default. FALSE Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE SYS014 Invalid value for attribute:arg1 Message Arguments • arg1 = attribute name Detailed Description The value provided for the specified attribute is invalid.
PAGE 819
44 TMP Event Messages TMP8500 I/O Modulearg1temperature exceeded operating range. Message Arguments • arg1 = iom slot name Detailed Description The temperature of the I/O Module identified in the message has increased beyond the operational range. Thermal protection shut down the I/O Module. Factors external to the I/O Module may have caused this situation. Recommended Response Action Check the chassis event log for fan issues and fix any issues present.
PAGE 820
Severity Severity 2 (Warning) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default. LC Log Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE TRUE FALSE FALSE FALSE FALSE FALSE TMP8502 Message Able to read planar board temperature sensors. Cooling set for normal chassis operation.
PAGE 821
Category Storage SubCategory TMP = Temperature Severity Severity 2 (Warning) Trap/EventID 4210 LCD Message No LCD message display defined. Initial Default. SNMP Alert;#LCD;#Remote System Log Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset TRUE FALSE TRUE TRUE TRUE FALSE FALSE TRUE FALSE TMP1001 arg1has crossed the minimum warning threshold. Message Arguments • arg1 = tempsensor name Detailed Description The enclosure is too cold.
PAGE 822
Recommended Response Action Check for factors that may cause overheating. For example, verify that the enclosure fan is working. You should also check the thermostat settings and examine whether the enclosure is located near a heat source. Make sure the enclosure has enough ventilation and that the room temperature is not too hot. Refer to the enclosure documentation for more diagnostic information.
PAGE 823
Arguments • arg1 = Enclosure name Detailed Description You have changed the value for the maximum temperature probe warning threshold. This alert is provided for informational purposes. Recommended Response Action No response action is required. Category Storage SubCategory TMP = Temperature Severity Severity 3 (Informational) Trap/EventID 4211 LCD Message No LCD message display defined. Initial Default.
PAGE 824
TMP7 arg1has failed. Message Arguments • arg1 = Temp Sensor Name Detailed Description A device has been failed and the system is no longer functioning in optimal condition. Recommended Response Action Replace the device. Category Storage SubCategory TMP = Temperature Severity Severity 1 (Critical) Trap/EventID 4209 LCD Message No LCD message display defined. Initial Default.
PAGE 825
Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE TMP0201 CPUarg1temperature is less than the lower critical threshold. Message Arguments • arg1 = number Detailed Description System performance may be degraded. Recommended Response Action Check system operating environment.
PAGE 826
Initial Default. FALSE Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE TMP0203 CPUarg1temperature is greater than the upper critical threshold. Message Arguments • arg1 = number Detailed Description System performance may be degraded. Recommended Response Action Check system operating environment, fans, and heatsinks.
PAGE 827
LCD Message CPU temperature is outside of range. Check fans Initial Default. FALSE Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE TMP0205 CPUarg1temperature is within range. Message Arguments • arg1 = number Detailed Description None Recommended Response Action No response action is required.
PAGE 828
Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default. FALSE Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE TMP0101 The system boardarg1temperature is less than the lower critical threshold. Message Arguments • arg1 = name Detailed Description Ambient air temperature is too cool. Recommended Response Action Check system operating environment.
PAGE 829
Severity Severity 2 (Warning) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default. FALSE Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE TMP0103 The system boardarg1temperature is greater than the upper critical threshold. Message Arguments • arg1 = name Detailed Description Ambient air temperature is too warm or one or more fans may have failed.
PAGE 830
SubCategory TMP = Temperature Severity Severity 1 (Critical) Trap/EventID FALSE LCD Message System board temperature is outside of range Check Fans Initial Default. FALSE Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE TMP0105 The system boardarg1temperature is within range.
PAGE 831
Category System Health SubCategory TMP = Temperature Severity Severity 2 (Warning) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default. FALSE Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE TMP0107 The memory modulearg1temperature is less than the lower critical threshold.
PAGE 832
Recommended Response Action Check system operating environment and review event log for fan failures. Category System Health SubCategory TMP = Temperature Severity Severity 2 (Warning) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default.
PAGE 833
Detailed Description Ambient air temperature is too warm or cool. Recommended Response Action Check system operating environment and review event log for fan failures. Category System Health SubCategory TMP = Temperature Severity Severity 1 (Critical) Trap/EventID FALSE LCD Message Memory module temperature is outside of range. Check Fans Initial Default.
PAGE 834
Detailed Description Ambient air temperature is too cool. Recommended Response Action Check system operating environment. Category System Health SubCategory TMP = Temperature Severity Severity 2 (Warning) Trap/EventID 2162 LCD Message No LCD message display defined. Initial Default.
PAGE 835
Detailed Description Ambient air temperature is too warm or one or more fans may have failed. Recommended Response Action Check system operating environment and review event log for fan failures. Category System Health SubCategory TMP = Temperature Severity Severity 2 (Warning) Trap/EventID 2162 LCD Message No LCD message display defined. Initial Default.
PAGE 836
Detailed Description Ambient air temperature is too warm or cool. Recommended Response Action Check system operating environment and review event log for fan failures. Category System Health SubCategory TMP = Temperature Severity Severity 1 (Critical) Trap/EventID 2161 LCD Message The temperature is outside of range. Check Fans Initial Default.
PAGE 837
Detailed Description Ambient air temperature is too cool. Recommended Response Action Check system operating environment. Category System Health SubCategory TMP = Temperature Severity Severity 2 (Warning) Trap/EventID 2162 LCD Message No LCD message display defined. Initial Default.
PAGE 838
Category System Health SubCategory TMP = Temperature Severity Severity 2 (Warning) Trap/EventID 2162 LCD Message No LCD message display defined. Initial Default. LC Log Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset TRUE FALSE TRUE TRUE FALSE FALSE FALSE TRUE FALSE TMP0121 Message The system inlet temperature is greater than the upper critical threshold. Detailed Description Ambient air temperature is too warm.
PAGE 839
Trap/EventID 2161 LCD Message Inlet temperature is outside of range . Check environment Initial Default. LC Log Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset TRUE FALSE TRUE TRUE FALSE FALSE FALSE FALSE TRUE TMP0123 Message The system inlet temperature is within range. Detailed Description None Recommended Response Action Check system operating environment.
PAGE 840
Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE TMP0125 Message Disk drive bay temperature is less than the lower critical threshold. Detailed Description Ambient air temperature is too cool. Recommended Response Action Check system operating environment.
PAGE 841
TMP0127 Message Disk drive bay temperature is greater than the upper critical threshold. Detailed Description Ambient air temperature is too warm or one or more fans may have failed. Recommended Response Action Check system operating environment and review event log for fan failures. Category System Health SubCategory TMP = Temperature Severity Severity 1 (Critical) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default.
PAGE 842
Detailed Description None Recommended Response Action No response action is required. Category System Health SubCategory TMP = Temperature Severity Severity 3 (Informational) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default.
PAGE 843
Category System Health SubCategory TMP = Temperature Severity Severity 1 (Critical) Trap/EventID 2161 LCD Message No LCD message display defined. Initial Default. LC Log Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset TRUE FALSE TRUE TRUE FALSE FALSE FALSE TRUE FALSE TMP0132 Message The control panel temperature is greater than the upper warning threshold.
PAGE 844
Trap/EventID 2161 LCD Message No LCD message display defined. Initial Default. LC Log Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset TRUE FALSE TRUE TRUE FALSE FALSE FALSE TRUE FALSE TMP0134 Message The control panel temperature is outside of range. Detailed Description Ambient air temperature is too warm or cool. Recommended Response Action Check system operating environment and review event log for fan failures.
PAGE 845
Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset TRUE FALSE TRUE TRUE FALSE FALSE FALSE TRUE FALSE TMP0136 Message Insufficient system cooling detected, system is shutdown. Detailed Description More then the minimun number of fans have been removed or failed in the system. System will not start or will shutdown. Recommended Response Action Replace failed fans. Install minimun requires fans.
PAGE 846
PAGE 847
45 USR Event Messages USR8500 Excessive login failures fromarg1; blocked forarg2seconds. Message Arguments • • arg1 = IP address arg2 = number Detailed Description Multiple login attempts were unsuccessful from the identified IP address. After detecting this error condition, this IP address will be blocked from login for the duration specified in the message.
PAGE 848
SubCategory USR = User Tracking Severity Severity 3 (Informational) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default.
PAGE 849
Recommended Response Action Contact the administrator and ensure the username and password credentials used in the operation are correct. Category Audit SubCategory USR = User Tracking Severity Severity 3 (Informational) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default.
PAGE 850
Recommended Response Action No response action is required. Category Audit SubCategory USR = User Tracking Severity Severity 3 (Informational) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default.
PAGE 851
• arg4 = error nunber Detailed Description The login attempt with details specified in the message was not successful. Recommended Response Action Contact the administrator and ensure the username and password credentials used are correct. Retry the operation with valid credentials. Category Audit SubCategory USR = User Tracking Severity Severity 3 (Informational) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default.
PAGE 852
USR8509 Login was not successful (username=arg1, ip=arg2, error=0xarg3, type=arg4) Message Arguments • • • • arg1 = username arg2 = ip address arg3 = error no arg4 = error type Detailed Description The login attempt with details specified in the message was not successful. Recommended Response Action Contact the administrator and ensure the username and password credentials used are correct. Retry the operation with valid credentials.
PAGE 853
Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default.
PAGE 854
Detailed Description Successful login by Username identified in the message. Recommended Response Action Contact the administrator and ensure the username and password credentials used are correct. Retry the operation with valid credentials. Category Audit SubCategory USR = User Tracking Severity Severity 3 (Informational) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default.
PAGE 855
USR107 arg1operation was performed byarg2onarg3ofarg4. Message Arguments • • • • arg1 = Set/Invoke arg2 = username arg3 = methodname name or instance arg4 = class name Detailed Description The specified user has performed a set or invoke method operation on the iDRAC. The operation is either set on an instance of the class identified or an invocation of the identified method. Recommended Response Action No response action is required.
PAGE 856
PAGE 857
46 VDR Event Messages VDR97 Patrol Read corrected a media error onarg1. Message Arguments • arg1 = VD Name Detailed Description The Patrol Read task has encountered an error such as a bad disk block and remapped data to correct the error. Recommended Response Action No response action is required. Category Storage SubCategory VDR = Virtual Disk Severity Severity 3 (Informational) Trap/EventID 4355 LCD Message No LCD message display defined. Initial Default.
PAGE 858
Severity Severity 1 (Critical) Trap/EventID 4353 LCD Message No LCD message display defined. Initial Default. SNMP Alert;#LCD;#Remote System Log Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset TRUE FALSE TRUE TRUE TRUE FALSE FALSE TRUE FALSE VDR2 arg1returned to optimal state. Message Arguments • arg1 = virtual disk Detailed Description The virtual disk has returned to a healthy state and is working properly.
PAGE 859
SubCategory VDR = Virtual Disk Severity Severity 3 (Informational) Trap/EventID 4355 LCD Message No LCD message display defined. Initial Default. SNMP Alert;#LCD;#Remote System Log Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset TRUE FALSE TRUE TRUE TRUE FALSE FALSE TRUE FALSE VDR4 arg1was created. Message Arguments • arg1 = virtual disk Detailed Description This message is generated after a virtual disk was created on a controller.
PAGE 860
Recommended Response Action No response action is required. Category Storage SubCategory VDR = Virtual Disk Severity Severity 3 (Informational) Trap/EventID 4355 LCD Message No LCD message display defined. Initial Default. SNMP Alert;#LCD;#Remote System Log Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset TRUE FALSE TRUE TRUE TRUE FALSE FALSE FALSE TRUE VDR6 arg1configuration has changed.
PAGE 861
Detailed Description One or more physical disks included in the virtual disk have failed. If the virtual disk is nonredundant (does not use mirrored or parity data), then the failure of a single physical disk can cause the virtual disk to fail. If the virtual disk is redundant, then more physical disks have failed than you can rebuild using mirrored or parity information. Recommended Response Action Create a new virtual disk and restore from a backup.
PAGE 862
VDR9 arg1consistency check has started. Message Arguments • arg1 = virtual disk Detailed Description A consistency check operation on a virtual disk has started. Recommended Response Action No response action is required. Category Storage SubCategory VDR = Virtual Disk Severity Severity 3 (Informational) Trap/EventID 4355 LCD Message No LCD message display defined. Initial Default.
PAGE 863
Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset TRUE FALSE TRUE TRUE TRUE FALSE FALSE TRUE FALSE VDR11 arg1has started initializing. Message Arguments • arg1 = virtual disk Detailed Description This message is generated after initialization of a virtual disk starts. Recommended Response Action No response action is required.
PAGE 864
Initial Default. SNMP Alert;#LCD;#Remote System Log Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset TRUE FALSE TRUE TRUE TRUE FALSE FALSE FALSE TRUE VDR13 arg1rebuild has started. Message Arguments • arg1 = VD Name Detailed Description This alert is provided for informational purposes. Recommended Response Action No response action is required.
PAGE 865
LCD Message No LCD message display defined. Initial Default. SNMP Alert;#LCD;#Remote System Log Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset TRUE FALSE TRUE TRUE TRUE FALSE FALSE TRUE FALSE VDR15 Initialization ofarg1was cancelled. Message Arguments • arg1 = virtual disk Detailed Description The initialization operation could not be completed. This may be due to a user action or a physical disk failure.
PAGE 866
Severity Severity 1 (Critical) Trap/EventID 4353 LCD Message No LCD message display defined. Initial Default. SNMP Alert;#LCD;#Remote System Log Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset TRUE FALSE TRUE TRUE TRUE FALSE FALSE TRUE FALSE VDR17 arg1format failed. Message Arguments • arg1 = VD Name Detailed Description A physical disk included in the virtual disk failed. Recommended Response Action Replace the failed physical disk.
PAGE 867
Category Storage SubCategory VDR = Virtual Disk Severity Severity 1 (Critical) Trap/EventID 4353 LCD Message No LCD message display defined. Initial Default. SNMP Alert;#LCD;#Remote System Log Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset TRUE FALSE TRUE TRUE TRUE FALSE FALSE TRUE FALSE VDR19 Reconfiguration ofarg1has failed.
PAGE 868
Recommended Response Action Replace the failed or corrupt disk. You can identify a disk that has failed by locating the disk that has a red "X" for its status. Restart the virtual disk rebuild. Category Storage SubCategory VDR = Virtual Disk Severity Severity 1 (Critical) Trap/EventID 4353 LCD Message No LCD message display defined. Initial Default.
PAGE 869
Detailed Description This alert is provided for informational purposes. Recommended Response Action No response action is required. Category Storage SubCategory VDR = Virtual Disk Severity Severity 3 (Informational) Trap/EventID 4355 LCD Message No LCD message display defined. Initial Default.
PAGE 870
Detailed Description The re-configuration operation on the virtual disk completed. Recommended Response Action No response action is required. Category Storage SubCategory VDR = Virtual Disk Severity Severity 3 (Informational) Trap/EventID 4355 LCD Message No LCD message display defined. Initial Default.
PAGE 871
Detailed Description You paused the Check Consistency operation on a virtual disk. Recommended Response Action To resume the Check Consistency operation, right-click the virtual disk in the Storage Management tree view and select Resume Check Consistency. Category Storage SubCategory VDR = Virtual Disk Severity Severity 3 (Informational) Trap/EventID 4355 LCD Message No LCD message display defined. Initial Default.
PAGE 872
Detailed Description A user has caused a mirrored virtual disk to be split. When a virtual disk is mirrored, its data is copied to another virtual disk to maintain redundancy. After being split, both virtual disks retain a copy of the data. Because the mirror is no longer intact, updates to the data are no longer copied to the mirror. Recommended Response Action This alert is provided for informational purposes.
PAGE 873
Arguments • arg1 = virtual disk Detailed Description A user changed the write policy for a virtual disk. Recommended Response Action This alert is provided for informational purposes. Category Storage SubCategory VDR = Virtual Disk Severity Severity 3 (Informational) Trap/EventID 4355 LCD Message No LCD message display defined. Initial Default.
PAGE 874
VDR32 Background initialization has started forarg1. Message Arguments • arg1 = virtual disk Detailed Description Background initialization of a virtual disk has started. This is an automated process that writes the parity or mirror data on newly created virtual disks. Recommended Response Action No response action is required. Category Storage SubCategory VDR = Virtual Disk Severity Severity 3 (Informational) Trap/EventID 4355 LCD Message No LCD message display defined. Initial Default.
PAGE 875
Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset TRUE FALSE TRUE TRUE TRUE FALSE FALSE TRUE FALSE VDR34 Background initialization failed forarg1. Message Arguments • arg1 = virtual disk Detailed Description Background initialization of a virtual disk failed. Recommended Response Action Run a consistency check on the virtual disk. If that fails, check the health of the member drives of the virtual disk and then recreate.
PAGE 876
Initial Default. SNMP Alert;#LCD;#Remote System Log Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset TRUE FALSE TRUE TRUE TRUE FALSE FALSE TRUE FALSE VDR36 arg1initialization is in-progressarg2. Message Arguments • • arg1 = VD Name arg2 = progresspercent Detailed Description Virtual disk initialization is in-progress. This alert is provided for informational purposes. Recommended Response Action No response action is required.
PAGE 877
Trap/EventID 4355 LCD Message No LCD message display defined. Initial Default. SNMP Alert;#LCD;#Remote System Log Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset TRUE FALSE TRUE TRUE TRUE FALSE FALSE TRUE FALSE VDR38 arg1is renamed. Message Arguments • arg1 = VD Name Detailed Description A user renamed a virtual disk. This alert is provided for informational purposes. Recommended Response Action No response action is required.
PAGE 878
SubCategory VDR = Virtual Disk Severity Severity 3 (Informational) Trap/EventID 4355 LCD Message No LCD message display defined. Initial Default. SNMP Alert;#LCD;#Remote System Log Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset TRUE FALSE TRUE TRUE TRUE FALSE FALSE TRUE FALSE VDR40 The reconfiguration ofarg1has resumed.
PAGE 879
Category Storage SubCategory VDR = Virtual Disk Severity Severity 3 (Informational) Trap/EventID 4355 LCD Message No LCD message display defined. Initial Default. SNMP Alert;#LCD;#Remote System Log Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset TRUE FALSE TRUE TRUE TRUE FALSE FALSE FALSE TRUE VDR42 Dedicated hot spare assigned physical diskarg1.
PAGE 880
Recommended Response Action No response action is required. Category Storage SubCategory VDR = Virtual Disk Severity Severity 3 (Informational) Trap/EventID 4355 LCD Message No LCD message display defined. Initial Default. SNMP Alert;#LCD;#Remote System Log Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset TRUE FALSE TRUE TRUE TRUE FALSE FALSE FALSE TRUE VDR44 arg1disk cache policy has changed.
PAGE 881
Detailed Description This alert is provided for informational purposes. Recommended Response Action No response action is required. Category Storage SubCategory VDR = Virtual Disk Severity Severity 3 (Informational) Trap/EventID 4355 LCD Message No LCD message display defined. Initial Default.
PAGE 882
Detailed Description A disk media error was detected while the controller was completing a background task. A bad disk block was identified. The disk block was remapped. Recommended Response Action Check the Lifecycle log for information related to members of this virtual disk. Category Storage SubCategory VDR = Virtual Disk Severity Severity 3 (Informational) Trap/EventID 4355 LCD Message No LCD message display defined. Initial Default.
PAGE 883
Arguments • arg1 = VD Name Detailed Description A redundant virtual disk has lost redundancy. This may occur when the virtual disk suffers the failure of more than one physical disk. In this case, both the source physical disk and the target disk with redundant data have failed. A rebuild is not possible because there is no longer redundancy. Recommended Response Action Replace the failed disks and restore from backup.
PAGE 884
Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset TRUE FALSE TRUE TRUE TRUE FALSE FALSE TRUE FALSE VDR51 The consistency check process made corrections and completed onarg1. Message Arguments • arg1 = virtual disk Detailed Description The consistency check completed on the virtual disk after making corrections. Recommended Response Action No response action is required.
PAGE 885
Trap/EventID 4354 LCD Message No LCD message display defined. Initial Default. SNMP Alert;#LCD;#Remote System Log Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset TRUE FALSE TRUE TRUE TRUE FALSE FALSE TRUE FALSE VDR53 The consistency check logging of inconsistent parity data is disabled forarg1. Message Arguments • arg1 = virtual disk Detailed Description The consistency check can no longer report errors in the parity data.
PAGE 886
Severity Severity 2 (Warning) Trap/EventID 4354 LCD Message No LCD message display defined. Initial Default. SNMP Alert;#LCD;#Remote System Log Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset TRUE FALSE TRUE TRUE TRUE FALSE FALSE TRUE FALSE VDR55 arg1initialization has failed. Message Arguments • arg1 = VD Name Detailed Description The controller cannot communicate with attached devices. A disk may be removed or contain errors.
PAGE 887
Recommended Response Action Replace the missing or failed physical disk. Category Storage SubCategory VDR = Virtual Disk Severity Severity 3 (Informational) Trap/EventID 4355 LCD Message No LCD message display defined. Initial Default.
PAGE 888
Detailed Description This message occurs if there are medium errors in the physical drives. Recommended Response Action Replace the failed drives. Category Storage SubCategory VDR = Virtual Disk Severity Severity 1 (Critical) Trap/EventID 4353 LCD Message No LCD message display defined. Initial Default.
PAGE 889
Detailed Description This alert message occurs if there are medium errors in the physical drives. Recommended Response Action No response action is required. Category Storage SubCategory VDR = Virtual Disk Severity Severity 3 (Informational) Trap/EventID 4355 LCD Message No LCD message display defined. Initial Default.
PAGE 890
• arg2 = VD Name Detailed Description This alert message occurs if the virtual disk has bad blocks. Recommended Response Action Replace the disk in the Virtual disk, generating this alert and restore from backup. You may have lost data. Category Storage SubCategory VDR = Virtual Disk Severity Severity 3 (Informational) Trap/EventID 4355 LCD Message No LCD message display defined. Initial Default.
PAGE 891
Arguments • • arg1 = args arg2 = VD Name Detailed Description Virtual disk bad blocks are due to presence of unrecoverable bad blocks on one or more member physical disks. Recommended Response Action Recovering a physical disk bad block depends on the RAID level and state of the virtual disk. If a virtual disk is redundant, the controller can recover a bad block on a physical disk. If a virtual disk is not redundant, then the physical disk bad block results in a virtual disk bad block.
PAGE 892
PAGE 893
47 VFL Event Messages VFL1001 Removable Flash Mediaarg1is present. Message Arguments • arg1 = name Detailed Description None Recommended Response Action No response action is required. Category System Health SubCategory VFL = vFlash Event Severity Severity 3 (Informational) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default.
PAGE 894
Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default. FALSE Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE VFL1003 Removable Flash Mediaarg1is not IPMI-function ready. Message Arguments • arg1 = name Detailed Description The removable flash media is installed but improperly configured or failed to initialize.
PAGE 895
Severity Severity 3 (Informational) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default. FALSE Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE VFL1005 Removable Flash Mediaarg1is not ready. Message Arguments • arg1 = name Detailed Description The media is being prepared or is under maintenance. If the problem persists, reinstall the card.
PAGE 896
SubCategory VFL = vFlash Event Severity Severity 2 (Warning) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default. FALSE Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE VFL1007 Removable Flash Mediaarg1is online. Message Arguments • arg1 = name Detailed Description None Recommended Response Action No response action is required.
PAGE 897
Category System Health SubCategory VFL = vFlash Event Severity Severity 1 (Critical) Trap/EventID FALSE LCD Message Removable Flash Media failed. Check SD Card Initial Default. FALSE Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE VFL1009 Removable Flash Mediaarg1is operating normally.
PAGE 898
Recommended Response Action No response action is required. Category System Health SubCategory VFL = vFlash Event Severity Severity 3 (Informational) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default. FALSE Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE VFL1011 Removable Flash Mediaarg1was deactivated.
PAGE 899
Detailed Description None Recommended Response Action No response action is required. Category System Health SubCategory VFL = vFlash Event Severity Severity 3 (Informational) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default. FALSE Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE VFL1013 Removable Flash Mediaarg1has finished booting.
PAGE 900
Detailed Description The card is write-protected by the physical latch on the SD card. IDSDM cannot use a writeprotected card. Recommended Response Action if unintended, remove the media and disable write protection. Category System Health SubCategory VFL = vFlash Event Severity Severity 2 (Warning) Trap/EventID FALSE LCD Message Removable Flash Media is write protected. Check SD Card Initial Default.
PAGE 901
Detailed Description The SD card is not detected or not installed. Recommended Response Action If unintended, reinstall the flash media. Category System Health SubCategory VFL = vFlash Event Severity Severity 1 (Critical) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default.
PAGE 902
PAGE 903
48 VFLA Event Messages VFLA1000 Removable Flash Mediaarg1is absent. Message Arguments • arg1 = name Detailed Description None Recommended Response Action No response action is required. Category System Health SubCategory VFLA = vFlash Absent Severity Severity 3 (Informational) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default.
PAGE 904
PAGE 905
49 VLT Event Messages VLT0300 CPUarg1arg2voltage is less than the lower warning threshold. Message Arguments • • arg1 = number arg2 = name Detailed Description Low voltages may be the result of a problem with the voltage regulator or a problem with the processor. The low voltage may cause the processor to fail to operate. Recommended Response Action 1) Turn system off and remove input power for one minute. Re-apply input power and turn system on. 2) Make sure the processor is seated correctly.
PAGE 906
Category System Health SubCategory VLT = Voltage Severity Severity 1 (Critical) Trap/EventID FALSE LCD Message CPU voltage is outside of range. Reseat CPU Initial Default. FALSE Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE VLT0302 CPUarg1arg2voltage is greater than the upper warning threshold.
PAGE 907
Detailed Description High voltages may be the result of problem with the voltage regulator or a problem with the processor. Elevated voltages may result in damage to the processor or other system electrical components. The system may power down. Recommended Response Action 1) Turn system off and remove input power for one minute. Re-apply input power and turn system on. 2) Make sure the processor is seated correctly. 3) If the issue still persists, contact technical support.
PAGE 908
VLT0305 CPUarg1arg2voltage is within range. Message Arguments • • arg1 = number arg2 = name Detailed Description None Recommended Response Action No response action is required. Category System Health SubCategory VLT = Voltage Severity Severity 3 (Informational) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default.
PAGE 909
Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset TRUE FALSE TRUE TRUE FALSE FALSE FALSE TRUE FALSE VLT0201 The system boardarg1voltage is less than the lower critical threshold. Message Arguments • arg1 = name Detailed Description System hardware detected an over voltage or under voltage condition. If multiple voltage exceptions occur consecutively the system may power down in failsafe mode.
PAGE 910
LCD Message No LCD message display defined. Initial Default. LC Log Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset TRUE FALSE TRUE TRUE FALSE FALSE FALSE TRUE FALSE VLT0203 The system boardarg1voltage is greater than the upper critical threshold. Message Arguments • arg1 = name Detailed Description System hardware detected an over voltage or under voltage condition.
PAGE 911
Severity Severity 1 (Critical) Trap/EventID 2169 LCD Message System board voltage is outside of range. Contact support Initial Default. LC Log Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset TRUE FALSE TRUE TRUE FALSE FALSE FALSE FALSE TRUE VLT0205 The system boardarg1voltage is within range. Message Arguments • arg1 = name Detailed Description None Recommended Response Action No response action is required.
PAGE 912
Category System Health SubCategory VLT = Voltage Severity Severity 2 (Warning) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default. FALSE Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE VLT0207 The memory modulearg1arg2voltage is less than the lower critical threshold.
PAGE 913
Detailed Description System hardware detected an over voltage or under voltage condition. If multiple voltage exceptions occur consecutively the system may power down in failsafe mode. Recommended Response Action 1) Review system logs for power supply exceptions. 2) Reseat the memory module. 3) If the problem persists, contact technical support. Refer to the product documentation to choose a convenient contact method.
PAGE 914
VLT0210 The memory modulearg1arg2voltage is outside of range. Message Arguments • • arg1 = number arg2 = name Detailed Description System hardware detected an over voltage or under voltage condition. If multiple voltage exceptions occur consecutively the system may power down in failsafe mode. Recommended Response Action 1) Review system logs for power supply exceptions. 2) Reseat the memory module. 3) If the problem persists, contact technical support.
PAGE 915
Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE VLT0212 The disk drive bayarg1voltage is less than the lower warning threshold. Message Arguments • arg1 = name Detailed Description System hardware detected an over voltage or under voltage condition. If multiple voltage exceptions occur consecutively the system may power down in failsafe mode.
PAGE 916
LCD Message No LCD message display defined. Initial Default. FALSE Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE VLT0214 The disk drive bayarg1voltage is greater than the upper warning threshold. Message Arguments • arg1 = name Detailed Description System hardware detected an over voltage or under voltage condition.
PAGE 917
Severity Severity 1 (Critical) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default. FALSE Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE VLT0216 The disk drive bayarg1voltage is outside of range. Message Arguments • arg1 = name Detailed Description System hardware detected an over voltage or under voltage condition.
PAGE 918
Category System Health SubCategory VLT = Voltage Severity Severity 3 (Informational) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default. FALSE Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE VLT0218 Thearg1voltage is less than the lower warning threshold.
PAGE 919
Recommended Response Action 1) Review system logs for power supply exceptions 2) Reduce system to minimum configuration, inspect and re-install system cables. 3) If the problem persists, contact technical support. Refer to the product documentation to choose a convenient contact method. Category System Health SubCategory VLT = Voltage Severity Severity 1 (Critical) Trap/EventID 2169 LCD Message The voltage is outside of range. Contact support Initial Default.
PAGE 920
Detailed Description System hardware detected an over voltage or under voltage condition. If multiple voltage exceptions occur consecutively the system may power down in failsafe mode. Recommended Response Action 1) Review system logs for power supply exceptions 2) Reduce system to minimum configuration, inspect and re-install system cables. 3) If the problem persists, contact technical support. Refer to the product documentation to choose a convenient contact method.
PAGE 921
Arguments • arg1 = name Detailed Description None Recommended Response Action No response action is required. Category System Health SubCategory VLT = Voltage Severity Severity 3 (Informational) Trap/EventID 2171 LCD Message No LCD message display defined. Initial Default.
PAGE 922
VLT0101 Processor modulearg1voltage is less than the lower critical threshold. Message Arguments • arg1 = name Detailed Description System hardware detected an over voltage or under voltage condition. If multiple voltage exceptions occur consecutively the system may power down in failsafe mode. Recommended Response Action 1) Review system logs for power supply exceptions. 2) Remove the processor module. Inspect processor socket for bent pins. 3) If the problem persists, contact technical support.
PAGE 923
Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE VLT0103 Processor modulearg1voltage is greater than the upper critical threshold. Message Arguments • arg1 = name Detailed Description System hardware detected an over voltage or under voltage condition. If multiple voltage exceptions occur consecutively the system may power down in failsafe mode.
PAGE 924
LCD Message Processor module voltage is outside of range. Contact support Initial Default. FALSE Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE VLT0105 Processor modulearg1voltage is within range. Message Arguments • arg1 = name Detailed Description None Recommended Response Action No response action is required.
PAGE 925
Severity Severity 2 (Warning) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default. FALSE Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE VLT0225 The memory modulearg1voltage is less than the lower critical threshold. Message Arguments • arg1 = name Detailed Description System hardware detected an over voltage or under voltage condition.
PAGE 926
Category System Health SubCategory VLT = Voltage Severity Severity 2 (Warning) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default. FALSE Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE VLT0227 The memory modulearg1voltage is greater than the upper critical threshold.
PAGE 927
Recommended Response Action 1) Review system logs for power supply exceptions. 2) Reseat the memory module. 3) If the problem persists, contact technical support. Refer to the product documentation to choose a convenient contact method. Category System Health SubCategory VLT = Voltage Severity Severity 1 (Critical) Trap/EventID FALSE LCD Message Memory module voltage is outside of range. Contact support Initial Default.
PAGE 928
Detailed Description System hardware detected an over voltage or under voltage condition. If multiple voltage exceptions occur consecutively the system may power down in failsafe mode. Recommended Response Action 1) Review system logs for power supply exceptions. 2) Reseat the mezzanine card. 3) If the problem persists, contact technical support. Refer to the product documentation to choose a convenient contact method.
PAGE 929
VLT0232 The mezzanine cardarg1arg2voltage is greater than the upper warning threshold. Message Arguments • • arg1 = number arg2 = name Detailed Description System hardware detected an over voltage or under voltage condition. If multiple voltage exceptions occur consecutively the system may power down in failsafe mode. Recommended Response Action 1) Review system logs for power supply exceptions. 2) Reseat the mezzanine card. 3) If the problem persists, contact technical support.
PAGE 930
Initial Default. FALSE Filter Visibility IPMI Alert SNMP Alert Email Alert LC Log LCD Power Off Power Cycle Reset FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE VLT0234 The mezzanine cardarg1arg2voltage is outside of range. Message Arguments • • arg1 = number arg2 = name Detailed Description System hardware detected an over voltage or under voltage condition. If multiple voltage exceptions occur consecutively the system may power down in failsafe mode.
PAGE 931
Severity Severity 3 (Informational) Trap/EventID FALSE LCD Message No LCD message display defined. Initial Default.