Users Guide

Configuration de Linux pour la redirection de la console série du serveur
après l'amorçage
Modifiez le fichier /etc/inittab de la manière suivante :
Ajoutez une nouvelle ligne pour configurer agetty sur le port série COM2 :
co:2345:respawn:/sbin/agetty -h -L 57600 ttyS1 ansi
L'exemple suivant montre le fichier avec la nouvelle ligne.
# # inittab This file describes how the INIT process # should set up the system
in a certain # run-level. # # Author: Miquel van Smoorenburg # Modified for RHS
Linux by Marc Ewing and # Donnie Barnes # # Default runlevel. The runlevels
used by RHS are: # 0 - halt (Do NOT set initdefault to this) # 1 - Single user
mode # 2 - Multiuser, without NFS (The same as 3, if you # do not have
networking) # 3 - Full multiuser mode # 4 - unused # 5 - X11 # 6 - reboot (Do
NOT set initdefault to this) # id:3:initdefault: # System initialization.
si::sysinit:/etc/rc.d/rc.sysinit l0:0:wait:/etc/rc.d/rc 0 l1:1:wait:/etc/
rc.d/rc 1 l2:2:wait:/etc/rc.d/rc 2 l3:3:wait:/etc/rc.d/rc 3 l4:4:wait:/etc/
rc.d/rc 4 l5:5:wait:/etc/rc.d/rc 5 l6:6:wait:/etc/rc.d/rc 6 # Things to run in
every runlevel. ud::once:/sbin/update # Trap CTRL-ALT-DELETE ca::ctrlaltdel:/
sbin/shutdown -t3 -r now # When our UPS tells us power has failed, assume we
have a few # minutes of power left. Schedule a shutdown for 2 minutes from now.
# This does, of course, assume you have power installed and your # UPS is
connected and working correctly. pf::powerfail:/sbin/shutdown -f -h +2 "Power
Failure; System Shutting Down" # If power was restored before the shutdown
kicked in, cancel it. pr:12345:powerokwait:/sbin/shutdown -c "Power Restored;
Shutdown Cancelled" # Run gettys in standard runlevels
co:2345:respawn:/sbin/
agetty -h -L 57600 ttyS1 ansi 1:2345:respawn:/sbin/mingetty tty1
2:2345:respawn:/sbin/mingetty tty2 3:2345:respawn:/sbin/mingetty tty3
4:2345:respawn:/sbin/mingetty tty4 5:2345:respawn:/sbin/mingetty tty5
6:2345:respawn:/sbin/mingetty tty6 # Exécutez xdm pour le niveau d'exécution 5
# xdm est désormais un service séparé x:5:respawn:/etc/X11/prefdm -nodaemon
Modifiez le fichier /etc/securetty de la manière suivante :
Ajoutez une nouvelle ligne avec le nom du tty série de COM2 :
ttyS1
L'exemple suivant montre un fichier avec la nouvelle ligne.
vc/1 vc/2 vc/3 vc/4 vc/5 vc/6 vc/7 vc/8 vc/9 vc/10 vc/11 tty1 tty2 tty3 tty4
tty5 tty6 tty7 tty8 tty9 tty10 tty11 ttyS1
Gestion de CMC à l’aide de proxy RACADM d'iDRAC
Le CMC peut être géré à l’aide d'un proxy RACADM d’iDRAC lorsque le CMC n’est pas sur le réseau. Le
tableau suivant énumère les mappages de privilèges CMC avec les privilèges iDRAC pour l’opération de
proxy.
Privilèges CMC Privilège iDRAC requis pour l’opération de proxy
Ouverture de session utilisateur CMC Connexion iDRAC
Administrateur de configuration du châssis Configurer iDRAC
142