Chassis Management Controller Version 1.
Anmerkungen, Vorsichtshinweise und Warnungen ANMERKUNG: Eine ANMERKUNG liefert wichtige Informationen, mit denen Sie den Computer besser einsetzen können. VORSICHT: Ein VORSICHTSHINWEIS macht darauf aufmerksam, dass bei Nichtbefolgung von Anweisungen eine Beschädigung der Hardware oder ein Verlust von Daten droht, und zeigt auf, wie derartige Probleme vermieden werden können.
Inhaltsverzeichnis 1 Übersicht................................................................................................................... 15 Was ist neu in dieser Version?.............................................................................................................16 Wichtige Funktionen........................................................................................................................... 16 Verwaltungsfunktionen......................................................
CMC-Netzwerk anfänglich konfigurieren.................................................................................... 36 Schnittstellen und Protokoll für den Zugriff auf CMC.......................................................................40 Starten von CMC mit anderen Systems Management Tools...................................................... 42 Herunterladen und Aktualisieren der CMC-Firmware.......................................................................
Ändern des standardmäßigen Anmeldekennworts unter Verwendung von WebSchnittstelle................................................................................................................................... 56 Ändern eines in den Standardeinstellungen festgelegten Anmeldungskennworts unter Verwendung von RACADM........................................................................................................... 57 Aktivieren oder Deaktivieren der standardmäßigen Kennwortwarnungsmeldung ..........
5 Gehäuseinformationen anzeigen und Funktionszustandsüberwachung von Gehäuse und individuellen Komponenten............................................................................................................. 77 Gehäuse- und Komponenten-Zusammenfassungen anzeigen........................................................77 Gehäuse-Grafiken......................................................................................................................... 78 Ausgewählte Komponenteninformationen......
Dienste konfigurieren......................................................................................................................... 94 Dienste unter Verwendung der CMC-Webschnittstelle konfigurieren.......................................95 Dienste über RACADM konfigurieren........................................................................................... 95 Erweiterte CMC-Speicherkarte konfigurieren...................................................................................
Remote-Dateifreigabe konfigurieren................................................................................................117 Konfiguration von Profileinstellungen durch das Replizieren von Serverkonfigurationen.............118 Zugriff auf die Seite Serverprofile................................................................................................119 Hinzufügen oder Speichern eines Profils...................................................................................
10 CMC für die einfache Anmeldung oder Smart Card-Anmeldung konfigurieren.............................................................................................................159 Systemanforderungen.......................................................................................................................159 Client-Systeme............................................................................................................................160 CMC.......................................
Anzeige von FlexAddress-Informationen................................................................................... 181 Anzeigen der FlexAddress-Gehäuseinformationen................................................................... 182 Anzeigen von FlexAddress-Informationen für alle Server......................................................... 182 Anzeige der FlexAddress Informationen für einzelne Server.....................................................183 FlexAddress konfigurieren...............
Regel zur Zuschaltung neuer Server.......................................................................................... 203 Netzteil- und Redundanzregeländerungen im Systemereignisprotokoll.................................205 Strombudget und Redundanz konfigurieren...................................................................................205 Stromeinsparung und Strombudget.......................................................................................... 206 Maximaler Stromsparmodus.....
Globalen Hotspare unter Verwendung von RACADM zuweisen.................................................... 221 Wiederherstellung von physischen Festplatten............................................................................... 221 Eigenschaften von virtuellen Festplatten unter Verwendung der CMC-Webschnittstelle anzeigen............................................................................................................................................
Fehlerbehebung bei Netzwerkproblemen.......................................................................................242 Fehlerbehebung: Controller.............................................................................................................243 18 LCD-Schnittstelle verwenden.........................................................................245 LCD-Navigation............................................................................................................................
Übersicht 1 Der Dell Chassis Management Controller (CMC) für Dell PowerEdge VRTX ist eine SystemverwaltungsHardware- und -Software-Lösung zur Verwaltung der PowerEdge VRTX-Gehäuse. Der CMC verfügt über einen eigenen Mikroprozessor und Speicher und wird vom modularen Gehäuse, an das er angeschlossen ist, mit Strom versorgt.
– Einstellungen der Stromredundanz und der Obergrenze für den Stromverbrauch. – E/A-Switches und iDRAC-Netzwerkeinstellungen. – Das erste Startgerät auf den Serverblades. – Übereinstimmungsprüfungen der E/A-Struktur zwischen den E/A-Modulen und Servern. CMC deaktiviert auch wenn notwendig Komponente, um die Systemhardware zu schützen. – Sicherheitsmerkmale für den Benutzerzugriff. – Speicherkomponenten, einschließlich des Fehlertoleranzmodus für den Speicher-Controller. – PCIe-Steckplätze.
• • • • • • • • • • • • • • • • Remote-Stromverwaltung – Bietet Remote-Stromverwaltungsfunktionen wie z. B. Ausschalten und Reset einer beliebigen Gehäusekomponente von einer Verwaltungskonsole aus. Stromverbrauchsberichte. SSL-Verschlüsselung (Secure Sockets Layer) – Bietet sichere Remote-Systemverwaltung über die Webschnittstelle. Startpunkt für die Web-Schnittstelle des Integrated Dell Remote Access Controller (iDRAC). Unterstützung für WS-Management.
Element Anzeige, Taste oder Anschluss 1 Status-/Identifikationsanzeiger (CMC 1) 2 Stromanzeiger (CMC 1) 3 CMC-Verbindungsschnitstellen (2) 4 Stromanzeiger (CMC 2) 5 Status-/Identifikationsanzeiger (CMC 2) Hier wird eine Rückansicht des Gehäuses mit einer Tabelle angezeigt, die die Teile und Geräte, die im CMC verfügbar sind, auflistet.
Element Anzeige, Taste oder Anschluss 1 PCIe-Erweiterungskartensteckplätze (niedriges Profil) (5) 2 PCIe-Erweiterungskartensteckplätze mit voller Bauhöhe (3) 3 CMC GB Ethernet-Port (CMC-2) 4 CMC GB Ethernet-Port (CMC-1) 5 Serieller Konnektor 6 Lüftermodule (4) 7 E/A-Modulschnittstellen 8 Netzteil 4 9 Netzteil 3 10 Netzteil 1 11 Netzteil 2 Hier wird eine Vorderansicht des Gehäuses mit einer Tabelle angezeigt, die die Teile und Geräte, die im CMC verfügbar sind, auflistet.
Abbildung 1. Merkmale und Anzeigen auf der Vorderseite – Gehäuse für 3,5-Zoll-Festplattenlaufwerke Ele me nt Anzeige, Taste oder Anschluss Beschreibung 1 USB-Anschlüsse (2) Ermöglichen das Anschließen von Tastatur und Maus am System. 2 LCD-Display Zeigt Systeminformationen sowie Status- und Fehlermeldungen an, die darüber informieren, ob das System ordnungsgemäß funktioniert oder überprüft werden muss. 3 LCD-Menü Scrolltasten (4) Bewegt den Cursor schrittweise vorwärts.
Ele me nt Anzeige, Taste oder Anschluss Beschreibung 3,5-ZollFestplattenlauf werksgehäuse Bis zu zwölf hot-swap-fähige 3,5-ZollFestplattenlaufwerke. 7 Informationsbereich Ein ausziehbares Etikettenfeld, auf dem Sie nach Bedarf Systeminformationen wie die Service-Tag-Nummer, NIC, MACAdresse, Angaben zum elektrischen Verbrauch des Systems und Markierungen der Worldwide-Zulassungsbehörde verzeichnen können.
Unterstützte Plattformen Der CMC unterstützt modulare Server, die für die PowerEdge VRTX-Plattform vorgesehen sind. Informationen über die Kompatibilität des CMC finden Sie in der Dokumentation Ihres Geräts. Informationen über aktuell unterstützte Betriebssysteme finden Sie in den Dell Chassis Management Controller (CMC) Version 1.00 for Dell PowerEdge VRTX Release Notes (Dell Chassis Management Controller (CMC) Version 1.00 für Dell PowerEdge VRTX Versionshinweisen), verfügbar unter dell.
• Selbstbedienungs-Portal – In CMC wird ein Link zum Selbstbedienungs-Portal angezeigt. Klicken Sie auf diesen Link, um das internetbasierte Selbstbedienungs-Portal für die Lizenzierung aufzurufen. Hier können Sie die gewünschten Lizenzen erwerben. Weitere Informationen finden Sie in der Online-Hilfe für das Selbstbedienungs-Portal. • Point-of-sale – Die Lizenz wird im Rahmen der Systembestellung angefordert.
Lizenz/ Komponente NichtAdministratorAnmeldung Ja Nein Nein Nein Ja Aktive Lizenz Ja Ja Ja Ja Ja Abgelaufene Lizenz Nein Ja Ja Ja Ja Lizenz installiert, jedoch fehlt Komponente Nein Ja Ja Nein Ja Lizenzen über die CMC-Webschnittstelle verwalten Um Lizenzen über die iDRAC7-Webschnittstelle zu verwalten, gehen Sie zu Gehäuseübersicht → Setup → Lizenzen. Stellen Sie vor dem Importieren einer Lizenz sicher, dass Sie eine gültige Lizenzdatei auf dem lokalen System bzw.
RACADM (SSH, Lokal und Remote) Ja Ja CMC-Setup-Backup Nein Ja CMC-SetupWiederherstellung Ja Ja WS-MAN Ja Ja SNMP Ja Ja Telnet Ja Ja SSH Ja Ja Internet-basierte Schnittstelle Ja Ja E-Mail-Warnungen Ja Ja LCD-Bereitstellung Ja Ja Erweiterte iDRACVerwaltung Ja Ja Remote-Syslog Nein Ja Verzeichnisdienste Nein* Ja Einfache iDRACAnmeldung Nein Ja ZweifaktorAuthentifizierung Nein Ja PK-Authentifizierung Nein Ja Remote-Dateifreigabe Ja Ja Steckplatz-ResourcenVerwal
Dynamische NetzteilEinsatzfähigkeit Nein* Ja Verwaltung von mehreren Gehäusen Nein Ja Erweiterte Konfiguration Nein Ja Gehäuse-EbenenBackup Ja Nein *Für Nicht-Standard-DPSE-Einstellungen ist nur „DPSE zurücksetzen“ mit einer Express-Lizenz erlaubt. „DPSE zurücksetzen“ setzt DPSE auf die Werkseinstellungen zurück. FlexAddress-Aktivierung Nein* Ja *Für Nicht-Standard-FlexAddress-Einstellungen ist nur „Standardeinstellung zurücksetzen“ mit der Express-Lizenz erlaubt.
Verwendung dieses Benutzerhandbuchs Der Inhalt dieses Benutzerhandbuchs ermöglicht es Ihnen, die Tasks auszuführen, indem Sie Folgendes verwenden: • Die Webschnittstelle: Hier erhalten Sie nur Informationen in Beziehung zu Tasks. Informationen über die Felder und Optionen finden Sie unter der CMC for Dell PowerEdge VRTX Online Help (CMC für Dell PowerEdge VRTX Online-Hilfe), die Sie von der Webschnittstelle aus öffnen können.
• Das Dell PowerEdge VRTX Getting Started Guide – Dell PowerEdge VRTX-Handbuch zum Einstieg), das mit Ihrem System geliefert wurde, enthält eine Übersicht über die Systemfunktionen, die Einrichtung des Systems und technische Daten. • Das Setup-Platzset, das mit Ihrem System geliefert wurde, enthält Informationen über die Systemersteinrichtung und Konfiguration.
* Client-Systemverwaltung * Unternehmens-Systemverwaltung * Unternehmens-Remote-Systemverwaltung * Tools für die Betriebsfähigkeit – Klicken Sie zur Anzeige des Dokuments auf die benötigte Produktversion. • Verwenden von Suchmaschinen wie folgt: – Geben Sie den Namen und die Version des Dokuments in das Kästchen Suchen ein.
Installation und Setup des CMC 2 Dieser Abschnitt enthält Informationen darüber, wie die CMC-Hardware installiert, der Zugriff auf den CMC eingerichtet und die Verwaltungsumgebung zur Verwendung des CMC konfiguriert wird und führt Sie durch die Tasks zum Konfigurieren eines CMC: • Anfänglichen Zugriff auf den CMC einrichten. • Über ein Netzwerk auf den CMC zugreifen. • CMC-Benutzer hinzufügen und konfigurieren.
7. Stellen Sie unter Verwendung des Webbrowsers eine Verbindung mit der CMC-IP-Adresse her, indem Sie den Standardbenutzernamen (root) und das Kennwort (calvin) verwenden. 8. Geben Sie jedem iDRAC eine IP-Adresse in der CMC-Webschnittstelle und aktivieren Sie die LANund IPMI-Schnittstelle. ANMERKUNG: Auf manchen Servern ist die iDRAC-LAN-Schnittstelle standardmäßig deaktiviert. Diese Information kann auf der CMC-Webschnittstelle unter Server-Übersicht → Setup gefunden werden.
3. Um die DVD am erforderlichen Standort bereitzustellen, verwenden Sie den Befehl mount oder einen ähnlichen Befehl. ANMERKUNG: Auf dem Red Hat Enterprise Linux 5-Betriebssystem werden DVDs automatisch mit der Ladeoption -noexec mount geladen. Diese Option erlaubt Ihnen nicht, beliebige ausführbare Datei von der DVD auszuführen. Sie müssen die DVD-ROM manuell laden und dann die Befehle ausführen. 4. Navigieren Sie zum Verzeichnis SYSMGMT/ManagementStation/linux/rac.
ANMERKUNG: Um Sicherheitsrisiken zu beheben, überwacht Microsoft Internet Explorer streng die Zeit bei seiner Cookieverwaltung. Um dies zu unterstützen, muss die Computerzeit, die auf dem Internet Explorer ausgeführt wird, mit der Zeit auf dem CMC synchronisiert werden. Proxy-Server Um einen Proxy-Server zu durchsuchen, der keinen Zugriff auf das Verwaltungsnetzwerk hat, können Sie die Verwaltungsnetzwerkadresse zur Ausnahmenliste des Browsers hinzufügen.
Webserver ein Zertifikat verwendet, das sich auf einer Liste widerrufener Zertifikate befindet, die aus dem Internet abgerufen wurde. Wenn kein Zugriff auf das Internet möglich ist, kann diese Funktion zu Verzögerungen von mehreren Sekunden führen, wenn Sie mit dem Browser oder einer Befehlszeilenschnittstelle, wie z. B. Remote-RACADM, auf den CMC zugreifen. So deaktivieren Sie das Abrufen der Zertifikatsperrliste: 1. Starten Sie den Internet Explorer. 2.
Damit kann das Verwaltungsnetzwerk vom Serverdatennetzwerk getrennt werden. Es ist wichtig, diesen Datenverkehr zu trennen, um ununterbrochenen Zugriff auf die Gehäuseverwaltung zu haben. Der CMC ist mit dem Verwaltungsnetzwerk verbunden. Alle externen Zugriffe auf den CMC und die iDRACs werden über den CMC erreicht. Umgekehrt erfolgt der Zugriff auf die verwalteten Server über Netzwerkverbindungen zum E/A-Modul (EAM).
1. 2. So starten Sie die CMC-Konfiguration: • Bei einem Gehäuse, das zuvor nicht konfiguriert wurde, wird die LCD-Anzeige angezeigt. Navigieren Sie im Bereich LCD-Sprache über die Pfeilschaltflächen zur gewünschten Sprache. Wenn die gewünschte Sprache angezeigt wird, wählen Sie die Sprache aus, indem Sie auf die Schaltfläche in der Mitte drücken. Daraufhin werden die Netzwerkeinstellungen angezeigt. • Bei einem Gehäuse, das zuvor konfiguriert wurde, wird der Bildschirm Hauptmenü angezeigt.
• Wählen Sie Autom. (1 GB) aus, indem Sie auf die Schaltfläche in der Mitte drücken. Drücken Sie anschließend erneut auf die Schaltfläche in der Mitte. Daraufhin wird der Bereich Protokoll angezeigt. Fahren Sie dann mit Schritt 6 fort. • Wählen Sie 10 MB oder 100 MB aus. Daraufhin wird der Bereich Duplex angezeigt. Fahren Sie dann mit Schritt 5 fort. Drücken Sie ansonsten 5.
Sie können iDRAC auch über die CMC-Web-Schnittstelle konfigurieren. 12. Wählen Sie im Feld Protokoll die IP-Adresse aus, die Sie für die Server verwenden möchten: • IPv4 – Die Optionen von DHCP oder Statisch werden angezeigt. • Beide • IPv6 – Die Optionen DHCP oder Statisch werden angezeigt. – Der Bereich iDRAC-Konfiguration wird angezeigt; fahren Sie dann mit Schritt 15 fort. 13. Wählen Sie DHCP oder Statisch aus.
Um alle iDRAC-Netzwerkeinstellungen auf die installierten Server anzuwenden, markieren Sie das Kontrollkästchen-Symbol, und drücken Sie dann die Schaltfläche in der Mitte. Wählen Sie andernfalls das „X“ -Symbol aus, und drücken auf die Schaltfläche in der Mitte. 16. Die folgende Meldung wird im nächsten Fensterbereich iDRAC-Konfiguration angezeigt.
Schnittstelle Beschreibung Eine Liste der unterstützten Webbrowser finden Sie im Abschnitt „Supported Browsers“ (Unterstützte Webbrowser) in der Dell Systems Software Support Matrix unter dell.com/support/manuals. Remote-RACADMBefehlszeilenschnittstelle Verwenden Sie dieses Befehlszeilen-Dienstprogramm, um CMC und dessen Komponenten zu verwalten.
Schnittstelle Beschreibung Verwaltungsinformationen (Distributed Management Task Force; Common Information Model). Die CIM-Informationen definieren die Semantik- und Informationstypen, die in einem verwalteten System geändert werden können. Die CMC WS-MAN-Implementierung verwendet SSL auf Schnittstelle 443 für Transportsicherheit und unterstützt Standardauthentifizierung.
Einrichten des physischen Standorts und des Namens für das Gehäuse über die Webschnittstelle So richten Sie den Standort und den Namen für ein Gehäuse über die Webschnittstelle ein: 1. Wählen Sie im rechten Fensterbereich Gehäuseübersicht aus und klicken Sie auf Setup. 2. Geben Sie auf der Seite Allgemeine Gehäuseeinstellungen den physischen Standort und den Gehäusenamen ein. Weitere Informationen zum Festlegen der Gehäuseeigenschaften finden Sie in der Online Hilfe.
LEDs zum Identifizieren von Komponenten im Gehäuse konfigurieren Sie können die LEDs von Komponenten (Gehäuse, Server, physische Festplattenlaufwerke, virtuelle Festplatten, und E/A Module) zum Blinken aktivieren, damit Sie die Komponenten auf dem Gehäuse identifizieren können. ANMERKUNG: Zum Modifizieren dieser Einstellungen müssen Sie die Berechtigung als Gehäusekonfigurations-Administrator besitzen.
racadm raid , wobei der Wert Vorgang blink oder unblink ist und der FQDD für das physische Festplattenlaufwerk und die virtuelle Festplatte der Komponente ist. CMC-Eigenschaften konfigurieren Sie können CMC-Eigenschaften, wie z. B. Strombudget, Netzwerkeinstellungen, Benutzer sowie SNMPund E-Mail-Warnungen über die Webschnittstelle oder RACACM-Befehle konfigurieren.
3. Um die Funktion Benutzer blockieren bzw. IP blockieren im Abschnitt Richtlinie für Anmeldesperrung zu aktivieren, wählen Sie Sperrung durch Benutzernamen bzw. Sperrung durch IP-Adresse (IPv4). Die Optionen zum Einstellen der anderen Attribute zur Anmeldesperrung sind aktiviert. 4. Geben Sie die erforderlichen Werte für die Richtlinienattribute der Anmeldesperrung in die aktivierten Felder – Sperrung Fehlerzähler, Sperrungsausfallfenster und Sperrung durch Zeitüberschreitung – ein.
• • • • • • Führen Sie den RACADM-Befehl racreset aus. Lesen Sie den Abschnitt racreset-Befehl im Chassis Management Controller for PowerEdge VRTX RACADM Command Line Reference Guide (RACADMBefehlszeilen-Referenzhandbuch für Chassis Management Controller für PowerEdge VRTX), verfügbar unter dell.com/support/manuals. Der aktive CMC wird über die Webschnittstelle zurückgesetzt.
• CMC-Firmware-Aktualisierung – Die Gehäuseverwaltung wird wieder aufgenommen, nachdem der CMC neu gestartet oder das Gehäuse auf den Standby-CMC umgeschaltet wurde. Es wird empfohlen, zunächst den Standby-CMC zu aktualisieren, so dass nur ein Failover-Ereignis auftreten kann. • CMC-Fehlererkennung und -behebung – Die Gehäuseverwaltung wird wieder aufgenommen, nachdem der CMC zurückgesetzt oder das Gehäuse auf den Standby-CMC umgeschaltet wurde.
Konfigurieren von LCD 1. Klicken Sie im linken Fensterbereich auf Gehäuseübersicht → Frontblende → Setup . 2. Auf der Seite Eigenschaften, im Abschnitt LCD-Konfiguration: • Wählen Sie die Option LCD-Bedienfeld sperren aus, um sämtliche Konfigurationen, die Sie unter Verwendung der LCD-Schnittstelle ausführen können, zu deaktivieren. • Wählen Sie aus dem Dropdown-Menü LCD-Sprache die erforderliche Sprache aus.
Einen Server einem DVD-Laufwerk zuordnen So ordnen Sie den Server dem Gehäuse -DVD-Laufwerk zu: 1. Klicken Sie im linken Fensterbereich auf Gehäuseübersicht → Frontblende → Setup . 2. Auf der Seite Frontblendenkonfiguration im Abschnitt DVD-Laufwerkskonfiguration: Wählen Sie im Drop-Down-Menü DVD zugeordnet einen der Server aus. Wählen Sie die Server aus, für die Zugriff zum Gehäuse -DVD-Laufwerk erforderlich ist. 3. Klicken Sie auf Anwenden.
Anmeldung beim CMC 3 Sie können sich beim CMC als CMC-Lokalbenutzer, als Microsoft Active Directory-Benutzer oder als LDAP-Benutzer anmelden. Der Standardbenutzername lautet root, und das Standardkennwort lautet calvin. Sie können sich auch über die einmalige Anmeldung (SSO) oder eine Smart Card anmelden.
ANMERKUNG: Um die Sicherheit zu erhöhen, empfiehlt Dell dringend, das Standardkennwort des Root-Kontos bei der Ersteinrichtung zu ändern. Das CMC-Modul unterstützt keine erweiterten ASCII-Zeichen, wie ß, å, é, ü oder andere in nichtenglischen Sprachen verwendete Sonderzeichen. So melden Sie sich als lokaler Benutzer, Active Directory-Benutzer oder LDAP-Benutzer an. 1. Geben Sie im Feld Benutzername Ihren Benutzernamen ein: • CMC-Benutzername: • Active Directory-Benutzername: \
So melden Sie sich über eine Smart Card als Active Directory-Benutzer bei CMC an: 1. Melden Sie sich beim CMC unter Verwendung von https:// an. Die CMC-Anmeldeseite wird eingeblendet und fordert Sie zum Einlegen einer Smart Card auf. ANMERKUNG: Falls Sie die Standard-HTTPS-Schnittstellennummer (80) geändert haben, greifen Sie mit
So melden Sie sich am CMC unter Verwendung von SSO an: 1. Melden Sie sich unter Verwendung Ihres Netzwerkkontos beim Clientsystem an. 2. Greifen Sie auf die CMC-Webschnittstelle über https:// zu. Beispiel: cmc-6G2WXF1.cmcad.lab, wobei cmc-6G2WXF1 der CMC-Name ist und cmcad.lab der Domänenname. ANMERKUNG: Falls Sie die Standard-HTTPS-Schnittstellennummer (80) geändert haben, greifen Sie mit
• Firmware-RACADM - damit können Sie sich über Telnet, SSH oder eine serielle Verbindung am CMC anmelden. Mit Firmware-RACADM wird die RACADM-Implementierung ausgeführt, die Teil der CMCFirmware ist. Sie können RACADM-Befehle in Skripts im Remote-Zugriff zum Konfigurieren mehrerer CMCs verwenden. Sie können keine Skripts direkt auf der CMC-Web-Schnittstelle ausführen, da CMC kein Scripting unterstützt.
Schnittstelle Anzahl der Sitzungen Telnet 4 SSH 4 Ändern des standardmäßigen Anmeldungskennworts Die Warnmeldung, die Sie auffordert das standardmäßige Anmeldungskennwort zu ändern, wird angezeigt, wenn: • Sie sich beim CMC mit der Berechtigung Benutzer konfigurieren anmelden. • Die Warnungsfunktion des standardmäßigen Kennworts aktiviert ist. • Wenn der standardmäßige Benutzername und das Kennwort des derzeit aktivierten Kontos root bzw. calvin sind.
Ändern eines in den Standardeinstellungen festgelegten Anmeldungskennworts unter Verwendung von RACADM So ändern Sie ein Kennwort mithilfe der Ausführung des folgenden RACADM-Befehls: racadm config –g cfgUserAdmin –o cfgUserAdminPassword –i wobei ein Wert zwischen 1 und 16 ist (und für das Benutzerkonto steht) und () das neue benutzerdefinierte Kennwort ist.
Aktualisieren der Firmware 4 Sie können die Firmware für Folgendes aktualisieren: • CMC – Aktiv und Standby • Gehäuseinfrastruktur • E/A-Modul • iDRAC7 Sie können die Firmware für folgende Serverkomponenten aktualisieren: • iDRAC • BIOS • Lifecycle-Controller • 32–Bit-Diagnose • Treiberpaket des Betriebssystems • Netzwerkschnittstellen-Controller • RAID-Controller Herunterladen der CMC-Firmware Bevor Sie mit der Firmwareaktualisierung beginnen, laden Sie die aktuelle Firmwareversion
Wenn sich im Gehäuse ein Server einer früheren Generation befindet, dessen iDRAC sich im Wiederherstellungsmodus befindet oder wenn der CMC beschädigte iDRAC-Firmware erkennt, wird der iDRAC einer früheren Generation ebenfalls auf der Seite Firmware-Aktualisierung aufgeführt.
vorhergehenden Rollen der CMCs wiederherzustellen. Die CMC Firmwareversion 2.x aktualisiert sowohl den primären CMC als auch den redundanten CMC ohne Ausführung des cmcchangeover-Befehls. Um zu vermeiden, dass die Verbindung von Benutzern während des Resets unterbrochen wird, benachrichtigen Sie bitte berechtigte Benutzer, die sich am CMC anmelden könnten, und prüfen Sie auf aktive Sitzungen, indem Sie die Seite Sitzungen anzeigen.
• Klicken Sie während der Dateiübertragung nicht auf das Symbol Aktualisierung und navigieren Sie nicht zu einer anderen Seite. • Um den Prozess abzubrechen, klicken Sie auf die Option Dateiübertragung und Aktualisierung abbrechen. Diese Option ist nur während der Dateiübertragung verfügbar. • Das Feld Aktualisierungsstatus zeigt den Firmware-Aktualisierungsstatus an. ANMERKUNG: Der Aktualisierungsvorgang kann für den CMC einige Minuten dauern.
Server-iDRAC-Firmware aktualisieren Sie können Firmware für iDRAC7 oder höher aktualisieren. Um diese Funktione zu nutzen, müssen Sie über eine Enterprise-Linzenz verfügen Die iDRAC-Firmware-Version muss 1.40.40 oder höher für Server mit iDRAC sein. Der iDRAC (auf einem Server) wird zurückgesetzt und ist vorübergehend nach einer FirmwareAktualisierung nicht verfügbar.
4. Klicken Sie auf Firmware-Aktualisierung beginnen und dann klicken Sie auf Ja. Der Abschnitt Fortschritt der Firmware-Aktualisierung bietet Statusinformationen zur Firmwareaktualisierung. Eine Fortschrittsleiste zeigt den Status des Hochladevorgangs an. Die Übertragungszeit kann je nach Verbindungsgeschwindigkeit variieren. Wenn der interne Aktualisierungsprozess beginnt, wird die Seite laufend aktualisiert und zeigt den Firmwareaktualisierungszeitgeber an.
Servern können Sie die Lifecycle-Controller-Firmware installieren und die iDRAC-Firmware aktualisieren, um den Lifecycle-Controller-Dienst zu aktivieren. Für ältere Servergenerationen ist diese Aktualisierung möglicherweise nicht möglich. Normalerweise wird die Lifecycle-Controller-Firmware über ein geeignetes Installationspaket installiert, das auf dem Server-Betriebssystem ausgeführt werden muss. Für unterstützte Server ist ein spezielles Reparatur-/Installationspaket mit einer Dateinamenerweiterung .
Filtern von Komponenten für Firmware-Aktualisierungen Informationen über alle Komponenten und Geräte werden über alle Server hinweg auf einmal abgerufen. Um diese große Menge an Informationen zu verwalten, stellt der Lifecycle-Controller verschiedene Filtermechanismen zur Verfügung. ANMERKUNG: Um diese Funktion zu nutzen, benötigen Sie eine Enterprise-Lizenz. Diese Filter ermöglichen Ihnen Folgendes: • Eine oder mehr Kategorien von Komponenten oder Geräten für das bequeme Anzeigen auswählen.
Filtern von Komponenten für Firmware-Aktualisierungen mit der CMC-Webschnittstelle So filtern Sie die Geräte 1. Gehen Sie im linken Fensterbereich zu Server-Übersicht und klicken Sie dann auf Aktualisierung. 2.
ANMERKUNG: Um diese Funktion verwenden zu können, benötigen Sie eine Enterprise-Lizenz.
Firmwarebestandsaufnahme über die CMC-Webschnittstelle anzeigen So zeigen Sie die Firmware-Bestandsaufnahme an: 1. Klicken Sie im linken Fensterbereich auf Server-Übersicht und klicken Sie dann auf Aktualisierung. 2. Zeigen Sie auf der Seite Serverkomponenten-Aktualisierung die Firmware-Bestandsaufnahmedetails im Abschnitt Komponente/Gerät-Firmware-Bestandsaufnahme an.
Feld Beschreibung weniger als vier Steckplätze mit Servern belegt sind, werden nur die mit Servern bestückten Steckplätze angezeigt. Name Zeigt den Namen des Servers in den einzelnen Steckplätzen an. Modell Zeigt das Modell des Servers an. Komponente/ Gerät Zeigt eine Beschreibung der Komponente oder des Geräts auf dem Server an. Wenn die Spaltenbreite zu schmal ist, stellt das Mouse-Over-Hilfswerkzeug eine Ansicht mit der Beschreibung bereit.
Es kann immer nur ein Vorgangstyp durchgeführt werden. Nicht unterstützte Komponenten und Server werden möglicherweise als Teil der Bestandsliste aufgeführt, Lifecycle Controller-Vorgänge sind jedoch zulässig. Zum Durchführen der verschiedenen Lifecycle Controller-Vorgänge brauchen Sie: • Für CMC: Server Administrator-Berechtigung. • Für iDRAC: iDRAC-Konfigurationsberechtigung und iDRAC-Anmeldungsberechtigung.
Zurücksetzen der Serverkomponenten-Firmware Sie können das Firmware-Image der zuvor installierten Frimware für ausgewählte Komponenten oder Geräte über einen oder mehrere Server hinweg installieren. Das Firmware-Image steht innerhalb des Lifecycle Controllers für einen Rollback-Vorgang zur Verfügung. Die Verfügbarkeit unterliegt der Versionskompatibilitätslogik des Lifecycle Controllers. Es wird auch angenommen, dass die vorherige Aktualisierung mittels des Lifecycle Controllers stattgefunden hat.
Aktualisierungen versucht, überschreitet die kombinierte Größe aller Firmware-Aktualisierungen möglicherweise 48 MB. In einem solchen Fall schlägt eine der Komponenten-Aktualisierungen fehl, da deren Aktualisierungsdatei abgeschnitten wird. Zum Aktualisieren mehrerer Komponenten auf einem Server wird empfohlen, zuerst die Lifecycle-Controller- und 32-Bit-Diagnose-Komponenten zusammen zu aktualisieren. Diese benötigen keinen Neustart des Servers und können relativ schnell abgeschlossen werden.
6. Klicken Sie auf Aktualisieren. Die Firmware-Version für die ausgewählten Komponenten oder Geräte wird aktualisiert. Geplante Serverkomponenten-Firmware-Jobs löschen ANMERKUNG: Um diese Funktion verwenden zu können, benötigen Sie eine Enterprise-Lizenz. Sie können Jobs löschen, die für die ausgewählten Komponenten und/oder Geräte über einen oder mehrere Server hinweg geplant sind.
6. Klicken Sie auf Aktualisieren. Die Firmware-Aktualisierung wird für die ausgewählten Komponenten gestartet. Der Fortschritt wird in der Spalte Aktualisieren angezeigt. Nachdem der Vorgang abgeschlossen ist, wird eine entsprechende Meldung angezeigt wird, die den Abschluss oder das Scheitern der Firmware-Aktualisierung anzeigt. iDRAC-Firmware mittels CMC wiederherstellen iDRAC-Firmware wird normalerweise mit dem iDRAC, z. B.
5 Gehäuseinformationen anzeigen und Funktionszustandsüberwachung von Gehäuse und individuellen Komponenten Sie können Informationen anzeigen und den Funktionszustand für Folgendes überwachen: • • • • • • • • • • Aktive und Standby-CMC Alle Server und einzelne Server E/A-Modul Lüfter Netzteile Temperatursensoren Festplattenlaufwerke LCD-Baugruppe Speicher-Controller PCIe-Geräte Gehäuse- und Komponenten-Zusammenfassungen anzeigen Wenn Sie sich an der CMC-Webschnittstelle anmelden, zeigt die Seite Gehäusefu
(EAMs), Lüfter, Netzteileinheiten (PSUs), LCD-Einheit, Speicher-Controller und PCIe-Geräte an. Detaillierte Informationen über die einzelnen Komponenten erhalten Sie, wenn Sie auf die jeweilige Komponente klicken. Außerdem werden die neuesten Ereignisse im CMC-Hardwareprotokoll angezeigt. Weitere Informationen finden Sie in der Online Hilfe. Wenn Ihr Gehäuse als Gruppenführung konfiguriert wurde, wird nach der Anmeldung die Seite Gruppenfunktionszustand angezeigt.
Symbol Beschreibung Es ist kein Server vorhanden. Ausgewählte Komponenteninformationen Die Informationen für die ausgewählte Komponente werden in drei getrennten Bereichen angezeigt: • Funktionszustand, Leistung und Eigenschaften – Zeigt die aktiven, kritischen und nicht-kritischen Ereignisse gemäß der Anzeige im Hardwareprotokoll und die mit der Zeit variierenden Leistungsdaten an. • Eigenschaften – Zeigt die Komponenteneigenschaften an, die sich nicht mit der Zeit ändern oder sich nur selten ändern.
Gehäusezusammenfassung anzeigen Um die Gehäusezusammenfassungsinformationen im linken Fensterbereich anzuzeigen, klicken Sie auf Gehäuseübersicht → Eigenschaften → Zusammenfassung. Die Seite Gehäusezusammenfassung wird angezeigt. Weitere Informationen zu dieser Seite finden Sie in der Online-Hilfe. Gehäuse-Controllerinformationen und Status anzeigen Um Gehäuse-Controllerinformationen und Status anzuzeigen, klicken Sie in der CMC-WebSchnittstelle auf Gehäuseübersicht → Gehäuse-Controller.
Anzeigen des Funktionszustands eines einzelnen Servers So zeigen Sie den Funktionszustand von einzelnen Servern an: 1. Klicken Sie auf Gehäuse-Übersicht → Eigenschaften → Funktionszustand. Die Seite Gehäusefunktionszustand bietet einen grafischen Überblick über alle Server, die im Gehäuse installiert sind. Der Serverfunktionszustand wird durch die Farbe der Server-Untergrafik angegeben. Positionieren Sie den Cursor auf einer einzelnen Server-Untergrafik.
Anzeigen der Informationen und des Funktionszustands für einzelne E/A-Module Um den Funktionszustand des einzelnen E/A-Module in der CMC-Webschnittstelle anzuzeigen, führen Sie einen der folgenden Schritte aus: 1. Gehen Sie zu Gehäuseübersicht → Eigenschaften → Funktionszustand. Die Seite Gehäusefunktionszustand wird angezeigt. Der untere Abschnitt der Gehäuse-Grafiken stellt die Rückansicht des Gehäuses dar und enthält den Funktionszustand der E/A-Module.
So zeigen Sie den Funktionszustand der Lüfter über die CMC-Webschnittstelle an: 1. Gehen Sie zu Chassis Overview. Die Seite Gehäusefunktionszustand wird angezeigt. Der untere Abschnitt der Gehäuse-Grafiken zeigt die linke Ansicht des Gehäuses und enthält den Funktionszustand der Lüfter. Der LüfterFunktionszustand wird durch die Farbe der Lüfter-Untergrafik angegeben. Positionieren Sie den Cursor auf die Lüfter-Untergrafik. Der Texthinweis liefert zusätzliche Informationen zum Lüfter.
Um diese Funktionen unter Verwendung von RACADM-Befehlen einzurichten, verwenden Sie den folgenden Befehl: racadm fanoffset [-s ] Weitere Informationen über die RACADM-Befehle, die mit „Lüfter-Offset“ in Verbindung stehen finden Sie im Chassis Management Controller for PowerEdge VRTX RACADM Command Line Reference Guide (RACADM-Befehlszeilen-Referenzhandbuch für Chassis Management Controller für PowerEdge VRTX), verfügbar unter dell.com/support/manuals.
KVM-Informationen und Funktionszustand anzeigen Um den Funktionszustand der mit dem Gehäuse verbundenen KVMs anzuzeigen, führen Sie eine der folgenden Optionen aus: 1. Klicken Sie auf Gehäuseübersicht. Die Seite Gehäusefunktionszustand wird angezeigt. Der linke Bereich zeigt die Vorderansicht des Gehäuses an und enthält den Funktionszustand eines KVM. Der KVM-Funktionszustand wird durch die Farbe der KVM-Untergrafik angegeben.
Informationen und Funktionszustand der Temperatursensoren anzeigen So zeigen Sie den Funktionszustand der Temperatursensoren an: Klicken Sie im linken Fensterbereich auf Gehäuseübersicht → Temperatursensoren. Die Seite Temperatursensorstatus zeigt den Status und die Messergebnisse der Temperatursonden des gesamten Gehäuses an (Gehäuse und Server). Weitere Informationen finden Sie in der OnlineHilfe. ANMERKUNG: Der Temperatursondenwert kann nicht bearbeitet werden.
Den CMC konfigurieren 6 Mit Chassis Management Controller können Sie Eigenschaften konfigurieren, Benutzer einrichten und Warnungen für die Ausführung von Remote-Verwaltungstasks einrichten. Bevor Sie mit der Konfiguration des CMC beginnen, müssen Sie zuerst die CMC-Netzwerkeinstellungen konfigurieren, sodass Sie den CMC im Fernzugriff verwalten können. Diese ursprüngliche Konfiguration weist die TCP/IP-Netzwerkbetriebsparameter zu, die den Zugriff auf den CMC aktivieren.
Wenn Sie zwei CMCs (Aktiv und Standby) im Gehäuse haben und sie mit dem Netzwerk verbunden sind, dann übernimmt der Standby-CMC automatisch die Netzwerkeinstellungen des aktiven CMC im Falle eines Failovers. Wenn IPv6 beim Start aktiviert ist, dann werden alle vier Sekunden drei Router-Anfragen ausgesendet.
Um die CMC-IPv4-Adressierung zu aktivieren oder zu deaktivieren, geben Sie Folgendes ein: racadm config -g cfgLanNetworking -o cfgNicIPv4Enable 1 racadm config -g cfgLanNetworking -o 4cfgNicIPv4Enable 0 ANMERKUNG: Die CMC-IPv4-Adressierung ist standardmäßig aktiviert.
Um die Funktion „DHCP für DNS-Adresse“ zu deaktivieren und die statischen und alternativen DNSServer-Adressen festzulegen, geben Sie Folgendes ein: racadm config -g cfgLanNetworking -o cfgDNSServersFromDHCP 0 Um die Funktion „DHCP für DNS-Adresse“ für IPv6 zu deaktivieren und bevorzugte statische und alternative DNS-Server-Adressen anzugeben, geben Sie Folgendes ein: racadm config -g cfgIPv6LanNetworking -o cfgIPv6DNSServersFromDHCP6 0 Statische DNS-Server-IP-Adressen einrichten ANMERKUNG: Die Einstellunge
Sie können die automatische Verhandlung deaktivieren und den Duplexmodus sowie die Netzwerkgeschwindigkeit festlegen, indem Sie Folgendes eingeben: racadm config -g cfgNetTuning -o cfgNetTuningNicAutoneg 0 racadm config -g cfgNetTuning -o cfgNetTuningNicFullDuplex wobei: ist 0 (Halbduplex) oder 1 (Vollduplex, Standardeinstellung) racadm config -g cfgNetTuning -o cfgNetTuningNicSpeed wobei: ist 10 oder 100 (Standard) Einstellen der maximalen Übertragungs
So konfigurieren Sie IP-Bereichsattribute über die CMC-Webschnittstelle: 1. Wählen Sie im linken Fensterbereich Gehäuseübersicht aus und klicken Sie auf Netzwerk → Netzwerk. Die Seite Netzwerkkonfiguration wird angezeigt. 2. Klicken Sie im Abschnitt IPv4-Einstellungen auf Erweiterte Einstellungen. Die Seite Anmeldesicherheit wird angezeigt. Alternativ können Sie auf die Seite Anmeldesicherheit zugreifen, indem Sie im linken Fensterbereich Gehäuseübersicht wählen und aufSicherheit → Anmeldungklicken. 3.
Konfiguration der virtuellen LAN-Tag-Eigenschaften für CMC mittels RACADM 1. Aktivieren Sie die Funktionen für das virtuelle LAN (VLAN) des externen Gehäuseverwaltungsnetzwerks: racadm config -g cfgLanNetworking -o cfgNicVLanEnable 1 2. Geben Sie die VLAN-Kennung für das externe Gehäuseverwaltungsnetzwerk an: racadm config -g cfgLanNetworking -o cfgNicVlanID Gültige Werte für sind 1– 4000 und 4021– 4094. Der Standardwert ist 1.
Dienste konfigurieren Sie können die folgenden Dienste auf CMC konfigurieren und aktivieren: • CMC Serielle Konsole – Aktivieren Sie den Zugriff auf CMC unter Verwendung der seriellen Konsole. • Web Server – Aktivieren Sie den Zugriff auf CMC Web-Schnittstelle. Die Deaktivierung des Web Servers deaktiviert auch den Remote-RACADM. • SSH – Aktivieren Sie den Zugriff auf CMC über Firmware RACADM.
Dienste unter Verwendung der CMC-Webschnittstelle konfigurieren So konfigurieren Sie CMC-Dienste über die CMC-Webschnittstellle: 1. Klicken Sie im linken Fensterbereich auf Gehäuse-Übersicht, und klicken Sie dann auf Netzwerk → Dienste. Die Seite Diensteverwaltung wird angezeigt. 2. Konfigurieren Sie die folgenden Dienste nach Bedarf: • CMC seriell • Webserver • SSH • Telnet • Remote-RACADM • SNMP • Remote-Syslog Weitere Informationen zu den Feldern finden Sie in der Online-Hilfe. 3.
Erweiterte CMC-Speicherkarte konfigurieren Sie können die optionalen wechselbaren Flash-Datenträger für die Verwendung als erweiterten nichtflüchtigen Speicher aktivieren oder reparieren. Der Betrieb einiger CMC-Funktionen ist von erweitertem nicht-flüchtigem Speicher abhängig. So aktivieren oder reparieren Sie den wechselbaren Flash-Datenträger mithilfe der CMCWebschnittstelle: 1. Gehen Sie im linken Fensterbereich auf Gehäuseübersicht und klicken Sie dann auf GehäuseController → Flash-Datenträger. 2.
3. Wählen Sie auf der Gehäusegruppenseite unter Rolle Führung. Es wird ein Feld zum Hinzufügen des Gruppennamens angezeigt. 4. Geben Sie den Gruppennamen im Feld Gruppenname ein und klicken Sie anschließend auf Anwenden. ANMERKUNG: Für einen Domänennamen gelten die gleichen Regeln wie für den Gruppennamen. Die Gehäusegruppe wechselt beim Erstellen der Gehäusegruppe automatisch zur GehäusegruppenSeite.
4. Wählen Sie aus der Liste Mitglieder entfernen den zu löschenden Mitgliedernamen aus, und klicken Sie anschließend auf Anwenden. Das Führungsgehäuse benachrichtigt anschließend das Mitglied, bzw. die Mitglieder, sollten mehr als eines ausgewählt worden sein, dass es bzw. sie aus der Gruppe entfernt wurde(n). Der Mitgliedsname wird aus dem Dialogfeld entfernt.
3. Wenn ein Mitglieds-CMC das benötigte Ziel ist, dann wählen Sie für das gewünschte Gehäuse CMC starten aus. Wenn ein Server in einem Gehäuse das benötigte Ziel ist, verfahren Sie folgendermaßen: a. Wählen Sie das Bild des Zielgehäuses aus. b. Wählen Sie im Gehäuseabbild, das im Abschnitt Funktionszustand erscheint, den Server. c. Wählen Sie im mit Quicklinks bezeichneten Kästchen das Zielgerät aus. Es wird ein neues Fenster mit der Zielseite oder dem Anmeldebildschirm angezeigt.
Speichern des Berichts zur Serverbestandsaufnahme So speichern Sie den Bericht zur Serverbestandsaufnahme über die CMC-Webschnittstelle: 1. Wählen Sie im linken Fensterbereich die Gruppe aus. 2. Klicken Sie auf der Seite Funktionszustand der Gehäusegruppe auf Bericht zur Bestandsliste speichern. Das Dialogfeld Datei-Download wird angezeigt und Sie werden dazu aufgefordert, die Datei zu öffnen oder zu speichern. 3.
Datenfeld Beispiel ANMERKUNG: Es wird ein ServerAdministrator-Agent benötigt, der auf dem Server ausgeführt wird. Ansonsten wird er leer angezeigt. Betriebssystem Windows Server 2008 ANMERKUNG: Es wird ein ServerAdministrator-Agent benötigt, der auf dem Server ausgeführt wird. Ansonsten wird er leer angezeigt. Modell PowerEdgeM610 Service Tag 1PB8VF1 Gesamtsystemspeicher 4 GB ANMERKUNG: Erfordert VRTX CMC 1.0 (oder neuer) auf dem Mitglied. Ansonsten wird es leer angezeigt.
• CPLD • USC • Diagnose • BS-Treiber • RAID • NIC ANMERKUNG: Die Bestandsinformationen zu Gehäusegruppe, Mitgliedsgehäuse, Servern und Serverkomponenten werden jedes Mal aktualisiert, wenn ein Gehäuse zur Gruppe hinzugefügt oder daraus entfernt wird. Anzeigen der Bestandslisten von Gehäusegruppen Um mithilfe der CMC-Webschnittstelle eine Gehäusegruppe anzeigen zu lassen, wählen Sie im linken Fensterbereich Gruppe aus. Klicken Sie auf Eigenschaften → Firmware-Version.
Wenn Sie eine spezifische CMC-Karte mit deren Gruppen-ID und Objekt-ID abfragen, erstellt RACADM die racadm.cfg-Konfigurationsdatei aus den abgerufenen Informationen. Wenn Sie die Datei zu einem oder mehreren CMCs exportieren, können Sie in kürzester Zeit Ihre Controller mit identischen Eigenschaften konfigurieren. ANMERKUNG: Einige Konfigurationsdateien enthalten eindeutige CMC-Informationen (wie die statische IP-Adresse), die vor dem Exportieren der Datei zu anderen CMCs geändert werden müssen. 1.
RACADM parst die Datei .cfg, wenn Sie zum ersten Mal auf den CMC geladen wird, um zu überprüfen, dass gültige Gruppen- und Objektnamen vorhanden sind und einfache Syntaxregeln eingehalten werden. Fehler werden mit der Zeilennummer markiert, in der der Fehler ermittelt wurde. Eine Meldung beschreibt das Problem. Die gesamte Datei wird auf Richtigkeit geparst und alle Fehler werden angezeigt. Wenn ein Fehler in der .cfg-Datei festgestellt wird, werden Schreibbefehle nicht zum CMC übertragen.
Eine Kommentarzeile muss in Spalte 1 beginnen. Ein „#“-Zeichen in jeder anderen Spalte wird als das Zeichen # behandelt. Einige Modemparameter können #-Zeichen in den Zeichenketten enthalten. Ein Escape-Zeichen ist nicht erforderlich. Sie können einen .cfg-Befehl von einem racadm getconfig -f .cfg-Befehl erstellen und dann einen racadm config -f .cfg-Befehl auf einem anderen CMC ausführen, ohne dass Sie Escape-Zeichen hinzufügen müssen.
• Für indizierte Gruppen muss es sich bei dem Objektanker um das erste Objekt nach dem "[ ]"-Paar handeln. Im Folgenden finden Sie Beispiele für aktuelle indizierte Gruppen: [cfgUserAdmin] cfgUserAdminUserName= • Wenn bei Verwendung von Remote-RACADM zur Erfassung der Konfigurationsgruppen in eine Datei eine Schlüsseleigenschaft innerhalb einer Gruppe nicht festgelegt ist, wird die Konfigurationsgruppe nicht als Teil der Konfigurationsdatei gespeichert.
Anzeigen und Beenden der CMC-Sitzungen über die Webschnittstelle So verwalten oder beenden Sie eine Sitzung über die Webschnittstelle: 1. Wählen Sie in der Systemstruktur Gehäuseübersicht aus und klicken Sie auf Netzwerk → Sitzungen. Daraufhin werden auf der Seite Sitzungen die Sitzungs-ID, der Benutzername, die IP-Adresse und der Sitzungstyp angezeigt. Weitere Informationen zu diesen Eigenschaften finden Sie in der OnlineHilfe. 2. Um die Sitzung zu beenden, klicken Sie für die Sitzung auf Beenden.
Server konfigurieren 7 Sie können die folgenden Einstellungen eines Servers konfigurieren: • Steckplatznamen • iDRAC-Netzwerkeinstellungen • DRAC-VLAN-Tag-Einstellungen • Erstes Startgerät • Server-FlexAddress • Remote-Dateifreigabe • BIOS-Einstellungen unter Verwendung der Funktion zum Klonen von Servern Steckplatznamen konfigurieren Steckplatznamen werden zur Identifizierung einzelner Server verwendet.
Die Einstellung des Steckplatznamens in der CMC-Webschnittstelle setzt immer die Änderungen außer Kraft, die auf der iDRAC-Schnittstelle am Anzeigenamen vorgenommen wurden. So bearbeiten Sie einen Steckplatznamen über die CMC-Webschnittstelle: 1. Klicken Sie im linken Fensterbereich auf Gehäuseübersicht → Serverübersicht → Setup → Steckplatznamen. 2. Bearbeiten Sie auf der Seite Steckplatznamen im Feld Steckplatznamen den Steckplatzname. 3.
So aktivieren Sie die iDRAC-Einstellungen für die schnelle Bereitschaft und stellen sie ein: 1. Klicken Sie im linken Fensterbereich auf Gehäuseübersicht → Setup → iDRAC. 2. Legen sie auf der Seite iDRAC bereitstellen, im Abschnitt QuickDeploy-Einstellungen, die Einstellungen fest, die in der folgenden Tabelle erwähnt wurden. Weitere Informationen über die Felder finden Sie in der Online-Hilfe. Tabelle 7.
Einstellung Beschreibung Option aktiviert ist, sind die Felder QuickDeployIP, QuickDeploy-Subnetzmaske und QuickDeploy-Gateway deaktiviert und können nicht geändert werden, da DHCP verwendet wird, um diese Einstellungen automatisch für jeden iDRAC zuzuweisen. Um diese Option auszuwählen, müssen Sie die option iDRAC IPv4 aktivieren auswählen. iDRAC-IPv4-Adresse starten (Steckplatz 1) Gibt die statische IP-Adresse des iDRAC des Servers in Steckplatz 1 des Gehäuses an.
3. Einstellung Beschreibung iDRAC IPv6-Präfixlänge Gibt die Präfixlänge an, die den IPv6-Adressen auf dem iDRAC zugewiesen wird. Der Standardwert ist 64. Klicken Sie auf QuickDeploy-Einstellungen speichern, um die Auswahl zu speichern. Wenn Sie die Änderungen an den Einstellungen des iDRAC-Netzwerkes vorgenommen haben, klicken Sie auf iDRAC-Netzwerkeinstellungen anwenden, um die Einstellungen zur iDRAC bereitzustellen.
3. Um die Einstellung auf dem iDRAC bereitzustellen, klicken Sie auf iDRAC-Netzwerkeinstellungen anwenden. Alle Änderungen an den Einstellungen zur schnellen Bereitstellung werden ebenfalls gespeichert. Die Tabelle iDRAC-Netzwerkeinstellungen zeigt zukünftige Netzwerkkonfigurationseinstellungen; die für installierte Server angezeigten Werte können die gleichen sein wie die Werte der zurzeit installierten iDRAC-Netzwerkkonfigurationseinstellungen (müssen es aber nicht).
Beispiel: racadm setniccfg -m server-1 -v 1 7 Beispiel: • Um ein Server-VLAN zu entfernen, deaktivieren Sie die VLAN-Funktionen des angegebenen Servernetzwerks: racadm setniccfg -m server- -v Gültige Werte für sind 1–4. Beispiel: racadm setniccfg -m server- 1 -v Konfigurieren der iDRAC-VLAN-Tag-Einstellungen mittels der Webschnittstelle So konfigurieren Sie die VLAN für den Server: 1.
Tabelle 8. Startlaufwerke Startlaufwerk Beschreibung PXE Start von einem PXE (Preboot Execution Environment)-Protokoll über die Netzwerkschnittstellenkarte. Festplattenla ufwerk Start von der Festplatte auf dem Server. Lokale CD/DVD Start von einem CD- oder DVD-Laufwerk auf dem Server. Virtuelle Diskette Start vom virtuellen Diskettenlaufwerk.
So stellen Sie das erste Startlaufwerk für einzelne Server ein: 1. Wählen Sie im linken Fensterbereich Server-Übersicht aus und klicken Sie dann auf den Server, für den Sie das erste Startgerät einstellen wollen. 2. Wählen Sie Setup → Erstes Startgerät. Die Seite Erstes Startgerät wird angezeigt. 3. Wählen Sie im Dropdown-Menü Erstes Startgerät für jeden Server das zu verwendende Startgerät. 4.
3. Klicken Sie auf Verbinden, um eine Verbindung zu einer Remote-Dateifreigabe herzustellen. Um eine Verbindung zu einer Remote-Dateifreigabe herzustellen, müssen Sie den Pfad, den Benutzernamen und das Kennwort angeben. Ein erfolgreicher Vorgang ermöglicht den Zugriff auf den Datenträger. Klicken Sie auf Trennen, um eine zuvor verbundene Remote-Dateifreigabe zu trennen. Klicken Sie auf Bereitstellen, um das Datenträgergerät bereitzustellen.
• Anzeigen der Profil-Einstellungen eines Servers oder eines gespeicherten Profils. • Speichern eines Profils eines Servers. • Anwenden eines Profils auf andere Server. • Gespeicherte Profile von einer Remote-Dateifreigabe importieren. • Bearbeiten des Profilnamens und der Beschreibung. • Gespeicherte Profile auf eine Remote-Dateifreigabe exportieren. • Löschen von gespeicherten Profilen. • Ausgewählte Profile mittels der Funktion Quick Deploy für Zielgeräte bereitstellen.
ANMERKUNG: Wenn ein Server Lifecycle Controller nicht unterstützt oder das Gehäuse ausgeschaltet ist, können Sie kein Profil auf den Server anwenden. So wenden Sie ein Profil auf einen oder mehrere Server an: 1. Wählen Sie auf der Seite Serverprofile im Abschnitt Profile speichern und anwenden die Server aus, auf die Sie das ausgewählte Profil anwenden möchten. Das Drop-Down-Menü Profil auswählen wird aktiviert. 2.
Bearbeiten des Profils Sie können den Namen und die Beschreibung eines Serverprofils, das auf dem nicht flüchtigen CMCDatenträger (SD-Karte) gespeichert ist, bearbeiten. So bearbeiten Sie ein gespeichertes Profil: 1. Wählen Sie auf der Seite Serverprofile im Abschnitt Profile auf SD-Karte das benötigte Profil aus, und klicken Sie dann auf Profil bearbeiten. Der Abschnitt BIOS-Profil bearbeiten - wird angezeigt. 2.
3. Klicken Sie im linken Fensterbereich auf Gehäuseübersicht → Fehlerbehebung → LifecycleController-Aufträge. Suchen Sie die gleiche JID in der Tabelle Aufträge. Weitere Informationen über die Ausführung von Lifecycle-Controller-Aufträgen finden Sie in Lifecycle-ControllerAuftragsvorgänge. Quick Deploy von Profilen Mit der Quick Deploy-Funktion können Sie gespeicherte Profile einem Serversteckplatz zuweisen.
automatisch Administratorrechte. Dies gilt sogar dann, wenn derselbe Benutzer kein Konto auf iDRAC besitzt oder wenn das Konto keine Administratorrechte aufweist. • Ein CMC-Benutzer, der KEINE Serveradministratorrechte aufweist, aber dasselbe Konto auf iDRAC besitzt, wird automatisch mit einfacher Anmeldung bei iDRAC angemeldet. Sobald er sich auf der iDRAC-Site befindet, erhält dieser Benutzer die Berechtigungen, die für das iDRAC-Konto erstellt wurden.
Die Remote-Konsole kann auch von der iDRAC-Webschnittstelle gestartet werden. Weitere Informationen finden Sie im iDRAC User’s Guide (iDRAC-Benutzerhandbuch) unter dell.com/support/ manuals. Remote-Konsole von der Seite Gehäusefunktionszustand starten So starten Sie eine Remote-Konsole von der CMC-Webschnittstelle: 1. Klicken Sie im linken Fensterbereich auf Gehäuseübersicht und dann auf Eigenschaften. 2. Klicken Sie auf der Seite Gehäusefunktionszustand auf den angegebenen Server in der GehäuseGrafik.
CMC für das Versenden von Warnungen konfigurieren 8 Sie können Warnungen und Aktionen für bestimmte Ereignisse festlegen, die auf dem Gehäuse eintreten. Ein Ereignis wird erzeugt, wenn ein Gerät oder der Status eines Dienstes geändert wurde oder ein Fehlerzustand festgestellt wird.
Warnungen filtern Sie können Warnungen auf der Basis der Kategorie und des Schweregrads filtern. Warnungen über die CMC-Web-Schnittstelle filtern So filtern Sie Warnungen auf der Basis der Kategorie und des Schweregrads: ANMERKUNG: Um Konfigurationsänderungen der Gehäuseereignisse anzuwenden, müssen Sie die Berechtigung zur Warnungskonfiguration besitzen. 1. Klicken Sie im linken Fensterbereich auf Gehäuseübersicht → Warnungen. 2.
SNMP-Trap-Warnungsziele über die CMC-Webschnittstelle konfigurieren So konfigurieren Sie IPv4- oder IPv6-Warnzieleinstellungen über die CMC-Webschnittstelle: 1. Klicken Sie im linken Fensterbereich auf Gehäuseübersicht → Warnungen → Trap-Einstellungen. 2. Geben Sie auf der Seite Warnungsziele bei Gehäuseereignissen Folgendes ein: • Geben Sie im Feld Ziel eine gültige IP-Adresse ein. Verwenden Sie das 4-Punkt-IPv4-Format, die Standard-IPv6-Adressnotation oder FQDN. Beispiel: 123.123.123.
3. Geben Sie die Ereignisfilter durch Ausführung des Befehls racadm eventfilters set an. a. Um alle verfügbaren Einstellungen zu löschen, führen Sie den folgenden Befehl aus: racadm eventfilters set -c cmc.alert.all -n none b. Konfigurieren Sie die Verwendung des Schweregrads als Parameter. Wenn zum Beispiel allen informativen Ereignisse in der Speicherkategorie das Ausschalten als Maßnahme und E-Mail und SNMP als Benachrichtigungen zugewiesen sind: racadm eventfilters set -c cmc.alert.storage.
Einstellungen für E-Mail-Warnungen konfigurieren Wenn der CMC ein Gehäuseereignis ermittelt, wie z. B. eine Umgebungswarnung oder einen Komponentenfehler, kann er so konfiguriert werden, dass eine E-Mail-Warnung an eine oder mehrere EMail-Adressen gesendet wird. Sie müssen den SMTP-E-Mail-Server so konfigurieren, dass von der CMC-IP-Adresse weitergeleitete EMails angenommen werden können; eine Funktion, die bei den meisten Mail-Servern aus Sicherheitsgründen normalerweise deaktiviert ist.
4. So aktivieren Sie die Erstellung von E-Mail-Warnungen: racadm config -g cfgEmailAlert -o cfgEmailAlertEnable 1 -i wobei ein Wert von 1 - 4 ist. Die Indexnummer wird vom CMC verwendet, um bis zu vier konfigurierbare Ziel-E-Mail-Adressen zu unterscheiden. 5.
Benutzerkonten und Berechtigungen konfigurieren 9 Sie können Benutzerkonten mit spezifischen (rollenbasierten) Berechtigungen einrichten, um Ihr System über CMC zu verwalten und um die Systemsicherheit zu gewährleisten. Standardmäßig ist CMC mit einem lokalen Administratorkonto konfiguriert. Der Standardbenutzername lautet root, und das Kennwort lautet calvin. Als Administrator können Sie Benutzerkonten einrichten, damit andere Benutzer auf CMC zugreifen können.
Berechtigung Beschreibung Es ist möglich, dass ein Benutzer andere Berechtigungen ohne CMC-Anmeldebenutzerberechtigung besitzt. Diese Funktion ist sinnvoll, wenn sich ein Benutzer vorübergehend nicht anmelden darf. Wenn die CMC-Anmeldeberechtigung dieses Benutzers wiederhergestellt ist, erhält der Benutzer alle zuvor gewährten Berechtigungen zurück. GehäusekonfigurationAdministrator Benutzer können Daten hinzufügen oder ändern, die: • • • • das Gehäuse identifizieren, z. B.
Berechtigung Beschreibung Gehäusestromvorgänge steuern, einschließlich Strom einschalten, Strom ausschalten und Strom aus- und einschalten. ANMERKUNG: Für die Konfiguration von Stromversorgungseinstellungen ist eine Berechtigung als Administrator für die Gehäusekonfiguration erforderlich. Server Administrator Die Server-Administrator-Berechtigung ist eine Pauschalberechtigung, die einem CMC-Benutzer alle Rechte zum Ausführen beliebiger Vorgänge auf beliebigen, im Gehäuse vorhandenen Servern gewährt.
Berechtigung Beschreibung Benutzer konfigurieren: • iDRAC-Stammkennwort einstellen • iDRAC-Reset Serversteuerung-Administrator: • Einschalten • Ausschalten • Aus- und einschalten • Ordentliches Herunterfahren • Serverneustart Warnungstests für Benutzer Benutzer kann Testwarnungsmeldungen senden. Administrator für Debug-Befehle Benutzer kann Systemdiagnosebefehle ausführen. Struktur A-Administrator Benutzer kann die Struktur A-EAM festlegen und konfigurieren.
Benutzergruppe Gewährte Berechtigungen • • Warnungstests für Benutzer Struktur A-Administrator Gastbenutzer Anmelden Benutzerdefiniert Wählen Sie eine beliebige Kombination der folgenden Berechtigungen aus: • • • • • • • • • Keine CMC-Anmeldung, Benutzer Gehäusekonfiguration-Administrator Benutzerkonfigurations-Administrator Administrator zum Löschen von Protokollen Gehäusesteuerungs-Administrator (Strombefehle) Server Administrator Warnungstests für Benutzer Administrator für Debug-Befehle Struktur
Ändern der Einstellungen für StammbenutzerAdministratorkonto Zum Zweck der zusätzlichen Sicherheit wird dringend empfohlen, das Standardkennwort des Stammkontos (Benutzer 1) zu ändern. Das Stammkonto ist das Standard-Administrationskonto, das mit einem CMC geliefert wird. So ändern Sie das Standardkennwort für das Stammkonto: 1. Klicken Sie im linken Fensterbereich auf Gehäuseübersicht und dann auf Benutzerauthentifizierung. 2. Klicken Sie auf der Seite Benutzer, in der Spalte Benutzer-ID auf 1.
Sie können bis zu 16 Benutzer in der CMC-Eigenschaftsdatenbank konfigurieren. Bevor Sie einen CMCBenutzer manuell aktivieren, prüfen Sie, ob aktuelle Benutzer vorhanden sind. Wenn Sie einen neuen CMC konfigurieren oder den Befehl racadm racresetcfg verwendet haben, ist der einzige aktuelle Benutzer root mit dem Kennwort calvin. Der racresetcfg Unterbefehl setzt alle Konfigurationsparameter auf die Standardeinstellungen zurück. Alle vorherigen Änderungen gehen verloren.
ANMERKUNG: Eine Liste gültiger Bit-Maskenwerte für spezifische Benutzerberechtigungen ist im Chassis Management Controller for PowerEdge VRTX RACADM Command Line Reference Guide (RACADM-Befehlszeilen-Referenzhandbuch für Chassis Management Controller für PowerEdge VRTX) enthalten. Der Standard-Berechtigungswert ist 0, was darauf hinweist, dass der Benutzer über keine aktivierten Berechtigungen verfügt.
Konfigurieren von Active Directory-Benutzern Wenn Ihre Firma die Microsoft Active Directory-Software verwendet, kann die Software so konfiguriert werden, dass sie Zugriff auf CMC bietet. Sie können dann bestehenden Benutzern im Verzeichnisdienst CMC-Benutzerberechtigungen erteilen und diese steuern. Das ist eine lizenzierte Funktion. ANMERKUNG: Auf den folgenden Betriebssystemen können Sie die Benutzer der CMC-Benutzer unter Verwendung des Active Directory erkennen.
Rollengruppe StandardBerechtigungsebene Gewährte Berechtigungen • • • • • 2 Keine • • • • • • Bitmaske GehäusesteuerungsAdministrator (Strombefehle) Server Administrator Warnungstests für Benutzer Administrator für Debug-Befehle Struktur AAdministrator CMC-Anmeldung, 0x00000ed9 Benutzer Administrator zum Löschen von Protokollen GehäusesteuerungsAdministrator (Strombefehle) Server Administrator Warnungstests für Benutzer Struktur AAdministrator 3 Keine CMC-Anmeldung, Benutzer 0x00000001 4 Keine
Active Directory mit Standardschema unter Verwendung der CMC-Webschnittstelle konfigurieren ANMERKUNG: Weitere Informationen zu den verschiedenen Feldern finden Sie in der CMC-OnlineHilfe. 1. Wählen Sie in der Systemstruktur Gehäuse-Übersicht aus und klicken Sie auf BenutzerAuthentifizierung → Verzeichnisdienste. Die Seite Verzeichnisdienste wird angezeigt. 2. Wählen Sie Microsoft Active Directory (Standardschema) aus.
11. Melden Sie sich ab und dann beim CMC an, um die CMC Active Directory-Konfiguration abzuschließen. 12. Wählen Sie in der Systemstruktur Gehäuse aus, und navigieren Sie zur Registerkarte Netzwerk. Die Seite Netzwerkkonfiguration wird angezeigt. 13. Unter Netzwerkeinstellungen , wenn DHCP verwenden (für Netzwerkschnittstellen-IP-Adresse) ausgewählt ist, wählen Sie DHCP zum Abrufen der DNS-Serveradresse verwenden aus.
Konfiguration des Active Directory mit Standardschema unter Verwendung von RACADM Führen Sie an der RACADM-Befehszeileneingabe die folgenden Befehle aus: • Verwenden des Befehls config: racadm config -g cfgActiveDirectory -o cfgADEnable 1 racadm config -g cfgActiveDirectory -o cfgADType 2 racadm config -g cfgStandardSchema -i -o cfgSSADRoleGroupName racadm config -g cfgStandardSchema -i -o cfgSSADRoleGroupDomain racadm con
• Verwenden des Befehls config: racadm config -g cfgActiveDirectory -o cfgADCertValidationEnable 1 In diesem Fall müssen Sie mit dem folgenden RACADM-Befehl das CA-Zertifikat hochladen: racadm sslcertupload -t 0x2 -f ANMERKUNG: Wenn die Zertifikatüberprüfung aktiviert ist, geben Sie die Adressen des Domain Controller Server und die FQDN des globalen Katalogs an. Stellen Sie sicher, dass DNS ordnungsgemäß konfiguriert ist.
Geräteobjekten verbunden werden kann. Die Benutzer und RAC-Geräteobjekte können Mitglieder beliebiger Domänen im Unternehmen sein. Jedes Zuordnungsobjekt darf jedoch nur mit einem Berechtigungsobjekt verbunden werden (bzw. jedes Zuordnungsobjekt kann Benutzer, Benutzergruppen oder RAC-Geräteobjekte verbinden). Dieses Beispiel ermöglicht es dem Administrator, die Berechtigungen jedes Benutzers über spezielle CMCs zu steuern.
2. Erstellen Sie zwei Zuordnungsobjekte, A01 (mit universellem Bereich) und A02 in jeder Domäne. Die Abbildung „Active Directory-Objekte in mehreren Domänen einrichten“ zeigt die Objekte in Domäne2. 3. Erstellen Sie zwei RAC-Geräteobjekte, RAC1 und RAC2, die die zwei CMCs repräsentieren. 4. Erstellen Sie zwei Berechtigungsobjekte, Ber1 und Ber2, wobei Ber1 alle Berechtigungen (Administrator) und Ber2 Anmeldungsberechtigung hat. 5. Ordnen Sie Benutzer1 und Benutzer2 in Gruppe1 ein.
Sie können Schema Extender oder die LDIF-Dateien an einem beliebigen Standort kopieren und ausführen. Dell Schema Extender verwenden VORSICHT: Das Dienstprogramm Dell Schema Extender verwendet die Datei SchemaExtenderOem.ini. Um sicherzustellen, dass das Dell Schema Extender-Dienstprogramm richtig funktioniert, modifizieren Sie den Namen dieser Datei nicht. 1. Klicken Sie im Begrüßungsbildschirm auf Weiter. 2.
Tabelle 15. delliDRACAssociationObject Class OID 1.2.840.113556.1.8000.1280.1.7.1.2 Beschreibung Repräsentiert das Dell-Zuordnungsobjekt. Das Zuordnungsobjekt ist die Verbindung zwischen Benutzern und Geräten. Klassentyp Strukturklasse SuperClasses Gruppe Attribute dellProductMembers dellPrivilegeMember Tabelle 16. dellRAC4Privileges Class OID 1.2.840.113556.1.8000.1280.1.1.1.3 Beschreibung Definiert die Berechtigungen (Autorisierungsrechte) für das CMC-Gerät.
Tabelle 18. dellProduct Class OID 1.2.840.113556.1.8000.1280.1.1.1.5 Beschreibung Die Hauptklasse, von der alle Dell-Produkte abgeleitet werden. Klassentyp Strukturklasse SuperClasses Computer Attribute dellAssociationMembers Tabelle 19. Liste von Attributen, die dem Active Directory-Schema hinzugefügt wurden Zugewiesener OID/Syntax-Objektkennzeichner Einzelbewertung Attribut: dellPrivilegeMember FALSE Beschreibung: Liste mit dellPrivilegeObjekten, die zu diesem Attribut gehören. OID: 1.2.
Zugewiesener OID/Syntax-Objektkennzeichner Einzelbewertung Attribut: dellIsUserConfigAdmin TRUE Beschreibung: TRUE, wenn der Benutzer Benutzerkonfigurationsrechte auf dem Gerät hat. OID: 1.2.840.113556.1.8000.1280.1.1.2.5 Boolesch (LDAPTYPE_BOOLEAN 1.3.6.1.4.1.1466.115.121.1.7) Attribut: delIsLogClearAdmin TRUE Beschreibung: TRUE, wenn der Benutzer Administratorrechte zum Löschen von Protokollen auf dem Gerät hat. OID: 1.2.840.113556.1.8000.1280.1.1.2.6 Boolesch (LDAPTYPE_BOOLEAN 1.3.6.1.4.1.1466.115.
Zugewiesener OID/Syntax-Objektkennzeichner Einzelbewertung Zeichenfolge zum Ignorieren von Groß-/ Kleinschreibung (LDAPTYPE_CASEIGNORESTRING 1.2.840.113556.1.4.905) Attribut: dellRacType TRUE Beschreibung: Dieses Attribut ist der aktuelle RACTyp für das DellRacDevice-Objekt und die Rückwärtsverknüpfung zur Vorwärtsverknüpfung von dellAssociationObjectMembers. OID: 1.2.840.113556.1.8000.1280.1.1.2.13 Zeichenfolge zum Ignorieren von Groß-/ Kleinschreibung (LDAPTYPE_CASEIGNORESTRING 1.2.840.113556.1.4.
Weitere Informationen über Active Directory-Benutzer- und -Computer-Snap-In finden Sie in der Microsoft-Dokumentation. CMC-Benutzer und -Berechtigungen zum Active Directory hinzufügen Mit dem von Dell erweiterten Active Directory-Benutzer- und -Computer-Snap-In können Sie CMCBenutzer und -Berechtigungen hinzuzufügen, indem Sie RAC-Gerät-, Zuordnungs- und Berechtigungsobjekte erstellen.
3. Geben Sie auf der Seite Neues Objekt einen Namen für das neue Objekt ein und wählen Sie Zuordnungsobjekt aus. 4. Wählen Sie den Bereich für das Zuordnungsobjekt und klicken Sie auf OK. Objekte zu einem Zuordnungsobjekt hinzufügen Durch die Verwendung des Fensters Zuordnungsobjekt-Eigenschaften können Sie Benutzer oder Benutzergruppen, Berechtigungsobjekte und RAC-Geräte oder RAC-Gerätegruppen zuordnen.
ANMERKUNG: Weitere Informationen zu den verschiedenen Feldern finden Sie in der Online-Hilfe. 1. Klicken Sie im linken Fensterbereich auf Gehäuseübersicht → Benutzerauthentifizierung → Gehäuseübersicht → Verzeichnisdienste. 2. Wählen Sie Microsoft Active Directory (Erweitertes Schema) aus. Die Einstellungen, die für das erweiterte Schema vorzunehmen sind, werden auf derselben Seite angezeigt. 3.
11. Wenn DHCP verwenden für Netzwerkschnittstellen-IP-Adresse aktiviert ist, wählen Sie eine der folgenden Vorgehensweisen aus: • Wählen Sie DHCP zum Abrufen von DNS-Serveradressen verwenden aus, um die DNS-ServerAdressen zu aktivieren, die automatisch vom DHCP-Server abgerufen werden sollen.
Ein CMC-Administrator kann nun die LDAP-Server-Benutzeranmeldungen in den CMC integrieren. Diese Integration erfordert die Konfiguration sowohl des LDAP-Servers wie auch des CMC. Auf der Seite des LDAP-Servers wird ein Standardgruppenobjekt als Rollengruppe verwendet. Ein Benutzer, der Zugang zum CMC hat, wird ein Mitglied der Rollengruppe. Berechtigungen sind weiterhin auf dem CMC für die Authentifizierung gespeichert, ähnlich wie bei der Standardschema-Einrichtung mit Active DirectoryUnterstützung.
ANMERKUNG: Sie müssen die Berechtigung als Gehäusekonfiguration-Administrator besitzen. 1. Klicken Sie im linken Fensterbereich auf Gehäuse-Übersicht → Benutzerauthentifizierung → Verzeichnisdienste. 2. Wahlen Sie Allgemeines LDAP aus. Die Einstellungen, die für Standardschema konfiguriert werden sollen, werden auf derselben Seite angezeigt. 3. Geben Sie folgendes an: ANMERKUNG: Weitere Informationen zu den verschiedenen Feldern finden Sie in der OnlineHilfe.
Es gibt viele Möglichkeiten zur Konfiguration von LDAP-Anmeldungen. Meistens können einige Optionen in der Standardeinstellung verwendet werden. ANMERKUNG: Wir empfehlen dringend die Verwendung des Befehls racadm testfeature -f LDAP, um die LDAP-Einstellungen bei Ersteinrichtungen zu testen. Diese Funktion unterstützt sowohl IPv4 wie auch IPv6.
CMC für die einfache Anmeldung oder Smart Card-Anmeldung konfigurieren 10 Dieser Abschnitt enthält Informationen zum Konfigurieren von CMC für die Smart Card-Anmeldung sowie für die einfache Anmeldung (Single Sign-On, SSO) von Active Directory-Benutzern. SSO verwendet Kerberos als Authentifizierungsmethode, die Benutzern, die sich mit automatischer oder einfacher Anmeldung angemeldet haben, nachfolgende Anwendungen wie Exchange ermöglicht.
• DHCP-Server (empfohlen). • Die DNS-Server-Reverse-Zone muss einen Eintrag für den Active Directory-Server und den CMC enthalten. Client-Systeme • Für reine Smart Card-Anmeldung muss das Clientsystem die verteilbare Komponente von Microsoft Visual C++ 2005 enthalten. Weitere Informationen finden Sie unter www.microsoft.com/downloads/ details.
So generieren Sie eine Keytab-Datei mithilfe des ktpass-Tools: 1. Führen Sie das Dienstprogramm ktpass auf dem Domänen-Controller (Active Directory-Server) aus, auf dem Sie den CMC einem Benutzerkonto in Active Directory zuordnen möchten. 2. Verwenden Sie den folgenden ktpass-Befehl, um die Kerberos-Keytab-Datei zu erstellen: C:\>ktpass -princ HTTP/cmcname.domain_name.com@REALM_NAME.COM - mapuser dracname -crypto DES-CBC-MD5 -ptype KRB5_NT_PRINCIPAL -pass * -out c: \krbkeytab ANMERKUNG: Der cmcname.
Mozilla Firefox 1. Geben Sie in Firefox about:config in die Adressleiste ein. ANMERKUNG: Wenn der Browser die Warnung Das kann Ihre Garantie ungültig machen anzeigt, klicken Sie auf I'll be careful. I promise. 2. Im Textfeld Filter geben Sie negotiate (verhandeln) ein. Der Browser zeigt eine Liste bevorzugter Namen an, die alle das Wort „negotiate“ enthalten. 3. Doppelklicken Sie in der Liste auf network.negotiate-auth.trusted-uris. 4.
ANMERKUNG: Weitere Informationen zu den verfügbaren Optionen finden Sie in der Online-Hilfe. 1. 2. Führen Sie beim Konfigurieren von Active Directory zum Einstellen des Benutzerkontos die folgenden zusätzlichen Schritte aus: • Laden Sie die Keytab-Datei hoch. • Um SSO (Single Sign-On) zu aktivieren, wählen Sie die Option Einfache Anmeldung aktivieren aus. • Um Smart Card-Anmeldung zu aktivieren, wählen Sie die Option Smart-Card-Anmeldung aktivieren aus.
Konfigurieren der CMC SSO- oder Smart-Card-Anmeldung für Active Directory-Benutzer über RACADM Neben den im Rahmen der Konfiguration von Active Directory ausgeführten Schritten führen Sie zum Aktivieren von SSO den folgenden Befehl aus: racadm -g cfgActiveDirectory -o cfgADSSOEnable 1 Neben den im Rahmen der Konfiguration von Active Directory ausgeführten Schritten verwenden Sie zum Aktivieren der Smart Card-Anmeldung die folgenden Objekte: • cfgSmartCardLogonEnable • cfgSmartCardCRLEnable 164
CMC zur Verwendung von Befehlszeilenkonsolen konfigurieren 11 Dieser Abschnitt enthält Informationen über die Funktionen der CMC-Befehlszeilenkonsole (bzw. der serielle/Telnet-/Secure Shell-Konsole) und erklärt, wie das System eingerichtet wird, sodass Systemverwaltungsmaßnahmen über die Konsole ausgeführt werden können.
Befehl Beschreibung ANMERKUNG: Sie können auch den RACADM Befehl connect verwenden. exit, logout und quit Alle diese Befehle führen die gleiche Maßnahme aus. Sie beenden die aktuelle Sitzung und kehren zu einer Anmeldungsbefehlszeilenschnittstelle zurück. Telnet-Konsole mit dem CMC verwenden Mit CMC können Sie bis zu vier Telnet-Sitzungen gleichzeiting durchführen.
Benutzer-ID/Kennwort einzubetten bzw. anzufordern. Weitere Informationen finden Sie unter Konfigurieren der Authentifizierung mit öffentlichem Schlüssel über SSH. SSH ist standardmäßig aktiviert. Falls SSH deaktiviert ist, können Sie die Option mit jeder anderen unterstützten Schnittstelle aktivieren. Zur Konfiguration von SSH gehen Sie zu Dienste konfigurieren.
Hinzufügen eines Schlüssels keine Prüfungen durch, um sicherzustellen, dass keine vorherigen Schlüssel gelöscht werden. Sobald ein neuer Schlüssel hinzugefügt wurde, tritt er automatisch in Kraft, solange die SSH-Schnittstelle aktiviert ist. Beachten Sie bei Verwendung des Anmerkungsabschnitts des öffentlichen Schlüssels, dass nur die ersten 16 Zeichen vom CMC verwendet werden.
wobei –t- „dsa“ oder „rsa“ sein muss. –b die Bit-Verschlüsselungsgröße zwischen 768 und 4096 angibt. –c das Ändern der Anmerkung des öffentlichen Schlüssels ermöglicht und optional ist. Die ist optional. Wenn der Befehl beendet ist, verwenden Sie die öffentliche Datei zur Übergabe an den RACADM zum Hochladen der Datei. Hinweise zur RACADM-Syntax für CMC Wenn Sie den Befehl racadm sshpkauth verwenden, stellen Sie Folgendes sicher: • Bei der Option –i muss der Parameter svcacct sein.
Terminalemulationssoftware konfigurieren CMC unterstützt eine serielle Textkonsole einer Management Station, auf der einer der folgenden Typen der Terminalemulationssoftware ausgeführt wird: • Linux Minicom • Hilgraeve HyperTerminal Private Edition (Version 6.3) Um den erforderlichen Typ der Terminalsoftware zu konfigurieren, beenden Sie die in den folgenden Unterabschnitten aufgeführten Tasks.
Erforderliche Minicom-Einstellungen Verwenden Sie die folgende Tabelle zum Konfigurieren einer beliebigen Minicom-Version. Tabelle 22.
Um eine Verbindung zu einem EAM herzustellen, geben Sie Folgendes ein: connect switch-n wobei n eine EAM-Kennungszeichnung A1 ist. Wenn Sie sich beim connect-Befehl auf die EAMs beziehen, werden den EAMs-Switches zugeordnet, wie in der folgenden Tabelle dargestellt. Tabelle 23. E/A-Module zu Switches zuordnen E/A-Modulkennzeichnung Switch A1 switch-a1 oder switch-1 ANMERKUNG: Es kann jeweils nur eine EAM-Verbindung pro Gehäuse aktiv sein.
3. Gehen Sie zu Serielle Kommunikation und drücken Sie die Taste . Im Dialogfeld wird die Liste der seriellen Kommunikation mit den folgenden Optionen angezeigt: • Aus • Ein ohne Konsolenumleitung • Ein mit Konsolenumleitung über COM1 Um zwischen Optionen hin und her zu navigieren, verwenden Sie die entsprechenden Pfeiltasten. ANMERKUNG: Achten Sie darauf, dass die Option Ein mit Konsolenumleitung über COM1 ausgewählt ist. 4.
3. Wenn /etc/grub.conf eine splashimage-Direktive enthält, kommentieren Sie sie aus. Im folgenden Beispiel sind die Änderungen zu sehen, die in diesem Verfahren beschrieben werden. # grub.conf, erstellt durch anaconda # # Beachten Sie, dass grub nicht erneut ausgeführt werden muss, nachdem Sie Änderungen an # dieser Datei # vorgenommen haben. HINWEIS: Sie haben keine /boot-Partition. Dies bedeutet, dass # alle Kernel und initrd-Pfade relativ zu / sind, z. B.
Edit the /etc/securettyfile as follows: Fügen Sie eine neue Zeile mit dem Namen des seriellen tty für COM2 hinzu: ttyS1 Das folgende Beispiel zeigt eine Beispieldatei mit der neuen Zeile.
12 FlexAddress- und FlexAdress Plus-Karten verwenden Dieser Abschnitt enthält Informationen über FlexAddress- und FlexAddress Plus-Karten und das Konfigurieren und Verwenden dieser Karten. ANMERKUNG: Auf dem CMC muss eine Enterprise-Lizenz installiert sein, um die FlexAddressFunktion verwenden zu können.
Beispiel: (starting_mac)00188BFFDCFA + 0xCF = (ending_mac)00188BFFDDC9 . ANMERKUNG: Sperren Sie die SD-Karte vor dem Einsetzen in den USB-Speicherkartenleser, um versehentliches Ändern des Inhalts zu verhindern. Die SD-Karte muss entsperrt werden, bevor Sie sie in den CMC einsetzen. Über FlexAddress Plus FlexAddress Plus ist eine neue Funktion bei der Kartenversion 2.0. Es ist eine Erweiterung der FlexAddress-Funktionskarte Version 1.0.
3. Aktualisieren Sie die gesamte CMC-Firmware im Gehäuse; falls redundante CMCs vorhanden sind, stellen Sie sicher, dass beide aktualisiert sind. 4. Legen Sie die SD-Karte in das passive Modul ein für ein redundantes CMC-Modulsystem oder in das einzige CMC-Modul für ein nicht-redundantes System.
Um den FlexAddress-Status für das Gehäuse mithilfe der CMC-Webschnittstelle anzuzeigen, gehen Sie zu Gehäuseübersicht → Setup. Die Seite Allgemeine Gehäuseeinstellungen wird angezeigt. Der Eintrag für FlexAddress weist den Wert Aktiv oder Nicht Aktiv auf. Der Wert Aktiv bedeutet, dass die Funktion für das Gehäuse installiert ist, während Nicht aktiv bedeutet, dass die Funktion für das Gehäuse nicht installiert wurde und daher nicht verfügbar ist.
In diesem Fall zeigt der Befehl „racadm feature -s“ die folgende Meldung für die betroffenen Funktionen an: ERROR: One or more features on the SD card are active on another chassis Weitere Informationen über die Befehle feature und featurecard finden Sie im Chassis Management Controller for PowerEdge VRTX RACADM Command Line Reference Guide (RACADM-BefehlszeilenReferenzhandbuch für Chassis Management Controller für PowerEdge VRTX).
Anzeigen der FlexAddress-Gehäuseinformationen Die FlexAddress-Statusinformationen können für das gesamte Gehäuse angezeigt werden. Die Statusinformationen beinhalten, ob die Funktion aktiv ist, und einen Überblick über den FlexAddressStatus für jeden Server.
Anzeige der FlexAddress Informationen für einzelne Server So werden FlexAddress-Informationen für einen bestimmten Server unter Verwendung der CMCWebschnittstelle angezeigt: 1. Erweitern Sie im linken Fensterbereich Server-Übersicht. Alle Server, die sich im Gehäuse befinden sind aufgelistet. 2. Klicken Sie auf den Server, den Sie anzeigen möchten. Die Seite Serverstatus wird angezeigt. 3. Klicken Sie auf das Register Setup und dann auf FlexAddress.
Wake-On-LAN mit FlexAddress Wenn die FlexAddress-Funktion zum ersten Mal auf einem Servermodul bereitgestellt wird, erfordert dies ein Herunterfahren und erneutes Hochfahren, damit FlexAddress wirksam wird. FlexAddress auf EthernetGeräten wird vom BIOS des Systemmoduls programmiert. Damit das BIOS des Servermoduls die Adresse programmieren kann, muss es in Betrieb sein, was erfordert, dass das Servermodul eingeschaltet ist.
0 bedeutet deaktiviert und 1 bedeutet aktiviert. Verwenden Sie zum Aktivieren oder Deaktivieren von Steckplätzen die folgenden RACADM-Befehle: racadm setflexaddr [-i wobei = 1 or 4 und = 0 or 1 0 bedeutet deaktiviert und 1 bedeutet aktiviert.
Situation Befehl Output (Ausgabe) ungültig und enthält die folgenden Funktionen FlexAddress: Die Funktionskarte ist an ein anderes Gehäuse gebunden, svctag = SD-Karte SN = SD-Karte im aktiven CMC-Modul ist an die gleiche Service-TagNummer gebunden.
Situation Befehl sie einen eingeschalteten Server betrifft während die Servermodule eingeschaltet sind. Flexaddress-Einstellungen auf Steckplatz oder Struktur ändern, wenn die CMC Enterprise-Lizenz nicht installiert ist. Output (Ausgabe) $racadm setflexaddr i $racadm setflexaddr [-f ] FEHLER: SWC0242 : Eine erforderliche Lizenz fehlt oder ist abgelaufen.
erklären Sie sich damit einverstanden, Dell bei einem solchen Audit zu unterstützen und Dell alle Aufzeichnungen zur Verfügung zu stellen, die billigerweise mit der Verwendung der Software in Beziehung stehen. Das Audit beschränkt sich auf die Überprüfung der Einhaltung der Bestimmungen dieser Vereinbarung. Die Software ist durch US-amerikanische Urheberrechtsgesetze und Bestimmungen internationaler Verträge geschützt.
DELL HAFTET NICHT FÜR DIREKTE ODER INDIREKTE SCHÄDEN (DIES GILT UNTER ANDEREM AUCH OHNE BESCHRÄNKUNG FÜR FOLGESCHÄDEN JEGLICHER ART, FÜR SCHÄDEN DURCH ENTGANGENE GEWINNE, BETRIEBSUNTERBRECHUNGEN, VERLUST VON GESCHÄFTSDATEN ODER SONSTIGE PEKUNIÄRE VERLUSTE), DIE AUS DER VERWENDUNG ODER DER FEHLENDEN MÖGLICHKEIT, DIE SOFTWARE ZU VERWENDEN, ENTSTEHEN, AUCH WENN AUF DIE MÖGLICHKEIT DES ENTSTEHENS SOLCHER SCHÄDEN HINGEWIESEN WURDE.
möglicherweise nicht. Sie bestätigen hiermit, dass Sie diese Vereinbarung gelesen und verstanden haben, dass Sie sich an die vorgenannten Bestimmungen halten und dass diese Vereinbarung hinsichtlich der Software die vollständige und exklusive Vereinbarung zwischen Ihnen und Dell darstellt.
Verwalten von Strukturen 13 Das Gehäuse unterstützt einen Strukturtyp: Struktur A. Struktur A wird von dem einen E/A Modul verwendet, und ist stets mit den integrierten Ethernet-Adaptern der Server verbunden. Das Gehäuse enthält nur ein E/A-Module (EAM), das entweder ein Switch- oder Passthrough-Modul sein kann. Das E/A-Modul wird als Gruppe A klassifiziert. Der Gehäuse EAM verwendet einen diskrete Datenpfad: Struktur, und wird A genannt. Struktur A unterstützt nur Ethernet.
Nachdem sich die EAMs eingeschaltet haben, schalten sich die Server ein, und der CMC überprüft die Server auf Strukturkonsistenz. Ein Passthrough-Modul und ein Switch sind in der gleichen Gruppe zugelassen, wenn deren Struktur identisch ist. Switches und Passthrough-Module können in derselben Gruppe existieren, auch wenn Sie von unterschiedlichen Herstellern stammen.
3. Klicken Sie auf Anwenden. Die Netzwerkeinstellungen sind für das IOM konfiguriert. ANMERKUNG: Falls zugelassen, können Sie die VLANs, Netzwerkeigenschaften und E/ASchnittstellen auf die Standardkonfiguration zurückzusetzen.. Konfigurieren von Netzwerkeinstellungen für EAMs unter Verwendung von RACADM Um die Netzwerkeinstellungen für EAMs mit RACADM zu konfigurieren, stellen Sie das Datum und die Uhrzeit ein.
14 Energieverwaltung und -überwachung Das Dell PowerEdge VRTX-Gehäuse ist der energieeffizienteste modulare Server auf dem Markt. Er ist für hocheffiziente Netzteile und Lüfter konzipiert, verfügt über ein optimiertes Layout, sodass die Luft leichter durch das System strömen kann, und verfügt im gesamten Gehäuse über energieoptimierte Komponenten.
Redundanzregeln Eine Redundanzregel ist ein konfigurierbarer Satz von Eigenschaften, die festlegen, wie der CMC den Strom im Gehäuse verwaltet. Die folgenden Redundanzregeln sind mit oder ohne dynamische Zuschaltung von Netzteileinheiten konfigurierbar: • Netzredundanz • Netzteilredundanz Netzredundanzregeln Die Netzredundanzregel macht es möglich, dass ein modulares Gehäusesystem in einem Modus betrieben wird, in dem es Netzstromausfälle überbrücken kann.
Die Netzteilredundanz-Richtlinie Der Netzteilredundanz-Richtlinie ist nützlich, wenn keine redundanten Stromnetze zur Verfügung stehen und Schutz gegen den Ausfall einer einzelnen Netzteileinheit erwünscht ist, um den Ausfall der Server in einem modularen Gehäuse zu vermeiden. Für diesen Zweck wird die Netzteileinheit mit der größten Kapazität als Onlinereserve gehalten. Das bildet einen Netzteilredundanzpool.
als Online markiert. Der Stromverbrauch wird überwacht. Je nach Gesamtsystemlast kann eine Netzteileinheit in den Standby-Zustand gesetzt werden. In einer Konfiguration mit vier Netzteileinheiten sind immer mindestens zwei Netzteileinheiten eingeschaltet.
Netzteil-Redundanz Wenn Netzteilredundanz aktiviert ist, befindet sich eine Ersatz-Netzteileinheit im Gehäuse. Diese stellt sicher, dass der Ausfall einer anderen Netzteileinheit nicht dazu führt, dass die Stromversorgung der Server oder des Gehäuses unterbrochen wird. Der Netzteilredundanzmodus erfordert mindestens zwei Netzteileinheiten.
innerhalb eines festgelegten Schwellenwerts bleibt. Zunächst stellt der CMC sicher, dass ausreichend Strom für die Lüfter, E/A-Module, Speicheradapter, physisches Festplattenlaufwerk, Hauptplatine, und den CMC selbst verfügbar ist. Diese Stromzuteilung wird als der Gehäuseinfrastruktur zugewiesener Eingangsstrom bezeichnet. Nach der Gehäuseinfrastruktur werden die Server in einem Gehäuse eingeschaltet. Jeder Versuch, die Systemeingangsstromobergrenze unter der „Strombelastung“ anzusetzen, schlägt fehl.
Stromzuteilung bevorzugt werden sollen. Wenn für die kritischeren Servermodule die StandardSteckplatzpriorität von 1 beibehalten wird und die Priorität der weniger kritischen Servermodule auf den Prioritätswert 2 oder niedriger gesetzt werden, werden die Servermodule mit der Priorität 1 zuerst hochgefahren. Diese Server mit höherer Priorität erhalten ihre maximale Stromzuteilung, während die Server mit niedrigerer Priorität eventuell nicht genug Strom erhalten, um ihre maximale Leistung zu erbringen.
wobei sich (1-4) auf die Position des Servers bezieht und der Wert für die zwischen 1 und 9 liegt. Beispiel: Um die Prioritätsstufe 1 für den Server in Steckplatz 4 einzustellen, geben Sie den folgenden Befehl ein: racadm config -g cfgServerInfo -o cfgServerPriority -i 4 1 Anzeige des Stromverbrauchsstatus Der CMC zeigt den tatsächlichen Eingangsstromverbrauch für das gesamte System auf der Seite Stromverbrauchsstatus an.
Redundanzstatus und allgemeiner Stromzustand Der Redundanzstatus ist ein Faktor zur Bestimmung des allgemeinen Stromzustands. Wenn die Stromredundanzregel beispielsweise auf „Wechselstromredundanz“ festgelegt wird und der Redundanzstatus anzeigt, dass das System mit Redundanz arbeitet, ist der allgemeine Stromzustand in der Regel OK. Wenn jedoch die Bedingungen für den Betrieb mit Netzredundanz nicht erfüllt werden können, ist der Redundanzstatus Keine und der allgemeine Stromzustand Kritisch.
der Administrator eine Stromgrenze für das Gehäuse konfiguriert hat, die unter dem Wert liegt, der für eine vollständige Stromzuweisung für den Server nötig wäre, oder wenn unzureichend Strom verfügbar ist im Falle von höheren Stromanforderungen von allen Servern im Gehäuse. Wenn durch die Reduktion des zugewiesenen Stroms der Server mit niedriger Priorität nicht genügend Strom freigesetzt werden kann, kann der neue Server nicht gestartet werden.
Konfiguration der Netzteileinheiten Dynamische Zuschaltung von Netzteileinheiten Firmware-Reaktion vorhanden) werden eingeschaltet, um den Stromverlust in Folge eines Netzteileinheitfehlers oder -ausfalls zu kompensieren. Netzteil-Redundanz Aktiviert Der CMC alarmiert bei Verlust der Netzteilredundanz. Netzteile im Standby-Modus (wenn vorhanden) werden eingeschaltet, um den Stromverlust in Folge eines Netzteileinheitfehlers oder -ausfalls zu kompensieren.
Sie können Folgendes konfigurieren: • Systemeingangsstrom-Obergrenze • Redundanzregel • Dynamische Netzteil-Einsatzfähigkeit aktivieren • Netzschalter des Gehäuses deaktivieren • Max. Stromkonservierungsmodus • Remote-Stromprotokollierung • Remote-Stromverbrauchsprotokollierungszeitraum • Serverbasierte Stromverwaltung Stromeinsparung und Strombudget Der CMC kann Strom einsparen, wenn die vom Benutzer konfigurierte maximale Stromgrenze erreicht ist.
Systemeingangsstromobergrenze zu halten. Wenn beispielsweise ein neuer Server zugeschaltet wird, kann der CMC die Stromzufuhr zu Servern mit niedriger Priorität verringern, um den neuen Server mit mehr Strom zu versorgen. Wenn die Strommenge nach der Verringerung der Stromzuteilung zu Servern mit niedriger Priorität nach wie vor nicht ausreicht, drosselt der CMC die Server mit höherer Priorität bis ausreichend Strom freigegeben ist, um den neuen Server mit Strom zu versorgen.
PM3 verwaltet die Server-Stromversorgung und die Prioritäten direkt. Da PM3 kompatible Serverstromversorgungszuweisungen steuert, steuert CMC nicht mehr den maximalen Stromsparmodus. Damit ist diese Option nicht mehr auswählbar. Wenn der maximale Stromsparmodus aktiviert ist, setzt CMC die Eingangsstromkapazität des Systems auf den Maximalwert, den das Gehäuse verarbeiten kann. Bei CMC darf die Stromversorgung die höchst mögliche Kapazität nicht überschreiten.
So aktivieren Sie die Redundanz und legen die Redundanzregel fest: 1. Öffnen Sie eine serielle, Telnet- oder SSH-Textkonsole für den CMC und melden Sie sich an. 2. Legen Sie die Eigenschaften nach Bedarf fest: • Um eine Redundanzregel auszuwählen, geben Sie Folgendes ein: racadm config -g cfgChassisPower -o cfgChassisRedundancyPolicy wobei = 1 (Grid-Redundanz) und 2 (Netzteilredundanz) lautet. Der Standardwert ist 2.
• Um die Remote-Energieverwaltung durch Open Manage Power Center (OPMC) zu aktivieren, geben Sie Folgendes ein: racadm config -g cfgChassisPower -o cfgChassisServerBasedPowerMgmtMode 1 • Um die CMC-Energieverwaltung wiederherzustellen, geben Sie Folgendes ein: racadm config -g cfgChassisPower -o cfgChassisServerBasedPowerMgmtMode 0 Weitere Informationen zu den RACADM-Befehlen für die Gehäusestromversorgung finden Sie in den Abschnitten config, getconfig, getpbinfo und cfgChassisPower im Chassis Manageme
Energieverwaltungsmaßnahmen am Gehäuse über RACADM durchführen Öffnen Sie eine serielle, Telnet- oder SSH-Textkonsole für den CMC, melden Sie sich an und geben Sie Folgendes ein: racadm chassisaction -m chassis wobei powerup, powerdown, powercycle, nongraceshutdown oder reset ist. Durchführen von Energieverwaltungsmaßnahmen an einem Server Sie können im Remote-Zugriff Stromverwaltungsmaßnahmen für mehrere Server gleichzeitig oder einen individuellen Server im Gehäuse durchführen.
Stromsteuerungsvorgänge auf EAM unter Verwendung der CMCWebschnittstelle ausführen So führen Sie auf einem E/A-Modul Stromsteuerungsvorgänge aus: 1. Klicken Sie im linken Fensterbereich auf Gehäuseübersicht → E/A-Modul-Übersicht → Strom. 2. Wählen Sie auf der Seite Stromsteuerung für EAM aus dem Drop-Down-Menü den Vorgang aus, den Sie ausführen möchten (Aus- und einschalten). 3. Klicken Sie auf Anwenden.
Verwaltung von Gehäusespeichern 15 Sie können auf Dell PowerEdge VRTX folgende Aufgaben ausführen: • Den Status von physischen Festplattenlaufwerken und Speicher-Controllern anzeigen. • Die Eigenschaften von Controllern, physischen Festplattenlaufwerken, virtuellen Festplatten und Gehäusen anzeigen. • Controller, physische Festplattenlaufwerke und virtuelle Festplatten einrichten. • Virtuelle Adapter zuweisen.
Anzeigen der Speichertopologie So zeigen Sie die Speichertopologie an: 1. Klicken Sie im linken Fensterbereich auf Gehäuseübersicht → Speicher → Eigenschaften → Topologie. 2. Klicken sie auf der Seite Topologie auf , um die entsprechenden Seiten anzuzeigen. ANMERKUNG: Sie können den Namen des Controllers anzeigen, der sich aktiv an der Steuerung der Speichergeräte im Zusammenhang mit dem CMC beteiligt, und auch die passiven Controller, die als Stand-by fungieren. 3.
Anzeigen von Informationen zur fehlertoleranten Fehlerbehebung von SPERC über die CMCWebschnittstelle Gehen Sie wie folgt vor, um die Attribute anzuzeigen, die die korrekte Funktionsweise der Fehlertoleranzfunktionen eines SPERC anzeigen. 1. Klicken Sie im linken Fensterbereich auf Gehäuseübersicht → Speicher → Fehlerbehebung → Fehlerbehebung einrichten. Die Seite Speicherfehlerbehebung wird angezeigt. 2.
– der Serversteckplatz leer ist, oder dass der Server im Steckplatz ausgeschaltet ist. – Die Zuordnung eines virtuellen Adapters wird von einem Server oder einem Steckplatz aufgehoben. – Alle betroffenen Server sind ausgeschaltet. • Virtuelle Festplatten werden erstellt und als Virtueller Adapter 1, Virtueller Adapter 2, Virtueller Adapter 3 oder Virtueller Adapter 4 zugewiesen. Weitere Informationen finden Sie unter Zugangsrichtlinien für virtuelle Adapter auf virtuelle Festplatten anwenden.
3. Wählen Sie in der Tabelle Zuordnung virtueller Netzwerkadapter im Drop-Down-Menü Aktion eine der folgenden Optionen aus, und klicken Sie dann auf Anwenden. • – Wählen Sie den Steckplatz aus, dem der virtuelle Adapter zugewiesen werden muss. • Zuordnung aufheben – Wählen Sie aus, die Zuweisung des virtuellen Adapters zu einem Steckplatz zu entfernen. Der virtuelle Adapter wird vom ausgewählten Serversteckplatz aus zugeordnet, oder die Zuordnung wird entsprechend aufgehoben.
Anzeigen von Gehäuseeigenschaften unter Verwendung der CMC-Webschnittstelle So können Sie die Controller-Eigenschaften anzeigen: 1. Klicken Sie im linken Fensterbereich auf Gehäuseübersicht → Controller. 2. Sie können auf der Seite Controller, unter dem Abschnitt Controller die grundlegenden Eigenschaften der Controller anzeigen. Um jedoch die erweiterten Eigenschaften anzuzeigen, klicken Sie auf das .
So konfigurieren Sie die Speicher-Controller-Einstellungen: 1. Gehen Sie in der CMC-Webschnittstelle zu Gehäuseübersicht → Speicher → Controller → Setup. 2. Wählen Sie auf der Seite Controller-Setup aus dem Drop-Down-Menü Controller den Controller aus. ANMERKUNG: Beachten Sie Folgendes: • Wenn es sich um Speicher-Controller im fehlertoleranten Modus handelt und wenn beide die gleiche Firmware-Version haben, werden beide Controller als ein einziges Gerät im Drop-Down-Menü angezeigt.
So zeigen Sie die Eigenschaften physischer Festplattenlaufwerke an: 1. Klicken Sie im linken Fensterbereich auf Gehäuseübersicht → Speicher → Physische Festplatten. Die Seite Eigenschaften wird angezeigt. 2. Um die Eigenschaften aller physischer Festplattenlaufwerke anzuzeigen, klicken sie im Abschnitt Physische Festplatten auf das .
Globalen Hotspare unter Verwendung von RACADM zuweisen Um globale Hotspare unter Verwendung von RACADM zuzuweisen, führen Sie den Befehl racadm raid hotspare: -assign yes -type ghs aus. Weitere Informationen über RACADM-Befehle finden Sie im Chassis Management Controller for PowerEdge VRTX RACADM Command Line Reference Guide (RACADM-Befehlszeilen-Referenzhandbuch für Chassis Management Controller für PowerEdge VRTX).
Erstellung von virtuellen Festplatten unter Verwendung der CMC-Webschnittstelle Achten Sie darauf, dass die physische Festplatte im Gehäuse installiert ist. ANMERKUNG: Das Löschen einer virtuellen Festplatte entfernt die virtuelle Festplatte aus der Konfiguration des Controllers. So erstellen Sie eine virtuelle Festplatte: 1. Klicken Sie im linken Fensterbereich auf Gehäuseübersicht → Speicher → Virtuelle Festplatten → Erstellen. 2.
Ändern der Eigenschaften von virtuellen Festplatten unter Verwendung der CMC Web-Schnittstelle So ändern Sie die Eigenschaften virtueller Festplatten: 1. Klicken Sie im linken Fensterbereich auf Gehäuseübersicht → Speicher → Virtuelle Festplatten → Verwalten. 2. Wählen Sie aus der Seite Virtuelle Laufwerke verwalten das Drop-Down-Menü Maßnahmen für virtuelle Festplatten aus, wählen Sie eine der folgenden Maßnahmen, und klicken Sie dann auf Anwenden.
16 PCIe-Steckplätze.verwalten Standardmäßig sind keine Steckplätze zugewiesen. Sie können Folgendes ausführen: • Sie können den Status aller PCIe-Steckplätze im Gehäuse anzeigen. • Weisen Sie den Servern einen zugewiesenen PCIe-Steckplatz zu, oder heben Sie die Zuweisung auf. Berücksichtigen Sie die folgenden Faktoren, bevor Sie einem Server einen PCIe-Steckplatz zuweisen: • Ein leerer PCIe-Steckplatz kann einem Server, der eingeschaltet ist, nicht zugewiesen werden.
• Klicken Sie im linken Fensterbereich auf Gehäuseübersicht → PCIe-Übersicht → Setup → Zuordnung: PCIe-Steckplätze zu Server-Steckplätzen. Wählen Sie auf der Seite Zuordnung: PCIeSteckplätze zu Server-Steckplätzen in der Spalte Maßnahme aus dem Drop-Down-Menu Maßnahme den entsprechenden Servernamen aus, und klicken Sie dann auf Anwenden. Beachten Sie Folgendes: • Ohne Lizenz können Sie einem Server mit halber Höhe maximal zwei PCIe-Slots zuordnen.
• Um zum Beispiel PCIe-Steckplatz 5 dem Serversteckplatz 2 zuzuweisen, führen Sie den folgenden Befehl aus. racadm setpciecfg assign -c PCIE.ChassisSlot.5 -i 2 • Um die Zuweisung von PCIe-Steckplatz 3 von einem Server rückgängig zu machen, führen Sie den folgenden Befehl aus: racadm setpciecfg unassign -c pcie.chassisslot.3 PCIe-Energieüberbrückung Die neu zugewiesenen PCIe-Karten in CMC VRTX müssen ermittelt und initialisiert werden, bevor ein Server-Knoten eingeschaltet wird.
Anzeigen von PCIe-Überbrückungseigenschaften über die CMC Webschnittstelle Klicken Sie zum Anzeigen der PCIe-Überbrückungseigenschaften im linken Fenster auf Gehäuseübersicht → PCIe-Übersicht. Daraufhin wird die Seite PCIe-Status angezeigt. In Abschnitt Allgemeinen Einstellungen werden die folgenden PCIe-Überbrückungseigenschaftsstatus angezeigt: • Überbrückungsstatus – Aktiviert oder Deaktiviert • Überbrückung - Zeitüberschreitung – Gibt die Zeit an, für die die Überbrückungsfunktion aktiviert ist.
• Führen Sie zum Festlegen eines akzeptablen Zeitüberschreitungsbereichs den Befehl racadm setpciecfg help ridethru aus. Weitere Informationen finden Sie im Chassis Management Controller for PowerEdge VRTX RACADM Command Line Reference Guide (RACADM-Befehlszeilen-Referenzhandbuch für Chassis Management Controller für PowerEdge VRTX).
17 Fehlerbehebung und Wiederherstellung Dieser Abschnitt erklärt, wie Tasks unter Verwendung der CMC-Webschnittstelle ausgeführt werden, die sich auf die Wiederherstellung und Behebung eines Problems auf dem Remote-System beziehen. • Gehäuseinformationen anzeigen. • Ereignisprotokolle anzeigen. • Konfigurationsinformationen sammeln, Fehlerstatus und Fehlerprotokolle. • Diagnosekonsole verwenden. • Strom auf einem Remote-System verwalten.
racdump beinhaltet die folgenden Untersysteme und verbindet die folgenden RACADM-Befehle: Weitere Informationen zu racdump finden Sie im RACADM Command Line Reference Guide for CMC in PowerEdge VRTX (RACADM-Befehlszeilen-Referenzhandbuch für CMC in PowerEdge VRTX).
• Wenn ausgeschaltet, wurde der Strom unerwartet ausgeschaltet? Strombezogene Fehlerbehebung Die folgenden Informationen sind Ihnen bei der Fehlerbehebung bei Netzteilen und bei der Stromversorgung hilfreich: • Problem: Die Stromredundanzregel ist auf Netzredundanz eingestellt und es wurde ein KeineNetzteilredundanz-Ereignis gemeldet.
Strom durch Verringerung von Serverleistung zugewiesen wird, so dass die Eingangsleistungsaufnahme unterhalb der Eingangsleistungsgrenze des Systems gehalten werden kann. Dieses Verhalten ist normal. • Problem: W wird als Überschuss für Systemspitzen gemeldet.
ANMERKUNG: Um das Hardwareprotokoll zu löschen, müssen Sie die Berechtigung als Administrator zum Löschen von Protokollen besitzen. ANMERKUNG: Sie können den CMC so konfigurieren, dass E-Mail- oder SNMP-Traps gesendet werden, wenn bestimmte Ereignisse auftreten. Informationen zur Konfiguration des CMC zum Aussenden von Warnungen finden Sie unter Konfigurieren von CMC zum Senden von Warnungen. Beispiele von Hardwareprotokolleinträgen Kritisches Systemsoftwareereignis: Redundanz verloren Mittwoch, 09.
Gehäuseprotokoll anzeigen Der CMC erstellt ein Protokoll von Ereignissen, die sich auf das Gehäuse beziehen. ANMERKUNG: Um das Gehäuseprotokoll zu löschen, müssen Sie die Berechtigungen als Administrator zum Löschen von Protokollen aufweisen.
Komponenten zurücksetzen Sie können den aktiven CMC zurücksetzen oder Server virtuell neu einsetzen und somit bewirken, dass diese sich so verhalten, als seien sie herausgenommen und wieder eingesetzt worden. Falls das Gehäuse einen Standby-CMC aufweist, bewirkt das Zurücksetzen des aktiven CMC einen Failover, und der Standby-CMC wird aktiviert. ANMERKUNG: Zum Zurücksetzen von Komponenten müssen Sie die Berechtigung als DebugBefehl-Administrator besitzen.
Falls danach noch immer keine Änderung auftritt, handelt es sich möglicherweise um ein Problem, das untersucht werden muss. Der CMC kann seine Uhr möglicherweise aus folgenden Gründen nicht synchronisieren: • Es könnte ein Problem mit den NTP-Server 1-, NTP-Server 2- und NTP-Server 3-Einstellungen vorliegen. • Es wurden versehentlich ein ungültiger Hostname oder eine ungültige IP-Adresse eingegeben.
Falls eine NTP-Server-Einstellung mit einem ungültigen Hostnamen konfiguriert wurde, enthält das Ablaufverfolgungsprotokoll u. U. einen Eintrag der folgenden Art: Aug 21 14:34:27 cmc ntpd_initres[1298]: host name not found: blabla Aug 21 14:34:27 cmc ntpd_initres[1298]: couldn't resolve `blabla', giving up on it Weitere Informationen zur Eingabe des Befehls gettracelog zur Prüfung des Ablaufverfolgungsprotokolls unter Verwendung der CMC-Schnittstelle finden Sie unter Diagnosekonsole verwenden.
Komponente LED-Farbe, Blinkmuster Status E/A-Modul (Allgemein) Grün, beständig leuchtend Eingeschaltet Grün, blinkend Firmware wird hochgeladen Grün, dunkel Ausgeschaltet Blau, beständig leuchtend Normal/übergeordneter Stapel Blau blinkend Vom Benutzer aktivierte Modulidentifizierung Gelb, beständig leuchtend Nicht verwendet Gelb blinkend Fehler Blau, dunkel Kein Fehler/untergeordneter Stapel Grün, beständig leuchtend Eingeschaltet Grün, blinkend Nicht verwendet Grün, dunkel Ausgesc
Fehlerbehebung an einem CMC, der nicht mehr reagiert Wenn Sie sich nicht über eine der Schnittstellen beim CMC anmelden können (Webschnittstelle, Telnet, SSH, Remote-RACADM oder seriell), können Sie die Funktionsfähigkeit des CMC durch Beobachtung der LEDs auf dem CMC überprüfen, Wiederherstellungsinformationen über die serielle DB-9-Schnittstelle abrufen oder das CMC-Firmware-Abbild wiederherstellen. ANMERKUNG: Es ist nicht möglich, sich über eine serielle Konsole beim Standby-CMC anzumelden.
3. Drücken Sie die Eingabetaste. Wenn die Eingabeaufforderung Wiederherstellung angezeigt wird, stehen zusätzliche Informationen zur Verfügung. Die Eingabeaufforderung zeigt die CMC-Steckplatznummer und den Fehlertyp an. Um die Ursache des Fehlers und die Syntax für einige Befehle anzuzeigen, geben Sie recover ein und dann drücken Sie die Taste .
Das Ablaufverfolgungsprotokoll kann auch spezifische Fehlercodes der CMC-Firmware enthalten, die sich auf die interne CMC-Firmware beziehen und nicht auf das Betriebssystem des verwalteten Systems. Fehlerbehebung: Controller So führen Sie eine Fehlerbehebung an einem Controller aus: 1. Klicken Sie im linken Fensterbereich auf Gehäuseübersicht → Speicher → Gehäuse → Fehlerbehebung. 2.
LCD-Schnittstelle verwenden 18 Über das LCD-Bedienfeld des Gehäuses können Sie Konfigurationen und Diagnosen durchführen und Statusinformationen zum Gehäuse und dessen Inhalt abrufen. In der folgenden Abbildung wird das LCD Bedienfelt veranschaulicht. Auf dem LCD-Bildschirm werden Menüs, Symbole, Bilder und Meldungen angezeigt. Abbildung 2. LCD-Anzeige 1. 3. LCD-Bildschirm Scrolltasten (4) 2.
Die in der folgenden Tabelle beschriebenen Symbole werden zum Wechseln zwischen LCD-Bildschirmen verwendet. Tabelle 32. LCD-Bedienfeld-Navigationssymbole Symbol Normal Symbol markiert Symbolname und -beschreibung Zurück – Markieren und drücken Sie die mittlere Schaltfläche, um zum vorhergehenden Bildschirm zurückzukehren. Annehmen/Ja – Markieren und drücken Sie die mittlere Schaltfläche, um eine Änderung anzunehmen und zum vorhergehenden Bildschirm zurückzukehren.
• KVM-Zuordnung – Enthält die Optionen, den Servern den KVM zuzuordnen bzw. die Zuordnung aufzuheben. • DVD-Zuordnung – Diese Option wird auf dem Bildschirm Hauptmenü nur angezeigt, wenn Sie ein DVD-Laufwerk installiert haben. • Gehäuse – Zeigt Statusinformationen für das Gehäuse an. • IP-Zusammenfassung – Zeigt Informationen über CMC-IPv4, CMC-IPv6, iDRAC-IPv4 und iDRAC 4IPv6 an.
Führen Sie mit den Schaltflächen Nach oben und Nach unten einen Bildlauf in der Liste durch. Mit der Linkspfeil- und Rechtspfeil-Schaltfläche können Sie in ausgewählten Meldungen, die nicht auf den Bildschirm passen, einen Bildlauf ausführen. Wählen Sie mit den Schaltflächen Nach oben und Nach unten das Zurück-Symbol aus, und drücken Sie die mittlere Schaltfläche, um zum Gehäuse-Menü zurückzuwechseln.
1. Markieren Sie mit den Pfeiltasten „Nach oben“ und „Nach unten“ den Bildschirm, den Sie als Standardeinstellung festlegen möchten. 2. Drücken Sie die mittlere Schaltfläche. Das Symbol Annehmen ist hervorgehoben. 3. Drücken Sie erneut die mittlere Schaltfläche, um die Änderung zu bestätigen. Der Standardbildschirm wird angezeigt. Diagnose Mit dem LCD-Bedienfeld können Sie Probleme mit Servern oder Modulen im Gehäuse analysieren.
Tabelle 33. CMC-Status Element Beschreibung Name/Standort Beispiel: CMC1, CMC2 Keine Fehler Bei keinem Fehler wird „Keine Fehler“ angezeigt; ansonsten werden Fehlermeldungen aufgelistet, in denen die kritischen Fehler zuerst aufgelistet werden, gefolgt von den Warnungen. Firmware-Version Wird nur auf einem aktiven CMC angezeigt. Zeigt für den Standby-CMC Standby an. IP4 Zeigt den aktuellen IPv4-Aktivierungsstatus nur auf einem aktiven CMC an.
Tabelle 35. Lüfterstatus Element Beschreibung Name/Standort. Beispiel: Lüfter1, Lüfter2, usw. Fehlermeldungen Bei keinem Fehler wird „Keine Fehler“ angezeigt; ansonsten werden Fehlermeldungen aufgelistet, in denen die kritischen Fehler zuerst aufgelistet werden, gefolgt von den Warnungen. RPM Aktuelle Lüftergeschwindigkeit in U/Min. Tabelle 36. Netzteileinheitstatus Element Beschreibung Name/Standort. Beispiel: Netzteileinheit1, Netzteileinheit2, usw.
Element Beschreibung Zugeordnet Zeigt eine Liste der Server an, die einem KVM zugeordnet sind, falls vorhanden. Steckplatz Gibt an, welchem Serversteckplatz das KVM zugeordnet wurde. Mögliche Werte sind Steckplatz <01 bis 04>. Nicht zugeordnet Wird angezeigt, wenn das KVM-Modul keinem Server zugeordnet ist. Tabelle 39. DVD-Zuordnungsstatus Element Beschreibung Server Zeigt eine Liste der Server an, denen das DVD zugeordnet werden kann.
Element Beschreibung Firmware-Version SPERC-Version Hersteller Name des Herstellers Zustand Offline, Online oder Standby – Zeigt den Stromstatus eines SPERC an. Tabelle 42. PCIe-Kartenstatus Element Beschreibung PCIe-Karte Zeigt den Namen der PCIe-Karte im Format „PCIe-Karte “ an, wobei „n“ für die PCIe-Kartennummer steht. Beispiel: PCIe-Karte 1, PCIe-Karte 2 usw.
Tabelle 44. Serverstatus Element Beschreibung Name/Standort Beispiel: Server 1, Server 2 usw. Keine Fehler Bei keinem Fehler wird „Keine Fehler“ angezeigt; ansonsten werden Fehlermeldungen aufgelistet, in denen die kritischen Fehler zuerst aufgelistet werden, gefolgt von den Warnungen. Weitere Informationen finden Sie unter „LCD-Fehlermeldungen“. Steckplatzname Gehäuse-Steckplatzname. Zum Beispiel SLOT-01.
Die Informationen in der Tabelle werden dynamisch aktualisiert. Wenn der Server diese Funktion nicht unterstützt, erscheinen die folgenden Informationen nicht, andernfalls lauten die ServerAdministratoroptionen wie folgt: • Option „Keine“ = Es müssen keine Zeichenketten auf dem LCD angezeigt werden. • Option „Standard“ = Keine Auswirkung. • Option „Benutzerdefiniert“ = Ermöglicht Ihnen die Eingabe eines Zeichenkettennamens für den Server.
Häufig gestellte Fragen 19 In diesem Abschnitt werden häufig gestellte Fragen zu den folgenden Themen aufgelistet: • • • • RACADM Remote-System verwalten und wiederherstellen Active Directory FlexAddress und FlexAddressPlus • EAM RACADM Nach dem Ausführen eines CMC-Resets (mithilfe des RACADM-Unterbefehls racreset), wenn ein Befehl eingegeben wird, wird die folgende Meldung angezeigt: racadm Transport: ERROR: (RC=-1) Was bedeutet diese Meldung? Ein anderer Befehl muss nur dann ausgegeben
Eine Fehlermeldung Not Found wird beim Verwenden der Befehle $ logout und $ quit angezeigt. Remote-System verwalten und wiederherstellen Warum sind die Remote-RACADM- und webbasierten Dienste nach einer Eigenschaftsänderung nicht verfügbar? Es kann etwa eine Minute dauern, bis die Remote-RACADM-Dienste und die Webschnittstelle nach einem Reset des CMC-Webservers wieder verfügbar sind.
Um die Erzeugung von SNMP-Authentifizierungs-Traps zu verhindern, geben Sie Community-Namen ein, die vom Agenten akzeptiert werden. Da der CMC nur einen Community-Namen zulässt, geben Sie den gleichen Get- und Set-Community-Namen für das IT Assistant-Ermittlungs-Setup ein. Wenn ich auf die CMC-Schnittstelle zugreife, erhalte ich eine Sicherheitswarnung, die besagt, dass der Host-Name des SSL-Zertifikats nicht mit dem Host-Namen des CMC übereinstimmt.
Können diese Dell-erweiterten Objekte (Dell-Zuordnungsobjekt, Dell RAC-Gerät und DellBerechtigungsobjekt) in verschiedenen Domänen sein? Das Zuordnungsobjekt und das Berechtigungsobjekt müssen sich in derselben Domäne befinden. Beim Dell-erweiterten Active Directory-Benutzer- und -Computer-Snap-In können Sie diese zwei Objekte nur in derselben Domäne erstellen. Andere Objekte können sich in verschiedenen Domänen befinden. Gibt es Beschränkungen der Domänen-Controller SSL-Konfiguration? Ja.
Es findet keine Aktivierung oder Änderung der Karte statt. Die Karte wird vom CMC ignoriert. In dieser Situation gibt der Befehl $racadm featurecard -s folgende Meldung zurück: Keine Funktionskarte eingesetzt.
Das Servermodul muss ausgeschaltet werden, bevor es mit FlexAddress verwendet werden kann. Nachdem die Server-BIOS-Aktualisierung abgeschlossen wurde, erhält das Servermodul solange keine gehäuseseitigen Adressen, bis der Server aus- und wieder eingeschaltet wurde.