Users Guide
Table Of Contents
- 适用于 Dell EMC PowerEdge VRTX 的 Dell Chassis Management Controller 3.3 版 用户指南
- 概览
- 安装和设置 CMC
- 登录 CMC
- 更新固件
- 查看机箱信息和监测机箱与组件运行状况
- 配置 CMC
- 配置服务器
- 配置插槽名称
- 配置 iDRAC 网络设置
- 配置 iDRAC 虚拟 LAN 标签设置
- 设置第一引导设备
- 配置服务器 FlexAddress
- 配置远程文件共享
- 使用服务器配置复制功能配置配置文件设置
- 配置 CMC 以发送警报
- 配置用户帐户和权限
- 配置 CMC 进行单点登录或智能卡登录
- 配置 CMC 以使用命令行控制台
- 使用 FlexAddress 和 FlexAdress Plus
- 管理结构
- 管理和监测电源
- 管理机箱存储
- 查看存储组件的状态
- 查看存储拓扑
- 使用 CMC Web 界面查看 SPERC 的容错故障排除信息
- 使用 CMC Web 界面向插槽分配虚拟适配器
- 存储控制器中的容错
- 安全密钥不匹配
- 使用 CMC Web 界面查看控制器属性
- 使用 RACADM 查看控制器属性
- 导入或清除外部配置
- 配置存储控制器设置
- Shared PERC 控制器
- 使用 CMC Web 界面启用或禁用 RAID 控制器
- 使用 RACADM 启用或禁用 RAID 控制器
- 使用 RACADM 启用或禁用外部 RAID 控制器的容错功能
- 使用 CMC Web 界面查看物理磁盘属性
- 使用 RACADM 查看物理磁盘驱动器属性
- 识别物理磁盘和虚拟磁盘
- 使用 CMC Web 界面分配全局热备用
- 使用 RACADM 分配全局热备用
- 恢复物理磁盘
- 使用 CMC Web 界面查看虚拟磁盘属性
- 使用 RACADM 查看虚拟磁盘属性
- 使用 CMC Web 界面创建虚拟磁盘
- 管理加密密钥
- 加密虚拟磁盘
- 解锁外部配置
- 加密擦除
- 为虚拟磁盘应用虚拟适配器访问策略
- 使用 CMC Web 界面修改虚拟磁盘属性
- 机柜管理模块
- 使用 CMC Web 界面查看机柜属性
- 管理 PCIe 插槽
- 故障排除和恢复
- 使用 LCD 面板界面
- 常见问题
you # do not have networking) # 3 - Full multiuser mode # 4 - unused # 5 - X11 # 6 - reboot
(Do NOT set initdefault to this) # id:3:initdefault: # System initialization.
si::sysinit:/etc/rc.d/rc.sysinit l0:0:wait:/etc/rc.d/rc 0 l1:1:wait:/etc/rc.d/rc 1
l2:2:wait:/etc/rc.d/rc 2 l3:3:wait:/etc/rc.d/rc 3 l4:4:wait:/etc/rc.d/rc 4 l5:5:wait:/etc/
rc.d/rc 5 l6:6:wait:/etc/rc.d/rc 6 # Things to run in every runlevel. ud::once:/sbin/update #
Trap CTRL-ALT-DELETE ca::ctrlaltdel:/sbin/shutdown -t3 -r now # When our UPS tells us power
has failed, assume we have a few # minutes of power left. Schedule a shutdown for 2 minutes
from now. # This does, of course, assume you have power installed and your # UPS is connected
and working correctly. pf::powerfail:/sbin/shutdown -f -h +2 "Power Failure; System Shutting
Down" # If power was restored before the shutdown kicked in, cancel it. pr:12345:powerokwait:/
sbin/shutdown -c "Power Restored; Shutdown Cancelled" # Run gettys in standard runlevels
co:2345:respawn:/sbin/agetty -h -L 57600 ttyS1 ansi 1:2345:respawn:/sbin/mingetty tty1 2:2345:respawn:/
sbin/mingetty tty2 3:2345:respawn:/sbin/mingetty tty3 4:2345:respawn:/sbin/mingetty tty4
5:2345:respawn:/sbin/mingetty tty5 6:2345:respawn:/sbin/mingetty tty6 # Run xdm in runlevel 5
# xdm is now a separate service x:5:respawn:/etc/X11/prefdm -nodaemon
按照以下说明编辑文件 /etc/securetty:
添加新行,带有 COM2 的串行 tty 名称:
ttyS1
以下示例显示带有新增行的示例文件。
vc/1 vc/2 vc/3 vc/4 vc/5 vc/6 vc/7 vc/8 vc/9 vc/10 vc/11 tty1 tty2 tty3 tty4 tty5 tty6 tty7
tty8 tty9 tty10 tty11 ttyS1
134 配置 CMC 以使用命令行控制台