RACADM Command Line Reference Guide for iDRAC7 1.00.00 and CMC 4.
Notes, Cautions, and Warnings NOTE: A NOTE indicates important information that helps you make better use of your computer. CAUTION: A CAUTION indicates either potential damage to hardware or loss of data and tells you how to avoid the problem. WARNING: A WARNING indicates a potential for property damage, personal injury, or death. © 2012 Dell Inc.
Contents Notes, Cautions, and Warnings...................................................................................................2 1 Introduction................................................................................................................................17 Installing Racadm...................................................................................................................................................17 Supported RACADM Interfaces..................................
getfanreqinfo..........................................................................................................................................................46 getioinfo..................................................................................................................................................................48 getkvminfo..............................................................................................................................................................
setractime...............................................................................................................................................................90 setslotname............................................................................................................................................................92 setsysinfo................................................................................................................................................................
cfgDNSServer1 (Read/Write).........................................................................................................................117 cfgDNSServer2 (Read/Write).........................................................................................................................117 cfgNicEnable (Read/Write)............................................................................................................................117 cfgNicIpAddress (Read/Write).............................
cfgSsnMgtConsRedirMaxSessions (Read/Write)..........................................................................................129 cfgSsnMgtWebserverTimeout (Read/Write).................................................................................................129 cfgSsnMgtSshIdleTimeout (Read/Write).......................................................................................................129 cfgSsnMgtTelnetIdleTimeout (Read/Write).......................................................
cfgRacTuneDaylightOffset (Read Only)..........................................................................................................140 cfgRacTuneTimezoneOffset (Read Only).......................................................................................................141 cfgRacTuneLocalServerVideo (Read/Write)..................................................................................................141 cfgRacTuneLocalConfigDisable (Read/Write).........................................
cfgADSCLEnable............................................................................................................................................152 cfgADSSOEnable (Read/Write)......................................................................................................................152 cfgADDomainController.................................................................................................................................153 cfgADDomainController1 (Read/Write)................
cfgLocationAisle (Read/Write).......................................................................................................................162 cfgLocationRack (Read/Write).......................................................................................................................163 cfgLocationRackslot (Read/Write).................................................................................................................163 cfgLocationDevicesize (Read Only)...........................
cfgIpmiSolMinPrivilege (Read/Write)............................................................................................................172 cfgIpmiSolAccumulateInterval (Read/Write).................................................................................................172 cfgIpmiSolSendThreshold (Read/Write)........................................................................................................172 cfgIpmiLan.....................................................................
cfgServerPowerLastHourMinTime (Read Only).............................................................................................180 cfgServerPowerLastHourMaxPower (Read Only).........................................................................................180 cfgServerPowerLastHourMaxTime (Read Only)............................................................................................180 cfgServerPowerLastDayMinPower (Read Only).............................................................
cfgIPv6AutoConfig (Read/Write)....................................................................................................................190 cfgIPv6LinkLocalAddress (Read Only)...........................................................................................................190 cfgIPv6Address2 (Read Only).........................................................................................................................190 cfgIPv6Address3 (Read Only).....................................
cfgIpmiSerial.........................................................................................................................................................198 cfgIpmiSerialBaudRate (Read/Write).............................................................................................................198 cfgIpmiSerialConnectionMode (Read/Write).................................................................................................199 cfgIpmiSerialChanPrivLimit (Read/Write)...............
cfgRacSecurity.....................................................................................................................................................208 cfgRacSecCsrCommonName (Read/Write)...................................................................................................208 cfgRacSecCsrOrganizationName (Read/Write).............................................................................................208 cfgRacSecCsrOrganizationUnit (Read/Write)............................
System.Power.EnergyConsumption.StarttimeStamp.....................................................................................218 System.Power.PCIeAllocation (Read/Write)..................................................................................................218 System.Power.Supply...........................................................................................................................................218 System.Power.Supply.[i].MaxInputPower (Read Only).........................
Introduction 1 This document provides information about the RACADM subcommands, supported RACADM interfaces, and property database groups and object definitions for the following: • iDRAC Enterprise or Express for Blade Servers • iDRAC Enterprise or Express on Rack and Tower Servers • Dell Chassis System (CMC) Installing Racadm For information on installing and unistalling RACADM, see the Dell OpenManage Server Administrator Installation Guide at support.dell.com/manuals.
Example racadm getconfig -g idracinfo racadm getsysinfo SSH or Telnet RACADM racadm getconfig -g [-o ] [-i ] racadm Example racadm getconfig -g idracinfo racadm getsysinfo Remote RACADM racadm -r -u -p getconfig -g [-o ] [-i ] racadm -r -u -p Example racadm -r -u -p getconfig -g idracinfo racadm -r -u -p getsysinfo RACADM Command Options Table 1‑1 lists the options for the RACADM command.
Option Description -o objectname Specifies the object name if applicable. The following table provides the supported RACADM interfaces for iDRAC Enterprise and iDRAC Express. iDRAC Type Local RACADM SSH/Telnet RACADM Remote RACADM iDRAC Enterprise Yes Yes Yes iDRAC Express Yes Yes Yes CMC No Yes Yes NOTE: Multiple instances of remote RACADM can be executed on a management station, while only one instance of local RACADM can be executed on a managed node.
Subcomma nd iDRAC on Blade Servers iDRAC on Rack and Tower Servers CMC featurecard No No No No No No Yes Yes fwupdate Yes Yes Yes Yes Yes Yes Yes Yes get Yes Yes Yes Yes Yes Yes No No getassettag No No No No No No Yes Yes getchassisn No ame No No No No No Yes Yes getconfig Yes Yes Yes Yes Yes Yes Yes Yes getdcinfo No No No No No No Yes Yes getfanreqinf No o No No No No No Yes Yes getflexaddr No No No No No No Yes Yes getioinfo
Subcomma nd iDRAC on Blade Servers iDRAC on Rack and Tower Servers CMC getuscversi Yes on Yes Yes Yes Yes Yes No No "help" and Yes "help Yes Yes Yes Yes Yes Yes Yes hwinventor y Yes Yes Yes Yes Yes Yes No No ifconfig Yes Yes Yes Yes Yes Yes Yes Yes krbkeytabu pload Yes Yes Yes Yes Yes Yes No Yes lclog Yes Yes Yes Yes Yes Yes No No license Yes Yes Yes Yes Yes Yes No No netstat Yes Yes Yes Yes Yes Yes Yes Yes nicstatistics
Subcomma nd iDRAC on Blade Servers sslcertdow nload No Yes sslcertuplo ad No iDRAC on Rack and Tower Servers CMC Yes No Yes Yes No Yes Yes Yes No Yes Yes No Yes sslcertview Yes Yes Yes Yes Yes Yes Yes Yes sslcsrgen Yes Yes Yes Yes Yes Yes Yes Yes sslkeyuploa No d Yes Yes No Yes Yes No No sslresetcfg Yes Yes Yes Yes Yes Yes Yes Yes testemail Yes Yes Yes Yes Yes Yes Yes Yes testfeature No No No No No No Yes Yes testtrap Yes Yes Yes
• The Dell OpenManage Server Administrator’s User’s Guide provides information about installing and using Dell OpenManage Server Administrator. • The Dell Update Packages User's Guide provides information about obtaining and using Dell Update Packages as part of your system update strategy. • The Glossary provides information about the terms used in this document.
RACADM Subcommand Details 2 This section provides detailed descriptions of the RACADM subcommands including the syntax and valid entries.
• A single quote cannot be used even with a backslash escaped. NOTE: An empty string may be specified as either "" (using double quotes) or '' (using single quotes). "?"and "?" Description Displays all the subcommands you can use with the RACADM command and a one-line description of each subcommand. ? followed by displays the syntax for the specified command. To use this subcommand, you must have CMC Login User privilege.
-d -c -A -4 -6 : : : : : show CMC information show chassis information do not show headers or labels show CMC IPv4 information show CMC IPv6 information help and help subcommand Description Synopsis Input Output Lists all the subcommands available to use with RACADM and provides a short description for each. You may also type a subcommand, group, object, or FQDD alias after help, to get the syntax for the specified keyword.
Output IP Address HW Type Flags HW Address Mask Device 192.168.1.1 0x1 0x2 00:00:0C:07:AC:0F * eth0 chassisaction Description Executes a power action on the chassis, iKVM, or a server. To use this subcommand, you must have Chassis Control Administrator privilege Synopsis racadm chassisaction [-m ] Input • -m — Module on which you want to carry out the action. Values are: — chassis - this is the default value if -m is not specified.
Input None Output None Example None closessn Description Closes a communication session on the device. Use getssninfo to view a list of sessions that can be closed using this command. To use this subcommand, you must have Administrator permission. Synopsis Input • • • racadm closessn –i racadm closessn -a racadm closessn -u • -i — The session ID of the session to close, which can be retrieved using racadm getssninfo subcommand.
cmcchangeover Description Changes the state of the CMC from active to standby, or vice versa, in a redundant CMC configuration. This subcommand is useful for remote debugging or testing purposes. To use this subcommand, you must have Administrator privilege. NOTE: This command is valid only in redundant CMC environments. For more information, see the "Understanding the Redundant CMC Environment" section of the Dell Chassis System User Guide.
• Output -c — The -c, or check option, is used with the config subcommand and allows the user to parse the .cfg file to locate syntax errors. If errors are found, the line number and a short description of what is incorrect are displayed. Write permission does not apply to iDRAC. This option is a check only. This subcommand generates error output for any of the following reasons: • • Invalid syntax, group name, object name, index, or other invalid database members. RACADM CLI failures.
• Another critical condition occurs on iDRAC. In this case, the coredump information is relative to the last critical error that occurred. This option is applicable only for iDRAC. To use this subcommand, you must have Execute Debug Commands permission See the coredumpdelete subcommand for more information about clearing the coredump. Synopsis racadm coredump Input None Output None Example • • racadm coredump No Core Dump Data is currently available.
deploy Description Configures the static IP address, subnet mask, gateway, and password for the root user on iDRAC for the specified server. To use this subcommand, you must have Server Administrator privilege. NOTE: You can also use setniccfg to configure static IP address, subnet mask, and gateway, as well as DHCP, speed, and duplex properties.
Example • • • racadm deploy -m server-8 -s 192.168.0.20 255.255.255.0 192.168.0.1 The server was deployed successfully. The deploy command generates an error when used on the extension slot of a multi-slot server. racadm deploy -m server-9 192.168.0.11 255.255.255.0 192.168.0.1 ERROR: Server in slot 9 is an extension of the server in slot 1. racadm deploy -m server-7 -u root -p calvin -s -6 ::/64 :: 10 feature Description Displays all active chassis features.
featurecard Description Verifies proper SD card installation and displays the SD card status. To use this subcommand, you must have Chassis Configuration Administrator privilege. Synopsis racadm featurecard -s Input -s — Lists active SD card features and SD card status. Output • • • • • Example No feature card inserted — Action: Check the CMC to verify that the SD card was properly inserted.
fwupdate Description Allows you to update the firmware on the iKVM, active CMC, standby CMC, server iDRACs, or an IOM infrastructure device. You can: • • • • • Check the firmware update process status. Update iDRAC or CMC firmware from a FTP or a TFTP server by providing an IP address and optional path. Update iDRAC or CMC firmware from the local file system using Local and Remote RACADM. Rollback to the standby firmware.
For Remote RACADM: racadm fwupdate -p -u -d NOTE: iDRAC7 targets are not supported from CMC. Use the CMC GUI to update iDRAC7 targets from CMC. When using FTP, if you provide the full path to the image file on the CLI, then the CMC uses that path to locate that file on the host. If you do not provide a full path, then the CMC searches the home directory of the specified user for the file if the host system is running Linux or another variant of UNIX.
• This option is applicable only for CMC. -m — Specifies the module or device to be updated. is one of the following values: — cmc-active (default) — cmc-standby — kvm — server-nx where n=1-8 ; x = a,b,c,d — server-generation where generation = iDRAC or iDRAC6 only. — iominf-n where n = 1–6 NOTE: iDRAC7 targets are not supported from CMC. Use the CMC GUI to update iDRAC7 targets from CMC. CMC version 3.
• Download firmware update file from a specified location on the TFTP server at a specific IP address. racadm fwupdate -g -u -a 143.166.154.143 -d After the image file is downloaded from the TFTP server, the update process begins. When completed, iDRAC is reset. • Read the current status of the firmware update. racadm fwupdate -s NOTE: Firmware update from local racadm (using -p -u -d options) is not supported on linux OS. NOTE: For CMC, these commands specifically apply to an active-CMC update.
• • • • • • Examples — Specifies the group containing the object that is to be read.
getconfig Description Retrieves iDRAC configuration parameters individually, or all iDRAC configuration groups may be retrieved and saved to a file. Synopsis racadm getconfig -f racadm getconfig -g [-i ] racadm getconfig -u racadm getconfig -h racadm getconfig -g -o [-i index] Input • • • • • • • Output -f — The -f option directs getconfig to write the entire iDRAC configuration to a configuration file.
If errors are not encountered, this subcommand displays the contents of the specified configuration. Example • • racadm getconfig -g cfgLanNetworking Displays all of the configuration properties (objects) that are contained in the group cfgLanNetworking. racadm getconfig -f myrac.cfg Saves all group configuration objects from iDRAC to myrac.cfg. • racadm getconfig -h Displays a list of the available configuration groups on iDRAC in an alphabetical order.
switch-3 Gigabit Ethernet OK Master switch-4 None N/A N/A switch-5 Gigabit Ethernet OK Member switch-6 None N/A N/A server-1 Present None N/A None N/A server-2 Not Present None N/A None N/A server-3 Not Present None N/A None N/A server-4 Present None N/A Gigabit Ethernet OK server-5 Not Present None N/A None N/A server-6 Not Present None N/A None N/A server-7 Not Present None N/A
server-6 Not Present None None server-7 Not Present None None server-8 Present LPe1105-M4 None server-9 Extension(1) None None server-10 Not Present None None server-11 Not Present None None server-12 Not Present None None server-13 Not Present None None server-14 Not Present None None server-15 Not Present None None server-16 Not Present None None getflexaddr Description Displays enabled/disabled status for the entire chassis.
2 Enabled Present 3 Enabled Not Present 4 Enabled Not Present 5 Enabled Present 6 Enabled Not Present 7 Enabled Not Present 8 Enabled Not Present 9 Enabled Not Present 10 Enabled Extension(2) 11 Enabled Not Present 12 Enabled Not Present 13 Enabled Extension(5) 14 Enabled Not Present 15 Enabled Not Present 16 Enabled Not Present idrac System Disabled Display the current flex address setting for slot 1.
slot1-B2 Gigabit Ethernet 00:1D:09:71:B3:62 00:1E:C9:FF:E3:27(a ctive) iSCSI 00:1D:09:71:B3:63 00:1E:C9:FF:E3:28(a ctive) slot1-C1 Fiber Channel 4 10:00:00:00:C9:63:5 1:0E 20:01:00:1E:C9:FF:E 3:29(active) slot1-C2 Fiber Channel 4 10:00:00:00:C9:63:5 1:0D 20:02:00:1E:C9:FF:E 3:29(active) getfanreqinfo Description Displays fan speed request for Servers and Switches in percent (%). To use this subcommand, you must have CMC Login User privilege. This subcommand is not applicable for iDRAC.
8 SLOT-08 PowerEdgeM71 ON 0 Present 44 9 SLOT-09 N/A N/A Not Present N/A 10 SLOT-10 N/A Extension(2) N/A N/A 11 SLOT-11 N/A Extension(3) N/A N/A 12 SLOT-12 N/A N/A Not Present N/A 13 SLOT-13 N/A N/A Not Present N/A 14 SLOT-14 PowerEdgeM60 ON 0 Present 33 15 SLOT-15 N/A N/A Not Present N/A 16 SLOT-16 N/A Extension(8) N/A N/A Switch Module Fan Request Table 1 SLOT-01 PowerEdgeM60
13 SLOT-13 N/A 14 SLOT-14 15 16 N/A Not Present N/A PowerEdgeM60 ON 0 Present 33 SLOT-15 N/A N/A Not Present N/A SLOT-16 N/A Extension(8) N/A N/A Switch Module Fan Request Table Switch-1 Dell Ethernet Pass-Through Gigabit Ethernet Present 30 Switch-2 Dell PowerConnect M6220 Gigabit Ethernet Present 30 Switch-3 N/A None Not Present N/A Switch-4 N/A None Not Present N/A Switch-5 N/A None Not Present N/A Switch
switch-4 N/A None Not Present N/A N/A N/A switch-5 N/A None Not Present N/A N/A N/A switch-6 N/A None Not Present N/A N/A N/A getkvminfo Description Displays iKVM module information. To use this subcommand, you must have CMC Login User privilege. Synopsis racadm getkvminfo Example racadm getkvminfo KVM Present Avocent iKVM Switch 00.05.00.
• racadm getled -m server-9 server-9 Extension(1) For iDRAC: racadm getled LED is blinking getmacaddress Description Synopsis Input Displays the MAC/WWN addresses for all modules or for a specified module. To use this subcommand, you must have CMC Login User privilege. • • racadm getmacaddress [-m ] [-t iscsi] [-x] racadm getmacaddress [-a] • -m — Specifies the module whose MAC address you want to view.
server-1 Present 00:11:43:FD:B7: 00:11:43:FD:B7: 00:11:43:FD:B7: 2A 2A 2B 00:11:43:FD:B7: 00:11:43:FD:B7: 2C 2D racadm getmacaddress CMC Present N/A 00:1E:4F:1F:3C: N/A 58 Server-1 Present 00:1E:4F:2A:AF: 00:1E:4F: 7B 2A:D3:97 00:1E:4F: 2A:D3:99 Server-2 Present 00:22:19:D2:1E: N/A 84 N/A Server-3 Not Present N/A N/A N/A Server-4 P
Switch-1 Present N/A 00:00:00:00:00: N/A 00 Switch-2 Present N/A 00:00:00:00:00: N/A 00 Switch-3 Present N/A 00:00:00:00:00: N/A 00 Switch-4 Present N/A 00:00:00:00:00: N/A 00 Switch-5 Present N/A 00:05:1E:08:EB: N/A 0B Switch-6 Not Present N/A N/A N/A Display Ethernet and iSCSI MACS of all LOMs/mezzanine cards.
Server-4-A Gigabit Ethernet Present 00:18:8B:FF: 00:18:8B:FF: 00:18:8B:FF: 45:2A AA:02 AA:04 iSCSI Present 00:18:8B:FF: 00:18:8B:FF: AA:03 AA:05 Gigabit Ethernet Not Present Not Installed Not Installed iSCSI Present Not Installed Not Installed Server-4-C Fibre Channel 4 Present Not Installed Not Installed Server-5-A Gigabit Ethernet Present 00:19:B9:FF: 00:19:B9:FF: 00:19:B9:FF: FE:E2 FC:0C FC:0E iSCSI Present 00:19:B9:FF: 00:19:B9:FF: FC:0D FC:0F Gigabit Ethernet Present Not In
Server-10 N/A Not Present N/A N/A N/A Server-11 N/A Not Present N/A N/A N/A Server-12 N/A Not Present N/A N/A N/A Server-13-A Gigabit Ethernet Present 00:18:8B:FF: 00:18:8B:FF: 00:18:8B:FF: 45:26 A9:F2 A9:F4 iSCSI Present 00:18:8B:FF: 00:18:8B:FF: A9:F3 A9:F5 Gigabit Ethernet Present 00:1D: 09:71:E0:78 00:1D: 09:71:E0:7A iSCSI Present 00:1D: 09:71:E0:79 00:1D: 09:71:E0:7B Server-13-C Fibre Channel 4 Present 21:00:00:1B: 21:01:00:1B: 32:0E:EF:30 32:2E:EF:30 Server-14-A G
Switch-4 None Present N/A 00:00:00:00: N/A 00:00 Switch-5 None Present N/A 00:05:1E: 08:EB:0B N/A Switch-6 N/A Not Present N/A N/A N/A getmodinfo Description Displays configuration and status information for all modules or a specified module (server, switch, CMC, fan unit, power supply unit, KVM, or I2C cable) in the chassis. For CMC (only) a power state of "Primary" denotes Active CMC. To use this subcommand, you must have CMC Login User privilege.
PS-3 PS-4 PS-5 PS-6 CMC-1 CMC-2 Switch-1 Switch-2 Switch-3 Switch-4 Switch-5 Switch-6 Server-1 Server-2 Server-3 Server-4 Server-5 Server-6 Server-7 Server-8 Server-9 Server-10 Server-11 Server-12 Server-13 Server-14 Server-15 Server-16 KVM IO-Cable FPC-Cable Present Not Present Not Present Not Present Present Not Present Not Present Not Present Not Present Not Present Not Present Not Present Not Present Present Present Present Present Present Present Not Present Not Present Extension(2) Not Present Presen
Example racadm getniccfg racadm getniccfg –m Output The getniccfg subcommand displays an appropriate error message if the operation is not successful. Otherwise, on success, the output is displayed in the following format: IPv4 settings: NIC Enabled = 1 IPv4 Enabled = 1 DHCP Enabled = 1 IP Address = 10.35.0.64 Subnet Mask = 255.255.255.0 Gateway = 10.35.0.
NOTE: IPv6 information is displayed only if IPv6 is enabled in iDRAC. NOTE: LOM Status is displayed only for iDRAC on Rack and Tower servers and is not displayed for iDRAC Enterprise on Blade servers. getpbinfo Description Displays power budget status information. To use this subcommand, you must have CMC Login User privilege.
4 5 6 7 8 9 10 11 12 13 14 15 16 SLOT-04 SLOT-05 SLOT-06 SLOT-07 SLOT-08 SLOT-09 SLOT-10 SLOT-11 SLOT-12 SLOT-13 SLOT-14 SLOT-15 SLOT-16 ON ON ON ON N/A N/A Extension(2) N/A ON N/A ON ON ON 155 180 180 170 N/A N/A N/A N/A 125 N/A 342 140 125 W W W W W W W W 5 5 5 5 5 5 5 5 5 5 5 5 5 PowerEdgeM600 N/A N/A N/A N/A PowerEdgeM600 N/A N/A N/A getpminfo Description Displays power management status information. To use this subcommand, you must have CMC Login User privilege.
Overall Power Health = OK Redundancy = No [System Power Policy Configuration] System Input Power Cap = 7928 W (7928 BTU/hr | 10%) Surplus for Peak Performance = 7000 W (6130 BTU/hr) Redundancy Policy = None Dynamic PSU Engagement Enabled = No [Power Budgeting] System Input Max Power Capacity = 0 W Input Redundancy Reserve = 0 W Input Power Allocated to Servers = 0 W Input Power Allocated to Chassis Infrastructure = 51W Total Input Power Available for Allocation = 0 W Standby Input Power Capacity = 0 W getr
Source: login[433] Description: root login from 143.166.157.103 NOTE: For iDRAC Enterprise on Blade Servers, iDRAC Log entries for SystemBoot displayed using the local racadm command racadm getraclog may not be correctly formatted. For example, some extra characters may be displayed in the Description field, or the Source field may be empty. Example racadm getraclog -s 10 -c 2 getractime Description Synopsis Input Displays the current iDRAC time.
getsel Description Synopsis Displays all sensor event log entries in the DRAC. • • racadm getsel -i [-A] racadm getsel [-s ] [-c ] [-A] [-o] [-E] [-R] [--more] If no arguments are specified, the entire log is displayed. Input • • • • • • • • -A — Specifies output with no display headers or labels. -c — Provides the number of records to be displayed. -o — Displays each entry in the SEL in a single line. -s — Specifies the starting record used for the display.
Temp 1 Ambient_Temp OK 22 PWR 1 PS-1 Online OK PWR 2 PS-2 Online OK PWR 3 PS-3 Online OK PWR 4 PS-4 Slot Empty PWR 5 PS-5 Failed PWR 6 PS-6 celcius N/A 40 N/A OK Slot Empty N/A Cable 1 IO-Cable OK Cable 2 FPC-Cable OK getslotname Description Displays the name and hostname (if available) of all 16 slots, or of a specified slot (indicated by the slot number) in
8 9 10 11 12 13 14 15 16 SLOT-08 SLOT-09 SLOT-10 SLOT-11 SLOT-12 SLOT-13 SLOT-14 SLOT-15 SLOT-16 racadm getslotname -i 1 Webserver-1 getssninfo Description Displays a list of users that are connected to iDRAC.
Input getsvctag Output Y76TP0G Example racadm getsvctag getsysinfo Description Displays information related to iDRAC, managed system, and watchdog configuration. . NOTE: The local racadm getsysinfo subcommand on Linux displays the PrefixLength on separate lines for IPv6 Address 2 – IPv6 Address 15 and the Link Local Address. NOTE: The Hostname and OS Name fields in the getsysinfo output display accurate information only if Dell OpenManage Server Administrator is installed on the managed system.
Current DNS Server 2 DNS Servers from DHCP = 163.244.180.
"Microsoft Windows 2000 version 5.0, Build Number 2195, Service Pack 2" "ON" • racadm getsysinfo -w -s System Information: System Model System Revision System BIOS Version BMC Firmware Version Service Tag Host Name OS Name Power Status = = = = = = = = Watchdog Information: Recovery Action Present countdown value Initial countdown value = None = 0 seconds = 0 seconds PowerEdge 2900 I 0.2.3 0.
This option is applicable only for iDRAC. Synopsis racadm getuscversion Example $ racadm getuscversion 1.2.3.4 getversion Description Synopsis Input Displays the current software version, model and generation information, and whether or not the target device can be updated. To use this subcommand, you must have CMC Login User privilege.
server-2 1.50 PowerEdgeM600 iDRAC Y server-3 2.10 PowerEdgeM610 iDRAC Y server-4 1.50 PowerEdgeM605 iDRAC Y cmc-1 2.10.X06.200906 080825 Y racadm getversion -c server-1 PowerEdgeM600 server-2 PowerEdgeM805 server-5 1.0.0 PowerEdgeM710 server-1 2.0.0 PowerEdgeM605 server-2 1.1.0 PowerEdgeM805 server-5 1.
Broadcom 5709 Emb(nic-1) 5.2.0 2011-02-02 PERC6 EMB (raid-2) 07.01.34.00 2011-02-02 BIOS 0.1.7 Rollback BIOS 1.2.1 Reinstall iDRAC 3.20 Reinstall PERC6 Emb (raid-2) 07.01.33.00 Rollback PERC6 Emb (raid-2) 07.01.33.00 Reinstall racadm getversion -l -m server-1 -f bios server-1 BIOS 1.2.
Subdevice ID: Perm ISCSI MAC Address: Slot Type: Data Bus Width: Slot Length: Perm FCoE MAC Address: PCI Bus: PCI Device: PCI Function: Update Time: Sync Time: Product Name: Permanent MAC Address: WWPN: Family Version: Controller BIOS Version: EFI Version: Max Bandwidth: Min Bandwidth: Current Commit Index: FCoE WWNN: Vendor Name: Ports Count: Number PCIE Functions Supported: Number PCIE Functions Enabled: Link Duplex: Link Speed: Auto Negotiation: Transmit Flow Control: Receive Flow Control: Media Type: St
Example $ racadm ifconfig eth0 Link encap:Ethernet 00:1D:09:FF:DA:23 HWaddr inet addr:10.35.155.136 Bcast:10.35.155.255 Mask:255.255.255.0 MULTICAST Metric:1 UP BROADCAST RUNNING MTU:1500 RX packets:2550665 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 1000 (259.9 MiB) (0.0 B) collisions:0 txqueuelen: RX bytes:272532097 TX bytes:0 krbkeytabupload Description Uploads a Kerberos keytab file. To use this subcommand, you must have Configure iDRAC permission.
lclog Description Allows the user to export the lifecycle log history, and view the lifecycle log for a particular device or category. To use this subcommand, you must have Configure iDRAC permission. This subcommand is applicable for iDRAC only. NOTE: On Local RACADM, when you run this command, the data is exposed to RACADM as a USB partition. This may display a pop up. Synopsis Input racadm lclog view -i -a -c -s -b -q
• • • • • • • -d - Specifies the path to the file on the FTP server. -l - Specifies the location of the network share or area on file system where lifecycle log is exported. Two types of network shares are supported: — SMB mounted path: //// — NFS mounted path: :/. -u — Specifies the user name for accessing the FTP Server, or Domain and User Name for accessing network share location.
• Display all the available records from the active Life Cycle Log: racadm lclog view license Description Synopsis Input Manages hardware licenses. This subcommand is applicable for iDRAC only.
NOTE: Only a user with Administrator privileges can use the import, export, delete, and replace commands. You do not need Administrator privileges to use the view command. Examples • View All License Information on System $racadm license view iDRAC.Embedded.1 Status = OK Device = iDRAC.Embedded.
• Export license to a NFS share using transaction ID, in this case transaction 27 : racadm license export -f License.xml -l 192.168.2.140:/licshare -t 27 • Export license to a CIFS share specifying the entitlement ID, in this case abcdxyz : racadm license export -u admin -p passwd -f License.xml -l //192.168.2.140/licshare -e abcdxyz • Export license to a CIFS share specifying the FQDD. While using the -c option and exporting license(s) from a device, more than one license file may be exported.
Examples • Displays the statistics for the NIC FQDD. $racadm nicstatistics • Displays the statistics for the integrated NIC. $ racadm nicstatistics NIC.Integrated.1-1 Total Bytes Received:0 • Total Bytes Transmitted: 0 Total Unicast Bytes Received: 0 Total Multicast Bytes Received: 0 Total Broadcast Bytes Received: 0 Total Unicast Bytes Transmitted: 0 Get the network statistics $ racadm nicstatistics NIC.Slot.5-2-1 : QLogic CNA Gigabit Ethernet-B8:AC:6F:B3:BF:10 NIC.Slot.
Example racadm iping6 10.9.72.254 IPING6 10.9.72.254 (10.9.72.254): 56 data bytes 64 bytes from 10.9.72.254: icmp_seq=0 ttl=121 time=2.9 ms --- 10.9.72.254 ping statistics --1 packets transmitted, 1 packets received, 0 percent packet loss round-trip min/avg/max = 2.9/2.9/2.9 ms racdump Description Provides a single command to get dump, status, and general iDRAC board information.
• • Process information Firmware build information Example Example racadm racdump =============================================================================== General System/RAC Information =============================================================================== CMC Information: CMC Date/Time Active CMC Version Standby CMC Version Last Firmware Update Hardware Version Current IP Address Current IP Gateway Current IP Netmask DHCP Enabled MAC Address Current DNS Server 1 Current DNS Server 2 DNS S
FanSpeed FanSpeed 8 9 Fan-8 Fan-9 Not OK OK 1 4826 rpm rpm 7250 14500 2344 14500 Temp 1 Ambient_Temp OK 21 celcius N/A PWR 1 PWR 2 PWR 3 PWR 4 PWR 5 PWR 6 PS-1 PS-2 PS-3 PS-4 PS-5 PS-6 40 Online OK Online OK Online OK Slot Empty N/A Failed OK Slot Empty N/A racreset Description Issues a reset to iDRAC. The reset event is written into iDRAC log.
racresetcfg Description This subcommand is applicable for iDRAC only. Deletes your current iDRAC configuration and resets iDRAC and serial configuration to the default settings. After reset, the default name and password is root and calvin, respectively, and the IP address is 192.168.0.120. Only for iDRAC Enterprise on Blade servers, it is IP address plus the number of the slot the server inhabits in the chassis.
raid Description Allows you to execute commands to control RAID arrays. To use this subcommand for CMC you must have Chassis Administartor privilege and for iDRAC you must have Configure iDRAC permission. Synopsis racadm raid Example • Monitor Health of Storage root node racadm raid get status Storage Root Node Status : Ok The above command retrieves the controllers keys, (FQDDs.
• Monitor and Inventory all storage enclosures connected to the connector racadm raid get enclosures --refkey The above command displays all enclosure keys connected to the connectors being mentioned as refkeys. racadm raid get enclosures --refkey -o optimized version. The above command displays all enclosure objects for the connector FQDD.
The above command displays all temperature probe keys connected to the enclosures being mentioned as refkeys. racadm raid get tempprobes -refkeys -o The above command is an optimized version and displays all temperature probe objects for the enclosure FQDD.
serveraction Description Enables users to perform power management operations on the host system. To use this subcommand, you must have Execute Server Control Commands permission. Synopsis racadm serveraction Input • • • • -m server-nx where n=1-8 ; x = a,b,c,d -a - Performs action on all servers. Not allowed with the powerstatus action. -f - Force the action. Required for the reseat action. - Specifies the action.
• Server power operation successful Explanation of Support iDRAC Needs to support graceful shutdown The support of address individual blades is expected on the CMC set Description Synopsis Input Output Example Allows the user to set the value of configuration objects on a device. To use this subcommand, you must have Configure privilege. This subcommand is applicable for iDRAC only. • racadm set -f • racadm set [.][.][.] [.
• racadm setassettag 783839–33 The asset tag was changed successfully. setchassisname Description Sets the name of the chassis in the LCD. To use this subcommand, you must have Administrator privilege. Synopsis racadm setchassisname NOTE: Chassisname is a maximum of 64 non-extended ASCII characters. Example racadm setchassisname dellchassis-1 The chassis name was set successfully. setflexaddr Description Enables/disables FlexAddress on a particular slot/fabric.
setled Description Sets the state (blinking or not blinking) of the LED on the specified module. To blink or unblink the chassis, I/O modules or the CMC, you must have Debug Administrator privilege on CMC. To enable the servers to blink or unblink, you must have Server Administrator or Debug Administrator privilege on CMC. To use this subcommand for iDRAC, you must have Configure iDRAC permission.
setniccfg Description Sets the iDRAC IP address. It displays an error message if the requested operation could not be performed, or a success message if the operation is completed successfully. To use this subcommand, you must have Configure iDRAC permission. NOTE: The terms NIC and Ethernet management port may be used interchangeably.
— mm is the month — dd is the day — hh is the hour — mm is the minutes — ss is the seconds — mmmmmm is the number of microseconds — s is a + (plus) sign or a - (minus) sign, which indicates the sign of the offset — off is the offset in minutes NOTE: The off is the offset in minutes from GMT and must be in 15-minute increments. The timezone is represented as an offset from GMT, and the clock does not automatically adjust to daylight savings time (for '-d' option).
setslotname Description Displays the name and hostname (if available) of all 16 slots, or of a specified slot (indicated by the slot number) in the chassis. Optionally, this command can be used to set whether the slot name or hostname is displayed in the CMC User Interface or with the getslotname -i command. If the hostname is not available, the static slot name is used. To use this subcommand, you must have Administrator privilege.
• Example -c — Sets the chassis name or location. racadm setsysinfo -c chassisname "Dell Rack System" The chassis name was set successfully. sshpkauth Description Enables you to upload and manage up to 4 different SSH public keys per user. You can upload a key file or key text, view keys, or delete keys. This command has three mutually exclusive modes— upload, view, and delete that are determined by the options.
• • • • options. must be between 1 to 4 or all on iDRAC. -t - Key text for the SSH Public key. -f - File containing the key text to upload. The -f option is not supported on Telnet/ssh/serial RACADM. -v - View the key text for the index provided. -d - Delete the key for the index provided.
• -f — Specifies the file name of the certificate to be downloaded. Output Returns 0 when successful and a nonzero number when unsuccessful. Example racadm sslcertdownload -t 1 -f c:\cert \cert.txt sslcertupload Description Uploads a custom SSL server or CA certificate for Directory Service from the client to iDRAC. To use this subcommand, you must have Configure iDRAC permission.
• —2 = CA certificate for Directory Service -A — Prevents printing headers/labels. Output racadm sslcertview -t 1 Serial Number 00 Subject Information: Country Code (CC) US State (S) Texas Locality (L) Round Rock Organization (O) Dell Inc. Organizational Unit (OU) Remote Access Group Common Name (CN) iDRAC Default certificate Issuer Information: Country Code (CC) US State (S) Texas Locality (L) Round Rock Organization (O) Dell Inc.
racadm sslcertview -t 1 -A 00 US Texas Round Rock Dell Inc. Remote Access Group iDRAC default certificate US Texas Round Rock Dell Inc. Remote Access Group iDRAC default certificate Jul 8 16:21:56 2005 GMT Jul 7 16:21:56 2010 GMT sslcsrgen Description Generates and downloads a CSR file to the client’s local file system. The CSR can be used for creating a custom SSL certificate that can be used for SSL transactions on iDRAC. To use this subcommand, you must have Configure iDRAC permission.
The sslcsrgen -s subcommand returns one of the following status codes: • • Example CSR was generated successfully. CSR does not exist. racadm sslcsrgen -s or racadm sslcsrgen -g -f c:\csr \csrtest.txt NOTE: Before a CSR can be generated, the CSR fields must be configured in the RACADM cfgRacSecurity group. For example: racadm config -g cfgRacSecurity -o cfgRacSecCsrCommonName MyCompany NOTE: In telnet/ssh console, you can only generate and not download the CSR file.
testemail Description Sends a test e-mail from iDRAC to a specified destination. Prior to executing the test email command, make sure that the SMTP server is configured and the specified index in the RACADM cfgEmailAlertgroup is enabled and configured properly. See cfgEmailAlert for more information. Synopsis racadm testemail -i Input -i — Specifies the index of the e-mail alert to test.
Option Description -f Specifies the feature name. testfeature supports the following features: • • • ad — Tests Active Directory configuration using simple authentication (user name and password) adkrb — Tests Active Directory configuration using Kerberos authentication ldap — Tests LDAP configuration and operation (requires user name and password) -u The user name specified in an appropriate format for the selected authentication method.
• • The last three digits are the user's permissions. testfeature –f adkrb –u user_name@domain_name SUCCESSFUL: User permissions are 80000fff testfeature -f ldap -u harold -p barrel SUCCESSFUL: User permissions are 0x00000fff testfeature -f adkrb Description Tests the Active Directory configuration using Kerberos authentication (single sign-on or Smart Card login). Use the optional -d switch to obtain additional diagnostic information, as needed.
Description Tests LDAP configuration and operation, and reports success as each stage of the authentication process proceeds. On successful completion, this command prints the CMC privileges assumed by the specified . If a failure occurs, the command terminates with an error message that displays the required corrective action. Use the optional -d switch to obtain additional diagnostic information, as needed.
To use this subcommand, you must have Administrator permission. Synopsis racadm traceroute racadm traceroute 192.168.0.1 Input racadm traceroute 192.168.0.1 Output traceroute to 192.168.0.1 (192.168.0.1), 30 hops max, 40 byte packets 1 192.168.0.1 (192.168.0.1) 0.801 ms 0.246 ms 0.253 ms traceroute6 Description Traces the network path of routers that packets take as they are forwarded from your system to a destination IPv6 address.
• • -f - Specifies the file name of the certificate to be uploaded. If the file is not specified, the sslcert file in the current directory is selected. -i - Index number of the user. Valid values 1-16. Output Returns 0 when successful and a nonzero number when unsuccessful. Example racadm usercertupload -t 1 -f c:\cert \cert.txt -i 6 usercertview Description Displays the user certificate or user CA certificate that exists on iDRAC. To use this subcommand, you must have Configure iDRAC permission.
vflashpartition Description Allows you to perform the following: • • • • • • Create an empty partition Create a partition using an image file Format a partition View available partitions Delete existing partitions Get the status of partitions To use this subcommand, you must have Access Virtual Media privilege.
NOTE: When an empty partition is created the default Access type is always Read-Write. • image – Create a partition using an image relative to iDRAC. The following options are valid with the image type: -l – Specifies the remote path relative to iDRAC. The path can be on a mounted drive: SMB path: /// / NFS path: :/ -u – Username for accessing the remote image. -p – Password for accessing the remote image.
• • • To display the format type of the partition: racadm getconfig –g cfgvflashpartition cfgvflashPartitionFormatType –i 1 –o To change a read-only partition to read-write: racadm config –g cfgvflashpartition 1 –i 1 –o cfgvflashPartitionAccessType To attach a partition to the host operating system: racadm config –g cfgvflashpartition cfgvflashPartitionAttachState 1 –i 1 –o vmdisconnect Description Allows a user to disconnect another user's Virtual Media session.
iDRAC and CMC Property Database Group and Object Descriptions 3 The iDRAC and CMC property database contains the configuration information for iDRAC and CMC. Data is organized by associated object, and objects are organized by object group. The IDs for the groups and objects that the property database supports are listed in this section for iDRAC Enterprise on Blade Servers, iDRAC Enterprise or Express on Rack and Tower Servers and CMC.
Subcommand iDRAC on Blade Servers iDRAC on Rack and Tower Servers CMC ifcRacManagedNodeOs Yes Yes No cfgRacSecurity No No Yes cfgRacVirtual Yes Yes No cfgServerInfo No Yes Yes cfgActiveDirectory Yes Yes Yes cfgLDAP Yes Yes Yes cfgLdapRoleGroup Yes Yes Yes cfgStandardSchema Yes Yes Yes cfgChassisPower No No Yes cfgIpmiSol Yes Yes No cfgIpmiLan Yes Yes No cfgIpmiPetIpv6 Yes Yes No cfgIpmiPef Yes Yes No cfgIpmiPet Yes Yes No cfgUserDomain Yes Yes N
idRacInfo This group contains display parameters to provide information about the specifics of iDRAC or CMC being queried. One instance of the group is allowed. For CMC, use this object with the getconfig subcommand. To use this object for CMC, you must have CMC Login User privilege. The following sections provide information about the objects in the idRACInfo group. idRacProductInfo (Read Only) Description A text string that identifies the product. Legal Values A string of up to 63 ASCII characters.
Default for CMC CMC idRacType (Read Only) Description Identifies the remote access controller type as iDRAC.
cfgNicSelection (Read/Write) Description Specifies the current mode of operation for the RAC network interface controller (NIC). The table below describes the supported modes. This object is applicable only for iDRAC on Rack and Tower Servers and not for iDRAC Enterprise on Blade Servers or CMC.
iDRAC displays only the current VLAN settings and you cannot modify the settings from iDRAC. All chassis management traffic, including the CMC and all iDRACs, resides on this external VLAN when enabled. No iDRAC configuration change is required to use this external management network VLAN.
cfgDNSDomainNameFromDHCP (Read/Write) Description Specifies that iDRAC or CMC DNS domain name should be assigned from the network DHCP server. Legal Values Default • • 1 (TRUE) 0 (FALSE) 0 For CMC, this property is used only if cfgNicUseDhcp is set to 1 (true), or if both cfgIPv6Enable and cfgIPv6AutoConfig are set to 1 (true).
Default For iDRAC: idrac- For CMC: cmc- cfgDNSRegisterRac (Read/Write) Description Registers the iDRAC or CMC name on the DNS server. When you set this parameter, the CMC registers its DNS name for its IPv4 and IPv6 addresses with the DNS server. Legal Values Default • • 1 (TRUE) 0 (FALSE) 0 NOTE: For IPv6, only the DHCPv6 address or static address is registered. Example: racadm getconfig -g cfgLanNetworking cfgNicEnable=1 cfgNicIPv4Enable=1 cfgNicIpAddress=192.168.22.
cfgDNSServersFromDHCP (Read/Write) Description Specifies if the DNS server IPv4 addresses should be assigned from the DHCP server on the network. For CMC, this property is used only if cfgNicUseDhcp is set to 1 (true). Legal Values Default • • 1 (TRUE) 0 (FALSE) 0 cfgDNSServer1 (Read/Write) Description Specifies the IPv4 address for DNS server 1. This property is only valid if cfgDNSServersFromDHCP is set to 0 (FALSE).
cfgNicIpAddress (Read/Write) Description Specifies the static IPv4 address to be assigned to the RAC or CMC. NOTE: This parameter is only configurable if the cfgNicUseDhcp parameter is set to 0(FALSE.) Legal Values String representing a valid IPv4 address. For example: 192.168.0.20. Default • • • For iDRAC on Rack and Tower Servers: 192.168.0.120 For iDRAC Enterprise on Blade Servers: 192.168.0.n, where n is 120 plus the server slot number. For CMC: 192.168.0.
cfgNicUseDhcp (Read/Write) Description Specifies whether DHCP is used to assign the iDRAC or CMC IPv4 address. If this property is set to 1 (TRUE), then iDRAC or CMC IPv4 address, subnet mask, and gateway are assigned from the DHCP server on the network. If this property is set to 0 (FALSE), the user can configure the cfgNicIpAddress, cfgNicNetmask, and cfgNicGateway properties.
cfgRhostsFwUpdateIpAddr (Read/Write) Description Specifies the network TFTP server IPv4 or IPv6 address that is used for TFTP iDRAC or CMC firmware update operations. Legal Values A string representing a valid IPv4 or IPv6 address. For example, 192.168.0.61 Default For IPv4, it is 0.0.0.0 cfgRhostsFwUpdatePath (Read/Write) Description Specifies TFTP path where iDRAC or CMC firmware image file exists on the TFTP server. The TFTP path is relative to the TFTP root path on the TFTP server.
This object is applicable only for CMC. Legal Values A string representing a valid NTP server. For example, ntp1.ntp.net. At least one NTP server must be specified and duplicate entries are not allowed. Default Null cfgRhostsNtpServer2 Description Specifies the second of three possible NTP servers. This object is applicable only for CMC. Legal Values A string representing a valid NTP server. For example, ntp2.ntp.net. At least one NTP server must be specified and duplicate entries are not allowed.
cfgRhostsSyslogPort (Read/Write) Description Remote syslog port number to use for writing the RAC and SEL logs to a remote syslog server. For CMC, this setting takes effect only if the cfgRhostsSyslogEnable parameter is set to 1 (enabled). Legal Values 10 — 65535 NOTE: For CMC, the following port numbers are reserved and cannot be used: 21, 68, 69, 123, 161, 546, 801, 4096, 5988, 5989, 6900, 9000, 60106.
cfgRhostsSyslogPowerLoggingEnabled Description Enables or disables power consumption logging to remote syslog servers. This object is applicable only for CMC. NOTE: Remote syslog must be enabled and one or more remote syslog servers must be configured for power consumption to be logged. Legal Values • • Default 1 (enabled) 0 (disabled) 0 cfgRhostsSyslogPowerLoggingInterval Description Specifies the power consumption collection/logging interval. This object is applicable only for CMC.
NOTE: In the current CMC firmware version, the objects cfgUserAdminEnable and cfgUserAdminPrivilege are interrelated; changing the value of one property causes the value of the other property to change. For example, if a user does not have login privilege, the user is disabled by default. When you enable the user by changing the value of UserAdminEnable to 1, the right most digit of the UserAdminPrivilege also becomes 1.
Default 0x00000000 Example racadm getconfig -g cfgUserAdmin -i 1 # cfgUserAdminIndex=1 cfgUserAdminEnable=1 cfgUserAdminUserName=root # cfgUserAdminPassword=******** (Write-Only) cfgUserAdminPrivilege=0x00000fff The following table lists the bit masks for user priveleges.
The user may login to iDRAC or CMC and change configuration. 0x00000001 + 0x00000002 = 0x00000003 The user may login to iDRAC, access Virtual Media, and Virtual Console. 0x00000001 + 0x00000040 + 0x00000080 = 0x000000C1 cfgUserAdminUserName (Read/Write) Description The name of the user for this index. The user index is created by writing a string into this name field if the index is empty. Writing a string of double quotes ("") deletes the user at that index. You cannot change the name.
cfgUserAdminSolEnable (Read/Write) Description Enables or disables Serial Over LAN (SOL) user access for the user. This object property is specific to iDRAC. Legal Values Default • • 1 (TRUE) 0 (FALSE) 0 cfgUserAdminIpmiSerialPrivilege (Read/Write) Description The maximum privilege on the IPMI LAN channel. This object is applicable only for iDRAC on Rack and Tower Servers and not for iDRAC Enterprise on Blade Servers or CMC.
cfgEmailAlertEnable (Read/Write) Description Enables or disables the alert instance. Legal Values Default • • 1 (TRUE) 0 (FALSE) 0 cfgEmailAlertAddress (Read/Write) Description Specifies the destination email address for email alerts, for example, user1@company.com. Legal Values E-mail address format, with a maximum length of 64 ASCII characters. Default cfgEmailAlertCustomMsg (Read/Write) Description Specifies a custom message that forms the subject of the alert.
RACADM sessions. Changes to idle timeout settings take effect at the next login. To disable idle timeout for a connection, set this property to 0. Use the -m option to apply this setting to iDRAC. The following sections provide information about the objects in the cfgSessionManagement group. cfgSsnMgtRacadmTimeout (Read/Write) Description Defines the idle timeout in seconds for the Remote RACADM interface.
• In case of iDRAC Enterprise on Blade Servers: Session timed out. Closing the session. After the message is displayed, the system returns to the shell that generated the Secure Shell session. Legal Values • • 0 (No timeout) 60 – 10800 NOTE: If 0 (no timeout), the network connection does not send keep alive packets to probe the client. Otherwise, keep alive packets are sent to guarantee that the client is responding.
cfgSerialBaudRate (Read/Write) Description Sets the baud rate on iDRAC or CMC serial port. Legal Values Default • • For iDRAC: 9600, 28800, 57600, 115200 For CMC: 2400, 4800, 9600, 19200, 28800, 38400, 57600,115200 • • For iDRAC: 57600 For CMC: 115200 cfgSerialConsoleEnable (Read/Write) Description Legal Values Default Enables or disables the RAC or CMC serial console interface.
NOTE: The CTRL key does not generate a character by itself, but must be struck simultaneously with another key to generate a character. For example, striking both the CTRL key and the \ key simultaneously (rather than sequentially) is denoted as ^\.
Default cfgSerialConsoleColumns Description Specifies the number of columns in the terminal window command line connected to the serial port. You must log out, then log in again for the changes to take effect. This object property is applicable only for CMC. NOTE: The prompt counts as two characters. NOTE: The terminal emulator must be configured with the line wrap mode ON, if a terminal emulator is used.
Example racadm getconfig -g cfgSerial cfgSerialBaudRate=115200 cfgSerialConsoleEnable=1 cfgSerialConsoleQuitKey=^\ cfgSerialConsoleIdleTimeout=1800 cfgSerialConsoleNoAuth=0 cfgSerialConsoleCommand= cfgSerialConsoleColumns=0 cfgSerialHistorySize=8192 cfgSerialTelnetEnable=0 cfgSerialSshEnable=1 cfgSerialTelnetEnable (Read/Write) Description Enables or disables the Telnet console interface on iDRAC or CMC.
Example racadm getconfig -g cfgOobSnmp cfgOobSnmpTrapsEnable=1 cfgOobSnmpAgentCommunity=public cfgOobSnmpAgentEnable (Read/Write) Description Enables or disables the SNMP agent in iDRAC or CMC. Legal Values Default • • 1 (TRUE) 0 (FALSE) 0 cfgTraps This group displays information for and configures delivery of SNMP traps for a specific user. This object property is applicable only to CMC. Use this object with the config or getconfig subcommands.
cfgTrapsCommunityName Description Sets the community string (identical to the community name) used for authentication. The community string acts as a password shared between different hosts over the network. This community string value must match with that of the other hosts for any kind of communication through SNMP. Legal Values A string representing the community name.
Default 1 cfgRacTuneCtrlEConfigDisable Description Enables or disables the ability of the local user to configure iDRAC from the BIOS POST option-ROM. This object is applicable only for iDRAC on Rack and Tower Servers and not for iDRAC Enterprise on Blade Servers or CMC. Legal Values Default • • 1 (TRUE) 0 (FALSE) 0 cfgRacTuneHttpPort (Read/Write) Description Specifies the port number to use for HTTP network communication with iDRAC or CMC.
cfgRacTuneIpRangeAddr (Read/Write) Description Specifies the acceptable IPv4 address bit pattern in positions determined by the "1"s in the range mask property (cfgRacTuneIpRangeMask). For CMC, a login from the incoming IP address is allowed only if the following are identical: • • cfgRacTuneIpRangeMask bit-wise and with incoming IP address cfgRacTuneIpRanbeMask bit-wise and with cfgRacTuneIpRangeAddr Legal Values An IPv4 address formatted string, for example, 192.168.0.44. Default 192.168.1.
Default 5 cfgRacTuneIpBlkFailWindow (Read/Write) Description Defines the time span in seconds that the failed attempts are counted. When failure attempts age beyond this limit, they are dropped from the count. Legal Values Default • • For iDRAC: 10 – 655356 For CMC: 2 – 655356 60 cfgRacTuneIpBlkPenaltyTime (Read/Write) Description Defines the time span in seconds that session requests from an IP address with excessive failures are rejected.
cfgRacTuneConRedirEnable (Read/Write) Description Enables or disables Virtual Console. This object property is applicable only to iDRAC. Legal Values • • Default 1 (TRUE) 0 (FALSE) 1 cfgRacTuneConRedirEncryptEnable (Read/Write) Description Encrypts the video in a Virtual Console session. This object property is applicable only to iDRAC. Legal Values • • Default 1 (TRUE) 0 (FALSE) 1 cfgRacTuneAsrEnable (Read/Write) Description Enables or disables iDRAC last crash screen capture feature.
cfgRacTuneIpRangeAddr=192.168.1.1 cfgRacTuneIpRangeMask=255.255.255.0 cfgRacTuneIpBlkEnable=0 cfgRacTuneIpBlkFailCount=5 cfgRacTuneIpBlkFailWindow=60 cfgRacTuneIpBlkPenaltyTime=300 # cfgRacTuneTimezoneOffset=-18000 # cfgRacTuneDaylightOffset=3600 cfgRacTuneTimezoneOffset (Read Only) Description Specifies the time zone offset (in minutes) from Greenwich Mean Time (GMT)/Coordinated Universal Time (UTC) to use for the RAC Time.
cfgRacTuneLocalConfigDisable (Read/Write) Description Disables write access to iDRAC configuration data. NOTE: Access can be disabled using the local RACADM or iDRAC Web interface; however, once disabled, access can be re-enabled only through iDRAC Web interface. This object property is applicable only to iDRAC. Legal Values Default • • 0 (TRUE-Enables) 1 (FALSE-Disables) 0 cfgRacTuneWebserverEnable (Read/Write) Description Enables or disables iDRAC or CMC web server.
session user gets a read only access after the default timeout value of 30 seconds.) 2 (If the user of the first session has not responded for session sharing request by subsequent user, the next session user gets administrator access after default timeout value of 30 seconds.) Default 0 cfgRacTunePluginType (Read/Write) Description Legal Values Default Specifies the plug-in type to use when running virtual console from browser. This object property is applicable only to iDRAC.
cfgVirMediaAttached (Read/Write) Description This object is used to attach virtual devices to the system via the USB bus. When the devices are attached, the server recognizes valid USB mass storage devices attached to the system. This is equivalent to attaching a local USB CDROM/floppy drive to a USB port on the system. When the devices are attached, they can be connected to the virtual devices remotely using iDRAC Web interface or the CLI.
cfgSDWriteProtect (Read Only) Description Displays if the physical write protect latch on the SD card is enabled or disabled. NOTE: This command is deprecated from iDRAC 1.5 and CMC 3.0 releases onwards. The functionality of this command is now covered by cfgVFlashSDWriteProtect. While execution of the cfgSDWriteProtect command is successful, it is recommended to use the cfgVFlashSDWriteProtect command. For more information, see "cfgVFlashSDWriteProtect" on page 132.
Default None cfgServerServiceTag (Read Only) Description Displays the service tag of the specified server. This object is applicable only to CMC. Legal Values None Default None cfgServerName (Read/Write) Description Displays the name of the specified server. This object is applicable only to CMC. Legal Values Maximum of 15 non-extended ASCII characters, (ASCII codes 32 through 126). For more information, see Guidelines to Quote Strings Containing Special Characters When Using RACADM Commands.
cfgServerNic1MacAddress (Read Only) Description Displays the MAC address of the server NIC 1. This object is applicable only to CMC. Legal Values None Default None cfgServerNic2MacAddress (Read Only) Description Displays the MAC address of the server NIC 2. This object is applicable only to CMC. Legal Values None Default None cfgServerNic3MacAddress (Read Only) Description Displays the MAC address of the server NIC 3. This object is applicable only to CMC.
cfgServerNicEnable (Read/Write) Description Enables or disables LAN channel. This object is applicable only to CMC. Legal Values Default • • 1 (Enable) 0 (Disable) None cfgServerIPMIOverLanEnable (Read/Write) Description Enables or disables IPMI LAN channel. This object is applicable only to CMC. Legal Values Default • • 1 (enable) 0 (disable) None cfgServerPowerBudgetAllocation (Read Only) Description Legal Values Default Displays the current power allocation for the server.
cfgServerDNSIMCName (Read/Write) Description Displays the DNS domain name for the integrated Remote Access Controller (iDRAC.) This object is applicable only to CMC. Legal Values None Default None cfgServerRootPassword (Write Only) Description Displays the password for iDRAC as a series of asterisks (*). It cannot be seen or displayed after this property is written. This object is applicable only to CMC.
cfgServerBootOnce (Read/Write) Description Enables or disables the server boot once feature. For CMC, this object is Write only. Legal Values Default • • 1 = TRUE 0 = FALSE 0 cfgServerPowerConsumption (Read Only) Description Displays the current power consumption for a server. This object is applicable only to CMC.
# cfgServerServiceTag=1S0M0G1 cfgServerName=SLOT-01 # cfgServerFW=1.40 (Build 12) # cfgServerBIOS=4.0.
cfgADRootDomain Description Specifies the root domain of the domain forest. This object is applicable only to CMC. Legal Values Any printable text string of up to 254 characters, with no white space. Default cfgADEnable (Read/Write) Description Enables or disables Active Directory user authentication on iDRAC or CMC. If this property is disabled on iDRAC, only local iDRAC authentication is used for user logins.
cfgADDomainController Description Specifies the AD server from which you want the CMC to obtain user names. Must be used with cfgADSpecifyServerEnable. This object is applicable only to CMC. Legal Values Valid IP address or fully qualified domain name (FQDN). Default None cfgADDomainController1 (Read/Write) Description Specifies the LDAP server from which you want the iDRAC to obtain user names . This object is applicable only to iDRAC.
Default 120 cfgADType (Read/Write) Description Determines the schema type to use with Active Directory. Legal Values • • Default 1 (Enables Active Directory with the extended schema) 2 (Enables Active Directory with the standard schema) 1 cfgADSpecifyServerEnable Description Allows you to enable or disable and specify an LDAP server or a global catalog server. Use cfgADDomainController or cfgADGlobalCatalog to specify the IP address. This object is applicable only to CMC.
cfgADGlobalCatalog1 (Read/Write) Description Specifies the Global Catalog server from which you want the iDRAC to obtain user names. This object is applicable only to iDRAC. Legal Values A string of up to 254 ASCII characters representing a valid IP address or a fully qualified domain name (FQDN). Default None cfgADGlobalCatalog2 (Read/Write) Description Specifies the Global Catalog server from which you want the iDRAC to obtain user names. This object is applicable only to iDRAC.
cfgAdDomainController3. iDRAC does not fail over to the specified domain controllers when DNS lookup fails or none of the servers returned by the DNS lookup works. This object is applicable only to iDRAC. Legal Values • • Default 1 (TRUE)—use DNS to look up domain controllers 0 (FALSE)—use pre‑configured domain controllers 0 cfgADDcSRVLookupbyUserdomain (Read/Write) Description Chooses the way the user domain is looked up for Active Directory. This object is applicable only to iDRAC.
cfgADGcRootDomain (Read/Write) Description The name of the Active Directory root domain used for DNS look up, to locate Global Catalog servers. This object is applicable only to iDRAC. Legal Values String. Maximum length = 254 Default Null cfgLDAP This group allows you to configure settings related to the Lightweight Directory Access Protocol (LDAP). Use this object with the config or getconfig subcommands.
cfgLdapPort (Read/Write) Description Port of LDAP over SSL. Non-SSL port is not supported. Legal Values 1 - 65535 Default 636 cfgLdapBasedn (Read/Write) Description The Domain Name of the branch of the directory where all searches should start from. Legal Values String. Maximum length = 254 Default Null cfgLdapUserAttribute (Read/Write) Description Specifies the user attribute to search for.
cfgLdapGroupAttributeIsDN (Read/Write) Description For iDRAC: When it is set to 1, iDRAC compares the userDN retrieved from the directory to compare to the members of the group; if it is set to 0, the user name provided by the login user is used to compare to the members of the group. This does not impact the search algorithm for the bind. iDRAC always searches the userDN and uses the userDN to bind.
• Default For CMC: String of maximum length = 1024 characters (objectclass=*) Searches for all objects in tree. cfgLDAPCertValidationEnable (Read/Write) Description Controls certificate validation during SSL handshake. Legal Values • • Default 1 (TRUE)—iDRAC or CMC uses the CA certificate to validate the LDAP server certificate during SSL handshake. 0 (FALSE)—iDRAC or CMC skips the certificate validation step of SSL handshake.
This object is applicable only to CMC. Legal Values String of maximum length of 254 alphanumeric characters and hyphens. The string must begin with a letter. Default [null] cfgLDAPSRVLookupServiceName (Read/Write) Description Configures the service name to be used in the SRV lookup. This object is applicable only to CMC. Legal Values String of maximum length of 254 characters. Default ldap cfgLdapRoleGroup For iDRAC, this group allows the user to configure role groups for LDAP.
cfgLdapRoleGroupDN (Read/Write) Description This is the Domain Name of the group in this index. For CMC, configure the LDAP distinguished name (DN) for the role group instance. Legal Values String. Maximum length = 1024 Default None Example racadm getconfig -g cfgLDAPRoleGroup -o cfgLDAPRoleGroupDN -i 1 cn=everyone,ou=groups,dc=openldap,dc=com cfgLdapRoleGroupPrivilege (Read/Write) Description A bit–mask defining the privileges associated with this particular group.
cfgLocationRack (Read/Write) Description Indicates rack where server is located. Legal Values String of up to 128 ASCII characters Default 0 cfgLocationRackslot (Read/Write) Description Indicates slot where server is located. Legal Values Values from 1 - 255 (1 Byte) Default 0 cfgLocationDevicesize (Read Only) Description Indicates server chassis size.
cfgSSADRoleGroupDomain (Read/Write) Description Active Directory Domain in which the Role Group resides. Legal Values Any printable text string of up to 254 characters, with no white space. Default cfgSSADRoleGroupPrivilege (Read/Write) Description Use the bit mask numbers listed in the table below to set role-based authority privileges for a Role Group.
The following sections provide information about the objects in the cfgChassisPower group. cfgChassisExternalPowerManagementMode Description Allows to enable or disable External Power Management. When this mode is enabled: • • • The chassis power capacity is set to maximum value. The server power priorities are set to 1. These properties cannot be changed by racadm or GUI. When the external power management mode is disabled, the power capacity and server power priorities are preserved.
Default None cfgChassisMinPowerTimestamp (Read Only) Description The timestamp recorded when the minimum system power occurred. Legal Values None Default None cfgChassisPowerStatus (Read Only) Description Legal Values Default Indicates the power status of the chassis. • • • • • • 1 (other) 2 (unknown) 3 (OK) 4 (non-critical) 5 (critical) 6 (non-recoverable) None cfgChassisRedundantState (Read Only) Description Legal Values Default Enables or disables power redundancy for the chassis.
than the minimum power required for the chassis configuration. Legal Values 2715 – 16685 watts Default 16685 watts cfgChassisPowerCapBTU (Read/Write) Description Indicates the maximum power consumption limit (in BTU/hr) for the entire chassis. The command generates an error if server throttling is necessary to achieve the power goal based on the value for this setting.
cfgChassisRedundancyPolicy (Read/Write) Description Sets the redundancy policy of the chassis. Legal Values • • • Default 0 (no redundancy) 1 (AC redundancy) 2 (power supply redundancy) 0 (no redundancy) cfgChassisDynamicPSUEngagementEnable (Read/Write) Description Enables or disables dynamic engagement.
cfgChassisPerformanceOverRedundancy (Read/Write) Description Enables or disables server performance over power redundancy. When enabled, this option favors server performance and server powerup, over maintaining power redundancy. When disabled, the system favors power redundancy over server performance.
Default None cfgChassisTotalInPowerAvailable (Read Only) Description Indicates the amount of power (in watts) available for use by the chassis. Legal Values None Default None cfgChassisStandbyInPowerCapacity (Read Only) Description Indicates the amount of power (in watts) available for powering up any hardware modules that are either added to the chassis or powered up (if they are already present in the chassis).
Default None Examples • racadm getconfig -g cfgChassisPower # cfgChassisInPower=0 W | 0 BTU/hr # cfgChassisPeakPower=0 W # cfgChassisPeakPowerTimestamp=06:32:55 01/26/2009 # cfgChassisMinPower=0 W # cfgChassisMinPowerTimestamp=06:32:55 01/26/2009 # cfgChassisPowerStatus=5 # cfgChassisRedundantState=0 cfgChassisPowerCap=16685 W cfgChassisPowerCapF=16685 W cfgChassisPowerCapBTU=56931 BTU/hr cfgChassisPowerCapFBTU=56931 BTU/hr cfgChassisPowerCapPercent =100% cfgChassisPowerCapFPercent =100% cfgChassisRedund
cfgIpmiSolBaudRate (Read/Write) Description Specifies baud rate for serial communication over LAN. Legal Values 9600, 19200, 57600, 115200 Default 115200 cfgIpmiSolMinPrivilege (Read/Write) Description Specifies the minimum privilege level required for SOL access. Legal Values Default • • • 2 (User) 3 (Operator) 4 (Administrator) 4 cfgIpmiSolAccumulateInterval (Read/Write) Description Specifies the typical amount of time that iDRAC waits before transmitting a partial SOL character data packet.
• Default 0 (FALSE) 0 cfgIpmiLanPrivLimit (Read/Write) Description Specifies the maximum privilege level allowed for IPMI over LAN access. Legal Values Default • • • 2 (User) 3 (Operator) 4 (Administrator) 4 cfgIpmiLanAlertEnable (Read/Write) Description Enables or disables global e-mail alerting. This property overrides all individual e-mail alerting enable/disable properties.
cfgIpmiPetIPv6Index (Read Only) Description Unique identifier for the index corresponding to the trap. Legal Values 1–4 Default cfgIpmiPetIPv6AlertDestIpAddr Description Configures the IPv6 alert destination IP address for the trap. Legal Values IPv6 address Default cfgIpmiPetIPv6AlertEnable (Read/Write) Description Enables or disables the IPv6 alert destination for the trap.
Default The index value of a platform event filter object. cfgIpmiPefAction (Read/Write) Description Specifies the action that is performed on the managed server when the alert is triggered. NOTE: For iDRAC on Rack and Tower servers, this object is read-only for indexes 20, 21, and 22. Legal Values Default • • • • 0 (None) 1 (Power Down) 2 (Reset) 3 (Power Cycle) 0 cfgIpmiPefEnable (Read/Write) Description Enables or disables a specific platform event filter.
cfgIpmiPetAlertEnable (Read/Write) Description Enables or disables a specific trap. Legal Values Default • • 1 (TRUE) 0 (FALSE) 0 cfgUserDomain This group is applicable only for iDRAC and is used to configure the Active Directory user domain names. A maximum of 40 domain names can be configured at any given time. The following sections provide information about the objects in the cfgUserDomain group. cfgUserDomainIndex (Read Only) Description Represents a specific domain.
cfgServerPowerAllocation (Read Only) Description Represents the available allocated power supply for server usage. NOTE: In case of more than one power supply, this object represents the minimum capacity power supply. NOTE: This object is applicable only for iDRAC Enterprise on Rack and Tower Servers and not for iDRAC on Blade Servers or CMC.
cfgServerMaxPowerCapacity (Read Only) Description Represents the maximum server power capacity based on the current component consumption. This object is applicable only for iDRAC. Legal Values Not applicable Default cfgServerPeakPowerConsumption (Read Only) Description Represents the maximum power consumed by the server until the current time. This object is applicable only for iDRAC.
cfgServerPowerCapBtuhr (Read/Write) Description Represents the server power threshold in BTU/hr. This object is applicable only for iDRAC. NOTE: This value is applicable only if cfgServerPowerCapEnable is set to 1. Legal Values None Default Server power threshold in BTU/hr. cfgServerPowerCapPercent (Read/Write) Description Represents the server power threshold in percentage. This object is applicable only for iDRAC. NOTE: This value is applicable only if cfgServerPowerCapEnable is set to 1.
cfgServerPowerLastHourMinPower (Read Only) Description Displays the minimum power value during the last hour. This object is applicable only for iDRAC. Legal Values Not applicable Default Minimum power value during the last hour. cfgServerPowerLastHourMinTime (Read Only) Description Displays the timestamp of minimum power value during the last minute. This object is applicable only for iDRAC.
• • • • Default YYYY = Year HH = hour MM=Minutes SS = Seconds Maximum power value during the last hour. cfgServerPowerLastDayMinPower (Read Only) Description Displays the minimum power value during the last day. This object is applicable only for iDRAC. Legal Values Not applicable Default Minimum power value during the last day. cfgServerPowerLastDayMinTime (Read Only) Description Displays the timestamp of minimum power value during the last day. This object is applicable only for iDRAC.
cfgServerPowerLastDayMaxTime (Read Only) Description Displays the timestamp of maximum power value during the last day. This object is applicable only for iDRAC. Legal Values Time in the format: DD MM Date HH:MM:SS YYYY where, • • • • • • • Default DD = Day of the week MM = Month Date = Date YYYY = Year HH = hour MM = Minutes SS = Seconds Maximum power value during the last day. cfgServerPowerLastWeekMinPower (Read Only) Description Displays the minimum power value during the last week.
cfgServerPowerLastWeekMaxPower (Read Only) Description Displays the maximum power value during the last week. This object is applicable only for iDRAC. Legal Values None Default Maximum power value during the last week. cfgServerPowerLastWeekMaxTime (Read Only) Description Displays the timestamp of maximum power value during the last week. This object is applicable only for iDRAC. Legal Values A string of up to 32 characters.
Default Difference between the available power and the peak power consumption. cfgServerActualAmperageConsumption (Read Only) Description Displays the current power consumption. This object is applicable only for iDRAC. Legal Values Not applicable Default Current power consumption. cfgServerPeakAmperage (Read Only) Description Displays the current peak power consumption. Legal Values Not applicable Default Current peak power consumption.
cfgServerCumulativePowerConsumptionTimeStamp (Read Only) Description Displays the timestamp of the cumulative power consumption. This object is applicable only for iDRAC. Legal Values A string of up to 32 characters. Time in the format: DD MM Date HH:MM:SS YYYY where, • • • • • • • Default DD = Day of the week MM= Month Date=Date YYYY = Year HH = hour MM=Minutes SS = Seconds Timestamp of the cumulative power consumption.
cfgKVMAccessToCMCEnable Description Enables or disables the Dell CMC Console access on the iKVM. Legal Values • • Default 1 (enable) 0 (disable) None cfgKVMFrontPanelEnable Description Enables or disables front panel access on the iKVM. Legal Values • • Default 1 (enable) 0 (disable) None Example racadm getconfig -g cfgKVMInfo cfgKVMAccessToCMCEnable=1 cfgKVMFrontPanelEnable=1 cfgAlerting This group is enables or disables SNMP event trap alerting and sets the event filter.
cfgAlertingSourceEmailName Description Specifies e-mail address used to send e-mail notifications when an event occurs. Legal Values None Default None Examples racadm getconfig -g cfgAlerting -o cfgAlertingSourceEmailName racadm config -g cfgAlerting -o cfgAlertingSourceEmailName user@home.com Object value modified successfully. cfgLcdLocale Description Specifies the Language (locale) for the Blade Chassis LCD interface. Legal Values de, fr, en, es, ja, zh-cn.
cfgServerPowerSupplyMaxInputPower (Read Only) Description Displays the AC input rated power in Watts. Legal Values A string of up to 32 characters. Default 0 cfgServerPowerSupplyMaxOutputPower (Read Only) Description Displays the AC output rated power in Watts. Legal Values A string of up to 32 characters. Default 0 cfgServerPowerSupplyOnlineStatus (Read Only) Description Displays the status of the power supply unit.
cfgIPv6LanNetworking This group is used to configure the IPv6 over LAN networking capabilities. Use this object with the config or getconfig subcommands. To use this object property for CMC, you must have Chassis Configuration Administrator privilege. NOTE: Use the -m option to apply this setting to iDRAC. The following sections provide information about the objects in the cfgIPv6LanNetworking group. cfgIPv6Enable (Read/Write) Description Enables or disables iDRAC or CMC IPv6 stack.
cfgIPv6PrefixLength (Read/Write) Description Specifies the prefix length for iDRAC or CMC IPv6 address. NOTE: For CMC, this property is used only if cfgIPv6AutoConfig is set to 0 (false) Legal Values For iDRAC: 1 - 128 For CMC: 0 - 128 Default 64 cfgIPv6AutoConfig (Read/Write) Description Enables or disables the IPv6 Auto Configuration option. NOTE: If this value is set to 0, the CMC disables auto configuration and statically assigns IPv6 addresses.
cfgIPv6Address3 (Read Only) Description The iDRAC IPv6 third address. This object is applicable only for iDRAC. Legal Values String representing a valid IPv6 entry. Default :: cfgIPv6Address4 (Read Only) Description The iDRAC IPv6 fourth address. This object is applicable only for iDRAC. Legal Values String representing a valid IPv6 entry. Default :: cfgIPv6Address5 (Read Only) Description The iDRAC IPv6 fifth address. This object is applicable only for iDRAC.
Default :: cfgIPv6Address9 (Read Only) Description The iDRAC IPv6 ninth address. This object is applicable only for iDRAC. Legal Values String representing a valid IPv6 entry. Default :: cfgIPv6Address10 (Read Only) Description The iDRAC IPv6 tenth address. This object is applicable only for iDRAC. Legal Values String representing a valid IPv6 entry. Default :: cfgIPv6Address11 (Read Only) Description The iDRAC IPv6 eleventh address. This object is applicable only for iDRAC.
cfgIPv6Address14 (Read Only) Description The iDRAC IPv6 fourteenth address. This object is applicable only for iDRAC. Legal Values String representing a valid IPv6 entry. Default :: cfgIPv6Address15 (Read Only) Description The iDRAC IPv6 fifteenth address. This object is applicable only for iDRAC. Legal Values String representing a valid IPv6 entry.
Default :: Example $ racadm getconfig -g cfgIPv6LanNetworking cfgIPv6Enable=1 cfgIPv6AutoConfig=1 cfgIPv6Address=:: cfgIPv6PrefixLength=64 cfgIPv6Gateway=:: cfgIPv6DNSServersFromDHCP6=1 cfgIPv6DNSServer1=:: cfgIPv6DNSServer2=:: If both IPv4 and IPv6 are enabled on the CMC, IPv6 DNS servers take priority.
Description Displays the static gateway for the CMC IP address. Legal Values Default cfgNicCurrentDhcpWasUsed Description Indicates whether DHCP is used to configure the NIC. Legal Values 0 – address is static. 1– address was obtained from the DHCP server. Default None cfgNicCurrentVlanEnable (Read Only) Description Indicates whether the VLAN is enabled.
Default cfgDNSCurrentDomainName Description Displays the DNS domain name. Legal Values Default cfgNicCurrentIPv4Enabled Description Indicates whether IPv4 is enabled on the CMC. If the current property value is set to 0 (false), the remote network interfaces to the CMC are not accessible over IPv4. Legal Values Default Example racadm getconfig -g cfgCurrentLanNetworking # cfgNicCurrentIPv4Enabled=1 # cfgNicCurrentIpAddress=143.166.152.116 # cfgNicCurrentNetmask=255.255.255.
cfgCurrentIPv6AutoConfigWasUsed Description Indicates whether auto configuration is used to obtain IPv6 settings, including stateless IPv6 address(es) and gateway. Legal Values 0 (static addressing is used) 1 (address is obtained from the DHCPv6 server and/or stateless auto configuration) Default None cfgCurrentLinkLocalAddress Description Displays the current IPv6 link-local address of the CMC. Legal Values Default cfgCurrentIPv6Address1 Description Displays the current IPv6 addresses.
Default cfgCurrentIPv6DNSServer2 Description Displays the IPv6 address for DNS server 2.
cfgIpmiSerialConnectionMode (Read/Write) Description When the iDRAC cfgSerialConsoleEnable property is set to 0 (disabled), the iDRAC serial port becomes the IPMI serial port. This property determines the IPMI defined mode of the serial port. In Basic mode, the port uses binary data with the intent of communicating with an application program on the serial client. In Terminal mode, the port assumes that a dumb ASCII terminal is connected and allows very simple commands to be entered.
cfgIpmiSerialLineEdit (Read/Write) Description Enables or disables line editing on the IPMI serial interface. Legal Values Default • • 0 (FALSE) 1 (TRUE) 1 cfgIpmiSerialEchoControl (Read/Write) Description Enables or disables echo control on the IPMI serial interface. Legal Values Default • • 0 (FALSE) 1 (TRUE) 1 cfgIpmiSerialDeleteControl (Read/Write) Description Enables or disables delete control on the IPMI serial interface.
cfgIpmiSerialInputNewLineSequence (Read/Write) Description Specifies the input newline sequence specification for the IPMI serial interface. Legal Values Default • • 1 (ENTER) 2 (NULL) 1 cfgSmartCard This group specifies properties used to support access to iDRAC using a smart card. This group is applicable only for iDRAC. The following sections provide information about the objects in the cfgSmartCard group.
This group is applicable only for iDRAC on Rack and Tower Servers and not for iDRAC Enterprise on Blade Servers. CAUTION: Use extra precaution when modifying properties in this group. Inappropriate modification of the properties in this group can result in your RAC NIC become inoperable. cfgNetTuningNicSpeed Description Specifies the speed for the CMC NIC. This property is used only if cfgNetTuningNicAutoNeg is set to 0.
• Default 1 (Full Duplex) 1 cfgNetTuningNicMtu (Read/Write) Description The size in bytes of the maximum transmission unit used by iDRAC or CMC NIC. Legal Values 576 – 1500 Default 1500 NOTE: IPv6 requires a minimum MTU of 1280. If IPv6 is enabled, and cfgNetTuningMtu is set to a lower value, the CMC uses an MTU of 1280. cfgSensorRedundancy This group is used to set the power supply redundancy. This group is applicable only for iDRAC.
cfgSensorRedundancyCapabilities (Read Only) Description Returns the redundancy capabilities in the form of a bitmask. This bitmask allows the user to know which values can be set for cfgSensorRedundancyPolicy. Legal Values A bit mask. More than 1-bit can be set at a time to indicate multiple redundancy support.
cfgVFlashSDEnable (Read/Write) Description Enables or disables the vFlash SD card. NOTE: Disabling vFlashPartition by setting cfgVFlashSDEnable to 0 does not require a license. Legal Values Default • • 0 (Disable) 1 (Enable) 1 cfgVFlashSDSize (Read Only) Description Displays the size of the vFlash SD card in megabytes (MB). Legal Values A string of upto 64 characters.
• Default Unknown OK cfgVFlashSDWriteProtect (Read Only) Description Displays whether the physical write-protect latch on the vFlash SD card is enabled or disabled. Legal Values Default • • 0 (vFlash is not write-protected) 1 (vFlash is write-protected) None cfgVFlashPartition This group is used to configure properties for individual partitions on the vFlash SD Card. Up to 16 partitions are supported, indexed from 1 to 16. This group is applicable only for iDRAC.
cfgVFlashPartitionOSVolLabel ReadOnly Description Displays the label for the partition that is visible to the operating system. Legal Values An alphanumeric string of up to six characters. Default None cfgVFlashPartitionFormatType (ReadOnly) Description Displays the format type of the partition. Legal Values String: • • • • • • Default FAT16 FAT32 EXT2 EXT3 CD RAW None cfgVFlashPartitionAccessType (Read/Write) Description Indicates the partition access permissions.
cfgLogging This group contains parameters to enable or disable the OEM event log filtering. This group is applicable only for iDRAC. The following section provide information about the objects in the cfgLogging group: cfgLoggingSELOEMEventFilterEnable (Read/Write) Description Enables or disables the SEL Log filtering. Legal Values Default • • 0 (Disable) 1 (Enable) 0 cfgRacSecurity This group is used to configure settings related to CMC SSL certificate signing request (CSR) feature.
Default cfgRacSecCsrLocalityName (Read/Write) Description Specifies the CSR Locality (L). Legal Values A string of up to 254 characters. Default cfgRacSecCsrStateName (Read/Write) Description Specifies the CSR State Name (S). Legal Values A string of up to 254 characters. Default cfgRacSecCsrCountryCode (Read/Write) Description Specifies the CSR Country Code (CC). Legal Values A string of 2 alphabet country code.
Database Objects With Get and Set Commands 4 These groups and object names must be used with the get and set commands. When addressing these objects they must begin with either a FQDD or FQDD Alias. These groups and objects are not applicable for CMC. System.Power This group provides information on power management features for iDRAC. The following section provides information about the objects in the System.Power group. System.Power.
Default None System.Power.Cap.Enable (Read/Write) Description Enables Server Capping. NOTE: This value is read only on Blade servers because CMC controls the capping. Legal Values Default • • 0 - Disable 1 - Enable 0 System.Power.Cap.Watts (Read Only) Description Represents the Maximum Power in Watts a device is allowed to consume. The device may throttle in order to meet this capacity. NOTE: This value is applicable only if System.Power.Cap.Enable is set to 1.
System.Power.Hotspare.Enable (Read/Write) Description Enables RapidOn feature for the primary PSU selection. NOTE: This value is supported only on iDRAC on Rack and Tower servers. Legal Values 0 - Disable 1- Enable Default 0 System.Power.PFC.Enable (Read/Write) Description Enables the power factor correction feature. NOTE: This value is supported only on iDRAC on Rack and Tower servers. NOTE: This value is applicable only if System.Power.Cap.Enable is set to 1.
Time in the format Day Month Date HH:MM:SS Year • • • • • • Default HH = hour MM=Minutes SS = Seconds OO = Month DD = Day YYYY = Year None System.Power.Max.PowerClear Write Only Description Clears the current recorded power statistics. Legal Values 0 - Do not clear 1 - Clear the Power Consumption Statistics Default None System.Power.Avg.LastHour (Read Only) Description Displays the average power value during the last hour. Legal Values Integer > 0 Default None System.Power.Avg.
System.Power.Max.LastDay.TimeStamp (Read Only) Description Displays the timestamp of maximum power value during the last day. Legal Values Time in the format Day Month Date HH:MM:SS Year • • • • • • Default HH = hour MM=Minutes SS = Seconds OO = Month DD = Day YYYY = Year 0 System.Power.Avg.LastWeek (Read Only) Description Displays the average power value during the last week. Legal Values Integer > 0 Default 0 System.Power.Min.LastWeek.
System.Power.Max.LastWeek.TimeStamp (Read Only) Description Displays the timestamp of maximum power value during the last week. Legal Values Time in the format Day Month Date HH:MM:SS Year • • • • • • Default HH = hour MM=Minutes SS = Seconds OO = Month DD = Day YYYY = Year 0 System.Power.RedundancyPolicy (Read/Write) Description Sets the redundancy policy of the system. NOTE: This object is not applicable on iDRAC on Blade servers. iDRAC on Blade servers does not control power supplies.
• Default 64 - 5+x Redundant 0 System.Power.RedundantState (Read Only) Description Retrieves the redundancy state for the chassis. Legal Values Default • • 0 - None 1 - Full 0 System.Power.Cap.Percent (Read/Write) Description Represents the maximum power as a percentage of total power that a device is allowed to consume. The device may throttle in order to meet this cap. NOTE: This value is applicable only if System.Power.Cap.Enable is set to 1. Legal Values String up to 32 characters.
System.Power.Max.Headroom Write Only Description Displays the difference between the available power and the current power consumption. NOTE: This object is not applicable on iDRAC on Blade servers. Legal Values Integer > 0 Default 0 System.Power.EnergyConsumption.StarttimeStamp Description Displays the Start time for the Power Consumption.
System.Power.Supply.[i].MaxInputPower (Read Only) Description Displays the AC input rated power in Watts. Legal Values Integer > 0 Default 0 System.Power.Supply.[i].MaxOutputPower ((Read Only)) Description Displays the DC output rated power in Watts. Legal Values Integer > 0 Default 0 System.Power.Supply.[i].Status (Read Only) Description Displays the status of the power supply unit. Legal Values Default • • • • 0 - absent 1 - present and OK 2 - failure 3 - predictive failure 0 System.
Default None System.Power.Supply.[i].LineStatus (Read Only) Description Specifies if this power supply is powered off or on. Legal Values Integer > 0 Default None System.Power.Supply.[i].PMBusMonitoring (Read Only) Description Specifies if this PMBus is present or not. Legal Values Integer > 0 Default 0 System.Location This group provides information on the server's physical location characteristics. This group is not applicable for iDRAC.
System.Location.Rack.Slot (Read/Write) Description Indicates the slot where server is located. Legal Values 1- 255 (1 Byte) Default 0 System.Location.DeviceSize (Read Only) Description Indicates server chassis size. Legal Values 1- 255 Default 0 System.Location.Chassis.Name Read or Write Description Indicates chassis name. Legal Values String of up to 127 ASCII characters Default 0 System.Location.Chassis.Slot Read Only Description Indicates chassis slot.
LifecycleController.LCAttributes.LifecycleControllerState (Read/Write) Description Configures the lifecycle controller state. Legal Values Default • • • 0 - Disable 1 - Enable 2 - Recovery mode 2 LifecycleController.LCAttributes.PartFirmwareUpdate (Read/Write) Description Configures the Part Firmware Update. Legal Values Default • • • 0 - Disable 1 - Allow version upgrade only. 2 - Match firmware of replaced part. 0 LifecycleController.LCAttributes.
iDRAC.IMC This group provides information on managing the administrative state of the Internal Management Communication (IMC.) iDRAC.IMC.AdministrativeState (Read/Write) Description Manage the administrative state of the IMC.