TM Dell D2201R monitor User Manual English 3\FFɤɢɣ Deutsch Français Svenska Suomi Italiano Español Dansk ㅔԧЁ᭛ Polski Nederlands 穢剳檺 Model: D2201Rc ModelM
TABLE OF CONTENTS For Your Safety ---------------------------------------------------------------- 1 Safety Precautions ------------------------------------------------------- 2 Special Notes on LCD Monitors -------------------------------------- 3 Before You Operate The Monitor -----------------------------------------Features -------------------------------------------------------------------Packing List --------------------------------------------------------------Installation Instructions --------------
Before operating the monitor, please read this manual thoroughly. This manual should be retained for future reference. FCC Class B Radio Frequency Interference Statement WARNING: (FOR FCC CERTIFIED MODELS) NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Precautions • Do not use the monitor near water, e.g. near a bathtub, washbowl, kitchen sink, laundry tub, swimming pool or in a wet basement. • Do not place the monitor on an unstable cart, stand, or table. If the monitor • • • • • • • • falls, it can injure a person and cause serious damage to the appliance. Use only a cart or stand recommended by the manufacturer or sold with the monitor.
Special Notes on LCD Monitors The following symptoms are normal with LCD monitor and do not indicate a problem. NOTES • Due to the nature of the fluorescent light, the screen may flicker during • • • • initial use. Turn off the power switch and then turn it on again to make sure the flicker disappears. You may find a little uneven brightness on the screen depending on the desktop pattern you use. The LCD screen has effective pixels of 99.99% or more. It may include blemishes of 0.
Installation Instructions Install Figure 1 Remove Installing and Removing the Base POWER CORD Power Source: 1. Ensure that the power cord is the correct type required in your area. 2. This LCD monitor has an external universal power supply that allows operation in either 100/120V AC or 220/240V AC voltage area (no user adjustment is required). 3.
Controls And Connectors Connecting the Signal Cable: Plug the Signal Cable one end to LCD monitor’s “DSUB-Input” socket , the other end to the computer’s VGA port and tighten the two screws on the cable connector. Connecting the DVI Cable : Connect one end of the 24-pin DVI cable to the back of the monitor and connect the other end to the computer's DVI port. Connecting the Power Cord: Connect one end of the AC power cord to the LCD monitor's AC input socket, and the other end to wall outlet.
Adjusting The Viewing Angle • For optimal viewing it is recommended to look at the full face of the monitor, then adjust the monitor’s angle to your own preference. • Hold the stand so you do not topple the monitor when you change the monitor’s angle. • You are able to adjust the monitor’s angle from -5° to 20°. Figure 3 NOTES • Do not touch the LCD screen when you change the angle. It may cause damage or break the LCD screen.
Operating Instructions General Instructions Press the power button to turn the monitor on or off. The other control buttons are located at front panel of the monitor (See Figure 4). By changing these settings, the picture can be adjusted to your personal preferences. • The power cord should be connected. • Connect the video cable from the monitor to the video card. • Press the power button to turn on the monitor position. The power indicator will light up. 6 5 4 3 2 1 Figure 4 1. 2 3. 4. 5. 6.
Front Panel Control • Power Button: Press this button to switch ON/OFF of monitor’s power. • Power Indicator: Blue — Power On mode. Orange — Power saving mode. • MENU/ENTER : Active OSD menu or function adjust confirm or Exit OSD menu when in Contrast/Brightness OSD status. • ECO Hotkey(-) Activates the ECO control when the OSD is off or navigate through adjustment icons when OSD is on or adjust a function when function is activated. • Image Ratio(+) : Select monitor display mode.
• To keep the monitor looking new, clean it with a soft cloth. Stubborn • • stains may be removed with a cloth lightly dampened with a mild detergent solution. Never use strong solvents such as thinner, benzene, or abrasive cleaners, since these will damage the cabinet. As a safety precaution, always unplug the monitor before cleaning it. Do not scratch the screen with hard things, it may cause permanent damage. Don’t leak liquid into monitor which will result in the damage of component.
Adjusting The Picture The descriptions for function control LEDS Main Main Sub Menu Menu Menu Item Item Icon Sub Menu Brightness Description Backlight Adjustment Contrast Contrast from Digital-register. Standard Standard Mode Text Luminance Text Mode Internet Internet Mode Eco Game Game Mode Movie Movie Mode Sports Sports Mode Off Disable dynamic contrast ratio On Enable dynamic contrast ratio DCR Clock Adjust picture Clock to reduce Vertical-Line noise.
Color Temp. Warm Recall Warm Color Temperature from EEPROM. Normal Recall Normal Color Temperature from EEPROM. Cool Recall Cool Color Temperature from EEPROM. sRGB Recall SRGB Color Temperature from EEPROM. User-B Blue Gain from Digital-register User User-G Green Gain Digital-register. User-R Red Gain from Digital-register OSD Setup H.Position Adjust the verticalposition of OSD V.
Plag And Play Plug & Play DDC2B Feature This monitor is equipped with VESA DDC2B capabilities according to the VESA DDC STANDARD. It allows the monitor to inform the host system of its identity and, depending on the level of DDC used, communicate additional information about its display capabilities. The DDC2B is a bidirectional data channel based on the I²C protocol. The host can request EDID information over the DDC2B channel.
Technical Support (FAQ) Problem Power LED is not on Possible Solution *Check if the Power Switch is in the ON position *Check if the PC system is Plug & Play compatible *Check if the video card is plug and play No Plug & Play compatible *Check if the D-15 plug pin of Video Cable is bent *Adjust the Contrast and Brightness Picture is fuzzy Controls. *Move electrical devices that may cause Picture bounces or a wave pattern is present in the picture electrical interference.
CLOCK (pixel frequency) controls the number of pixels scanned by one horizontal sweep. If the frequency is not correct, the screen shows vertical stripes and the picture has not correct width. FOCUS adjusts the phase of the pixel clock signal. With a wrong phase adjustment the picture has horizontal disturbances in light picture. For FOCUS and CLOCK adjustment 95/98/2000/ME/XP shut-down mode pattern. use “dot-pattern” or win Error Message & Possible Solution CABLE NOT CONNECTED : 1. 2.
Appendix Specifications LCD Panel Input Display Colors Dot Clock Max. Resolution Plug & Play Power Consumption Input Connector Input Video Signal Power Source Environmental Considerations Dimension Weight (N. W.) Driving system Size Pixel pitch Video TFT Color LCD 546.86 mm(21.5") 0.248( H ) ×0.248mm ( V ) R,G,B Analog Interface Digital Interface Separate Sync. H/V TTL H-Frequency 31kHz – 67.5kHz V-Frequency 56-75Hz 16.7M Colors 138.
• • • • • • • • • • • • • • • • • • • • • Power Button Menu Image Ratio(+) ECO/Source/Auto Contrast Brightness Phase Clock H. Position V.
Factory Preset Timing Table RESOLUTION HORIZONTAL FREQUENCY(kHz) 640×480 @60Hz 31.469 59.940 640×480 @72Hz 37.861 72.809 640×480 @75Hz 37.500 75.000 720×400 @70Hz 31.469 70.087 800×600 @56Hz 35.156 56.250 800×600 @60Hz 37.879 60.317 800×600 @72Hz 48.077 72.188 800×600 @75Hz 46.875 75.000 1024×768 @60Hz 48.363 60.004 1024×768 @70Hz 56.476 70.069 1024×768 @75Hz 60.023 75.029 WXGA 1280x768@60Hz 45.000 60.000 WXGA+ 1600x900@60Hz 60.000 60.
Connector Pin Assignment 1 5 6 10 11 15 15-Pin Color Display Signal Cable PIN NO. 1. 2. 3. 4. 5. 6. 7. 8. DESCRIPTION PIN NO. DESCRIPTION 9. 10. 11. 12. 13. 14. 15. +5V Ground Ground DDC-Serial Data H-Sync V-Sync DDC-Serial Clock Red Green Blue Ground Detect Cable R-Ground G-Ground B-Ground 24 - Pin Color Display Signal Cable(option) PIN NO. DESCRIPTION PIN NO. 1. 2. 3. TMDS Data 2TMDS Data 2+ TMDS Data 2/4 Shield TMDS Data 4TMDS Data 4+ DDC Clock 13. 14. 15. 4. 5. 6. 7. 8. 9. 10. 11.
