Dell™ OpenManage™ Server Administrator Version 5.2 Command Line Interface User's Guide w w w. d e l l . c o m | s u p p o r t . d e l l .
Notes and Notices NOTE: A NOTE indicates important information that helps you make better use of your computer. NOTICE: A NOTICE indicates either potential damage to hardware or loss of data and tells you how to avoid the problem. ____________________ Information in this document is subject to change without notice. © 2006 Dell Inc. All rights reserved. Reproduction in any manner whatsoever without the written permission of Dell Inc. is strictly forbidden.
Contents 1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . What's New for Version 5.2 . . . . . . . . . . . . . . . . . . . . . . . . . . . Using CLI Commands from Windows Command Prompts . Primary CLI Commands 14 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Success Messages . Failure Messages . . . . . . . . . . . . . . . . . . . . . . 15 . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 16 . . . . . . . . . . . . . . . . . . . . . . . .
omreport chassis fancontrol . . . omreport chassis firmware . . . . omreport chassis frontpanel . . . omreport chassis fru . . . . . . . omreport chassis info . . . . . . . omreport chassis intrusion . . . . omreport chassis leds . . . . . . omreport chassis memory . . . . omreport chassis nics . . . . . . omreport chassis ports . . . . . . omreport chassis processors. . . omreport chassis pwrsupplies . . omreport chassis remoteaccess . omreport chassis slots . . . . . . omreport chassis temps . . . . .
omconfig chassis . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . omconfig preferences . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Adding Depreciation Information . . . . . . . . . . . . . . . . . . . . . . . Adding Extended Warranty Information . 103 . . . . . . . . . . . . . . . . . . . 104 . . . . 104 . . . . . . . . . . . . . . . . . . . . . . . . . . . 105 Example Command for Adding Extended Warranty Information . Adding Lease Information . . . . . . . . . . . . 105 . . . . . . . . . . . . . . . . . . . . . . . 106 Example Command for Adding Lease Information Adding Maintenance Information . . . . . . . . 106 . .
omreport rac modem . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 116 omreport rac remote . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 116 . . . . . . . . . . . . . . . . . . . . . . . . . . . . 116 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 116 omreport rac snmptraps omreport rac users . omreport rac viewcertificate 7 . . . . . . . . . . . . . . . . . . . . . . . . . omconfig rac: Managing the Remote Access Controller . . . . . . . . . . . . . .
omconfig rac rmsnmptrap . . . . . . . . . . . . . . . . . . . . . . . . . . . 131 . . . . . . . . . . . . . . . . . . . . . . . . . . . . 131 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 131 Example Command omconfig rac rmuser . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 131 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 132 Example Command omconfig rac reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . 132 . . . . . . . . . . . . . . . . . .
omconfig Enable Controller Alarm . . . . . . . . omconfig Disable Controller Alarm . . . . . . . . omconfig Quiet Controller Alarm . . . . . . . . . omconfig Test Controller Alarm . . . . . . . . . . omconfig Reset Controller Configuration . . . . . omconfig Create Virtual Disk . . . . . . . . . . . omconfig Set Controller Rebuild Rate . . . . . . omconfig Set Background Initialization Rate . . . omconfig Set Reconstruct Rate . . . . . . . . . omconfig Set Check Consistency Rate . . . . . .
omconfig Physical Disk Commands . . . . . . . . . . . . . . . . . . . . . . omconfig Battery Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 177 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9 Working With CLI Command Results Output Options for Command Results . . . . . . . . . . . . . . . 187 . . . . . . . . . . . . . . . . . . . . . 187 . . . . . . . . . . . . 187 187 189 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 193 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 215 Controlling Command Output Display. . . . . . . Writing Command Output to a File . . . . . . . .
Contents
Introduction Whether you are using the graphical user interface (GUI) or the command line interface (CLI), Dell™ OpenManage™ Server Administrator performs essential systems management tasks. The reporting and viewing features allow retrieval of overall health status for systems on your network. At the component level, you can view information about the voltages, temperatures, current, fan RPM, memory functioning, and many other critical component details.
Using CLI Commands from Windows Command Prompts If you are running the Windows operating system, use the 32-bit command prompt to issue a Server Administrator CLI command. You can access the 32-bit command prompt by clicking the Start button and pointing to Programs→ Accessories→ Command Prompt shortcut, or by clicking the Start button and selecting Run, then typing cmd.exe in the Run dialog box.
Table 1-1 lists the primary CLI commands used by Server Administrator. This guide contains a section for each primary command. Table 1-1.
Message: BIOS setup configured successfully. Command: omconfig system assetinfo info=depreciation duration=6 Message: Asset information set successfully. Failure Messages CLI failure messages provide reasons why some commands do not succeed. Some common reasons why commands fail include syntax errors and components that are not present. Many error messages provide syntax information that you can use to execute the command successfully.
Scripting and Comparing With the CLI The Server Administrator CLI allows administrators to write batch programs or scripts to be executed by the operating system. For an enterprise with many systems, an administrator could write a configuration script that specified the warning thresholds for each major component of a system and also specified a set of actions that the administrator wants each system to take in case of a warning or failure event.
Command level 1 is omreport, command level 2 is about, and the name=value pair is details=true. Many commands use command level 1, command level 2, and command level 3, but do not require any parameters (name=value pairs). Most omreport commands are of this type. For example: omreport system alertaction causes a list of alert actions that are configured for components on your system to be displayed. The most complex commands have all three command levels and can have multiple name=value pairs.
omhelp: Getting Help With CLI Commands The omhelp command and its equivalent, -?, accesses the CLI's detailed help text interface. You can get help at several levels of detail. Each fully qualified CLI command may have a variable number of distinct parts: the command (command level 1), one or more subcommands (command level 2 and command level 3, if present), and one or more name=value pair(s). By appending -? (space-dash-question mark) to any command, you can get help on the command.
Figure 2-1. Different Levels of Help for a Command You can also parse the omconfig system assetinfo command as follows: [name=value pair 2] where command levels 1, 2, and 3 are represented by omconfig system assetinfo, name=value pair 1 is represented by info=depreciation, and name=value pair 2 is represented by method=straightline.
omreport: Viewing System Status Using the Instrumentation Service The omreport command allows you to see detailed information about your system components. You can retrieve summaries for many system components at one time, or you can get details about a specific component. This chapter shows you how to get reports with the level of detail that you want. Commands documented in this chapter vary in whether they define the fields that appear in the results of a particular omreport command.
Table 3-1 is a high-level summary of the omreport command. The column titled "Command level 1" shows the omreport command at its most general. "Command level 2" shows the major objects or components that you can view using omreport (about, chassis, storage, system, and rac). "Command level 3" lists the specific objects and components for which you can view reports. "User privilege required" refers to the type of privilege you need to perform the command, where U=User, P=Power User, and A=Administrator.
Table 3-1. Command level 1 omreport Command Level 1, Level 2, and Level 3 (continued) Command Command level 2 level 3 User privilege required Use frontpanel U, P, A Shows whether the front panel button settings, such as for the Power button and/or Nonmasking Interrupt (NMI) button (if present on the system), are enabled or disabled. fru U, P, A Shows the Field Replaceable Unit (FRU) information. info U, P, A Shows a status summary for main system chassis components.
Table 3-1. Command level 1 omreport Command Level 1, Level 2, and Level 3 (continued) Command Command level 2 level 3 rac 24 User privilege required Use alertaction U, P, A Shows warning and failure threshold values, as well as actions that have been configured when an essential component detects a warning or failure state. alertlog U, P, A Allows the administrator to show the alert log. assetinfo U, P, A Shows cost of ownership information for your system.
Help With the omreport Command Use the omreport -? command to get a list of the available commands for omreport. Use omreport -? to get help on the level 2 commands about, chassis, and system. The following information on omreport system -? applies equally to getting help for the omreport chassis command.
omreport chassis Commands Use omreport chassis commands to view details for the entire chassis or for a particular component. omreport chassis When you type: omreport chassis Server Administrator displays a general status for your main system chassis components. NOTE: When you issue CLI commands to a server module in a modular system, chassis refers only to the server module.
AC Power Lines Status : Ok Location : AC Power Line 1 AC Present : Power Present Active Source : Active Status : Ok Location : AC Power Line 2 AC Present : Power Present Active Source : Not Active Server Administrator reports values for the Redundancy Status and Redundancy Mode fields. omreport chassis batteries Use the omreport chassis batteries command to view battery properties. omreport chassis bios Use the omreport chassis bios command to view current BIOS information.
Table 3-2. BIOS Setup Parameters Parameters Description Bezel Displays whether the bezel removal intrusion check during system reboot is enabled or disabled. Bootsequence Displays the device that is used to boot the system. Console Redirection Displays if the BIOS screen is redirected over a particular serial port or if it is turned off. Console Redirection After Boot Displays whether console redirection after system reboot is enabled or disabled.
Table 3-2. BIOS Setup Parameters (continued) Parameters Description RAID Channel A Displays whether RAID-on-motherboard Channel A is detected as a RAID device or a SCSI device. RAID Channel B Displays whether RAID-on-motherboard Channel B is detected as a RAID device or a SCSI device. SATA Displays whether the onboard SATA controller is set to ATA mode, RAID mode, or is disabled. SATA port Displays if the SATA port is enabled or disabled.
Table 3-3. omreport chassis bmc name=value pair Description config=advsol Reports advanced BMC information on a serial over local area network (LAN) connection. config=nic Reports BMC information for the LAN. config=serial Reports serial port information for BMC. config=serialoverlan Reports BMC information on a serial over LAN connection. config=terminalmode Reports terminal mode settings for the serial port. config=user Reports information on BMC users.
omreport chassis firmware Use the omreport chassis firmware command to view current firmware properties. When you type: omreport chassis firmware Server Administrator displays a summary of your system’s firmware properties. omreport chassis frontpanel Use the omreport chassis frontpanel command to view whether the front panel button control settings, such as for the Power button and/or Nonmasking Interrupt (NMI) button (if present on the system), are enabled or disabled.
Depending on your configuration, output may resemble the following example: Index : 0 Chassis Name : Main System Chassis Host Name : everglades Baseboard Management Controller Version : 1.80 Primary Backplane Version : 1.01 Sensor Data Record Version : SDR Version 0.
omreport chassis leds Use the omreport chassis leds command to find out whether clear hard drive fault is supported and what severity level lights up the LED. Type: omreport chassis leds index=n The index parameter is optional. If you do not specify the index, Server Administrator displays a summary of LED information for chassis 0. If you specify the index, Server Administrator displays a summary for a specific chassis.
If your system supports redundant memory, the redundancy output may resemble the following: Memory Redundancy Redundancy Status Fail Over State Redundancy Configuration Attributes Memory Array 1 Attributes Memory Array 1 Attributes Memory Array 1 Attributes Memory Array 1 Attributes Memory Array 1 : : : : : : : : : : : : : Full Inactive SpareBank Location Proprietary Add-on Card Use Unknown Installed Capacity 1536 MB Maximum Capacity 12288 MB Slots Available 12 omreport chassis nics Use the omreport chas
Connector Type refers to the type of plug or cable and plug that connects two devices together, in this case, the type of connector that attaches an external device to a system. There are many connector types, each designed to connect a different device type to a system. Examples include DB-9 Male, AT, Access Bus, PS/2, and so on. Maximum Speed is the port speed. Port speed refers to the data transmission rate of an input/output channel, measured in numbers of bits per second.
For AMD™ Processor • 64-bit Support • AMD-V™ • AMD PowerNow!™ • No Execute (NX) The following fields are defined for a cache present on a particular microprocessor. If the cache is internal to the processor, the fields do not appear in the cache report: • Speed • Cache Device Supported Type • Cache Device Current Type • External Socket Name Fields Reported for Each Cache on a Particular Processor Status reports whether a specific cache on the processor is enabled or disabled.
• A 2-way set-associative cache directly maps two specific lines of memory to the same two lines of cache. • A 1-way set-associative cache directly maps a specific line of memory in the same line of cache. For example, line 0 of any page in memory must be stored in line 0 of cache memory. Cache Device Supported Type is the type of static random access memory (SRAM) that the device can support. Cache Device Current Type is the type of the currently installed SRAM that the cache is supporting.
Table 3-5. omreport chassis remoteaccess name=value pair Description config=advsol Reports advanced BMC or RAC information on a serial over local area network (LAN) connection. config=nic Reports BMC or RAC information for the LAN. config=serial Reports serial port information for BMC or RAC. config=serialoverlan Reports BMC or RAC information on a serial over LAN connection. config=terminalmode Reports terminal mode settings for the serial port.
omreport chassis volts Use the omreport chassis volts command to view properties of your system’s voltage probes. When you type: omreport chassis volts index=n The index parameter is optional. If you do not specify the index, Server Administrator displays a summary of status, readings, and thresholds set for any voltage probes that might be present on your system. If you specify the index, Server Administrator displays a summary for a specific voltage probe.
To view the contents of the alert log, type: omreport system alertlog To view the contents of the command log, type: omreport system cmdlog To view the contents of the ESM log, type: omreport system esmlog ESM Log Overall Health Status When you type omreport system esmlog, the Embedded Systems Management (ESM) report displays. The first line of the report reflects the overall health of the system hardware.
• power supply warning • power supply failure • degraded redundancy • lost redundancy • temperature warning • temperature failure • voltage warning • voltage failure • processor warning • processor failure • hardware log warning • hardware log full • watchdog ASR omreport system assetinfo Use the omreport system assetinfo command to see cost of ownership data for the system, such as acquisition, depreciation, and warranty information.
--------------Power Supplies ---------------Settings Enable: Informational, Warning and Critical Disable: None ----------Fans ----------Settings Enable: Critical Disable: Informational and Warning The full report lists the settings for all components in your system for which events can be generated. To view the status for components of a specific type, use the omreport system events type= command.
Example Command for Event Type When you type: omreport system events type=fans The following is an example output: ----------Fans ----------Settings Enable: Critical Disable: Informational and Warning omreport system operatingsystem Use the omreport system operatingsystem command to display operating system information. omreport system pedestinations Use the omreport system pedestinations command to view destinations where alerts for platform events are configured to be sent.
Table 3-7. omreport system pedestinations (continued) Output Attributes Description Destination Number: Destination 3 destination 3: Displays the third Destination IP Address: 201.202.203.204 destination. 201:202:203:204: IP address of the third destination. Destination Number: Destination 4 destination 4: Displays the fourth Destination IP Address: 210.211.212.213 destination. 210.211.212.213: IP address of the fourth destination.
Example Command Output When you type: omreport system summary the output that appears in your CLI window depends on the systems management software, operating system, and hardware components and options that are installed on your system.
The system summary hardware information includes data values for installed components of the following types that are present in your system: System Attributes • Host name • System location Main System Chassis Chassis • Chassis model • Chassis service tag • Chassis lock • Chassis asset tag If you run this command on a PowerEdge 1655MC system, the following additional information displays: • Server Module Service Tag — The service tag of the server module that you are currently logged into.
Memory Array The following details are listed for each memory board or module in the system (for example, the system board or the memory module in a given slot number): • Location • Use • Installed capacity • Maximum capacity • Slots available • Slots used • ECC type BIOS • Manufacturer • BIOS version • Release date • BIOS firmware information • Name • BIOS firmware version Firmware • Name • Version Network Interface Card The following details are listed for each NIC in the
omreport system thrmshutdown Use the omreport system thrmshutdown command to view which properties, if any, have been configured for a thermal shutdown action. The three properties that display for thermal shutdown are disabled, warning, or failure.
--------------Software --------------Name : Microsoft Windows Server 2003, Enterprise Edition Version : 5.2 Updateable : N/A Name : Dell Server Administrator Version : 5.1.
omreport: Viewing System Status Using the Instrumentation Service
omconfig: Managing Components Using the Instrumentation Service The omconfig command allows you to provide values that define warning events, configure alert actions, clear logs, and configure system shutdown, as well as allowing you to perform other systems management tasks.
Table 4-1 is a high-level summary of the omconfig command. The columns titled "Command level 2" and "Command level 3" list the major arguments that can be used with omconfig. "User privilege required" refers to the type of privilege you need to perform the command, where U=User, P=Power User, and A=Administrator. "Use" is a very general statement about the actions that can be performed using omconfig. More details about syntax and use of the command appear later in this section. Table 4-1.
Table 4-1. Command level 1 omconfig Command Level 1, Level 2, and Level 3 (continued) Command level 2 Command level 3 User privilege Use required platformevents A Determines the shutdown action, if any, to be taken for a specific platform event. Also, enables and disables platform events filter alert generation. recovery P, A Determines in advance how your system responds to a hung operating system. shutdown A Allows the administrator to select from several options when shutting down the system.
Table 4-1. Command level 1 omconfig Command Level 1, Level 2, and Level 3 (continued) Command level 2 Command level 3 User privilege Use required memorymode A Enables or disables the spare bank and mirroring memory modes, and also specify which mode to use. remoteaccess A Configures remote access information. temps P, A Sets warning threshold values by default or value. NOTE: You cannot change threshold values on ESM3 and PowerEdge x8xx systems.
To scroll command output one screen at a time, type: omconfig system alertaction -? | more where | more allows you to press the spacebar to see the next screen of CLI help output. To make a file that contains all of the help for the omconfig system alertaction -? command, type: omconfig system alertaction -? -outa alert.txt where -outa directs the output of the command to a file called alert.txt.
omconfig chassis Use the omconfig chassis commands to default or to set values for current, fan, voltage, and temperature probes, to configure BIOS behavior during system start up, to clear memory error counts, and to enable or disable power button control features where system configuration permits. Use the omconfig chassis -? command to see a list of all omconfig chassis commands. NOTE: When you issue CLI commands to a server module in a modular system, chassis refers only to the server module.
Table 4-2. BIOS Setup (continued) name=value pair 1 attribute= name=value pair 2 setting= Description attribute=crab setting=enable | disable enable: Enable BIOS console redirection after system reboot. disable: Disable BIOS console redirection. NOTE: The command crab is valid for Dell PowerEdge x9xx systems only. attribute=cpuht setting=enable | disable enable: Enable logical processor hyper threading. disable: Disable logical processor hyper threading.
Table 4-2. BIOS Setup (continued) name=value pair 1 attribute= name=value pair 2 setting= Description attribute=ide setting=on | off force=true on: Enables this device. off: Disables this device. force=true: Verification of setting change. attribute=idepridrv setting=off | auto off: Disables the device. auto: Automatically detect and enable the device. attribute=intrusion setting=enable | disable enable: Enables the intrusion check during system boot.
Table 4-2. BIOS Setup (continued) name=value pair 1 attribute= name=value pair 2 setting= Description attribute=ppmode setting=at | ps2 | ecp | epp at: Set the parallel port mode to type AT. ps2: Set the parallel port mode to type PS/2. ecp: Set the parallel port mode to type ECP (extended capabilities port). epp: Set the parallel port mode to type EPP (enhanced parallel port).
Table 4-2. BIOS Setup (continued) name=value pair 1 attribute= name=value pair 2 setting= Description attribute=secondaryscsi setting=on | off on: Enables this device. off: Disables this device. attribute=serialcom setting=off | on |com1 |com2 off: Disables serial communication setting. on: Enables serial communication setting without console redirection. com1: Enables serial communication setting with console redirection via COM 1.
Table 4-2. BIOS Setup (continued) name=value pair 1 attribute= name=value pair 2 setting= Description attribute=usb setting=enabled | disabled enabled: Enables the USB port(s). disabled: Disables the USB port(s). NOTE: Depending on your system’s hardware, only one of the two attributes usb and usbb is available for configuring the USB port(s). attribute=usbb setting=enabled | enabledwithbios| disabled enabled: Enables the USB port(s) during system boot, without BIOS support.
The output from the omconfig chassis bmc command lists each of the available configurations. Table 4-3 shows the valid parameters: Table 4-3. omconfig chassis bmc name=value pair 1 config= name=value pair 2 Description config=advsol characcuminterval=number number: Sets the character accumulate interval in 5 millisecond intervals. charsendthreshold=number number: Sets the number of characters.
Table 4-3. omconfig chassis bmc (continued) name=value pair 1 config= name=value pair 2 Description config=nic (continued) nicselection=nic1 | teamednic1nic2 | dracnic nic1: Enables NIC 1. teamednic1nic2: Enables NIC teaming functionality. dracnic: Enables DRAC NIC if DRAC 5 is installed. NOTE: The option nicselection is supported only on PowerEdge x9xx systems.
Table 4-3. omconfig chassis bmc (continued) name=value pair 1 config= name=value pair 2 Description config=serial baudrate=9600 | 19200 | 38400 |57600 9600: Sets connection speed to 9600 bits per | 115200 second. 19200:Sets connection speed to 19200 bits per second. 38400: Sets connection speed to 38400 bits per second. 57600: Sets connection speed to 57600 bits per second. 115200: Sets connection speed to 115200 bits per second.
Table 4-3. omconfig chassis bmc (continued) name=value pair 1 config= name=value pair 2 Description config=serial (continued) mode=directbasic | directterminal | directbasic: Type of messaging used for IPMI directbasicterminal | modembasic | messaging over a serial connection. modemterminal | modembasicterminal directterminal: Type of messaging that uses printable ASCII characters and allows a limited number of text commands over a serial connection.
Table 4-3. omconfig chassis bmc (continued) name=value pair 1 config= name=value pair 2 Description config=serialoverlan enable=true | false true: Enables serial over LAN for the BMC. false: Disables serial over LAN for the BMC. baudrate=9600 | 19200 | 38400 | 57600 | 115200 9600: Sets the volatile and nonvolatile connection speed to 9600 bits per second. 19200: Sets the volatile and nonvolatile connection speed to 19200 bits per second.
Table 4-3. omconfig chassis bmc (continued) name=value pair 1 config= name=value pair 2 Description config=terminalmode deletecontrol=outputdel | outputbkspspbksp outputdel: BMC outputs a character when or is received. outputbkspspbksp: BMC outputs a character when or is received. echocontrol=enabled | disabled enabled: Enables characters to be sent to the screen. disabled: Disables characters to be sent to the screen.
Table 4-3. omconfig chassis bmc (continued) name=value pair 1 config= name=value pair 2 Description config=user id=number enable=true | false id=number: ID number of the user being configured. enable=true: Enables user. enable=false: Disables user. id=numberenableserialoverlan=true | false id=number: ID number of the user being configured. enableserialoverlan=true: Enables serialoverlan. enableserialoverlan=false: Disables serialoverlan.
Table 4-3. omconfig chassis bmc (continued) name=value pair 1 config= name=value pair 2 Description config=user (continued) id=user id id=user id: User ID of the user being configured. NOTE: Only RAC groups can be configured. The option dracusergroup is available only if DRAC 5 is present on the system. dracusergroup=admin | poweruser | guest | testalert | custom | none dracusergroup=admin: Enables the Administrator User privileges. dracusergroup=poweruser: Enables the Power User privileges.
Table 4-4.
Default Minimum and Maximum Warning Thresholds If you want to set both the upper and lower current warning threshold values to the recommended default value, type: omconfig chassis currents index=0 warnthresh=default You cannot default one value and set another. In other words, if you default the minimum warning threshold value, you are also selecting the default value for the maximum warning threshold value.
You cannot default one value and set another. In other words, if you default the minimum warning threshold value, you are also selecting the default value for the maximum warning threshold value. Specify a Value for Minimum and Maximum Warning Thresholds NOTE: Minimum and maximum warning thresholds for the fan probe cannot be set on PowerEdge x8xx and x9xx systems.
Table 4-8. omconfig chassis frontpanel name=value pair 1 name=value pair 2 Description lcdindex= NA Specify the LCD line number. config=none | default NA | custom none: Set the LCD text to none. default: Set the LCD text to default. custom: Set the LCD text to custom. text= NA Set the custom text for LCD when config=custom. nmibutton enable=true | false true: Enables the NMI button on the system. false: Disables the NMI button on the system.
As with other commands, the CLI issues an error message if you do not have a chassis 2 (the main chassis=0). The CLI allows you to issue commands only for the system configuration you have. omconfig chassis leds Use the omconfig chassis leds command to specify when to flash a chassis fault LED or chassis identification LED and allow you to clear the LED for the system's hard drive. Table 4-10 shows the valid parameters for the command. Table 4-10.
Table 4-11. omconfig chassis memorymode name=value pair 1 Description index= Number of the chassis where the memory module resides (the default is chassis 0, the main system chassis). redundancy=spare | Spare disables the memory module that has a correctable memory event and copies the mirror | disabled | raid5 failing module’s data to a spare bank. Disabled indicates that the system is not to use other available memory modules if uncorrectable memory events are detected.
The output from the omconfig chassis remoteaccess command lists each of the available configurations. Table 4-3 shows the valid parameters: Table 4-12. omconfig chassis remoteaccess name=value pair 1 config= name=value pair 2 Description config=advsol characcuminterval=number number: Sets the character accumulate interval in 5 millisecond intervals. charsendthreshold=number number: Sets the number of characters.
Table 4-12. omconfig chassis remoteaccess (continued) name=value pair 1 config= name=value pair 2 Description config=nic (continued) ipsource=static | dhcp | systemsoftware static: Static if the IP address of the BMC LAN interface is a fixed, assigned IP address. dhcp: DHCP if the source of the IP address of the BMC LAN interface is the dynamic host configuration protocol. systemsoftware: System software if the source of the IP address of the BMC LAN interface is from the system software.
Table 4-12. omconfig chassis remoteaccess (continued) name=value pair 1 config= name=value pair 2 Description config=nic (continued) vlanenable=true | false true: Enables the virtual LAN identification. config=serial false: Disables the virtual LAN identification. vlanid=number number: Virtual LAN identification in the range of 1 to 4094. vlanpriority=number number: Priority of virtual LAN identification in the range of 0 to 7.
Table 4-12. omconfig chassis remoteaccess (continued) name=value pair 1 config= name=value pair 2 Description config=serial (continued) mode=directbasic | directterminal | directbasic: Type of messaging used for IPMI directbasicterminal | modembasic | messaging over a serial connection. modemterminal | modembasicterminal directterminal: Type of messaging that uses printable ASCII characters and that allows a limited number of text commands over a serial connection.
Table 4-12. omconfig chassis remoteaccess (continued) name=value pair 1 config= name=value pair 2 Description config=serialoverlan enable=true | false true: Enables serial over LAN for the BMC. false: Disables serial over LAN for the BMC. baudrate=9600 | 19200 | 38400 | 57600 9600: Sets the volatile and nonvolatile | 115200 connection speed to 9600 bits per second. 19200: Sets the volatile and nonvolatile connection speed to 19200 bits per second.
Table 4-12. omconfig chassis remoteaccess (continued) name=value pair 1 config= name=value pair 2 Description config=terminalmode (continued) echocontrol=enabled | disabled enabled: Enables characters to be sent to the screen. disabled: Disables characters to be sent to the screen. handshakingcontrol=enabled | disabled enabled: Directs the BMC to output a character sequence that indicates when its input buffer is ready to accept another command.
Table 4-12. omconfig chassis remoteaccess (continued) name=value pair 1 config= name=value pair 2 Description config=user id=number enable=true | false id=number: ID number of the user being configured. enable=true: Enables user. enable=false: Disables user. id=numberenableserialoverlan=true | false id=number: ID number of the user being configured. enableserialoverlan=true: Enables serial over LAN. enableserialoverlan=false: Disables serial over LAN.
Table 4-12. omconfig chassis remoteaccess (continued) name=value pair 1 config= name=value pair 2 Description config=user (continued) id=number lanaccesslevel= administrator | operator | user| none id=number: ID number of the user being configured. lanaccesslevel=administrator: User with an ID has access privileges of an Administrator for the LAN channel. lanaccesslevel=operator: User with an ID has access privileges of an Operator for the LAN channel.
Table 4-13. omconfig chassis remoteaccess config=user id= dracusergroup=custom name=value pair 1 name=value pair 2 name=value pair 3 Description config=user (continued) id=user id logindrac= true | false true/false: Enables/disables logging into DRAC. dracusergroup=custom configuredrac= true | false true/false: Enables/disables configuration of DRAC. configure users= true | false true/false: Enables/disables configuration of users.
Default Minimum and Maximum Warning Thresholds NOTE: The capabilities for managing sensors vary by systems. If you want to set both the upper and lower temperature warning threshold values to the recommended default value, type: omconfig chassis temps index=0 warnthresh=default You cannot default one value and set another. In other words, if you default the minimum warning threshold value, you are also selecting the default value for the maximum warning threshold value.
Default Minimum and Maximum Warning Thresholds NOTE: Systems that contain ESM3 capabilities do not allow you to set warning threshold values to default values. If you want to set both the upper and lower voltage warning threshold values to the recommended default value, type: omconfig chassis volts index=2 warnthresh=default You cannot default one value and set another.
Therefore, for a computer named "myOmsa" running Server Administrator, the default name would be "myOmsa–omsa". This is the name of Server Administrator defined in Active Directory by using the snap–in tool. This name must match the name for the application object in Active Directory in order to find user privileges. NOTE: This command is applicable only on systems running the Windows operating system. Table 4-16 shows the valid parameters for the command. Table 4-16.
Table 4-17. SNMP Root Password Parameters name=value pair Description setting=rootpw Required. oldpw= Enter the old SNMP root password. newpw= Sets the new SNMP root password. confirmnewpw= Confirms the new SNMP root password. When you type omconfig preferences snmp setting=rootpw, the system prompts you to supply values for the required parameters. When you type omconfig preferences snmp, you must supply all of the parameters in the initial command line.
Table 4-19. Enabling User Access for Administrators, Power Users, and Users Command Result Description omconfig preferences useraccess enable=user Grants Server Least restrictive form Administrator access of user access. to Users, Power Users, and Administrators. omconfig preferences useraccess enable=poweruser Grants Server Administrator access to Power Users and Administrators. omconfig preferences useraccess enable=admin Grants Server Most restrictive form Administrator access of user access.
Available Alert Actions Table 4-20 shows the alert actions for each component that allows you to configure an alert action . Table 4-20. Alert Actions You Can Set for Warning and Failure Events Alert Action Setting Description alert=true | false true: Enables your system's console alert. When enabled, the monitor attached to the system from which you are running Server Administrator displays a visual alert message. false: Disables your system's console alert.
Table 4-21. Events for Which You Can Set Alert Actions (continued) Event Name Description event=powersupplywarn Sets actions when a power supply probe detects a warning value. event=processorwarn Sets actions when a processor probe detects a warning value. event=processorfail Sets actions when a processor probe detects a failure value. event=redundegrad Sets actions when a redundant component becomes inoperative, resulting in less than full redundancy for that component.
Commands for Clearing Logs NOTE: For more information about alert messages, see the Dell OpenManage™ Server Administrator Messages Reference Guide. You can use the omconfig system command to clear three logs: the alert log, the command log, and the hardware, or ESM, log. To clear the contents of the alert log, type: omconfig system alertlog action=clear NOTE: Entering an invalid RAC user name may prevent the command log from displaying. Clearing the command log resolves this condition.
omconfig system platformevents Use the omconfig system platformevents command to configure shutdown action, if any, to be taken for a specific platform event. You can also enable or disable platform event filter alert generation. NOTICE: If you set a platform event shutdown action to anything other than "none", your system will forcefully shutdown when the specified event occurs.
Table 4-24. 94 omconfig system platformevents (continued) Event Name Description event=fanfail Sets action or enables/disables alert generation when a fan probe detects that the fan is running too slow or not at all. event=hardwarelogfail Enables/disables alert generation when a hardware log detects a failure value. event=intrusion Sets action or enables/disables alert generation when a chassis has been opened.
omconfig system events Use the omconfig system events command to enable and disable SNMP traps for components on your system. NOTE: Not all event types may be present on your system. There are four parameters in the name=value pair component of the omconfig system events command: • source • type • severity • index Source At present, source=snmptraps is a required name=value pair because SNMP is currently the only supported source of event notification for your system’s components.
Severity In the context of configuring events, severity determines how severe an event must be before Server Administrator notifies you of the event for a component type. When there are multiple components of the same type in the same system chassis, you can also specify whether you want to be notified for event severity according to the number of the component by using the index= parameter. Table 4-26 shows the valid severity parameters. Table 4-26.
omconfig system recovery Use the omconfig system recovery command to set the action that is to be taken when the operating system has hung or crashed. You can also set the number of seconds that must pass before the system is considered to have a hung operating system. Table 4-28 shows the valid parameters for the command. NOTE: Upper and lower limits for the timer are dependent on your system model and configuration. Table 4-28.
Table 4-29. Shutdown Parameters name=value pair Description action=reboot Shuts down the operating system and initiates system startup, performing BIOS checks and reloading the operating system. action=poweroff Turns the electrical power to the system off. action=powercycle Turns the electrical power to the system off, pauses, turns the power on, and reboots the system. Power cycling is useful when you want to reinitialize system components such as hard drives.
Example Thermal Shutdown Commands To trigger a thermal shutdown when a temperature probe detects a failure event, type: omconfig system thrmshutdown severity=failure To disable thermal shutdown so that an administrator has to initiate an omconfig system shutdown, type: omconfig system thrmshutdown severity=disabled omconfig: Managing Components Using the Instrumentation Service 99
omconfig: Managing Components Using the Instrumentation Service
omconfig system assetinfo: Editing Cost of Ownership Values omconfig System Asset Info Overview The omconfig system assetinfo command helps you to edit a comprehensive set of parameters that make up your system's total cost of ownership. This section explains the parameters that can be reported and configured under the omconfig system assetinfo command. Using the omconfig system assetinfo command, you can set governing values for configurable objects.
Table 5-1. omconfig system assetinfo info=acquisition (continued) Command Command Command name=value pair 1 name=value pair 2 level 1 level 2 level 3 Use expensed=yes | no Whether the system is charged to a specific purpose or department such as research and development or sales. installdate= Date the system was put into service. ponum= Number of the document that authorized payment for the system. purchasecost= Price the owner paid for the system.
Adding Depreciation Information Depreciation is a set of methods for computing the devaluation of your asset over time. For example, the depreciation of a system that is expected to have a useful life of 5 years would be 20 percent. Use the omconfig system assetinfo=depreciation command to add details about how your system's depreciation is to be computed. Table 5-2 shows the valid parameters for the command. Table 5-2.
Adding Extended Warranty Information Use the omconfig system extwarranty command to assign values for extended warranty information. A warranty is a contract between the manufacturer or dealer and the purchaser of a system. The warranty identifies the components that are covered for repair or replacement for a specified length of time or usage. The extended warranty comes into force after the original warranty expires. For details on how to edit warranty values, see "Adding Warranty Information.
Adding Lease Information A lease is an agreement to pay for the use of a system for a specified period of time. The lessor retains ownership of the system. Table 5-4 shows the valid parameters for the command. Table 5-4. omconfig system assetinfo info=lease Command Command Command name=value pair 1 name=value pair 2 level 1 level 2 level 3 Use omconfig system assetinfo info=lease buyout= Amount of money paid to purchase a system from a lessor.
Adding Maintenance Information Maintenance refers to activities required to keep the system in good working order. Table 5-5 shows the valid parameters for adding maintenance information. Table 5-5. omconfig system assetinfo info=maintenance Command Command Command name=value pair 1 level 1 level 2 level 3 name=value pair 2 Use enddate= Date the extended warranty agreement ends. provider= Business entity providing the maintenance service.
Adding Outsource Information Outsourcing is the practice of contracting with another business to maintain the system in good working order. Table 5-6 shows the valid parameters for adding outsource information. Table 5-6. omconfig system assetinfo info=outsource Command Command Command name=value pair 1 name=value pair 2 level 1 level 2 level 3 Use omconfig system assetinfo info=outsource levels= Levels of service offered by the provider.
Adding Owner Information The owner is the party that holds legal property title to the system. Table 5-7 shows the valid parameters for adding owner information. Table 5-7. omconfig system assetinfo info=owner Command Command Command name=value pair 1 name=value pair 2 level 1 level 2 level 3 Use omconfig system assetinfo info=owner insuranceco= Name of the insurance company that insures the system. ownername= Business entity that owns the system.
Adding Service Contract Information A service contract is an agreement that specifies fees for preventive maintenance and repair of the system. Table 5-8 shows the valid parameters for adding contract information. Table 5-8. omconfig system assetinfo info=service Command Command Command name=value pair 1 name=value pair 2 level 1 level 2 level 3 Use omconfig system assetinfo info=service renewed=true | false Whether the service agreement has been renewed.
Adding Support Information Support refers to technical assistance that the system user can seek when the user desires guidance on the proper use of a system to perform tasks. Table 5-9 shows the valid parameters for adding support information. Table 5-9. omconfig system assetinfo info=support Command Command Command name=value pair 1 name=value pair 2 Use level 1 level 2 level 3 omconfig system assetinfo info=support automaticfix= Name of any application used to fix a problem automatically.
Adding System Information System information includes the primary user of the system, the phone number for the primary user, and the system location. Table 5-10 shows the valid parameters for adding system information. Table 5-10. omconfig system assetinfo info=system Command Command Command level 1 level 2 level 3 name=value pair 1 name=value pair 2 Use location= Location of the system. primaryphone= Phone number of the system's primary user.
Adding Warranty Information Use the omconfig system warranty command to assign values for warranty information. A warranty is a contract between the manufacturer or dealer and the purchaser of a system. The warranty identifies the components that are covered for repair or replacement for a specified length of time or usage. For details on how to edit extended warranty values, see "Adding Extended Warranty Information." Table 5-11 shows the valid parameters for adding warranty information. Table 5-11.
omreport rac: Viewing Remote Access Controller Components The remote access controller (RAC) is a system component that provides a full set of system management capabilities. Server Administrator integrates the RAC features into its interface, allowing users to view and manage the controller from within Dell™ OpenManage™ Server Administrator and Dell OpenManage IT Assistant. NOTE: Some features documented may not be available on your system's RAC.
Table 6-1. Command level 1 omreport rac Command Level 1, Level 2, and Level 3 Command level 2 Command level 3 User privilege required Use omreport rac authentication U, P, A Enables or disables user access to the RAC based on how the Administrator has set up each user’s local operating system user account privileges. dialinusers U, P, A Displays the dial-in user properties. dialoutusers U, P, A Displays the dial-out user properties. network U, P, A Displays the onboard NIC properties.
Example Command for omreport rac authentication When you type: omreport rac authentication the results that display show whether authentication of users for access to the RAC using the operating system user access definitions is disabled or enabled. For example: omreport rac authentication localauthenable=true omreport rac dialinusers Use the omreport rac dialinusers command to display the dial-in user property values. Table 6-2 displays the valid parameters for the command. Table 6-2.
omreport rac network Use the omreport rac network command to display the NIC property values. omreport rac modem Use the omreport rac modem command to display the onboard modem property values. omreport rac remote Use the omreport rac remote command to display the remote features property values. omreport rac snmptraps Use the omreport rac snmptraps command to display the SNMP trap property values. Table 6-4 displays the valid parameters for the command. Table 6-4.
omreport rac viewcertificate Use the omreport rac viewcertificate command to view the server or certificate authority (CA) certificate on the RAC. The only parameter you must specify is whether the certificate you want to view is a CA certificate or a server certificate. Table 6-6 displays the valid parameters for the command. Table 6-6.
omreport rac: Viewing Remote Access Controller Components
omconfig rac: Managing the Remote Access Controller The omconfig rac command enables you to configure the operational components of the Remote Access Service (RAS). The CLI command omconfig rac uses the remote access controller (RAC) software interface to configure these operational components. NOTE: Some features documented may not be available on your system's RAC. For example, dial-up modem use is supported only on DRAC III.
Table 7-1 is a high-level summary of the omconfig rac command. The column titled "Command level 3" lists the major arguments that can be used with omconfig rac. "User privilege required" refers to the type of privilege you need to execute the command, where U=User, P=Power User, and A=Administrator. "Use" is a very general statement about the actions that can be performed using omconfig rac. More details about syntax and use of the command appear later in this section. Table 7-1.
Help With the omconfig rac Command Use the omconfig rac -? command to get a list of the available commands for omconfig rac. Use omconfig rac -? to see a list of name=value pairs that you may need to use with dialinusers, dialoutusers, modem, network, remote, and so on. Type: omconfig rac dialinusers -? The following is an excerpt of the Server Administrator response: dialinusers Set dial-in user properties.
Example Command for omconfig rac authentication When you type: omconfig rac authentication localauthenable=true you have configured the RAC to allow access to any user who has Administrator privileges on the operating system. When you type: omconfig rac authentication localauthenable=false you have configured the RAC to allow access only to users with user names and passwords that are defined by the RAC administrator.
Example Commands The following example sets one name=value pair. Type: omconfig rac dialinusers username=jdoe The next example supplies values for all command parameters that you can use with the omconfig rac dialinusers command. Type: omconfig rac dialinusers username=jdoe index=0 password=steven70 callbacknumber=4441022 callbacktype=preset The following message appears: Command Successful.
Example Commands The following example sets one name=value pair. Type: omconfig rac dialoutusers ipaddr=14.16.53.18 The following message appears: Command Successful. Please reset RAC card! The next example supplies values for all command parameters that you can use with the omconfig rac dialoutusers command. Type: omconfig rac dialoutusers ipaddr=14.16.53.18 index=1 username=sustein password=74chaunu phonenumber=4021027 authtype=any The following message appears: Command Successful.
Table 7-4. omconfig rac generatecert name=value pair Description commonname= Enter a unique text string that distinguishes your system from others for which you may be requesting certificates (required). countrycode= Two-letter code representing the country where your system is located. See ISO Standard 3166 (required). emailaddress= The e-mail address of your system. file= The absolute pathname or filename (with extension) of the CSR to be generated (required).
Table 7-6.
omconfig rac network Use the omconfig rac network command to specify network parameter values. Table 7-7 shows the valid parameters for the command. Table 7-7. omconfig rac network name=value pair Description ipaddr= Sets the IP address, which must be specified in dotted-decimal notation. subnetmask= Sets the subnet mask, which must be specified in dotted-decimal notation. gateway= Sets the gateway, which must be specified in dotted-decimal notation.
omconfig rac snmptraps Use the omconfig rac snmptraps command to specify the SNMP trap property values. Table 7-8 shows the valid parameters for the command. Table 7-8. omconfig rac snmptraps name=value pair Description ipaddr= Sets the IP address, which must be specified in dotted-decimal notation. index= Sets the SNMP trap index. The index specifies one of the 16 trap "positions" on the RAC.
omconfig rac remote Use the omconfig rac remote command to specify the remote features property values. Table 7-9 shows the valid parameters for the command. Table 7-9. omconfig rac remote name=value pair Description floppytftpenable=true | false true: Enables remote boot. false: Disables remote boot. floppytftpipaddr= Sets the floppy TFTP address. floppytftppath= Sets the floppy TFTP path. fwupdatetftpipaddr= Sets the firmware TFTP address.
Example Command The following example sets one name=value pair. Type: omconfig rac rmdialinuser username=jdoe The following message appears: Command Successful. Please reset RAC card! omconfig rac rmdialoutuser Use the omconfig rac rmdialoutuser command to remove a dial-out user. Table 7-11 shows the valid parameters for the command. Table 7-11. omconfig rac rmdialoutuser name=value pair Description username= Specifies the user name of entry which is to be deleted.
omconfig rac rmsnmptrap Use the omconfig rac rmsnmptrap command to remove an SNMP trap. Table 7-12 shows the valid parameters for the command. Table 7-12. omconfig rac rmsnmptrap name=value pair Description ipaddr= Specifies the IP address of entry which is to be deleted. This value must be specified in dotted-decimal notation. If no IP address is specified, an index must be specified. index= Specifies the index of the entry which is to be deleted.
omconfig rac reset Use the omconfig rac reset command to reset the RAC. omconfig rac uploadcert Use the omconfig rac uploadcert command to upload the server or CA certificate to the RAC. You must enter the fully qualified pathname of the certificate and select the type of certificate to upload. The two types of certificate that you can upload are a server certificate, or a certificate that you can obtain from a certificate authority (CA).
Table 7-15. omconfig rac users (continued) name=value pair Description numericpagingenable=true | false true: Enables numeric paging. false: Disables numeric paging. numericpagernumber= Sets the numeric pager number. numericpagermsg= Sets the numeric pager message. emailpagingenable=true | false true: Enables e-mail paging. false: Disables e-mail paging. emailaddress= Sets the e-mail address. emailmsg= Set the e-mail message.
omconfig rac: Managing the Remote Access Controller
Using the Storage Management Service Storage Management has a fully-featured command line interface (CLI) that enables you to perform all of Storage Management’s reporting, configuration, and management functions from an operating system command shell. The Storage Management CLI also enables you to script command sequences. The Storage Management CLI provides expanded options for the Dell™ OpenManage™ Server Administrator omreport and omconfig commands.
For example, the following omconfig command syntax for blinking a physical disk has three levels and three name=value pairs: omconfig storage pdisk action=blink controller=id pdisk= where PDISKID= In this example, the id in controller=id is the controller number such that controller 1 would be specified as controller=1. Syntax for Required, Optional, and Variable Command Elements The omreport and omconfig commands have multiple name=value pairs.
Table 8-2. Syntax For Name=Value Pairs For Parameters (continued) Syntax Description pdisk= Indicates a particular physical disk by specifying either connector:targetID or connector:enclosureID:portID. To obtain the values for the connector, enclosure, and physical disk (targetID or portID), you would enter omreport storage controller to display the controller IDs and then enter omreport storage pdisk controller=id to display the IDs for the physical disks attached to the controller.
omreport Storage Help The following table provides the omreport storage command syntax. Table 8-3. omreport storage help Command Level 1 Command Level 2 Command Level 3 Use omreport storage Displays a list of storage components for which omreport commands are available. pdisk Displays a list of the omreport storage pdisk parameters for displaying physical disk information. vdisk Displays a list of omreport storage vdisk parameters for displaying virtual disk information.
omreport Global Information (Smart Thermal Shutdown Status) Table 8-5. omreport Global Information Commands Required Command Levels (1, 2, 3) Optional name=value pairs Use omreport storage globalinfo Displays whether smart thermal shutdown is enabled or disabled. See the "omconfig Global Enable Smart Thermal Shutdown" command for more information. omreport Battery Status Table 8-6.
Table 8-7. omreport Connector Commands (continued) Required Command Levels (1, 2, 3) Optional name=value pairs controller=id where id is the controller number. For example: controller=0 Use Displays information for the specified connector on the controller. connector=id where id is the connector number. For example: connector=0 omreport Enclosure Status Table 8-8.
Table 8-9. omreport Temperature Probe Commands Required Command Levels (1, 2, 3) Optional name=value pairs and name=value pair Use controller=id enclosure= info=temps index=n Displays the specified temperature probe. where id is the controller number and the enclosure number and “n” is the number of a temperature probe. For example: controller=0 enclosure=2 info=temps index=1 omreport Fan Status Table 8-10.
omreport Power Supply Status Table 8-11. omreport Power Supply Commands Required Command Levels (1, 2, 3) Optional name=value pairs and name=value pair Use omreport storage enclosure Displays property information for all enclosures attached to the system. controller=id enclosure= info= pwrsupplies Displays the power supplies for the specified enclosure. where id is the controller number and the enclosure number.
Table 8-12. omreport EMM Commands (continued) Required Command Levels (1, 2, 3) Optional name=value pairs and name=value pair Use controller=id enclosure= info=emms index=n Displays the specified EMMs. where id is the controller number and the enclosure number and “n” is the number of an EMM. For example: controller=0 enclosure=2 info=emms index=1 omreport Physical Disk Status Table 8-13.
omreport Virtual Disk Status Table 8-14. omreport Virtual Disk Commands Required Command Levels (1, 2, 3) Optional name=value pairs Use omreport storage vdisk Displays property information for all virtual disks on all controllers. controller=id where id is the controller number. For example: controller=0. controller=id vdisk=id where id is the controller number and the virtual disk number. For example: controller=0 vdisk=1. Displays all virtual disks on the specified controller.
Example Syntax The omconfig command syntax for enabling thermal shutdown does not require that you specify a controller or enclosure ID. To enable thermal shutdown, enter the following: omconfig storage globalinfo action=enablests NOTE: You can use the omreport storage globalinfo command to determine whether smart thermal shutdown is currently enabled or disabled. The status of smart thermal shutdown is also displayed by the Server Administrator graphical user interface.
Example Syntax The omconfig command syntax for rescanning all controllers on the system does not require that you specify a controller ID. To do a global rescan of all controllers, enter the following: omconfig storage globalinfo action=globalrescan NOTE: Global rescan is not supported on non-RAID SCSI and SAS controllers. You must reboot the system before Storage Management can see configuration changes on non-RAID SCSI controllers.
Table 8-16.
omconfig Enable Controller Alarm Use the following omconfig command syntax to enable the controller alarm. See the online help for more information about using this command. Complete Syntax omconfig storage controller action=enablealarm controller=id where id is the controller ID as reported by the omreport storage controller command.
omconfig Test Controller Alarm Use the following omconfig command syntax to test the functionality of the controller alarm. The alarm will sound for about two seconds. See the online help for more information about using this command. Complete Syntax omconfig storage controller action=testalarm controller=id where id is the controller ID as reported by the omreport storage controller command.
omconfig Create Virtual Disk The online help provides additional information about creating virtual disks. The omconfig syntax for creating a virtual disk has several parameters.
controller=id Parameter (Required) Specify the controller ID as reported by the omreport storage controller command. For example: controller=2 raid= Parameter (Required) Use the raid= parameter to specify concatenation or a RAID level for a virtual disk. Different controllers support different RAID levels. See the online help for information on the RAID levels a controller supports and for general information about RAID levels and concatenation.
PDISKID= Use this parameter to specify the physical disks that will be included in the virtual disk. When reconfiguring a virtual disk, you must specify all physical disks to be included in the reconfigured virtual disk. The physical disk specification applies to physical disks that were in the original virtual disk and will continue to be in the reconfigured virtual disk and to any new physical disks being added to the reconfigured virtual disk.
Table 8-20. Read Policy Paramaters Read Policy readpolicy=ra | ara | nra | rc | nrc Parameter Specification Read ahead readpolicy=ra Adaptive read ahead readpolicy=ara No read ahead readpolicy=nra Read cache readpolicy=rc No read cache readpolicy=nrc [writepolicy=] Parameter (Optional) Different controllers support different write policies. See the online help for more information.
Example Syntax For example, you may want to create a RAID 5 virtual disk on a PERC 3/QC controller. The online help will help you understand which read, write, and cache policies are supported by this controller. In this example, you decide to create a virtual disk with the following read, write, and cache policy: • Read-ahead • Write–through caching • Cache I/O The virtual disk will be 500 MB with a stripe size of 16 KB.
Example Syntax For example, to set the background initialization rate to 50 on controller 1, enter: omconfig storage controller action=setbgirate controller=1 rate=50 omconfig Set Reconstruct Rate Use the following omconfig command syntax to set the reconstruct rate. Complete Syntax omconfig storage controller action=setreconstructrate controller=id rate=<0 to 100> where id is the controller ID as reported by the omreport storage controller command.
Complete Syntax omconfig storage controller action=exportlog controller=id where id is the controller ID as reported by the omreport storage controller command. Example Syntax For example, to export the log on controller 1, enter: omconfig storage controller action=exportlog controller=1 By default, the log file is exported to C:\WinNt or C:\Windows for Microsoft® Windows® systems (based on the Windows version used) and /var/log on all Linux systems.
Example Syntax For example, to import and recover foreign configurations on controller 1, enter: omconfig storage controller action=importrecoverforeignconfig controller=1 omconfig Clear Foreign Configuration Use the following omconfig command syntax to clear or delete all virtual disks that reside on physical disks that are newly attached to the controller.
Example Syntax For example, to start the patrol read task on controller 1, enter: omconfig storage controller action=startpatrolread controller=1 NOTE: To be able to start patrol read, the current patrol read mode should be set to "Manual." omconfig Stop Patrol Read Use the following omconfig command syntax to stop the patrol read task on the controller.
Table 8-22.
where id is the controller ID and virtual disk ID as reported by the omreport command. To obtain these values, enter omreport storage controller to display the controller IDs and then enter omreport storage vdisk controller=ID to display the IDs for the virtual disks attached to the controller.
Complete Syntax omconfig storage vdisk action=fastinit controller=id vdisk=id where id is the controller ID and virtual disk ID as reported by the omreport command. To obtain these values, you would enter omreport storage controller to display the controller IDs and then enter omreport storage vdisk controller=ID to display the IDs for the virtual disks attached to the controller.
omconfig Restore Dead Segments Use the following omconfig command syntax to recover data from a RAID 5 virtual disk that has been corrupted. This task attempts to reconstruct data from a corrupt portion of a physical disk included in a RAID 5 virtual disk. Complete Syntax omconfig storage vdisk action=restoresegments controller=id vdisk=id where id is the controller ID and virtual disk ID as reported by the omreport command.
Complete Syntax omconfig storage vdisk action=unmirror controller=id vdisk=id where id is the controller ID and virtual disk ID as reported by the omreport command. To obtain these values, enter omreport storage controller to display the controller IDs and then enter omreport storage vdisk controller=ID to display the IDs for the virtual disks attached to the controller.
omconfig Unassign Dedicated Hot Spare Use the following omconfig command syntax to unassign one or more physical disks that were previously assigned as a hot spare to a virtual disk. Complete Syntax omconfig storage vdisk action=assigndedicatedhotspare controller=id vdisk=id pdisk= assign=no where id is the controller ID and virtual disk ID. The variable specifies the physical disk.
omconfig Cancel Check Consistency Use the following omconfig command syntax to cancel a check consistency while it is in progress. Complete Syntax omconfig storage vdisk action=cancelcheckconsistency controller=id vdisk=id where id is the controller ID and virtual disk ID as reported by the omreport command.
Example Syntax For example, to resume a check consistency on virtual disk 4 on controller 1, enter: omconfig storage vdisk action=resumecheckconsistency controller=1 vdisk=4 omconfig Delete Virtual Disk Use the following omconfig command syntax to delete a virtual disk. NOTICE: Deleting a virtual disk destroys all information including file systems and volumes residing on the virtual disk. You may receive a warning message if you attempt to delete the system or boot partition.
Example Syntax For example, to reconfigure virtual disk 4 to a size of 800 MB, use RAID 5 and physical disks 0 through 3 on connector 0 of controller 1. On a SAS controller, the physical disks reside in enclosure 2.
Complete Syntax action=rename controller=id vdisk=id name= where id is the controller ID and virtual disk ID as reported by the omreport command and is the new name for the virtual disk. To obtain the values for controller ID and virtual disk ID, enter omreport storage controller to display the controller IDs and then enter omreport storage vdisk controller=ID to display the IDs for the virtual disks attached to the controller.
Complete Syntax action=blink controller=ID action=blink controller=id pdisk= where id is the controller ID. The variable specifies the physical disk. To obtain these values, enter omreport storage controller to display the controller IDs and then enter omreport storage pdisk controller=ID to display the IDs for the physical disks attached to the controller. Example Syntax In this example, you want to blink physical disk 0 on connector 0 of controller 1.
Example for SAS Controllers: To unblink the physical disk described in this example, enter: omconfig storage pdisk action=unblink controller=1 pdisk=0:2:0 omconfig Prepare to Remove Physical Disk Use the following omconfig command syntax to prepare a physical disk for removal: Complete Syntax omconfig storage pdisk action=remove controller=id pdisk= where id is the controller ID. The variable specifies the physical disk.
Example for SCSI, SATA, and ATA Controllers: To initialize the physical disk described in this example, enter: omconfig storage pdisk action=initialize controller=1 pdisk=0:3 Example for SAS Controllers: To initialize the physical disk described in this example, enter: omconfig storage pdisk action=initialize controller=1 pdisk=0:2:3 omconfig Offline Physical Disk Use the following omconfig command syntax to offline a physical disk: Complete Syntax omconfig storage pdisk action=offline controller=id pdi
Example for SCSI, SATA, and ATA Controllers: To offline the physical disk described in this example, enter: omconfig storage pdisk action=offline controller=1 pdisk=0:3 Example for SAS Controllers: To offline the physical disk described in this example, enter: omconfig storage pdisk action=offline controller=1 pdisk=0:2:3 omconfig Online Physical Disk Use the following omconfig command syntax to bring an offline physical disk back online.
To obtain these values, enter omreport storage controller to display the controller IDs and then enter omreport storage pdisk controller=ID to display the IDs for the physical disks attached to the controller. Example Syntax In this example, you want to assign physical disk 3 on connector 0 of controller 1 as a global hot spare. On a SAS controller, the physical disk resides in enclosure 2.
Example for SAS Controllers: To unassign the physical disk described in this example as a global hot spare, enter: omconfig storage pdisk action=assignglobalhotspare controller=1 pdisk=0:2:3 assign=no omconfig Rebuild Physical Disk Use the following omconfig command syntax to rebuild a failed physical disk. Rebuilding a disk may take several hours. If you need to cancel the rebuild, use the Cancel Rebuild task. For more information, see the online help.
Example Syntax In this example, you want to cancel the rebuild or physical disk 3 on connector 0 of controller 1. On a SAS controller, the physical disk resides in enclosure 2.
Complete Syntax omconfig storage pdisk action=clear controller=id pdisk= where id is the controller ID. The variable specifies the physical disk. To obtain these values, enter omreport storage controller to display the controller IDs and then enter omreport storage pdisk controller=ID to display the IDs for the physical disks attached to the controller. Example Syntax In this example, you want to clear physical disk 3 on connector 0 of controller 1.
omconfig Battery Commands The following sections provide the omconfig command syntax required to execute battery tasks. Table 8-24. omconfig Battery Commands Required Command Levels (1, 2, 3) Optional name=value pairs omconfig storage battery action=recondition controller=id battery=id action=startlearn controller=id battery=id action=delaylearn controller=id battery=id days=d hours=h omconfig Recondition Battery Use the following omconfig command to recondition a controller battery.
omconfig Delay Battery Learn Cycle Use the following omconfig command to delay the battery learn cycle for a specified period of time. The battery learn cycle can be delayed for a maximum of seven days or 168 hours. Complete Syntax omconfig storage battery action=delaylearn controller=id battery=id days=d hours=h where id is the controller ID and battery ID as reported by the omreport command.
Example Syntax For example, to rescan connector 2 on controller 1, enter: omconfig storage connector action=rescan controller=1 connector=2 omconfig Enclosure Commands The following sections provide the omconfig command syntax required to execute enclosure tasks. Table 8-26.
omconfig Enable Enclosure Alarm Use the following omconfig command syntax to enable the enclosure alarm: Complete Syntax omconfig storage enclosure action=enablealarm controller=id enclosure= where id is the controller ID. The variable specifies the enclosure.
omconfig Enable Smart Thermal Shutdown The omconfig storage enclosure action=enablests command was supported in previous releases of Storage Management. This command has been replaced by the omconfig storage globalinfo action= enablests command. When enabling smart thermal shutdown and creating CLI scripts, it is preferable to use the omconfig storage globalinfo action=enablests command. See the "omconfig Global Enable Smart Thermal Shutdown" command for more information.
Complete Syntax omconfig storage enclosure action=setassetname controller=id enclosure= assetname= where id is the controller ID. The variable specifies the enclosure. In this syntax, is a user-specified alphanumeric string.
Example for SCSI, SATA, and ATA Controllers: In this example, temperature probe 3 resides in the enclosure attached to connector 2 on controller 1. To set the temperature probe thresholds to 10 and 40° Celsius, enter: omconfig storage enclosure action=settempprobes controller=1 enclosure=2 index=3 minwarn=10 maxwarn=40 omconfig Reset Temperature Probe Thresholds Use the following omconfig command syntax to reset the minimum and maximum warning temperature thresholds back to their default values.
Example Syntax For example, you may want to specify the minimum and maximum warning thresholds for all temperature probes to 10 and 40° Celsius. Example for SAS Controllers In this example, the temperature probes reside in enclosure 3 attached to connector 2 on controller 1.
Example for SCSI, SATA, and ATA Controllers : For example, to blink the LEDs for the enclosure attached to connector 2 on controller 1, enter: omconfig storage enclosure action=blink controller=1 enclosure=2 Example for SAS Controllers : For example, to blink the LEDs for enclosure 3 attached to connector 2 on controller 1, enter: omconfig storage enclosure action=blink controller=1 enclosure=2:3 Using the Storage Management Service 185
Using the Storage Management Service
Working With CLI Command Results Server Administrator Command Line Interface (CLI) users can use command output in various ways. This section explains how to save command output to a file and how to select a format for your command results that fits different objectives. Output Options for Command Results CLI command output displays to standard output on your system in a command window, in an X-terminal, or on a screen, depending on your operating system type.
Save Command Results to a File That Can Be Overwritten Use the -outc option when you want to overwrite data that is stored in previously written files. For example, at 11:00 A.M. you capture fan probe RPM readings for fan probe 0 on your system and write the results to a file called fans.txt. You type: omreport chassis fans index=0 -outc fans.
Append Command Results to an Existing File Use the -outa option when you want to append new command results to data stored in a previously written file. For example, at 11:00 A.M. you capture fan probe RPM readings for fan probe 0 on your system and write the results to a file called fans.txt. If you want to compare these results with output for the same probe obtained four hours later, you can use the -outa command to append the new output to fans.txt. Type: omreport chassis fans index=0 -outa fans.
The available formats include: • List (lst) • Semicolon-separated values (ssv) • Table (tbl) • Raw xml (xml) • Custom delimited format (cdv) Syntax for the formatting option is: -fmt For example, type: omreport system summary -fmt tbl where -fmt tbl specifies table format. You can combine the formatting option with the option to direct output to a file. For example, type: omreport system summary -fmt tbl -outa summary.
Table (tbl) Use the tbl or table formatting option to have your data formatted in table rows and columns. To see the following example command output in table format, type: omreport system summary -fmt tbl The example output displays as follows: -----------------------------Network Interface Card 0 Data -----------------------------| | | | | ATTRIBUTE| VALUE IP Address| 143.166.152.108 Subnet Mask| 255.255.255.0 Default Gateway| 143.166.152.
The example output displays as follows: 1143.166.152.108255.255.255.0143.166.152.100-02-b3-23-d2-ca Custom Delimited Format (cdv) Use the cdv formatting option to report exported data in custom delimited format. You can specify this option with any omreport command.
Glossary ASPI The following list defines or identifies technical terms, abbreviations, and acronyms used in Dell™ user documents. ASR A Abbreviation for ampere(s). AC Advanced SCSI programming interface. Abbreviation for automatic system recovery. ASR consists of those procedures that restore the system to running all properly configured domains after one or more domains have been rendered inactive due to software or hardware failures or due to unacceptable environmental conditions.
backup boot routine A copy of a program or data file. As a precaution, you should back up your computer's hard drive on a regular basis. Before making a change to the configuration of your computer, you should back up important start-up files from your operating system. When you start your computer, it clears all memory, initializes devices, and loads the operating system.
cache CIM A fast storage area that keeps a copy of data or instructions for quicker data retrieval. For example, your computer's BIOS may cache ROM code in faster RAM. Or, a diskcache utility may reserve RAM in which to store frequently accessed information from your computer's disk drives; when a program makes a request to a disk drive for data that is in the cache, the disk-cache utility can retrieve the data from RAM faster than from the disk drive.
config.sys file CRC The config.sys file is executed when you boot your computer (before running any commands in the autoexec.bat file). This start-up file contains commands that specify which devices to install and which drivers to use. This file also contains commands that determine how the operating system uses memory and controls files. Abbreviation for cyclic redundancy code, which is a number derived from, and stored or transmitted with, a block of data in order to detect corruption.
DHCP DMI Acronym for dynamic host configuration protocol. A method of configuring a network in which IP addresses are issued by a server, rather than statically assigned to each system. Abbreviation for Desktop Management Interface. DMI enables the management of your computer system's software and hardware. DMI collects information about the system's components, such as the operating system, memory, peripherals, expansion cards, and asset tag.
DTE Abbreviation for data terminal equipment. Any device, such as a computer system, that can send data in digital form by means of a cable or communications line. The DTE is connected to the cable or communications line through a data communications equipment (DCE) device, such as a modem. To avoid a configuration conflict when installing an EISA expansion card, you must use the EISA Configuration Utility.
expanded memory FiFO A technique for accessing RAM above 1 MB. To enable expanded memory on your computer, you must use an EMM. You should configure your system to support expanded memory only if you run application programs that can use (or require) expanded memory. Abbreviation for first-in, first-out.
graphics coprocessor hot plug See coprocessor. The ability to remove and replace a redundant part while the system is being used. Also called a "hot spare." graphics mode A video mode that can be defined as x horizontal by y vertical pixels by z colors. HPFS Abbreviation for the High Performance File System option in the Windows NT and later Windows operating systems.
IHV ISA Acronym for independent hardware vendor. IHVs often develop their own MIBs for components that they manufacture. Acronym for Industry-Standard Architecture. A 16-bit expansion bus design. The expansion-card connectors in an ISA computer are also compatible with 8-bit ISA expansion cards. interlacing A technique for increasing video resolution by only updating alternate horizontal lines on the screen.
kg LPTn Abbreviation for kilogram(s), 1,000 grams. The device names for the first through third parallel printer ports on your computer are LPT1, LPT2, and LPT3. kHz Abbreviation for kilohertz, 1,000 hertz. LRA Acronym for local response agent. LAN Acronym for local area network. A LAN system is usually confined to the same building or a few nearby buildings, with all equipment linked by wiring dedicated specifically to the LAN.
MBR MIDI Abbreviation for master boot record. Abbreviation for musical instrument digital interface. MCA MIF Abbreviation for Micro Channel Architecture, which is designed for multiprocessing. MCA eliminates potential conflicts that arise when installing new peripheral devices. MCA is not compatible with either EISA or XT bus architecture, so older cards cannot be used with it. Acronym for management information format. A MIF file contains information, status, and links to component instrumentation.
mV NuBus Abbreviation for millivolt(s). Proprietary expansion bus used on Apple Macintosh personal computers. name The name of an object or variable is the exact string that identifies it in an SNMP Management Information Base (MIB) file, or in a DMI Management Information Format (MIF) file, or in a CIM Management Object File (MOF). NVRAM NDIS OEM Abbreviation for Network Driver Interface Specification. Acronym for network interface controller. Abbreviation for original equipment manufacturer.
PCI pixel Abbreviation for Peripheral Component Interconnect. A standard for local-bus implementation developed by Intel Corporation. A single point on a video display. Pixels are arranged in rows and columns to create an image. A video resolution, such as 640 x 480, is expressed as the number of pixels across by the number of pixels up and down. PCMCIA Personal Computer Memory Card International Association.
probe PXE An electronic sensor for measuring a quantity or determining system state at a particular point within a system. Server Administrator can monitor temperature, voltage, fan, memory, current and chassis intrusion probes. The probes provide a snapshot of the measured quantity (such as the temperature at a particular place and time) or state (a chassis intrusion has or has not occurred). Abbreviation for Pre-boot eXecution Environment.
read-only file ROM A read-only file is one that you are prohibited from editing or deleting. A file can have read-only status if: Acronym for read-only memory. Your computer contains some programs essential to its operation in ROM code. Unlike RAM, a ROM chip retains its contents even after you turn off your computer. Examples of code in ROM include the program that initiates your computer's boot routine and the POST. • Its read-only attribute is enabled.
SEC SKU Abbreviation for single-edge contact. Acronym for stock keeping unit. serial port SMART An I/O port used most often to connect a modem to your computer. You can usually identify a serial port on your computer by its 9-pin connector. Acronym for Self-Monitoring Analysis Reporting Technology. A technology that allows hard drives to report errors and failures to the system BIOS, which then displays an error message on the screen.
status system configuration information Refers to the health or functioning of an object. For example, a temperature probe can have the status normal if the probe is measuring acceptable temperatures. When the probe begins reading temperatures that exceed limits set by the user, it reports a critical status. Data stored in memory that tells a computer what hardware is installed and how the computer should be configured for operation. system diskette System diskette is a synonym for bootable diskette.
text editor An application program for editing text files consisting exclusively of ASCII characters. Windows Notepad is a text editor, for example. Most word processors use proprietary file formats containing binary characters, although some can read and write text files. text mode A video mode that can be defined as x columns by y rows of characters. threshold values Systems are normally equipped with various sensors that monitor temperature, voltage, current, and fan speed.
utility VGA A program used to manage system resources— memory, disk drives, or printers, for example. Abbreviation for video graphics array. VGA and SVGA are video standards for video adapters with greater resolution and color display capabilities than previous standards. To display a program at a specific resolution, you must install the appropriate video drivers and your monitor must support the resolution.
video memory VLSI Most VGA and SVGA video adapters include memory chips in addition to your computer's RAM. The amount of video memory installed primarily influences the number of colors that a program can display (with the appropriate video drivers and monitor capabilities). Abbreviation for very-large-scale integration. video mode vpp Video adapters normally support multiple text and graphics display modes.
win.ini file XMM A start-up file for the Windows operating system. When you start Windows, it consults the win.ini file to determine a variety of options for the Windows operating environment. Among other things, the win.ini file records what printer(s) and fonts are installed for Windows. The win.ini file also usually includes sections that contain optional settings for Windows application programs that are installed on the hard drive.
Glossary
Index Symbols -? omconfig, 54 omconfig chassis, 56 omconfig rac, 121 omreport, 25 omreport rac, 114 request for help, 19 alertlog clearing logs, 92 omconfig system, 19, 52 omreport system, 40 arrays memory, 23, 47 assetinfo acquisition, 41 omreport system, 41 A assign dedicated hot spare omconfig, 163 about omconfig, 55 assign global hot spare omconfig, 172 acquisition information, 101 optional parameters, 20 authentication omconfig rac, 121 omreport rac, 114 acquisition information adding, 101 ava
Index certificate authority, 124 certificate signing request, 124 change virtual disk policy omconfig, 167 chassis omconfig, 56 chassis fault LED, 74 CLI commands ?, 19 primary commands, 14 Windows command prompt, 14 cmdlog omconfig system, 92 omreport system, 40 chassis identification LED, 74 command levels 1,2, and 3 omconfig, 52 chassis information summary, 31 command levels 1,2,3 omreport, 22 check consistency omconfig, 164 command syntax overview, 17 check consistency rate omconfig, 155 c
conventions for command parameter tables, 21 core count omreport chassis processors, 35 CSR about, 124 generating parameters, 124 user access levels, 120 current speed omreport chassis processors, 35 currents omconfig chassis, 70 omreport chassis, 30 dialinusers omconfig rac, 122 omreport rac, 115 dialoutusers omconfig rac, 123 omreport rac, 115 dirservice omconfig preferences, 86 disable enclosure alarm omconfig, 180 disable smart thermal shutdown omconfig, 181 display IDs, 136-137 display reports RAC com
Index F I failure messages, 16 import foreign configuration omconfig, 156 fan status omreport, 141 fancontrol omconfig chassis, 72 omreport chassis, 30 fans omconfig chassis, 71 omreport chassis, 30 index omreport chassis slots, 38 info omconfig chassis, 73 omreport chassis, 31 initialize physical disk omconfig, 170 firmware omreport chassis, 31 initialize virtual disk omconfig, 160 format virtual disk, 166 introduction, 13 formatting CLI command output, 189 intrusion omreport chassis, 32
network omconfig rac, 127 omreport rac, 116 NIC property values, 116 nics omreport chassis, 34 NIS, 13 NMI button, 31 O offline physical disk omconfig, 171 omconfg cancel initialize virtual disk, 160 omconfig -?, 54 about, 55 assign dedicated hot spare, 163 assign global hot spare, 172 blink physical disk, 168 blink virtual disk, 159 cancel background initialize, 161 cancel check consistency, 165 cancel rebuild physical disk, 174 change virtual disk policy, 167 chassis, 56 check consistency, 164 command le
Index omconfig chassis bmc name=value pair, 62, 76 omconfig global commands, 144 omconfig chassis currents name=value pairs, 70 omconfig physical disk commands, 168 omconfig chassis fancontrol name=value pairs, parameters, 72 omconfig preferences, 86 cdvformat, 86 dirservice, 86 snmp, 87-88 useraccess, 88 omconfig chassis fans name=value pairs, parameters, 71 omconfig chassis frontpanel name=value pair, parameters, 73 omconfig chassis info name=value pair, parameters, 73 omconfig chassis leds na
omconfig rac users example command, 133 name=value pairs, parameters, 132 omconfig rac viewcertificate name=value pair, parameters, 117 omconfig storage battery, 177 connector, 178 controller, 146 enclosure, 179 globalinfo, 144 pdisk, 135, 168 vdisk, 158 omconfig system alertaction, 89 alertlog, 19, 52, 92 assetinfo, 101 cmdlog, 92 esmlog, 92 events, 95 extwarranty, 104 name=value pairs, parameters, 95 pedestinations, 92 platformevents, 93 recovery, 97 shutdown, 97 thrmshutdown, 98 webserver, 96 omconfig s
Index omreport chassis bmc name=value pairs, parameters, 30, 38 omreport chassis fancontrol name=value pairs, parameters, 30 omreport chassis ports base I/O address, 34 connector type, 35 external name, 34 IRQ level, 34 maximum speed, 35 port type, 34 omreport chassis processors cache properties, 35 connector name, 35 core count, 35 current speed, 35 external clock speed, 35 manufacturer, 35 processor family, 35 processor version, 35 state, 35 omreport chassis slots adapter, 38 data bus width, 38 inde
pedestinations omconfig system, 92 omreport system, 43 read policy parameters, 153 Physical disks in each stripe, 153 recondition battery omconfig, 177 platformevents omconfig system, 93 omreport system, 44 reconfiguring virtual disks omconfig, 166 port type omreport chassis ports, 34 ports omreport chassis, 34 prepare to remove physical disk, 170 primary CLI command omconfig, 14 omhelp, 14, 19 omreport, 14 primary CLI commands, 14 processor family omreport chassis processors, 35 rebuild physical dis
Index shutdown omconfig system, 97 omreport system, 44 shutdown action omconfig system platformevents, 93 slot ID omreport chassis slots, 38 slots omreport chassis, 38 smart thermal shutdown status, 139 snmp omconfig preferences, 87 storage management CLI, 135 successful commands, 15 unassign global hot spare omconfig, 173 summary omreport system, 44 unblink physical disk omconfig, 169 support information adding, 110 unmirror omconfig, 162 syntax overview CLI commands, 17 upload the CA certifi
viewcertificate omreport rac, 117 viewing alert actions for specific components and events, 40 viewing properties for system temperature probes, 38 viewing properties for system voltage probes, 39 viewing properties of system power supplies, 37 viewing properties of system slots, 38 voltage warning thresholds, 85 volts omconfig chassis, 85 omreport chassis, 39 W warranty adding, 112 components, 104, 112 omconfig system, 112 webserver omconfig system, 96 starting and stopping, 96 what’s new, 13 Winbind, 13
Index 226 Index
