Administrator Guide
– DIMM
– NVRAM
机柜 - 系统硬件运行状况组件
– 电源设备
– 风扇
– 温度
– 存储
– 机柜管理模块 (EMM)
使用 Dashboard Health(仪表板运行状况)选项
要使用导航面板以显示已安装的 DR Series 系统组件(或任何扩展架机柜)的当前系统状态,请完成以下操
作:
1. 单击 Dashboard(仪表板)→ Health(运行状况)。
此时将显示 Health(运行状况)页面。
2. 将鼠标悬停在 Health(运行状况)页面上的机箱前后面板视图上,以显示包含状态、名称以及 DR Series
系统磁盘驱动器和操作系统驱动器(DR4000 和 DR4100 系统)状态的对话框。
使用相同的过程显示包含电源设备和扩展架机柜后面板连接器的状态及名称的类似对话框。
3. 查看所有 DR Series 系统或扩展架组件(取决于所选的选项卡是 System(系统)还是 Enclosure(机柜))
的 System Hardware Health(系统硬件运行状况)摘要表中的状态。
要显示附加信息,请单击以展开相应摘要表中的每个组件。
注: Health(运行状况)页面提供了 DR Series 机箱前后视图(显示 DR4000 系统的机箱驱动器 (0-11)、
电源设备(PS1 和 PS2)以及操作系统内部驱动器(12 和 13))的状态(在 DR4100 系统中,操作系
统驱动器位于机箱背面)。此外,所有其他主要 DR Series 系统组件均列在 System Hardware Health
(系统硬件运行状况)表中(电源设备、风扇、温度、存储、电压、NIC(网络接口卡)、CPU、
DIMM(双列直插式内存模块)和 NVRAM)。对于安装的每个扩展架(Enclosure 1(机柜 1)或
Enclosure 2(机柜 2)),Health(运行状况)页面提供扩展架机箱前后视图(显示机箱驱动器
(0-11))的状态,并列出服务标签。机柜的 System Hardware Health(系统硬件运行状况)表列出了电
源设备、风扇、温度、存储和机柜管理模块 (EMM)。
有关系统组件和 Health(运行状况)页面的更多信息,请参阅运行状况、监测系统运行状况和使用 Dashboard
(仪表板)页面监测系统运行状况。
Understanding DR Series System NICs And Ports
The DR Series system supports the use of the following types of NICs:
• 1-Gigabit Ethernet (GbE) two-port (10-Base T); Dell recommends using CAT6a copper cabling
• 10-GbE two-port (100-Base T); Dell recommends using CAT6a copper cabling
• 10-GbE SFP+ two-port using LC fiber-optic transceivers or twin-axial cabling
The 1-GbE, 10-GbE, and 10-GbE SFP+ NICs configurations bond multiple Ethernet ports into a single interface by default:
• For the 1-GbE ports, this means that the four ports in the DR4000 system (or the six ports in the DR4100 system)
are bonded together to form one interface connection.
• For the 10-GbE and 10-GbE SFP+ ports, this means that to operate at maximum speed, only the two high-speed
Ethernet ports are bonded together to form one interface connection.
105