Owners Manual
Table Of Contents
- Dell EMC DSS8440 Installation and Service Manual
- Contents
- About this document
- DSS8440 system overview
- Technical specifications
- Chassis dimensions
- Chassis weight
- Processor specifications
- PSU specifications
- Cooling fans specifications
- System battery specifications
- Expansion card riser specifications
- GPU specifications
- Memory specifications
- Drive specifications
- Ports and connectors specifications
- Environmental specifications
- System diagnostics and indicator codes
- Initial system setup and configuration
- Pre-operating system management applications
- Options to manage the pre-operating system applications
- System Setup
- Viewing System Setup
- System Setup details
- System BIOS
- Viewing System BIOS
- System BIOS Settings details
- System Information
- Viewing System Information
- System Information details
- Memory Settings
- Viewing Memory Settings
- Memory Settings details
- Processor Settings
- Viewing Processor Settings
- Processor Settings details
- SATA Settings
- Viewing SATA Settings
- SATA Settings details
- Boot Settings
- Viewing Boot Settings
- Choosing system boot mode
- Changing boot order
- Network Settings
- Viewing Network Settings
- Network Settings screen details
- UEFI iSCSI Settings
- Viewing UEFI iSCSI Settings
- UEFI iSCSI Settings details
- Integrated Devices
- Viewing Integrated Devices
- Integrated Devices details
- Serial Communication
- Viewing Serial Communication
- Serial Communication details
- System Profile Settings
- Viewing System Profile Settings
- System Profile Settings details
- System Security
- Viewing System Security
- System Security Settings details
- Creating a system and setup password
- Using your system password to secure the system
- Deleting or changing system and setup password
- Operating with setup password enabled
- Redundant OS Control
- Viewing Redundant OS Control
- Redundant OS Control screen details
- Miscellaneous Settings
- Viewing Miscellaneous Settings
- Miscellaneous Settings details
- iDRAC Settings utility
- Device Settings
- Dell Lifecycle Controller
- Boot Manager
- PXE boot
- Installing and removing system components
- Safety instructions
- Before working inside your system
- After working inside your system
- Recommended tools
- System cover
- Front bezel
- Air shroud
- Drives
- Drive backplane
- Power supply unit
- Expansion cards and expansion card risers
- Removing a GPU
- Installing a GPU
- Removing a GPU support bracket
- Installing a GPU support bracket
- Removing the PCIe switch board
- Installing the PCIe switch board
- Removing a GPU power interposer board
- Installing a GPU power interposer board
- Removing a butterfly module and riser 3 board
- Installing the riser 3 board and butterfly module
- Nvidia Tesla T4 GPU
- Nvidia A100 GPU and NVLink bridge
- Nvidia A40 GPU and NVLink bridge
- Processor and heat sink
- System memory
- Riser 2 module
- Riser 1 module
- Network daughter card
- System board tray module
- System board and power interposer board
- Backup battery
- Power distribution board
- PSB power interposer board
- Front control module
- Fan louvers
- Cooling fans
- Fan cage
- Handle
- Slide rail installation
- Cable Routing
- Dell EMC DSS8440 cable instruction
- 3M cable Installation-Config A left
- 3M cable Installation-Config A right
- Fan cable assembly to fan bracket
- Fan cable MB-PDB assembly to MB
- Fan cable MB-PDB assembly to PDB
- Front control cable assembly control board to MB
- GPU power cable assembly GPU card to PSB
- IDC cable MB-PDB assembly to PDB
- IDC cable MB-PDB assembly to MB
- IDC cable PDB-PIB assembly to PIB
- IDC cable PIB-PDB assembly to PDB
- IDC cable Riser1-PDB assembly to PDB
- IDC cable Riser1-PDB assembly to riser board1
- IDC cable PIB-PDB assembly to PDB
- IDC cable Riser 2- PDB assembly to riser board 2
- Mini SAS HD cable assembly PERC-HDBP
- Mini SAS HD cable assembly HDBP-MB
- Power cable BP-PDB assembly to BP
- Power cable BP-PDB assembly to PDB
- Power cable assembly to PDB
- Power cable assembly to PIB
- Power cable1 assembly to Riser1
- Power cable2 Riser-PDB assembly to PDB
- Power cable2 Riser-PDB assembly to Riser
- Jumpers and connectors
- Getting help
Integrated Devices
You can use the Integrated Devices screen to view and configure the settings of all integrated devices including the video
controller, integrated RAID controller, and the USB ports.
Viewing Integrated Devices
To view the Integrated Devices screen, perform the following steps:
Steps
1. Power on, or restart your system.
2. Press F2 immediately after you see the following message:
F2 = System Setup
NOTE: If your operating system begins to load before you press F2, wait for the system to finish booting, and then
restart your system and try again.
3. On the System Setup Main Menu screen, click System BIOS.
4. On the System BIOS screen, click Integrated Devices.
Integrated Devices details
About this task
The Integrated Devices screen details are explained as follows:
Option
Description
User Accessible
USB Ports
Configures the user accessible USB ports. Selecting Only Back Ports On disables the front USB ports;
selecting All Ports Off disables all front and back USB ports.
The USB keyboard and mouse still function in certain USB ports during the boot process, depending on
the selection. After the boot process is complete, the USB ports will be enabled or disabled as per the
setting.
Internal USB Port Enables or disables the internal USB port. This option is set to On or Off. This option is set to On by
default.
iDRAC Direct
USB Port
The iDRAC Direct USB port is managed by iDRAC exclusively with no host visibility. This option is set to
ON or OFF. When set to OFF, iDRAC does not detect any USB devices installed in this managed port.
This option is set to On by default.
Integrated RAID
Controller
Enables or disables the integrated RAID controller. This option is set to Enabled by default.
Embedded NIC1
and NIC2
NOTE: The Embedded NIC1 and NIC2 options are only available on systems that do not have
Integrated Network Card 1.
Enables or disables the Embedded NIC1 and NIC2 options. If set to Disabled, the NIC may still be
available for shared network access by the embedded management controller. The embedded NIC1
and NIC2 options are only available on systems that do not have Network Daughter Cards (NDCs).
The Embedded NIC1 and NIC2 option is mutually exclusive with the Integrated Network Card 1 option.
Configure the Embedded NIC1 and NIC2 option by using the NIC management utilities of the system.
I/OAT DMA
Engine
Enables or disables the I/O Acceleration Technology (I/OAT) option. I/OAT is a set of DMA features
designed to accelerate network traffic and lower CPU utilization. Enable only if the hardware and
software support the feature.
Embedded Video
Controller
Enables or disables the use of Embedded Video Controller as the primary display. When set to Enabled,
the Embedded Video Controller is used as the primary display even if add-in graphic cards are installed.
When set to Disabled, an add-in graphics card is used as the primary display. BIOS will output displays
30 Pre-operating system management applications