Owners Manual
Table Of Contents
- About Your System
- Accessing System Features During Startup
- Front-Panel Features and Indicators
- LCD Panel Features
- Hard-Drive Indicator Patterns for RAID
- Back Panel Features and Indicators
- Power Indicator Codes
- NIC Indicator Codes
- LCD Status Messages
- System Messages
- Warning Messages
- Diagnostics Messages
- Alert Messages
- Other Information You May Need
- Using the System Setup Program and UEFI Boot Manager
- Installing System Components
- Recommended Tools
- Inside the System
- Front Bezel (Optional)
- Information Tag
- Opening and Closing the System
- Hard Drives
- Power Supplies
- Internal SD Module
- Internal SD Flash Card
- Internal USB Memory Key
- Internal USB Cable
- Integrated Dell Remote Access Controller 6 (iDRAC6) Enterprise Card (Optional)
- VFlash Media (Optional)
- NIC Hardware Key
- Cooling Shroud
- Cooling Fans
- Optical Drive
- Integrated Storage Controller Card
- RAID Battery
- Cable Routing
- Expansion Cards and Expansion-Card Risers
- Expansion Card Installation Guidelines
- Installing an Expansion Card
- Removing an Expansion Card
- Removing Expansion-Card Riser 1
- Replacing Expansion-Card Riser 1
- Removing Expansion-Card Riser 2
- Replacing Expansion-Card Riser 2
- Removing Expansion-Card Riser 2 From the Expansion-Card Bracket
- Replacing the Riser 2 Board on the Expansion-Card Bracket
- System Memory
- Processors
- System Battery
- Control Panel Assembly
- SAS Backplane (Service Only Procedure)
- System Board
- Troubleshooting Your System
- Safety First-For You and Your System
- Troubleshooting System Startup Failure
- Troubleshooting External Connections
- Troubleshooting the Video Subsystem
- Troubleshooting a USB Device
- Troubleshooting a Serial I/O Device
- Troubleshooting a NIC
- Troubleshooting a Wet System
- Troubleshooting a Damaged System
- Troubleshooting the System Battery
- Troubleshooting Power Supplies
- Troubleshooting System Cooling Problems
- Troubleshooting a Fan
- Troubleshooting System Memory
- Troubleshooting an Internal SD Card
- Troubleshooting an Internal USB Memory Key
- Troubleshooting an Optical Drive
- Troubleshooting a Hard Drive
- Troubleshooting a Storage Controller
- Troubleshooting Expansion Cards
- Troubleshooting the Processor
- Running the System Diagnostics
- Jumpers and Connectors
- Getting Help
- Index
66 Using the System Setup Program and UEFI Boot Manager
Serial Communication Screen
Option Description
Serial Communication
(On without Console
Redirection default)
Selects whether the serial communication devices
(Serial Device 1 and Serial Device 2) are enabled in
BIOS. BIOS console redirection can also be enabled and
the port address used can be specified.
Options are On without Console Redirection, On with
Console Redirection via COM1, On with Console
Redirection via COM2, and Off.
Serial Port Address
(Serial Device 1=COM1,
Serial Device2=COM2
default)
Sets the serial port addresses for the two serial devices.
NOTE: Only Serial Device 2 can be used for Serial Over
LAN (SOL). To use console redirection by SOL, configure
the same port address for console redirection and the
serial device.
External Serial Connector Specifies whether Serial Device 1, Serial Device 2, or
Remote Access Device has access to the external
serial connector.
NOTE: Only Serial Device 2 can be used for Serial Over
LAN (SOL). To use console redirection by SOL, configure
the same port address for console redirection and the
serial device.
Failsafe Baud Rate
(115200 default)
Displays the failsafe baud rate used for console
redirection. BIOS attempts to determine the baud rate
automatically. This failsafe baud rate is used only if the
attempt fails. This rate should not be adjusted.
Remote Terminal Type
(VT 100/VT220 default)
Sets the remote console terminal type, either
VT100/VT220 or ANSI.
Redirection After Boot
(Enabled default)
Enables or disables BIOS console redirection when the
operating system is loaded.