Dell EMC Server Deployment Pack Version 4.0 for Microsoft System Center Configuration Manager Installation Guide 1 June 2017 Rev.
Notes, cautions, and warnings NOTE: A NOTE indicates important information that helps you make better use of your product. CAUTION: A CAUTION indicates either potential damage to hardware or loss of data and tells you how to avoid the problem. WARNING: A WARNING indicates a potential for property damage, personal injury, or death. Copyright © 2009 - 2017 Dell Inc. or its subsidiaries. All rights reserved. Dell, EMC, and other trademarks are trademarks of Dell Inc. or its subsidiaries.
Contents Chapter 1: Overview...................................................................................................................... 4 Pre-requisites and requirements......................................................................................................................................4 Supported operating systems...........................................................................................................................................5 Supported systems...........
1 Overview This guide provides information on software pre-requisites and requirements to install and uninstall Dell EMC Server Deployment Pack (DSDP) for Microsoft System Center Configuration Manager—Configuration Manager.
● ● ● ● ● ● ● ● ● ○ OpenManage Server Driver Pack version 8.5 for 11th to 13th generation of PowerEdge servers. ○ OpenManage Server Driver Pack version 8.3 for 10th generation of PowerEdge servers. At least 100 MB of free disk space to install and use DSDP. KB articles are referred; for Configuration Manager 2012 R2 installed on a site server operating system Windows Server 2012 R2, see Microsoft KB 2907591.
Table 1. List of supported operating systems for installing Dell EMC Server Deployment Pack (continued) Operating system Configuration Manager Site Server Support Configuration Manager Admin Console Support Windows 8.1 Windows 8 Pro x64 Windows 8 Enterprise x64 Microsoft Windows 7 x86 and x64 Microsoft Windows Vista Business Edition x86 and x64 SP1 Supported systems For information on the supported Dell systems, see the Dell EMC Server Deployment Pack 4.0 Release Notes at Dell.com/ support/manuals.
Table 2. Compatible operating systems, DTK, and AIK/ADK versions supported by Dell EMC Server Deployment Pack for WinPE (continued) Configuration Manager Version WinPE Version Operating System Deployment DTK Versions AIK/ADK Version Configuration Manager 2012 SP1 4.0 ● Windows Server 2008 R2* ● Windows Server 2012 5.5 (10th to 13th generation PowerEdge servers) Windows ADK for Windows Server 2012 Configuration Manager 2012 3.0 ● Windows Server 2008 ● Windows Server 2008 R2 5.
Specifying a Fully Qualified Domain Name Specifying an FQDN in System Center Configuration Manager, 2012 SP2, 2012 R2 SP1, 2012 R2, 2012 SP1, or 2012 1. 2. 3. 4. 5. 6. 7. 8. Launch Configuration Manager Console. In the left pane of the Configuration Manager Console, click Administration. Expand Site Configuration and click Servers and Site System Roles. Click the server or site system. On the bottom pane under Site System Roles, right-click Site system and click Properties.
Deployment Pack Version 4.0 for Microsoft System Center Configuration Manager User’s Guide at Dell.com/support/ manuals. NOTE: To upgrade the Configuration Manager, on which DSDP is installed, to the newer version available, first upgrade the Configuration Manager to the newer version and then upgrade DSDP to the latest version. However, before you upgrade the console, Dell recommends that you delete all the Dell boot images that were created by using the earlier versions.
Migrating to Microsoft System Center Configuration Manager, 2012 SP2, 2012 R2 SP1, 2012 R2, 2012 SP1, or 2012 Dell recommends to uninstall DSDP (including any boot images, DTK utilities, and Windows PE Drivers) before you migrate your system to System Center Configuration Manager, 2012 SP2, 2012 R2 SP1, 2012 R2, 2012 SP1, or 2012. For more information on uninstalling DSDP, see Uninstalling DSDP.
2. Type the following command to uninstall DSDP: "" /s /x /v /L*v \"a.log\" /qn" For example: "DellEMC_Server_Deployment_Pack_4.0_for_Configuration_Manager.exe" /s /x /v /L*v \"a.log\" /qn" 3. To retain boot images, run the following command: "" /s /x /v" CP_REMOVEBOOTIMAGE="NO" /L*v \"a.log\" /qn" For example: "DellEMC_Server_Deployment_Pack_4.0_for_Configuration_Manager.exe" /s /x /v" CP_REMOVEBOOTIMAGE="NO" /L*v \"a.log\" /qn" NOTE: Delete all DSD
2. Type the following command to upgrade DSDP with the Remove Dell Deployment ToolKit (DTK) Utilities and Windows PE Drivers option. "" CP_WINPESTATE="RemoveWinPE" /qn /L*v For example: "DellEMC_Server_Deployment_Pack_4.0_for_Configuration_Manager.exe" CP_WINPESTATE="RemoveWinPE" /qn /L*v a.
Other Dell documents you might need In addition to this guide, you might need to refer the following documents to get details on specific Dell OpenManage products. These documents are available at Dell.com/support/manuals. ● The Dell EMC Server Deployment Pack Version 4.0 for Microsoft System Center Configuration Manager User’s Guide provides information on using DSDP 4.0 on your system.
○ ○ ○ ○ ○ ○ ○ ○ Enterprise Systems Management Mainframe Operating Systems Public Sector Solutions Serviceability Tools Support Utilities Virtualization Solutions 4. To view a document, click the required product and then click the required version. ● Using search engines: ○ Type the name and version of the document in the search box.
