Users Guide
Table Of Contents
- Lifecycle Controllerユーザーズ ガイド
- 目次
- はじめに
- Lifecycle Controller の使用
- Operating system deployment
- 監視
- ファームウェアアップデート
- 設定
- システムコントロールパネルのアクセスオプション
- iDRAC の設定
- システム時刻と日付の設定
- RAID の設定
- ソフトウェア RAID を使用した RAID の設定
- RAID コントローラ上でのセキュアな仮想ディスクの作成
- Key encryption
- ローカルキー暗号化モード
- ミラードライブの解除
- System setup — Advanced Hardware Configuration
- Collect System Inventory On Restart
- ローカル USB ドライブの設定
- NFS および CIFS サーバーの設定
- Conditions while configuring HTTP or HTTPS server
- 保守
- 使いやすいシステムコンポーネント名
- セットアップユーティリティとブートマネージャの使用
- トラブルシューティングとよくあるお問い合わせ(FAQ)
4. [ストレージ設定ウィザード] で [ミラーの解除] をクリックします。
ミラーリングされた仮想ドライブが記載された [ミラーの解除] ページが表示されます。
5. 関連コントローラを選択して、[終了]をクリックします。
メモ: [ミラーの解除]機能は、PERC 10.5、PERC 11、およびソフトウェア RAID コントローラーをサポートしていません。
正常にリンクが切り離されたミラーアレイがひとつであった場合でも、システムは自動的にオフになります。
System setup — Advanced Hardware Configuration
The Lifecycle Controller Advanced Hardware Configuration wizards allow you to configure BIOS, iDRAC, and certain devices such as NIC,
and RAID controllers through Human Interface Infrastructure (HII). HII is a UEFI-standard method for viewing and setting a device's
configuration. You can utilize a single utility to configure multiple devices that may have different pre-boot configuration utilities. The
utilities also provide localized versions of devices such as the BIOS setup.
Based on the system configuration, other device types may also appear under Advanced Hardware Configuration if they support the HII
configuration standard.
NOTE: When you update the firmware on a BCM57xx and 57xxx adapters, you will notice that the cards are displayed as QLogic.
This is due to the acquisition of Broadcom NetXtreme II by QLogic.
The Advanced Hardware Configuration wizard allows you to configure the following:
NOTE: You can also use System Setup utility during startup to configure the following devices. For more information about the
System Setup utility, see Using the system setup program and boot manager.
● System BIOS Settings
● iDRAC Device Settings
● NICs
NOTE: You can configure only one NIC at a time. For more information about the supported NIC cards, see white paper about
Network Adapter at https://www.dell.com/support/article/en-us/sln311809/lifecycle-controller?lang=ja.
If the System Configuration Lockdown mode is enable from iDRAC UI, any configuration on the particular system will not be permitted.
NOTE: This feature is available in Enterprise license.
Following are the exceptions for this feature:
● Power operations ( System power on, power off, reset)
● Setting power budget, power profiles
● Identify operations to blink an LED
● Run diagnostics
Integrated Broadcom NICs are controlled by both BIOS and the settings stored on the device itself. As a result, the Boot Protocol field in
the HII of integrated NICs has no effect; this setting is instead controlled by the BIOS on the Integrated Devices screen.
To set integrated NICs to an iSCSI or PXE boot mode, select System BIOS Settings, and then select Integrated Devices. In the list for
each embedded NIC, select the appropriate value:
● Enabled for no boot capability.
● Enabled with PXE to use the NIC for PXE boot.
● Enabled with iSCSI to use the NIC to boot from an iSCSI target.
デバイス設定の変更
[詳細ハードウェア設定] を使用してデバイス設定を変更するには、次の手順を実行します。
メモ: デバイス設定は、起動中に[System Setup(セットアップ)] ユーティリティを使用して変更することもできます。[System
Setup(セットアップ)] ユーティリティの詳細については、「セットアップユーティリティとブートマネージャの使い方」を
参照してください。
1. Lifecycle Controller を起動します。詳細については、「Lifecycle Controller の起動」を参照してください。
2. 左ペインで、[セットアップユーティリティ] を選択します。
3. 右ペインで、[詳細ハードウェア設定]をクリックします。
48 設定