Setup Guide

Broadcom OCM-CLI-LPE-UG124-100
91
Emulex OneCommand Manager Command Line Interface User Guide
This example displays the raw parameter specified:
hbacmd nvme-id-ns 10:00:00:90:fa:5d:05:a9 50:06:01:60:90:20:5C:38 nqn.2014-
08.com.example:nvme.host.sys.xyz 0x00000001 1 raw
Information similar to the following is displayed:
Raw data for namespace 0x00000001:
Standard data bytes:
Byte Dump
0000: 03 04 07 00 00 00 00 60 40 0c 70 06 8c 0a 00 00
0010: 04 02 00 0a 45 4d 55 4c 45 58 20 20 20 20 20 20
0020: 20 20 20 20 00 00 17 6a 41 46 42 52 2d 35 37 46
0030: 35 4d 5a 2d 45 4c 58 20 20 20 20 20 52 03 00 48
0040: 00 3a 00 00 41 41 31 32 32 31 4a 30 43 32 50 20
0050: 20 20 20 20 31 32 30 35 32 38 20 20 68 fa 05 3a
0060: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0070: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0080: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0090: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00A0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00B0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
…………: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
…………: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
…………: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0170: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
Vendor-specific data bytes:
Byte Dump
0180: 03 04 07 00 00 00 00 60 40 0c 70 06 8c 0a 00 00
0190: 04 02 00 0a 45 4d 55 4c 45 58 20 20 20 20 20 20
01A0: 20 20 20 20 00 00 17 6a 41 46 42 52 2d 35 37 46
01B0: 35 4d 5a 2d 45 4c 58 20 20 20 20 20 52 03 00 48
01C0: 00 3a 00 00 41 41 31 32 32 31 4a 30 43 32 50 20
01D0: 20 20 20 20 31 32 30 35 32 38 20 20 68 fa 05 3a
01E0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
01F0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0200: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0210: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0220: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0230: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
…………: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
…………: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
…………: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0FF0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
5.13.9 nvme-list
The nvme-list command lists the NVMe over FC subsystems recognized by the FC driver connected to the FC port. The
list contains all discovered subsystems, as well as those that were added to the subsystem table using the
nvme-set-sstable command.
Supported By
Linux and Windows