Users Guide
Table Of Contents
- Table of Contents
- Chapter 1: Introduction
- Chapter 2: Installation
- Chapter 3: Configuration
- 3.1 ESXi Command Line Tool Transition
- 3.2 FC Driver Configuration
- 3.2.1 Configuration Methods for FC Driver Parameters
- 3.2.2 Emulex ExpressLane Support
- 3.2.3 FC-SP-2 Authentication (DH-CHAP) Support
- 3.2.4 Trunking Support
- 3.2.5 Dynamically Adding LUNs
- 3.2.6 Dynamically Adding Targets
- 3.2.7 FC Driver Module Parameters
- 3.2.8 Creating an FC Remote Boot Disk
- 3.2.9 Managing Devices through the CIM Interface
- 3.2.10 Installing the Emulex CIM Provider
- 3.2.11 Creating, Deleting, and Displaying vPorts
- 3.2.12 Configuring VVols
- 3.2.13 Adjusting the LUN Queue Depth
- 3.3 Configuring NVMe over FC on a NetApp Target
- 3.4 Configuring NVMe over FC on an Initiator System
- Chapter 4: Troubleshooting the FC Driver
- Chapter 5: Troubleshooting the NVMe Driver
- Appendix A: esxcli Management Tool
- Appendix B: lpfc Driver BlockGuard Functionality
- Appendix C: Using the VMID Feature on a Brocade Switch
- Appendix D: Using the VMID Feature on a Cisco Switch
- Appendix E: NPIV Configuration
- Appendix F: License Notices
Broadcom DRVVM-UG128-100
75
Emulex Drivers for VMware ESXi User Guide
3172 Attempted to add already registered entry <uuid> with vmid: <cs_ctl>
Attempted to re-register a VMID entry.
ACTION: This is a software driver error. If this issue persists, report the error to Broadcom Technical Support.
3125: Not receiving unsolicited event <ret_val>
Mgmt Loopback Test. IOCB timed out.
ACTION: This is a software driver error. If this issue persists, report the error to Broadcom Technical Support.
3071: no memory for priority rules
Memory allocation for FCP priority rules setting failed.
ACTION: This is a software driver error. If this issue persists, report the error to Broadcom Technical Support.
1957 VMK_NO_PERMISSION Illegal BDE count <rcv_buf_cnt>
The driver received too many receive buffers for a loopback operation.
ACTION: This is a software driver error. If this issue persists, report the error to Broadcom Technical Support.
1949 VMK_NOT_EXEC NULL param passed to function
The driver tried to post a receive buffer, but no receive buffers are available.
ACTION: This is a software driver error. If this issue persists, report the error to Broadcom Technical Support.
1951 VMK_NO_MEMORY MBUF resources
The driver failed to get the memory buffer needed for a loopback test.
ACTION: This is a software driver error. If this issue persists, report the error to Broadcom Technical Support.
1950 VMK_NO_MEMORY IOCB resource not available
The driver could not allocate the IOCBs needed to post loopback receive buffers.
ACTION: This is a software driver error. If this issue persists, report the error to Broadcom Technical Support.
1935 Loopback did not receive data
The driver ran a loopback test but did not receive a response.
ACTION: This is a software driver error. If this issue persists, report the error to Broadcom Technical Support.
1934 VMK_NO_MEMORY DMA coherent resource unavailale
The driver failed to allocate a DMA buffer for an IOCTL request.
ACTION: This is a software driver error. If this issue persists, report the error to Broadcom Technical Support.
3171 Attempted to delete unregistered entry <uuid> with vmid: <vmid>
Unregistered VMID entry tried to be deleted.
ACTION: This is a software driver error. If this issue persists, report the error to Broadcom Technical Support.
3141 Loopback mode:<link_flags> not supported
Loopback mode passed by user not supported.
ACTION: Check the loopback mode passed. If this issue persists, report the error to Broadcom Technical Support.
3010: Run link diag test mailbox failed with mbx_status <value> status <value>, add_status <value>
Link diagnostics test failed.
ACTION: This is a software driver error. If this issue persists, report the error to Broadcom Technical Support.