Users Guide
Table Of Contents
- Table of Contents
- Chapter 1: Introduction
- Chapter 2: Installation
- Chapter 3: Configuration
- 3.1 ESXi Command Line Tool Transition
- 3.2 FC Driver Configuration
- 3.2.1 Configuration Methods for FC Driver Parameters
- 3.2.2 Emulex ExpressLane Support
- 3.2.3 FC-SP-2 Authentication (DH-CHAP) Support
- 3.2.4 Trunking Support
- 3.2.5 Dynamically Adding LUNs
- 3.2.6 Dynamically Adding Targets
- 3.2.7 FC Driver Module Parameters
- 3.2.8 Creating an FC Remote Boot Disk
- 3.2.9 Managing Devices through the CIM Interface
- 3.2.10 Installing the Emulex CIM Provider
- 3.2.11 Creating, Deleting, and Displaying vPorts
- 3.2.12 Configuring VVols
- 3.2.13 Adjusting the LUN Queue Depth
- 3.3 Configuring NVMe over FC on a NetApp Target
- 3.4 Configuring NVMe over FC on an Initiator System
- Chapter 4: Troubleshooting the FC Driver
- Chapter 5: Troubleshooting the NVMe Driver
- Appendix A: esxcli Management Tool
- Appendix B: lpfc Driver BlockGuard Functionality
- Appendix C: Using the VMID Feature on a Brocade Switch
- Appendix D: Using the VMID Feature on a Cisco Switch
- Appendix E: NPIV Configuration
- Appendix F: License Notices
Broadcom DRVVM-UG128-100
83
Emulex Drivers for VMware ESXi User Guide
0451 Adapter did not grant BlockGuard
The adapter firmware did not allow the driver to enable BlockGuard support. It is not a fatal error.
ACTION: No action required.
0599 Firmware Dump Image Present on Adapter
"Driver identified that a firmware dump image is present.
ACTION: No action required.
2616 txcmplq not empty<cnt> after <maxwait>
The completion queue is not yet drained after a particular time.
ACTION: No action required.
3468 Memory Allocated failed for FW logging
The memory is unavailable to store the firmware log buffer
ACTION: Report the error to Broadcom Technical Support.
2610 FCF <fcf_index> reached driver's book keeping dimension:< LPFC_SLI4_FCF_TBL_INDX_MAX>
The FCF index is beyond the driver allocated FCF table.
ACTION: Report the error to Broadcom Technical Support.
2920 Failed to alloc Resource IDs rc = <rc>
The port resources allocation itself has failed.
ACTION: Report the error to Broadcom Technical Support.
2925 Failed to issue CT ABTS RSP <Rctl> on xri <oxid>, Data <link_state>
The driver has failed to issue a Common transport abort sequence response command.
ACTION: Report the error to Broadcom Technical Support.
3154 BLS ABORT RSP failed, data: <ulpStatus><iocb.un.ulpWord[4]>
The BLS ABORT response command has failed.
ACTION: Report the error to Broadcom Technical Support.
0283 Failed to allocate mbox cmd memory
The memory allocation from the mailbox slab has failed.
ACTION: Report the error to Broadcom Technical Support.
3169 Abort failed: Abort INP: Data: <sli4_xritag> <ulpIoTag> <ulpContext> <ulpCommand>
An abort is issued to the command for which an abort has already been issued.
ACTION: No action required.
3167 Abort failed: issue_iocb: Data: <sli4_xritag> <ulpIoTag> <ulpContext> <ulpCommand>
The driver has failed to post the abort request for a command.
ACTION: Report the error to Broadcom Technical Support.
2800 Ring <ringno> full - portCmdGet <local_getidx>, ring max <port_max_cmd>
The ring to post the pending commands is full.
ACTION: No action required.