Users Guide
Table Of Contents
- Dell EqualLogic Host Integration Tools for Microsoft Edition Version 5.4 Installation and User's Guide
- About This Guide
- Introduction to Host Integration Tools
- Installation
- Obtain the Installation Kit
- Installation Considerations
- Install Host Integration Tools for Microsoft
- Install HIT/Microsoft on a Windows Server Core Machine
- Install HIT on a Windows Server Core Cluster
- About Remote Host Installations
- Install HIT on a Failover Cluster
- About Silent Installations
- Using HIT With a SharePoint Farm
- Remote Setup Wizard
- Remote Setup Command Line Utility
- Using the Multipath I/O Component
- Use the VDS Provider
- Use SCVMM With the Dell EqualLogic SMP
- Install the Dell EqualLogic Storage Management Provider
- Configure the Dell EqualLogic Storage Management Provider
- Create a Classification for Dell EqualLogic Storage Resources
- Import the SMP Through the SCVMM GUI
- Configure PS Series Groups
- Configure Group Access on Managed Hosts and Clusters
- Configure Storage for VM Rapid Provisioning
- Create a VM Template From a VHD
- Migrate the Rapid-Provisioned VMs
- Migrate Storage of a Deployed VM to Another Location
- Troubleshoot SCVMM Issues
- Supported SMP PowerShell Cmdlets
- Use the HPC iSCSI Provider
- Tools and Utilities
- Index
List or Modify MPIO Settings
Use the rswcli ‑MPIOParameters command to list or modify MPIO settings.
All parameters are optional. If no parameters are entered for this command, the current values for all parameters are listed.
The command syntax is as follows:
rswcli -MPIOParameters
-MaxSessionsPerVolumeSlice=1-4
-MaxSessionsPerEntireVolume=1-12
-DefaultLoadBalancing=LQD|RR|FO
-UseMPIOForSnapshots=yes|no
-UseIPv4 | -UseIPv6
-ClearDeviceLBPolicy
-MinAdapterSpeed=100|1000|10000 (as Mbps)
The following table describes the command parameters.
Table 8. List or Modify MPIO Settings Command Options
Parameter Argument Description
MaxSessionsPerVolumeSlice= 1‑- 4 Designates the maximum number of connections that MPIO
should use per volume per member.
MaxSessionsPerEntireVolume= 1‑- 12 Designates the maximum number of connections that MPIO
should use per volume for all members.
DefaultLoadBalancing= LQD|RR|FO Specifies the default load-balancing policy for MPIO as Least
Queue Depth (LQD), Round Robin (RR), or Failover Only (FO).
This change does not affect existing device load balancing
policy, unless the ‑ClearDeviceLBPolicy parameter is also
specified.
MinAdapterSpeed= 100|1000|10000 Specifies that MPIO will only use NICs that meet the minimum
speed specified in Mbps, if at least two NICs meet the speed.
UseMPIOForSnapshot= yes | no Specifies whether MPIO should be used for snapshots.
UseIPv4 Specifies that MPIO will use IPv4 IP addresses only. This
parameter is mutually exclusive with the ‑UseIPv6 parameter.
UseIPv6 Specifies that MPIO will use IPv6 IP addresses only. This
parameter is mutually exclusive with the ‑UseIPv4 parameter.
ClearDeviceLBPolicy Specifies that if the default load-balancing policy is changed,
then the load-balancing policies for individual devices should be
cleared if they are not set to use the default.
List Included and Excluded Subnets for MPIO
Use the rswcli ‑ListMPIO command to list subnets that are included or excluded for MPIO.
The default output for this command lists the adapters available. The state of each adapter is shown following the adapter
name, either included or excluded. Optionally, the rules used to generate the include and exclude lists can also be displayed.
The command syntax is as follows:
rswcli ‑ListMPIO [‑IncludeOnly | ‑ExcludeOnly] [-Detail]
The following table describes the command parameters.
NOTE: These parameters apply to the adapter list only. They do not apply to the rules list.
Remote Setup Command Line Utility 33