œµÂøžæÓ ¿Ø¡ˆ½³ºˆ Copyright 2009 Dell, Inc. 저작권 본사 소유 . Dell 은 Dell, Inc 의 상표입니다 . EqualLogic 은 등록 상표입니다 . 본 지침에서 언급한 모든 상표 및 등록 상표는 각 소유자의 자산입니다 . 이 문서의 정보는 사전 통보 없이 변경될 수 있습니다 . Dell 의 서면 승인 없이 어떠한 경우에도 무단 복제하는 것을 엄격히 금합니다 .
차례 서문 ............................................................................................................v 수용자 ...................................................................................................................v 구성 .......................................................................................................................v 설명서 ..................................................................................................................vi 기술 지원 및 고객 서비스 ...............
PS4000 하드웨어 유지보수 차례 마이크로 SD 카드 교체하기.................................................................... 3-18 4 전원 공급 장치 모듈 유지보수 ..................................................................... 4-1 LEDs 해석 .......................................................................................................... 4-1 오류 확인 ........................................................................................................... 4-1 전원 공급 장치 및 냉각 모듈 분리 ...................................................
서문 본 설명서는 PS4000 스토리지 배열용 하드웨어 유지보수 방법을 설명합니 다 . 각각의 배열에는 핫 스왑이 가능한 전원 공급 장치 및 냉각 모듈 , 8 개 또 는 16 개의 RAID 보호 디스크 , 단일 또는 듀얼 핫 스왑이 가능한 제어 모듈 이 포함되어 있습니다 . 하나 이상의 PS 시리즈 배열로 , 크기에 관계없이 사용이 편리하고 경제적 부담이 없는 자체 관리가 가능한 iSCSI 스토리지 영역 네트워크 (SAN)인 PS 시리즈 그룹을 생성할 수 있습니다 . 수용자 본 설명서는 PS4000 하드웨어 유지보수 담당 관리자용으로 고안되었습니다 . 관리자가 네트워크 또는 스토리지 시스템에 대해 포괄적인 경험을 가지고 있을 필요가 없습니다 .
PS4000 하드웨어 유지보수 서문 • 4 장 , 전원 공급 장치 모듈 유지보수 , 배열에 전원 및 냉각 기능을 제공하는 모듈을 설치 및 분리하는 방법을 설명합니다 . • 부록 A, 환경 , 전원 및 기타 사양 , PS4000 배열에 대한 사양을 설명합니다 . 설명서 PS 시리즈 배열 , 그룹 , 볼륨에 대한 세부 정보는 아래의 설명서를 참조하십 시오 : • PS 시리즈 발행 정보 . PS 시리즈 배열에 대한 최신 정보를 제공합니다 . • Dell EqualLogic PS 시리즈 배열 최종 사용자 라이센스 계약 (EULA) 보증 및 지원 정보 (WSI) 안전 , 환경 지침 및 규정 정보 (SERI) • • • PS 시리즈 설치 및 구성 . 배열 하드웨어 설치 방법 및 PS 시리즈 그룹 생성 방법 을 설명합니다 . 설치 및 설정 매뉴얼은 출력되어 제품과 함께 배송됩니다 . 사 용자의 배열 모델에 맞는 설명서를 사용하십시오 . • PS 시리즈 그룹 관리 .
PS4000 하드웨어 유지보수 서문 화 시스템은 이 코드를 사용하여 보다 효율적으로 고객의 전화 문의를 처리 합니다 . Dell 에 문의하기 Dell 은 다양한 온라인 및 전화 기반의 지원과 서비스 옵션을 제공합니다 . 제 공 여부는 국가 / 지역과 제품에 따라 차이가 있으며 일부 서비스는 소재 지 역에서 사용하지 못할 수 있습니다 . 미국 고객의 경우 800-945-3355 로 전화하십시오 . 주 : 인터넷 연결을 사용할 수 없는 경우에는 제품 구매서 , 포장 명세서 , 청 구서 또는 Dell 제품 카탈로그에서 연락처 정보를 찾을 수 있습니다 . 판매 , 기술 지원 또는 고객 서비스 문제에 대해 Dell 에 문의하려면 : 1. Support.dell.com 을 방문합니다 . 2. 창 하단의 Choose A Country/Region ( 국가 / 지역 선택해주세요 ) 드롭다 운 메뉴에서 한국을 선택합니다 . 3. 창 왼쪽에서 Contact Us ( 문의하기 ) 를 클릭합니다 . 4.
PS4000 하드웨어 유지보수 서문 다음 웹사이트를 통해 Dell 지원에 액세스할 수 있습니다 : • support.dell.com • support.dell.com/EqualLogic • support.jp.dell.com ( 일본 전용 ) • support.euro.dell.com ( 유럽 전용 ) 보증 정보 PS4000 배열 보증서는 배송상자에 포함되어 있습니다 . 보증서 등록에 관한 정보는 , support.dell.com/EqualLogic 을 방문하시기 바랍니다 .
1 기본 스토리지 배열 정보 이 장에는 PS4000 스토리지 배열에 대한 기본 정보가 포함되어 있습니다 . 배열 전면 및 후면 패널 PS4000 배열의 전면은 그림 1-1 및 그림 1-2 에 제시되어 있습니다 . 그림 1-1: PS4000 전면 패널 ( 베젤 포함 ) 그림 1-2: PS4000 전면 패널 ( 베젤 제외 ) 디스크 드라이브는 베젤을 제거한 후 전면에서 액세스가 가능합니다 . 디스 크 드라이브에 관한 세부 정보는 2 장을 참조하십시오 . PS4000 ( 타입 8 제어 모듈 포함 ) 의 후면에 있는 구성요소는 그림 1-2 에 제 시되어 있으며 표 1-1 에 설명되어 있습니다 . 주 : 이 설명서에 포함된 그림은 타입 8 제어 모듈을 보여주고 있습니다 . 다 르게 설명되어 있는 경우가 아니라면 , 이 설명서의 정보는 타입 8 및 타 입 9 제어 모듈에 적용됩니다 .
PS4000 하드웨어 유지보수 기본 배열 정보 그림 1-3: PS4000 후면 패널 표 1-1: 후면 패널 세부사항 설명 항목 설명 전원 공급 장치 및 냉각 모듈 오른쪽에 있는 모듈은 0 이고 왼쪽에 있는 모 듈은 1 입니다 . 제어 모듈 오른쪽에 있는 모듈은 0 이고 왼쪽에 있는 모듈은 1 입니다 . 작동 패널 LED. 배열 상태 ( 오류 및 경고 상태 ), 전원 상태 , 및 위치를 보 여주는 LEDs 가 포함됩니다 . 전원 공급 장치 및 냉각 모듈 전원 스위치 . 배열에 전원 켜기 및 끄기 . 작동 패널 LEDs 해석 작동 패널은 배열 하드웨어 구성요소를 모니터합니다 . 패널은 중복되어 있 지 않지만 , 오류가 발생하더라도 배열은 계속 작동합니다 . 작동 패널 유지 보수에 관한 정보는 배열 지원 서비스 제공업체에 문의하십시오 . 그림 1-4 는 작동 패널 LEDs 를 보여주며 , 이는 주의가 필요한 오류 및 상태 를 경고합니다 . 표 1-2 는 LEDs 를 설명합니다 .
기본 배열 정보 PS4000 하드웨어 유지보수 기타 배열 LEDs 에 관한 정보는 , 2-3 페이지의 디스크 드라이브 LEDs 해석 , 3-2 페이지의 제어 모듈 LEDs 해석 , 및 4-1 페이지의 LEDs 해석 을 참조하십 시오 . 그림 1-4: 작동 패널 표 1-2: 작동 패널 설명 항목 전원 LED 배열 탐지기 LED 상태 설명 꺼짐 전원이 들어오지 않음 . 녹색 전원 . 꺼짐 전원이 들어오지 않음 또는 정상 작동 . 주황색등이 깜 관리자가 배열 탐지기 기능을 활성화했습니다 . 박임 N/A 사용 안함 .
기본 배열 정보 PS4000 하드웨어 유지보수 표 1-2: 작동 패널 설명 ( 계속 ) 항목 경고 상태 LED 1–4 상태 설명 꺼짐 전원이 들어오지 않음 또는 정상 작동 . 주황색등이 깜 다음 중 하나 이상이 발생했습니다 : 박임 • RAID 세트 성능이 저하되었지만 정상 작동 . • RAID 세트 ( 볼륨 레벨 ) 블록 유실 . • 구성요소 온도가 한계에 가까움 . • 팬에 오류가 발생하거나 팬 RPMs 이 한계를 초과한 상태 . • 전원 공급 장치가 설치되지 않았거나 전원 이 공급되지 않음 . • 캐시 배터리 충전량이 72 시간 이하임 . • 제어 모듈이 1 개만 설치되었거나 제어 모듈 에 장애가 발생 . • 제어 모듈에 RAM 이 불충분함 . • 동기화 활성 및 보조 제어 모듈 . • 제어 모듈간에 통신이 이루어지지 않음 . • 설치한 예비 디스크에 RAID 세트의 디스크 를 교체할 정도의 용량이 없음 . • 중대한 영향을 주지 않은 하드웨어 구성요 소에 오류 발생 .
기본 배열 정보 PS4000 하드웨어 유지보수 표 1-2: 작동 패널 설명 ( 계속 ) 항목 상태 설명 꺼짐 전원이 들어오지 않음 또는 정상 작동 . 중대한 오류 상 주황색등이 깜 다음 중 하나 이상이 발생했습니다 : 박임 • RAID 가 정상적으로 작동하지 않음 . 태 LED • 로스트 블록 테이블이 가득참 . • 배열 온도가 상한값 또는 하한값을 초과한 상태 . • 제어 모듈 캐시 데이터 유실 . • 냉각 모듈이 설치되지 않음 . • 냉각 모듈의 2 개 팬 모듈 모두에 오류 발생 . • 캐시 배터리 온도가 너무 높아 배터리 충전 할 수 없음 . • NVRAM 코인 셀 배터리에 오류 발생 . • 캐시는 설치한 어떤 디스크에 속하지 않은 데이터를 포함함 . • 하나 이상의 유효한 RAID 세트가 배열에 존 재함 . • 제어 모듈이 다른 모델임 . • 중대한 영향을 주는 하드웨어 구성요소에 오류 발생 . • 작동 패널에 오류가 발생하거나 설치되지 않음 .
PS4000 하드웨어 유지보수 기본 배열 정보 그림 1-5: 정전기 손목 보호대 배열 종료 및 재시작 PS4000 배열에는 중복적이고 , 핫 스왑이 가능한 디스크 , 전원 공급 장치 및 제어 모듈 ( 듀얼 제어 모듈 배열의 경우 ) 이 포함됩니다 . 정상 작동을 하는 구성 요소가 있는 경우 , 작동에 영향을 미치지 않고 중복되는 구성 요소를 제거할 수 있습니다 . 그렇지 않은 경우 , 구성 요소를 제거하기 전에 완전히 배열을 종료하고 전원을 끌 것을 권장합니다 . 주 : 배열을 종료하면 배열이 성공적으로 재시작 될 때까지 배열의 데이터 와 함께 볼륨이 오프라인으로 설정됩니다 . 이러한 작업은 볼륨에 연결 된 초기자에 영향을 미칠 수 있습니다 . 1. 다음 중 한 절차를 실행하십시오 : • 텔넷 또는 SSH 를 사용하여 배열의 네트워크 인터페이스에 지정된 기능적 IP 주소에 연결합니다 . 그룹 IP 주소에 연결하지 마십시오 .
PS4000 하드웨어 유지보수 기본 배열 정보 2. 예를 들어 , grpadmin 계정과 같이 읽기 - 쓰기 액세스가 가능한 계정에 로그인합니다 . 3. 다음과 같이 shutdown 명령을 입력합니다 . login: grpadmin Password: Welcome to Group Manager Copyright 2001-2009 Dell, Inc. group1> shutdown 배열 종료를 위해 직렬 연결을 사용하는 경우 , " 아무 키나 누르십시오 " 메 시지가 나타날 때 전원을 끄는 것이 안전합니다 . ( 아무 키나 누르면 제어 모 듈이 재시작됩니다 .) 네트워크 연결을 사용하는 경우 , 배열이 완전히 종료되기 전에 세션의 연결 이 끊어집니다 . 각각의 제어 모듈의 CACT LED 가 배열의 전원을 끄기 전에 꺼져 있는지 ( 점등되지 않은 상태인지 ) 확인합니다 . 배열 유지보수를 수행한 후 , 배열에 대한 전원을 끌 수 있습니다 .
PS4000 하드웨어 유지보수 1–8 기본 배열 정보
2 디스크 드라이브 유지보수 배열에는 직렬 부착 SCSI (SAS) 또는 직렬 ATA (SATA) 인 핫스왑이 가능한 디스크 드라이브가 최대 16 개 포함되어 있습니다 . 디스크 드라이브 유지보 수 항목들은 SAS 및 SATA 디스크 드라이브에 모두 적용됩니다 . 베젤 분리 디스크 드라이브에 접근하려면 베젤을 분리해야 합니다 . 베젤은 잠금 장치와 함께 제공되며 , 잠금 장치는 디스크 드라이브가 변경되 거나 뜻하지 않게 분리되지 않도록 합니다 . 베젤의 잠금 장치를 해제하고 분리하려면 : 1. 베젤 키를 삽입하고 시계 방향으로 돌려 베젤을 잠금 해제합니다 . 그림 2-1 을 참조하십시오 . 그림 2-1: 베젤 잠금 해제 2. 베젤 분리 래치를 밀어 올려 섀시에서 베젤을 분리합니다 . 그림 2-2 를 참조하십시오 .
PS4000 하드웨어 유지보수 디스크 유지보수 그림 2-2: 베젤 분리 래치 누르기 3. 베젤을 잡고 섀시에서 밖으로 당깁니다 . 그림 2-3 을 참조하십시오 .
디스크 유지보수 PS4000 하드웨어 유지보수 디스크 드라이브 LEDs 해석 그림 2-4 는 배열에서 디스크 드라이브의 방향 설정 방법과 넘버링 방법을 설명합니다 . 그림 2-4: 디스크 드라이브 넘버링 디스크 드라이브 부품은 그림 2-5 에서 제시하고 표 2-1 에서 설명합니다 . 그림 2-5: 디스크 드라이브 세부사항 표 2-1: 디스크 드라이브 세부사항 설명 Callout 항목 색상 설명 디스크 드라이브 손잡이 분리 단추 검정색 SAS 디스크 드라이브 . 회색 SATA 디스크 드라이브 . 손잡이 회색 SAS 및 SATA 디스크 드라이브에 대해 동일함 .
디스크 유지보수 PS4000 하드웨어 유지보수 표 2-1: 디스크 드라이브 세부사항 설명 ( 계속 ) Callout 항목 색상 설명 전원 및 디스크 드 라이브 작동 LED 꺼짐 전원 없음 또는 오류가 없는 상태 . 녹색 전원 . 녹색으로 깜박임 디스크 드라이브 작동 . 오류 LED 꺼짐 전원이 들어오지 않음 또는 정상 작동 . 적색 오류 상태 . 디스크 드라이브 취급 요건 디스크 드라이브를 다음과 같이 취급합니다 : • • • • • • • 2–4 드라이브를 올바르게 보관합니다 . 제공시 디스크 드라이브가 들어있던 포장에 교체용 디스크 드라이브를 보관하십시오 . 디스크 드라이브를 쌓 거나 디스크 드라이브 상단에 물건을 올려 놓지 마십시오 . 디스크 드라이브를 정전기 방전으로부터 보호하십시오 . 정전기 방전으 로부터 보호를 받지 못하는 경우 , 디스크 드라이브 취급시 정전기 손목 보호대를 착용하십시오 . 디스크 드라이브를 주의하여 취급하십시오 .
PS4000 하드웨어 유지보수 디스크 유지보수 고장난 디스크 드라이브 확인 디스크 드라이브 오류는 다음과 같이 표시됩니다 : • • • 디스크 드라이브의 LEDs. 2-3 페이지의 디스크 드라이브 LEDs 해석 을 참조하십시오 . 콘솔 , 이벤트 로그 또는 그룹 관리자 GUI 경보 패널에 표시된 메시지는 디스크 드라이브 오류를 설명합니다 . GUI 멤버 디스크 창 또는 CLI 멤버 선택 보기 디스크 명령 결과가 디스크 드라이브 오류로 표시됩니다 . 디스크 드라이브 고장시 배열의 동작 배열이 디스크 드라이브 오류를 처리하는 방식은 예비 디스크 드라이브의 이용 가능 여부와 고장난 디스크 드라이브를 포함하고 있는 RAID 세트 성능 의 저하 여부에 따라 달라집니다 . 예를 들면 다음과 같습니다 . • • • • 예비 디스크 드라이브를 사용할 수 있는 경우 , 고장난 디스크가 교체됩 니다 . 재구성이 완료되면 성능은 정상이 됩니다 .
PS4000 하드웨어 유지보수 디스크 유지보수 디스크 드라이브 제거 주의 : 주: 디스크 드라이브를 취급할 때 정전기 보호 장치를 착용하십시오. 1-5 페이지의 정전기 손목 보호대 사용 을 참조하십시오 . 고장난 디스크를 가능한 빨리 교체해 가장 높은 가용성을 제공하십 시오 . 교체할 다른 디스크 드라이브 또는 빈 캐리어가 준비될 때까지 디스 크 드라이브를 슬롯에서 분리하지 마십시오 . 각각의 슬롯에는 디스 크 드라이브 또는 빈 캐리어가 반드시 포함됩니다 . 예비 디스크 드라이브가 준비될 때까지 정상적으로 작동하는 디스 크를 배열에서 분리하지 마십시오 . 분리하는 경우 , RAID 세트의 성 능이 저하될 수 있습니다 . 예비 디스크 드라이브를 분리한 경우 , 가 능한 신속하게 교체하십시오 . 정상적으로 작동하는 디스크 드라이브를 배열 슬롯에서 완전히 분 리하기 전에 , 디스크 드라이브가 회전을 멈추고 헤드가 정지할 때까 지 30 초를 기다립니다 .
PS4000 하드웨어 유지보수 디스크 유지보수 그림 2-6: 디스크 드라이브 분리 3. 헤드가 정지하도록 30 초를 기다립니다 . ( 빈 캐리어를 분리할 때는 해 당되지 않습니다 .) 4. 디스크 드라이브를 슬롯에서 더 당기고 손잡이를 재설치합니다 . 딸깍하 는 소리가 들립니다 . 디스크 드라이브를 배열에서 완전히 당깁니다 . 디스크 드라이브 설치 지침 및 제한 • • • 용량 , 속도 , 스핀 속도가 동일한 디스크 드라이브만을 배열에 설치하십 시오 . 손잡이 분리 버튼의 색상은 디스크 드라이브 유형을 나타냅니다 (SAS 는 검정색 ; SATA 는 회색 ). 손잡이 분리 버튼이 왼쪽을 향하고 디스크 드라이브가 그림 2-4 와 같은 방향이 되도록 합니다 . 배열에 다른 크기의 디스크 드라이브를 사용할 수 있습니다 . 그러나 , 배 열의 가장 작은 디스크 드라이브가 각각의 디스크 드라이브에서 얼마나 많은 공간을 사용할 지 결정합니다 .
PS4000 하드웨어 유지보수 • • • • • 디스크 유지보수 손잡이를 누르기 전에 디스크 드라이브가 섀시에 완전히 삽입되도록 합 니다 . 올바르게 설치된 경우 , 디스크 드라이브 높이가 배열 전면과 동일해집 니다 . 디스크 드라이브가 배열에서 튀어나온 경우 , 디스크 드라이브를 재설치하십시오 . 설치 후 , 디스크 드라이브 전원 LED ( 상단 ) 이 녹색이거나 녹색이 깜박 이는지 확인합니다 . 디스크 드라이브를 삽입하고 디스크 드라이브가 자동으로 RAID 세트를 구성하는데까지 2 분 정도 걸립니다 . 2 분 정도의 시간 간격으로 다중 디스크 드라이브가 배열에 동시에 구성됩니다 . 이는 단일 디스크 드라 이브를 설치하고 , 구성하고 , 해당 과정을 반복하는 것보다 효율적입니 다 . 예를 들어 , 디스크 드라이브를 설치하면 , 타이머가 시작됩니다 . 다 른 디스크 드라이브를 설치하지 않을 경우 , 디스크 드라이브는 2 분 정 도의 시간이 경과된 후 구성됩니다 .
PS4000 하드웨어 유지보수 디스크 유지보수 그림 2-7: 디스크 드라이브 손잡이 닫기 새 디스크 드라이브가 작동하는지 2-3페이지의 디스크 드라이브 LEDs 해석 에 설명된대로 전면 패널의 LEDs 를 검사해 확인합니다 . 또한 , GUI 멤버 디 스크 창과 CLI 멤버 선택 보기 디스크 명령의 결과를 확인합니다 . 베젤 설치 모든 교체용 디스크 드라이브 또는 보호물을 설치한 후 , 베젤을 재설치하고 잠급니다 . 1. 배열의 전면을 마주하고 베젤 오른쪽을 섀시 오른쪽에 맞춥니다 . 2. 베젤의 왼쪽이 섀시와 맞물릴 때까지 섀시쪽으로 베젤을 누릅니다 . 3. 베젤 키를 삽입하고 시계 반대 방향으로 돌려 베젤을 잠금니다 . 4. 키를 안전한 장소에 보관하십시오 .
3 제어 모듈 유지보수 PS4000 배열에는 1 개 또는 2 개의 핫스왑이 가능한 제어 모듈이 들어 있습 니다 . 배열 작동에는 기능적 제어 모듈 1 개가 필요합니다 . 배열의 후면에 서 제어 모듈에 액세스할 수 있습니다 . 제어 모듈 PS4000 배열에는 2 개의 타입 8 또는 2 개의 타입 9 제어 모듈이 들어 있습니 다 . 그림 3-1 및 그림 3-2 를 참조하십시오 . 그림 3-1: 타입 8 제어 모듈 그림 3-2: 타입 9 제어 모듈 각각의 제어 모듈에는 다음이 포함되어 있습니다 : • iSCSI 또는 처리량 관리를 위한 2 개의 기가비트 iSCSI 이더넷 포트 • 10Mb/100Mb 관리 포트 1 개 ( 관리 네트워크를 구성한 경우에만 사용됨 ) • 시리얼 커넥터 1 개 ( 배열에 대한 네트워크 액세스가 없는 경우에만 사 용됨 ) • PS 시리즈 펌웨어를 실행중인 펌웨어 카드 . 타입 8 에서는 컴팩트 플래 시 카드입니다 . 타입 9 에서는 마이크로 SD 카드입니다 .
제어 모듈 유지보수 PS4000 하드웨어 유지보수 활성 제어 모듈이 고장난 경우 , 2 차 제어 모듈이 네트워크 작업을 대신 처리 합니다 . 배열에 제어 모듈 종류를 혼합하여 사용하지 마십시오 . 제어 모듈의 종류와 색상이 동일한지 반드시 확인하십시오 . 지원되는 다른 제어 모듈에 대한 정 보는 최신 PS 시리즈 발행 정보를 확인하십시오 . 제어 모듈 LEDs 해석 제어 모듈에는 다음의 LEDs 가 구성되어 있습니다 : • 각각의 제어 모듈의 왼쪽에 있는 LEDs 3 개를 통해 제어 모듈의 상태와 해당 제어 모듈이 활성 상태인지 혹은 보조 상태인지 결정할 수 있습니 다 . 그림 3-1 및 그림 3-2 를 참조하십시오 . • 각 이더넷 포트에는 네트워크 인터페이스 상태를 표시하는 LED 가 2 개 있습니다 . 그림 3-1 및 그림 3-2 를 참조하십시오 . 제어 모듈 LEDs 는 표 3-1 에 설명되어 있습니다 . 이더넷 포트 LEDs 는 표 3-2 에서 설명합니다 .
제어 모듈 유지보수 PS4000 하드웨어 유지보수 표 3-2: 이더넷 포트 LED 설명 LED 위치 색상 설명 각 포트 왼쪽 꺼짐 전원 없음 또는 네트워크에 연결되지 않음 . 녹색 네트워크에 연결됨 . 꺼짐 전원 없음 , 전송 없음 또는 수신 없음 . 녹색 전송중 또는 수신중 . 각 포트 오른쪽 제어 모듈 오류 식별 다음으로 제어 모듈 오류를 식별할 수 있습니다 : • LEDs. 3-2 페이지의 제어 모듈 LEDs 해석 을 참조하십시오 . • 메시지 . 제어 모듈 오류를 나타내는 메시지가 ( 베젤 뒤쪽에 있는 ) LCD 패널 , 콘솔 , 이벤트 로그 또는 그룹 관리자 GUI 경보 패널에 표시됩니다 . • 그룹 관리자 GUI 및 CLI 출력 . 멤버 컨트롤러 창 또는 멤버 선택 보기 컨 트롤러 명령으로 설치되지 않은 상태의 제어 모듈이 표시됩니다 . 배열의 후면에서 보면 , CM0 은 오른쪽에 있고 CM1 은 왼쪽에 있습니다 . 그림 1-3 을 참조하십시오 .
PS4000 하드웨어 유지보수 제어 모듈 유지보수 PS 시리즈 배열은 2 가지 유형의 네트워크 장애 보호를 제공합니다 : • 네트워크 연결 장애극복. 다수의 네트워크 인터페이스가 구성되어 있고 1 개의 네트워크 인터페이스가 고장난 경우 , 고장난 인터페이스에 연결 된 iSCSI 초기자는 그룹 IP 주소에 다시 연결할 수 있으며 기능적 인터페 이스에 재지정할 수 있습니다 . 예를 들어 , 단일 제어 모듈 어레이에서 , 이더넷 0 과 이더넷 1 이 네트워크에 연결되어 있고 이더넷 0 이 고장난 경우 , 이더넷 0 에 연결된 초기자는 이더넷 1 로 재지정이 가능합니다 . • 제어 모듈 장애극복 . 듀얼 제어 모듈 어레이에서 , 활성 제어 모듈이 고 장난 경우 2 차 제어 모듈이 자동으로 대체되고 활성화됩니다 . 케이블이 새로이 활성화된 제어 모듈의 포트에 연결되면 , 네트워크 I/O 는 그러한 인터페이스를 통해 계속해서 구성이 가능합니다.
제어 모듈 유지보수 PS4000 하드웨어 유지보수 네트워크 구성 권장사항 Dell 은 표 3-3 의 지침을 따를 것을 권장합니다 . 또한 , 적절한 네트워크 구 성을 위한 모든 일반 규칙들이 그룹 멤버에 적용됩니다 . 일반적인 네트워크 구성은 이 설명서의 적용범위를 벗어난 주제입니다 . 표 3-3: 네트워크 권장사항 권장사항 설명 교환 기가비트 이더넷 배열 및 호스트를 스위치 네트워크에 연결하고 호스트와 배 네트워크 열 간의 모든 네트워크 연결이 기가비트 이더넷이 되도록 합 니다 . 배열은 10 또는 100 메가비트에서 작동되지만 , 기가 비트 이더넷 스위치를 사용할 경우 성능이 저하됩니다 . 다중 네트워크 연결 대역폭 증가와 가용성 증가를 위해 , 두 개의 제어 모듈에 있 는 이더넷 0 과 이더넷 1 을 다중 네트워크 스위치에 연결합 니다 . 스위치는 스위치간 링크를 사용하여 연결되어야 합니다 . 그 러한 스위치간 링크는 iSCSI 트래픽을 처리할 수 있을 정도 로 대역폭이 충분해야 합니다 .
PS4000 하드웨어 유지보수 제어 모듈 유지보수 표 3-3: 네트워크 권장사항 ( 계속 ) 권장사항 설명 엔드 노드를 연결하는 가능한 경우 , 엔드 노드를 연결하는 스위치 포트에 스패닝 스위치 포트에 STP 기 트리 프로토콜 (STP) 를 사용하지 마십시오 (iSCSI 초기자 또 능이 없습니다 . 는 스토리지 배열 네트워크 인터페이스 ). 그러나 , STP 또는 RSTP (STP 보다 선호됨 ) 를 사용해야 하 는 경우 , 링크시 상태를 전달하는 STP 로 포트를 즉시 변화 시키는 ( 몇몇 스위치에서 사용 가능한 ) 포트 설정을 활성화 시켜야 합니다 . 이 기능을 사용하면 장치를 재시작할 때 발 생되는 네트워크 간섭을 줄일 수 있으므로 이 기능은 엔드 노드를 연결하는 스위치 포트에서만 활성화시켜야 합니다 . 스위치 간의 단일 케이블 연결에는 스패닝 트리를 사용할 수 있으며 , 스위치 간의 다중 케이블 연결에는 트렁킹을 사용 할 수 있습니다 .
PS4000 하드웨어 유지보수 제어 모듈 유지보수 • 네트워크 인터페이스를 다른 네트워크 스위치에 연결합니다 . • 듀얼 제어 모듈 배열에서 , 하나의 제어 모듈이 고장난 경우 연결성을 보 장할 수 있도록 각각의 제어 모듈에 있는 인터페이스 포트에 케이블을 연결합니다 . 예를 들어 , CM0 의 이더넷 0 과 CM1 의 이더넷 0 에 케이 블을 연결한 다음 , 케이블을 네트워크 스위치에 연결합니다 . 단일 제어 모듈 배열의 경우 , 최소 네트워크 구성은 이더넷 0 에 하나의 네트 워크 연결을 구성하는 것입니다 . 그러나 , 단일 네트워크 연결은 잠재적인 고장점이며 대역폭을 제한합니다 . Dell 은 이더넷 0 과 이더넷 1 을 다른 네 트워크 스위치에 연결할 것을 권장합니다 . 예를 들어 , 그림 3-3 과 같이 케이블을 연결한 경우 , 이더넷 0 이 고장나면 개시 프로그램을 이더넷 1 로 재지정할 수 있습니다 .
PS4000 하드웨어 유지보수 제어 모듈 유지보수 그림 3-4: 최소 네트워크 구성 그림 3-5 는 스위치간 링크에 연결되어 있고 이더넷 0 과 이더넷 1 을 다른 스 위치에 연결하기 위해 사용되는 듀얼 제어 모듈 배열을 위한 권장 네트워크 구성을 나타냅니다 . 이러한 구성은 가장 높은 수준의 네트워크 가용성 및 최대 수준의 네트워크 대역폭을 제공합니다 .
PS4000 하드웨어 유지보수 제어 모듈 유지보수 제어 모듈 취급 요구사항 이러한 제어 모듈 취급 요구사항을 따릅니다 : • 제어 모듈을 정전기 방전으로부터 보호하십시오 . 1-5 페이지의 정전기 손목 보호대 사용 에 설명된대로 제어 모듈을 취급할 때에는 반드시 정 전기 손목 보호대를 착용하십시오 . 제어 모듈을 설치하지 않은 경우 , 정 전기 방지 주머니에 제어 모듈을 보관하거나 정전기 방전으로부터 보호 처리된 표면에 올려놓아야 합니다 . • 제어 모듈이 동기화되는 동안에는 어레이에서 제어 모듈을 분리하지 마 십시오 . 동기화가 완료되면 콘솔 메시지가 표시됩니다 . 또한 , 2 차 제어 모듈의 ACT LED 가 주황색이 됩니다 . • 제어 모듈 슬롯을 빈 상태로 남겨두지 마십시오 . 제어 모듈이 1 개인 어 레이에서는 반드시 블랭크 케이블 보호용 덮개를 빈 상태의 제어 모듈 슬롯에 부착하십시오 . • 제어 모듈을 적절하게 보관합니다 .
PS4000 하드웨어 유지보수 제어 모듈 유지보수 그렇지 않은 경우 , 가능하다면 , 1-6 페이지의 배열 종료 및 재시작 에 설명 된대로 모듈을 제거하기 전에 배열을 완전히 종료합니다 . 주의 : 제어 모듈이 동기화되는 동안에는 어레이에서 제어 모듈을 분리 하지 마십시오 . 동기화가 완료되면 콘솔에 메시지가 표시됩니 다 . 동기화가 완료되면 2 차 제어 모듈의 ACT LED 가 주황색이 됩니다 . 제어 모듈을 제거하기 전에 : • 1-5 페이지의 정전기 손목 보호대 사용 에 설명된대로 정전기 손목 보호 대를 부착합니다 . • 제어 모듈에 부착된 직렬 또는 네트워크 케이블을 분리합니다 . 선택적 으로 , 네트워크 케이블을 작동중인 제어 모듈에 다시 장착해 데이터 액 세스를 연속으로 제공할 수 있습니다 . 제어 모듈을 분리하려면 : 1. 각각의 래치에 대한 분리기구를 꽉 쥐고 각각의 래치를 바깥쪽으로 돌려 서 제어 모듈 래치를 엽니다 . 이렇게 하면 배열에서 제어 모듈이 분리됩 니다 .
PS4000 하드웨어 유지보수 제어 모듈 유지보수 그림 3-6: 제어 모듈 래치 열기 2. 래치를 잡고 슬롯에서 제어 모듈을 주의하여 잡아당깁니다 . 그림 3-7 을 참조하십시오 .
PS4000 하드웨어 유지보수 제어 모듈 유지보수 그림 3-7: 제어 모듈 제거하기 3. 제어 모듈을 정전하 보호가 되는 평평한 표면에 놓으십시오 . 주의 : 손상을 방지하려면 제어 모듈 상단에 아무 것도 놓지 마십시오 . 4. 고장난 제어 모듈을 교체하는 경우 , 고장난 제어 모듈에서 컴팩트 플래 시 카드를 제거하고 교체용 제어 모듈에 설치하십시오 . 이렇게 하면 교 체용 제어 모듈이 올바른 펌웨어를 실행하도록 할 수 있습니다 . - 타입 8 제어 모듈은 3-16 페이지의 컴팩트 플래시 카드를 교체하기 전에 를 참조하십시오 . - 타입 9 제어 모듈은 3-18 페이지의 마이크로 SD 카드 교체하기 를 참 조하십시오 . 교체용 제어 모듈을 설치하거나 펌웨어 카드를 교체한 후 제어 모듈을 재설 치하려면 3-13 페이지의 제어 모듈 설치하기 를 참조하십시오 . 제어 모듈 슬 롯이 비어 있는 상태에서 배열을 작동하지 마십시오 .
PS4000 하드웨어 유지보수 제어 모듈 유지보수 고장난 제어 모듈은 교체 모듈이 들어 있던 포장에 넣어 반환하십시오 . 하 드웨어 반환에 대한 자세한 정보는 PS 시리즈 지원 제공업체에 문의하십시 오. 제어 모듈 설치하기 배열을 종료하지 않은 상태에서 제어 모듈을 설치할 수 있습니다 . 주의 : 배열에 제어 모듈 종류를 혼합하여 사용하지 마십시오 . 제어 모듈을 설치하기 전에 , 제어 모듈의 펌웨어가 기능적 제어 모듈에서 실행중인 펌웨어와 일치하는지 확인합니다 . 3-4 페이지의 제어 모듈 펌웨어 유지 관리 를 참조하십시오 . 래치 장치는 인접한 전원 공급 장치 및 냉각 모듈과 마주보게 하여 , 제어 모 듈을 배열에 수직으로 설치합니다 . 그림 3-8 을 참조하십시오 . 그림 3-8: 올바른 제어 모듈 방향 주의 : 제어 모듈을 취급할 때 정전기 보호 장치를 착용하십시오 . 1-5 페이지의 정전기 손목 보호대 사용 을 참조하십시오 . 제어 모듈을 설치하려면 : 1.
PS4000 하드웨어 유지보수 제어 모듈 유지보수 그림 3-9: 제어 모듈 설치하기 5. 3-6 페이지의 네트워크 케이블 연결 에 따라 네트워크 케이블을 연결합 니다 . 6. 배열을 종료하였으면 , 배열에 대한 전원을 켭니다 . 7. 3-2 페이지의 제어 모듈 LEDs 해석 에 따라 LEDs 를 점검합니다 . 또한 , GUI 멤버 컨트롤러 창을 검사하거나 CLI 멤버 선택 보기 컨트롤러 명령 을 실행합니다 . 제어 모듈 상태는 활성 ( 제어 모듈이 1 개인 경우 ) 이거 나 보조입니다 . 2 개의 제어 모듈이 설치되어 있지만 GUI 또는 CLI 에 1 개만 표시되는 경우 , 제어 모듈이 적절하게 설치되지 못할 수 있습니다 . 제어 모듈을 다시 장착합 니다 . 2 개의 제어 모듈 모두가 GUI 또는 CLI 에 나타나지 않는 경우 , 동일한 펌웨어를 실행하지 않을 가능성이 있습니다 . 배열 지원 서비스 제공업체에 문의하십시오 .
PS4000 하드웨어 유지보수 주: 제어 모듈 유지보수 연결이 되면 제어 모듈 캐시 배터리가 충전을 시작할 수 있습니다 . 배터리 부족 보호 캐시 정책이 활성화되면 ( 기본값 ), 캐시 배터리가 완전히 충전될 때까지 연속기입 모드에서 실행됩니다 . 그러나 배터리가 완전히 충전되기 전에 최적 성능이 필요한 경우 , 배터리 상태가 양호 / 충전중이라면 일시적으로 저전압 보호 정책을 비활성화하고 배열을 후기입 모드에서 작동시킬 수 있습니다 . 배터 리가 완전히 충전되면 저전압 보호 정책이 재활성화되었는지 확인 합니다 . 캐시 정책에 대한 정보는 PS 시리즈 그룹 관리 설명서를 참 조하십시오 . 펌웨어 카드 교체하기 PS 시리즈 배열에 있는 제어 모듈은 PS 시리즈 펌웨어를 실행하는 펌웨어 카 드를 포함하고 있습니다 .
PS4000 하드웨어 유지보수 주의 : 제어 모듈 유지보수 회로 보드가 손상되지 않도록 주의하십시오 . 날카로운 도구를 사용하여 카드를 분리하지 마십시오 . 컴팩트 플래시 카드를 교체하기 전에 1. 카드의 양쪽을 꽉 잡고 커넥터에서 밀어냅니다 . 카드 또는 제어 모듈 회 로판이 손상되지 않도록 합니다 . 그림 3-10 을 참조하십시오 . 그림 3-10: 컴팩트 플래시 카드 제거하기 2. 교체용 제어 모듈에 컴팩트 플래시 카드를 넣으려면 , 커넥터와 카드의 양쪽에 있는 홈을 맞추고 카드에 있는 빨간색 화살표가 커넥터를 향하고 있는지 확인합니다 . 그림 3-11 을 참조하십시오 .
PS4000 하드웨어 유지보수 제어 모듈 유지보수 그림 3-11: 컴팩트 플래시 카드 넣기 3. 컴팩트 플래시 카드를 적절한 위치에 대고 꽉 누릅니다 . 4. 제어 모듈을 설치합니다 . 3-13 페이지의 제어 모듈 설치하기 를 참조하 십시오 .
PS4000 하드웨어 유지보수 제어 모듈 유지보수 마이크로 SD 카드 교체하기 1. 카드를 카드 몸체로 단단히 밀어 스프링 장치를 분리합니다 ( 그림 3-12 ). 마이크로 SD 카드의 일부가 몸체에서 나옵니다 . 그림 3-12: 마이크로 SD 카드 꺼내기 2. 카드를 몸체에서 조심스럽게 바로 위로 잡아 당깁니다 . 3. 마이크로 SD 카드를 정전하 보호가 되는 평평한 표면에 놓으십시오 . 4. 교체용 제어 모듈에 마이크로 SD 카드를 넣으려면 , 카드에 표시된 화살 표가 하우징을 향하도록 마이크로 SD 카드를 맞춥니다 . 그림 3-13 을 참 조하십시오 .
PS4000 하드웨어 유지보수 제어 모듈 유지보수 5. 딸깍 소리가 날 때까지 카드를 몸체에 누릅니다 . 카드를 당겨 꺼낼 수 없 는지 확인합니다 . 그림 3-13: 마이크로 SD 카드 삽입 6. 제어 모듈을 설치합니다 . 3-13 페이지의 제어 모듈 설치하기 를 참조하 십시오 . 마이크로 SD 카드를 장착한 후 , 제어 모듈이 작동하는지 확인합니다 . 3-2 페이지의 제어 모듈 LEDs 해석 을 참조하십시오 .
4 전원 공급 장치 모듈 유지보수 배열에는 핫 스왑이 가능한 통합 전원 공급 장치 / 냉각 모듈 2 개가 포함되 어 있습니다 . LEDs 해석 그림 4-1 에서 제시하고 표 4-1 에서 설명한대로 전원 공급 장치 및 냉각 모 듈 LEDs 를 사용해 모듈 상태와 문제를 확인합니다 . 전원 공급 장치 및 냉각 모듈 LEDs 는 전원 , 팬 , 배열 상태를 보여줍니다 . 그림 4-1: 전원 공급 장치 및 냉각 모듈 LEDs 표 4-1: 전원 공급 장치 및 냉각 모듈 LEDs LED 색상 설명 꺼짐 정상 작동 . 주황색 DC 전원 오류 . 꺼짐 정상 작동 . 주황색 팬 오류 . 꺼짐 정상 작동 . 주황색 AC 전원 오류 . 꺼짐 전원이 들어오지 않음 . 녹색 정상 작동 . 오류 확인 다음의 특정 내용 또는 모든 내용으로 전원 공급 장치 및 냉각 모듈 오류를 확인할 수 있습니다 : • LEDs. 4-1 페이지의 LEDs 해석 을 참조하십시오 .
PS4000 하드웨어 유지보수 전원 공급 장치 모듈 유지보수 • 메시지 . 콘솔 , 이벤트 로그 또는 그룹 관리자 GUI 경보 패널에 표시된 메시지가 전원 공급 장치 / 냉각팬 모듈 오류를 설명합니다 . • 그룹 관리자 GUI 및 CLI 출력 . GUI 멤버 인클로저 창 또는 CLI 멤버 선택 보기 인클로저 명령은 전원 공급 장치 / 냉각 모듈 오류를 표시합니다 . 주: 배열의 후면을 보면 전원 공급 장치 0 은 오른쪽에 있고 전원 공급 장 치 1 은 왼쪽에 있습니다 . 자세한 설명은 1-2 페이지의 그림 1-3 을 참 조하십시오 . 전원 공급 장치 및 냉각 모듈 분리 전원 공급 장치 및 냉각 모듈이 고장난 경우 , 작동하는 모듈이 단 한 개만 있 어도 배열은 작동하지만 가능한 빨리 모듈을 교체해야 합니다 . 적절한 냉 각 기능이 수행될 수 있도록 , 교체 준비가 완료될 때까지 고장난 모듈을 분 리하지 마십시오 .
PS4000 하드웨어 유지보수 전원 공급 장치 모듈 유지보수 그림 4-2: 손잡이 분리 4. 손잡이를 잡고 모듈을 슬롯에서 주의하여 잡아 당깁니다 . 그림 4-3 을 참조하십시오 . 주의 : 모듈이 무겁습니다 . 양 손으로 잡으십시오 .
PS4000 하드웨어 유지보수 전원 공급 장치 모듈 유지보수 전원 공급 장치 및 냉각 모듈 설치 주의 : 모듈이 무겁습니다 . 양 손으로 잡으십시오 . 전원 공급 장치 및 냉각 모듈을 배열에 설치하려면 : 1. 1-5 페이지의 정전기 손목 보호대 사용 에 설명된대로 정전기 손목 보호 대를 부착합니다 . 2. 그림 4-2 를 다시 참조하십시오 . 래치를 안쪽으로 밀어넣어 (callout 1) 손잡이를 분리한 다음 , 손잡이를 위로 돌립니다 (callout 2). 3. 손잡이를 잡고 저항감이 느껴질 때까지 슬롯에 모듈을 밀어넣습니다 . 그림 4-4 를 참조하십시오 . 그림 4-4: 전원 공급 장치 및 냉각 모듈 설치 4. 손잡이가 래치에 끼워지고 모듈이 완전히 삽입될 때까지 손잡이를 아래 로 돌립니다 . 그림 4-2 를 다시 참조하십시오 . 5. 전원 케이블을 모듈에 연결합니다 . PS 시리즈 배열과 함께 전원 케이블 이 제공된 경우 , 해당 케이블을 이용하여 안전 요구사항을 충족합니다 .
PS4000 하드웨어 유지보수 주: 전원 공급 장치 모듈 유지보수 전원 케이블 구성을 위해 케이블 고정 완화 장치의 전선을 남겨두어 야 하는 경우 , 그림 4-5 에 보여진 대로 전선의 양끝을 함께 눌러서 전원 플러그 소켓에서 전선을 분리하십시오 . 전선을 반대로 뒤집은 후 다시 소켓에 연결합니다 . 그림 4-5: 케이블 고정 완화 장치 사용 7. 전원 공급 장치 및 냉각 모듈에 전원을 켭니다 . 일반적으로 초기화는 대 략 1 초에서 10 초 정도 걸립니다 . 초기화가 완료되면 , 전원 LED 가 녹색 이 되고 이벤트 메시지가 팬이 정상 속도로 회복되었음을 알려줍니다 . 8. 새로운 모듈이 작동 중인지 확인하고 , LEDs 에 빨간색이 없는지 확인합 니다 . 또한 , GUI 멤버 인클로저 창을 점검하거나 CLI 멤버 선택 보기 인 클로저 명령을 실행합니다 . 켜져있는 상태인지 확인합니다 .
PS4000 하드웨어 유지보수 4–6 전원 공급 장치 모듈 유지보수
A 환경 , 전원 및 기타 사양 Table A-2 는 PS4000 배열에 대한 환경 , 전원 , 물리적 사양을 설명합니다 . 표 A-2: PS4000 배열 사양 구성 요소 요구사항 완전 장착시 배열의 무게 35 kg (77.6 lb) 작동 온도 5 ~ 35 °C (41 ~ 95 °F) 보관 온도 -30 ~ 60 °C (-22 ~ 140 °F) 최대 작동 고도 3048 미터 (10,000 피트 ) 작동시 상대 습도 20% ~ 80% ( 비응축 ) 보관 상대 습도 5% ~ 80% ( 비응축 ) 열 방출 ( 최대 로딩 배열 ) 1700 BTU/hour (SAS 디스크 ) 1550 BTU/hour (SATA 디스크 ) 작동 충격 10ms 동안 5g 최대 1/2 사인 작동 진동 .
색인 L LEDs 냉각 모듈 4-1 네트워크 인터페이스 3-2 디스크 2-3 작동 패널 1-2 전원 공급 장치 4-1 제어 모듈 3-2 S SAS 디스크 지원 제어 모듈 3-1 확인 2-3 SATA 디스크 지원 제어 모듈 3-1 확인 2-3 V VLAN 권장사항 3-6 ᆨ 기가비트 이더넷 권장사항 3-5 ᆫ 냉각 LEDs 4-1 배열에 모듈 설치 4-4 배열에서 모듈 분리 4-2 작동 상태 확인 4-5 장애 표시 4-1 찾기 모듈 4-2 초기화 4-5 네트워크 가용성 향상 3-6 권장사항 3-5 성능 개선 3-5 성능 향상 3-6 연결 지침 3-5 장애 보호 3-4 최소 구성 3-6 케이블 연결 3-6 네트워크 인터페이스 LEDs 3-2 구성 3-5 연결 3-6 ᆮ 디스크 LEDs 2-3 SAS 2-1 SATA 2-1 배열에 설치 2-8 배열에서 분리 2-6 보호 2-4 장애 동작 2-5 장애 표시 2-5 제어 모듈 지원 2-1 찾기 2-5 취급 요구사항 2-4 타입 2-1 타입 확인 2-3
PS4000 하드웨어 유지보수 맴버 네트워크 연결 지침 3-5 다중 경로 I/O 권장사항 3-5 대역폭 증가 3-5 서브넷 액세스 권장사항 3-5 ᆸ 배열 LEDs 1-2, 2-3, 3-2, 4-1 냉각 4-1 네트워크 연결 지침 3-5 디스크 타입 2-3 방전 보호 1-5 시리얼 번호 1-2, 1-5 작동 상태 확인 2-9 장애 표시 1-2 전면 패널 1-1 전원 공급 장치 4-1 전지 3-1 제어 모듈 3-1 제어 모듈 제한 3-13 종료 절차 1-6 최소 네트워크 구성 3-6 팬 4-1 펌웨어 3-4 후면 패널 1-2 배열 종료 1-6 ᄉ 상태 제어 모듈 3-3 스위치 , 권장사항 VLAN 3-6 스패닝 트리 3-6 유니캐스트 폭주 제어 3-6 점보 프레임 3-6 흐름 제어 3-6 색인 -2 색인 스패닝 트리 권장사항 3-6 시리얼 번호 레이블 1-2, 1-5 ᄋ 요구사항 냉각 4-2 네트워크 3-6 디스크 2-4 배열 취급 1-5 전원 4-2 전원 케이블 4-4 제어 모듈 3-9 펌웨
PS4000 하드웨어 유지보수 전원 케이블 제한 4-4 케이블 고정 완화 장치 4-4 전지 서비스 3-1 충전 3-15 점보 프레임 권장사항 3-6 정전기 방전 방지 , 사용 1-5 제어 모듈 LEDs 3-2 동기화 3-9, 3-10 디스크 지원 3-1 마이크로 SD 카드 , 교체 3-4, 3-15 배열에서 분리 3-9 어레이에 설치 3-13 작동 상태 확인 3-14 장애 극복 동작 3-3 장애 표시 3-3 적절한 설치 확인 3-14 전지 3-1 종류 3-1, 3-13 지원 디스크 타입 3-13 찾기 3-3 취급 요구사항 3-9 캐시 전지 충전 3-15 펌웨어 요구사항 3-4, 3-13, 3-15 펌웨어 확인 3-4 혼합에 대한 제한 3-1, 3-13 색인 ᄏ 케이블 ( 네트워크 ), 연결 3-6 케이블 ( 전원 ), 연결 4-4 케이블 고정 완화 장치 , 사용 4-4 ᄐ 태그 , 시리얼 번호 1-2 ᄑ 팬 LEDs 4-1 배열에 모듈 설치 4-4 배열에서 모듈 분리 4-2 유지보수 4-1