PS4100 하드웨어 유지 관리 안내서 버전 1.
Copyright 2011 Dell, Inc. 저작권 본사 소유 . Dell 은 Dell, Inc 의 상표입니다 . EqualLogic 은 등록 상표입니다 . 본 지침에서 언급한 모든 상표 및 등록 상표는 각 소유자의 자산입니다 . 이 문서의 정보는 사전 통보 없이 변경될 수 있습니다 . Dell 의 서면 승인 없이 어떠한 방식으로든 본 자료를 무단 복제하는 행위는 엄격히 금지됩니다 .
차례 1 기본 스토리지 배열 정보 ......................................................................................................................... 1 주 , 주의 및 경고........................................................................................................................................................1 권장 도구....................................................................................................................................................................1 하드웨어 보호..........................
PS4100 하드웨어 유지 보수 안내서 차례 제어 모듈의 기능.....................................................................................................................................................17 제어 모듈 구성 정보............................................................................................................................................17 제어 모듈 LED 해석 ............................................................................................................................................18 제어 모듈 오류 식별...
PS4100 하드웨어 유지 보수 안내서 차례 배열 스타트 업 오류 문제 해결..............................................................................................................................36 통신 단절 문제 해결................................................................................................................................................36 배열 연결 문제 해결................................................................................................................................................36 외부 연결 문제 해결............
PS4100 하드웨어 유지 보수 안내서 vi 차례
1 기본 스토리지 배열 정보 이 장에는 사용자가 필요로 하는 스토리지 배열 , 도구 및 장비에서 교체 가능한 구성부품의 위치와 기본적인 작동 , 정전기 방전으로부터 하드웨어를 보호하는 방법 , 전원 켜기 및 끄기 작동에 관한 정보가 포함되어 있습니다 . 주 , 주의 및 경고 주는 시스템을 보다 효율적으로 사용하는데 도움이 되는 정보를 제공합니다 . 주의는 지침을 준수하지 않을 경우의 하드웨어 손상이나 데이터 손실 위험을 설명합니다 . 경고는 재산상의 피해나 심각한 부상 또는 사망을 유발할 수 있는 위험이 있음을 알려줍니다 . 권장 도구 이 항목의 절차를 수행하려면 다음 항목이 필요합니다 : • 베젤 키 • 손목 접지대 하드웨어 보호 정전기 방전으로부터 PS 시리즈 배열을 보호합니다 . 배열 하드웨어를 취급하는 경우 , 정전기 방지 용 손목 보호대나 이와 유사한 형태의 보호 장치를 사용하고 있는지 확인합니다 . 손목 보호대를 사용하려면 다음과 같이 합니다 : 1.
PS4100 하드웨어 유지 보수 안내서 기본 스토리지 배열 정보 섀시 종류 PS4100 배열은 2 가지 다른 종류의 섀시에서 사용이 가능합니다 : • 수직으로 설치된 24 개의 2.5 인치 드라이브가 포함된 2U 섀시 • 수평으로 설치된 24 개의 3.5 인치 드라이브가 포함된 4U 섀시 배열의 특성 배열에는 전면과 후면에 LED 및 기타 기능들이 구성되어 있습니다 . 베젤 베젤은 배열에 대한 실제적인 보호를 보장하기 위해 배열의 전면에 부착된 선택사양인 트림 (trim) 패널입니다 . 드라이브에 액세스하여 유지 관리하려면 베젤을 분리해야 합니다 . 베젤에는 배열 모델 번호를 확인할 수 있는 레이블이 있습니다 . 베젤 분리 베젤 제거 절차는 배열 모듈 설치 절차와 같습니다 . 1. 베젤 키를 사용하여 베젤의 잠금을 해제합니다 . 2. 베젤을 잡은 상태에서 베젤의 왼쪽에 있는 래치를 들어 올리고 배열의 왼쪽은 흔들리게 합니다 . 3. 베젤의 오른쪽을 들어 올려 배열의 오른쪽에서 분리합니다 . 4.
PS4100 하드웨어 유지 보수 안내서 기본 스토리지 배열 정보 그림 2 베젤 설치 전면 패널 기능 및 표시등 베젤이 분리된 상태에서 PS4100 의 전면이 그림 3 과 그림 4 에 제시되어 있습니다 . 표 1 은 전면 패널의 특징을 설명합니다 . 그림 3 전면 패널 기능 및 표시등 (3.5 인치 드라이브 ) 그림 4 전면 패널 기능 및 표시등 (2.
PS4100 하드웨어 유지 보수 안내서 기본 스토리지 배열 정보 표 1 전면 패널의 특징 설명 항목 표시등 1 배열 상태 LED 2 전원 LED 아이콘 설명 배열 전원이 켜진 경우 배열 상태 LED 가 켜집니다 . • 꺼짐 — 전원이 공급되지 않는 상태입니다 . • 파란색으로 켜져 있음 — 배열 상태가 양호합니다 . • 파란색으로 깜박거림 — 관리자에게 배열을 확인하도록 요청해 야 합니다 (Group Administration( 그룹 관리 ) 온라인 도움말 참조 ). • 황색으로 켜져 있음 — 치명적인 상태 . • 황색으로 깜박거림 — 경고 . 최소한 한 개의 전원 공급 장치가 배열에 전원을 공급하는 경우 전원 LED 가 켜집니다 . • 꺼짐 — 전원이 공급되지 않는 상태입니다 ( 전원 공급장치가 모 두 꺼져 있거나 존재하지 않습니다 ). • 녹색으로 켜져 있음 — 배열에 전원을 공급하는 최소 1 개의 전원 공급 장치가 있습니다 .
PS4100 하드웨어 유지 보수 안내서 기본 스토리지 배열 정보 표 2 배열의 후면 패널 특징 항목 기능 식별자 전원 스위치 ( 각각의 전 없음 원 공급 장치에 1 개 ) 전원 공급 장치 및 냉각 PSU0 ( 왼쪽 ) 팬 모듈 PSU1 ( 오른쪽 ) 1 2 타입 12 제어 모듈 3 CM0 ( 위쪽 ) CM1 ( 아래쪽 ) 제어 모듈 분리 레버 4 없음 설명 전원 스위치는 배열에 대한 전원 공급 장치 출력 을 제어합니다 . 700W 전원 공급 장치 자세한 내용은 29 페이지의 전원공급장치 LED 를 참조하십시오 . 제어 모듈은 다음을 제공합니다 : • 스토리지를 사용하는 배열과 응용 프로그램 간의 데이터 경로 • 배열에 대한 배열 관리 기능 배열에서 제어 모듈을 분리할 수 있습니다 . 배열 종료 및 재시작 PS 시리즈 배열에는 중복적이고 , 핫 스왑이 가능한 드라이브 , 전원 공급 장치 및 제어 모듈 ( 듀얼 제어 모듈 배열의 경우 ) 이 포함됩니다 .
PS4100 하드웨어 유지 보수 안내서 기본 스토리지 배열 정보 3. 다음과 같이 shutdown 명령을 입력합니다 . login: grpadmin Password: Welcome to Group Manager Copyright 2001-2011 Dell, Inc. group1> shutdown 직렬 연결에서 배열을 종료하는 경우에는 "press any key ( 아무 키나 누르십시오 )" 라는 메시지가 나 타날 때 전원을 끄는 것이 안전합니다 . ( 아무 키나 누르면 두 제어 모듈이 모두 재시작됩니다 .) 네트워크 연결을 사용하는 경우 , 배열이 완전히 종료되기 전에 세션의 연결이 끊어집니다 . 각각의 제 어 모듈의 ACT LED 가 어레이의 전원을 끄기 전에 꺼져 있는지 ( 점등되지 않은 상태 ) 확인합니다 . 배열 유지보수를 수행한 후 , 배열에 대한 전원을 끌 수 있습니다 . 배열 재시작이 완료되면 , 구성원 과 볼륨이 온라인 상태로 설정됩니다 .
2 드라이브 유지 보수 배열을 실행중인 상태에서 고장난 드라이브를 교체할 수 있습니다 . 드라이브 종류 사용자 구성에 따라서 , 배열은 내장형 드라이브 베이에서 최대 24 개의 2.5 인치 SAS 드라이브 또 는 최대 12 개의 3.5 인치 SAS 드라이브를 지원합니다 . 드라이브는 드라이브 캐리어를 통해 후면판에 연결되며 핫스왑이 가능합니다 . 드라이브는 특정 배열 모델에 적합하도록 열쇠가 잠긴 상태로 캐리어에 제공되며 , 다른 Dell 배열 또는 Dell Inc. 이 아닌 다른 업체의 배열에는 설치가 불가능합니다 . 고장난 드라이브 확인 드라이브 오류는 다음과 같이 표시됩니다 : • 드라이브의 LEDs. 드라이브 LED 해석을 참조하십시오 . • 콘솔 , 이벤트 로그 또는 그룹 관리자 경보 패널에 있는 표시되는 메시지 . • 그룹 관리자 구성요소 디스크 창 또는 CLI member select show disks ( 구성요소 선택 보기 디 스크 ) 명령 출력에서의 지시사항 .
PS4100 하드웨어 유지 보수 안내서 드라이브 유지 보수 드라이브 LED 해석 3.5 인치 드라이브에 있는 LED 는 그림 6 에 제시되어 있습니다 . 2.5 인치 드라이브에 있는 LED 는 그림 7 에 제시되어 있습니다 . 드라이브 LED 상태는 표 4 에 설명되어 있습니다 . 그림 6 3.5 인치 드라이브에 있는 LED 그림 7 2.
PS4100 하드웨어 유지 보수 안내서 드라이브 유지 보수 드라이브 고장시 배열의 동작 배열이 드라이브 오류를 처리하는 방식은 예비 드라이브의 이용 가능 여부와 고장난 드라이브를 포 함하고 있는 RAID 세트 성능의 저하 여부에 따라 달라집니다 . 예를 들면 다음과 같습니다 : • 예비 드라이브를 사용할 수 있는 경우 , 배열은 고장난 드라이브 교체를 위해 이러한 예비 드라 이브를 자동으로 사용합니다 . 재구성이 완료되면 성능은 정상이 됩니다 . • 예비 드라이브를 사용할 수 없는 경우 , RAID 세트의 성능이 저하될 수 있습니다 (RAID 6 세트 제외 ). 성능이 저하될 수 있습니다 . RAID 6 세트는 2 개의 드라이브가 동시에 고장난 경우에도 유지될 수 있습니다 . • 예비 드라이브를 사용할 수 없고 고장난 드라이브가 이미 성능이 저하된 RAID 세트에 위치하 는 경우 , 데이터 손실이 발생될 수 있으며 백업 드라이브에서 복구해야 합니다 . • 드라이브가 고장난 경우 , 교체하십시오 .
PS4100 하드웨어 유지 보수 안내서 드라이브 유지 보수 드라이브 설치 지침 및 제한 • 고장난 드라이브를 가능한 빨리 교체해 가장 높은 가용성을 제공하십시오 . • 유형 , 속도 , 스핀 속도가 동일한 드라이브만을 배열에 설치하십시오 . • 드라이브의 방향이 배열 모델에 대해 정확한 위치를 향하는지 확인하십시오 . 3 페이지의 전면 패널 기능 및 표시등을 참조하십시오 . • 동일한 배열에 용량이 다른 드라이브들을 사용할 수 있습니다 . 그러나 , 배열의 가장 작은 드라 이브가 각각의 드라이브에서 얼마나 많은 공간을 사용할 지 결정합니다 . 예를 들어 , 가장 작은 크기의 드라이브 용량이 400GB 인 경우 , 각각의 드라이브에서 사용 가능한 공간은 400GB 수준 입니다 . • 손잡이를 누르기 전에 드라이브가 섀시에 완전히 삽입되도록 합니다 . • 올바르게 설치된 경우 , 드라이브 높이가 배열 전면과 동일해집니다 . 드라이브가 배열에서 튀 어나온 경우 , 드라이브를 재설치하십시오 .
PS4100 하드웨어 유지 보수 안내서 드라이브 유지 보수 그림 8 2.5 인치 드라이브 분리 2.5 인치 드라이브 설치 2.5 인치 드라이브는 드라이브 분리 래치는 상단으로 그리고 드라이브 레이블은 하단을 향하게 하 여 수직으로 설치됩니다 . 1. 드라이브를 취급할 때 정전기 보호 장치를 착용하십시오 . 1 페이지의 하드웨어 보호를 참조하 십시오 . 2. 드라이브 분리 래치를 여십시오 . 3. 캐리어로 드라이브를 잡고 드라이브를 슬롯에 밀어넣습니다 ( 그림 9 에서 말풍선 1).
PS4100 하드웨어 유지 보수 안내서 드라이브 유지 보수 4. 드라이브를 슬롯에 완전히 눌러 넣습니다 ( 말풍선 2). 드라이브 핸들이 드라이브에서 닫히기 시 작합니다 ( 말풍선 3). 5. 짤깍하는 소리가 들릴 때까지 핸들을 누릅니다 ( 말풍선 4). 그림 9 2.5 인치 드라이브 설치 새 드라이브가 작동하는지 8 페이지의 드라이브 LED 해석에 설명된대로 전면 패널의 LED 를 검사 해 확인합니다 . 또한 , GUI 멤버 디스크 창과 CLI member select show disks ( 멤버 선택 보기 디스 크 ) 명령의 결과를 확인합니다 .
PS4100 하드웨어 유지 보수 안내서 드라이브 유지 보수 3.5 인치 드라이브 분리 1. 베젤을 분리합니다 . 2 페이지의 베젤 분리를 참조하십시오 . 2. 분리 단추를 누르십시오 ( 그림 10 에서 말풍선 1). 드라이브 래치가 열리고 드라이브가 배열에 서 일부 나타납니다 ( 말풍선 2). 3. 드라이브 베이에서 분리할 때까지 핸들로 드라이브를 잡아당겨 분리합니다 ( 말풍선 3). 그림 10 3.
PS4100 하드웨어 유지 보수 안내서 드라이브 유지 보수 3.5 인치 드라이브 설치 3.5 인치 드라이브는 드라이브 분리 래치는 왼쪽으로 그리고 드라이브 레이블은 오른쪽을 향하게 하여 수평으로 설치됩니다 . 1. 드라이브를 취급할 때 정전기 보호 장치를 착용하십시오 . 1 페이지의 하드웨어 보호를 참조하 십시오 . 2. 드라이브 분리 래치를 여십시오 . 3. 캐리어로 드라이브를 잡고 드라이브를 슬롯에 밀어넣습니다 ( 그림 11 에서 말풍선 1). 4. 드라이브를 슬롯에 완전히 눌러 넣습니다 ( 말풍선 2). 드라이브 핸들이 드라이브에서 닫히기 시 작합니다 ( 말풍선 3). 5. 짤깍하는 소리가 들릴 때까지 핸들을 누릅니다 ( 말풍선 4). 그림 11 3.
PS4100 하드웨어 유지 보수 안내서 드라이브 유지 보수 새 드라이브가 작동하는지 8 페이지의 드라이브 LED 해석에 설명된대로 전면 패널의 LEDs 를 검사 해 확인합니다 . 또한 , GUI 멤버 디스크 창과 CLI member select show disks ( 멤버 선택 보기 디스 크 ) 명령의 결과를 확인합니다 . 드라이브 보호물 설치 1. 베젤을 분리합니다 . 2 페이지의 베젤 분리를 참조하십시오 . 2. 드라이브 보호물이 완전히 장착될 때까지 드라이브 보호물을 드라이브 베이에 삽입합니다 . 3. 베젤을 부착합니다 . 드라이브 보호물 분리 경고 : 적절한 시스템 냉각을 유지하려면 모든 빈 드라이브 베이에 드라이브 보호물을 설치해야 합 니다 . 1. 베젤을 분리합니다 . 2 페이지의 베젤 분리를 참조하십시오 . 2. 분리 탭을 누르고 드라이브 보호물이 드라이브 베이에서 분리될 때까지 드라이브 보호물을 밉 니다 . 그림 12 또는 그림 13 을 참조하십시오 . 그림 12 3.
PS4100 하드웨어 유지 보수 안내서 드라이브 유지 보수 그림 13 2.
3 제어 모듈 유지 관리 다른 PS 시리즈 배열 모델에는 다른 유형의 제어 모델이 포함되어 있습니다 . 섀시 유형 , 제어 모듈 쌍 및 드라이브의 조합이 PS 시리즈 배열 모듈 번호를 결정합니다 . PS 시리즈 배열의 제어 모듈에는 Group Manager GUI( 그룹 관리자 GUI), Command Line Reference ( 명령 행 참조 ), 모든 배열 및 스토리지 관리 기능 및 특징을 제공하는 PS 시리즈 펌웨어가 포함되 어 있습니다 . 이상적으로 , 배열은 배열에 대한 단일 고장점의 발생을 피하기 위해 2 개의 모듈로 구성되어 있습 니다 ( 이러한 모듈은 동일한 유형이어야 합니다 ). PS4100 배열에는 1 개 또는 2 개의 핫스왑이 가능 한 타입 12 제어 모듈이 들어 있습니다 . 배열의 작동을 위해서는 정상적으로 기능을 수행하는 제어 모듈 1 개가 필요합니다 . 배열의 후면에 서 제어 모듈에 액세스할 수 있습니다 .
PS4100 하드웨어 유지 보수 안내서 제어 모듈 유지 관리 단일 컨트롤러 구성 단일 제어 모듈은 단일 고장점입니다 . 제어 모듈이 고장난 경우 , 전체 배열 ( 및 그러한 배열에 있 는 모든 볼륨 ) 을 사용할 수 없습니다 . Dell 은 2 개의 제어 모듈과 함께 배열을 구매하거나 단일 컨 트롤러 배열에 두번째 제어 모듈을 설치할 것을 강력하게 권장합니다 . 단일 제어 모듈이 있는 배열에서 , 모듈은 슬롯 CM0 에 있어야 합니다 . 주의 : 적절한 배열 냉각 및 기류 요구사항을 위해 , 빈 제어 모듈 슬롯에 보호물 필러가 있어야 합니 다. 듀얼 컨트롤러 구성 듀얼 제어 모듈 구성은 배열에서 단일 고장점을 제거합니다 . 활성 제어 모듈이 고장난 경우 , 서비 스 중단 없이 2 차 제어 모듈이 즉시 구축됩니다 . 이로써 사용자는 볼륨과 데이터에 계속해서 액세 스가 가능한 상태에서 고장난 제어 모듈을 교체할 수 있습니다 . 제어 모듈 LED 해석 제어 모듈에는 다음 LED 가 구성되어 있습니다 .
PS4100 하드웨어 유지 보수 안내서 제어 모듈 유지 관리 표 5 이더넷 및 관리 포트 LED 설명 LED 위치 상태 꺼짐 켜짐 Right( 오른쪽 ) 꺼짐 켜짐 Left( 왼쪽 ) 설명 전원이 공급되지 않거나 네트워크에 연결되지 않음 네트워크에 연결됨 전원이 공급되지 않음 , 전송 없음 또는 수신 없음 전송 중 또는 수신 중 표 6 제어 모듈 상태 LED 설명 LED 이름 상태 PWR 꺼짐 전원이 공급되지 않음 켜짐 ( 녹색으로 켜 전원이 공급됨 져 있음 ) 꺼짐 전원이 없는 2 차 제어 모듈은 활성 제어 모듈 또는 오류 상태 와 동기화되지 않습니다 . 녹색으로 켜져 있 활성 제어 모듈 ( 네트워크 I/O 기능 제공 ). 음 호박색으로 켜져 2 차 제어 모듈 . 캐시는 활성 제어 모듈과 동기화됩니다 . 있음 꺼짐 정상 작동 또는 전원이 공급되지 않음 적색으로 켜져 있 배열이 시작 중이거나 오류 상태임 음 빨간색으로 깜박거 배열이 전원 대기 모드에 있습니다 .
PS4100 하드웨어 유지 보수 안내서 제어 모듈 유지 관리 장애 조치 이해 듀얼 제어 모듈 배열에서 , 한번에 오직 1 개의 제어 모듈만이 활성화됩니다 ( 네트워크 소통량 관리 ). 각각의 제어 모듈에는 최근에 사용된 데이터를 저장하기 위한 캐시 - 플래시 모듈이 포함되 어 있습니다 . 중복성을 위해 2 차 제어 모듈의 캐시는 활성 제어 모듈의 캐시에 저장된 데이터를 미러링합니다 . 활성 제어 모듈은 2 차 제어 모듈에 있는 해당되는 포트에서 네트워크 스위치로 연결되는 케이블이 있는 경우 2 차 제어 모듈에 있는 네트워크 인터페이스를 사용할 수 있습니다 . 따라서 , 2 개의 제어 모듈 모두가 인터페이스에 액세스할 수 있도록 케이블을 각 제어 모듈의 모든 네트워크 인터페이스 포트에 연결해야 합니다 . 주 : 제어 모듈의 관리 포트들은 1 개의 제어 모듈이 고장난 경우 장애 조치가 적용되지 않습니다 .
PS4100 하드웨어 유지 보수 안내서 제어 모듈 유지 관리 배열에서 실행되고 있는 펌웨어 버전을 표시하려면 GUI 멤버 컨트롤러 창을 살펴보거나 다음의 CLI 명령을 사용하십시오 . member select show controllers microSD 카드의 펌웨어가 배열에서 실행되고 있는 펌웨어와 일치하지 않은 경우 펌웨어를 설치하 지 마십시오 . 대신 배열 지원 제공업체에 문의하십시오 . 제어 모듈 취급 요구 사항 이러한 제어 모듈 취급 요구사항을 따릅니다 : • 제어 모듈을 정전기 방전으로부터 보호하십시오 . 1 페이지의 하드웨어 보호에 설명된대로 제 어 모듈을 취급할 때에는 반드시 정전기 손목 보호대를 착용하십시오 . • 제어 모듈이 동기화되는 동안에는 배열에서 제어 모듈을 분리하지 마십시오 . 동기화가 완료되 면 콘솔 메시지가 표시됩니다 . 또한 , 2 차 제어 모듈의 ACT LED 가 주황색이 됩니다 . • 제어 모듈 슬롯을 비워 두지 마십시오 .
PS4100 하드웨어 유지 보수 안내서 제어 모듈 유지 관리 대기 단추 사용하기 기능이 그룹 전체에서 활성화되면 , 그룹 관리자 GUI 또는 CLI 를 사용하지 않고 신속하게 배열을 종료하기 위해 적용 가능한 멤버의 제어 모듈에 있는 대기 켜짐 / 꺼짐 단추를 사용할 수 있습니다 . 멤버를 대기 상태로 종료하려면 최소 2 초 동안 대기 켜짐 / 꺼짐 단추를 누른 상태로 있어야 합니다 . ( 배열을 완전히 종료하려면 , 전원 공급 장치와 냉각 모듈에 있는 스위치를 끄십시오 .) 멤버를 다시 켜려면 , ( 전원 공급 장치 스위치가 켜진 상태에서 ) 대기 켜짐 / 꺼짐 단추를 다시 누르 고 있으십시오 . 중요한 고려사항 그룹 관리자 GUI 또는 CLI 에 액세스 할 수 없는 상황에서 멤버를 신속하게 종료해야 하는 경우에 만 이 단추를 사용합니다 .
PS4100 하드웨어 유지 보수 안내서 제어 모듈 유지 관리 그렇지 않은 경우 , 가능하면 5 페이지의 배열 종료 및 재시작에 설명된 대로 모듈을 분리하기 전에 배열을 완전히 종료합니다 . 주의 : 제어 모듈이 동기화되는 동안에는 배열에서 제어 모듈을 분리하지 마십시오 . 동기화가 완료 되면 콘솔에 메시지가 표시됩니다 . 동기화가 완료되면 2 차 제어 모듈의 ACT LED 가 주황색이 됩 니다 . 제어 모듈 제거 제어 모듈을 분리하기 전에 : • 1 페이지의 하드웨어 보호에 설명된 대로 정전기 손목 보호대를 착용합니다 . • 제어 모듈에 연결된 직렬 또는 네트워크 케이블을 모두 분리합니다 . 선택적으로 , 네트워크 케 이블을 다른 제어 모듈에 다시 장착해 데이터 액세스를 연속으로 제공할 수 있습니다 . 제어 모듈을 분리하려면 다음을 수행하십시오 . 1. 주황색 분리 단추를 누르십시오 . 그림 16 을 참조하십시오 . 2.
PS4100 하드웨어 유지 보수 안내서 제어 모듈 유지 관리 제어 모듈 설치 배열을 종료하지 않은 상태에서 제어 모듈을 설치할 수 있습니다 . 주의 : 배열에 제어 모듈 종류를 혼합하여 사용하지 마십시오 . 제어 모듈이 이더넷 포트는 왼쪽에 그리고 직렬 포트는 오른쪽에 있는 상태로 배열에 수평으로 설 치됩니다 . 그림 17 을 참조하십시오 . 그림 17 올바른 제어 모듈 방향 배열의 후면을 위로 오게 한 상태에서 , 상단 제어 모듈은 CM0 이며 하단 제어 모듈은 CM1 입니다 . 제어 모듈을 설치하려면 다음을 수행하십시오 . 1. 정전기 손목 보호대나 유사한 보호 장치를 착용합니다 . 1 페이지의 하드웨어 보호를 참조하십 시오 . 2. 주황색 분리 탭을 누르고 검은색 레버는 분리되어 흔들리게 만듭니다 . 3. 저항감이 느껴질 때까지 제어 모듈을 섀시에 밀어 넣으십시오 . 그림 18 제어 모듈 설치 4. 검은색 레버를 안쪽으로 돌리고 제어 모듈이 슬롯에 완전히 삽입되도록 누릅니다 .
PS4100 하드웨어 유지 보수 안내서 제어 모듈 유지 관리 6. 배열이 종료되었으면 배열의 전원을 켭니다 . 7. 제어 모듈이 작동되는지 확인합니다 . 18 페이지의 제어 모듈 LED 해석을 참조하십시오 . 연결되면 , 제어 모듈 캐시 - 플래시 모듈이 완전히 충전됩니다 . 충전이 불가능한 경우 , 상태는 그룹 관리자 GUI 에서 BAD( 불량 ) 으로 보고됩니다 . 제어 모듈을 분리하고 다른 것으로 교체 해야 합니다 . 2 개의 제어 모듈이 설치되어 있지만 GUI 또는 CLI 에 1 개만 보여지는 경우 제어 모듈이 적절하 게 설치되지 않을 수 있습니다 . 제어 모듈을 다시 설치합니다 . 2 개의 제어 모듈 모두가 GUI 또 는 CLI 에 보여지지 않는 경우 동일한 펌웨어를 실행하지 않을 가능성이 있습니다 . 배열 지원 제공업체에 문의하십시오 . microSD 카드 장착 각각의 제어 모듈에는 PS 시리즈 펌웨어를 포함하는 microSD 카드가 있습니다 .
PS4100 하드웨어 유지 보수 안내서 제어 모듈 유지 관리 microSD 카드 분리 주의 : microSD 카드의 분실 또는 손상 위험을 줄이려면 , 교체용 제어 모듈에 설치할 준비가 될 때까 지 microSD 카드를 분리하지 마십시오 . 1. 카드를 카드 몸체로 단단히 밀어 스프링 장치를 분리합니다 ( 그림 19). microSD 카드의 일부가 몸체에서 나옵니다 . 그림 19 microSD 카드 꺼내기 2. 카드를 몸체에서 조심스럽게 똑바로 위로 잡아 당깁니다 . 3. microSD 카드를 정전하 보호가 되는 평평한 표면에 놓습니다 .
PS4100 하드웨어 유지 보수 안내서 제어 모듈 유지 관리 microSD 카드 삽입 1. 교체용 microSD 카드를 맞춰 카드에 있는 화살표가 몸체 ( 그림 20) 를 가리키도록 합니다 . 2. 딸깍 소리와 함께 제자리에 고정될 때까지 카드를 몸체에 단단히 누릅니다 . 카드를 당겨 꺼낼 수 없는지 확인합니다 . 그림 20 microSD 카드 삽입 3. 배열에 제어 모듈을 설치합니다 . 24 페이지의 제어 모듈 설치를 참조하십시오 . 4. 제어 모듈이 작동되는지 확인합니다 . 18 페이지의 제어 모듈 LED 해석을 참조하십시오 .
PS4100 하드웨어 유지 보수 안내서 제어 모듈 유지 관리 고급 네트워킹 옵션 2 개의 제어 모듈에 있는 모든 이더넷 포트를 네트워크 스위치에 연결하는 것 이외에 , 선택사양으 로 관리 포트를 개별 네트워크 스위치에 연결할 수 있습니다 . 관리 포트를 구성하면 iSCSI 데이터 트래픽 ( 응용프로그램과 볼륨 간의 I/O 및 복제 파트너 간의 I/O) 에서 관리 트래픽 ( 그룹 , 멤버 , 볼륨 , 복제 등의 생성 및 관리 ) 을 구분할 수 있습니다 . 관리 포트 구성 10/100Mbps 관리 포트를 구성하는 과정에는 하드웨어 절차와 소프트웨어 절차가 수반됩니다 . 관 리 포트는 그룹 관리 트래픽으로 제한됩니다 . 관리 포트는 iSCSI I/O 를 전달하지 않습니다 . 주 : 이는 사용자의 환경이 이러한 수준의 보안을 요구하는 경우 사용 가능한 고급 구성으로 간주됩 니다 . 하드웨어 절차 1.
4 전원 공급 장치 및 냉각 모듈 유지 관리 배열은 핫 스왑이 가능한 통합 전원 공급 장치 및 냉각 모듈 2 개를 지원할 수 있습니다 . 배열은 1 개 의 모듈만으로 일시적으로 작동이 가능하지만 , 배열의 장기간 냉각을 위해서는 2 개의 모듈이 모두 존재해야 합니다 . AC 전원 공급 장치 정보 PS 시리즈 배열은 2 개의 전원 공급 장치와 냉각 모듈 (PSUs) 로부터 A/C 전원을 공급받습니다 . 배열을 서늘한 상태로 유지시켜주는 팬이 전원 공급 모듈에 통합되어 있지만 개별적으로 교체가 불 가능합니다 . 팬이 고장난 경우 , 전체 전원 공급 장치 모듈을 교체해야 합니다 . PS4100 에는 700 Watt PSU 가 2 개입니다 . 각각의 700W 전원 공급 장치에는 2 개의 냉각 팬이 포함 되어 있습니다 . 전원공급장치 LED 전원 공급 장치 및 냉각 모듈에는 상태를 제시해주는 LED 가 포함되어 있습니다 . 그림 21 및 표 7 을 참조하십시오 .
PS4100 하드웨어 유지 보수 안내서 전원 공급 장치 및 냉각 모듈 유지 관리 표 7 전원공급장치 LED 설명 항목 LED 색상 상태 1 녹색 켜짐 (ON) — 정상 작동 . 전원 공급 장치가 AC 전원에 연결되어 있고 전원 스위치가 켜져 있습니다 . 전원 공급 장치 모듈이 배열에 DC 전원을 공급하 고 있습니다 . DC 전원 다음 중 하나에 해당되면 꺼짐 (OFF): • 전원 스위치가 꺼져 있습니다 . • 전원 공급 장치가 AC 전원에 연결되어 있지 않습니다 . • 장애 상태가 존재합니다 . 2 장애 경고 또는 치명적인 수준의 장애 목록은 Group Administration ( 그룹 관리 ) 설명서를 참조하십시오 . 호박색 켜짐 — 장애가 확인됨 . 꺼짐 — 정상 . 처음 전원 공급 장치 모듈의 전원을 켜면 짧게 깜박거림 . 3 AC 전원 녹색 경고 또는 치명적인 수준의 장애 목록은 Group Administration ( 그룹 관리 ) 설명서를 참조하십시오 .
PS4100 하드웨어 유지 보수 안내서 전원 공급 장치 및 냉각 모듈 유지 관리 4. 오른손으로 핸들을 잡고 엄지손가락을 사용하여 주황색 분리 래치를 오른쪽으로 밀어내십시오 . 5. 모듈을 슬롯에서 잡아당겨 분리합니다 . 그림 22 를 참조하십시오 . 주의 : 모듈이 무겁습니다 . 양 손으로 잡으십시오 . 그림 22 전원 공급 장치 및 냉각 모듈 분리 전원 공급 장치 및 냉각 모듈 설치 1. 주황색 분리 래치가 왼쪽 상단에 위치하도록 전원 공급 장치를 잡으십시오 . 2. 전원 공급 장치 및 냉각 모듈이 섀시에 완전히 장착되고 분리 래치가 딸깍하는 소리가 날 때까 지 밉니다 . 그림 23 을 참조하십시오 . 주 : 전원 케이블을 연결하기 전에 , 팬이 스피닝을 시작하며 이는 다른 전원 공급 장치 모듈에 의 해 전원을 공급받습니다 .
PS4100 하드웨어 유지 보수 안내서 전원 공급 장치 및 냉각 모듈 유지 관리 그림 23 전원 공급 장치 및 냉각 모듈 삽입 3. 전원 스위치가 꺼짐 (OFF) 위치에 있는지 확인하십시오 . 4. 전원 케이블을 전원 공급 장치 및 냉각 모듈에 연결하고 케이블을 전원 콘센트에 연결합니다 . 주 : AC 전원 케이블이 연결되면 전원 공급 장치에 있는 스위치가 꺼진 경우에도 AC LED 가 점 등됩니다 . 5. 훅 앤 루프 패스너 스트랩을 사용하여 전원 케이블을 단단히 고정합니다 . 그림 24 를 참조하십 시오 .
PS4100 하드웨어 유지 보수 안내서 전원 공급 장치 및 냉각 모듈 유지 관리 그림 24 전원 케이블 고정 6. 전원 공급 장치와 냉각 모듈에 있는 스위치를 켭니다 .
PS4100 하드웨어 유지 보수 안내서 34 전원 공급 장치 및 냉각 모듈 유지 관리
5 배열 문제 해결 안전 제일 — 사용자 및 배열을 위함 대부분의 수리 작업은 공인된 서비스 기술자만 수행할 수 있습니다 . 사용자는 제품 설명서에서 허 가한 경우나 온라인 또는 전화서비스 / 지원팀에서 지시한 경우에만 문제 해결 절차 및 단순 수리 작 업을 수행할 수 있습니다 . Dell 의 승인을 받지 않은 서비스 작업으로 인한 손상에 대해서는 보상을 받을 수 없습니다 . 제품과 함께 제공된 안전 지침을 읽고 따르십시오 . 기술 지원 및 고객 서비스 얻기 Dell 지원 서비스는 PS 시리즈 SAN 배열 질문에 대한 답변을 제공합니다 . 전화를 걸어 문의하기 전 에 특급 서비스 코드를 알아둡니다 . Dell 자동 응답 지원 전화 시스템은 이 코드를 사용하여 보다 효 율적으로 고객의 전화 문의를 처리합니다 . Dell 에 문의하기 Dell 은 다양한 온라인 및 전화 기반의 지원과 서비스 옵션을 제공합니다 .
PS4100 하드웨어 유지 보수 안내서 배열 문제 해결 구성부품 진단 프로그램 얻기 그룹 관리자 GUI 또는 CLI 를 통해 PS 시리즈 그룹의 1 개 이상의 구성요소에 대한 진단 정보를 수 집할 수 있습니다 . 자세한 정보는 Group Administration ( 그룹 관리자 ) 안내서 또는 CLI Reference 안 내서를 참조하십시오 . 배열 스타트 업 오류 문제 해결 시스템이 스타트 업 과정에서 중단되는 경우 , 다음을 확인하십시오 : • 배열 오류 LED 가 점등됩니다 . 1 페이지의 하드웨어 보호를 참조하십시오 . • 하드 드라이브에 액세스할 때 지속적으로 긁히거나 삐걱거리는 이상한 소리가 들립니다 . 35 페 이지의 기술 지원 및 고객 서비스 얻기를 참조하십시오 . 통신 단절 문제 해결 통신 단절 문제 해결에 관한 정보는 배열에 대한 설치 안내서에서 네트워크 요구사항 및 권장사항 을 참조하십시오 . 배열 연결 문제 해결 1.
PS4100 하드웨어 유지 보수 안내서 배열 문제 해결 전원 공급 장치 및 냉각 모듈 문제 해결 1. 결함이 있는 전원 공급 장치를 찾고 LED 의 상태를 확인합니다 . AC 전원 LED 가 켜지지 않는 경우 , 전원 공급 장치가 연결된 전원 코드 및 전원을 확인합니다 . – 다른 장치를 전원에 연결해 전원이 정상 작동하는지 확인합니다 . – 케이블을 다른 전원에 연결합니다 . – 전원 케이블을 교체하십시오 . 문제가 해결되지 않은 경우 또는 전원 공급 장치의 장애 표시등이 점등된 경우 , 35 페이지의 기 술 지원 및 고객 서비스 얻기를 참조하십시오 . 전원 공급 장치 및 냉각 모듈은 핫 스왑이 가능합니다 . 배열은 전원 공급 장치 하나를 사용하여 작동할 수 있습니다 . 그러나 , 적절한 냉각을 위해 두 개의 모듈을 모두 설치해야 합니다 . 전원 이 공급된 배열에서 하나의 전원 공급 장치 및 냉각 모듈을 최대 5 분 정도 분리할 수 있습니다 .
PS4100 하드웨어 유지 보수 안내서 배열 문제 해결 제어 모듈 문제 해결 1. 제어 모듈을 제거하고 후면판과 제어 모듈에 있는 핀이 구부러지지 않은 상태인지 확인합 니다 . 22 페이지의 제어 모듈 교체를 참조하십시오 . 2. 컨트롤 모듈을 다시 설치하고 30 초 동안 대기하십시오 . 22 페이지의 제어 모듈 교체를 참조하 십시오 . 3. 제어 모듈 상태 LED 를 검사하십시오 . 자세한 내용은 18 페이지의 제어 모듈 LED 해석을 참조 하십시오 . 4. 제어 모듈 상태 LED 가 호박색으로 깜박이는 경우 ( 순서 당 5 회 ), 제어 모듈의 모든 펌웨어를 지원되는 최신 펌웨어로 업데이트하십시오 . 최신 펌웨어 다운로드에 관한 자세한 내용은 PS 시 리즈 발행 정보와 PS 시리즈 스토리지 배열 펌웨어 업데이트 문서를 참조하십시오 . 이러한 자 료는 고객 지원 사이트에서 제공받을 수 있습니다 . 5.
색인 LED 장애 동작 ...................................... 9 네트워크 인터페이스 .................18 장애 표시 ...................................... 7 제어 모듈 .....................................18 찾기 ............................................... 7 LEDs 디스크 ............................................8 MicroSD 카드 취급 요구사항 .............................. 9 문제 해결 ....................................... 35 냉각 문제 .................................... 37 분리 ..............................................26 스타트업 오류 ..........
PS4100 하드웨어 유지 보수 안내서 색인 배열 종료 .........................................5 네트워크 연결 ............................ 20 베젤 제어 모듈 .................................... 20 분리 ................................................2 베젤 , 설치 .......................................2 보안 ................................................35 분리 전면 패널 기능 ............................................... 3 전원 공급 장치 분리 ............................................. 30 3.5 인치 드라이브 .................10, 13 전원 표시등 ..................
PS4100 하드웨어 유지 보수 안내서 색인 취급 요구 사항 ............................21 펌웨어 버전 .................................20 펌웨어 요구 사항 ........................20 혼합에 대한 제한 ........................24 팬 분리 ..............................................30 펌웨어 버전 확인 .....................................21 요구 사항 .....................................20 펌웨어 버전 식별 ..........................21 표시등 전원 ................................................