PS4110 Speicherarrays Hardware-Benutzerhandbuch Version 1.
Copyright 2011 Dell Inc. Alle Rechte vorbehalten. Dell und EqualLogic sind Marken von Dell Inc. Alle in diesem Dokument genannten Marken und eingetragenen Marken sind das Eigentum ihrer jeweiligen Besitzer. Die in diesem Dokument enthaltenen Informationen können sich ohne vorherige Ankündigung ändern. Die Vervielfältigung oder Wiedergabe dieser Materialien in jeglicher Weise ohne vorherige schriftliche Genehmigung von Dell Inc. sind strengstens untersagt.
Inhaltsverzeichnis 1 Grundlegende Informationen zum Speicherarray Anmerkungen, Vorsichtshinweise und Warnungen Empfohlene Werkzeuge Gehäusetypen Array – Merkmale und Funktionen Anzeigen und Funktionen auf der Rückseite Herunterfahren und Neustarten eines Arrays 2 Wartung der Laufwerke Laufwerktypen Identifizieren von fehlerhaften Laufwerken Bedeutung der Laufwerk-LEDs Arrayverhalten bei Laufwerkfehlern Richtlinien für die Handhabung von Laufwerken Anweisungen und Beschränkungen für den Laufwerkeinbau 3 Wa
1 Grundlegende Informationen zum Speicherarray Dieses Kapitel enthält Informationen über die Position und den grundlegenden Betrieb der austauschbaren Komponenten in einem Speicherarray, benötigte Tools und Geräte, Schutz der Hardware vor elektrostatischen Entladungen und Anweisungen zum Ein- und Ausschalten. Anmerkungen, Vorsichtshinweise und Warnungen Eine ANMERKUNG macht auf wichtige Informationen aufmerksam, mit deren Hilfe Sie den Computer besser einsetzen können.
Hardware-Benutzerhandbuch 1 Grundlegende Informationen zum Speicherarray Schutz der Hardware Schützen Sie PS Series-Arrays vor elektrostatischer Entladung. Achten Sie bei der Handhabung der ArrayHardware darauf, stets eine elektrostatische Erdungsmanschette zu tragen oder eine ähnliche Form von Schutzeinrichtung zu verwenden. So verwenden Sie eine Erdungsmanschette: 1. Verbinden Sie die Stahlklammer am Spiralkabel mit dem Stift am Gummiband. Siehe Abbildung 1. Abbildung 1: Erdungsmanschette verwenden 2.
Hardware-Benutzerhandbuch 1 Grundlegende Informationen zum Speicherarray Die Blende Die Blende ist eine optionale, an der Arrayvorderseite angebrachte Verkleidung, um das Array vor Beschädigungen zu schützen. Für den Zugang und die Wartung der Laufwerke muss die Blende entfernt werden. Auf der Blende befindet sich ein Etikett mit der Array-Modellnummer. Entfernen der Blende Die Schritte für die Installation der Blende sind für alle Array-Modelle identisch. 1.
Hardware-Benutzerhandbuch 1 Grundlegende Informationen zum Speicherarray Abbildung 2: Installieren der Blende Funktionen und Anzeigen des vorderseitigen Bedienfeldes Abbildung 3 und Abbildung 4 zeigen die Vorderseite eines PS4110 ohne die Blende. Tabelle 1 sind die Funktionen des vorderseitigen Bedienfeldes beschreiben.
Hardware-Benutzerhandbuch 1 Grundlegende Informationen zum Speicherarray Tabelle 1: Beschreibungen der Merkmale des vorderseitigen Bedienfeldes Element Anzeige Symbol Beschreibung 1 Array-Status-LED 2 Betriebsanzeige-LED Die Status-LED des Arrays leuchtet, wenn die Stromversorgung des Arrays eingeschaltet ist. • Aus – Kein Strom. • Stetig blau – Arraystatus ist OK. • Langsam blau blinkend – Arraystatus ist Standby-Modus.
Hardware-Benutzerhandbuch 1 Grundlegende Informationen zum Speicherarray Tabelle 2: Funktionsmerkmale der Array-Rückseite Element Funktion Kennung Beschreibung 1 Netzschalter Keine Der Netzschalter schaltet die Stromversorgung des Gehäuses ein und aus. Einer auf jedem Netzteil. 2 Netzteileinheit (PSU) 3 Controller 4 Entriegelungshebel für Keine Controller PSU0 (links) PSU1 (rechts) CM0 (oben) CM1 (unten) Netzteil-/Lüftermodul für Array.
Hardware-Benutzerhandbuch 1 Grundlegende Informationen zum Speicherarray 2. Melden Sie sich bei einem Benutzerkonto mit Lese-/Schreibzugriff an, etwa grpadmin. 3. Geben Sie wie dargestellt den Befehl shutdown ein. login: grpadmin Password Welcome to Group Manager Copyright 2001-2008 Dell Inc. group1> shutdown Wenn Sie ein Array über eine serielle Verbindung herunterfahren, können Sie nach der Anzeige „press any key“ (drücken Sie eine beliebige Taste) die Stromversorgung ausschalten.
2 Wartung der Laufwerke Ein ausgefallenes Laufwerk kann bei weiterlaufendem Array ausgetauscht werden. Laufwerktypen Je nach der Art Ihrer Konfiguration unterstützt das Array bis zu 24 2,5-Zoll-SAS-Laufwerken oder bis zu 12 3,5-Zoll-SAS-Laufwerken in internen Laufwerkschächten. Die Laufwerke werden über Laufwerksträger mit einer Rückwandplatine verbunden und sind hot-swap-fähig.
Hardware-Benutzerhandbuch 2 Wartung der Laufwerke Tabelle 3: Nummerierung der 3,5-Zoll-Laufwerke 0 1 2 3 4 5 6 7 8 9 10 11 Bedeutung der Laufwerk-LEDs Die LEDs von 3,5-Zoll-Laufwerken werden in Abbildung 6 gezeigt. Die LEDs von 2,5-Zoll-Laufwerken werden in Abbildung 7 gezeigt. Der Zustand der Laufwerks-LEDs wird in Tabelle 4 beschrieben.
Hardware-Benutzerhandbuch 2 Wartung der Laufwerke Tabelle 4: Zustände der Laufwerk-LEDs Beschreibung Laufwerks-Aktivitätsanzeige (ACT-LED) Laufwerks-Statusanzeige (PWR-LED) Anzeigenzustände Grün blinkend: Laufwerksaktivität Stetig grün: Keine Laufwerksaktivität Grün: Laufwerk OK Gelb: Laufwerk ausgefallen Aus: Laufwerk ohne Stromversorgung Arrayverhalten bei Laufwerkfehlern Wie ein Array mit einem Laufwerksausfall umgeht, hängt davon ab, ob ein Ersatzlaufwerk verfügbar ist und ob der RAID-Satz mit de
Hardware-Benutzerhandbuch 2 Wartung der Laufwerke • Lassen Sie die Laufwerke vor dem Einbau sich auf Raumtemperatur erwärmen. Lassen Sie beispielsweise ein Laufwerk über Nacht akklimatisieren, bevor Sie es in einem Array installieren. • Lassen Sie Laufwerkschachte nicht unbelegt. In jedem Laufwerkssteckplatz eines Arrays müssen eine Laufwerkseinheit oder ein Platzhalter installiert sein. Wenn Sie ein Array mit einem leeren Laufwerksteckplatz betreiben, erlöschen die Garantie und der Wartungsvertrag.
Hardware-Benutzerhandbuch 2 Wartung der Laufwerke • Es besteht eine zweiminütige Verzögerung zwischen dem Zeitpunkt des Einsetzens eines Laufwerks und der automatischen Konfiguration in einem RAID-Satz. Dieses Zeitintervall ermöglicht die gleichzeitige Konfiguration von mehreren Laufwerken in einem Array; dies ist effizienter, als ein einzelnes Laufwerk zu installieren, zu konfigurieren und dann den Vorgang zu wiederholen. Wenn Sie zum Beispiel ein Laufwerk einsetzen, wird der Zeitgeber gestartet.
Hardware-Benutzerhandbuch 2 Wartung der Laufwerke Abbildung 8: Entfernen eines 2,5-Zoll-Laufwerks Installieren eines 2,5-Zoll-Laufwerks Die 2,5-Zoll-Laufwerke werden senkrecht installiert, mit der Entriegelungsvorrichtung des Laufwerks nach oben und der Laufwerkbeschriftung nach unten. 1. Tragen Sie beim Handhaben eines Laufwerks elektrostatischen Schutz. Lesen Sie Schutz der Hardware auf Seite 2. 2. Öffnen Sie die Entriegelungsvorrichtung für das Laufwerk.
Hardware-Benutzerhandbuch 2 Wartung der Laufwerke 3. Fassen Sie das Laufwerk am Träger an und schieben Sie es fast vollständig in einen Laufwerkschacht hinein (Erklärung 1 in Abbildung 9). 4. Schieben Sie das Laufwerk vollständig in den Schacht (Erklärung 2). Der Laufwerkbügel beginnt sich über dem Laufwerk zu schließen (Erklärung 3). 5. Drücken Sie den Bügel auf das Laufwerk, bis Sie ein Klicken hören (Erklärung 4).
Hardware-Benutzerhandbuch 2 Wartung der Laufwerke Entfernen eines 3,5-Zoll-Laufwerks 1. Entfernen Sie die Frontblende. Siehe Entfernen der Blende auf Seite 3. 2. Drücken Sie die Entriegelungstaste (Erklärung 1 in Abbildung 10). Die Laufwerkverriegelung öffnet sich und das Laufwerk wird ein Stück aus dem Array herausgeschoben (Erklärung 2). 3. Ziehen Sie das Laufwerk am Griff heraus, bis es vollständig aus dem Laufwerkschacht entfernt ist (Erklärung 3).
Hardware-Benutzerhandbuch 2 Wartung der Laufwerke Installieren eines 3,5-Zoll-Laufwerks Die 3,5-Zoll-Laufwerke werden waagerecht installiert, mit der Entriegelungsvorrichtung des Laufwerks auf der linken Seite und der Laufwerkbeschriftung auf der rechten Seite. 1. Tragen Sie beim Handhaben eines Laufwerks elektrostatischen Schutz. Lesen Sie Schutz der Hardware auf Seite 2. 2. Öffnen Sie die Entriegelungsvorrichtung für das Laufwerk. 3.
Hardware-Benutzerhandbuch 2 Wartung der Laufwerke Abbildung 11: Installieren eines 3,5-Zoll-Laufwerks Prüfen Sie, ob das neue Laufwerk betriebsbereit ist, indem Sie die LEDs des vorderseitigen Bedienfeldes ansehen, wie unter Bedeutung der Laufwerk-LEDs auf Seite 10 beschrieben. Überprüfen Sie darüber hinaus das GUI-Fenster „Member Disks“ (Mitgliedslaufwerke) und die Ausgabe des CLI-Befehls member select show disks.
Hardware-Benutzerhandbuch 2 Wartung der Laufwerke Entfernen eines Laufwerkplatzhalters Warnung: Um eine ausreichende Systemkühlung zu gewährleisten, müssen alle leeren Laufwerkschächte mit entsprechenden Platzhaltern belegt sein. 1. Entfernen Sie die Frontblende. Siehe Entfernen der Blende auf Seite 3. 2. Drücken Sie die Entriegelungslasche und ziehen Sie den Laufwerkplatzhalter ganz aus dem Laufwerkschacht heraus. Siehe Abbildung 12 oder Abbildung 13.
Hardware-Benutzerhandbuch 2 Wartung der Laufwerke Installieren eines Laufwerkplatzhalters 1. Entfernen Sie die Blende. Siehe Entfernen der Blende auf Seite 3. 2. Schieben Sie den Platzhalter in den Laufwerkschacht, bis er vollständig eingesetzt ist. 3. Befestigen Sie die Blende.
3 Warten von Controllern Die verschiedenen PS Series-Array-Modelle enthalten gegebenenfalls verschiedene Typen von Controllern. Die Kombination aus Gehäusetyp, Controllerpaar und Laufwerken bildet die Modellnummer eines PS Series-Arrays. Die Controller in einem PS Series-Array enthalten die PS Series-Firmware, welche die grafische Benutzeroberfläche von Group Manager, die Befehlszeile und alle Array- und Speicherverwaltungsfunktionen bereitstellt.
Hardware-Benutzerhandbuch 3 Warten von Controllern • Eine vor Ort austauschbare MicroSD-Karte mit der PS-Series-Firmware Die MicroSD-Karte ist von der Rückseite des Controllers aus zugänglich. • Eine Entriegelungstaste und einen Riegel, um der Controller für einen Austausch aus dem Array zu entnehmen. Der Entriegelungshebel ist mit einem Schalter versehen, der die Betätigung erkennt und das Array veranlasst, die Daten in einem nicht-flüchtigen Speicher zu speichern, um sie zu schützen.
Hardware-Benutzerhandbuch 3 Warten von Controllern Abbildung 14: Empfohlene Netzwerkkonfiguration zur Unterstützung von vertikalem Failover Anmerkung: Falls an einem der Controller ein Netzwerkport für Failover verfügbar ist, aber derzeit nicht verwendet wird, leuchten seine LEDs nicht. Bedeutung der Controller-LEDs Auf den Controllern befinden sich folgende LED-Anzeigen: • Die Ethernet-Ports und der Verwaltungs-Port verfügen jeweils über zwei LEDs, die den Status und die Aktivität der Ports anzeigen.
Hardware-Benutzerhandbuch 3 Warten von Controllern Tabelle 5: Beschreibungen der LEDs der Ethernet-Ports und des Verwaltungsports 10GBASE-T-Ethernet LED-Position Links (Link) Rechts (Act) SPF+ Ethernet LED-Position Oben (Link) Unten (Act) Verwaltung LED-Position Links (Link) Rechts (Act) Zustand Beschreibung Aus Ein Aus Ein Kein Strom, keine Netzwerkverbindung oder passiv. Netzwerkverbindung. Kein Strom, kein Senden oder kein Empfang. Senden oder Empfangen.
Hardware-Benutzerhandbuch • 3 Warten von Controllern Ausgabe der Group Manager-GUI und -CLI. Das Fenster „Member Controllers“ (Mitgliedscontroller) bzw. der CLI-Befehl member select show controllers zeigen den Status des Controllers als not installed (nicht installiert) an. Von der Rückseite des Arrays aus gesehen, befindet sich CM0 oben und CM1 unten. Siehe Funktionen und Anzeigen des vorderseitigen Bedienfeldes auf Seite 4.
Hardware-Benutzerhandbuch 3 Warten von Controllern Wartung der Firmware des Controllers Ein Controller verfügt über eine MicroSD-Karte, auf der die Firmware läuft. Sie sollten die aktuellste Firmwareversion einsetzen, um neue Produktfunktionen und -verbesserungen nutzen zu können. Vorsichtshinweis: Bei einem Array mit zwei Controllern müssen beide Controller über die gleiche Firmwareversion verfügen; andernfalls funktioniert nur ein Controller.
Hardware-Benutzerhandbuch 3 Warten von Controllern Die Taste STANDBY ON/OFF Die Kontrollermodule vom Typ 17 verfügen über einen kleine versenkt angeordnete Taste, die mit „Standby ON/OFF“ beschriftet ist (siehe Abbildung 16). Diese Taste ist versenkt angebracht, um eine versehentliche Betätigung zu vermeiden. Abbildung 16: Position der Standby-Taste Aktivieren der Standby-Funktion Um die Standby-Taste zu verwenden, muss ein Gruppenadministrator die Funktion in der Group Manager-GUI oder -CLI aktivieren.
Hardware-Benutzerhandbuch 3 Warten von Controllern Um das Mitglied wieder einzuschalten, halten Sie die „Standby On/Off“-Taste erneut gedrückt (wenn die Netzschalter eingeschaltet sind). Wichtige Überlegungen Verwenden Sie diese Taste nur, wenn Sie in Situationen, in denen Sie keinen Zugriff auf die Group ManagerGUI oder -CLI haben, schnell ein Mitglied herunterfahren müssen.
Hardware-Benutzerhandbuch 3 Warten von Controllern Vorsichtshinweis: • Entfernen Sie keinen aktiven Controller. • Entfernen Sie einen Controller nicht während der Synchronisierung der Controller aus einem Array. Eine Konsolenmeldung informiert über den Abschluss der Synchronisierung. Die ACT-LED am sekundären Controller leuchtet orange, wenn die Synchronisierung abgeschlossen ist. • Um eine ausreichende Kühlung zu gewährleisten, darf ein Controllerschacht nicht leer bleiben.
Hardware-Benutzerhandbuch 3 Warten von Controllern Ersetzen des aktiven Controllers Verwenden Sie einen der folgenden Vorgänge, um den aktive Controller im Array zu ersetzen: • Array mit einem Controller: 1. Fahren Sie das System vollständig herunter. (Wie in Herunterfahren und Neustarten eines Arrays auf Seite 6 beschrieben.) 2. Ersetzen Sie den Controller. (Wie unter Ersetzen des sekundären Controllers auf Seite 29 beschrieben.) • Array mit zwei Controllern: 1.
Hardware-Benutzerhandbuch 3 Warten von Controllern Entfernen eines Controllers Entfernen eines Controllers: • Lesen Sie die Informationen am Beginn von Austauschen eines Controllers auf Seite 28. • Legen Sie eine Erdungsmanschette an. Lesen Sie Schutz der Hardware auf Seite 2. • Ziehen Sie alle seriellen Kabel und Netzwerkkabel vom Controller ab.
Hardware-Benutzerhandbuch 3 Warten von Controllern 3. Legen Sie den Controller auf einer ebenen Fläche mit Schutz vor elektrostatischer Ladung ab. Legen Sie nichts auf den Controller, um Schäden zu vermeiden. 4. Wenn Sie ein ausgefallener Controller ersetzen, entfernen Sie die MicroSD-Karte aus dem defekten Controller und installieren Sie sie im neuen Controller. Damit ist sichergestellt, dass das neue Controller mit der richtigen Firmware betrieben wird. Siehe Austauschen der MicroSD-Karte auf Seite 34.
Hardware-Benutzerhandbuch 3 Warten von Controllern Abbildung 19: Installieren eines Controllers (2U-Array) 4. Drehen Sie den Hebel (Erklärung 2) nach innen, wodurch der Controller vollständig in den Schacht hineingezogen wird. Der Riegel des Hebels rastet an der vorgesehenen Stelle ein. 5. Schließen Sie die Netzwerkkabel wieder an. 6. Schalten Sie dann die Stromversorgung des Arrays ein, falls sie ausgeschaltet war. 7. Stellen Sie sicher, dass das Array funktionsfähig ist.
Hardware-Benutzerhandbuch 3 Warten von Controllern Austauschen der MicroSD-Karte Jeder Controller enthält eine MicroSD-Karte mit der PS Series-Firmware. Wenn ein Controller ausfällt, entfernen Sie die MicroSD-Karte aus dem fehlerhaften Controller und installieren Sie sie in dem Ersatzmodul. Dadurch wird sichergestellt, dass im neuen Steuermodul die gleiche Firmware wie im anderen Controller des Arrays ausgeführt wird.
Hardware-Benutzerhandbuch 3 Warten von Controllern Abbildung 20: Auswerfen der MicroSD-Karte 2. Ziehen Sie die Karte vorsichtig und gerade aus der Halterung heraus. 3. Legen Sie die MicroSD-Karte auf eine ebene Fläche mit Schutz vor elektrostatischer Ladung. Einsetzen der MicroSD-Karte 1. Halten Sie die MicroSD-Karte so, dass der Pfeil auf der Karte Richtung Gehäuse zeigt (Abbildung 21). Bei korrekter Positionierung zeigen die Goldkontakte nach unten und nach innen in Richtung Gehäuse. 2.
Hardware-Benutzerhandbuch 3 Warten von Controllern Abbildung 21: Einsetzen der MicroSD-Karte 3. Installieren des Controllers im Array. Siehe Installieren eines Controllers auf Seite 32. 4. Stellen Sie sicher, dass der Controller funktionsfähig ist. Siehe Bedeutung der Controller-LEDs auf Seite 23.
Hardware-Benutzerhandbuch 3 Warten von Controllern Konfigurieren des Verwaltungs-Ports Das Konfigurieren des 10/100-Mbit/s-Verwaltungsports umfasst Hardware- und Software-Schritte. Der Verwaltungsport kann nur Datenverkehr zur Gruppenverwaltung übertragen; er kann keine iSCSI-E/A-Daten übertragen. Anmerkung: Sie können diese erweiterte Konfiguration verwenden, wenn Ihre Umgebung dieses Maß an Sicherheit erfordert. Hardware-Schritte 1.
4 Wartung von Netzteil- und Lüftermodulen Das Array unterstützt zwei hot-swap-fähige Netzteil- und Lüftermodule. Das Array kann nur kurzzeitig mit einem Modul betrieben werden, für den Dauerbetrieb müssen jedoch beide Kühlmodule vorhanden sein. Über Netzteile Das PS Series-Array wird von zwei Netzteilen (PSUs) mit Strom versehen. Jedes PSU hat ein Netzteil von 700W. Jedes 700-W-Netzteil verfügt über zwei Kühllüfter.
Hardware-Benutzerhandbuch 4 Wartung von Netzteil- und Lüftermodulen Abbildung 23: 700W-Stromversorgungs-LEDs Tabelle 7: Beschreibung der Stromversorgungs-LEDs Element LED Farbe Zustand EIN – Normaler Betrieb. Die Stromversorgung ist mit dem Stromnetz verbunden und der Netzschalter ist eingeschaltet. Die Stromversorgung versorgt das Array mit Gleichstrom. 1 Gleichstrom AUS, wenn eine der folgenden Situationen vorliegt: • Der Netzschalter ist ausgeschaltet.
Hardware-Benutzerhandbuch 4 Wartung von Netzteil- und Lüftermodulen Netzteil-/Lüftermodul entfernen Wenn ein Netzteil- und Lüftermodul ausfällt, müssen Sie es so schnell wie möglich ersetzen, wenngleich ein Array auch mit nur einem intakten Modul funktioniert. Um eine ausreichende Kühlung des Arrays zu gewährleisten, entfernen Sie ein ausgefallenes Modul erst unmittelbar vor dem Einsetzen des Ersatzgeräts.
Hardware-Benutzerhandbuch 4 Wartung von Netzteil- und Lüftermodulen Abbildung 24: Netzteil-/Lüftermodul entfernen Netzteil- und Lüftermodul installieren Verwenden Sie die folgenden Schritte mit den zugehörigen Abbildungen, um ein Netzteil- und Lüftermodul zu entfernen: 1. Halten Sie das Netzteilmodul so, dass sich die orange Freigabevorrichtung oben links befindet. 2.
Hardware-Benutzerhandbuch 4 Wartung von Netzteil- und Lüftermodulen Abbildung 25: Einsetzen eines Netzteil-/Lüftermodule 3. Stellen Sie sicher, dass sich der Netzschalter in der Stellung OFF (AUS) befindet. 4. Verbinden Sie das Stromversorgungskabel mit dem Netzteil- und Lüftermodul und schließen Sie das Kabel an einer Steckdose an. Anmerkung: Die Wechselstrom-LED leuchtet auf, wenn das Netzkabel angeschlossen wird, auch wenn die Netzschalter des Netzteils ausgeschaltet sind. 5.
Hardware-Benutzerhandbuch 4 Wartung von Netzteil- und Lüftermodulen Abbildung 26: Sichern der Netzstromkabel 6. Schalten Sie die Schalter des Netzteil- und Lüftermoduls ein.
5 Fehlerbehebung am Array Sicherheit geht vor – für Sie und das Array Viele Reparaturarbeiten dürfen nur von zugelassenen Servicetechnikern durchgeführt werden. Sie sollten nur die Behebung von Störungen sowie einfache Reparaturen unter Berücksichtigung der jeweiligen Angaben in den Produktdokumentationen von Dell durchführen, bzw. die elektronischen oder telefonischen Anweisungen des Service- und Supportteams von Dell befolgen.
Hardware-Benutzerhandbuch 5 Fehlerbehebung am Array So finden Sie die Service-Tag-Nummer Jedes Array hat eine Service-Tag-Nummer. Diese Informationen werden gegebenenfalls vom Kundendienst benötigt, wenn Sie sich an ihn wenden. • Der Aufkleber mit der Service-Tag-Nummer ist auf der Vorderseite des sichtbar, auf dem rechten Block zur Blendenverriegelung.
Hardware-Benutzerhandbuch 5 Fehlerbehebung am Array Fehlerbehebung bei externen Verbindungen • Überprüfen Sie, ob alle Kabel an die richtigen Ethernet- und gegebenenfalls Management-Ports angeschlossen sind, bevor Sie eine Fehlerbehebung an externen Geräten durchführen. Den Standort der Rückwandplatinenanschlüsse auf Ihrem Array ersehen Sie aus Anzeigen und Funktionen auf der Rückseite auf Seite 5. • Stellen Sie sicher, dass die Stromkabel korrekt an die Netzteile Ihres Arrays angeschlossen sind.
Hardware-Benutzerhandbuch 5 Fehlerbehebung am Array Fehlerbehebung bei Array Kühlungsproblemen Überprüfen Sie die folgenden Sachverhalte und korrigieren Sie sie gegebenenfalls: • Leere Laufwerkschächte (kein Laufwerk oder Platzhalterlaufwerk). • Die Umgebungstemperatur ist zu hoch. Überprüfen Sie die Technische Daten für das Array im Installations- und Setup-Handbuch. • Der externe Luftstrom ist gestört. • Das Netzteil-/Lüftermodul wurde entfernt oder ist defekt.
Hardware-Benutzerhandbuch 5 Fehlerbehebung am Array Fehlerbehebung bei Laufwerken Überprüfen Sie die Anzeigen der Laufwerke, bevor Sie das fehlerhafte Laufwerk aus dem Array entfernen. 1. Entfernen Sie das Laufwerk aus dem Array. Siehe Entfernen eines 2,5-Zoll-Laufwerks auf Seite 13 und Entfernen eines 3,5-Zoll-Laufwerks auf Seite 16. 2. Überprüfen Sie das Laufwerk, um sicherzustellen, dass die Anschlüsse nicht beschädigt sind. 3. Setzen Sie das Laufwerk wieder ein. 4.
Stichwortverzeichnis E A Anforderungen Controller Firmware Kühlung Laufwerke Strom 26 26 41 11 41 Ein Array herrunterfahren Elektrostatische Entladung, vermeiden Elektrostatische Erdungsmanschette, verwenden Empfohlene Werkzeuge Entfernen 3,5-Zoll-Laufwerk Platzhalterkarte 6 2 2 1 13, 16 19 Anzeigen Strom 4 F Array Controller Controllerbeschränkungen Firmware Kühlung LEDs Lüfter Stromversorgungen Vorgang des Herunterfahrens 21 32 26 39 10, 23 39 39 6 Ausfallsanzeichen Controller Laufwerke 24 9 e
Stichwortverzeichnis: Lüfter – Stromversorgung Laufwerke Netzwerkschnittstellen 10 23 Lüfter Entfernen des PSU 41 M Micro-SD-Karte Firmware 26 MicroSD-Karte einsetzen entfernen ersetzen 35 34 26 N Netzwerk Ausfallschutz 25 Netzwerkschnittstellen LEDs 23 P PS Series-Array Schutz vor dem Entladen 2 S Sicherheit Status 45 Controller 24 Stromversorgung Entfernen 52 41