저작권 2008 Dell, Inc. 저작권 본사 소유 . Dell 은 Dell, Inc. 의 상표입니다 . EqualLogic 은 등록 상표입니다 . 본 지침에서 언급한 모든 상표 및 등록 상표는 각 소유자의 자산입니다 . 이 문서의 정보는 사전 통보 없이 변경될 수 있습니다 . Dell 의 서면 승인 없이 어떠한 경우에도 무단 복제하는 것을 엄격히 금합니다 . 2008 년 12 월 부품번호 : P631M-KO Rev. 1.
Table of Contents 서문 ............................................................................................................v 수용자 ...................................................................................................................v 구성 .......................................................................................................................v 설명서 ..................................................................................................................
설치 및 구성 Table of Contents 3 단계 : 소프트웨어 구성 시작 ........................................................................ 3-4 설치 유틸리티를 사용하여 소프트웨어 구성하기.................................. 3-4 소프트웨어 구성을 위해 원격 설치 마법사 사용하기............................ 3-7 4 단계 : 멤버 RAID 정책 설정 ......................................................................... 3-8 RAID 정책 설정을 위해 CLI 사용하기 .................................................... 3-8 GUI 를 사용하여 RAID 정책 설정............................................................
서문 스토리지 배열이 PS 시리즈 1 개 이상인 경우 , 크기에 관계없이 1 개의 PS 시 리즈그룹 즉 , 적절한 가격에 사용이 간편한 자체 관리형 iSCSI 스토리지 영 역 네트워크 (SAN) 를 생성할 수 있습니다 . 이 설명서에는 PS6000 및 PS6500 배열 하드웨어 설치 , 소프트웨어 구성 , SAN 사용 시작 방법이 설명되어 있습니다 . 수용자 본 설명서는 배열 하드웨어 설치 담당 관리자용으로 고안되었습니다 . 관리 자가 네트워크 또는 스토리지 시스템에 대해 포괄적인 경험을 가지고 있을 필요가 없습니다 .
설치 및 구성 서문 설명서 배열 , 그룹 , 볼륨에 대한 PS 시리즈 세부 정보는 아래의 설명서를 참조하십 시오 : • PS 시리즈 발행 정보 . 배열 및 그룹에 대한 PS 시리즈 최신 정보를 제 공합니다 . • Dell EqualLogic PS Series Array 최종 사용자 라이센스 계약 (EULA) • 보증 및 지원 정보 (WSI) • 안전 , 환경 지침 및 규정 정보 (SERI) • PS 시리즈 하드웨어 유지보수 . 배열 하드웨어의 유지보수 방법을 설명 합니다 . 배열 모델에 대한 설명서를 사용하십시오 . • PS 시리즈 그룹 관리 . 그룹 PS 시리즈 관리를 위해 그룹 관리자 그래 픽 사용자 인터페이스 (GUI) 를 사용하는 방법을 설명합니다 . 이 설명 서는 제품 개념과 절차에 대한 포괄적인 정보를 제공합니다 . • PS 시리즈 CLI 참조 . 그룹 및 개별 배열 PS 시리즈 관리를 위해 그룹 관리자 명령 행 인터페이스 (CLI) 를 사용하는 방법을 설명합니다 .
설치 및 구성 서문 Dell 사에 문의하기 Dell 은 다양한 온라인 및 전화 기반의 지원과 서비스 옵션을 제공합니다 . 제 공 여부는 국가 / 지역과 제품에 따라 차이가 있으며 일부 서비스는 소재 지 역에서 사용하지 못할 수 있습니다 . 미국 고객의 경우 800-945-3355 로 전화하십시오 . 주 : 인터넷 연결을 사용할 수 없는 경우에는 제품 구매서 , 포장 명세서 , 청 구서 또는 Dell 제품 카탈로그에서 연락처 정보를 찾을 수 있습니다 . 판매 , 기술 지원 또는 고객 서비스 문제에 대해 Dell 에 문의하려면 : 1. support.dell.com 을 방문합니다 . 2. 창 하단의 Choose A Country/Region ( 국가 / 지역 선택해주세요 ) 드롭다 운 메뉴에서 한국을 선택합니다 . 3. 창 왼쪽에서 Contact Us ( 문의하기 ) 를 클릭합니다 . 4. 필요에 따라 해당 서비스 또는 지원 링크를 선택합니다 . 5. Dell 에 문의하는 데 편리한 방법을 선택합니다 .
설치 및 구성 • support.dell.com/EqualLogic • support.jp.dell.com ( 일본 전용 ) • support.euro.dell.
1 시작을 위한 단계별 과정 SAN 을 설치하고 배열 사용을 시작하려면 다음 단계를 따르십시오 : 1. PS 시리즈 배열 하드웨어의 구성 설치 . 본 설명서에는 PS 시리즈 배열을 네트워크 및 전원에 연결하는 것에 대한 정보가 포함되어 있습니다 . 2 장 , 하드웨어 설치를 참조하십시오 . 2. PS 시리즈 소프트웨어 구성 . 우선 , 네트워크에서 액세스가 가능하도록 배열을 초기화합니다 . 그 다음 , 첫번째 그룹 멤버로서 배열과 함께 그룹 을 생성하거나 기존 그룹에 배열을 추가합니다 . 그룹을 확장하면 , 용량 과 성능도 자동으로 증가됩니다 . 다음과 같은 2 가지 방법으로 소프트웨어를 구성할 수 있습니다 . Windows 컴퓨터를 사용하고 있고 요구사항이 충족되는 경우, 원격 설치 마법사를 사용합니다 . 설치 유틸리티는 모든 환경에서 지원됩니다 . 3 장 , 소프트웨어 구성을 참조하십시오 . 3. SAN 의 사용 시작 . 볼륨을 생성하여 그룹 스토리지 공간을 사용자와 응 용프로그램에 할당합니다 .
2 하드웨어 설치 PS 시리즈 배열 사용에서 1 단계는 하드웨어를 설치하는 것입니다 . 본 장에 는 다음과 같은 일반 정전기 방지 및 네트워크 정보와 , PS6000 및 PS6500 배 열에 대한 설치 정보가 포함되어 있습니다 . • 2-1 페이지의 하드웨어 보호 • 2-2 페이지의 네트워크 요구사항 및 권장사항 • 2-4 페이지의 배열 PS6000 설치 • 2-13 페이지의 배열 PS6500 설치 배열 하드웨어를 설치하면 3 장 , 소프트웨어 구성에 설명된대로 소프트웨 어를 구성할 수 있습니다 . 하드웨어 보호 정전기 방전으로부터 PS 시리즈 배열을 보호합니다 . 배열 하드웨어를 취급 할 경우 , 배열과 함께 제공된 정전기 손목 보호대 또는 유사한 보호 수단을 사용해야 합니다 . 손목 보호대를 사용하려면 : 1. 코일 코드의 강철 스냅을 탄력 밴드의 스터드에 연결합니다 . 그림 2-1 을 참조하십시오 . 그림 2-1: 정전기 손목 보호대 사용 2.
네트워크 요구사항 및 권장사항 설치 및 구성 네트워크 요구사항 및 권장사항 PS 시리즈 배열에 대한 최소 네트워크 구성은 각각의 제어 모듈에 있는 이더 넷 0 과 컴퓨터 또는 네트워크 스위치 간의 연결로 구성됩니다 . 성능 및 가용 성 증대를 위해 배열에 다수의 네트워크 인터페이스를 구성하고 이러한 인 터페이스를 다수의 스위치에 연결합니다 . 네트워크 권장사항은 표 2-1 에 설명되어 있습니다 . 또한 , 적절한 네트워크 구성을 위한 모든 일반 규칙들이 PS 시리즈 배열에 적용됩니다 . 일반적인 네트워크 구성은 이 설명서의 적용범위를 벗어난 주제입니다 . 표 2-1: 네트워크 권장사항 권장사항 설명 교환 기가비트 이더넷 배열 및 컴퓨터를 교환 네트워크에 연결하고 컴퓨터와 배열 네트워크 간의 모든 네트워크 연결이 기가비트 이더넷이 되도록 합니 다 . 배열은 10 또는 100 메가비트에서 작동되지만 , 기가비 트 이더넷 스위치를 사용할 경우 성능이 저하됩니다 .
네트워크 요구사항 및 권장사항 설치 및 구성 표 2-1: 네트워크 권장사항 ( 계속 ) 권장사항 설명 엔드 노드를 연결하는 가능한 경우 , 엔드 노드를 연결하는 스위치 포트에 스패닝 스위치 포트에 STP 기 트리 프로토콜 (STP) 을 사용하지 마십시오 (iSCSI 초기자 또는 배열 네트워크 인터페이스 ). 능이 없습니다 . 그러나 , STP 또는 RSTP (STP 보다 선호됨 ) 를 사용해야 하 는 경우 , 링크시 상태를 전달하는 STP 로 포트를 즉시 변화 시키는 ( 몇몇 스위치에서 사용 가능한 ) 포트 설정을 활성화 시켜야 합니다 . 이 기능을 사용하면 장치를 재시작할 때 발 생되는 네트워크 간섭을 줄일 수 있으므로 이 기능은 엔드 노드를 연결하는 스위치 포트에서만 활성화시켜야 합니다 . 스위치 간의 단일 케이블 연결에는 스패닝 트리를 사용할 수 있으며 , 스위치 간의 다중 케이블 연결에는 트렁킹을 사 용할 수 있습니다 .
배열 PS6000 설치 설치 및 구성 배열 PS6000 설치 PS600016 개의 드라이브 슬롯이 있는 3U 배열 , 전원 공급 장치 2 개 , 냉각 모듈 , 컨트롤 모듈 2 개가 있는 경우 , 본 설명서를 사용합니다 . 그림 2-2: PS6000 배열 - 전면 모습 그림 2-3: PS6000 배열 - 후면 모습 시작하기 전에 PS6000 배열 설치를 시작하기 전에 이러한 필수 조건을 충족시켜야 합니다 : • 배열 및 설치 장소가 환경 요구조건에 부합되는지 확인합니다 . 2-5 페이 지의 환경 요구 사항 을 참조하십시오 . • 필요한 모든 하드웨어를 준비합니다 . 2-6 페이지의 배송상자 내용물 및 필요한 하드웨어 를 참조하십시오 . • 배열을 랙에 설치합니다 . 2-7 페이지의 랙 장착 요구사항 을 참조하십시 오.
배열 PS6000 설치 설치 및 구성 환경 요구 사항 PS6000 배열에 대한 이러한 환경 요구 사항을 충족해야 합니다 . • 전압 범위가 100-240 VAC 전원에서만 인클로저를 작동합니다 . • 전원이 전기 과부하 보호가 충분한지 확인합니다 . • 배열 전면과 후면에 기류 공간을 충분히 확보합니다 . • 설치 장소가 환풍이 잘 되는지 확인합니다 . • 표 2-2 에 대한 기술 사양을 검토하여 환경이 요구사항에 부합하도록 합 니다 . 표 2-2: PS6000 기술 사양 구성 요소 요구사항 완전 장착시 배열의 무게 77.
배열 PS6000 설치 설치 및 구성 배송상자 내용물 및 필요한 하드웨어 표 2-3 에 설명된 항목이 배송상자에 모두 포함되어 있는지 확인합니다 . 사 용자의 환경에 특이적이고 배송상자에 포함되어 있지 않은 추가 하드웨어 를 제공해야 합니다 . 표 2-4 를 참조하십시오 . 표 2-3: PS6000 배송상자 내용물에 대한 설명 구성 요소 설명 3U 배열 섀시 PS6000 배열에는 두 개의 종류 7 제어 모듈이 포함되어 있 습니다 ( 녹색 페이스 플레이트 및 이더넷 포트 4 개 ). 종류 7 제어 모듈 전원 케이블 직렬 케이블 4- 폴 랙을 위한 레일 조립품 키트 . 정전기 손목 보호대 설명서 2–6 배열에는 전원 공급 장치 및 냉각 모듈 2 개 , 직렬 연결된 SCSI (SAS) 디스크 또는 직렬 ATA (SATA) 디스크인 디스크 8 개 또는 16 개가 포함되어 있습니다 . 배열을 전원에 연결합니다 .
배열 PS6000 설치 설치 및 구성 표 2-4: 필요한 하드웨어 – 제공되지 않음 구성 요소 설명 표준 19 인치 . 4 폴 (four-pole) 랙 컴퓨터 사용 환경에서 배열과 다른 하드웨어에 간편하게 액 세스할 수 있도록 지원합니다 . 네트워크 케이블 2-8 개 배열을 네트워크 스위치에 연결합니다 . RJ45 커넥터와 함께 Category 5E 또는 Category 6 케이블을 사용합니다 . TIA/EIA TSB95 표준에 부합되는 경우에만 Category 5 케이블을 사용합니다 . 각 제어 모듈의 적어도 하나의 포트를 네트워크 스위치에 연 결합니다 . 네트워크 스위치 네트워크에 장치를 연결합니다 . 다중 스위치가 권장됩니다 . 무정전 전원 공급 장치 (UPS) 또한 선택적으로 사용하여 배열에 가용성 높 은 (highly available) 전원을 제공할 수 있습니다 .
설치 및 구성 배열 PS6000 설치 2. 배열을 네트워크에 연결하십시오 . 2-9 페이지의 2 단계 : 배열을 네트워 크에 연결 을 참조하십시오 . 3. 배열의 전원을 켜십시오 . 2-11 페이지의 3 단계 : 배열 전원 켜기 를 참조 하십시오 . 4. 소프트웨어 구성을 위해 설치 유틸리티를 사용할 계획이라면 , 2-11 페이 지의 4 단계 : 배열에 직렬 연결 설정 을 참조하십시오 . 소프트웨어 구성을 위해 원격 설치 마법사를 사용할 계획이라면 , 이 단 계를 건너뛰십시오 . 다음 섹션에는 각각의 설치 단계가 상세히 설명되어 있습니다 . 하드웨어 설 치를 완료하였으면 3 장 , 소프트웨어 구성을 참조하십시오 . 1 단계 : 전원에 배열 연결 PS6000 배열에는 전원 및 냉각 기능을 모두 제공하는 2 개의 모듈이 포함되 어 있습니다 . 배열의 작동을 위해서는 전원 공급원에 연결된 1 개의 기능적 전원 공급 장치 및 냉각 모듈이 필요합니다 . 배열과 함께 제공되는 전원 케이블을 준비합니다 .
배열 PS6000 설치 설치 및 구성 그림 2-4: 권장 전원 구성 - PS6000 2 단계 : 배열을 네트워크에 연결 PS6000 배열에는 동일한 종류 및 색상의 제어 모듈이 2 개 포함되어 있습니 다 . 각 제어 모듈에는 0-3 까지 표시된 4 개의 네트워크 인터페이스 포트가 있습니다 . 배열의 작동을 위해서는 기능적 네트워크 연결 1 개가 필요합니다 . 성능 및 높은 가용성을 고려하여 다중 네트워크 연결이 권장됩니다 . 추가적인 네트 워크 권장사항은 표 2-1 을 참조하십시오 . 네트워크 케이블을 2-8 개 준비합니다 . 네트워크 케이블은 배열 배송상자에 포함되어 있지 않습니다 . 제공된 네트워크 케이블 종류는 표 2-4 를 참조하 십시오 . 최소한 2 개의 제어 모듈에 있는 이더넷 0 에 네트워크 케이블을 연결한 후 케이블을 네트워크 스위치에 연결해야 합니다 . 그림 2-5 를 참조하십시오 .
배열 PS6000 설치 설치 및 구성 그림 2-5: 최소 네트워크 구성 - PS6000 최대 네트워크 대역폭 및 가용성을 위해 , 8 개의 네트워크 케이블을 사용하 여 모든 네트워크 인터페이스를 다중 네트워크 스위치에 연결할 것을 권장 합니다 . 스위치는 대역폭이 충분한 상호스위치 링크와 함께 연결해야 합니 다 . 그림 2-6 을 참조하십시오 .
배열 PS6000 설치 설치 및 구성 3 단계 : 배열 전원 켜기 전원을 켜기 전에 , PS6000 이 주변 온도에 적응하도록 충분한 시간을 둡니 다 ( 예 : 하룻밤 ). 각 전원 공급 장치 및 냉각 모듈에서 전원 스위치는 전원 플러그 아래에 있습 니다 . 주 : 전원이 켜지면 , 전지가 충전되기 시작하고 일부 하드웨어 구성부품이 동기화되기 시작합니다 . 배열 LEDs 는 배열의 동작이 정상 수준인 이 러한 현재의 작동 상태를 표시합니다 . 4 단계 : 배열에 직렬 연결 설정 소프트웨어를 구성하기 위해 설치 유틸리티를 사용할 계획이라면 , 직렬 연 결을 구성해야 합니다 . 원격 설치 마법사를 사용할 계획이라면 , 직렬 연결 이 필요하지 않습니다 . 원격 설치 마법사 요구사항에 대한 정보는 3-1 페이 지의 1 단계 : 구성 방법 선택 을 참조하십시오 . 주 : 배열과 제공된 직렬 연결 케이블은 양쪽에 DB9 암 (female) 커넥터가 있 는 ( 그림 2-7) 표준 널 모뎀 케이블입니다 .
배열 PS6000 설치 설치 및 구성 표 2-5: DB9 에서 DB9 핀아웃 정보 ( 계속 ) DB9-1 기능 DB9-2 핀 핀 5 5 시스템 접지 데이터 세트 준비 + 캐리어 감지 6+1 4 데이터 터미널 준비 전송 요청 7 8 송신 준비 완료 송신 준비 완료 8 7 전송 요청 시스템 접지 기능 활성 제어 모듈 (ACT LED 가 녹색 ) 직렬 포트 및 콘솔 터미널 또는 터미널 에뮬레이터 실행 컴퓨터에 케이블을 장착합니다 . 그림 2-8 을 참조하십시오 ( 실물 크기와 다를 수 있습니다 ).
배열 PS6500 설치 설치 및 구성 직렬 연결은 다음과 같은 특성을 가지고 있어야 합니다 : • 9600 보드 • • 1 개의 STOP 비트 패리티 없음 • 데이터 비트 : 8 • 흐름제어 없음 주 : 직렬 케이블을 보관합니다 . 네트워크 액세스가 없는 경우 , 직렬 케이 블을 사용하여 그룹 또는 특정 배열을 관리해야 합니다 . 하드웨어 설치를 완료하였으면 3 장 , 소프트웨어 구성을 참조하십시오 . 배열 PS6500 설치 PS6500 48 개의 드라이브 슬롯이 있는 4U 인 배열 , 전원 공급 장치 및 냉각 모듈 3 개 , 컨트롤러 모듈 2 개가 있는 경우 , 본 설명서를 사용합니다 .
배열 PS6500 설치 설치 및 구성 시작하기 전에 PS6500 배열 설치를 시작하기 전에 이러한 필수 조건을 충족해야 합니다 : • 배열 및 설치 장소가 환경 요구조건에 부합되는지 확인합니다 . 2-14 페 이지의 환경 요구 사항 을 참조하십시오 . • 필요한 모든 하드웨어를 준비합니다 . 2-15 페이지의 배송상자 내용물 및 필요한 하드웨어 를 참조하십시오 . • 배열을 랙에 설치합니다 . 2-17 페이지의 랙 장착 요구사항 을 참조하십 시오 . 환경 요구 사항 PS6500 배열에 대한 이러한 환경 요구 사항을 충족해야 합니다 . • 전압 범위가 100-240 VAC 전원에서만 인클로저를 작동합니다 . • 전원이 전기 과부하 보호가 충분한지 확인합니다 . • 북아메리카에서는 더블 폴 20A 미만으로 제공되는 과전류 방지 전원 공 급 장치에 인클로저를 연결합니다 (LISTED 회로 차단기 -UL489).
배열 PS6500 설치 설치 및 구성 표 2-6: PS6500 기술 사양 ( 계속 ) 구성 요소 요구사항 열 방출 ( 최대 로딩 배열 ) 3400 BTU/hour 작동 충격 10ms 경우 , 5g 최대 1/2 사인 작동 진동 0.21grms 5-500 Hz 랜덤 입력 전압 100-240 VAC ( 자동 감지 ) 입력 주파수 50-60 Hz 시스템 입력 전원 1400 VA ( 최대 ) 각 전원 공급 장치 440 watts DC 출력 최대 입력 전원 : 0.7 KVA 입력 전류 : 7-3.5 A 크기 6.89 인치 . x 19.01 인치 . x 31.9 인치 . (17.5 cm x 48.3 cm x 81.0 cm) 배송상자 내용물 및 필요한 하드웨어 표 2-7 에 설명된 항목이 배송상자에 모두 포함되어 있는지 확인합니다 . 사 용자의 환경에 특이적이고 배송상자에 포함되어 있지 않은 추가 하드웨어 를 제공해야 합니다 . 표 2-8 을 참조하십시오 .
배열 PS6500 설치 설치 및 구성 표 2-7: PS6500 배송상자 내용물 ( 계속 ) 구성 요소 설명 전원 케이블 배송상자에는 배열을 배치할 국가의 전기 요구사항을 충족시 킬 수 있도록 멀티 전원 케이블이 함께 제공될 수 있습니다 . 구성에 적합한 케이블을 사용합니다 . 전원 케이블이 배송상자에 포함되어 있지 않은 경우 , PS 시리 즈 지원 서비스 제공업체나 재판매 사업자에게 문의하십시오 . 직렬 케이블 어레이와 콘솔 또는 터미널 에뮬레이터 간에 직렬 연결을 생성 합니다 . 설치 유틸리티를 실행하거나 배열 또는 그룹에 대한 네트워크 액세스가 없는 경우 케이블을 사용합니다 . 레일 키트 이 키트를 사용하면 랙에 어레이를 설치할 수 있습니다 . 설치 정보는 랙 장착 지침을 참조하십시오 . 케이블 관리 시스템 이 키트를 사용하면 전원 및 네트워크 케이블을 구성할 수 있 키트 . 습니다 . 설치 정보는 랙 장착 지침을 참조하십시오 .
설치 및 구성 배열 PS6500 설치 랙 장착 요구사항 배열을 표준 , 19 인치 랙에 장착해야 합니다 . 랙 장착 지침은 배송상자에 포 함되어 있습니다 . 이러한 설명서에는 랙 요구 사항 및 랙에 배열 장착 , 디스 크 드라이브 및 다른 구성요소 설치 , 케이블 관리 시스템 설치를 위한 단계 가 포함되어 있습니다 . 하드웨어 설치 2-14 페이지의 시작하기 전에 에 설명된 사전 작업을 완료합니다 . 그 다음 에 , 다음 단계에 따라 PS6500 배열을 설치합니다 . 1. 전원 케이블을 연결하십시오 . 이때 배열의 전원을 켜지 마십시오 . 2-17 페이지의 1 단계 : 전원에 배열 연결 을 참조하십시오 . 2. 배열을 네트워크에 연결하십시오 . 2-21 페이지의 2 단계 : 네트워크에 배열 연결 을 참조하십시오 . 3. 배열의 전원을 켜십시오 . 2-23 페이지의 3 단계 : 배열 전원 켜기 를 참조 하십시오 . 4.
배열 PS6500 설치 설치 및 구성 배열과 함께 제공되는 전원 케이블을 준비합니다 . 배열이 전원 케이블과 함 께 제공되지 않은 경우 , PS 시리즈 지원 제공업체 또는 재판매 사업자에 문 의하여 전원 케이블 정보를 확인하십시오 . 주 : Dell 에서는 제공된 약 2m 길이의 C113/C14 전원 케이블을 배열에 연결 할 것을 권장합니다 . 이러한 케이블은 케이블 관리 시스템을 통해 배선 하기에 알맞은 길이로 , 전원 공급 장치 모듈에 팽팽하게 연결하도록 고 안되었습니다 . 필요한 경우 , 약 3.3m 길이의 C13/C14 연장 케이블 또 는 국가 지정 케이블을 전원 공급 장치 케이블 끝에 연결합니다 . 전원 공급 장치 및 냉각 모듈을 모두 전원에 연결합니다 . 케이블 고정 완화 장치를 사용하여 각각 전원 케이블을 배열에 고정시킵니다 . 가용성 증대를 위해 다음의 전원 권장사항을 준수하십시오 : • 개별 회로에 있는 다른 전원 공급원에 전원 공급 장치 및 냉각 모듈을 연 결합니다 .
설치 및 구성 배열 PS6500 설치 전원 ( 및 네트워크 ) 케이블을 구성하려면 케이블 관리 시스템을 사용해야 합니다 . 케이블 관리 시스템을 사용하면 케이블을 제거하지 않고 섀시 커버 를 열 수 있습니다 . 케이블 관리 시스템은 그림 2-12 와 같이 2 개의 배선 조립품으로 구성되어 있 습니다 . • 한 부품에는 지지대 3 개 , 클램프 3 개 , 찍찍이 (fabric hook-and-loop fastener) 6 개가 있습니다 . • 다른 부품에는 지지대 1 개 , 클램프 2 개 , 찍찍이 3 개가 있습니다 . 그림 2-12: 케이블 관리 시스템 - 설치되어 있지 않음 케이블 관리 시스템은 배열 섀시의 후면과 랙 레일에 장착됩니다 . 그림 2-13 을 참조하십시오 .
배열 PS6500 설치 설치 및 구성 케이블 관리 시스템 설치에 대한 정보는 랙 장착 지침 을 참조하십시오 . 케이블 관리 시스템을 사용하려면 : 1. 그림 2-14 에 보여진 대로 전원 케이블을 모아서 3 개의 지지대 중 상단 지지대를 따라 에서 로 케이블을 배선합니다 . 배열 후면 패널과 케 이블 관리 시스템에 대한 첫번째 연결 사이에 케이블이 여유 있게 놓이 도록 합니다 ( ). 그림 2-14: 케이블 배선도 2. 지지대에 있는 3 개의 찍찍이를 연결하고 지지대 아래에 케이블이 위치 하는지 확인합니다 . 그림 2-15 를 참조하십시오 . 그림 2-15: 찍찍이 부착 3. 그림 2-14 에 보여진 대로 3 개의 지지대 중에서 중간 지지대를 따라 에서 로 케이블을 배선합니다 .
배열 PS6500 설치 설치 및 구성 4. 그림 2-14 에 보여진 대로 ( 왼쪽 및 오른쪽 레일의 상단에 연결된 ) 1 개 의 지지대를 따라 에서 으로 케이블을 배선합니다 . 케이블 배선 후 , 설치 결과는 그림 2-16 에 보여진 것과 유사해야 합니다 . 그림 2-16: 케이블 관리 시스템에 장착된 케이블 주 : 배열의 전원을 켜지 마십시오 . 이때 , 전원 케이블은 접지 목적으로만 사용됩니다 . 전원 공급 장치를 전원 공급원에 연결하면 , 배열이 대기 모드에 들어갑니다 . 대기 모드에서 , 배열은 완전히 접지되며 일부 배열 구성부품에는 전원 이 공급됩니다 . 예를 들어 , 전원 단추가 점등되고 LCD 패널이 "standby ( 대기 )" 를 표시합니다 . 그러나 , 디스크와 제어 모듈에는 전원이 공급 되지 않으므로 배열은 작동되지 않습니다 . 2 단계 : 네트워크에 배열 연결 PS6500 배열에는 2 개의 제어 모듈이 포함되어 있습니다 .
배열 PS6500 설치 설치 및 구성 최소한 2 개의 제어 모듈에 있는 이더넷 0 에 네트워크 케이블을 연결한 후 케이블을 네트워크 스위치에 연결해야 합니다 . 그림 2-17 을 참조하십시오 . 그림 2-17: 최소 네트워크 구성 - PS6500 최대 수준의 대역폭 및 가용성을 위해 , 모든 네트워크 인터페이스를 다중 네트워크 스위치에 연결할 때에는 8 개의 네트워크 케이블을 사용하는 것이 좋습니다 . 스위치는 대역폭이 충분한 상호스위치 링크와 함께 연결해야 합 니다 . 그림 2-18 을 참조하십시오 .
배열 PS6500 설치 설치 및 구성 그림 2-18: 권장 네트워크 구성 - PS6500 케이블 관리 시스템을 사용하여 전원 케이블과 함께 네트워크 케이블을 구 성하십시오 . 그림 2-12 부터 그림 2-16 까지 참조하십시오 . 3 단계 : 배열 전원 켜기 전원을 켜기 전에 , PS6500 이 주변 온도에 적응하도록 충분한 시간을 둡니 다 ( 예 : 하룻밤 ). 전원 전환을 켜서 배열을 대기 모드에서 정상 작동 모드로 전환시킵니다 . 전원 스위치는 배열 전면에 있습니다 . 배열 전원을 켜려면 다음과 같이 전 면 베젤을 분리해야 합니다 . 1. 베젤 키를 삽입하고 시계 방향으로 돌려 베젤을 잠금 해제합니다 . 그림 2-19 를 참조하십시오 .
배열 PS6500 설치 설치 및 구성 그림 2-19: 베젤의 잠금 장치 해제 2. 베젤을 오른쪽으로 잡고 베젤 분리 래치를 왼쪽으로 들어올려서 베젤을 섀시에서 분리합니다 . 그림 2-20 을 참조하십시오 . 그림 2-20: 베젤 분리 래치 누르기 3. 베젤을 섀시에서 당겨 빼냅니다 . 그림 2-21 을 참조하십시오 .
설치 및 구성 배열 PS6500 설치 4. 전면 패널에 있는 파란색 전원 단추를 누릅니다 . 주 : 전원이 켜지면 , 전지가 충전되기 시작하고 일부 하드웨어 구성부품이 동기화되기 시작합니다 . 배열 LED 는 이러한 활동 , 즉 정상적인 배열 동작을 나타냅니다 . 베젤을 설치하고 잠그려면 : 1. 랙의 전면을 마주하고 베젤 오른쪽을 섀시 오른쪽에 맞춥니다 . 2. 베젤의 왼쪽이 섀시와 맞물릴 때까지 섀시쪽으로 베젤을 누릅니다 . 3. 베젤 키를 삽입하고 시계 반대 방향으로 돌린 다음 섀시에 베젤을 잠금 니다 . 4 단계 : 배열 직렬 연결 설정 소프트웨어를 구성하기 위해 설치 유틸리티를 사용할 계획이라면 , 직렬 연 결을 구성해야 합니다 . 원격 설치 마법사를 사용할 계획이라면 , 직렬 연결 이 필요하지 않습니다 . 원격 설치 마법사 요구사항에 대한 정보는 3-1 페이 지의 1 단계 : 구성 방법 선택 을 참조하십시오 .
배열 PS6500 설치 설치 및 구성 그림 2-22: 배열에 직렬 케이블 연결 직렬 연결은 다음과 같은 특성을 가지고 있어야 합니다 : • 9600 보드 • 1 개의 STOP 비트 • 패리티 없음 • 데이터 비트 : 8 • 흐름제어 없음 주 : 직렬 케이블을 보관하십시오 . 네트워크 액세스가 없는 경우 , 직렬 케 이블을 사용하여 그룹 또는 개별 어레이를 관리해야 합니다 . 하드웨어 설치를 완료하였으면 3 장 , 소프트웨어 구성을 참조하십시오 .
3 소프트웨어 구성 배열 하드웨어 설치를 완료하였으면 , 배열을 초기화하고 첫번째 그룹 멤버 로서 배열을 포함하는 PS 시리즈 그룹을 생성할 수 있습니다 . 또는 , 기존의 그룹에 배열을 추가할 수 있습니다 . 그룹을 확장한 경우 , 사용자에게 아무 런 영향을 주지 않으면서 용량과 성능이 자동으로 증가됩니다 . • 3-1 페이지의 1 단계 : 구성 방법 선택 . • 3-2 페이지의 2 단계 : 구성 정보 수집 . • 3-4 페이지의 3 단계 : 소프트웨어 구성 시작 . • 3-8 페이지의 4 단계 : 멤버 RAID 정책 설정 . 소프트웨어 구성을 완료하였으면 , 스토리지를 할당하고 SAN 의 사용을 시 작할 수 있습니다 . 4 장 , 스토리지 할당을 참조하십시오 . 1 단계 : 구성 방법 선택 다음과 같은 2 가지 방법으로 소프트웨어를 구성할 수 있습니다 . 다음 중 한 가지 방법을 선택합니다 : • 원격 설치 마법사 사용 . • 설치 유틸리티 사용 .
소프트웨어 구성 설치 및 구성 원격 설치 마법사에는 다음과 같은 요구사항이 있습니다 : • Windows XP 이상의 버전의 OS 가 실행중인 컴퓨터 . • 배열과 컴퓨터의 연결 . 두 가지 옵션이 있습니다 : – 배열과 동일한 이더넷 세그먼트에 컴퓨터를 연결하고 2 계층 (Layer 2) 멀티캐스팅이 배열과 컴퓨터 사이에서 차단되지 않도록 합니다 . – RJ45 네트워크 케이블을 사용하여 배열의 활성 제어 모듈에 있는 이더 넷 0 에 컴퓨터를 연결합니다 (ACT LED 가 녹색입니다 ). 설치 유틸리티 정보 설치 유틸리티는 배열 및 그룹 구성에 대한 정보를 표시해주는 상호작용 명 령 행 유틸리티입니다 . 설치 유틸리티를 사용하려면 , 배열과 콘솔 터미널 또는 터미널 에뮬레이터 를 실행하는 컴퓨터에 직렬 연결합니다 . 방법을 선택 후 , 배열 구성에 필요한 정보를 수집합니다 .
소프트웨어 구성 설치 및 구성 표 3-1: 배열 구성 ( 계속 ) 입력하십시오 설명 Netmask ( 넷마스크 ) 위에 설명한 배열 네트워크 인터페이스가 위치하는 서브넷을 확인 하기 위해 IP 주소와 통합된 주소 ( 기본값은 255.255.255.0 입니다 ). Default gateway (optional) 기본 게이트웨 이 ( 옵션 ) 로컬 네트워크 범위를 넘어 서브넷을 연결하고 네트워크 소통량 을 처리하는데 사용되는 장치를 위한 네트워크 주소 . 배열 네트 워크 인터페이스로 로컬 네트워크 외부에서 통신을 하고자 하는 경우 ( 예를 들어 , 로컬 네트워크 외부의 컴퓨터에서 볼륨에 액세 스할 수 있도록 하는 경우 ) 에만 기본 게이트웨이가 필요합니다 . 주: RAID policy (RAID 정책 ) 기본 게이트웨이는 배열 네트워크 인터페이스와 동일한 서 브넷에 위치해야 합니다 . 배열용 RAID 레벨 및 예비 디스크 드라이브 구성 .
소프트웨어 구성 설치 및 구성 표 3-2: 그룹 구성 입력하십시오 Password for the 설명 grpadmin 계정에 대한 초기 설정 그룹 관리 암호 (grpadmin) 를 무효화시키는 암호 . 암호는 3-16 개의 문자 또는 숫자로 구성되 어야 하며 대소문자를 구분합니다 . (grpadmin 계정 새로운 그룹을 생성할 경우에만 필요합니다 . 에 대한 암호 ) grpadmin account Microsoft service 그룹에 대한 Microsoft 서비스 (VSS 또는 VDS) 액세스를 활성화 user name and 하기 위해 사용되는 CHAP 사용자 이름과 암호 . 사용자 이름은 password 3-63 개의 영문자로 구성되어야 합니다 . 암호는 12-16 개의 영숫 (optional) 자로 구성되어야 하며 대소문자를 구분합니다 .
설치 및 구성 소프트웨어 구성 4. 입력 화면이 나타나면 , 표 3-1 및 표 3-2 에서 배열 및 그룹 구성 정보를 입력합니다 . 기본값을 적용하려면 키를 누릅니다 . 도움말을 확인 하려면 물음표 (?) 를 입력합니다 . 첫번째 멤버로서 배열을 포함하는 그룹을 생성할 것인지 또는 기존 그룹 에 배열을 추가할 것인지 여부를 지정합니다 . 주 : 배열이 네트워크를 검색하는 과정으로 인해 그룹 IP 주소를 입력한 후 약간의 지연이 발생될 수 있습니다 . 배열을 초기화하고 그룹을 생성하기 위해 설치 유틸리티를 사용하는 방법에 대한 예가 예 3-1 에 제시되어 있습니다 . 설치가 완료되면 디스크 스토리지를 사용하기 위해서는 멤버의 RAID 정책을 설정해야 합니다 . 3-8 페이지의 4 단계 : 멤버 RAID 정책 설정 으로 가십시오 .
소프트웨어 구성 설치 및 구성 예 3-1: 시스템 설치 유틸리티 사용 Login: grpadmin Password: xxxxxxxx Welcome to Group Manager Copyright 2001 - 2008 Dell, Inc. It appears that the storage array has not been configured. Would you like to configure the array now? (y/n) [n] y Group Manager Setup Utility The setup utility establishes the initial network and storage configuration for a storage array and then configures the array as a member or a new or existing group of arrays. For help, enter a question mark (?) at a prompt.
설치 및 구성 소프트웨어 구성 소프트웨어 구성을 위해 원격 설치 마법사 사용하기 원격 설치 마법사는 호스트 통합 툴 CD-ROM 에 있으며 Windows 컴퓨터에 설치해야 합니다 . 호스트 통합 툴 사용 설명서는 원격 설치 마법사의 전체 기능의 사용에 대한 상세 정보를 제공합니다 . 원격 설치 마법사를 실행하려면 다음 절차를 따릅니다 : 1. 3-1 페이지의 1 단계 : 구성 방법 선택 의 요구사항에 부합하는 컴퓨터를 선택합니다 . 2. 배송상자에서 호스트 통합 툴 CD-ROM 을 꺼내서 준비합니다 . 3. CD-ROM 을 컴퓨터에 넣고 원격 설치 마법사를 설치합니다 . 4. 다음과 같이 클릭하여 원격 설치 마법사를 시작합니다 : Start ( 시작 )> Programs ( 프로그램 ) > EqualLogic > Remote Setup Wizard ( 원격 설치 마법사 ) 5. 환영합니다 대화상자에서 , PS 시리즈 배열 초기화를 선택하고 다음을 클릭합니다 .
설치 및 구성 소프트웨어 구성 새로운 그룹을 생성한 경우 , 4 장 , 스토리지 할당으로 이동합니다 . 4 단계 : 멤버 RAID 정책 설정 새 그룹 멤버 ( 배열 ) 에서 스토리지 공간은 멤버에 RAID 정책을 구성한 후 에 사용할 수 있습니다 . RAID 정책은 RAID 수준과 예비 디스크 구성으로 구성됩니다 . RAID 정책을 선택할 경우 , 멤버 디스크는 선택된 RAID 레벨 및 예비 디스크의 해당 번호로 자동 구성됩니다 . 원격 설치 마법사를 사용하여 그룹을 생성하려면 , 첫번째 멤버에 대한 RAID 정책은 소프트웨어 구성시 선택한 RAID 정책에 따라 설정되며 스토 리지를 사용할 수 있습니다 . 4 장 , 스토리지 할당을 참조하십시오 . 설치 유틸리티를 사용하여 그룹을 생성하거나 확장하는 경우 또는 원격 설 치 마법사를 사용하여 배열을 기존 그룹에 추가하는 경우 , 그룹 멤버용 RAID 정책을 설정해야 합니다 .
소프트웨어 구성 설치 및 구성 2. 그룹 관리자 명령 화면에서 다음 명령을 입력합니다 : member select member_name raid-policy policy policy ( 정책 ) 변수에 대한 raid50, raid5, raid10, 또는 raid6 을 지정합니다 . 예를 들어 , 다음 명령은 RAID50 가 설정된 member1 을 구성합니다 : group1> member select member1 raid-policy raid50 GUI 를 사용하여 RAID 정책 설정 그룹 관리자 GUI 에 대한 브라우저 지원과 관련된 최신 정보는 PS 시리즈 발 행 정보를 참조하십시오 . 멤버에 대한 RAID 정책을 설정하기 위해 GUI 를 사용하려면 : 1. 웹 브라우저에서 그룹 IP 주소를 입력하여 그룹에 로그인합니다 . 그 다 음 , 로그인 대화상자 ( 그림 3-1) 에서 , 그룹을 생성할 때 지정한 grpadmin 계정 이름과 암호를 입력합니다 . 그림 3-1: GUI 로그인 2.
설치 및 구성 소프트웨어 구성 그림 3-2: 그룹 요약 - RAID 정책이 멤버에 설정되지 않습니다 3. 표시되는 경고 메시지 대화상자에서 , 예를 클릭하여 멤버에 RAID 를 구 성합니다 . 4. 멤버 구성 – 일반 설정 대화상자 ( 그림 3-3) 에서 , 다음을 클릭합니다 .
소프트웨어 구성 설치 및 구성 그림 3-3: 멤버 구성 - 일반 설정 5. 멤버 구성 - RAID 구성 대화상자 ( 그림 3-4) 에서 , 다음을 수행한 후 다음 을 클릭합니다 . • RAID 정책을 선택합니다 . • 선택적으로 , RAID 확인이 완료되고 전지가 완전히 충전될 때까지 멤버의 스토리지 공간 사용을 지연시키려면 , 멤버 스토리지 초기화 가 완료될 때까지 대기 (Wait) 를 선택합니다 . 기본값으로 RAID 확 인이 완료될 때까지 성능이 최적화되지 않더라도 스토리지 공간은 즉시 사용이 가능합니다 .
소프트웨어 구성 설치 및 구성 6. 멤버 구성이 만족스러운 경우 , 멤버 구성 - 요약 대화상자 ( 그림 3-5) 에 서 종료를 클릭합니다 . 변경하려면 뒤로를 클릭합니다 . 그림 3-5: 멤버 구성 - 요약 배열 스토리지를 사용할 준비가 되어 있습니다 .
4 스토리지 할당 그룹 스토리지 공간을 사용자에게 할당하는 과정에는 다음 단계가 포함됩 니다 . • 4-1 페이지의 1 단계 : 볼륨 생성 • 4-5 페이지의 2 단계 : 볼륨에 컴퓨터 연결 스토리지를 할당하면 , 그룹을 사용자 정의하고 보다 고급한 기능을 사용할 수 있습니다 . 장 5, 추가 정보를 참조하십시오 . 1 단계 : 볼륨 생성 그룹 스토리지 공간을 사용자와 응용 프로그램에 할당하려면 , 그룹 관리자 CLI 또는 GUI 를 사용하여 볼륨을 생성합니다 . 볼륨이 네트워크에서 iSCSI 대 상으로 표시됩니다 . 볼륨을 생성할 경우 , 표 4-1 에 설명된 정보를 지정합니다 . 표 4-1: 볼륨 구성 구성 요소 설명 볼륨 이름 볼륨 이름은 고유한 이름으로 63 개 이하의 문자 ( 문자 , 숫자 , 마침 표 , 하이픈 , 콜론 포함 ) 로 구성이 가능합니다 . 볼륨 이름은 볼륨에 대해 자동으로 생성되는 iSCSI 대상 이름의 끝에 첨부됩니다 .
설치 및 구성 스토리지 할당 선택적으로 볼륨 스냅샷용 공간을 할당하거나 씬 프로비져닝으로 볼륨을 구성할 수 있습니다 . 그러나 , 씬 프로비져닝이 모든 스토리지 환경에 적절 한 것은 아닙니다 . 고급 볼륨 기능에 대한 정보는 PS 시리즈 그룹 관리 설명 서를 참조하십시오 . 볼륨 생성을 위해 CLI 사용하기 1. 시스템에 로그인합니다 . 이러한 방법 중 1 개를 사용하여 그룹에 연결합니다 : • 멤버에 대한 직렬 연결 . 2-11 페이지의 4 단계 : 배열에 직렬 연결 설정 또는 2-25 페이지의 4 단계 : 배열 직렬 연결 설정 을 참조하십시오 . • 그룹 IP 주소에 대한 텔넷 또는 ssh 연결 . 로그인하라는 메시지가 화면에 나타나면 , 그룹을 생성할 때 지정한 grpadmin 계정 이름과 암호를 입력합니다 . 2.
스토리지 할당 설치 및 구성 볼륨 생성을 위해 GUI 사용하기 1. 시스템에 로그인합니다 . 웹 브라우저에서 그룹 IP 주소를 지정합니다 . 그 다음 , 로그인 대화상자 ( 그림 3-1) 에서 , 그룹을 생성할 때 지정한 grpadmin 계정 이름과 암호 를 입력합니다 . 2. 그룹 요약 창에서 , 작동 (Activities) 패널의 볼륨 생성을 클릭합니다 . 3. 볼륨 이름 및 선택 사양인 설명 ( 그림 4-1) 을 입력하고 다음을 클릭합니다 . 그림 4-1: 볼륨 생성 - 볼륨 설정 4. 볼륨 크기를 입력하고 다음 ( 그림 4-2) 을 클릭합니다 . 표의 값은 사용자 가 지정한 크기를 반영합니다 .
스토리지 할당 설치 및 구성 그림 4-2: 볼륨 생성 - 공간 준비 5. 액세스 제어 기록에 대한 iSCSI 초기자 이름 또는 IP 주소를 지정하고 다 음 ( 그림 4-3) 을 클릭합니다 . 그림 4-3: 볼륨 생성 - iSCSI 액세스 6. 요약 정보를 살펴 보고 ( 그림 4-4) 볼륨 구성이 올바르면 마침을 클릭합 니다 . 변경하려면 뒤로를 클릭합니다 .
스토리지 할당 설치 및 구성 그림 4-4: 볼륨 생성 - 요약 2 단계 : 볼륨에 컴퓨터 연결 볼륨을 생성하면 PS 시리즈 그룹은 자동으로 iSCSI 대상 이름을 생성하며 대상 이름 하단에 볼륨 이름이 표시됩니다 . 각 볼륨이 네트워크에서 iSCSI 대상으로 표시됩니다 . 이름이 dbvol 인 볼륨에 대한 iSCSI 대상 이름의 예는 다음과 같습니다 : iqn.2001-05.com.equallogic.5-4a0900-2f00000-007eca92d654f160-dbvol 컴퓨터를 볼륨에 연결하려면 : 1. 컴퓨터에 iSCSI 초기자를 설치하고 구성합니다 . 하드웨어 및 소프트웨 어 초기자는 다양한 벤더의 제품을 사용할 수 있습니다 . 벤더가 제공한 지침을 사용하여 초기자를 구성합니다 . 주 : Dell 은 기술 지원 웹 사이트를 방문하여 초기자를 이용하여 그룹 볼 륨에 PS 시리즈를 액세스하는 방법에 대한 중요한 정보를 얻을 것 을 권장합니다 .
설치 및 구성 스토리지 할당 2. 컴퓨터가 볼륨의 액세스 제어 기록 중 하나에 부합되는지 확인합니다 . 볼륨에 대한 기록을 표시하려면 : • CLI 를 사용하여 다음의 명령을 입력합니다 : volume select volume_name access show • GUI 를 사용하여 가장 왼쪽에 있는 패널에서 볼륨을 확장하고 , 볼륨 이름을 선택한 후 , 액세스 탭을 클릭합니다 . 필요한 경우 , CLI 또는 GUI 를 사용하여 컴퓨터가 대조할 액세스 제어 기록을 생성합니다 . 3. 볼륨에 대한 iSCSI 대상 이름을 표시하려면 : • CLI 를 사용하여 다음의 명령을 입력합니다 : volume select volume_name access show • GUI 를 사용하여 가장 왼쪽에 있는 패널에서 볼륨을 확장하고 , 볼륨 이름을 선택한 후 , 연결 탭을 클릭합니다 . 4. 컴퓨터에서 iSCSI 초기자 유틸리티를 사용하여 그룹 IP 주소를 iSCSI 검 색 주소로 지정합니다 .
5 추가 정보 SAN 의 사용을 시작한 후 그룹을 사용자 정의하여 스토리지 환경을 보다 효 율적으로 관리할 수 있습니다 . 또한 , 제품의 모든 기능 사용을 시작할 수 있 습니다 . PS 시리즈 그룹 관리 설명서에는 스토리지 개념과 그룹 관리자 GUI 를 사용 하여 그룹을 관리하는 방법에 대한 상세한 정보가 포함되어 있습니다 . PS 시리즈 CLI 참조 설명서는 그룹 및 개멸 배열 관리를 위해 그룹 관리자 GUI 를 사용하는 방법을 설명합니다 . 일반적인 그룹 사용자 정의 작업 표 5-1 일반적인 그룹 사용자 정의 작업을 설명합니다 . 이러한 작업들은 PS 시리즈 그룹 관리 설명서에 자세히 설명되어 있습니다 . 표 5-1: 일반적인 그룹 사용자 정의 작업 작업 설명 그룹 멤버에 네트워크 연결 추가 다중 네트워크 연결은 성능과 가용성을 향상시키며 다중 경로 I/O 에 필요합니다 .
설치 및 구성 추가 정보 고급 그룹 관리 작업 표 5-2 고급 그룹 관리 작업을 설명합니다 . 이러한 작업들은 PS 시리즈 그룹 관리 설명서에 자세히 설명되어 있습니다 . 표 5-2: 고급 관리 작업 작업 설명 그룹에 멤버 추가 1 명의 멤버로 구성된 그룹이 완전한 기능을 수행하더라 도 , 보다 많은 수의 배열을 추가하면 데이터 가용성에 대 한 방해 없이 용량이 확장되고 , 네트워크 대역폭이 증가 되며 , 전체적인 그룹 성능이 향상됩니다 . 풀 생성 다수의 멤버로 구성된 그룹을 사용하여 다수의 풀을 생 성하고 계층형 스토리지 솔루션을 위해 멤버와 볼륨을 풀에 지정할 수 있습니다 . 전용 관리 네트워크 설정 보안 목적을 위해 개별 관리 네트워크를 필요로 할 수 있 습니다 . 볼륨 스냅샷 생성 스냅샷은 백업에 사용이 가능한 볼륨 데이터의 특정 시 점 (PiT) 복사본입니다 .
색인 A array network address 3-2 C CHAP 계정 , 구성 5-1 CLI RAID 정책 설정 3-8 볼륨 생성 4-2 G GUI RAID 정책 설정 3-8, 3-9 볼륨 생성 4-3 I iSNS, 구성 5-1 N NTP 서버 , 구성 5-1 P PS 시리즈 배열 네트워크 권장 사항 2-2 네트워크 요구 사항 2-2 다중경로 I/O 권장 사항 2-2 대역폭 증가 2-2 방전으로부터 보호 2-1 서브넷 액세스 권장 사항 2-2 PS6000 기술 사양 2-5 네트워크 구성 2-9 네트워크 요구 사항 2-9 네트워크 케이블 2-9 네트워크 케이블 연결 2-9 랙 장착 요구 사항 2-7 배송상자 내용물 2-6 설치 2-4 전원 권장 사항 2-5 전원 케이블 연결 2-8 전원 켜기 2-11 제어 모듈 2-6 직렬 케이블 연결 2-11 하드웨어 설치 2-7 하드웨어 요구 사항 2-6 환경 권장 사항 2-5 PS6500 기술 사양 2-14 네트워크 구성 2-22 네트워크 요구 사항 2
설치 및 구성 R RAID 레벨 , 지원 3-8 RAID 정책 CLI 와 함께 설정 3-8 GUI 와 함께 설정 3-9 설명 3-8 S SNMP, 구성 5-1 V VLAN 권장사항 2-3 Z 계정 , 설치후 구성 5-1 권장 전원 구성 2-19 그룹 CLI 에 로그인 3-8 GUI 에 로그인 3-9 IP 주소 3-3 고급 작업 5-1 생성 3-1, 3-2 설치후 사용자 정의 5-1 컴퓨터에서 볼륨에 액세스 4-6 확장 3-1, 3-2 그룹명 3-3 기가비트 이더넷 권장사항 2-2 기술 사양 PS6000 2-5 PS6500 2-14 날짜 , 설정 5-1 네트워크 권장사항 2-2 그룹 IP 주소 3-3 다중 네트워크 구성 5-1 배열 IP 주소 3-2 성능 개선 2-2 요구사항 2-2 색인 –2 색인 네트워크 구성 PS6000 2-9 PS6500 2-22 네트워크 인터페이스 구성 3-2 네트워크 케이블 연결 , PS6000 2-9 연결 , PS6500 2-21 네트워크 케이블 연결 PS6000
설치 및 구성 베젤 분리 PS6500 2-23 베젤 설치 PS6500 2-25 볼륨 4-1 CLI 로 생성 4-2 GUI 로 생성 4-3 네이밍 4-1 대상 이름 4-6 보고된 크기 4-1 생성 4-1 스냅샷 공간 4-2 씬 프로비져닝 설정 4-2 액세스 제어 4-1 컴퓨터에서 액세스 4-6 설치 유틸리티 설명 3-2 소프트웨어 구성 3-4 요구사항 3-2 소프트웨어 구성 , 방법 3-2 스냅샷 , 여유 공간 4-2 스위치 VLAN 권장사항 2-3 대역폭 요구사항 2-10 링크 권장사항 2-10 스패닝 트리 권장사항 2-3 유니캐스트 폭주 제어 권장사항 2-3 점보 프레임 권장사항 2-3 흐름 제어 권장사항 2-3 스패닝 트리 권장사항 2-3 시간 , 설정 5-1 씬 프로비져닝 , 볼륨에서 활성화 4-2 액세스 제어 CLI 로 구성 4-2 GUI 로 구성 4-4 볼륨 보호 4-1 색인 완전 전원 모드 , 지정 2-23 원격 설치 마법사 설명 3-1 소프트웨어 구성 3-7 요구사항 3-1 유니
설치 및 구성 색인 케이블 ( 직렬 ) 필수 특징 2-26 케이블 관리 시스템 2-17 하드웨어 설치 PS6000 2-4, 2-7 PS6500 2-13, 2-17 호스트 점보 프레임 권장사항 2-3 흐름 제어 권장사항 2-3 호스트 통합 툴 , 설명 3-7 환경 권장 사항 PS6000 2-5 하드웨어 요구 사항 PS6000 2-6 PS6500 2-15 환경 요구 사항 PS6500 2-14 색인 –4 흐름 제어 권장사항 2-3