Install Guide
PS6210 インストールとセットアップガイド
4 ソフトウェア設定
IP address for network interface []: 192.17.2.41
Netmask [255.255.255.0]:
Default gateway [192.17.2.1]:
Enter the name and IP address of the group that the array will join.
Group name []: group1
Group IP address []: 192.17.2.20
Searching to see if the group exists.This may take a few minutes.
The group does not exist or currently cannot be reached.Make sure you have entered the correct
group IP address and group name.
Do you want to create a new group (yes | no) [yes]?yes
Group Configuration
Group Name: group1
Group IP address: 192.17.2.20
Do you want to use the group settings shown above (yes | no) [yes]: yes
Password for managing group membership:
Retype password for verification:
Password for the default group administration account:
Retype password for verification:
Saving the configuration ...
Waiting for configuration to become active......Done
Group member member1 now active in the group.
Group group1 has been created with one member.
Use the Group Manager GUI or CLI to set the RAID policy for the member.You can then create a
volume that a host can connect to using an iSCSI initiator.
group1>
リモート セット アップウィザードを使 用 したソフト ウェアの設 定
リモートセットアップウィザードは『HostIntegrationTools』CD-ROMに収録されており、WindowsまたはLinuxコ
ンピュータにインストールする必要があります。『HostIntegrationToolsUserGuide』( HostIntegrationTools
ユーザーガイド) には、リモートセットアップウィザード の全機能の使用に関する詳細情報が記載されています。
リモートセットアップウィザードを実行するには、次の手順に従います。
1. 17ページの「設定方法の選択」の要件を満たすコンピュータを使用します。
2. 配送ボックスから『HostIntegrationTools』CD-ROMを取り出す、またはサポートサイトから『HostIntegration
Tools』キットをダウンロードします。
3. 『HostIntegrationTools』マニュアルの手順に従って、リモートセットアップウィザード をインストールします。
4. スタート、プログラム、EqualLogic、Remote Setup Wizard(リモートセットアップウィザード )とクリックして、リモートセット
アップウィザード を起動します。
5. Welcome( ようこそ) ダイアログボックスで、Initialize a PS Series array( PSSeriesアレイを初期化する)
を選択し、Next( 次へ) をクリックします。
メモ: アレイと通 信 できない場 合は、ネットワーク設 定を確 認してください。setupユーティリティを使 用したソフトウ
ェアの設 定 が必要 になる場合 もあります。
6. 初期化するアレイを選択し、Next( 次へ) をクリックします。
7. InitializeArray( アレイの初期化) ダイアログボックスで、表6のアレイ設定を入力し、グループを作成するか
既存のグループに追加するかを選択します。Next( 次へ) をクリックします
8. CreateaNewGroup( 新規グループの作成) ダイアログボックスまたはJoinanExistingGroup( 既存のグルー
プへの追加) ダイアログボックスで、表7からグループ設定を入力し、Next( 次へ) をクリックします。
9. Finish( 完了) をクリックしてウィザードを終了します。
20