Users Guide
Table Of Contents
- Dell EqualLogic Host Integration Tools for Microsoft Edition Version 5.4 Installation and User's Guide
- About This Guide
- Introduction to Host Integration Tools
- Installation
- Obtain the Installation Kit
- Installation Considerations
- Install Host Integration Tools for Microsoft
- Install HIT/Microsoft on a Windows Server Core Machine
- Install HIT on a Windows Server Core Cluster
- About Remote Host Installations
- Install HIT on a Failover Cluster
- About Silent Installations
- Using HIT With a SharePoint Farm
- Remote Setup Wizard
- Remote Setup Command Line Utility
- Using the Multipath I/O Component
- Use the VDS Provider
- Use SCVMM With the Dell EqualLogic SMP
- Install the Dell EqualLogic Storage Management Provider
- Configure the Dell EqualLogic Storage Management Provider
- Create a Classification for Dell EqualLogic Storage Resources
- Import the SMP Through the SCVMM GUI
- Configure PS Series Groups
- Configure Group Access on Managed Hosts and Clusters
- Configure Storage for VM Rapid Provisioning
- Create a VM Template From a VHD
- Migrate the Rapid-Provisioned VMs
- Migrate Storage of a Deployed VM to Another Location
- Troubleshoot SCVMM Issues
- Supported SMP PowerShell Cmdlets
- Use the HPC iSCSI Provider
- Tools and Utilities
- Index
Table 7. Initialize Array Command Options (continued)
Parameter Argument Description
You must specify either the ‑CreateGroup or the
‑JoinGroup parameter. With the ‑CreateGroup
parameter, you must also enter the ‑GroupName and
‑GroupIP command parameters.
SerialNumber= serial number Designates the serial number of the PS Series array to be
initialized. Use either this option or the ServiceTag
option, but not both.
ServiceTag= service tag number Designates the service tag number of the PS Series array
to be initialized. Use either this option or the
SerialNumber option, but not both.
MemberName= member name (Required) Designates the member name of the PS Series
array to be initialized.
MemberIPEth0= IP address (Required) Designates the IP address for the Ethernet 0
network interface that controls access to the PS Series
array to be initialized.
MemberSubnet= subnet mask (Required) Designates the IP address for the subnet
controlling access to the PS Series array to be initialized.
MemberGateway= IP address (Required) Designates the IP address of the gateway to
use for access to the PS Series array to be initialized.
CreateGroup Specifies that a new group should be created using the
specified group name and group IP address. Make sure the
name and IP address you enter are not used by any other
group.
GroupName= group name (Required with CreateGroup) Designates the name of a
specific PS Series group for which configuration
information is requested.
JoinGroup Specifies that the member array should join the group with
the specified group name and group IP address.
GroupIP= IP address Designates the IP address to be used for accessing the
group.
Admin= group admin password (Required with CreateGroup) Specifies the password to be
used for default group administration user access to the
specified group.
Membership= password Specifies the password to be used for authenticating
membership access to the specified group.
RAID= 10|50|6|6‑accelerated (Required with CreateGroup) Specifies the RAID policy for
the member.
ChapUser= CHAP user name (Required with CreateGroup) Specifies the CHAP user
name to be used for authenticating access to arrays in the
specified group.
ChapSecret= CHAP password (Required with CreateGroup) Specifies the password to be
used for authenticating access to arrays in the specified
group.
DCBVlanID= data center bridging VLAN ID Designates the VLAN ID if you are using data center
bridging (DCB).
NOTE: For a complete listing of RAID policies on PS Series systems, see the Dell Technical Report PS Series Storage
Arrays: Choosing a Member RAID Policy, available from the following location:
en.community.dell.com/techcenter/storage/w/wiki/equallogic-tech-reports.aspx
32 Remote Setup Command Line Utility