Install Guide
5 软 件配置
完成阵列硬件安装后,即可初始化阵列并将此阵列作为第一个组成员创建 PS Series 组。或者,
可向现有组中添加此阵列。扩展组后,其容量和性能会自动提高,而不会对用户造成影响。
完成软件配置后,即可分配存储,开始使用 iSCSI SAN 阵列。请参阅
第
29
页上 存储分配
。
选 择 配置方法
配置软件的方法有两种。选择
一种
方法:
• 使用用于 Windows 或 Linux 的“远程设置向导”。有关使用“远程设置向导”的说明,请参阅
Dell EqualLogic Host Integration Tools for Microsoft Installation and User's Guide(Dell EqualLogic Host
Integration Tools for Microsoft 安装和用户指南)或 Dell EqualLogic Host Integration Tool for Linux
Installation and User's Guide(Dell EqualLogic Host Integration Tools for Linux 安装和用户指南),这些
指南可以在支持站点 eqlsupport.dell.com 上找到。
• 使用 setup 公用程序。setup 公用程序是一种交互命令行公用程序,可提示有关阵列和组配置
的信息。
要使用 setup 公用程序,则必须在阵列与控制台终端或运行终端仿真程序的计算机之间拥有
串行连接。
选择一种方法后,收集阵列配置所需的信息。
收集配置信息
无论您使用哪种方法配置软件,都必须收集表 8 和表 9 中的信息。如有必要,可向网络管理员索取
IP 地址。
此外,确保遵守
第
15
页上 网络要求和建议
中的网络建议。
表 8:阵列配置信息
提 示 说 明
成 员 名 称
组 中 阵 列 的 唯 一 名 称 (最 多 包 含 63 个 字 母 、数 字 或 连 字 符 )。第 一 个 字 符 必 须 是 字
母 或 数 字 。
网 络 接 口 阵 列 上 的 网 络 接 口 名 (例 如 :eth0),该 阵 列 连 接 到 网 络 交 换 机 上 正 常 工 作 的 端 口 。
IP 地 址
阵 列 网 络 接 口 的 网 络 地 址 。
注:每 个 成 员 都 必 须 至 少 拥 有 一 个 与 组 IP 在 相 同 的 子 网 上 的 网 络 接 口 。至
少 需 要 eth0 IP 地 址 和 组 IP 地 址 。
网 络 掩 码
与 IP 地 址 结 合 使 用 的 地 址 ,用 于 识 别 阵 列 网 络 接 口 所 在 的 子 网 (默认 为
255.255.255.0)。
默 认 网 关 (可 选 )
用 于 连 接 子 网 以 及 将 网 络 通 信 传 输 到 本 地 网 络 以 外 的 设 备 的 网 络 地 址 。尽管
Dell 不 建 议 您 在 iSCSI 网 络 上 使 用 路 由 访 问 ,有 时 由 于 以 下 原 因 可 能 是 必 需 的 :
• 远 程 管 理 访 问 (未 定 义 管 理 网 络 时 )
• 访 问 NTP 服 务 器 (通常 不 与 阵 列 和 启 动 器 位 于 同 一 子 网 上 )
• 访 问 用 于 复 制 的 其 他 阵 列
• 用 于 电 子 邮 件 通 知 的 SMTP 服 务 器 访 问 (如果 没 有 单 独 的 管 理 网 络 )
注:默 认 网 关 必 须 与 阵 列 网 络 接 口 处 于 同 一 子 网 中 。
23