Dell G5 15 5500 서비스 매뉴얼 규정 모델: P89F 규정 유형: P89F003 February 2021 개정 A03
참고, 주의 및 경고 노트: 참고"는 제품을 보다 효율적으로 사용하는 데 도움이 되는 중요 정보를 제공합니다. 주의: 주의사항은 하드웨어의 손상 또는 데이터 유실 위험을 설명하며, 이러한 문제를 방지할 수 있는 방법을 알려줍니다. 경고: 경고는 재산 손실, 신체적 상해 또는 사망 위험이 있음을 알려줍니다. © 2020-2021 Dell Inc. or its subsidiaries. All rights reserved. Dell, EMC 및 기타 상표는 Dell Inc. 또는 그 자회사의 상표입니다. 다른 상표는 해당 소유자의 상표일 수 있습니다.
목차 장 1: 컴퓨터 내부 작업.......................................................................................................................6 컴퓨터 내부 작업을 시작하기 전에...................................................................................................................................6 시작하기 전에 ................................................................................................................................................................ 6 안전 지침...............................................
코인 셀 배터리.................................................................................................................................................................... 36 코인 셀 배터리 제거.....................................................................................................................................................36 코인 셀 배터리 설치.....................................................................................................................................................
BIOS(시스템 설정) 및 시스템 암호 지우기..............................................................................................................73 장 5: 문제 해결...............................................................................................................................74 운영 체제 복구.................................................................................................................................................................... 74 시스템 진단 표시등................................................
1 컴퓨터 내부 작업 컴퓨터 내부 작업을 시작하기 전에 노트: 이 문서의 이미지는 주문한 컴퓨터의 구성에 따라 조금씩 다를 수 있습니다. 시작하기 전에 단계 1. 열려 있는 파일을 모두 저장하고 닫은 다음 사용 중인 응용 프로그램을 모두 종료합니다. 2. 컴퓨터를 종료하십시오. Start(시작) > Power(전원) > Shut down(종료)을 클릭합니다. 노트: 다른 운영 체제를 사용하고 있는 경우 해당 운영 체제의 설명서에서 종료 지침을 참조하십시오. 3. 컴퓨터 및 모든 연결된 장치를 전원 콘센트에서 분리하십시오. 4. 키보드, 마우스, 모니터 등과 같은 연결된 모든 네트워크 기기와 주변 장치를 컴퓨터에서 분리합니다. 5. 해당하는 경우, 모든 미디어 카드 및 광학 디스크를 컴퓨터에서 분리합니다. 안전 지침 컴퓨터의 손상을 방지하고 안전하게 작업하기 위해 다음 안전 지침을 따르십시오.
정전기 방전 - ESD 방지 ESD는 확장 카드, 프로세서, 메모리 DIMM, 시스템 보드와 같이 민감한 전자 구성 요소를 다룰 때 아주 중요한 부분입니다. 너무 짧은 시간으로 충전할 경우 간헐적인 문제 또는 제품 수명 단축 등 원인 불명으로 회로가 손상될 수 있습니다. 업계에서 전력 요구 사항의 완화와 집적도 향상을 요구함에 따라 ESD 보호에 대한 관심이 높아지고 있습니다. 최근 Dell 제품에 사용된 반도체의 집적도 향상으로 인해 정전기로 인한 손상 정도가 이전 Dell 제품에 비해 높아짐에 따라 일부 부품 처리에 승인된 이전 방법이 더 이상 적용되지 않게 되었습니다. 두 가지 대표적인 ESD 손상 유형으로는 치명적인 오류와 간헐적으로 발생하는 오류가 있습니다. ● 치명적인 오류 – 이러한 오류는 ESD 관련 오류의 약 20%를 차지합니다. 장치 기능이 즉각적으로 완전히 손실되는 오류입니다.
● ESD 포장 – 모든 ESD에 민감한 장치는 정전기 방지 포장으로 배송 및 제공되어야 합니다. 금속 정전기 방지 가방을 사용하는 것 이 좋습니다. 그러나 부품이 파손된 경우 항상 새 부품을 받은 것과 동일한 ESD 백 및 포장을 사용하여 해당 부품을 반품해야 합니 다. ESD 백을 접은 후 테이프로 밀봉하고 들어 있던 것과 같은 포장 발포제와 함께 새 부품을 받은 원래 상자 안에 넣어야 합니다. ESD에 민감한 장치의 포장은 ESD 방지 작업대에서만 풀어야 하며, 부품을 절대 ESD 백 위에 놓아서는 안 됩니다. 백 안쪽에만 정 전기 차폐 처리가 되어 있기 때문입니다. 부품은 항상 손에 잡고 있거나, ESD 매트 위에 놓거나, 시스템 또는 정전기 방지 가방 안 에 넣으십시오. ● 민감한 구성 요소 운반 – ESD 민감한 구성 요소(예: 교체 부품 또는 Dell에 반환되는 부품)를 운반할 때는 안전한 운반을 위해 해당 부품을 정전기 방지 가방 안에 넣어야 합니다.
2 구성 요소 제거 및 설치 노트: 이 문서의 이미지는 주문한 컴퓨터의 구성에 따라 조금씩 다를 수 있습니다. 권장 도구 이 문서의 절차를 수행하기 위해 다음 도구가 필요할 수 있습니다. ● Phillips(+) 스크루 드라이버 #1 ● 납작 머리 스크루 드라이버 ● 플라스틱 스크라이브 나사 목록 노트: 구성 요소에서 나사를 제거할 때 나사 유형과 나사 수량을 적어둔 후 나사 보관함에 보관하는 것이 좋습니다. 이렇게 하면 구성 요소를 장착할 때 정확한 나사 개수와 올바른 나사 유형으로 복원할 수 있습니다. 노트: 일부 컴퓨터에는 자기 표면이 있습니다. 구성 요소를 교체할 때 나사를 이러한 표면에 부착된 채로 남겨두지 않아야 합니 다. 노트: 나사 색상은 주문한 구성에 따라 달라질 수 있습니다. 표 1.
표 1. 나사 목록 (계속) 구성 요소 고정 위치 나사 유형 수량 좌측 팬 손목 받침대 및 키보드 어 셈블리 M2x3 2 우측 팬 손목 받침대 및 키보드 어 셈블리 M2x3 2 무선 카드 브래킷 시스템 보드 M2x3 1 터치패드 브래킷 손목 받침대 및 키보드 어 셈블리 M2L2 빅헤드 7 지문 인식기가 장착된 전 원 버튼(선택 사항) 손목 받침대 및 키보드 어 셈블리 M2x3 2 USB 3.1 Type-C 포트 브래 시스템 보드 킷 M2x3 2 힌지 브래킷 손목 받침대 및 키보드 어 셈블리 M2.5x5 4 힌지 브래킷 디스플레이 패널 M2.5x2.5 빅헤드 12 힌지 브래킷 디스플레이 패널 M2x2.5 2 I/O 보드 손목 받침대 및 키보드 어 셈블리 M2x3 2 시스템 보드 KB 지원 M2L2 빅헤드 2 Inspiron 5500의 주요 구성 요소 다음 이미지에서는 Inspiron 5500의 주요 구성 요소를 보여줍니다.
1. 베이스 커버 2. 전원 어댑터 포트 3. 우측 팬 4. 방열판 5. 메모리 모듈(DIMM1) 6. 메모리 모듈(DIMM2) 7. 시스템 보드 8. 하드 드라이브 9. 배터리 10. 스피커 11. 터치패드 12. 터치패드 브래킷 13. 디스플레이 어셈블리 14. 팜레스트 및 키보드 어셈블리 15. M.2 2280 솔리드 스테이트 드라이브 16. 열 실드 17. M.2 2230 솔리드 스테이트 드라이브 18. 열 실드 19. 무선 카드 20. 좌측 팬 21. I/O 보드 22. 지문 인식기가 장착된 전원 버튼 노트: Dell은 구매한 원래 시스템 구성의 구성 요소 및 부품 번호 목록을 제공합니다. 이러한 부품은 고객이 구매한 보증 기간에 따라 사용할 수 있습니다. 구매 옵션은 Dell 영업 담당자에게 문의하십시오.
베이스 덮개 베이스 커버 제거 전제조건 1. 컴퓨터 내부 작업을 시작하기 전에의 절차를 따릅니다. 이 작업 정보 다음 그림은 베이스 커버의 위치를 나타내고 제거 절차를 시각적으로 보여 줍니다.
구성 요소 제거 및 설치 13
단계 1. 베이스 커버를 팜레스트 및 키보드 어셈블리에 고정하는 4개의 캡티브 나사를 풉니다. 2. 베이스 커버를 팜레스트 및 키보드 어셈블리에 고정하는 6개의 나사(M2x7)를 제거합니다. 주의: 베이스 커버가 손상될 수 있으므로 힌지가 있는 측면에서 베이스 커버를 잡아 당기거나 들어 올리지 마십시오. 3. 플라스틱 스크라이브를 사용하여 베이스 커버를 왼쪽 상단 모서리부터 화살표 방향으로 들어 올려 팜레스트 및 키보드 어셈블리 에서 베이스 커버를 분리합니다. 4. 베이스 커버를 들어 올려 뒤집습니다. 노트: 다음 단계는 컴퓨터에서 기타 구성 요소를 추가로 제거하려는 경우에만 적용됩니다. 5. 해당하는 경우, 시스템 보드에서 LED 케이블을 연결 해제합니다. 6. 당김 탭을 사용하여 배터리 케이블을 시스템 보드에서 연결 해제합니다. 7. 컴퓨터를 뒤집고 약 15초간 전원 버튼을 눌러 잔류 전원을 방전시킵니다.
구성 요소 제거 및 설치 15
단계 1. 해당하는 경우, 배터리 케이블을 시스템 보드에 연결합니다. 2. 해당하는 경우, LED 케이블을 시스템 보드에 연결합니다. 3. 베이스 커버의 나사 구멍을 팜레스트 및 키보드 어셈블리의 나사 구멍에 맞춘 다음 베이스 커버를 제자리에 끼웁니다. 4. 베이스 커버를 팜레스트 및 키보드 어셈블리에 고정하는 6개의 나사(M2x7)를 장착합니다. 5. 베이스 커버를 팜레스트 및 키보드 어셈블리에 고정하는 4개의 조임 나사를 조입니다. 다음 단계 1. 컴퓨터 내부 작업을 마친 후에의 절차를 따릅니다. 표시등 막대 표시등 막대 제거 전제조건 1. 컴퓨터 내부 작업을 시작하기 전에의 절차를 따릅니다. 2. 베이스 커버를 제거합니다. 노트: 이 절차는 Nvidia GeForce GTX 1650 Ti/Nvidia GeForce RTX 2060/Nvidia GeForce RTX 2070 MQ와 함께 제공되는 컴퓨터에 만 적용됩니다.
이 작업 정보 다음 그림은 베이스 커버의 위치를 나타내고 제거 절차를 시각적으로 보여 줍니다. 단계 1. 표시등 막대를 베이스 커버에 고정하는 7개의 나사(M2x3)를 제거합니다. 2. 표시등 막대를 들어 올려 베이스 커버에서 분리합니다. 표시등 막대 설치 전제조건 구성 요소를 교체하는 경우 설치 절차를 수행하기 전에 기존 구성 요소부터 제거합니다. 이 작업 정보 노트: 이 절차는 Nvidia GeForce GTX 1650 Ti/Nvidia GeForce RTX 2060/Nvidia GeForce RTX 2070 MQ와 함께 제공되는 컴퓨터에 만 적용됩니다. 다음 그림은 베이스 커버의 위치를 나타내고 설치 절차를 시각적으로 보여 줍니다.
단계 1. 표시등 막대의 나사 구멍을 베이스 커버의 나사 구멍에 맞춥니다. 2. 표시등 막대를 베이스 커버에 고정하는 7개의 나사(M2x3)를 장착합니다. 다음 단계 1. 베이스 커버를 설치합니다. 2. 컴퓨터 내부 작업을 마친 후에의 절차를 따릅니다. 메모리 모듈 메모리 모듈 제거 전제조건 1. 컴퓨터 내부 작업을 시작하기 전에의 절차를 따릅니다. 2. 베이스 커버를 제거합니다. 이 작업 정보 다음 그림은 메모리 모듈의 위치를 나타내고 제거 절차를 시각적으로 보여줍니다.
단계 1. 마일라를 뒤집어 메모리 모듈을 찾습니다. 2. 메모리 모듈이 튀어 나올 때까지 메모리 모듈 슬롯의 양쪽 끝에 있는 고정 클립을 손끝으로 조심스럽게 벌립니다. 3. 메모리 모듈 슬롯에서 메모리 모듈을 분리합니다. 메모리 모듈 설치 전제조건 구성 요소를 교체하는 경우 설치 절차를 수행하기 전에 기존 구성 요소부터 제거합니다. 이 작업 정보 다음 그림은 메모리 모듈의 위치를 나타내고 설치 절차를 시각적으로 보여 줍니다.
단계 1. 마일라를 뒤집어 메모리 모듈 슬롯을 찾습니다. 2. 메모리 모듈의 노치를 메모리 모듈 슬롯의 탭에 맞춥니다. 3. 메모리 모듈을 일정한 각도로 슬롯에 단단히 밀어 넣습니다. 4. 딸깍 소리가 나면서 제자리에 고정될 때까지 메모리 모듈을 아래로 누릅니다. 노트: 소리가 나지 않으면 메모리 모듈을 제거했다가 다시 설치합니다. 다음 단계 1. 베이스 커버를 설치합니다. 2. 컴퓨터 내부 작업을 마친 후에의 절차를 따릅니다. 솔리드 - 스테이트 드라이브 - M.2 슬롯 1 M.2 슬롯 1에서 2230 솔리드 스테이트 드라이브 제거 전제조건 1. 컴퓨터 내부 작업을 시작하기 전에의 절차를 따릅니다. 2. 베이스 커버를 제거합니다. 이 작업 정보 노트: 이 절차는 M.2 슬롯 1에 설치된 2230 솔리드 스테이트 드라이브가 함께 제공되는 컴퓨터에만 적용됩니다. 노트: 주문한 구성에 따라 컴퓨터에 다음 중 하나가 설치된 상태로 배송될 수 있습니다.
다음 이미지는 M.2 슬롯 1에 설치된 2230 솔리드 스테이트 드라이브의 위치를 나타내고 제거 절차를 시각적으로 보여줍니다. 단계 1. 열 실드를 솔리드 스테이트 드라이브 및 시스템 보드에 고정하는 2개의 나사(M2x3)를 제거합니다. 2. 열 실드를 팜레스트 및 키보드 어셈블리에서 들어 올립니다. 3. 솔리드 스테이트 드라이브를 팜레스트 및 키보드 어셈블리에 고정하는 나사(M2x3)를 제거합니다. 4. 솔리드 스테이트 드라이브를 밀어 시스템 보드의 SSD1 슬롯에서 들어 올립니다. M.2 슬롯 1에 2230 솔리드 스테이트 드라이브 설치 전제조건 구성 요소를 교체하는 경우 설치 절차를 수행하기 전에 기존 구성 요소부터 제거합니다. 이 작업 정보 노트: 이 절차는 M.2 슬롯 1에 설치된 2230 솔리드 스테이트 드라이브가 함께 제공되는 컴퓨터에만 적용됩니다. 노트: 주문한 구성에 따라 컴퓨터에 다음 중 하나가 설치된 상태로 배송될 수 있습니다.
단계 1. 솔리드 스테이트 드라이브 마운팅 브래킷을 시스템 보드의 슬롯으로 밀어 넣습니다(설치되어 있지 않은 경우). 2. 솔리드 스테이트 드라이브의 노치를 시스템 보드의 SSD1 슬롯에 맞춥니다. 3. 솔리드 스테이트 드라이브를 시스템 보드의 SSD1 슬롯으로 밀어 넣습니다. 4. 솔리드 스테이트 드라이브를 시스템 보드에 고정하는 나사(M2x3)를 장착합니다. 5. 열 실드를 솔리드 스테이트 드라이브에 놓습니다. 6. 열 실드의 나사 구멍을 시스템 보드의 나사 구멍과 팜레스트 및 키보드 어셈블리에 맞춥니다. 7. 열 실드를 솔리드 스테이트 드라이브 및 시스템 보드에 고정하는 2개의 나사(M2x3)를 장착합니다. 다음 단계 1. 베이스 커버를 설치합니다. 2. 컴퓨터 내부 작업을 마친 후에의 절차를 따릅니다. M.2 슬롯 1에서 2280 솔리드 스테이트 드라이브/인텔 옵테인 제거 전제조건 1. 컴퓨터 내부 작업을 시작하기 전에의 절차를 따릅니다.
2. 베이스 커버를 제거합니다. 이 작업 정보 노트: 이 절차는 M.2 슬롯 1에 설치된 2280 솔리드 스테이트 드라이브가 함께 제공되는 컴퓨터에만 적용됩니다. 노트: 주문한 구성에 따라 컴퓨터에 다음 중 하나가 설치된 상태로 배송될 수 있습니다. ● 1개의 하드 드라이브 및 1개의 2230 또는 2280 솔리드 스테이트 드라이브 ● 1개의 2230 솔리드 스테이트 드라이브 및 1개의 2280 솔리드 스테이트 드라이브 노트: 주문한 구성에 따라 컴퓨터는 M.2 슬롯 1에서 2230 솔리드 스테이트 드라이브 또는 2280 솔리드 스테이트 드라이브를 지 원할 수 있습니다. 다음 이미지는 M.2 슬롯 1에 설치된 2280 솔리드 스테이트 드라이브/인텔 옵테인의 위치를 나타내고 제거 절차를 시각적으로 보여줍 니다. 단계 1. 열 실드를 시스템 보드와 팜레스트 및 키보드 어셈블리에 고정하는 2개의 M2x3 나사를 제거합니다. 2. 열 실드를 팜레스트 및 키보드 어셈블리에서 들어 올립니다. 3.
노트: 주문한 구성에 따라 컴퓨터는 M.2 슬롯 1에서 2230 솔리드 스테이트 드라이브 또는 2280 솔리드 스테이트 드라이브를 지 원할 수 있습니다. 다음 이미지는 M.2 슬롯 1에 설치된 2280 솔리드 스테이트 드라이브/인텔 옵테인의 위치를 나타내고 설치 절차를 시각적으로 보여줍 니다. 단계 1. 솔리드 스테이트 드라이브/인텔 옵테인의 노치를 시스템 보드의 SSD2 슬롯에 맞춥니다. 2. 솔리드 스테이트 드라이브/인텔 옵테인을 시스템 보드의 SSD2 슬롯으로 밀어 넣습니다. 3. 솔리드 스테이트 드라이브 브래킷을 솔리드 스테이트 드라이브/인텔 옵테인에 놓습니다. 4. 열 실드의 나사 구멍을 시스템 보드의 나사 구멍과 팜레스트 및 키보드 어셈블리에 맞춥니다. 5. 솔리드 스테이트 드라이브/인텔 옵테인을 시스템 보드에 고정하는 2개의 나사(M2x3)를 장착합니다. 다음 단계 1. 베이스 커버를 설치합니다. 2. 컴퓨터 내부 작업을 마친 후에의 절차를 따릅니다. 솔리드 - 스테이트 드라이브 - M.
● 1개의 2230 솔리드 스테이트 드라이브 및 1개의 2280 솔리드 스테이트 드라이브 단계 1. 솔리드 스테이트 드라이브 브래킷을 시스템 보드와 팜레스트 및 키보드 어셈블리에 고정하는 2개의 나사(M2x3)를 제거합니다. 2. 솔리드 스테이트 드라이브 브래킷을 들어 올려 솔리드 스테이트 드라이브에서 분리합니다. 3. 솔리드 스테이트 드라이브를 밀어 시스템 보드의 SSD2 슬롯에서 들어 올립니다. M.2 슬롯 2에 2280 솔리드 스테이트 드라이브 설치 전제조건 구성 요소를 교체하는 경우 설치 절차를 수행하기 전에 기존 구성 요소부터 제거합니다. 이 작업 정보 다음 이미지는 M.2 슬롯 2에 설치된 2280 솔리드 스테이트 드라이브의 위치를 나타내고 설치 절차를 시각적으로 보여줍니다. 노트: 주문한 구성에 따라 컴퓨터에 다음 중 하나가 설치된 상태로 배송될 수 있습니다.
단계 1. 솔리드 스테이트 드라이브의 노치를 시스템 보드의 SSD2 슬롯에 맞춥니다. 2. 솔리드 스테이트 드라이브를 시스템 보드의 SSD2 슬롯에 밀어 넣습니다. 3. 솔리드 스테이트 드라이브 브래킷을 솔리드 스테이트 드라이브에 놓습니다. 4. 솔리드 스테이트 드라이브 브래킷의 나사 구멍을 시스템 보드와 팜레스트 및 키보드 어셈블리의 나사 구멍에 맞춥니다. 5. 솔리드 스테이트 드라이브를 시스템 보드에 고정하는 2개의 M2x3 나사를 장착합니다. 다음 단계 1. 베이스 커버를 설치합니다. 2. 컴퓨터 내부 작업을 마친 후에의 절차를 따릅니다. 하드 드라이브 하드 드라이브 분리 전제조건 1. 컴퓨터 내부 작업을 시작하기 전에의 절차를 따릅니다. 2. 베이스 커버를 제거합니다. 이 작업 정보 다음 이미지는 하드 드라이브의 위치를 나타내고 제거 절차를 시각적으로 보여 줍니다. 노트: 주문한 구성에 따라 컴퓨터에 다음 중 하나가 설치된 상태로 배송될 수 있습니다.
단계 1. 래치를 열고 시스템 보드에서 하드 드라이브 케이블을 분리합니다. 2. 하드 드라이브 어셈블리를 팜레스트 및 키보드 어셈블리에 고정하는 3개의 나사(M2x3)를 제거합니다. 3. 하드 드라이브 어셈블리를 케이블과 함께 들어 올려 팜레스트 및 키보드 어셈블리에서 분리합니다. 4. 하드 드라이브 어셈블리에서 인터포저를 분리합니다. 5. 하드 드라이브 브래킷을 하드 드라이브에 고정시키는 4개의 나사(M3x3)를 분리합니다. 6. 하드 드라이브 브래킷에서 하드 드라이브를 분리합니다. 하드 드라이브 설치 전제조건 구성 요소를 교체하는 경우 설치 절차를 수행하기 전에 기존 구성 요소부터 제거합니다. 이 작업 정보 다음 이미지는 하드 드라이브의 위치를 나타내고 설치 절차를 시각적으로 보여 줍니다. 노트: 주문한 구성에 따라 컴퓨터에 다음 중 하나가 설치된 상태로 배송될 수 있습니다.
● 1개의 2230 솔리드 스테이트 드라이브 및 1개의 2280 솔리드 스테이트 드라이브 단계 1. 하드 드라이브 브래킷의 나사 구멍을 하드 드라이브의 나사 구멍에 맞춥니다. 2. 하드 드라이브 브래킷을 하드 드라이브에 고정시키는 4개의 나사(M3x3)를 장착합니다. 3. 하드 드라이브 어셈블리에 인터포저를 연결합니다. 4. 하드 드라이브 어셈블리의 나사 구멍을 팜레스트 및 키보드 어셈블리의 나사 구멍에 맞춥니다. 5. 하드 드라이브 어셈블리를 팜레스트 및 키보드 어셈블리에 고정하는 3개의 나사(M2x3)를 장착합니다. 6. 하드 드라이브 케이블을 시스템 보드에 연결하고 래치를 닫아 케이블을 고정합니다. 다음 단계 1. 베이스 커버를 설치합니다. 2. 컴퓨터 내부 작업을 마친 후에의 절차를 따릅니다.
배터리 3셀 배터리 제거 전제조건 1. 컴퓨터 내부 작업을 시작하기 전에의 절차를 따릅니다. 2. 베이스 커버를 제거합니다. 이 작업 정보 다음 이미지는 배터리의 위치를 나타내고 제거 절차를 시각적으로 보여 줍니다. 단계 1. 배터리를 팜레스트 및 키보드 어셈블리에 고정하는 2개의 나사(M2x3)를 제거합니다. 2. 해당하는 경우, 시스템 보드에서 배터리 케이블을 연결 해제합니다. 3. 배터리를 들어 올려 팜레스트 및 키보드 어셈블리에서 분리합니다. 3셀 배터리 설치 전제조건 구성 요소를 교체하는 경우 설치 절차를 수행하기 전에 기존 구성 요소부터 제거합니다. 이 작업 정보 다음 그림은 배터리의 위치를 나타내고 설치 절차를 시각적으로 보여 줍니다.
단계 1. 배터리의 나사 구멍을 팜레스트 및 키보드 어셈블리의 나사 구멍에 맞춥니다. 2. 배터리를 팜레스트 및 키보드 어셈블리에 고정하는 2개의 나사(M2x3)를 장착합니다. 3. 배터리 케이블을 시스템 보드에 연결합니다. 다음 단계 1. 베이스 커버를 설치합니다. 2. 컴퓨터 내부 작업을 마친 후에의 절차를 따릅니다. 4셀 배터리 제거 전제조건 1. 컴퓨터 내부 작업을 시작하기 전에의 절차를 따릅니다. 2. 베이스 커버를 제거합니다. 이 작업 정보 다음 이미지는 배터리의 위치를 나타내고 제거 절차를 시각적으로 보여 줍니다.
단계 1. 배터리를 팜레스트 및 키보드 어셈블리에 고정하는 3개의 나사(M2x3)를 제거합니다. 2. 해당하는 경우, 시스템 보드에서 배터리 케이블을 연결 해제합니다. 3. 배터리를 들어 올려 팜레스트 및 키보드 어셈블리에서 분리합니다. 4셀 배터리 설치 전제조건 구성 요소를 교체하는 경우 설치 절차를 수행하기 전에 기존 구성 요소부터 제거합니다. 이 작업 정보 다음 그림은 배터리의 위치를 나타내고 설치 절차를 시각적으로 보여 줍니다.
단계 1. 배터리의 나사 구멍을 팜레스트 및 키보드 어셈블리의 나사 구멍에 맞춥니다. 2. 배터리를 팜레스트 및 키보드 어셈블리에 고정하는 3개의 나사(M2x3)를 장착합니다. 3. 배터리 케이블을 시스템 보드에 연결합니다. 다음 단계 1. 베이스 커버를 설치합니다. 2. 컴퓨터 내부 작업을 마친 후에의 절차를 따릅니다. 무선 카드 WLAN 카드 제거 전제조건 1. 컴퓨터 내부 작업을 시작하기 전에의 절차를 따릅니다. 2. 베이스 커버를 제거합니다. 이 작업 정보 다음 그림은 WLAN 카드의 위치를 나타내고 제거 절차를 시각적으로 보여 줍니다.
단계 1. WLAN 카드를 시스템 보드에 고정하는 나사(M2x3)를 제거합니다. 2. WLAN 카드를 시스템 보드에 고정하는 브래킷을 제거합니다. 3. 안테나 케이블을 WLAN 카드에서 연결 해제합니다. 4. WLAN 카드를 밀어 WLAN 카드 슬롯에서 제거합니다. WLAN 카드 설치 전제조건 구성 요소를 교체하는 경우 설치 절차를 수행하기 전에 기존 구성 요소부터 제거합니다. 이 작업 정보 다음 그림은 WLAN 카드의 위치를 나타내고 설치 절차를 시각적으로 보여 줍니다.
단계 1. WLAN 카드에 안테나 케이블을 연결합니다. 다음 표에는 컴퓨터에서 지원되는 무선 카드의 안테나 케이블 색상표가 제공됩니다. 표 2. 안테나 케이블 색상표 무선 카드의 커넥터 안테나 케이블 색상 주(흰색 삼각형) 흰색 보조(검정색 삼각형) 검정색 2. WLAN 카드의 노치를 WLAN 카드 슬롯의 탭에 맞춘 후 WLAN 카드를 일정한 각도로 WLAN 카드 슬롯에 삽입합니다. 3. WLAN 카드 브래킷을 WLAN 카드에 맞추어 놓습니다. 4. 나사(M2x3)를 장착하여 WLAN 카드를 시스템 보드에 고정합니다. 다음 단계 1. 베이스 커버를 설치합니다. 2. 컴퓨터 내부 작업을 마친 후에의 절차를 따릅니다.
스피커 스피커 제거 전제조건 1. 컴퓨터 내부 작업을 시작하기 전에의 절차를 따릅니다. 2. 베이스 커버를 제거합니다. 이 작업 정보 다음 그림은 스피커의 위치를 나타내고 제거 절차를 시각적으로 보여 줍니다. 단계 1. 시스템 보드에서 스피커 케이블을 분리합니다. 2. 왼쪽 스피커를 오른쪽 스피커에 연결하는 케이블의 라우팅을 기록하고 팜레스트 및 키보드 어셈블리의 라우팅 가이드에서 제거 합니다. 노트: 스피커를 들어 올리기 전에 고무 그로밋의 위치를 기록합니다. 3. 스피커와 해당 케이블을 함께 들어 올려 팜레스트 및 키보드 어셈블리에서 분리합니다. 스피커 설치 전제조건 구성 요소를 교체하는 경우 설치 절차를 수행하기 전에 기존 구성 요소부터 제거합니다. 이 작업 정보 다음 그림은 스피커의 위치를 나타내고 설치 절차를 시각적으로 보여 줍니다.
단계 1. 정렬 포스트 및 고무 그로밋을 사용하여 스피커를 팜레스트 및 키보드 어셈블리의 슬롯에 끼워 넣습니다. 노트: 스피커 제거 시 고무 그로밋이 스피커에서 빠져나온 상태라면 스피커를 장착하기 전에 제자리에 밀어 넣습니다. 2. 팜레스트 및 키보드 어셈블리의 라우팅 가이드를 통해 스피커 케이블을 라우팅합니다. 3. 시스템 보드에 스피커 케이블을 연결합니다. 다음 단계 1. 베이스 커버를 설치합니다. 2. 컴퓨터 내부 작업을 마친 후에의 절차를 따릅니다. 코인 셀 배터리 코인 셀 배터리 제거 전제조건 1. 컴퓨터 내부 작업을 시작하기 전에의 절차를 따릅니다. 2. 베이스 커버를 제거합니다. 이 작업 정보 다음 그림은 코인 셀 배터리의 위치를 나타내고 제거 절차를 시각적으로 보여줍니다.
단계 플라스틱 스크라이브를 사용하여 코인 셀 배터리를 시스템 보드의 코인 셀 배터리 슬롯에서 들어 올립니다. 코인 셀 배터리 설치 전제조건 구성 요소를 교체하는 경우 설치 절차를 수행하기 전에 기존 구성 요소부터 제거합니다. 이 작업 정보 다음 그림은 코인 셀 베터리의 위치를 나타내고 설치 절차를 시각적으로 보여 줍니다.
단계 1. 코인 셀 배터리를 양극 면이 위로 향하도록 하여 코인 셀 배터리 슬롯에 놓습니다. 2. 코인 셀 배터리를 제자리에 끼웁니다. 다음 단계 1. 베이스 커버를 설치합니다. 2. 컴퓨터 내부 작업을 마친 후에의 절차를 따릅니다. 전원 어댑터 포트 전원 어댑터 포트 제거 전제조건 1. 컴퓨터 내부 작업을 시작하기 전에의 절차를 따릅니다. 2. 베이스 커버를 제거합니다. 이 작업 정보 다음 그림은 전원 어댑터 포트의 위치를 나타내고 제거 절차를 시각적으로 보여 줍니다. 단계 1. 전원 어댑터 포트를 시스템 보드에 고정하는 전원 어댑터 포트 브래킷에서 나사(M2x3)를 제거합니다. 2. 시스템 보드에서 전원 어댑터 포트 브래킷을 제거합니다. 3. 시스템 보드의 전원 어댑터 포트 케이블 연결부를 덮고 있는 마일라를 떼어냅니다. 4. 전원 어댑터 포트 케이블을 시스템 보드에 고정하는 테이프를 다시 떼어냅니다. 5. 시스템 보드에서 전원 어댑터 포트 케이블을 연결 해제합니다. 6.
전원 어댑터 포트 설치 전제조건 구성 요소를 교체하는 경우 설치 절차를 수행하기 전에 기존 구성 요소부터 제거합니다. 이 작업 정보 다음 그림은 전원 어댑터 포트의 위치를 나타내고 설치 절차를 시각적으로 보여 줍니다. 단계 1. 전원 어댑터 포트를 해당 슬롯에 밀어 넣고 전원 어댑터 포트 케이블을 팜레스트 및 키보드 어셈블리에 부착합니다. 2. 전원 어댑터 포트 케이블을 시스템 보드에 연결합니다. 3. 시스템 보드의 전원 어댑터 포트 케이블 연결부를 덮는 마일라를 부착합니다. 4. 전원 어댑터 포트 브래킷을 전원 어댑터 포트 위에 맞추어 놓습니다. 5. 전원 어댑터 포트 브래킷을 시스템 보드에 고정하는 2개의 나사(M2x3)를 장착합니다. 다음 단계 1. 베이스 커버를 설치합니다. 2. 컴퓨터 내부 작업을 마친 후에의 절차를 따릅니다. 팬 좌측 팬 제거 전제조건 1. 컴퓨터 내부 작업을 시작하기 전에의 절차를 따릅니다. 2. 베이스 커버를 제거합니다.
이 작업 정보 다음 그림은 왼쪽 팬의 위치를 나타내고 제거 절차를 시각적으로 보여 줍니다. 단계 1. 시스템 보드에서 팬 케이블을 분리합니다. 2. WLAN 케이블의 라우팅 경로를 기록해 두고 왼쪽 팬에서 WLAN 케이블을 제거합니다. 3. 왼쪽 팬을 시스템 보드에 고정하는 2개의 M2x3 나사를 제거합니다. 4. 왼쪽 팬을 들어 올려 팜레스트 및 키보드 어셈블리에서 분리합니다. 왼쪽 팬 설치 전제조건 구성 요소를 교체하는 경우 설치 절차를 수행하기 전에 기존 구성 요소부터 제거합니다. 이 작업 정보 다음 그림은 왼쪽 팬의 위치를 나타내고 설치 절차를 시각적으로 보여 줍니다.
단계 1. 왼쪽 팬을 팜레스트 및 키보드 어셈블리에 맞추어 놓습니다. 2. 팬의 라우팅 가이드를 통해 WLAN 케이블을 라우팅합니다. 3. 좌측 팬 케이블을 시스템 보드에 연결합니다. 4. 왼쪽 팬을 팜레스트 및 키보드 어셈블리에 고정하는 2개의 M2x3 나사를 장착합니다. 다음 단계 1. 베이스 커버를 설치합니다. 2. 컴퓨터 내부 작업을 마친 후에의 절차를 따릅니다. 오른쪽 팬 제거 전제조건 1. 컴퓨터 내부 작업을 시작하기 전에의 절차를 따릅니다. 2. 베이스 커버를 제거합니다.
이 작업 정보 다음 그림은 오른쪽 팬의 위치를 나타내고 설치 절차를 시각적으로 보여 줍니다. 단계 1. 시스템 보드에서 우측 팬 케이블을 분리합니다. 2. 오른쪽 팬을 시스템 보드에 고정하는 2개의 M2x3 나사를 제거합니다. 3. 오른쪽 팬을 들어 올려 팜레스트 및 키보드 어셈블리에서 분리합니다. 오른쪽 팬 설치 전제조건 구성 요소를 교체하는 경우 설치 절차를 수행하기 전에 기존 구성 요소부터 제거합니다. 이 작업 정보 다음 그림은 오른쪽 팬의 위치를 나타내고 설치 절차를 시각적으로 보여 줍니다.
단계 1. 오른쪽 팬을 팜레스트 및 키보드 어셈블리에 맞추어 놓습니다. 2. 오른쪽 팬을 팜레스트 및 키보드 어셈블리에 고정하는 2개의 M2x3 나사를 장착합니다. 3. 우측 팬 케이블을 시스템 보드에 연결합니다. 다음 단계 1. 베이스 커버를 설치합니다. 2. 컴퓨터 내부 작업을 마친 후에의 절차를 따릅니다. 방열판 방열판 제거 전제조건 1. 컴퓨터 내부 작업을 시작하기 전에의 절차를 따릅니다. 주의: 프로세서의 최대 냉각 기능을 보장하려면 프로세서 방열판의 열 전달 영역을 만지지 마십시오. 피부에 묻어있는 오일 은 열 그리스의 열 전달 기능을 저하시킬 수 있습니다. 노트: 방열판은 정상 작동 중에 뜨거워질 수 있습니다. 충분한 시간 동안 방열판을 식힌 후에 만지도록 하십시오. 2. 베이스 커버를 제거합니다. 이 작업 정보 다음 그림은 방열판의 위치를 나타내고 제거 절차를 시각적으로 보여 줍니다.
단계 1. 방열판을 시스템 보드에 고정하는 8개의 조임 나사를 반대 순서로(8>7>6>5>4>3>2>1) 풉니다. 2. 방열판을 들어 올려 시스템 보드에서 분리합니다. 방열판 설치 전제조건 구성 요소를 교체하는 경우 설치 절차를 수행하기 전에 기존 구성 요소부터 제거합니다. 이 작업 정보 다음 그림은 방열판의 위치를 나타내고 설치 절차를 시각적으로 보여 줍니다. 주의: 방열판을 잘못 맞추면 시스템 보드 및 프로세서가 손상될 수 있습니다. 노트: 시스템 보드 또는 방열판을 장착할 경우 키트에 제공된 방열 패드/붙여넣기를 사용하여 열 전도성을 확보합니다.
단계 1. 방열판을 시스템 보드에 놓고 방열판의 나사 구멍을 시스템 보드의 나사 구멍에 맞춥니다. 2. 방열판에 표시된 번호 순서대로 방열판을 시스템 보드에 고정하는 8개의 조임 나사를 조입니다. 다음 단계 1. 베이스 커버를 설치합니다. 2. 컴퓨터 내부 작업을 마친 후에의 절차를 따릅니다. I/O 보드 I/O 보드 분리 전제조건 1. 컴퓨터 내부 작업을 시작하기 전에의 절차를 따릅니다. 2. 베이스 커버를 제거합니다. 3. 왼쪽 팬을 제거합니다.
이 작업 정보 다음 그림은 I/O 보드의 위치를 나타내고 제거 절차를 시각적으로 보여 줍니다. 단계 1. 래치를 들어 올려 I/O 보드 케이블을 I/O 보드에서 연결 해제합니다. 2. I/O 보드를 팜레스트 및 키보드 어셈블리에 고정하는 3개의 나사(M2x3)를 제거합니다. 3. I/O 보드를 들어 올려 팜레스트 및 키보드 어셈블리에서 분리합니다. I/O 보드 설치 전제조건 구성 요소를 교체하는 경우 설치 절차를 수행하기 전에 기존 구성 요소부터 제거합니다. 이 작업 정보 다음 그림은 I/O 보드의 위치를 나타내고 설치 절차를 시각적으로 보여 줍니다.
단계 1. I/O 보드를 팜레스트 및 키보드 어셈블리에 맞추어 놓습니다. 2. I/O 보드를 팜레스트 및 키보드 어셈블리에 고정하는 3개의 나사(M2x3)를 설치합니다. 3. I/O 보드 케이블을 I/O 보드에 연결합니다. 다음 단계 1. 왼쪽 팬을 설치합니다. 2. 베이스 커버를 설치합니다. 3. 컴퓨터 내부 작업을 마친 후에의 절차를 따릅니다. 디스플레이 어셈블리 디스플레이 어셈블리 제거 전제조건 1. 컴퓨터 내부 작업을 시작하기 전에의 절차를 따릅니다. 2. 베이스 커버를 제거합니다. 3. 방열판을 분리합니다.
이 작업 정보 다음 그림은 디스플레이 어셈블리의 위치를 나타내고 제거 절차를 시각적으로 보여줍니다. 단계 1. 시스템 보드에서 디스플레이 케이블을 분리합니다. 2. 디스플레이 힌지를 시스템 보드에 고정하는 4개의 나사(M2.5x5)를 제거합니다. 3. 팜레스트 및 키보드 어셈블리에서 디스플레이 어셈블리를 들어 올립니다.
디스플레이 어셈블리 설치 전제조건 구성 요소를 교체하는 경우 설치 절차를 수행하기 전에 기존 구성 요소부터 제거합니다. 이 작업 정보 이 그림은 디스플레이 어셈블리의 위치를 나타내고 설치 절차를 시각적으로 보여 줍니다.
단계 1. 디스플레이 어셈블리를 팜레스트 및 키보드 어셈블리에 맞춥니다. 2. 디스플레이 힌지의 나사 구멍을 시스템 보드의 나사 구멍에 맞춥니다. 3. 디스플레이 힌지를 시스템 보드에 고정하는 4개의 나사(M2.5x5)를 장착합니다. 4. 디스플레이 케이블을 시스템 보드에 연결합니다. 다음 단계 1. 방열판을 설치합니다. 2. 베이스 커버를 설치합니다. 3. 컴퓨터 내부 작업을 마친 후에의 절차를 따릅니다. 시스템 보드 시스템 보드 제거 전제조건 1. 2. 3. 4. 5. 6. 7. 8. 9. 컴퓨터 내부 작업을 시작하기 전에의 절차를 따릅니다. 베이스 커버를 제거합니다. 배터리를 제거합니다. 솔리드 스테이트 드라이브/인텔 옵테인을 제거합니다. WLAN 카드를 제거합니다. 오른쪽 팬을 제거합니다. 방열판을 분리합니다. 전원 어댑터 포트를 분리합니다. 하드 드라이브를 분리합니다. 이 작업 정보 다음 그림은 시스템 보드의 위치를 나타내고 제거 절차를 시각적으로 보여 줍니다.
주의: I/O 보드 커넥터는 시스템 보드 아래에 있습니다. 시스템 보드를 뒤집고 I/O 보드 케이블을 시스템 보드에서 연결 해제합니다.
단계 1. 래치를 열고 시스템 보드에서 전원 버튼 케이블을 분리합니다. 2. 래치를 열고 시스템 보드에서 키보드 케이블을 분리합니다. 3. 래치를 열고 시스템 보드에서 키보드 백라이트 케이블을 분리합니다. 4. 래치를 열고 시스템 보드에서 터치패드 케이블을 연결 해제합니다. 5. 시스템 보드에서 스피커 케이블을 분리합니다. 6. 시스템 보드를 팜레스트 및 키보드 어셈블리에 고정하는 2개의 M2x2 나사를 제거합니다. 7. 시스템 보드를 뒤집고 I/O 보드 케이블을 시스템 보드에서 연결 해제합니다. 시스템 보드 설치 전제조건 구성 요소를 교체하는 경우 설치 절차를 수행하기 전에 기존 구성 요소부터 제거합니다. 이 작업 정보 다음 그림은 시스템 보드의 위치를 나타내고 설치 절차를 시각적으로 보여 줍니다. 노트: I/O 보드 커넥터는 시스템 보드 아래에 있습니다. 시스템 보드를 뒤집고 I/O 보드 케이블을 시스템 보드에 연결합니다.
단계 1. I/O 보드 케이블을 시스템 보드에 연결합니다. 2. 시스템 보드를 전면으로 돌리고 시스템 보드를 팜레스트 및 키보드 어셈블리에 맞추어 놓습니다. 3. 시스템 보드를 팜레스트 및 키보드 어셈블리에 고정하는 2개의 M2x2 나사를 장착합니다. 4. 시스템 보드에 스피커 케이블을 연결합니다. 5. 래치를 열고 터치패드 케이블을 시스템 보드에 연결합니다. 6. 래치를 열고 키보드 백라이트 케이블을 시스템 보드에 연결합니다. 7. 래치를 열고 키보드 케이블을 시스템 보드에 연결합니다. 8. 래치를 열고 전원 버튼 케이블을 시스템 보드에 연결합니다. 다음 단계 1. 2. 3. 4. 5. 6. 7. 8. 9. 하드 드라이브를 설치합니다. 전원 어댑터 포트를 설치합니다. 방열판을 설치합니다. 오른쪽 팬을 설치합니다. WLAN 카드를 설치합니다. 솔리드 스테이트 드라이브/인텔 옵테인을 설치합니다. 배터리를 설치합니다. 베이스 커버를 설치합니다. 컴퓨터 내부 작업을 마친 후에의 절차를 따릅니다.
지문 인식기 도터 보드 지문 인식기가 탑재된 전원 버튼 제거 전제조건 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 컴퓨터 내부 작업을 시작하기 전에의 절차를 따릅니다. 베이스 커버를 제거합니다. 배터리를 제거합니다. 솔리드 스테이트 드라이브/인텔 옵테인을 제거합니다. WLAN 카드를 제거합니다. 오른쪽 팬을 제거합니다. 방열판을 분리합니다. 전원 어댑터 포트를 분리합니다. 하드 드라이브를 분리합니다. 시스템 보드를 제거합니다. 노트: 시스템 보드는 연결된 방열판과 함께 제거할 수 있습니다. 이 작업 정보 다음 그림은 베이스 커버의 위치를 나타내고 제거 절차를 시각적으로 보여 줍니다. 단계 1. 지문 인식기가 장착된 전원 버튼을 팜레스트 및 키보드 어셈블리에 고정하는 2개의 나사(M2x3)를 제거합니다. 2. 지문 인식기가 장착된 전원 버튼을 들어 올려 팜레스트 및 키보드 어셈블리에서 분리합니다.
이 작업 정보 다음 그림은 코인 셀 베터리의 위치를 나타내고 설치 절차를 시각적으로 보여 줍니다. 단계 1. 지문 인식기가 장착된 전원 버튼의 나사 구멍을 팜레스트 및 키보드 어셈블리의 나사 구멍에 맞춥니다. 2. 지문 인식기가 장착된 전원 버튼을 팜레스트 및 키보드 어셈블리에 고정하는 2개의 나사(M2x3)를 장착합니다. 다음 단계 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 시스템 보드를 설치합니다. 하드 드라이브를 설치합니다. 전원 어댑터 포트를 설치합니다. 방열판을 설치합니다. 오른쪽 팬을 설치합니다. WLAN 카드를 설치합니다. 솔리드 스테이트 드라이브/인텔 옵테인을 설치합니다. 배터리를 설치합니다. 베이스 커버를 설치합니다. 컴퓨터 내부 작업을 마친 후에의 절차를 따릅니다. 터치패드 터치패드 제거 전제조건 1. 2. 3. 4. 5. 6. 컴퓨터 내부 작업을 시작하기 전에의 절차를 따릅니다. 베이스 커버를 제거합니다. 배터리를 제거합니다.
7. 8. 9. 10. 11. 방열판을 분리합니다. 하드 드라이브를 분리합니다. 디스플레이 어셈블리를 제거합니다. 전원 어댑터 포트를 분리합니다. 시스템 보드를 제거합니다. 노트: 시스템 보드는 연결된 방열판과 함께 제거할 수 있습니다. 이 작업 정보 다음 그림은 터치패드의 위치를 나타내고 제거 절차를 시각적으로 보여 줍니다. 단계 1. 터치패드 브래킷을 팜레스트 및 키보드 어셈블리에 고정하는 3개의 M2x2 나사를 제거합니다. 2. 터치패드 브래킷을 들어 올려 팜레스트 및 키보드 어셈블리에서 분리합니다. 3. 터치패드에서 테이프를 떼어냅니다. 4. 터치패드를 팜레스트 및 키보드 어셈블리에 고정하는 4개의 M2x2 나사를 제거합니다. 5. 터치패드를 들어 올려 팜레스트 및 키보드 어셈블리에서 분리합니다. 터치패드 설치 전제조건 구성 요소를 교체하는 경우 설치 절차를 수행하기 전에 기존 구성 요소부터 제거합니다.
단계 1. 터치패드를 팜레스트 및 키보드 어셈블리의 슬롯에 맞추어 놓습니다. 2. 4개의 M2x2 나사를 장착하고 터치패드를 팜레스트 및 키보드 어셈블리에 고정하는 테이프를 부착합니다. 3. 터치패드 브래킷을 팜레스트 및 키보드 어셈블리의 슬롯에 맞추어 놓습니다. 4. 터치패드 브래킷을 팜레스트 및 키보드 어셈블리에 고정하는 3개의 M2x2 나사를 장착합니다. 다음 단계 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 시스템 보드를 설치합니다. 전원 어댑터 포트를 설치합니다. 디스플레이 어셈블리를 설치합니다. 오른쪽 팬을 설치합니다. 왼쪽 팬을 설치합니다. WLAN 카드를 설치합니다. 하드 드라이브를 설치합니다. 솔리드 스테이트 드라이브/인텔 옵테인을 설치합니다. 배터리를 설치합니다. 베이스 커버를 설치합니다. 컴퓨터 내부 작업을 마친 후에의 절차를 따릅니다. 손목 받침대 및 키보드 어셈블리 팜레스트 및 키보드 어셈블리 제거 전제조건 1. 2. 3. 4. 5.
6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 왼쪽 팬을 제거합니다. 오른쪽 팬을 제거합니다. 솔리드 스테이트 드라이브/인텔 옵테인을 제거합니다. 하드 드라이브를 분리합니다. I/O 보드를 분리합니다. 터치패드를 제거합니다. 스피커를 분리합니다. 방열판을 분리합니다. 디스플레이 어셈블리를 제거합니다. 전원 어댑터 포트를 분리합니다. 시스템 보드를 제거합니다. 노트: 시스템 보드는 연결된 방열판과 함께 제거할 수 있습니다. 이 작업 정보 사전 요구 사항에 명시된 단계를 수행하고 나면 팜레스트 및 키보드 어셈블리가 남습니다. 팜레스트 및 키보드 어셈블리 설치 전제조건 구성 요소를 교체하는 경우 설치 절차를 수행하기 전에 기존 구성 요소부터 제거합니다. 이 작업 정보 팜레스트 및 키보드 어셈블리를 평평한 표면에 놓습니다.
다음 단계 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 시스템 보드를 설치합니다. 전원 어댑터 포트를 설치합니다. 디스플레이 어셈블리를 설치합니다. 방열판을 설치합니다. 스피커를 설치합니다. 터치패드를 설치합니다. I/O 보드를 설치합니다. 하드 드라이브를 설치합니다. 솔리드 스테이트 드라이브/인텔 옵테인을 설치합니다. 오른쪽 팬을 설치합니다. 왼쪽 팬을 설치합니다. WLAN 카드를 설치합니다. 메모리 모듈을 설치합니다. 배터리를 설치합니다. 베이스 커버를 설치합니다. 컴퓨터 내부 작업을 마친 후에의 절차를 따릅니다.
3 드라이버 및 다운로드 드라이버의 문제를 해결하거나 드라이버를 다운로드 또는 설치하는 경우 Dell 기술 자료 기사, 드라이버 및 다운로드 FAQ SLN128938 을 숙지하는 것이 좋습니다.
4 시스템 설정 주의: 컴퓨터 전문가가 아닌 경우 BIOS 설정 프로그램의 설정을 변경하지 마십시오. 일부 변경 시 컴퓨터가 올바르게 작동하지 않을 수 있습니다. 노트: 컴퓨터 및 장착된 디바이스에 따라 이 섹션에 나열된 항목이 표시될 수도 있고, 표시되지 않을 수도 있습니다. 노트: BIOS 설정 프로그램을 변경하기 전에 나중에 참조할 수 있도록 BIOS 설정 프로그램 화면 정보를 기록해 두는 것이 좋습니 다. BIOS 설정 프로그램은 다음과 같은 용도로 사용합니다. ● 컴퓨터에 설치된 하드웨어의 정보 찾기(예: RAM 용량, 하드 드라이브 크기 등) ● 시스템 구성 정보를 변경합니다. ● 사용자 암호, 설치된 하드 드라이브 유형, 기본 디바이스 활성화 또는 비활성화와 같은 사용자 선택 옵션 설정 또는 변경 BIOS 설정 프로그램 시작하기 단계 1. 컴퓨터를 켭니다. 2. BIOS 설정 프로그램을 시작하려면 즉시 키를 누릅니다.
노트: 컴퓨터가 켜져 있을 경우 컴퓨터를 종료하는 것이 좋습니다. 부팅할 수 있는 장치가 진단 옵션과 함께 원타임 부팅 메뉴에 표시됩니다. 부팅 메뉴 옵션은 다음과 같습니다. ● 이동식 드라이브(사용 가능한 경우) ● STXXXX 드라이브(사용 가능한 경우) 노트: XXX는 SATA 드라이브 번호를 표시합니다. ● 옵티컬 드라이브(사용 가능한 경우) ● SATA 하드 드라이브(사용 가능한 경우) ● 진단 프로그램 노트: 진단을 선택하면, ePSA 진단 화면이 표시됩니다. 부트 순서 화면에는 시스템 설정 화면에 액세스하기 위한 옵션도 표시됩니다. 시스템 설치 옵션 노트: 이 컴퓨터 및 설치된 디바이스에 따라 이 섹션에 나열된 항목이 표시될 수도 있고 표시되지 않을 수도 있습니다. 표 4. 시스템 설치 옵션- 시스템 정보 메뉴 개요 BIOS 버전 BIOS 버전 번호를 표시합니다. 서비스 태그 컴퓨터의 서비스 태그를 표시합니다. 자산 태그 컴퓨터의 자산 태그를 표시합니다.
표 4. 시스템 설치 옵션- 시스템 정보 메뉴 (계속) 개요 인텔 Hyper-Threading 지원 프로세서가 HT(Hyper-Threading)를 지원하는지 여부를 표시합니다. 64비트 기술 64비트 기술을 사용하는지 여부를 표시합니다. 메모리 정보 설치된 메모리 설치된 총 컴퓨터 메모리를 표시합니다. 사용 가능한 메모리 사용 가능한 총 컴퓨터 메모리를 표시합니다. 메모리 속도 메모리 속도를 표시합니다. 메모리 채널 모드 단일 모드 또는 듀얼 채널 모드를 표시합니다. 메모리 기술 메모리에 사용된 기술을 표시합니다. 디바이스 정보 비디오 컨트롤러 컴퓨터의 내장형 그래픽 정보를 표시합니다. dGPU 비디오 컨트롤러 컴퓨터의 독립 그래픽 정보가 표시됩니다. 비디오 BIOS 버전 컴퓨터의 비디오 BIOS 버전을 표시합니다. 비디오 메모리 컴퓨터의 비디오 메모리 정보를 표시합니다. 패널 유형 컴퓨터의 패널 유형을 표시합니다.
표 6. 시스템 설치 옵션—시스템 구성 메뉴 (계속) 시스템 구성 SMART 보고 사용 컴퓨터를 시작하는 동안 SMART(Self-Monitoring, Analysis, and Reporting Technology)를 활성화 또는 비활성화하여 하드 드라이브 오류를 보고합니다. 기본값: 해제 오디오 사용 모든 통합형 오디오 컨트롤러를 활성화 또는 비활성화합니다. 기본값: 설정 마이크로폰 사용 마이크를 활성화 또는 비활성화합니다. 기본값: 설정 내부 스피커 사용 내부 스피커를 활성화 또는 비활성화합니다. 기본값: 설정 USB Configuration Enable Boot Support USB 대용량 스토리지 디바이스(예: 외부 하드 드라이브, 옵티컬 드라이브 및 USB 드라이브)에서의 부팅을 활성화 또는 비활성화합니다. 외부 USB 포트 활성화 운영 체제 환경에서 작동하도록 USB 포트를 활성화 또는 비활성화합니다.
표 7. 시스템 설치 옵션—비디오 메뉴 (계속) 비디오 EcoPower 적절한 경우 화면 밝기를 줄여서 배터리 지속 시간을 증가시키는 EcoPower를 활 성화 또는 비활성화합니다. 기본값: 설정 표 8. 시스템 설치 옵션—보안 메뉴 보안 Enable Admin Setup Lockout(관리자 설정 잠 관리자 암호가 설정되어 있을 때 사용자가 BIOS 설정에 액세스하도록 활성화 또 금 사용) 는 비활성화합니다. 기본값: 해제 Password Bypass 시스템을 재시작하는 동안 시스템(부팅) 암호와 내부 하드 드라이브 암호를 생략 할 수 있습니다. 기본값: 비활성화 Enable Non-Admin Password Changes 사용자가 관리자 암호 없이 시스템 및 하드 드라이브 암호를 변경하도록 활성화 또는 비활성화합니다.
표 8. 시스템 설치 옵션—보안 메뉴 (계속) 보안 System Password 시스템 암호를 설정, 변경 또는 삭제합니다. Enable Master Password Lockout(마스터 암 호 잠금 활성화) 마스터 암호 지원을 활성화 또는 비활성화합니다. 기본값: 해제 표 9. 시스템 설치 옵션—보안 부팅 메뉴 보안 부팅 Enable Secure Boot 검증된 부팅 소프트웨어만 사용하여 부팅하도록 컴퓨터를 활성화 또는 비활성화 합니다. 기본값: 해제 노트: 보안 부팅을 활성화하려면 컴퓨터가 UEFI 부팅 모드에 있어야 하며 레거 시 옵션 ROM 활성화 옵션을 해제해야 합니다. Secure Boot Mode 보안 부팅 작업 모드를 선택합니다. 기본값: 배포된 모드. 노트: 배포된 모드는 보안 부팅의 정상적인 작동을 위해 선택해야 합니다. 표 10.
표 12. 시스템 설치 옵션—전원 관리 메뉴 전원 관리 AC 연결 시 재개 컴퓨터에 AC 전원이 공급되는 경우 컴퓨터가 켜지고 부팅으로 전환하도록 활성화 합니다. 기본값: 해제 Auto On Time 정의된 날짜 및 시간에 자동으로 켜지도록 컴퓨터를 활성화합니다. 기본값: 비활성화 시스템이 자동으로 켜지지 않습니다. Battery Charge Configuration 전원 사용 시간 동안 컴퓨터가 배터리로 실행하도록 활성화합니다. 각 요일의 특정 시간 사이에 AC 전력을 사용하지 못하게 하려면 아래 옵션을 사용합니다. 기본값: 적응형 배터리 설정은 일반적인 배터리 사용 패턴에 따라 적절히 최적화됩 니다. Enable Advanced Battery Charge Configuration 시작 시간부터 지정한 작업 기간까지 Advanced Battery Charge Configuration(고급 배터리 충전 구성) 기능을 활성화합니다.
표 14. 시스템 설치 옵션—POST 동작 메뉴 (계속) POST 동작 기본값: 설정 어댑터 경고 사용 부팅 중에 컴퓨터가 어댑터 경고 메시지를 표시하도록 활성화합니다. 기본값: 설정 Extend BIOS POST Time BIOS POST(Power-On Self-Test) 로드 시간을 구성합니다. 기본값: 0초. Fastboot UEFI 부팅 프로세스의 속도를 구성합니다. 기본: 전체 부팅 중 전체 하드웨어 및 구성 초기화를 수행합니다. Fn Lock Options Fn 잠금 모드를 활성화 또는 비활성화합니다. 기본값: 설정 잠금 모드 기본값: 잠금 모드 보조. 잠금 모드 보조 = 이 옵션이 선택되어 있으면 ~ 키가 코드에서 보조 기능의 코드를 스캐닝합니다. 전체 화면 로고 이미지가 화면 해상도와 일치하는 경우 컴퓨터가 전체 화면 로고를 표시하도록 활 성화 또는 비활성화합니다.
표 16. 시스템 설치 옵션—유지 보수 메뉴 (계속) 유지 보수 기본값: 해제 Start Data Wipe 주의: 이 보안 지우기 작업은 재구성될 수 없는 방식으로 정보를 삭제합니다. 활성화된 경우, BIOS는 다음 재부팅 시 마더보드에 연결된 스토리지 디바이스의 데이터 지우기 주기를 대기열에 넣습니다. 기본값: 해제 BIOS 다운그레이드 허용 시스템 펌웨어의 이전 버전으로의 플래시를 제어합니다. 기본값: 설정 표 17. 시스템 설치 옵션—시스템 로그 메뉴 시스템 로그 Power Event Log 전원 이벤트를 표시합니다. 기본값: 유지. BIOS 이벤트 로그 BIOS 이벤트를 표시합니다. 기본값: 유지. 열 이벤트 로그 열 이벤트를 표시합니다. 기본값: 유지. 표 18.
노트: 적절한 범주를 선택하여 제품 페이지에 연결합니다 5. 컴퓨터 모델을 선택하면 컴퓨터에 Product Support(제품 지원) 페이지가 표시됩니다. 6. Get drivers(드라이버 가져오기)를 클릭하고 Drivers and Downloads(드라이버 및 다운로드)를 클릭합니다. 드라이버 및 다운로드 섹션 표시됩니다. 7. Find it myself(직접 찾기)를 클릭합니다. 8. BIOS 버전을 보려면 BIOS를 클릭합니다. 9. 최신 BIOS 파일을 찾고 Download(다운로드)를 클릭합니다. 10. Please select your download method below(아래의 다운로드 방법을 선택하십시오) 창에서 원하는 다운로드 방법을 선택하고 Download File(파일 다운로드)을 클릭합니다. File Download(파일 다운로드) 창이 나타납니다. 11. 파일을 바탕 컴퓨터에 저장하려면 Save(저장)를 클릭합니다. 12.
그림 1 . DOS BIOS 업데이트 화면 Linux 및 Ubuntu 환경에서 Dell BIOS 업데이트 Ubuntu와 같은 Linux 환경에서 시스템 BIOS를 업데이트하려면 https://www.dell.com/support/article/sln171755/를 참조하십시오. F12 원타임 부팅 메뉴에서 BIOS 플래싱 FAT32 USB 드라이브에 복사된 BIOS update.exe 파일로 시스템 BIOS를 업데이트하고 F12 원타임 부팅 메뉴에서 부팅합니다. 이 작업 정보 BIOS 업데이트 부팅 가능한 USB 드라이브를 사용하여 Windows에서 BIOS 업데이트 파일을 실행하거나 컴퓨터의 F12 원타임 부팅 메뉴에서 BIOS를 업데이트할 수도 있습니다. 2012년 이후에 제작된 Dell 컴퓨터는 대부분 이 기능을 가지고 있으며, F12 원타임 부팅 메뉴로 컴퓨터를 부팅해서 BIOS 플래시 업데 이트가 컴퓨터의 부팅 옵션으로 등록되어 있는지 확인하는 방식으로 기능을 확인할 수 있습니다.
플래시 BIOS 메뉴가 표시됩니다. 3. 파일에서 플래시를 클릭합니다. 4. 외부 USB 디바이스를 선택하십시오. 5. 파일을 선택하고 플래시 타겟 파일을 두 번 클릭한 다음 제출을 클릭합니다. 6. BIOS 업데이트를 클릭합니다. 컴퓨터가 재시작되며 BIOS를 플래시합니다. 7. BIOS 업데이트가 완료된 후에 컴퓨터가 재시작됩니다. 시스템 및 설정 암호 표 19. 시스템 및 설정 암호 암호 유형 설명 시스템 암호 시스템에 로그인하기 위해 입력해야 하는 암호입니다. 설정 암호 컴퓨터의 BIOS 설정에 액세스하고 변경하기 위해 입력해야 하는 암호. 컴퓨터 보안을 위해 시스템 및 설정 암호를 생성할 수 있습니다. 주의: 암호 기능은 컴퓨터 데이터에 기본적인 수준의 보안을 제공합니다. 주의: 컴퓨터가 잠겨 있지 않고 사용하지 않는 경우에는 컴퓨터에 저장된 데이터에 아무나 액세스할 수 있습니다. 노트: 시스템 및 설정 암호 기능은 비활성화되어 있습니다.
이 작업 정보 시스템 설정에 들어가려면 전원이 켜진 직후 또는 재부팅 직후에 키를 누릅니다. 단계 1. System BIOS 또는 System Setup 화면에서 System Security를 선택하고 키를 누릅니다. System Security(시스템 보안) 화면이 표시됩니다. 2. System Security(시스템 보안) 화면에서 Password Status(암호 상태)를 Unlocked(잠금 해제)합니다. 3. System Password를 선택하고, 기존 시스템 암호를 업데이트하거나 삭제한 후 또는 키를 누릅니다. 4. Setup Password를 선택하고, 기존 설정 암호를 업데이트하거나 삭제한 후 또는 키를 누릅니다. 노트: 시스템 및/또는 설정 암호를 변경하는 경우 프롬프트가 나타나면 새 암호를 다시 입력합니다. 시스템 및/또는 설정 암 호를 삭제하는 경우 프롬프트가 나타나면 삭제를 확인합니다. 5.
5 문제 해결 운영 체제 복구 컴퓨터가 반복 시도 후에도 운영 체제로 부팅할 수 없는 경우, Dell SupportAssist OS 복구를 자동으로 시작합니다. Dell SupportAssist OS 복구는 Windows 10 운영 체제와 함께 설치되는 모든 Dell 컴퓨터에 사전 설치되어 있는 독립 실행형 툴입니다. 컴퓨터가 운영 체제로 부팅하기 전에 발생할 수 있는 문제를 진단하고 해결할 수 있는 툴로 구성됩니다. 이 툴을 통해 하드웨어 문제 를 진단하거나, 컴퓨터를 수리하거나, 파일을 백업하거나, 출하 시 상태로 컴퓨터를 복원할 수 있습니다. 소프트웨어 또는 하드웨어 장애로 인해 컴퓨터가 기본 운영 체제로 부팅할 수 없을 때 컴퓨터 문제를 해결하고 수정하기 위해 Dell Support 웹 사이트에서 이 툴을 다운로드할 수도 있습니다. Dell SupportAssist OS 복구에 대한 자세한 내용은 Dell SupportAssist OS 복구 사용자 가이드(www.dell.
표 20. LED 코드 (계속) 진단 표시등 코드 문제 설명 3,4 복구 이미지를 찾았지만 유효하지 않음 3,5 전원 레일 장애 3,6 시스템 BIOS 플래시 불완전 3,7 ME(Management Engine) 오류 카메라 상태 표시등: 카메라가 사용 중인지 여부를 나타냅니다. ● 솔리드 화이트 - 카메라가 사용 중입니다. ● 꺼짐 - 카메라가 사용 중이 아닙니다. Caps Lock 상태 표시등: Caps Lock가 활성화되어 있는지 또는 비활성화되어 있는지 여부를 나타냅니다. ● 솔리드 화이트 - 키가 활성화되어 있습니다. ● 꺼짐 - Caps Lock 비활성화 인텔 옵테인 메모리 활성화 단계 1. 작업 표시줄에서 검색 상자를 클릭한 후 인텔 빠른 스토리지 기술을 입력합니다. 2. 인텔 빠른 스토리지 기술를 클릭합니다. Intel Rapid Storage Technology(인텔 빠른 스토리지 기술) 창이 표시됩니다. 3.
잔류 전원 방출 이 작업 정보 잔류 전원은 전원을 끄고 배터리가 제거된 후에도 컴퓨터에 남아 있는 정전기입니다. 다음 절차는 잔류 전원을 방출하는 방법에 대한 지침을 제공합니다. 단계 1. 컴퓨터를 끕니다. 2. 베이스 커버를 제거합니다. 3. 배터리를 제거합니다. 4. 약 15초간 전원 버튼을 눌러 잔류 전원을 방전시킵니다. 5. 배터리를 장착합니다. 6. 베이스 커버를 장착합니다. 7. 컴퓨터를 켭니다. Wi-Fi 전원 주기 이 작업 정보 Wi-Fi 연결 문제로 인해 컴퓨터에서 인터넷에 액세스할 수 없는 경우 Wi-Fi 전원 주기 절차를 수행할 수 있습니다. 다음 절차는 Wi-Fi 전원 주기를 수행하는 방법에 대한 지침을 제공합니다. 노트: 일부 ISP(Internet Service Providers)는 모뎀/라우터 콤보 디바이스를 제공합니다. 단계 1. 컴퓨터를 끕니다. 2. 모뎀을 끕니다. 3. 무선 라우터를 끕니다. 4. 약 30초간 기다립니다. 5. 무선 라우터를 켭니다. 6.
6 도움말 보기 및 Dell에 문의하기 자체 도움말 리소스 다음과 같은 자체 도움말 리소스를 이용해 Dell 제품 및 서비스에 관한 정보 및 도움말을 얻을 수 있습니다. 표 21. 자체 도움말 리소스 자체 도움말 리소스 리소스 위치 Dell 제품 및 서비스 정보 www.dell.com My Dell 추가 정보 지원 문의 Windows 검색에서 Contact Support를 입력한 다음 키를 누릅니다. 운영 체제에 대한 온라인 도움말 www.dell.com/support/windows www.dell.com/support/linux 문제 해결 정보, 사용자 설명서, 설치 지침서, 제품 사양, 기술 지 원 블로그, 드라이버, 소프트웨어 업데이트 등 www.dell.com/support 다양한 컴퓨터 우려 사항에 대한 Dell 기술 자료 1. www.dell.com/support로 이동합니다. 2. 지원 페이지 상단의 메뉴 표시줄에서 지원 > 기술 자료를 선 택합니다.