Network Card User Manual
Table Of Contents
- Dell PowerEdge RAID Controller (PERC) H310, H710, H710P, and H810 User’s Guide
- Overview
- Features
- Physical Disk Power Management
- Types Of Virtual Disk Initialization
- Consistency Checks
- Disk Roaming
- FastPath
- Virtual Disk Migration
- Virtual Disk Write Cache Policies
- Virtual Disk Read Cache Policies
- Reconfiguration Of Virtual Disks
- Fault Tolerance
- The SMART Feature
- Patrol Read
- Redundant Path Support (For PERC H810 Only)
- Physical Disk Failure Detection
- Using Persistent Hot Spare Slots
- Physical Disk Hot Swapping
- Using Replace Member And Revertible Hot Spares
- Controller Cache Preservation
- Battery Transparent Learn Cycle
- Deploying The PERC Card
- Driver Installation
- Pre-Installation Requirements For Windows Driver Installation
- Creating The Device Driver Media For Windows Driver Installation
- Downloading Drivers From The Dell Systems Service And Diagnostic Tools Media For Windows
- Downloading Drivers From The Dell Support Website For Windows
- Installing Driver During a Windows Server 2008/2008 R2 Installation
- Installing Windows Server 2008/2008 R2 For A New RAID Controller
- Updating Existing Windows Server 2008 Or Windows Server 2008 R2
- Updating The Linux Driver
- Management Applications For PERC Cards
- Dell OpenManage Storage Management
- BIOS Configuration Utility
- Virtual Disk Management
- Creating Virtual Disks
- Selecting Virtual Disk Parameters
- Converting Physical Disk To RAID Capable For PERC H310
- Converting Physical Disk To Non-RAID For PERC H310
- Initializing Virtual Disks
- Checking Data Consistency
- Running A Data Consistency Check
- Importing Or Clearing Foreign Configurations Using The VD Mgmt Menu
- Importing Or Clearing Foreign Configurations Using The Foreign Configuration View Screen
- Break Mirror
- Managing Preserved Cache
- Managing Dedicated Hot Spares
- Deleting Virtual Disks
- Deleting Disk Groups
- Clearing The Configuration
- BIOS Configuration Utility Menu Options
- Physical Disk Management
- Controller Management
- UEFI RAID Configuration Utility
- CacheCade
- Security Key And RAID Management
- Troubleshooting
- BIOS Error Messages
- Discovery Error Message
- Extra Enclosure Error Message
- Cache Data Lost Error Message
- Missing Disks In Virtual Disk Error Message
- Previous Configuration Of Disks Removed Error Message
- Missing Virtual Disks Error Message
- Dirty Cache Data Error Message
- BIOS Disabled Error Message
- Drive Configuration Changes Error Message
- Adapter At Baseport Not Responding Error Message
- Offline Or Missing Virtual Drives With Preserved Cache Error Message
- Virtual Disks Offline Error Message
- Virtual Disks Degraded Error Message
- Virtual Disks Partially Degraded Error Message
- Memory Or Battery Problem Error Message
- Firmware Fault State Error Message
- Foreign Configuration Found Error Message
- Foreign Configuration Not Found In
Error Message - Previous Configuration Cleared Or Missing Error Message
- Invalid SAS Topology Detected Error Message
- Multibit ECC Errors Detected Error Messages
- Configured Disks Removed Or Not Accessible Error Message
- Battery Discharged Or Disconnected Error Message
- Degraded State Of Virtual Disks
- Memory Errors
- Preserved Cache State
- General Issues
- Physical Disk Issues
- Physical Disk In Failed State
- Unable to Rebuild A Fault Tolerant Virtual Disk
- Fatal Error Or Data Corruption Reported
- Physical Disk Displayed As Blocked
- Multiple Disks Become Inaccessible
- Rebuilding A Failed Physical Disk
- Virtual Disk Fails During Rebuild Using A Global Hot Spare
- Virtual Disk Fails During Rebuild Using A Dedicated Hot Spare
- Physical Disk Fails During Reconstruction On Redundant Virtual Disk
- Virtual Disk Fails Rebuild Using A Dedicated Hot Spare
- Physical Disk Takes A Long Time To Rebuild
- SMART Errors
- Replace Member Errors
- Linux Operating System Errors
- Disk Carrier LED Indicators
- BIOS Error Messages
- Appendix: RAID Description
![](/manual/dell/h710/network-card-user-manual/images/img-33.png)
The Consistency Check runs and checks the redundancy data in the virtual disks.
7. After you start the Consistency Check, press <Esc> to display the previous menu if needed.
Importing Or Clearing Foreign Configurations Using The VD Mgmt Menu
When a foreign configuration exists, the BIOS screen displays the message Foreign configuration(s)
found on adapter. In addition, a foreign configuration is displayed on the right side of the Ctrl Mgmt screen.
You can use the VD Mgmt menu to import the existing configuration to the RAID controller or clear the existing
configuration. In addition, you can view the foreign configuration from the Foreign View tab without importing the
configuration.
NOTE: The controller does not allow an import of configurations that results in more than 64 virtual disks.
NOTE: To import a secured foreign configuration, see the topic Security Key And RAID Management.
Perform the following steps to import or clear foreign configurations:
1. During bootup, press <Ctrl> <R> when prompted by the BIOS screen.
The VD Mgmt screen is displayed by default.
2. On the VD Mgmt screen, highlight the Controller #.
3. Press <F2> to display the available actions.
4. Navigate to the Foreign Config option and press the right arrow key to display the available actions: Import and
Clear.
NOTE: Ensure that your virtual disk has all the physical disks by verifying that there are no physical disks
marked as Missing in the foreign view page and that all the disks appear as expected before importing them.
5. Select Import to import the foreign configuration or Clear to delete the foreign configuration and then press
<Enter>.
If you import the configuration, the VD Mgmt screen displays detailed configuration information. It includes
information about the disk groups, virtual disks, physical disks, space allocation, and hot spares.
Importing Or Clearing Foreign Configurations Using The Foreign Configuration View
Screen
NOTE: To import a secured foreign configuration, see the topic Security Key And RAID Management.
If one or more physical disks are removed from a configuration, the configuration on those disks is considered a foreign
configuration by the RAID controller.
You can use the Foreign Configuration View screen to view information about the foreign configuration, such as disk
groups, virtual disks, physical disks, space allocation, and hot spares. The foreign configuration data is displayed in the
same format as configurations on the VD Mgmt screen. You can use the VD Mgmt screen to view the foreign
configuration before importing. After you view the foreign configuration, you can either clear or import to the RAID
controller.
NOTE: Before you import the foreign configuration, review the configuration on the screen to ensure that it is the
end result that you require.
You can use the Foreign Configuration View screen to manage foreign configurations in the following cases:
• All the physical disks in a configuration are removed and re-inserted.
• Some of the physical disks in a configuration are removed and re-inserted.
• All the physical disks in a virtual disk are removed, but at different times, and then re-inserted.
44