Integrated Dell Remote Access Controller 8 (iDRAC8) Version 2.00.00.
Notes, Cautions, and Warnings NOTE: A NOTE indicates important information that helps you make better use of your computer. CAUTION: A CAUTION indicates either potential damage to hardware or loss of data and tells you how to avoid the problem. WARNING: A WARNING indicates a potential for property damage, personal injury, or death. Copyright © 2014 Dell Inc. All rights reserved. This product is protected by U.S. and international copyright and intellectual property laws.
Contents 1 Introduction............................................................................. 11 New in This Release..........................................................................................11 Supported RACADM Interfaces....................................................................... 12 RACADM Syntax Usage.................................................................................... 13 SSH, Telnet, or Local RACADM...........................................................
eventfilters........................................................................................................39 fcstatistics.........................................................................................................41 frontpanelerror................................................................................................ 42 fwupdate.......................................................................................................... 42 get.....................................
serveraction......................................................................................................97 set.....................................................................................................................98 setled.............................................................................................................. 101 setniccfg......................................................................................................... 101 sshpkauth.......................
cfgStaticLanNetworking................................................................................ 154 cfgRemoteHosts............................................................................................ 157 cfgUserAdmin................................................................................................ 160 cfgEmailAlert.................................................................................................. 167 cfgSessionManagement.............................................
cfgRacSecurity...............................................................................................248 4 Database Objects With Get and Set Commands............251 System.Backplane..........................................................................................252 System.ChassisInfo........................................................................................253 System.QuickSync.........................................................................................254 System.
iDRAC.NICStatic.............................................................................................374 iDRAC.NTPConfigGroup............................................................................... 375 iDRAC.OS-BMC............................................................................................. 378 iDRAC.Racadm.............................................................................................. 380 iDRAC.RemoteHosts..........................................................
BIOS.MiscSettings..........................................................................................461 BIOS.NetworkSettings...................................................................................466 BIOS.OneTimeBoot.......................................................................................466 BIOS.ProcSettings......................................................................................... 469 BIOS.ProxyAttributes........................................................
Storage.enclosure......................................................................................... 645 Storage.PhysicalDisk..................................................................................... 647 Storage.VirtualDisk........................................................................................ 649 A Deprecated and New Subcommands.............................. 653 B Legacy and New Groups and Objects..............................655 cfgSSADRoleGroupPrivilege (Read or Write).
Introduction 1 This document provides information about the RACADM subcommands, supported RACADM interfaces, and property database groups and object definitions for the following: • iDRAC for Blade Servers • iDRAC on Rack and Tower Servers Most of the commands mentioned in this document are applicable for multigeneration servers. That is, the commands are applicable for iDRAC6, iDRAC7, and iDRAC8.
• Support to erase the components by using the systemerase subcommand to remove the server from use. • Support to generate technical support report operations using the techsupreport subcommand. • Support to view the host network interface details using the gethostnetworkinterfaces subcommand. • Support to view the system performance monitoring operations using the systemperfstatistics subcommand.
Controller (RAC). The utility runs on the management station and the managed system. It is available on the Dell OpenManage Systems Management and Documentation DVD or at support.dell.com. The RACADM utility supports the following interfaces: • Local — Supports running RACADM commands from the managed server’s operating system. To run local RACADM commands, install the OpenManage software on the managed server. Only one instance of Local RACADM can be executed on a system at a time.
Example racadm get idrac.info racadm getsysinfo Remote RACADM racadm -r -u -p get ..[].[] racadm -r -u -p set ..[]. racadm -r -u -p Example racadm -r 192.168.1.0 -u root -p xxxx get idrac.ssh.
Example racadm get nic.nicconfig.2 [Key=NIC.Integrated.1-2-1#nicconfig] BannerMessageTimeout=5 BootStrapType=AutoDetect HideSetupPrompt=Disabled LegacyBootProto=NONE LnkSpeed=AutoNeg #VLanId=1 VLanMode=Disabled • To display a single object for the specified group, run: racadm get device...
Option Description error message if it detects an invalid certificate. --nocertwarn Does not display certificate related warning message. NOTE: Up to four instances of remote RACADM can be executed on a management station, while only one instance of local RACADM can be executed on a managed node. Using The Autocomplete Feature Use the autocomplete feature to: • Display all the available RACADM commands in the alphabetical order on pressing the key at the prompt.
. . . . vflashsd vflashpartition vmdisconnect cd quit • Example 2: racadm> get get getconfig getled getniccfg getraclog getractime getsel getsensorinfo getssninfo getsvctag getsysinfo gettracelog getversion • Example 3: racadm> getl racadm> getled or LEDState: Not-Blinking Supported RACADM Subcommands The following table provides the list of RACADM subcommands and their corresponding interface support.
Subcommand iDRAC on Blade Servers iDRAC on Rack and Tower Servers Telnet/S Loca Rem Telnet/ SH/Serial l ote SSH/ RAC RACA Serial ADM DM Local Rem RACA ote DM RAC ADM clearasrscreen Yes Yes Yes Yes Yes Yes clearpending Yes Yes Yes Yes Yes Yes closessn Yes Yes Yes Yes Yes Yes clrsel Yes Yes Yes Yes Yes Yes config Yes Yes Yes Yes Yes Yes coredump Yes Yes Yes Yes Yes Yes coredumpdelete Yes Yes Yes Yes Yes Yes diagnostics Yes Yes Yes Yes Yes Yes eventfil
Subcommand iDRAC on Blade Servers iDRAC on Rack and Tower Servers Telnet/S Loca Rem Telnet/ SH/Serial l ote SSH/ RAC RACA Serial ADM DM Local Rem RACA ote DM RAC ADM gettracelog Yes Yes Yes Yes Yes Yes getversion Yes Yes Yes Yes Yes Yes help and help subcommand Yes Yes Yes Yes Yes Yes hwinventory Yes Yes Yes Yes Yes Yes ifconfig Yes Yes Yes Yes Yes Yes inlettemphistory Yes Yes Yes Yes Yes Yes jobqueue Yes Yes Yes Yes Yes Yes krbkeytabupload No Yes Yes
Subcommand iDRAC on Blade Servers iDRAC on Rack and Tower Servers Telnet/S Loca Rem Telnet/ SH/Serial l ote SSH/ RAC RACA Serial ADM DM Local Rem RACA ote DM RAC ADM sshpkauth Yes Yes Yes Yes Yes Yes sslcertupload No Yes Yes No Yes Yes sslcertview Yes Yes Yes Yes Yes Yes sslcertdelete Yes Yes Yes Yes Yes Yes sslcsrgen Yes Yes Yes Yes Yes Yes sslkeyupload No Yes Yes No Yes Yes sslresetcfg Yes Yes Yes Yes Yes Yes storage Yes Yes Yes Yes Yes Yes swinve
Other Documents You May Need In addition to this guide, you can access the following guides available on the Dell Support website at www.dell.com/esmmanuals. To access the documents, click the appropriate product link. • The Integrated Dell Remote Access Controller 8 (iDRAC8) User’s Guide provides information about configuring and using an iDRAC to remotely manage and monitor your system and its shared resources through a network.
Accessing documents from Dell support site You can access the required documents in one of the following ways: • Using the following links: – For all Systems Management documents — dell.com/ softwaresecuritymanuals – For Remote Enterprise Systems Management documents — dell.com/ esmmanuals – For Enterprise Systems Management documents — dell.com/ openmanagemanuals – For Client Systems Management documents — dell.com/ clientsystemsmanagement – For Serviceability Tools documents — dell.
Contacting Dell NOTE: If you do not have an active Internet connection, you can find contact information on your purchase invoice, packing slip, bill, or Dell product catalog. Dell provides several online and telephone-based support and service options. Availability varies by country and product, and some services may not be available in your area. To contact Dell for sales, technical support, or customer service issues: 1. Go to dell.com/support. 2. Select your support category. 3.
2 RACADM Subcommand Details This section provides detailed description of the RACADM subcommands including the syntax and valid entries.
There are different escaping rules for using single quotation marks versus double quotation marks. For using double quotation marks: The following characters must be escaped by prepending a backslash: • $ (dollar sign) • " (double quote) • ` (back quote) • \ (back slash) For example, use the following for a string that contains the special characters, $, ",',`and \ For using single quotation marks: • No character escaping is necessary.
Output •
autoupdatescheduler Descriptio You can automatically update the firmware of the devices on n the server. To run this subcommand, you must have the Server Control privilege. NOTE: • • • • • • Synopsis The autoupdatescheduler subcommand can be enabled or disabled. Lifecycle Controller and CSIOR may not be enabled to run this subcommand. The autoupdatescheduler can be enabled or disabled. For more information, see LifecycleController.LCAttributes.
Input Valid options: • • • • • • • • • • • • • • 28 -u — Specifies the user name of the remote share that stores the catalog file. NOTE: For CIFS, enter the domain name as domain or username. -p — Specifies the password of the remote share that stores the catalog file. -l — Specifies the network share (NFS, CIFS, FTP, TFTP, or HTTP) location of the catalog file. IPv4 and IPv6 addresses are supported. -f — Specifies the catalog location and the filename.
NOTE: The -dom, -wom, or -dow option must be included in the command for the autoupdate schedule. The * value for the options must be included within ' ' (single quotation mark). • • • • • • • • Example If the -dom option is specified, then the -wom and -dow options are not required. If the-wom option is specified, then the-dow is required and -dom is not required. If the-dom option is non-'*', then the schedule repeats by month. If the-wom option is non-'*', then the schedule repeats by month.
cat.xml.gz -ph 10.20.30.40 -pu padmin -pp ppwd -po 8080 -pt http -time 14:30 -dom 1 rp 5 -a 1 – For HTTP, run the command: racadm autoupdatescheduler create -u httpuser -p httppwd -l http://test.com f cat.xml -ph 10.20.30.40 -pu padmin -pp ppwd -po 8080 -pt http -time 14:30 -dom 1 -rp 5 -a 1 – For TFTP, run the command: racadm autoupdatescheduler create -l tftp://1.2.3.4 -f cat.xml.gz -time 14:30 dom 1 -rp 5 -a 1 – To view AutoUpdateScheduler parameter: racadm autoupdatescheduler view hostname = 192.168.1.
• Example 2: To run all the power-related get or setcommands: racadm/system>cd power racadm/Power> cd.. Descripti on To go back to the previous directory, use this command. Synopsis racadm> cd.. Input racadm> cd.. Output To traverse back to the previous directory, use the command. Example • Example 1: To traverse back from power to system object: – Input: racadm/power> cd.. – Output: system>> • Example 2: To traverse back from system object to the prompt: – Input:racadm/system> cd..
Output Clears the last crash screen buffer. Example racadm clearasrscreen clearpending Descriptio Deletes the pending values of all the attributes (objects) in the n device (NIC, BIOS, FC, and Storage). NOTE: If any attribute is not modified or a job is already scheduled for the same device, then the pending state is not cleared or deleted.
Input • • • —i — The session ID of the session to close, which can be retrieved using RACADM getssninfo subcommand. Session running this command cannot be closed. —a — Closes all sessions. —u — Close all sessions for a particular username. —u option can be used in local RACADM only if the username contains up to 16 characters. If the user name contains more than 16 characters, use -i option. Output Successful or error message is displayed. Example • Closes the session 1234.
Clear SEL log on server 1: racadm clrsel -m server-1 config Descripti on Allows you to set iDRAC configuration parameters individually or to batch them as part of a configuration file and then modify CMC configuration properties. If the data is different, the iDRAC object is written with a new value. NOTE: This subcommand will be deprecated in the later versions. For information about configurations, see set subcommand.
• -p — This option must be used with the -f option. It directs config to delete the password entries contained in the config file -f after the configuration is complete. To apply the password, you must remove the preceding Read-Only marker '#' in the config file before executing the config -f command. • -g — The -g , or group option, must be used with the -o option. The specifies the group containing the object that is to be set.
NOTE: The myrac.cfg file does not contain passwords. To include passwords in the file, you must enter them manually. If you want to remove password information from the myrac.cfg file during configuration, use the -p option. coredump Description Displays detailed information related to any recent critical issues that have occurred with iDRAC. The coredump information can be used to diagnose these critical issues.
To use this subcommand, you must have Execute Debug Command permission. NOTE: If a coredumpdelete command is issued and a coredump is not currently stored in the RAC, the command displays a success message. This behavior is expected. See the coredump subcommand for more information about viewing a coredump. Synopsis racadm coredumpdelete Output Coredump is deleted.
• • • • • • • – 1(Extended) — The extended mode executes all available diagnostics tests. – 2(Both) — Runs express and extended tests serially in sequence. -f — Specifies the name of the configuration file. -l — Specifies the location of the network share (NFS or CIFS). -u — Specifies the user name of the remote share to import the file. -p — Specifies the password of the remote share to import the file. -r — Specifies the reboot type.
eventfilters Descripti on Displays the list of event filter settings. Synopsis racadm eventfilters To use this subcommand with the set and test option, you must have the Administrator privilege.
Input • • idrac.alert.audit.warning idrac.alert.audit.lic.critical • • get — Displays the list of eventfilter settings. set — Configures the actions and notifications for a given eventfilter configuration. -i — Message ID for which the simulation is needed. -c — Alert category of the specific event filter. -a — The action that must be invoked when the event occurs. Valid values are none, powercycle, power off, or systemreset. -n — The notification is sent when the event occurs.
• Display eventfilter configurations for a specific severity and subcategory. For example, a severity of warning in the subcategory licensing under audit category: racadm eventfilters get -c idrac.alert.audit.lic.warning • Clear all available alert settings: racadm eventfilters set -c idrac.alert.all -a none -n none • Configure using severity as a parameter.
Input — Specify the FQDD of the target FC device. Example racadm fcstatistics frontpanelerror Descripti on Enables or disables the live-feed of the errors currently being displayed on the LCD screen. For error acknowledge use hide, and error assert use show. Synopsis racadm frontpanelerror show racadm frontpanelerror hide Input • • Example show — to view the errors currently being displayed on the LCD screen.
To use this subcommand, you must have Configure iDRAC permission. Synopsis racadm fwupdate -s racadm fwupdate -g -u -a [-d [--clearcfg] racadm -r -u -p fwupdate -f -d where path is the location on the ftp server where firmimg.d7 is stored.
• • -f— Specifies the FTP server IP address or FQDN, username, and password used for firmware image. Applies FTP download process for firmware update. --clearcfg (Optional) — After the firmware update, this option removes the previous iDRAC configuration. CMC version 3.00 accepts IPv4, IPv6 or fully qualified domain names (FQDN) for both FTP and TFTP servers. Output Displays a message indicating the operation that is being performed. Example • Update firmware on servers of iDRAC generation.
FW Update Method iDRAC on Blade Servers iDRAC on Rack and Tower Servers Local RACADM Yes Yes Local RACADM-TFTP Yes Yes Local RACADM-FTP Yes Yes Remote RACADM Yes Yes Remote RACADMTFTP Yes Yes Remote RACADMFTP Yes Yes Firmware RACADMTFTP Yes Yes Firmware RACADMFTP Yes Yes get Descripti on Displays the object and its values. If the values are pending, then commit and reboot job must be created using the jobqueue command. For more information, see jobqueue.
To run this subcommand for configuration xml file type, the Lifecycle Contoller version 1.1 or later is required. Synopsis racadm get -f racadm get ....
• • • • • • • • • • •
• Export the xml configuration to a CIFS share. racadm get -f file -t xml -u myuser -p mypass -l //10.1.12.13/share • Export the xml configuration to an NFS share. racadm get -f file -t xml -l 10.1.12.13:/ myshare • racadm get -f xyz_temp_clone -t xml -u Administrator -p dell_123 -l //10.94.162.74/ xyz --clone • racadm get -f xyz_temp_replace -t xml -u Administrator -p dell_123 -l //10.94.162.74/ xyz --replace • Export the xml configuration of the iDRAC component to a CIFS share.
• • • • • • Output NOTE: This option is supported only on remote interfaces. -g — The -g or group option, is used to display the configuration for a single group. The is the name for the group used in the racadm.cfg files. If the group is an indexed group, then use the-i option. -h — The -h or help option, displays a list of all available configuration groups in alphabetical order. This option is useful when you do not remember exact group names.
• Displays the configuration properties for the user named root. racadm getconfig -u root • Displays the user group instance at index 2 with verbose information for the property values. racadm getconfig -g cfgUserAdmin -i 2 -v • Displays an entire group of serial configuration. racadm getconfig -g cfgSerial • Displays a single object from a particular group. racadm getconfig -g cfgSerial -o cfgSerialBaudRate • Displays an indexed group.
IPv6 Address : fe80::1cce:a0a7:f30e:54fc Prefix Length : IPv6 DNSServer Address 0: IPv6 DNSServer Address 1: IPv6 DNSServer Address 2: • 64 fec0:0:0:ffff::1 fec0:0:0:ffff::2 fec0:0:0:ffff::3 To display the details of a particular NIC on the server. racadm gethostnetworkinterfaces NIC.Integrated.
Example racadm getled LED State : Blinking racadm getled LED State : Not-Blinking getniccfg Descripti on Displays the current and static NIC settings for iDRAC. Synopsis racadm getniccfg Input racadm getniccfg Example racadm getniccfg Output The getniccfg subcommand displays an appropriate error message if the operation is not successful.
IPv6 settings: IPv6 Enabled = 0 DHCP6 Enabled = 1 IP Address 1 = :: Gateway = :: Link Local Address = :: IP Address 2 = :: IP Address 3 = :: IP Address 4 = :: IP Address 5 = :: IP Address 6 = :: IP Address 7 = :: IP Address 8 = :: IP Address 9 = :: IP Address 10 = :: IP Address 11 = :: IP Address 12 = :: IP Address 13 = :: IP Address 14 = :: IP Address 15 = :: LOM Status: NIC Selection = Dedicated Link Detected = Yes Speed = 10Mb/s Duplex Mode = Half Duplex Active
NOTE: IPv6 information is displayed only if IPv6 is enabled in iDRAC. NOTE: LOM Status is displayed only for iDRAC on Rack and Tower servers and is not displayed for iDRAC Enterprise on Blade servers. getraclog Descripti on The getraclog command displays RAC log entries. Synopsis racadm getraclog -s -c NOTE: When this command is run on Local RACADM, the data is available to RACADM as a USB partition and may display a pop-up message.
SeqNumber = 4102 Message ID = LIC201 Category = Audit AgentID = DE Severity = Warning Timestamp = 2014-06-12 01:38:19 Message = License yPMRJGuEf7z5HG8LO7gh assigned to device iDRAC expires in 4 days.
getsel Descripti on Displays all sensor event log entries in the DRAC. Synopsis • • racadm getsel -i [-A] racadm getsel [-s][-c] [-A] [-o] [-E] [-R] [--more] NOTE: If no arguments are specified, the entire log is displayed. Input • • • • —c — Displays the number of records. —s — Specifies the starting record used for the display. —i — Displays the number of entries in the SEL. --more — Displays one screen at a time and prompts the user to continue (similar to the UNIX more command.
Examples: racadm getsensorinfo Sensor Type : POWER PS1 Status Present AC Sensor Type : TEMPERATURE ng> [R/ W] [R/W] System Board Inlet Temp Ok 20 C -7 C 47 C 3 C [Y] 42C [Y] System Board Exhaust Temp Ok 19 C 0 C 75 C 0 C [N] 70 C [N] CPU1 Temp Ok 59 C 3 C 97 C 8 C [N] 92 C [N] Sensor Type : FAN System Board Fan1 RPM Ok 2280 RPM 360 RPM NA System
System Board Fan5 RPM Ok 2280 RPM 360 RPM NA System Board Fan6 RPM Ok 2280 RPM 360 RPM NA Sensor Type : VOLTAGE CPU1 VCORE PG Ok Good NA NA System Board 3.3V PG Ok Good NA NA System Board 5V AUX PG Ok Good NA NA CPU1 M23 VPP PG Ok Good NA NA System Board 1.
System Board 2.5V AUX PG Ok Good NA NA CPU1 M01 VDDQ PG Ok Good NA NA System Board NDC PG Ok Good NA NA CPU1 M01 VPP PG Ok Good NA NA System Board 1.5V PG Ok Good NA NA System Board PS2 PG Fail Ok Good NA NA System Board PS1 PG Fail Ok Good NA NA System Board 1.
> [R/W] [R/W] PS1 Ok Current 1 0.
System Board Power Optimized Ok Not Degraded NA NA Sensor Type : INTRUSION System Board Intrusion Closed Power ON Sensor Type : REDUNDANCY System Board Fan Redundancy Full Redundant Fan System Board PS Redundancy Disabled PSU Sensor Type : SYSTEM PERFORMANCE > [R/W] [R/W] System Board CPU Usage Non0% Critica l 0% 10
System Board SYS Usage Non0% Critica l 0% 100% 0% [N] 99% [Y] getssninfo Description Displays a list of users that are connected to iDRAC. The following information is displayed: • Session ID • Username • IP address (if applicable) • Session type (for example, serial or Telnet) • Login date and time in MM/DD/YYYY HH:MM:SS format NOTE: Based on the Session ID (SSNID) or the user name (User), the iDRAC administrator can close the respective sessions or all the sessions using the closessn subcommand.
getsvctag Description Displays the service tag of the host system. Synopsis racadm getsvctag Output Any system tag as applicable. Example Display Service tag of Server in Slot 1 racadm getsvctag -m server-1 racadm getsvctag Y76TP0G getsysinfo Descripti on Displays information related to iDRAC, managed system, and watchdog configuration.
Output racadm getsysinfo RAC Information: RAC Date/Time Firmware Version Firmware Build Last Firmware Update Hardware Version MAC Address = = = = = = Common settings: Register DNS RAC Name DNS RAC Name Current DNS Domain Domain Name from DHCP = 0 = idrac-H1VGF2S = = Disabled IPv4 settings: Enabled Current IP Address Current IP Gateway Current IP Netmask DHCP Enabled Current DNS Server 1 Current DNS Server 2 DNS Servers from DHCP = = = = = = = = 1 192.168.0.1 192.168.0.1 192.168.0.1 1 0.0.0.0 0.0.0.
Current DNS Server 1 Current DNS Server 2 = :: = :: System Information: System Model System Revision System BIOS Version Service Tag Express Svc Code Host Name OS Name OS Version Power Status Fresh Air Capable = = = = = = = = = = PowerEdge R520 I 1.5.0 H1VGF2S 37118600020 ON Yes Watchdog Information: Recovery Action = None Present countdown value = 15 seconds Initial countdown value = 15 seconds Embedded NIC MAC Addresses: NIC.Embedded.1-1-1 Ethernet 11:3C:B5 WWN 11:3C:B5 NIC.Embedded.
• racadm getsysinfo -w -s System Information: System Model System Revision System BIOS Version Service Tag Express Svc Code Host Name OS Name OS Version Power Status Fresh Air Capable = = = = = = = = = = PowerEdge R520 I 1.5.0 H1VGF2S 37118600020 ON Yes Watchdog Information: Recovery Action = None Present countdown value = 15 seconds Initial countdown value = 15 seconds Embedded NIC MAC Addresses: NIC.Embedded.1-1-1 Ethernet 90:B1:1C:11:3C:B5 WWN 90:B1:1C:11:3C:B5 NIC.Embedded.
Output The default output display shows the record number, timestamp, source and description. The timestamp begins at midnight, January 1 and increases until the system starts. After the system starts, the system’s timestamp is used. Example Display entire log: racadm gettracelog Display number of records in log: racadm gettracelog -i Record: 1 Date/Time: Dec Source: ssnmgrd[175] 8 08:21:30 Description: root from 143.166.157.
• racadm getversion -f idrac racadm getversion -c server-1 1.0.5 PowerEdgeM520 server-2 1.0.3 PowerEdgeM610x server-4 1.0.0 PowerEdgeM710HD server-5 1.0.3 PowerEdgeM710 server-7 1.0.6 PowerEdgeM620 server-9 1.0.5 PowerEdgeM520 racadm getversion Bios Version = 2.0.18 iDRAC Version = 2.00.00.00 Lifecycle Controller Version = 2.00.00.00 racadm getversion -b server-1 1.6.0 PowerEdgeM520 server-2 6.3.
switch-2 M8024-k 10GbE SW A00 switch-3 Dell PowerConnect M8024 X00 switch-4 Dell PowerConnect M8024 X00 switch-5 Dell PowerConnect M6348 X02 switch-6 Dell PowerConnect M6220 A01 5.0.1.3 hwinventory Description Allows you to display or export current internal hardware inventory or shipped hardware inventory by device.
Examples To get the list of NIC FQDDs racadm hwinventory nic NIC.Slot.2-1-1:Emulex OCe14102-U1-D - 00:90:FA:4C:FE:C2 PartitionCapable : 1 NIC.Slot.2-1-2:Emulex OCe14102-U1-D - 00:90:FA:4C:FE:C3 PartitionCapable : 2 NIC.Slot.2-1-3:Emulex OCe14102-U1-D - 00:90:FA:4C:FE:C4 PartitionCapable : 3 NIC.Slot.2-1-4:Emulex OCe14102-U1-D - 00:90:FA:4C:FE:C5 PartitionCapable : 4 To get the complete details for NIC.Integrated.1-4-1: racadm hwinventory NIC.Integrated.
VirtWWPN: Family Version: Controller BIOS Version: EFI Version: Max Bandwidth: Min Bandwidth: FCoE WWNN: Vendor Name: Number of PCI-e Functions Supported per Port: Number of PCI-e Functions Currently Enabled per Port: Family Driver Version : Protocol: Link Duplex: Applicable Link Speed: Applicable Auto Negotiated: Transmit Flow Control: Receive Flow Control: Media Type: NIC Mode: FCoE Offload Mode: iSCSI Offload Mode: Max Number of IOs per session supported: Number of Max LOGINs per port: Max Number of exch
Enhanced Transmission Selection: Priority Flow Control: DCB Exchange Protocol: Congestion Notification: VEB-VEPA Single Channel: VEB-VEPA Multi Channel: EVB: BPE: Open Flow: Partition WOL Support: Virtual Link Control Partition RX Flow Control: Partition TX Flow Control: TX Bandwidth Control Maximum: TX Bandwidth Control Minimum: Not Not Not Not Not Not Not Not Not Not Not Not Not Not Not Capable Capable Capable Capable Capable Capable Capable Capable Capable Capable Capable Capable Capable Capable Capabl
21:00:00:24:FF:08:9D:8A VirtWWPN: 21:00:00:24:FF:08:9D:8A Chip Type: Family Version: EFI Version: OS Driver Version: First FC Target WWPN: 50:06:01:60:44:60:28:8C First FC Target LUN: Second FC Target WWPN: 00:00:00:00:00:00:00:00 Second FC Target LUN: Hard Zone Address: Hard Zone Enable: FC Tape Enable: Loop reset Delay: Frame Payload Size : Fabric Login Retry Count: Fabric Login Timeout: Port Login Retry Count: Port Login Timeout: Port Down Retry Count: Port Down Timeout: Link Down Timeout: Port Number: P
OS Driver Version: First FC Target WWPN: 00:00:00:00:00:00:00:00 First FC Target LUN: Second FC Target WWPN: 00:00:00:00:00:00:00:00 Second FC Target LUN: Hard Zone Address: Hard Zone Enable: FC Tape Enable: Loop reset Delay: Frame Payload Size : Fabric Login Retry Count: Fabric Login Timeout: Port Login Retry Count: Port Login Timeout: Port Down Retry Count: Port Down Timeout: Link Down Timeout: Port Number: Port Speed: Max Number of IOs per connection supported: Maximum number of Logins per port: Maximum
eth0 Link encap:Ethernet HWaddr 00:1D: 09:FF:DA:23 inet addr:10.35.155.136 Bcast: 10.35.155.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU: 1500 Metric:1 RX packets:2550665 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:272532097 (259.9 MiB) TX bytes:0 (0.0 B) inlettemphistory Descripti on Displays the average and the peak temperatures during the last hour, day, week, month, or year.
NOTE: From firmware RACADM, only export to a remote share is supported. The behavior of remote share is not defined when the path specified (-l) contains special characters. Example • Export the log to a remote CIFS share. racadm inlettemphistory export -f Mylog.xml u admin -p mypass -l //1.2.3.4/share -t xml • Export the log to local file system using Local RACADM. racadm inlettemphistory export -f Mylog.xml t xml • Export the log to management station using Remote RACADM. racadm -r 1.2.3.
jobqueue Description Enables you to view and delete a job or jobs in the current Job Queue. NOTE: To run this subcommand, you must have the Server control privilege. Synopsis racadm jobqueue view -i racadm jobqueue delete [-i][--all] where valid options are -i and --all.
• --realtime — Specifies the real time job. NOTE: – --realtime is applicable for storage configuration commands run on systems with PERC 9 cards with firmware version 9.1 and later. – -r option is not valid for real time configuration. Example • View jobs in the current job queue. racadm jobqueue view • View jobs in the Current job queue and display the specific job ID. racadm jobqueue view -i • Delete all possible jobs from the current job queue.
To run this subcommand, you must have the Server Control privilege. Synopsis racadm krbkeytabupload [-f ] is the name of the file including the path. Input -f — Specifies the filename of the keytab uploaded. If the file is not specified, the keytab file in the current directory is selected. Output When successful Kerberos Keytab successfully uploaded to the RAC message is displayed. If unsuccessful, appropriate error message is displayed. Example racadm krbkeytabupload -f c:\keyt
category> -q -n -r -e racadm lclog comment edit –q m racadm lclog export -f -u p -l racadm lclog export -f -u p -l --complete racadm lclog viewconfigresult -j racadm lclog worknote add -m Input • • • • 80 -i — Displays the number of records present in the active log.
• • • • • • • • • • • • -q — The sequence number from which the records must be displayed. Records older than this sequence number is displayed. NOTE: This parameter input is an integer. If an alphanumeric input is provided, then invalid subcommand syntax error is displayed. -n — Specifies the n number of records that must be displayed. On Local RACADM, if this parameter is not specified, by default 100 logs are retrieved. -r — Displays events that have occurred after this time.
characters. The text must be specified within double quotation mark. NOTE: HTML-specific characters may appear as escaped text. NOTE: For -m and —m options, you need test alert privilege. • • Example • Display the number of records present in the Lifecycle log. racadm lclog view -i • Display the iDRAC agent idrac records, under the storage category and storage physical disk drive subcategory, with severity set to warning.
• Add a worknote to the Lifecycle log. racadm lclog worknote add -m "This is a test worknote." • Export the Lifecycle log to a remote CIFS share. racadm lclog export -f Mylog.xml -u admin -p mypass -l //10.94.161.103/share • Export the complete Lifecycle log in gzip format to a remote CIFS share. racadm lclog export -f log.xml.gz -u admin -p mypass -l //10.94.161.103/share --complete • Export the Lifecycle log to a remote NFS share. racadm lclog export -f Mylog.xml -l 10.94.161.
Input • racadm license delete -c [-o] • racadm license replace -u -p -f -l -t [-o] • • • • • view — View license information. import — Installs a new license. export — Exports a license file. delete — Deletes a license from the system. replace — Replaces an older license with a given license file. -l — Network share location from where the license file must be imported.
License Type Entitlement ID Q3XJmvoxZdJVSuZemDehlcrd License Bound Expiration Applicable = PERPETUAL = = H1VGF2S = Not • Import a new license to a specific device in a known location. $racadm license import -f license.xml -l //shareip/ sharename -u -p -c idrac.embedded.1 • Import a license from a CIFS share to a device, in this case Embedded iDRAC. racadm license import -u admin -p passwd -f License.xml -l //192.168.2.140/licshare -c idrac.embedded.
• Export license to a CIFS share specifying the entitlement ID, in this case abcdxyz. racadm license export -u admin -p passwd -f License.xml -l //192.168.2.140/licshare -e abcdxyz • Export license to a CIFS share specifying the FQDD. While using the -c option and exporting a license from a device, more than one license file may be exported. Therefore if a filename is given, an index is appended to the end of the filename such asLicenseFile0.xml, LicenseFile1.xml.
• Displays the statistics for the integrated NIC. $ racadm nicstatistics NIC.Integrated.1-1 Total Bytes Received:0 • Total Bytes Transmitted: 0 Total Unicast Bytes Received: 0 Total Multicast Bytes Received: 0 Total Broadcast Bytes Received: 0 Total Unicast Bytes Transmitted: 0 Get the network statistics. $ racadm nicstatistics NIC.Slot.5-2-1 : QLogic CNA Gigabit Ethernet-B8:AC: 6F:B3:BF:10 NIC.Slot.5-2-1 : QLogic CNA Gigabit Ethernet-B8:AC: 6F:B3:BF:11 NIC.Slot.
percent packet lossround-trip min/avg/max = 4.121/4.121/4.121 ms ping6 Verifies if the destination IPv6 address is reachable from iDRAC or with the current routing-table contents. A destination IPv6 address is required. Based on the current routing-table contents, an ICMP echo packet is sent to the destination IPv6 address. Descriptio n To run this subcommand, you must have Debug privilege. Synopsis racadm ping6 Input — the IPv6 address of the remote endpoint to ping.
• Synopsis RAC Firmware Build Log racadm racdump Example =========================================================== ==================== General System/RAC Information =========================================================== ==================== RAC Information: RAC Date/Time = Thu Jul Firmware Version Firmware Build Last Firmware Update Hardware Version MAC Address = = = = = Common settings: Register DNS RAC Name DNS RAC Name Current DNS Domain Domain Name from DHCP = 0 = idrac = = Disabled IP
Current IP Address 8 Current IP Address 9 Current IP Address 10 Current IP Address 11 Current IP Address 12 Current IP Address 13 Current IP Address 14 Current IP Address 15 DNS Servers from DHCPv6 Current DNS Server 1 Current DNS Server 2 = = = = = = = = = = = :: :: :: :: :: :: :: :: Disabled :: :: System Information: System Model System Revision System BIOS Version Service Tag Express Svc Code Host Name OS Name OS Version Power Status Fresh Air Capable = = = = = = = = = = PowerEdge R720 I 2.0.
Hop Iface :: 1/128 :: 1/128 Flags Metric Ref U U fe80::1a03:73ff:fef7:b7ca/ 128 :: U 0 0 1 lo fe80::/64 U ff00::/8 U Kernel IP routing table Destination Gateway MSS Window irtt Iface 0.0.0.0 192.168.0.1 0 0 0 bond0 192.168.0.1 0.0.0.0 0 0 0 bond0 0 1 256 0 :: :: 256 0 256 0 1 lo 0 lo :: :: 0 eth1 0 eth1 Genmask Flags 0.0.0.0 UG 192.168.0.1 U Active Internet connections (w/o servers) Proto Recv-Q Send-Q Local Address Address State tcp 0 0 192.168.0.1:53986 192.168.0.
==================== PID USER VSZ 1 root 5236 2 root 0 3 root 0 6 root 0 7 root 0 8 root 0 9 root 0 153 root 0 155 root 0 157 root 0 166 root 0 16233 root 40916 16246 root 3824 16247 root 3828 26851 root 0 STAT S SW SW SW SW< SW SW< SW SW SW< SW S S R SW COMMAND {systemd} /sbin/init [kthreadd] [ksoftirqd/0] [watchdog/0] [khelper] [kdevtmpfs] [netns] [sync_supers] [bdi-default] [kblockd] [khubd] racadm racdump sh -c /bin/ps /bin/ps [kworker/u:3] ===========================================================
Input • -f — This option is used to force the reset. Output racadm racreset RAC reset operation initiated successfully. It may take up to a minute for the RAC to come online again. Example • iDRAC reset. racadm racreset racresetcfg Description Deletes your current iDRAC configuration and resets iDRAC to the factory default settings. After reset, the default name and password are root and calvin, respectively, and the IP address is 192.168.0.120.
message. You can perform a force reset using this option. • Example Reset the configuration on iDRAC. racadm racresetcfg The RAC configuration has initiated restoration to factory defaults. • Wait up to a minute for this process to complete before accessing the RAC again. Reset when vFlash Partition creation is in progress. racadm racresetcfg A vFlash SD card partition operation is in progress. Resetting the iDRAC may corrupt the vFlash SD card. To force racresetcfg, use the -f flag.
• -s — Display current status. NOTE: Use a forward slash (/) when providing the image location. If backward slash (\) is used, override the backward slash for the command to run successfully. For example: racadm remoteimage -c -u user -p password l /\/\10.94.192.100/\CommonShare/\diskette NOTE: The following options only apply to connect and deploy actions Example • • • -u — Username -p — Password -1 • Configure a Remote image. racadm remoteimage -c -u "user" -p "pass" l //shrloc/foo.
rollback Descriptio Allows you to roll back the firmware to an earlier version. n Synopsis racadm rollback NOTE: To get the list of available rollback versions and FQDDs, run the racadm swinventory command. Input : Specify the FQDD of the device for which the rollback is required. Example racadm rollback iDRAC.Embedded.1-1 RAC1056: Rollback operation initiated successfully. sensorsettings Descripti on Allows you to perform threshold settings of the sensor.
Examples To set the minimum noncritical threshold level for a power sensor type. racadm sensorsettings set iDRAC.Embedded. 1#SystemBoardCPUUsage -level Max 95 NOTE: The entered value must be lesser or higher than the sensor critical threshold limit. serveraction Descripti on Enables you to perform power management operations on the host system. To run this subcommand, you must have the Execute Server Control Commands permission.
Examples Get Power Status on iDRAC, racadm serveraction powerstatus Server Power Status: ON racadm serveraction powercycle Server power operation successful set Descripti on Modifies the value of configuration objects on a device. NOTE: • • Synopsis Input • racadm set -f [--continue] • racadm set ...
• • • • • • • • • • -f — Enables set to configure the device from a specified file. This option is not supported in the Firmware RACADM interface. --continue — This option is used with –f only. If configuration through file is unsuccessful for a group, then configuration continues with the next group in the file. If this option is not used, then configuration stops when it is unsuccessful for a particular group. After the unsuccessful group, the rest of the groups are not configured.
• NOTE: – This option does not restart the system. – The-b,-w options cannot be included with the -preview option. – A scheduled job or pending configuration should not be running while using the --preview option. -c — Specifies the FQDD or list of FQDDs separated by ',' of the components for which the configurations should be imported. If this option is not specified, configuration related to all the components are imported.
setled Descripti on Sets the state (blinking or not blinking) of the LED on the specified module. To run this subcommand, you must have the Configure iDRAC permission. Synopsis racadm setled -l Input • -l — Specifies the LED state. The values are: – 0 — No Blinking – 1 — Blinking Example • From iDRAC stop LED from blinking. racadm setled -l 0 RAC0908: System ID LED blink off. • From iDRAC start LED to blink. racadm setled -l 1 RAC0907: System ID LED blink on.
Input • • • • • Example -d — Enables DHCP for the NIC (default is DHCP disabled.) -d6 — Enables AutoConfig for the NIC. It is enabled by default. -s — Enables static IP settings. The IPv4 address, netmask, and gateway must be specified. Otherwise, the existing static settings are used. , , and must be typed as dot-separated strings. racadm setniccfg -s 192.168.0.120 255.255.255.0 192.168.0.1 -s6 — Enables static IPv6 settings.
• • Upload — This mode allows you to upload a key file or copy the key text to the command line. You cannot upload and copy a key at the same time. Local and Remote RACADM: racadm sshpkauth -i <2 to 16> -k <1 to 4> -f • Remote RACADM: racadm sshpkauth -i <2 to 16> -k <1 to 4> -t • Telnet/SSH/serial RACADM: racadm sshpkauth -i <2 to 16> -k <1 to 4> -t • View — This mode allows to view a user-specified key or all keys.
• Upload a valid key to iDRAC User 2 in the first key space using a file. $ racadm sshpkauth -i 2 -k 1 -f pkkey.key Key file successfully uploaded. • Get all keys for User 2 on iDRAC.
Output Returns 0 when successful and nonzero number when unsuccessful. Example Download server certificate: racadm -r 192.168.0.120 -u root -p calvin sslcertdownload -t 1 -f cert.txt Download Active Directory certificate: racadm -r 192.168.0.120 -u root -p calvin sslcertdownload -t 2 -f ad_cert.txt NOTE: This command is not supported in the firmware RACADM interface as it is not a file system.
CSR is generated on another server, then it is necessary to upload the private key with the certificate. Output The sslcertupload command returns 0 when successful and returns nonzero number when unsuccessful. Example • Uploading a server certificate. racadm -r 192.168.0.120 -u root -p calvin sslcertupload -t 1 -f cert.txt • Uploading a PKCS file without any passphrase. racadm sslcertupload –t 3 –f • Uploading a PKCS file with a passphrase.
Serial Number 01 Subject Information: Country Code (CC) US State (S) Texas Locality (L) Round Rock Organization (O) Dell Inc. Organizational Unit (OU) Remote Access Group Common Name (CN) iDRAC Default certificate Issuer Information: Country Code (CC) US State (S) Texas Locality (L) Round Rock Organization (O) Dell Inc.
racadm sslcertview -t 1 -A 00 US Texas Round Rock Dell Inc. Remote Access Group iDRAC default certificate US Texas Round Rock Dell Inc. Remote Access Group iDRAC default certificate Jun 7 23:54:19 2011 GMT Jun 4 23:54:19 2021 GMT sslcertdelete Descripti on Command to delete a custom signing certificate from iDRAC. To run this subcommand, you must have the Server Control privilege. Synopsis racadm sslcertdelete -t Input -t — Specifies the type of certificate to delete.
Example Use Remote RACADM to delete the custom signing certificate. $ racadm -r 192.168.1.1 -u root -p calvin sslcertdelete -t 3 sslcsrgen Descripti on Generates and downloads a CSR file to the client’s local file system. The CSR can be used for creating a custom SSL certificate that can be used for SSL transactions on CMC. To run this subcommand, you must have the Configure iDRAC permission.
or racadm sslcsrgen -g -f c:\csr\csrtest.txt • Generate and download a CSR to local filesystem: racadm -r 192.168.0.120 -u root -p calvin sslcsrgen -g -f csrtest.txt NOTE: Before a CSR can be generated, the CSR fields must be configured in the RACADM iDRAC.Security group. For example: racadm set iDRAC.security.commonname MyCompany NOTE: In Telnet/SSH console, you can only generate and not download the CSR file. sslkeyupload Descripti on Uploads SSL key from the client to iDRAC.
To run this subcommand, you must have the Configure iDRAC privilege. Synopsis racadm sslresetcfg Example racadm sslresetcfg Certificate generated successfully and webserver restarted. storage Descripti on Synopsis Allows you to run the commands to control storage arrays. To run this subcommand for configuring the storage properties, you must have the server control permission. • To generate and view information about the inventory of storage root node.
• To generate and view information about the inventory of virtual disks. racadm storage get vdisks racadm storage get vdisks --refkey racadm storage get vdisks --refkey -o racadm storage get vdisks --refkey -o -p • To generate and view information about the inventory of enclosures.
• To get the properties of PCIeSSD physical disk. racadm storage get pdisks: • To generate and view information about the inventory of fans. racadm storage get fans --refkey racadm storage get fans --refkey -o racadm storage get fans --refkey -o -p • To generate and view information about the inventory of EMMs.
{enabled|disabled|default}] [-name ] [-size {b|k|m|g|t}] [-T10PIEnable] racadm storage init: -speed {fast| full} racadm storage deletevd: racadm storage encryptvd: racadm storage createsecuritykey: -key -passwd racadm storage modifysecuritykey: -key -oldpasswd -newpasswd racadm storage deletesecuritykey: racadm storage ccheck: racadm sto
• To start or stop a blink or identify operation on the specified or PCIeSSD device. racadm storage blink: racadm storage blink: racadm storage unblink: racadm storage unblink: • To prepare the PCIeSSD drive for removal. racadm storage preparetoremove • To perform a secure erase on PCIeSSD device. racadm storage secureerase: NOTE: You can also run the command using raid in place of storage.
• • • -name — Specifies the name of the virtual disk. -size — Specifies the size of each virtual disk. – b — Specifies the size in bytes – k — Specifies the size in kilobytes – m — Specifies the size in megabytes – g — Specifies the size in gigabytes – t — Specifies the size in terabytes -sc — Number of spans in a virtual disk (required for multispan RAID level). NOTE: – For PERC9, if the value of controller.
• -speed — specifies the initialization of the Virtual disk. – fast— performs fast initialization. – full— performs slow initialization. • • • • blink: or unblink: — can be physical disk drives or virtual disks. — specifies the PCIeSSD FQDD. — specifies the PCIeSSD controller or enclosure FQDD. preparetoremove — specifies the PCIeSSD drive to prepare for removal.
DriverVersion Available RebuildRate BgiRate CheckConsistencyRate ReconstructRate PatrolReadRate PatrolReadMode PatrolReadState CheckConsistencyMode LoadBalanceSetting CopybackMode PreservedCache CacheMemorySize PersistHotspare SpindownUnconfiguredDrives SpindownHotspare Timeintervalforspindown SecurityStatus Assigned EncryptionMode LKM SasAddress 0x5B8CA3A0F3073700 PciDeviceId PciSubdeviceId PciVendorId PciSubvendorId PciBus PciDevice PciFunction BusWidth SlotLength SlotType MaxCapableSpeed LearnMode T10PIC
This command displays the operations pending on the controller. racadm storage get -pending RAID.Integrated.1-1 raid.Slot.2-1 – To generate and view information about the inventory of batteries connected to the controller. racadm storage get batteries This command is an optimized version and displays the batteries along with their keys. racadm storage get batteries -o Battery.Integrated.1:RAID.Integrated.
Integrated raid Controller 1 OperationalState = Not applicable – To generate and view information about the inventory of virtual disks. racadm storage get vdisks -o Disk.Virtual.2:RAID.Integrated.1-1 120 Status Ok DeviceDescription Virtual Disk 2 on Integrated RAID Controller 1 Name OS RollupStatus Ok State Online OperationalState Not applicable Layout Raid-0 Size 278.
BlockSizeInBytes 512 – To generate and view information about the inventory of storage enclosures connected to the connector. This command displays all enclosure objects for the connector FQDD. racadm storage get enclosures -o Enclosure.Internal.0-1:RAID.Integrated.1-1 Status Ok DeviceDescription Backplane 1 on Connector 0 of Integrated RAID Controller 1 RollupStatus Ok Name BP13G+EXP 0:1 BayId 1 FirmwareVersion 0.
Status = Ok DeviceDescription = Disk 23 in Backplane 1 of Integrated RAID Controller 1 RollupStatus = Ok Name = Physical Disk 0:1:23 State = Online OperationState = Not Applicable PowerStatus = Spun-Up Size = 558.38 GB FailurePredicted = NO RemainingRatedWriteEndurance = Not Applicable SecurityStatus = Not Capable BusProtocol = SAS MediaType = HDD UsedRaidDiskSpace = 136.13 GB AvailableRaidDiskSpace = 0.
This command is an optimized version and displays all disk objects for the enclosure FQDD. racadm storage get pdisks --refkey Enclosure.Internal. 0-1:RAID.Integrated.1-1 -o racadm storage get pdisks -o Disk.Bay.0:Enclosure.Internal.0-1:RAID.Integrated.1-1 Status = Ok DeviceDescription = Disk 0 in Backplane 1 of Integrated raid Controller 1 RollupStatus = Ok Name = Physical Disk 0:1:0 State = Online OperationState = Not Applicable PowerStatus = Spun-Up Size = 278.
This command displays all the fan keys connected to the enclosures. racadm storage get fans --refkey This command displays all the fan objects for the enclosure FQDD. racadm storage get fans --refkey -o racadm storage get fans --refkey -o -p – To generate and view information about the inventory of EMMs connected to the enclosure.
• To get the list of enclosures and properties of the PCIeSSD enclosure. – This command provides the list of enclosures. racadm storage get enclosures Enclosure.Internal.0-1:RAID.Integrated.1-1\ Enclosure.Internal.0-1:PCIeExtender.Slot.3 – This command provides the properties of the specified PCIeSSD enclosure. racadm storage get enclosures:Enclosure.Internal. 0-1:PCIeExtender.Slot.3 Enclosure.Internal.0-1:PCIeExtender.Slot.3 RollupStatus = Ok DeviceDescription = Enclosure.Internal. 0-1:PCIeExtender.Slot.
• To convert the physical disk drive and assign hot-spare. – This command converts the specified non-storage physical disk drive to a storage capable physical disk drive. racadm storage converttoraid:Disk.Bay. 0:Enclosure.Internal.0-0:RAID.Integrated.1-1 – This command converts the specified physical disk drive to a nonstorage physical disk drive. racadm storage converttononraid:Disk.Bay. 0:Enclosure.Internal.0-0:RAID.Integrated.1-1 – This command assigns or unassign a global or dedicated hot-spare.
MediaType = SSD Model = SAMSUNG MZWEI800HAGM 000D3 ProductId = a820 SerialNumber = S1J1NYAD90019 DeviceProtocol = NVMe1.0 Manufacturer = SAMSUNG PCIeNegotiatedLinkWidth = x4 PCIeCapableLinkWidth = x4 MaxCapableSpeed = 8 GT/s NegotiatedSpeed = 8 GT/s FormFactor = 2.5 Inch Revision = IPM0ED35SAM SAMSUNG MZWEI800HAGM 000D3 RemainingRatedWriteEndurance = 100 % FailurePredicted = NO • To reset, clear, and import the storage configuration to the controller.
– This command will blink the specified PCIeSSD device. racadm storage blink:Disk.Bay.8:Enclosure.Internal. 0-1:PCIeExtender.Slot.3 STOR095 : Storage operation is successfully completed. – This command will unblink the specified PCIeSSD device. racadm storage unblink:Disk.Bay.8:Enclosure.Internal. 0-1:PCIeExtender.Slot.3 STOR095 : Storage operation is successfully completed. • To prepare the specified PCIeSSD device for removal racadm storage preparetoremove: Disk.Bay. 8:Enclosure.Internal.
------------------SOFTWARE INVENTORY------------------ComponentType = FIRMWARE ElementName = Power Supply.Slot.2 FQDD = PSU.Slot.2 InstallationDate = 2013-06-11T13:02:46Z Current Version = 07.2B.7D -------------------------------------------------------------ComponentType = FIRMWARE ElementName = Integrated Remote Access Controller FQDD = iDRAC.Embedded.1-1 InstallationDate = NA Rollback Version = 1.50.
NOTE: • • • • • • Synopsis To run this subcommand, you require the Server Profile Export and Import license. Backup operation is licensed (Enterprise) but restore operation is not licensed . If Lifecycle Controller is disabled, starting a restore operation is unsuccessful. If CSIOR is disabled, the system inventory can have old data during the backup operation. An appropriate warning message is displayed. The autobackupscheduler can be enabled or disabled.
• • • • • • • • • -f — Specifies the image location and the file name. NOTE: If the file is in a subfolder within the share location, then specify the network share location in the –l option and specify the subfolder location and the filename in the –f option. -u — Specifies the user name for the remote share access. -p — Specifies the password for the remote share access. --vFlash — Selects vFlash SD as target location for back up. --nopreserve — Deletes all the virtual disks and configurations.
• – If the-wom option is specified, then the valid values for rp are 1–52 – If the-dow option is specified, then the valid values for rp are 1–366. -mb: Specifies the maximum backup parameter. For -vflash maximum backup is 1. NOTE: • • Avoid using the -l, -u, and -p options with --vFlash option. If a backup file is created in a subfolder within the CIFS shared folder, then the subfolder name must be mentioned in the filename option.
• AutoBackup system to CIFS share and encrypt the data. racadm systemconfig backup -f image.img -l // 192.168.2.140/share -u admin -p passwd -n encryptpasswd123 -time 14:30 -dom 1 -rp 6 -mb 10 • AutoBackup system to NFS share and encrypt the data. racadm systemconfig backup -f image.img -l 192.168.2.140:/share -u admin -p passwd -n encryptpasswd123 -time 14:30 -dom 1 -rp 6 -mb 20 • AutoBackup system to vFlash SD.
systemperfstatistics Descripti on Allows you to view and manage the system performance monitoring operations. Synopsis • To view the FQDD's of system performance monitoring sensors racadm systemperfstatistics view • To list the usage statistics of a specific sensor racadm systemperfstatistics • To reset the utilization peaks of system performance monitoring sensors racadm systemperfstatistics PeakReset • To run the peakreset operation you must have configure iDRAC privilege.
Last Week = 0% Peak Readings Last Week 0% [At Mon, 05 May 2014 15:58:35] • To reset the peak utilization of a specific sensor racadm systemperfstatistics PeakReset iDRAC.Embedded. 1#SystemBoardCPUUsageStat RAC1163: The peak utilization value of Out-Of-Band performance monitoring sensor CPU Usage is successfully reset. techsupreport Descripti on Allows you to perform the technical support report operations. The type of operations are: • collect — Collects the technical support report data to export.
• To get the timestamp of the last operating system application data collection. racadm techsupreport getupdatetime • To update the operating system application data collection. racadm techsupreport updateosapp -t • To export the collected report data to local share. racadm techsupreport export -f Input • -t — type of logs.
• To export the collected Tech Support Report, to a CIFS share. racadm techsupreport export -l // 192.168.10.24/share -u myuser -p mypass • To export the collected Tech Support Report, to an NFS share. racadm techsupreport export -l 192.168.10.24:/ share • To export the collected Tech Support Report to the local file system. racadm techsupreport export -f tsr_report.zip testemail Descripti on Sends a test email from iDRAC to a specified destination.
• Make sure that the SMTP IP address is configured properly. racadm set idrac.remotehosts.SMTPServerIPAddress 192.168.0.1 • View the current email alert settings. racadm get idrac.EmailAlert where is a number from 1 to 8. testtrap Descripti on Tests the RAC’s SNMP trap alerting feature by sending a test trap from CMC to a specified destination trap listener on the network. To run this subcommand, you must have the Test Alert permission.
testalert Descripti on Tests FQDN supported SNMP trap notifications. To run this subcommand, you must have the Test Alert User Access. Synopsis racadm testalert -i Input -i — Specifies the index of the trap test. index must be an integer from 1 to 8 on iDRAC. Output Success: Test trap sent successfully Failure: Unable to send test trap Example • Test a trap with index as 1. racadm testalert -i 1 Test trap sent successfully. • Test a trap that has not been configured yet.
traceroute6 Descripti on Traces the network path of routers as the packets traverse from the system to a destination IPv6 address. To run this subcommand, you must have the Execute Diagnostic Commands permission. Synopsis racadm traceroute6 Input IPv6 – Specifies IPv6 address. Output traceroute to fd01::1 (fd01::1) from fd01::3, 30 hops max, 16 byte packets 1 fd01::1 (fd01::1) 14.324 ms 0.26 ms 0.244 ms update Descripti on Allows you to update the firmware of devices on the server.
for CIFS share> -p [-a ] [--verifycatalog] racadm update –f -t -l -u -p racadm update –f -t –e [-a ] [--verifycatalog] racadm update viewreport Input • • • • • • • • • • • • • -f — Update filename for Windows DUP, .d7, .pm, .pm only. For update from repository .
– If the repository has to be through a proxy, then the proxy server address, proxy username and the proxy password must be specified. – The Lifecycle Controller must be enabled for repository update. Output Firmware update job for is initiated. This firmware update job may take several minutes to complete depending on the component or firmware being updated. To view the progress of the job, run the racadm jobqueue view command.
• Perform update from a CIFS repository and to apply the updates, reboot the server. racadm update -f Catalog.xml -l // 192.168.11.10/Repo -u test -p passwd -a TRUE t CIFS • Generate a comparison report using the available updates in the repository. racadm update -f Catalog.xml -l 192.168.11.10:/Repo -t NFS -a FALSE -verifycatalog • Perform update from an FTP repository and to apply the updates, reboot the server. racadm update -f Catalog.xml -e 192.168.11.
usercertupload Descripti on Uploads a user certificate or a user CA certificate from the client to iDRAC. To run this subcommand, you must have the Configure iDRAC permission. Synopsis racadm usercertupload -t [-f ] i Input • • • -t — Specifies the type of certificate to upload, either the CA certificate or server certificate. – 1=user certificate – 2=user CA certificate -f — Specifies the filename of the certificate that must be uploaded.
• Example -i — Index number of the user. Valid values are 2–16. To view user certificate for user 6. racadm usercertview -t 1 -i 6 Serial Number : 01 Subject Information: Country Code (CC) State (S) Locality (L) Organization (O) Common Name (CN) certificate : : : : : US Texas Round Rock Dell Inc. iDRAC default Issuer Information: Country Code (CC) : US State (S) : Texas Locality (L) : Round Rock Organization (O) : Dell Inc.
• Output Status — indicates to view the progress or status report of the initialize operation. If initialization is in progress, the message Initialization of the vFlash SD Card is now in progress is displayed. If unsuccessful, appropriate error message is displayed. If the status of the last operation performed is successful, the message LastAction Progress Status=========================================== ===============Initialize SD Card 100 % Complete is displayed.
NOTE: Creating an empty partition with emulation type as floppy with ext2 format type by using the Telnet session might result in a state where the partition creation status is shown as zero. If this happens then it is recommended to remove the SD card and format it in order to reuse. • • • • • Example Creation of a partition may be unsuccessful if: – The network share is not reachable. – The user name or password provided is not correct. – The file provided does not exist.
• Status of all the existing partitions. racadm vflashpartition status -a • List all the existing partitions and its properties. racadm vflashpartition list vmdisconnect Descripti on Allows you to end another Virtual Media session. After the session ends, the web-based interface reflects the correct connection status. Enables an iDRAC user to disconnect all active Virtual Media sessions.
3 iDRAC Property Database Group and Object Descriptions The iDRAC property database contains the configuration information for iDRAC. Associated object is organizing data, and object group is organizing object. The IDs for the groups and objects that the property database supports are listed in this section for iDRAC Enterprise on Blade Servers and iDRAC Enterprise or Express on Rack and Tower Servers. To configure iDRAC, use the group and object IDs with the RACADM subcommands.
0123456789~`!@#$%^&*()_+-={}[]|\:";'<>,.?/ The following table provides an overview of the object groups applicable for iDRAC Enterprise on Blade Servers and iDRAC on Rack and Tower Servers.
Subcommand iDRAC on Blade Servers iDRAC on Rack and Tower Servers cfgIpmiLan Yes Yes cfgIpmiPetIpv6 Yes Yes cfgIpmiPef Yes Yes cfgIpmiPet Yes Yes cfgUserDomain Yes Yes cfgServerPower Yes Yes cfgServerPowerSupply No Yes cfgIPv6LanNetworking Yes Yes cfgIPv6URL Yes Yes cfgIpmiSerial No Yes cfgSmartCard Yes Yes cfgNetTuning No Yes cfgSensorRedundancy No Yes cfgVFlashSD Yes Yes cfgVFlashPartition Yes Yes cfgLogging Yes Yes cfgRacSecurity Yes Yes cfgIpv6Static
idRacInfo This group contains display parameters to provide information about the specifics of iDRAC being queried. One instance of the group is allowed. The following sections provide information about the objects in the idRACInfo group. idRacProductInfo (Read Only) Descripti on A text string that identifies the product. Legal Values A string of up to 63 ASCII characters.
idRacBuildInfo (Read Only) Descripti on String containing the current RAC firmware build version. Legal Values A string of up to 16 ASCII characters. Default The current iDRAC firmware build version. idRacName (Read Only) Descripti on A user-assigned name to identify this controller. Legal Values A string of up to 15 ASCII characters. Default iDRAC iDRAC Type (Read Only) Descripti on Identifies the remote access controller type.
set of remote management functions for blade servers # idRacVersionInfo=P21 # idRacBuildInfo=200708301525 # idRacName=CMC-1 racadm getconfig -g idRacInfo # idRacType=16 # idRacProductInfo=Integrated Dell Remote Access Controller # idRacDescriptionInfo=This system component provides a complete set of remote management functions for Dell PowerEdge Servers # idRacVersionInfo=1.06.
Default 1 — Enabled NOTE: If this object is modified, then the object cfgNicIPv4Enable is also modified. cfgNicStaticIpAddress (Read or Write) Descripti on Returns or sets the current IPv4 address. Legal Values Any Valid IPv4 address Default 192.168.0.120 NOTE: Only set the current IPv4 address if cfgNicUseDhcp is set to 0(false). cfgNicStaticUseDhcp (Read or Write) Descripti on Specifies whether DHCP is used to configure the IPv4 network.
cfgNicStaticGateway (Read or Write) Descripti on Returns or sets the static IPv4 address. Legal Values Any Valid IPv4 address Default 192.168.0.120 cfgDNSStaticServersFromDHCP (Read or Write) Descripti on Specifies the DNS server static IP addresses. Legal Values • • Default 0 DNS Addresses are configured on the Device DNS Addresses are assigned via DHCP cfgDNSStaticServer1 (Read or Write) Descripti on Specifies the IP address for DNS server 1.
cfgDNSStaticServer2(Read or Write) Descripti on Specifies the static IP address for DNS server 2. Legal Values A Valid IPv4 Address Default 0.0.0.0 cfgDNSStaticDomainName(Read or Write) Descripti on The DNS static domain name. Legal Values String of up to 254 ASCII characters. Characters are restricted to alphanumeric, hyphens and periods. At least one of the characters must be alphabetic.
To apply this setting to iDRAC, use the —m option. Use this object with the config or getconfig subcommands. The following sections provide information about the objects in the cfgRemoteHosts group. cfgRhostsFwUpdateTftpEnable (Read or Write) Descripti on Enables or disables firmware update from a network TFTP server.
cfgRhostsSmtpServerIpAddr (Read or Write) Descripti on The IPv4 or IPv6 address of the network SMTP server. Legal Values A string representing a valid SMTP server IPv4 or IPv6 address. For example: 192.168.0.55. Default For IPv4, it is 0.0.0.0 The SMTP server transmits email alerts from iDRAC if the alerts are configured and enabled. cfgRhostsSyslogEnable (Read or Write) Descripti on To allow the RAC and SEL logs to be written to up to three remote syslog servers Enables or disables remote syslog.
cfgRhostsSyslogServer2 (Read or Write) Descripti on To store the RAC and SEL logs Specify the second of three possible remote syslog servers. This property is only valid if cfgRhostsSyslogEnable is set to 1 (enabled). Legal Values String from 0 to 63 characters. Default cfgRhostsSyslogServer3 (Read or Write) Descripti on To store the RAC and SEL logs specify the third of three possible remote syslog servers. This property is only valid if cfgRhostsSyslogEnable is set to 1(enabled).
cfgUserAdminIndex (Read Only) Descripti on The unique index of a user. Legal Values This parameter is populated based on the existing instances. Default cfgUserAdminIpmiLanPrivilege (Read or Write) Descripti on The maximum privilege on the IPMI LAN channel. This object property is specific to iDRAC.
cfgUserAdminPrivilege (Read or Write) Descripti on This property specifies the role-based authority privileges allowed for the user. The value is represented as a bit mask that allows for any combination of privilege values. The table below describes the user privilege bit values that can be combined to create bit masks.
Control Comman ds Access Virtual Console 0x00000020 Access Virtual Media 0x00000040 Test Alerts 0x00000080 Execute Debug Comman ds 0x00000100 CMC Specific User Privilege CMC Login User 0x0000001 Chassis 0x0000002 Configura tion Administr ator User 0x0000004 Configura tion Administr ator Clear Logs Administr ator 0x0000008 163
Chassis Control Administr ator 0x0000010 Super User 0x0000020 Server Administr ator 0x0000040 Test Alert User 0x0000080 Debug Comman d Administr ator 0x0000100 Fabric A Administr ator 0x0000200 Fabric B Administr ator 0x0000400 Fabric C Administr ator 0x0000800 Examples The following table provides sample privilege bit masks for users with one or more privileges.
to access iDRAC or CMC The user 0x00000001 may only log in to iDRAC or CMC and view iDRAC or CMC and server configura tion informati on. The user 0x00000001 + 0x00000002 = 0x00000003 may log in to iDRAC or CMC and change configura tion. The user may log in to iDRAC, access Virtual Media, and Virtual Console. 0x00000001 + 0x00000040 + 0x00000080 = 0x000000C1 cfgUserAdminUserName (Read or Write) Descripti on The name of the user for this index. Writing a string of double quotes (" ") disables the user.
NOTE: This property value must be unique among user names. Legal Values A string of up to 16 ASCII characters. Default • • root (User 2) (All others) cfgUserAdminPassword (Write Only) Descripti on The password for this user. User passwords are encrypted and cannot be seen or displayed after the property is written. Legal Values A string of up to 20 ASCII characters. Default ******** cfgUserAdminEnable (Read or Write) Descripti on Enables or disables an individual user.
Default 0 cfgEmailAlert This group contains parameters to configure iDRAC email alerting capabilities. Up to four instances of this group are allowed. Use this object with the config or getconfig subcommands. The following sections provide information about the objects in the cfgEmailAlert group. cfgEmailAlertIndex (Read Only) Descripti on The unique index of an alert instance.
cfgEmailAlertCustomMsg (Read or Write) Descripti on Specifies a custom message that forms the subject of the alert. Legal Values A string of up to 32 characters Default This object property is specific to iDRAC. cfgEmailAlertEmailName (Read Only) Descripti on Specifies name or other identifier associated with the destination email address. The email name can refer to an individual, group, location, department, and so on. This object property is specific to CMC.
The following sections provide information about the objects in the cfgSessionManagement group. cfgSsnMgtRacadmTimeout (Read or Write) Descripti on Defines the idle timeout in seconds for the Remote RACADM interface. If a remote RACADM session remains inactive for more than the specified sessions, the session closes.
An expired web server session logs out the current session. Legal Values 60–10800 Default 1800 cfgSsnMgtSshIdleTimeout (Read or Write) Descripti on Defines the secure shell idle time-out. This property sets the amount of time (in seconds) that a connection is allowed to remain idle (there is no user input). The session is canceled if the time limit exceeds this property. Changes to this setting do not affect the current session; log out and log in again to make the new settings effective.
current session (you must log out and log in again to make the new settings effective.) An expired Telnet session displays the following error message: • • For iDRAC on Rack and Tower Servers: Connection timed out For iDRAC Enterprise on Blade Servers: Session timed out. Closing the session. After the message is displayed, the system returns you to the shell that generated the Telnet session.
cfgSerialBaudRate (Read or Write) Descripti on Sets the baud rate on the serial port. Legal Values 9600, 28800, 57600, 115200 Default 57600 cfgSerialConsoleEnable (Read or Write) Descripti on Enables or disables the serial console interface. Legal Values • • Default 0 1 (TRUE) 0 (FALSE) cfgSerialConsoleQuitKey (Read or Write) Descripti on This key or key combination terminates Virtual Console text for iDRAC when using the console com2 command.
NOTE: For more information about running the RACADM commands for special characters, see Guidelines to Quote Strings Containing Special Characters. cfgSerialConsoleIdleTimeout (Read or Write) Descripti on The maximum number of seconds to wait before an idle serial session is disconnected. Legal Values • • Default 300 0 = No timeout 60–1920 cfgSerialConsoleNoAuth (Read or Write) Descripti on Enables or disables the serial console login authentication.
Defaul t 8192 cfgSerialCom2RedirEnable (Read or Write) Descripti on Enables or disables the console for COM 2-port redirection. Legal Values • • Default 1 The cfgSerialCom2RedirEnable object property is applicable only for iDRAC on Rack and Tower Servers. 1 (TRUE) 0 (FALSE) cfgSerialHistorySize (Read or Write) Descri ption Specifies the maximum size of the serial history buffer.
cfgSerialConsoleCommand= cfgSerialConsoleColumns=0 cfgSerialHistorySize=8192 cfgSerialTelnetEnable=0 cfgSerialSshEnable=1 cfgSerialTelnetEnable (Read or Write) Descripti on Enables or disables the Telnet console interface. Legal Values • • Default 0 1 (TRUE) 0 (FALSE) cfgOobSnmp This group contains parameters to configure the SNMP agent and trap capabilities of iDRAC. One instance of the group is allowed.
Example racadm getconfig -g cfgOobSnmp cfgOobSnmpTrapsEnable=1 cfgOobSnmpAgentCommunity=public cfgOobSnmpAgentEnable (Read or Write) Descripti on Enables or disables the SNMP agent in iDRAC. Legal Values • • Default 0 1 (TRUE) 0 (FALSE) cfgRacTuning This group is used to configure various configuration properties, such as valid ports and security port restrictions. Use this object with the config or getconfig subcommands. To apply this setting to iDRAC, use the —m option.
cfgRacTuneRemoteRacadmEnable (Read or Write) Descripti on Enables or disables the Remote RACADM interface. Legal Values • • Default 1 1 (TRUE) 0 (FALSE) cfgRacTuneCtrlEConfigDisable Descripti on To configure iDRAC from the BIOS POST option-ROM, enables or disables the ability of the local user. This object is applicable only for iDRAC on Rack and Tower Servers and not for iDRAC Enterprise on Blade Servers.
Default 443 cfgRacTuneIpRangeEnable (Read or Write) Descripti on Enables or disables the IPv4 Address Range validation feature. Legal Values • • Default 0 1 (TRUE) 0 (FALSE) cfgRacTuneIpRangeAddr (Read or Write) Descripti on Specifies the acceptable IPv4 address bit pattern in the positions of the "1"s in the range mask property (cfgRacTuneIpRangeMask). Legal Values An IPv4 address formatted string, for example, 192.168.0.44. Default 192.168.1.
Default 0 cfgRacTuneIpBlkFailCount (Read or Write) Descripti on The maximum number of logins that is not successful, to occur within the window (cfgRacTuneIpBlkFailWindow) before log in attempt from the IP address is rejected. Legal Values 2–16 Default 5 cfgRacTuneIpBlkFailWindow (Read or Write) Descripti on Defines the time span in seconds that the unsuccessful attempts are counted. When unsuccessful attempts age beyond this limit, they are dropped from the count.
Default 22 cfgRacTuneTelnetPort (Read or Write) Descripti on Specifies the port number used for the Telnet interface. Legal Values 1–65535 Default 23 cfgRacTuneConRedirEnable (Read or Write) Descripti on Enables or disables Virtual Console. Legal Values • • Default 1 This object property is applicable only to iDRAC. 1 (TRUE) 0 (FALSE) cfgRacTuneConRedirEncryptEnable (Read or Write) Descripti on Encrypts the video in a Virtual Console session.
This object property is applicable only to iDRAC and requires an iDRAC reset before it becomes active. Legal Values • • Default 0 1 (TRUE) 0 (FALSE) cfgRacTuneDaylightOffset (Read Only) Descripti on Specifies the daylight savings offset (in minutes) to use for the RAC Time. This value is 0 if the time zone is not a Daylight Saving time zone.
cfgRacTuneTimezoneOffset (Read Only) Descripti on Specifies the time zone offset (in minutes) from Greenwich Mean Time (GMT) / Coordinated Universal Time (UTC) to use for the RAC Time.
Default 1 cfgRacTuneLocalConfigDisable (Read or Write) Descripti on Disables write access to iDRAC configuration data. NOTE: Access can be disabled using the local RACADM or iDRAC web interface; however, once disabled, access can be re-enabled only through iDRAC web interface. This object property is applicable only to iDRAC. Legal Values • • Default 0 0 (TRUE-Enables) 1 (FALSE-Disables) cfgRacTuneWebserverEnable (Read or Write) Descripti on Enables or disables the web server.
NOTE: To modify this property, you must have Configure iDRAC permission. This object can be used only with remote or firmware (SSH or Telnet) RACADM and not with local RACADM or with earlier DRAC products. Legal Values 0 — (If the user of the first session has not responded for session sharing request by subsequent user. The next session user gets an access denied error after the default timeout value of 30 seconds.
ifcRacMnOsHostname (Read Only) Descripti on The host name of the managed server. Legal Values A string of up to 255 characters. Default ifcRacMnOsOsName (Read Only) Descripti on The operating system name of the managed server. Legal Values A string of up to 255 characters. Default cfgRacVirtual This group contains parameters to configure the iDRAC Virtual Media feature. One instance of the group is allowed.
NOTE: Modifying this property does not impact the remote file sharing operation. Legal Values • • • Default 0 0 = Detach 1 = Attach 2 = AutoAttach cfgVirtualBootOnce (Read or Write) Descripti on Enables or disables the Virtual Media Boot Once feature of iDRAC. If this property is enabled when the host server is rebooted, this feature attempts to start from the virtual media devices — if the appropriate media is installed in the device.
cfgSDWriteProtect (Read Only) Descripti on Displays if the physical write protect latch on the SD card is enabled or disabled. NOTE: This command is deprecated from 12G iDRAC 1.0 release onwards. The functionality of this command is covered by cfgVFlashSDWriteProtect. While execution of the cfgSDWriteProtect command is successful, use the cfgVFlashSDWriteProtect command. For more information, see cfgVFlashSDWriteProtect Read Only.
cfgServerNic3MacAddress (Read Only) Descripti on Displays the MAC address of the server NIC 3. Legal Values None Default None cfgServerNic4MacAddress (Read Only) Descripti on Displays the MAC address of the server NIC 4. Legal Values None Default None cfgServerDNSIMCName (Read or Write) Descripti on Displays the DNS domain name for the integrated Remote Access Controller (iDRAC).
NOTE: First attach, to configure vFlash as First Boot Device. When a detached / non-existent vFlash partition or a nonstandard boot device is configured as first boot device, the following error message is displayed: Invalid object value Legal Values • • • • • • • • • • • • • • No-Override PXE HDD DIAG CD-DVD BIOS vFDD VCD-DVD iSCSI FDD SD RFS (Remote File Share) F10 F11 Default No-Override cfgServerBootOnce (Read or Write) Descripti on Enables or disables the server start once feature.
The following sections provide information about the objects in the cfgActiveDirectory. cfgADSSOEnable (Read or Write) Descripti on Enables or disables Active Directory single sign-on authentication on iDRAC. Legal Values • • Default 0 1 (TRUE) 0 (FALSE) cfgADDomainController1 (Read or Write) Descripti on To obtain user names, specify the LDAP server from which you want the iDRAC. This object is applicable only to iDRAC.
cfgADDomainController3 (Read or Write) Descripti on To obtain user names, specify the LDAP server from which you want the iDRAC. This object is applicable only to iDRAC. Legal Values A string of up to 254 ASCII characters representing a valid IP address or a fully qualified domain name (FQDN). Default None cfgADRacName (Read or Write) Descripti on Name of iDRAC as recorded in the Active Directory forest. Legal Values Any printable text string of up to 254 characters, with no white space.
Default 120 cfgADEnable (Read or Write) Descripti on Enables or disables Active Directory user authentication on iDRAC. If this property is disabled, only local iDRAC authentication is used for user login. Legal Values • • Default 0 1 (TRUE) 0 (FALSE) cfgADType (Read or Write) Descripti on To use the Active Directory, determine the schema type.
cfgADGlobalCatalog2 (Read or Write) Descripti on To obtain user names, specify the Global Catalog server from which you want the iDRAC. This object is applicable only to iDRAC. Legal Values A string of up to 254 ASCII characters representing a valid IP address or a fully qualified domain name (FQDN). Default None cfgADGlobalCatalog3 (Read or Write) Descripti on To obtain user names, specify the Global Catalog server from which you want the iDRAC. This object is applicable only to iDRAC.
specified under cfgAdDomainController1 ,cfgAdDomainController2 and cfgAdDomainController3. iDRAC does not failover to the specified domain controllers when DNS lookup is unsuccessful or none of the servers returns to the DNS lookup works. This object is applicable only to iDRAC.
cfgADGcSRVLookupEnable (Read or Write) Descripti on Determines how the global catalog server is looked up. If using pre‑configured global catalog servers, then iDRAC uses the values cfgAdGlobalCatalog1, cfgAdGlobalCatalog2 and cfgAdGlobalCatalog3. This object is applicable only to iDRAC.
If this property is disabled, local CMC authentication is used for user logins. Legal Values • • Default 0 1 (TRUE) — Enable 0 (FALSE) — Disable cfgLdapServer (Read or Write) Descripti on Configures the address of the LDAP Server. IPv4 and IPv6 are supported. NOTE: You can specify multiple servers by separating each server with a comma. For example, example.com, sub1.example.com Legal Values String.
Default Null cfgLdapUserAttribute (Read or Write) Descripti on To search for, specify the user attribute. It is recommended to be unique within the chosen baseDN, otherwise a search filter must be configured to make sure the uniqueness of the login user. If the userDN cannot be uniquely identified, login is unsuccessful with error. Legal Values String. Maximum length = 254 Default Null uid if not configured.
Default 1 cfgLdapBinddn (Read/Write) Descripti on The distinguished name of a user used to bind to the server when searching for the login user's DN. If not provided, an anonymous bind is used. If necessary It is optional to support anonymous bind. NOTE: If cfgLDAPBindDN is [null] and cfgLDAPBindPassword is [null], then the CMC attempts an anonymous bind. Legal Values String. Maximum length = 254 Default Null cfgLdapBindpassword (Write Only) Descripti on A bind password is used with the bindDN.
cfgLDAPCertValidationEnable (Read or Write) Descripti on Controls certificate validation during SSL handshake. Legal Values • Default • 1 (TRUE) — Uses the CA certificate to validate the LDAP server certificate during SSL handshake. 0 (FALSE) —Skips the certificate validation step of SSL handshake. 1 cfgLDAPSRVLookupDomainName (Read Only) Descripti on To use in the SRV lookup, configure the domain name. Legal Values String of maximum length of 254 alphanumeric characters and hyphens.
• cfgLDAPRoleGroupDN — an LDAP distinguished name (DN) • cfgLDAPRoleGroupPrivilege — a CMC privilege map Each LDAP-authenticated user assumes the total set of CMC privileges assigned to the matching LDAP distinguished names that the user belongs to. That is, if the user belongs to multiple role group DNs, the user receives all associated privileges for that DNs. The following sections provide information about the objects in the cfgLdapRoleGroup.
Default 0x000 Example racadm getconfig -g cfgLDAPRoleGroup -o cfgLDAPRoleGroupPrivilege -i 1 0x0 cfgStandardSchema This group contains parameters to configure the Active Directory standard schema settings. Use this object with the config or getconfig subcommands. The following sections provide information about the objects in the cfgStandardSchema. cfgSSADRoleGroupIndex (Read Only) Descripti on Index of the Role Group as recorded in the Active Directory.
cfgSSADRoleGroupDomain (Read or Write) Descripti on Active Directory Domain in which the Role Group resides. Legal Values Any printable text string of up to 254 characters, with no white space. Default cfgSSADRoleGroupPrivilege (Read or Write) Descripti on Use the bit mask numbers listed in the table below to set rolebased authority privileges for a Role Group.
Execute Server Control Commands 0x00000010 Access Virtual Console 0x00000020 Access Virtual Media 0x00000040 Test Alerts 0x00000080 Execute Debug Commands 0x00000100 cfgThermal This group displays and configures the thermal settings. Use this object with the config or getconfig subcommands. To set the configurations, you must have the Chassis Configuration Administrator privileges. cfgThermalEnhancedCoolingMode Descripti on Configures the enhanced cooling mode.
cfgIpmiSolEnable (Read or Write) Descripti on Enables or disables SOL. Legal Values • • Default 1 1(TRUE) 0(FALSE) cfgIpmiSolBaudRate (Read or Write) Descripti on Specifies baud rate for serial communication over LAN. Legal Values 9600, 19200, 57600, 115200 Default 115200 cfgIpmiSolMinPrivilege (Read or Write) Descripti on Specifies the minimum privilege level required for SOL access.
Default 10 cfgIpmiSolSendThreshold (Read or Write) Descripti on To buffer before sending an SOL data packet, specify the SOL threshold limit value and the maximum number of bytes. Legal Values 1–255 Default 255 cfgIpmiLan This group is used to configure the IPMI over LAN capabilities of the system. The following sections provide information about the objects in the cfgIpmiLan group. cfgIpmiLanEnable (Read or Write) Descripti on Enables or disables the IPMI over LAN interface.
cfgIpmiLanAlertEnable (Read or Write) Descripti on Enables or disables global email alerting. This property overrides all individual email alerting enable or disable properties. Legal Values • • Default 0 1(TRUE) 0(FALSE) cfgIpmiLanEncryptionKey (Read or Write) Descripti on Specifies the IPMI encryption key. Legal Values A string of hexadecimal digits from 0 to 40 characters with no spaces. Only an even number of digits is allowed.
cfgIpmiPetIPv6Index (Read Only) Descripti on Unique identifier for the index corresponding to the trap. Legal Values 1–4 Default cfgIpmiPetIPv6AlertDestIpAddr Descripti on Configures the IPv6 alert destination IP address for the trap. Legal Values IPv6 address Default cfgIpmiPetIPv6AlertEnable (Read or Write) Descripti on Enables or disables the IPv6 alert destination for the trap.
cfgIpmiPefName (Read Only) Descripti on Specifies the name of the platform event filter. Legal Values A string of up to 255 characters. Default The name of the index filter. cfgIpmiPefIndex (Read or Write) Descripti on Specifies the index of a specific platform event filter. Legal Values • • Default The index value of a platform event filter object.
cfgIpmiPefEnable (Read or Write) Descripti on Enables or disables a specific platform event filter. Legal Values • • Default 1 1(TRUE) 0(FALSE) cfgIpmiPet This group is used to configure platform event traps on the managed server. The following sections provide information about the objects in the cfgIpmiPet group. cfgIpmiPetIndex (Read Only) Descripti on Unique identifier for the index corresponding to the trap. Legal Values 1–4 Default The index value of a specific platform event trap.
cfgIpmiPetAlertEnable (Read or Write) Descripti on Enables or disables a specific trap. Legal Values • • Default 0 1 (TRUE) 0 (FALSE) cfgUserDomain This group is used to configure the Active Directory user domain names. A maximum of 40 domain names can be configured at any given time. The following sections provide information about the objects in the cfgUserDomain group. cfgUserDomainIndex (Read Only) Descripti on Represents a specific domain. Legal Values 1–40 Default The index value.
cfgServerPower This group provides several power management features. The following sections provide information about the objects in the cfgServerPower group. cfgServerPowerStatus (Read Only) Descripti on Represents the server power state, either ON or OFF. Legal Values • • Default 0 1 (ON) 0 (OFF) cfgServerPowerAllocation (Read Only) Descripti on Represents the available allocated power supply for server usage.
cfgServerActualPowerConsumption (Read Only) Descripti on Represents the power consumption by the server at the current time. Legal Values Not applicable Default cfgServerPowerCapEnable (Read or Write) Descripti on Enables or disables the user specified power budget threshold. Legal Values • • Default 1 This object is Read only for iDRAC Enterprise on Blade Servers.
cfgServerPeakPowerConsumption (Read Only) Descripti on Represents the servers maximum power consumption until the current time. Legal Values Not applicable Default Peak power consumption of the server cfgServerPeakPowerConsumptionTimestamp (Read Only) Descripti on Specifies time when the maximum power consumption was recorded. Legal Values A string of up to 32 characters. Default Timestamp of the peak power consumption of the server.
Default Server power threshold in Watts. cfgServerPowerCapBtuhr (Read or Write) Descripti on Represents the server power threshold in BTU/hr. Legal Values None Default Server power threshold in BTU/hr. NOTE: This value is applicable only if cfgServerPowerCapEnable is set to 1. cfgServerPowerCapPercent (Read or Write) Descripti on Represents the server power threshold in percentage. Legal Values None Default Server power threshold in percentage.
cfgServerPowerLastDayAvg (Read Only) Descripti on Displays the average power value during the last day. Legal Values None Default Average power value during the last day. cfgServerPowerLastWeekAvg (Read Only) Descripti on Displays the average power value during the last week. Legal Values None Default Average power value during the last week. cfgServerPowerLastHourMinPower (Read Only) Descripti on Displays the minimum power value during the last hour.
• • • • • • Default MM= Month Date=Date YYYY = Year HH = hour MM=Minutes SS = Seconds Minimum power value during the last minute. cfgServerPowerLastHourMaxPower (Read Only) Descripti on Displays the maximum power value during the last hour. Legal Values Not applicable Default Maximum power value during the last hour. cfgServerPowerLastHourMaxTime (Read Only) Descripti on Displays the timestamp of maximum power value during the last hour.
cfgServerPowerLastDayMinPower (Read Only) Descripti on Displays the minimum power value during the last day. Legal Values Not applicable Default Minimum power value during the last day. cfgServerPowerLastDayMinTime (Read Only) Descripti on Displays the timestamp of minimum power value during the last day.
cfgServerPowerLastDayMaxTime (Read Only) Descripti on Displays the timestamp of maximum power value during the last day. Legal Values Time in the format: DD MM Date HH:MM:SS YYYY where, • • • • • • • Default DD = Day of the week MM = Month Date = Date YYYY = Year HH = hour MM = Minutes SS = Seconds Timestamp of the maximum power value during the last day. cfgServerPowerLastWeekMinPower (Read Only) Descripti on Displays the minimum power value during the last week.
• • • • • Default Date = Date YYYY = Year HH = hour MM = Minutes SS = Seconds Timestamp of the minimum power value during the last week. cfgServerPowerLastWeekMaxPower (Read Only) Descripti on Displays the maximum power value during the last week. Legal Values None Default Maximum power value during the last week. cfgServerPowerLastWeekMaxTime (Read Only) Descripti on Displays the timestamp of maximum power value during the last week. Legal Values A string of up to 32 characters.
cfgServerPowerInstHeadroom (Read Only) Descripti on Displays the difference between the available power and the current power consumption. This object is applicable only for iDRAC on Rack and Tower Servers and not for iDRAC Enterprise on Blade Servers. Legal Values Not applicable Default Difference between the available power and the current power consumption. cfgServerPowerPeakHeadroom (Read Only) Descripti on Displays the difference between the available power and the peak power consumption.
cfgServerPeakAmperage (Read Only) Descripti on Displays the current peak power consumption. Legal Values Not applicable Default Current peak power consumption. cfgServerPeakAmperageTimeStamp (Read Only) Descripti on Displays the timestamp of the current peak power consumption. Legal Values A string of up to 32 characters.
cfgServerCumulativePowerConsumptionTimeStamp (Read Only) Descripti on Displays the timestamp of the cumulative power consumption. Legal Values A string of up to 32 characters. Time in the format: DD MM Date HH:MM:SS YYYY where, • • • • • • • Default DD = Day of the week MM= Month Date=Date YYYY = Year HH = hour MM=Minutes SS = Seconds Timestamp of the cumulative power consumption.
You must have the Administrator privileges to modify the value for this object. Legal Values Default 0 W: For platforms that do not support PCIe cards. 100 W — 500 W: For platforms that support PCIe cards. 0: For platforms that do not support PCIe cards. 500 W: For platforms that support PCIe cards. cfgServerPowerSupply This group contains information related to the power supplies.
cfgServerPowerSupplyMaxInputPower (Read Only) Descripti on Displays the AC input rated power in Watts. Legal Values A string of up to 32 characters. Default 0 cfgServerPowerSupplyMaxOutputPower (Read Only) Descripti on Displays the AC output rated power in Watts. Legal Values A string of up to 32 characters. Default 0 cfgServerPowerSupplyOnlineStatus (Read Only) Descripti on Displays the status of the PSU.
cfgServerPowerSupplyCurrentDraw (Read Only) Descripti on Displays the instantaneous current consumption in 0.1 amps. Legal Values A string of up to 32 characters. Default 0 cfgServerPowerSupplyType Descripti on Displays whether the power supply is AC or DC. Legal Values A string of up to 32 characters. Default 0 cfgIPv6LanNetworking This group is used to configure the IPv6 over LAN networking capabilities. Use this object with the config or getconfig subcommands.
cfgIPv6Address1 (Read or Write) Descripti on Specifies iDRAC IPv6 address. Legal Values String representing a valid IPv6 entry. Default : cfgIPv6Gateway (Read or Write) Descripti on iDRAC gateway IPv6 address. Legal Values Specifies string representing a valid IPv6 entry. Default : cfgIPv6AutoConfig (Read or Write) Descripti on Enables or disables the IPv6 Auto Configuration option. NOTE: If this value is set to 0, the CMC disables auto configuration and statically assigns IPv6 addresses.
cfgIPv6PrefixLength (Read or Write) Descripti on Specifies the prefix length for IPv6 address. NOTE: • Legal Values 1–128 Default 64 This property can be configured even when cfgIPv6AutoConfig is enabled. cfgIPv6LinkLocalAddress (Read Only) Descripti on The iDRAC IPv6 link local address. Legal Values Specifies a string representing a valid IPv6 entry. Default : cfgIPv6Address2 (Read Only) Descripti on The iDRAC IPv6-second address. Legal Values A string representing a valid IPv6 entry.
Default : cfgIPv6Address4 (Read Only) Descripti on The iDRAC IPv6 fourth address. Legal Values String representing a valid IPv6 entry. Default : cfgIPv6Address5 (Read Only) Descripti on The iDRAC IPv6 fifth address. Legal Values String representing a valid IPv6 entry. Default : cfgIPv6Address6 (Read Only) Descripti on The iDRAC IPv6 sixth address. Legal Values String representing a valid IPv6 entry. Default : cfgIPv6Address7 (Read Only) Descripti on The iDRAC IPv6 seventh address.
cfgIPv6Address8 (Read Only) Descripti on The iDRAC IPv6 eighth address. Legal Values String representing a valid IPv6 entry. Default : cfgIPv6Address9 (Read Only) Descripti on The iDRAC IPv6 ninth address. Legal Values String representing a valid IPv6 entry. Default : cfgIPv6Address10 (Read Only) Descripti on The iDRAC IPv6 tenth address. Legal Values String representing a valid IPv6 entry. Default : cfgIPv6Address11 (Read Only) Descripti on The iDRAC IPv6 eleventh address.
cfgIPv6Address12 (Read Only) Descripti on The iDRAC IPv6 twelfth address. Legal Values String representing a valid IPv6 entry. Default : cfgIPv6Address13 (Read Only) Descripti on The iDRAC IPv6 thirteenth address. Legal Values String representing a valid IPv6 entry. Default : cfgIPv6Address14 (Read Only) Descripti on The iDRAC IPv6 fourteenth address. Legal Values String representing a valid IPv6 entry. Default : cfgIPv6Address15 (Read Only) Descripti on The iDRAC IPv6 fifteenth address.
cfgIPv6DNSServersFromDHCP6 (Read or Write) Descripti on Specifies whether cfgIPv6DNSServer1 and cfgIPv6DNSServer2 are static or DHCP IPv6 addresses. NOTE: This property is used only if cfgIPv6AutoConfig is set to 1(true). Legal Values 1 (TRUE) Default 0 0 (FALSE) cfgIPv6DNSServer1 (Read/Write) Descripti on Specifies the IPv6 DNS server address. Legal Values A string representing a valid IPv6 entry.
Example $ racadm getconfig -g cfgIPv6LanNetworking cfgIPv6Enable=1 cfgIPv6AutoConfig=1 cfgIPv6Address=:: cfgIPv6PrefixLength=64 cfgIPv6Gateway=:: cfgIPv6DNSServersFromDHCP6=1 cfgIPv6DNSServer1=:: cfgIPv6DNSServer2=:: If both IPv4 and IPv6 are enabled on the CMC, IPv6 DNS servers take priority.
cfgIPv6StaticAddress1 (Read or Write) Descripti on Returns or sets the static IPv6 address1. Legal Values Any IPv6 address NOTE: Only set the current IPv4 address if cfgNicUseDhcp is set to 0 (false). Default cfgIPv6StaticGateway (Read or Write) Descripti on Returns or sets gateway static IPv6 address. Legal Values Any IPv6 address Default cfgIPv6StaticPrefixLength (Read or Write) Descripti on The prefix length for static IPv6 address 1.
NOTE: If this object is modified, then the object cfgIPv6Autoconfig is also modified. cfgIPv6StaticDNSServersFromDHCP6 (Read or Write) Descripti on Specifies the DNS server static IP addresses. Legal Values • • Default 0 — Disabled 0 — DNS Server must be configured as static. 1 — The device will get the DNS servers from DHCPv6. cfgIPv6StaticDNSServer1 (Read or Write) Descripti on Specifies the DNS server 1 static IPv6 address.
cfgIPv6URLstring (Read Only) Descripti on The iDRAC IPv6 URL. Legal Values A string of up to 80 characters. Default cfgIpmiSerial This group specifies properties used to configure the IPMI serial interface of the BMC. It is applicable only for iDRAC on Rack and Tower Servers and not for iDRAC Enterprise on Blade Servers. cfgIpmiSerialBaudRate (Read or Write) Descripti on Specifies the baud rate for a serial connection over IPMI.
cfgIpmiSerialConnectionMode (Read or Write) Descripti on When the iDRAC cfgSerialConsoleEnable property is set to 0(disabled), the iDRAC serial port becomes the IPMI serial port. This property determines the IPMI defined mode of the serial port. In Basic mode, the port uses binary data with the intent of communicating with an application program on the serial client. In Terminal mode, the port assumes that a dumb ASCII terminal is connected and allows simple commands to be entered.
cfgIpmiSerialFlowControl (Read or Write) Descripti on Specifies the flow control setting for the IPMI serial port. Legal Values • • Default 1 0 (None) 1 (CTS or RTS) cfgIpmiSerialHandshakeControl (Read or Write) Descripti on Enables or disables the IPMI terminal mode handshake control. Legal Values • • Default 1 0(FALSE) 1 (TRUE) cfgIpmiSerialNewLineSequence (Read or Write) Descripti on Specifies the new line sequence specification for the IPMI serial interface.
cfgIpmiSerialLineEdit (Read or Write) Descripti on Enables or disables line editing on the IPMI serial interface. Legal Values • • Default 1 0(FALSE) 1(TRUE) cfgIpmiSerialInputNewLineSequence (Read or Write) Descripti on Specifies the input new line sequence specification for the IPMI serial interface. Legal Values • • Default 1 1 — ENTER 2 — NULL cfgSmartCard This group specifies properties used to support access to iDRAC using a smart card.
• Default 2 (Enabled with Remote RACADM) — It is not applicable for iDRAC Enterprise on Blade Servers. 0 cfgSmartCardCRLEnable (Read or Write) Descripti on Enables or disables the Certificate Revocation List (CRL). This object is applicable only for iDRAC on Rack and Tower Servers and not for iDRAC Enterprise on Blade Servers. Legal Values • • Default 0 1 (TRUE) 0 (FALSE) cfgNetTuning This group enables users to configure the advanced network interface parameters for the RAC NIC.
Default 1 Example racadm getconfig -g cfgNetTuning cfgNetTuningNicSpeed=100 cfgNetTuningNicFullDuplex=1 cfgNetTuningNicMtu=1500 cfgNetTuningNicAutoneg=1 cfgNetTuningNic100MB (Read or Write) Descripti on Specifies the speed for iDRAC NIC. Legal Values • • • NOTE: To set this property: • iDRAC Nic selection must be set to Dedicated mode. • iDRAC Nic Auto negotiation must be disabled. • iDRAC IPv4 must be enabled. • iDRAC IPv4 DHCP must be enabled. • iDRAC IPv6 must be enabled.
Default 1 cfgNetTuningNicMtu (Read or Write) Descripti on Indicated the maximum size of units in bytes transmitted by NIC. Legal Values 576–1500 Default 1500 cfgSensorRedundancy This group is used to set the power supply redundancy. The following sections provide information about the objects in the cfgSensorRedundancy group. This group is applicable only for iDRAC on Rack and Tower Servers and not for iDRAC Enterprise on Blade Servers.
• Default 16–2+2 Redundant Any legal value at that particular execution instance. cfgSensorRedundancyCapabilities (Read Only) Descripti on Returns the redundancy capabilities in the form of a bitmask. This bitmask allows the user to know which values can be set for cfgSensorRedundancyPolicy. Legal Values A bit mask. More than 1 bit can be set at a time to indicate multiple redundancy support.
NOTE: If the vFlash card is present but is not enabled, the query for any property under this group displays: ERROR: vFlash is not enabled. To view the properties of this group, enable the vFlash using the command: racadm config -g cfgvFlashSD -o cfgvFlashSDEnable 1 The following sections provide information about the objects in the cfgVFlashSD group. cfgVFlashSDInitialized (Read Only) Descripti on Displays whether an SD card is initialized.
cfgVFlashSDLicensed (Read Only) Descripti on Displays whether an SD card or vFlash SD card is inserted. The vFlash SD card supports the new enhanced vFlash features and the SD card supports only the limited vFlash features. Legal Values • • Default None 0(SD card is inserted) 1(vFlash SD card is inserted) cfgVFlashSDAvailableSize (Read Only) Descripti on Displays the available memory (in MB) on the vFlash SD card that can be used to create new partitions.
cfgVFlashSDWriteProtect (Read Only) Descripti on Displays whether the physical WriteProtect latch on the vFlash SD card is enabled or disabled. Legal Values • • Default None 0 (vFlash is not write-protected) 1 (vFlash is write-protected) cfgVFlashPartition This group is used to configure properties for individual partitions on the vFlash SD Card. Up to 16 partitions are supported, indexed from 1 to 16.
cfgVFlashPartitionEmulationType (Read or Write) Descripti on View or modify the emulation type for the partition. Legal Values String: Default None • • • HDD Floppy CD-DVD cfgVFlashPartitionFlashOSVolLabel (Read Only) Descripti on Displays the label for the partition that is visible to the operating system. Legal Values An alphanumeric string of up to six characters. Default None cfgVFlashPartitionFormatType (ReadOnly) Descripti on Displays the format type of the partition.
cfgVFlashPartitionAccessType (Read or Write) Descripti on Indicates the partition access permissions. It configures the access type to read-write. Legal Values • • Default 0 0 (ReadOnly) 1 (ReadWrite) cfgVFlashPartitionAttachState (Read or Write) Descripti on View or modify the partition to attached or detached. Legal Values • • Default 0 — Detached NOTE: Detaching the vFlashPartition by setting the cfgVFlashPartitionAttachState to 0 does not require a license.
Default 0 cfgRacSecurity For more information about generating certificate signing requests, see the subcommand sslcsrgen. For the country code, go to the link http://www.iso.org/iso/country_codes/ iso_3166_code_lists.htm The following sections provide information about the objects in the cfgRacSecurity group. cfgRacSecCsrCommonName (Read or Write) Descripti on Specifies the CSR Common Name (CN) that must be an IP or CMC name as given in the certificate. Legal Values A string of up to 254 characters.
Default cfgRacSecCsrLocalityName (Read or Write) Descripti on Specifies the CSR Locality (L). Legal Values A string of up to 254 characters. Default cfgRacSecCsrStateName (Read or Write) Descripti on Specifies the CSR State Name (S). Legal Values A string of up to 254 characters. Default cfgRacSecCsrCountryCode (Read/Write) Descripti on Specifies the CSR Country Code (CC). Legal Values A string of 2 alphabet country code.
Example racadm config -g cfgRacSecurity cfgRacSecCsrKeySize=1024 cfgRacSecCommonName= cfgRacSecOrganizationName= cfgRacSecOrganizationUnit= cfgRacSecLocalityName= cfgRacSecStateName= cfgRacSecCountryCode= cfgRacSecEmailAddr= cfgRacSecCsrKeySize (Read or Write) Descripti on Specifies the SSL asymmetric key size for the CSRs.
Database Objects With Get and Set Commands 4 This chapter provides the database groups and objects that must be used with the get or set subcommands. When using the objects, they must begin with FQDD or FQDD alias. The set operations for iDRAC, Lifecycle Controller and system objects do not require server restart. However, the set operations for NIC and BIOS objects are staged and job creation and server restart is required to apply and commit the pending values.
NOTE: • • • The staged configuration has the associated pending value in the output of the get operation, after it is configured successfully. The object values in the BIOS and NIC groups are case-sensitive. For NIC objects, the definition of the key format is: Key = ..—[]#GroupName” where, – Device Class: NIC – Locator: Integrated, Slot, Mezzanine or Embedded Example: • • • $racadm get NIC.NICConfig NIC.NICConfig.1 [Key=NIC.
• 2 — SGPIO Default Value 1 — I2C Write Privilege Configure iDRAC License Required iDRAC Express or iDRAC Enterprise Depende ncy None System.ChassisInfo The objects in this group are applicable only to modular chassis such as Dell PowerEdge M1000e. To obtain the chassis-specific information, use this group. System.ChassisInfo.Model (Read Only) Descripti on Indicates the LCD string the user modifies.
Default Value None Write Privilege Not Applicable License Required Not Applicable Depende ncy None System.ChassisInfo.ServiceTag (Read Only) Descripti on Provides the Service Tag of the chassis. Legal Values String of up to 62 ASCII characters Default Value None Write Privilege Not Applicable License Required Not Applicable Depende ncy None System.QuickSync The objects in this group manage the configuration and recovery of QuickSync settings. System.QuickSync.
Default Value 2 — Read-write Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Depende ncy To configure, the System.QuickSync.Presence property must indicate Present System.QuickSync.InactivityTimeout (Read or Write) Descripti on Configures the inactivity timer (in seconds) for Quick Sync.
Depende ncy To configure, the System.QuickSync.Presence property must indicate Present System.QuickSync.Presence (Read or Write) Descripti on Indicates the presence of Quick Sync feature in the server. Legal Values • 0— Not Supported • 1 — Absent • 2 — Present Default Value Not Applicable Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Depende ncy None System.LCD This group enables you to manage the front panel LCD user string settings.
• • • • • • • 8 — iDRAC MAC Address 16 — OS System Name 32 — Service Tag 64 — IPv6Address 128 — Ambient Temperature 256 — System Watts 512 — Asset Tag Default Value 32 — Service Tag Write Privilege Configure iDRAC and Configure User License Required iDRAC Express or iDRAC Enterprise Depende ncy None System.LCD.CurrentDisplay (Read Only) Descripti on The string currently displayed on the LCD.
NOTE: This property is deprecated from version 2.00.00.00. Use the System.LCD.UserDefinedString to perform the operation. Legal Values String of up to 62 ASCII characters Default Value 0 Write Privilege Not Applicable License Required Not Applicable Depende ncy Not Applicable System.LCD.UserDefinedString (Read or Write) Descripti on Indicates the LCD string set.
The following section provides information about the objects in the.Location group. System.Location.Aisle (Read or Write) Descripti on Indicates aisle where server is located. Legal Values String of up to 128 ASCII characters Default Value Not Applicable Write Privilege Configure iDRAC License Required iDRAC Express or iDRAC Enterprise Depende ncy None System.Location.DataCenter (Read or Write) Descripti on Indicates name of the data center where the system is located.
System.Location.DeviceSize (Read Only) Descripti on Indicates server chassis size. Legal Values Values: 1–255 Default Value Depends on the server form factor Write Privilege Not Applicable License Required iDRAC Express or iDRAC Enterprise Depende ncy None System.Location.Rack.Name (Read or Write) Descripti on Indicates rack where the system is located.
System.Location.Rack.Slot (Read or Write) Descripti on Indicates the slot where system is located. Legal Values Values: 1–255 Default Value 0 Write Privilege Configure iDRAC License Required iDRAC Express or iDRAC Enterprise Depende ncy None System.Location.RoomName (Read or Write) Descripti on Room name where the system is located.
System.Location.Chassis.Name (Read Only) Descripti on Indicates the chassis name. Legal Values String of up to 128 ASCII characters Default Value Not Applicable Write Privilege Not Applicable License Required iDRAC Express or iDRAC Enterprise Depende ncy None System.Location.Chassis.Slot (Read or Write) Descripti on Indicates chassis slot. Legal Values Values: 1–255 Default Value Not Applicable Write Privilege Configure iDRAC License Required Not Applicable Depende ncy None System.
The following section provides information about the objects in this group. NOTE: For Dell PowerEdge FM120x4 server with more than one iDRAC, the power is received and shared from CMC. Hence, the information about power and temperature for individual iDRACs are not displayed. System.Power.Status (Read Only) Descripti on Represents the device power state, either ON or OFF.
System.Power.Avg.LastDay (Read Only) Descripti on Indicates the average power value during the last day. Legal Values Values: 1–65535 Default Value Average power value during the last day. Write Privilege Not Applicable License Required iDRAC Express or iDRAC Enterprise Depende ncy None System.Power.Avg.LastHour (Read Only) Descripti on Displays the average power value during the last hour. Legal Values Values: 1–65535 Default Value Average power value during the last hour.
System.Power.Avg.LastWeek (Read Only) Descripti on Indicates the average power value during the last week. Legal Values Values: 1–65535 Default Value Average power value during the last week. Write Privilege Not Applicable License Required iDRAC Express or iDRAC Enterprise Depende ncy None System.Power.Cap.ActivePolicy.Btuhr (Read Only) Description Represents the active power in BTU/Hr a device is allowed to consume.
Default Value Not Applicable Write Privilege Not Applicable License Required iDRAC Express or iDRAC Enterprise Depende ncy None System.Power.Cap.ActivePolicy.Watts (Read Only) Descripti on Displays the Active Power Capacity in Watts Legal Values Values: 1–65535 Default Value Not Applicable Write Privilege Not Applicable License Required iDRAC Express or iDRAC Enterprise Depende ncy None System.Power.Cap.
License Required iDRAC Express or iDRAC Enterprise Depende ncy Enable System.Power.Cap.Enable System.Power.Cap. Enable (Read or Write) Descripti on Enables or disables user specified power budget threshold configuration. NOTE: This value is read only on Modular servers because CMC controls the capping. Legal Values • • 0 — Disabled 1 — Enabled Default Value 1 — Enabled Write Privilege Configure iDRAC License Required iDRAC Express or iDRAC Enterprise Depende ncy None System.Power.Cap.
Depende ncy None System.Power.Cap.MinThreshold (Read Only) Descripti on Because it is based on the current component inventory, it is the lowest calculated power consumption of the device. Legal Values Values: 1–65535 Default Value Not Applicable Write Privilege Not Applicable License Required iDRAC Express or iDRAC Enterprise Depende ncy None System.Power.Cap.Percent (Read or Write) Descripti on Represents the maximum power as a percentage of total power that a server is allowed to consume.
Depende ncy Enable System.Power.Cap.Enable System.Power.Redundancypolicy (Read or Write) Description Selects the redundancy policy. Legal Values • • • • N/A Not Redundant — In this mode, even if one PSU stops functioning, the server is automatically turned off. A/C Input Redundant — In this mode, the system is functional even if one PSU input circuit stops functioning, provided the PSUs are connected to different input circuits. This is also called AC redundancy.
Default Value Server power threshold in watts Write Privilege Configure iDRAC License Required iDRAC Express or iDRAC Enterprise Depende ncy Enable System.Power.Cap.Enable System.Power.EnergyConsumption (Read Only) Descripti on Represents the Cumulative power consumption by the blade or system. Legal Values Values: 1–65535 Default Value Cumulative power consumption Write Privilege Configure iDRAC License Required iDRAC Express or iDRAC Enterprise Depende ncy None System.Power.
License Required iDRAC Express or iDRAC Enterprise Depende ncy None System.Power.EnergyConsumption.StarttimeStamp (Read Only) Descripti on Displays the Timestamp of the cumulative power consumption. Legal Values String of up to 254 ASCII characters Default Value Timestamp of the cumulative power consumption. Write Privilege Not Applicable License Required iDRAC Express or iDRAC Enterprise Depende ncy None System.Power.Hotspare.
License Required iDRAC Express or iDRAC Enterprise Dependency None System.Power.Hotspare.PrimaryPSU (Read or Write) Descripti on Represents the primary PSU selection. Legal Values • • • • Default Value Not Applicable Write Privilege Configure iDRAC License Required iDRAC Express or iDRAC Enterprise Depende ncy None NOTE: This object is supported only for iDRAC on Rack and Tower servers. 1 — PSU1 2 — PSU2 5 — PSU1 and PSU3 10 — PSU2 and PSU4 System.Power.Max.
License Required iDRAC Express or iDRAC Enterprise Depende ncy None System.Power.Max.Amps.TimeStamp (Read Only) Descripti on Specifies the timestamp recorded for the Peak Power Consumption since this value was last cleared. Legal Values String up to 254 ASCII characters. Default Value Timestamp of the current peak power consumption Write Privilege Not Applicable License Required iDRAC Express or iDRAC Enterprise Depende ncy None System.Power.Max.
Depende ncy None System.Power.Max.LastDay (Read Only) Descripti on Displays the maximum power value during the last day. Legal Values Values: 1–65535 Default Value Maximum power value during the last day. Write Privilege Not Applicable License Required iDRAC Express or iDRAC Enterprise Depende ncy None System.Power.Max.LastDay.TimeStamp (Read Only) Descripti on Displays the timestamp of maximum power value during the last day.
System.Power.Max.LastHour (Read Only) Descripti on Displays the maximum power value during the last hour. Legal Values Values: 1–65535 Default Value Maximum power value during the last hour. Write Privilege Not Applicable License Required iDRAC Express or iDRAC Enterprise Depende ncy None System.Power.Max.LastHour.TimeStamp (Read Only) Descripti on Displays the timestamp of maximum power value during the last hour.
System.Power.Max.LastWeek (Read Only) Descripti on Displays the maximum power value during the last week. Legal Values Values: 1–65535 Default Value Maximum power value during the last week. Write Privilege Not Applicable License Required iDRAC Express or iDRAC Enterprise Depende ncy None System.Power.Max.LastWeek.TimeStamp (Read Only) Descripti on Displays the timestamp of maximum power value during the last week.
System.Power.Max. Power (Read Only) Descripti on The server consumes maximum power, because the last value was cleared. Legal Values Values: 1–65535 Default Value Peak power consumption of the server. Write Privilege Configure iDRAC License Required iDRAC Express or iDRAC Enterprise Depende ncy None System.Power.Max.Power.Timestamp (Read Only) Descripti on Displays time of maximum power consumption.
System.Power.Max.PowerClear (Read or Write) Descripti on Clears the Maximum Power Consumption timestamps. Legal Values 1 — Clear the Power Consumption Statistics Default Value Not Applicable Write Privilege Configure iDRAC License Required iDRAC Express or iDRAC Enterprise Depende ncy None System.Power.Min.LastDay (Read Only) Descripti on Displays the minimum power during the last day. Legal Values Values: 1–65535 Default Value Minimum power value during the last day.
System.Power.Min.LastDay.TimeStamp (Read Only) Descripti on Displays the minimum power value during the last day. Legal Values String of up to 254 ASCII characters Default Value Timestamp of the minimum power value during the last day. Write Privilege Configure iDRAC License Required iDRAC Express or iDRAC Enterprise Depende ncy None System.Power.Min.LastHour (Read Only) Descripti on Indicates the minimum power value during the last hour.
System.Power.Min.LastHour.Timestamp (Read Only) Descripti on Indicates the timestamp of minimum power during the last hour. Legal Values String of up to 254 ASCII characters Default Value Timestamp of the minimum power value during the last hour. Write Privilege Not Applicable License Required iDRAC Express or iDRAC Enterprise Depende ncy None System.Power.Min.LastWeek (Read Only) Descripti on Indicates the minimum power during the last week.
Default Value Timestamp of the minimum power value during the last week. Write Privilege Not Applicable License Required iDRAC Express or iDRAC Enterprise Depende ncy None System.Power.PCIeAllocation (Read or Write) Descripti on Specifies PCIe power allocation for blade servers. It is applicable only for PowerEdge M610x. NOTE: This object only applies to servers that support PCIe Card.
NOTE: • • This object is supported only for iDRAC on Rack and Tower servers. This object is applicable only if System.Power.Cap.Enable is set to 1. Legal Values • • 0 — Disabled 1 — Enabled Default Value 0 — Disabled Write Privilege Configure iDRAC License Required iDRAC Express or iDRAC Enterprise None Depende ncy System.Power.RedundancyCapabilities (Read Only) Descripti on Returns the redundancy capabilities in the form of a bitmask.
Write Privilege Not Applicable License Required Not Applicable Depende ncy Not Applicable System.Power.RedundantState (Read Only) Descripti on Retrieves the redundancy state for the chassis. Legal Values • • Default 0 — None Write Privilege Not Applicable License Required Not Applicable Depende ncy Not Applicable NOTE: This object is not applicable for Rack and Tower server. 0 — None 1 — Full System.Power.Supply This group provides information relating to the Power Supplies.
System.Power.Supply.CurrentDraw (Read Only) Descripti on Displays the instantaneous current consumption in 0.1 amps. Legal Values String of up to 254 ASCII characters Default Value Not Applicable Write Privilege Not Applicable License Required iDRAC Express or iDRAC Enterprise Depende ncy None System.Power.Supply.FwVer (Read Only) Descripti on Displays the firmware version of the PSU. Legal Values String up to 254 ASCII characters.
System.Power.Supply.[i].MaxInputPower (Read Only) Descripti on Displays the AC input rated power in Watts. Legal Values Integer > 0 Default Value 0 Write Privilege Not Applicable License Required Not Applicable Depende ncy Not Applicable System.Power.Supply.[i].MaxOutputPower (Read Only) Descripti on Displays the DC output rated power in Watts.
System.Power.Supply.[i].Status (Read Only) Descripti on Displays the status of the PSU. Legal Values • • • • Default 0 — absent Write Privilege Not Applicable License Required Not Applicable Depende ncy Not Applicable 0 — absent 1 — present and OK 2 — failure 3 — predictive failure System.Power.Supply.[i].Type (Read Only) Descripti on Displays whether the power supply is AC or DC.
System.Power.Supply.[i].LineStatus (Read Only) Descripti on Specifies if this power supply is powered off or on. Legal Values Integer > 0 Default None Write Privilege Not Applicable License Required Not Applicable Depende ncy Not Applicable System.Power.Supply.[i].PMBusMonitoring (Read Only) Descripti on Specifies if this PMBus is present or not. Legal Values Integer > 0 Default 0 Write Privilege Not Applicable License Required Not Applicable Depende ncy Not Applicable System.
System.ServerOS.HostName (Read or Write) Descripti on Displays the host name of the managed server. Legal Values String of up to 256 ASCII characters Default Value Not Applicable Write Privilege Configure iDRAC License Required iDRAC Express or iDRAC Enterprise Depende ncy None System.ServerOS.OSName (Read or Write) Descripti on Displays the operating system name of the managed server.
Default Value Not Applicable Write Privilege Not Applicable License Required iDRAC Express or iDRAC Enterprise Depende ncy None System.ServerOS.ServerPoweredOnTime (Read Only) Descripti on Indicates the time (in seconds) from when the operating system is turned ON. Legal Values Any integer value indicating the system powered on time duration. Default Value 0 Write Privilege Configure iDRAC License Required iDRAC Express or iDRAC Enterprise Depende ncy None System.
NOTE: This attribute is platform dependent. Legal Values • • • • • Default value 255 — None License Required iDRAC Express or iDRAC Enterprise Depende ncy None 0 — 40°C 1 —45°C 2 — 50°C 3 — 55°C 255 — None System.ThermalSettings.BaseAlgorithm (Read or Write) Descripti on Specifies the thermal base algorithm. Legal Values • • • Default values None License Required iDRAC Express Depende ncy None NOTE: This object is not applicable for Rack and Tower server.
NOTE: This attribute is platform dependent. Legal Values MFSMinimumLimit — MFSMaximumLimit Default Value 0 Write Privilege Not Applicable License Required iDRAC Express or iDRAC Enterprise Depende ncy None System.ThermalSettings.FanSpeedOffset (Read or Write) Descripti on Specifies the fan speed offset. Legal Values • • • Default value OFF License Required iDRAC Express or iDRAC Enterprise Depende ncy None NOTE: This attribute is platform dependent.
Default Value 0 License Required iDRAC Express or iDRAC Enterprise Depende ncy None System.ThermalSettings.FanSpeedMediumOffsetVal (Read Only) Descripti on Indicates the percentage range for medium fan speed offset. Legal Values Integral Values: 0 – 100 Default Value 0 License Required iDRAC Express or iDRAC Enterprise Depende ncy None NOTE: This attribute is platform dependent. System.ThermalSettings.
System.ThermalSettings.FanSpeedMaxOffsetVal (Read Only) Descripti on Indicates the percentage range for low fan offset speed. Legal Values Integral Values: 0 – 100 Default Value 0 License Required iDRAC Express or iDRAC Enterprise Depende ncy None NOTE: This attribute is platform dependent. System.ThermalSettings.MFSMinimumLimit (Read Only) Descripti on Indicates the minimum limit for MFS.
Default Value 255 License Required iDRAC Express or iDRAC Enterprise Depende ncy None System.ThermalSettings.ThermalProfile (Read or Write) Descripti on Sets the thermal base algorithm. Legal Values • 0 — Default Thermal Profile Settings • 1 — Maximum performance • 2 — Minimum Power Default Value Auto Write Privilege Configure iDRAC License Required iDRAC Express or iDRAC Enterprise Depende ncy None System.ThermalConfig The objects in this group manage the thermal configuration.
Write Privilege Configure iDRAC License Required iDRAC Express or iDRAC Enterprise Depende ncy None System.ThermalConfig.EventGenerationInterval (Read or Write) Descripti on Indicates the time interval (in days) for warning events to be generated. Legal Values Integral Values: 0-365 Default Value 30 Write Privilege Configure iDRAC License Required iDRAC Express or iDRAC Enterprise Depende ncy None System.ThermalConfig.
LifecycleController.LCAttributes The following section provides information about the objects in the LifecycleController.LCAttributes group. NOTE: A job successfully configured using the autoupdate or autobackup feature settings can be deleted only if the job is currently not running or downloading. LifecycleController.LCAttributes.autobackup (Read or Write) Descripti on Enables or disables the automatic backup scheduler.
Dependen cy None LifecycleController.LCAttributes.autoupdate (Read or Write) Descripti on Enables or disables the automatic update scheduler. Legal Values • • Default Value 1 — Enabled Write Privilege Server Control License Required iDRAC Enterprise Depende ncy None 0 — Disabled 1 — Enabled LifecycleController.LCAttributes.BiosRTDRequested (Read or Write) Description Allows to reset all the BIOS attributes to the default state.
LifecycleController.LCAttributes.CollectSystemInventor yOnRestart (Read or Write) Descripti on Enables or disables collection of system inventory on host reboot. Legal Values • • Default Value 1 — Enabled Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Depende ncy None 0 — Disabled 1 — Enabled LifecycleController.LCAttributes.DiscoveryFactoryDefaul ts (Read Only) Descriptio n Enables or disables the discovery factory defaults.
LifecycleController.LCAttributes.IPChangeNotifyPS (Read or Write) Description Notifies the provisioning server about the change in IP address. Legal Values • 0 — Off • 1 — On Default Value 0 — Off Write Privilege Configure iDRAC License Required iDRAC Enterprise Dependency None LifecycleController.LCAttributes.Licensed (Read Only) Descriptio n Indicates whether or not the part replacement feature is licensed.
• 2 — Recovery (Read Only Value) Default Value 1 — Enabled Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Depende ncy None LifecycleController.LCAttributes.ProvisioningServer (Read or Write) Description Specifies the Provisioning Server Address. Legal Values String of up to 255 ACSII characters Default Value Not Applicable Write Privilege Configure iDRAC License Required iDRAC Enterprise Dependency None LifecycleController.LCAttributes.
License Required iDRAC Express or iDRAC Enterprise Depende ncy None LifecycleController.LCAttributes.PartFirmwareUpdate (Read or Write) Descripti on Apply firmware changes to the replaced part on part replacement. Legal Values 0 — Disabled 1 — Allow version upgrade only 2 — Match firmware of replaced part Default Value 2 — Match firmware of replaced part Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Depende ncy None LifecycleController.LCAttributes.
Dependen cy None LifecycleController.LCAttributes.VirtualAddressManage mentApplication (Read or Write) Description Specifies the console name of Virtual Address Management Application. Legal Values String of up to 32 ACSII characters Default Value Not Applicable Write Privilege Configure iDRAC License Required iDRAC Enterprise Dependency None iDRAC.ActiveDirectory To manage the configuration of the iDRAC Active Directory features, use the objects in this group. iDRAC.ActiveDirectory.
iDRAC.ActiveDirectory.CertValidationEnable (Read or Write) Descripti on Enables or disables Active Directory certificate validation as a part of the Active Directory configuration process. Legal Values • • Default Value Not Applicable Write Privilege Configure iDRAC License Required iDRAC Enterprise Depende ncy None 0 — Disabled 1 — Enabled iDRAC.ActiveDirectory.DCLookupByUserDomain (Read or Write) Descripti on To look up the user domain for Active Directory, enables the selection option.
iDRAC.ActiveDirectory.DCLookupDomainName (Read or Write) Descripti on The configured search domain is used when DCLookupByUserDomain is disabled. Legal Values String of up to 254 ASCII characters Default Value Not Applicable Write Privilege Configure iDRAC License Required iDRAC Enterprise Depende ncy None iDRAC.ActiveDirectory.
iDRAC.ActiveDirectory.DomainController1 (Read or Write) Descripti on FQDN that stores the address of the active directory domain controller1. Legal Values String of up to 254 ASCII characters Default Value Not Applicable Write Privilege Configure iDRAC License Required iDRAC Enterprise Depende ncy None iDRAC.ActiveDirectory.
iDRAC.ActiveDirectory.DomainController3 (Read or Write) Descripti on FQDN that stores the address of the active directory domain controller 3 Legal Values String of up to 254 ASCII characters Default Value Not Applicable Write Privilege Configure iDRAC License Required iDRAC Enterprise Depende ncy None iDRAC.ActiveDirectory.Enable (Read or Write) Descripti on Enables or disables Active Directory user authentication on iDRAC.
iDRAC.ActiveDirectory.GCLookupEnable (Read or Write) Descripti on Determines how to look up the global catalog server. Legal Values • • Default Value 0 — Disabled Write Privilege Configure iDRAC License Required iDRAC Enterprise Depende ncy Cannot be enabled unless one of the following is configured: • IPv4.DNS1 • IPv4.DNS2 • IPv6.DNS1 • IPv6.DNS2 0 — Disabled 1 — Enabled iDRAC.ActiveDirectory.
iDRAC.ActiveDirectory.GlobalCatalog1 (Read or Write) Descripti on Specifies the Global Catalog server from which you want the iDRAC to obtain user names. Legal Values String of up to 254 ASCII characters Default Value Not Applicable Write Privilege Configure iDRAC License Required iDRAC Enterprise Depende ncy None iDRAC.ActiveDirectory.GlobalCatalog2 (Read or Write) Descripti on To obtain user names, specifies the Global Catalog server from which you want the iDRAC.
iDRAC.ActiveDirectory.GlobalCatalog3 (Read or Write) Descripti on To obtain user names, specifies the Global Catalog server from which you want the iDRAC. Legal Values String of up to 254 ASCII characters Default Value Not Applicable Configure iDRAC Write Privilege License Required iDRAC Enterprise Depende ncy None iDRAC.ActiveDirectory.RacDomain (Read or Write) Description Active Directory Domain in which iDRAC resides.
Default Value Not Applicable Write Privilege Configure iDRAC License Required iDRAC Enterprise Depende ncy None iDRAC.ActiveDirectory.Schema (Read or Write) Descripti on To use with Active Directory, determine the schema type. Legal Values • • Default Value 1 — Extended Schema Write Privilege Configure iDRAC License Required iDRAC Enterprise Depende ncy None 1 — Extended Schema 2 — Standard Schema iDRAC.ActiveDirectory.
Write Privilege Configure iDRAC License Required iDRAC Enterprise Depende ncy Cannot be enabled unless SmartCard Logon Enable is disabled. iDRAC.ADGroup To manage the configuration of AD standard schema settings, use these objects in the group. This group is indexed from 1 to 5. iDRAC.ADGroup.Domain (Read or Write) Descripti on Active Directory Domain in which the Role Group resides.
Configure iDRAC Write Privilege License Required iDRAC Enterprise Depende ncy None iDRAC.ADGroup.Privilege (Read or Write) Descripti on Role-based authority privileges for a Role Group. Legal Values Integral values: 0–511 (0x1FF) Default Value 0 Write Privilege Configure iDRAC License Required iDRAC Enterprise Depende ncy None iDRAC.AutoOSLock To manage the OS Auto lock feature, use these objects in this group. iDRAC.AutoOSLock.
Write Privilege Configure iDRAC License Required iDRAC Express or iDRAC Enterprise Depende ncy None iDRAC.EmailAlert The objects in this group configure email alerting capabilities. This group is indexed from 1 to 4. iDRAC.EmailAlert.Address (Read or Write) Descripti on Specifies the destination email address for email alerts.
Write Privilege Configure iDRAC License Required iDRAC Express or iDRAC Enterprise Depende ncy None iDRAC.EmailAlert.Enable (Read or Write) Descripti on To receive alerts, enable or disable the destination. Legal Values • • Default Value 0 — Disabled Write Privilege Configure iDRAC License Required iDRAC Express or iDRAC Enterprise Depende ncy None 0 — Disabled 1 — Enabled iDRAC.Info To manage information about iDRAC being queried, use these objects in the group. iDRAC.Info.
Write Privilege Configure iDRAC License Required iDRAC Express or iDRAC Enterprise Depende ncy None iDRAC.Info.Description (Read or Write) Descripti on Text description of the iDRAC. Legal Values String of up to 255 ASCII characters Default Value The system component provides a set of remote management operations for Dell PowerEdge Servers. Write Privilege Configure iDRAC License Required iDRAC Express or iDRAC Enterprise Depende ncy None iDRAC.Info.
Depende ncy None iDRAC.Info.Product (Read or Write) Descripti on String identifying the Product. Legal Values String of up to 63 ASCII characters Default Value Integrated Dell Remote Access Controller Write Privilege Configure iDRAC License Required iDRAC Express or iDRAC Enterprise Depende ncy None iDRAC.Info.
iDRAC.Info.Version (Read Only) Descripti on String containing the current product firmware version. Legal Values String of up to 63 ASCII characters Default Value Not Applicable Write Privilege Configure iDRAC License Required iDRAC Express or iDRAC Enterprise Depende ncy None iDRAC.Info.ServerGen (Read or Write) Descripti on Indicates the server generation.
iDRAC.IOIDOptEnable (Read or Write) Descripti on Enables or disables Identity Optimization (IO). Legal Values • • Default values 0 — Disabled Write Privilege Configure iDRAC License Required iDRAC Express or iDRAC Enterprise Depende ncy None 0 — Disabled 1 — Enabled iDRAC.IOIDOpt.InitiatorPersistencePolicy (Read or Write) Descripti on Sets the virtual address management .
Depende ncy IOIDOptEnable attribute must be enabled. iDRAC.IOIDOpt.StorageTargetPersistencePolicy (Read or Write) Descripti on Sets the Virtual Address Management StorageTargetPersistencePolicy.
• 6 — PowerGoodReset, ACPowerLoss • 7 — WarmReset, PowerGoodReset, ACPowerLoss Default Value ACPowerLoss, PowerGoodReset, WarmReset Write Privilege Configure iDRAC License Required iDRAC Express or iDRAC Enterprise Depende ncy To configure, the iDRAC.IOIDOpt.Enable property must indicate Enabled. iDRAC.IOIDOpt.VirtualAddressPersistencePolicyNonAux Pwrd (Read or Write) Descripti on Applied for the Non-Aux powered devices, which persist the virtual address on warm reset.
iDRAC.IPBlocking To configure IP address blocking feature of iDRAC, Use the objects in this group. iDRAC.IPBlocking.BlockEnable (Read or Write) Descripti on Enables or disables the IPv4 address blocking feature of iDRAC. Legal Values • • Default Value 1 — Enabled Write Privilege Configure iDRAC License Required iDRAC Express or iDRAC Enterprise Depende ncy None 0 — Disabled 1 — Enabled iDRAC.IPBlocking.
Depende ncy None iDRAC.IPBlocking.FailWindow (Read or Write) Descripti on Defines the time span in seconds that the unsuccessful attempts are counted. Legal Values Integral values from 10 to 65535 Default Value 60 Write Privilege Configure iDRAC License Required iDRAC Express or iDRAC Enterprise Depende ncy None iDRAC.IPBlocking.PenaltyTime (Read or Write) Descripti on Defines the time span in seconds that session requests from an IP address with excessive failures are rejected.
iDRAC.IPBlocking.RangeAddr (Read or Write) Descripti on Specifies the acceptable IPv4 address bit pattern in positions determined by the 1s in the range mask. Legal Values Valid IPv4 Address Default Value 192.168.1.1 Write Privilege Configure iDRAC License Required iDRAC Express or iDRAC Enterprise Depende ncy None iDRAC.IPBlocking.RangeEnable (Read or Write) Descripti on Enables or disables the IPv4 Address Range validation feature of iDRAC.
iDRAC.IPBlocking.RangeMask (Read or Write) Descripti on Standard IP mask values with left-justified bits. Legal Values Valid IPv4 Address Mask Default Value 255.255.255.0 Write Privilege Configure iDRAC License Required iDRAC Express or iDRAC Enterprise Depende ncy None iDRAC.IPMILan To configure IPMI over LAN of the system, use the objects in this group. iDRAC.IPMILan.AlertEnable (Read or Write) Descriptio Enables or disables global email alerting.
Depende ncy None iDRAC.IPMILan.CommunityName (Read or Write) Descripti on Specifies the SNMP community name for traps. Legal Values String of up to 18 ASCII characters Default Value Public Write Privilege Configure iDRAC License Required iDRAC Express or iDRAC Enterprise Depende ncy None iDRAC.IPMILan.Enable (Read or Write) Descripti on Enables or disables the IPMI over LAN interface.
iDRAC.IPMILan.EncryptionKey (Read or Write) Descripti on Enables or disables the IPMI over LAN interface. Legal Values String of up to 18 ASCII characters Default Value 0000000000000000000000000000000000000000 Write Privilege Configure iDRAC License Required iDRAC Express or iDRAC Enterprise Depende ncy None iDRAC.IPMILan.PrivLimit (Read or Write) Descripti on Specifies the maximum privilege level for IPMI over LAN access.
iDRAC.IPMISerial To configure the IPMI serial interface, use this objects in this group. NOTE: This is supported only for rack and tower systems. iDRAC.IPMISerial.BaudRate (Read or Write) Descripti on Specifies the baud rate for serial connection over IPMI. Legal Values • • • • • Default Value 115200 Write Privilege Configure iDRAC License Required iDRAC Express or iDRAC Enterprise Depende ncy None 9600 19200 38400 57600 115200 iDRAC.IPMISerial.
Write Privilege Configure iDRAC License Required iDRAC Express or iDRAC Enterprise Depende ncy None iDRAC.IPMISerial.ConnectionMode (Read or Write) Descripti on Determines the IPMI defined mode of the serial port. Legal Values • • Default Value 1 — Basic Write Privilege Configure iDRAC License Required iDRAC Express or iDRAC Enterprise Depende ncy None 1 — Basic 0 — Terminal iDRAC.IPMISerial.
Depende ncy None iDRAC.IPMISerial.EchoControl (Read or Write) Descripti on Enables or disables echo control on the IPMI serial interface. Legal Values • • Default Value 1 — Enabled Write Privilege Configure iDRAC License Required iDRAC Express or iDRAC Enterprise Depende ncy None 0 — Disabled 1 — Enabled iDRAC.IPMISerial.FlowControl (Read or Write) Descripti on Specifies the Flow Control setting for IPMI serial port.
iDRAC.IPMISerial.HandshakeControl (Read or Write) Descripti on Enables or disables the IPMI terminal mode handshake control. Legal Values • • Default Value 1 — Enabled Write Privilege Configure iDRAC License Required iDRAC Express or iDRAC Enterprise Depende ncy None 0 — Disabled 1 — Enabled iDRAC.IPMISerial.InputNewLineSeq (Read or Write) Descripti on Specifies the input new line sequence for the IPMI serial interface.
iDRAC.IPMISerial.LineEdit (Read or Write) Descripti on Enables or disables line editing on the IPMI serial interface. Legal Values • • Default Value 1 — Enabled Write Privilege Configure iDRAC License Required iDRAC Express or iDRAC Enterprise Depende ncy None 0 — Disabled 1 — Enabled iDRAC.IPMISerial.NewLineSeq (Read or Write) Descripti on Specifies the new line sequence for the IPMI serial interface.
iDRAC.IPMISOL Use the objects in this group to configure the SOL capabilities of the system. iDRAC.IPMISOL.AccumulateInterval (Read or Write) Descripti on Specifies the typical amount of time that iDRAC waits before transmitting a partial SOL character data packet. Legal Values Integral values: 1–255 Default Value Not Applicable Write Privilege Configure iDRAC License Required iDRAC Express or iDRAC Enterprise Depende ncy None iDRAC.IPMISOL.
Depende ncy None iDRAC.IPMISOL.Enable (Read or Write) Descripti on Enables or disables SOL. Legal Values • • Default Value 1 — Enabled Write Privilege Configure iDRAC License Required iDRAC Express or iDRAC Enterprise Depende ncy None 0 — Disabled 1 — Enabled iDRAC.IPMISOL.MinPrivilege (Read or Write) Descriptio Specifies the minimum privilege level required for serial access.
iDRAC.IPMISOL.SendThreshold (Read or Write) Descripti on To buffer before sending an SOL data packet, specifies the SOL threshold limit value and the maximum number of bytes Legal Values Integral values: 1–255 Default Value Not Applicable Write Privilege Configure iDRAC License Required iDRAC Express or iDRAC Enterprise Depende ncy None iDRAC.IPv4 To manage the IPv4 configuration properties of iDRAC, use these objects in this group. iDRAC.IPv4.
Depende ncy Cannot be set unless IPv4.DHCPEnable is disabled. iDRAC.IPv4.DHCPEnable (Read or Write) Descripti on Specifies if DHCP is used to assign the iDRAC IPv4 address. Legal Values • • Default Value 0 — Disabled Write Privilege Configure iDRAC License Required iDRAC Express or iDRAC Enterprise Depende ncy Cannot be enabled unless IPv4.Enable is enabled. 0 — Disabled 1 — Enabled iDRAC.IPv4.DNS1 (Read or Write) Descripti on IPv4 address for DNS server 1.
iDRAC.IPv4.DNS2 (Read or Write) Descripti on IPv4 address for DNS Server 2. Legal Values Valid IPv4 Address Default Value 0.0.0.0 Write Privilege Configure iDRAC License Required iDRAC Express or iDRAC Enterprise Depende ncy Cannot be set unless IPv4.DNSFromDHCP is disabled. iDRAC.IPv4.DNSFromDHCP (Read or Write) Descripti on Specifies if the DNS server IPv4 addresses must be assigned from the DHCP server on the network.
iDRAC.IPv4.Enable (Read or Write) Descripti on Enables or disables the iDRAC IPv4 stack. Legal Values • • Default Value 1 — Enabled Write Privilege Configure iDRAC License Required iDRAC Express or iDRAC Enterprise Depende ncy None 0 — Disabled 1 — Enabled iDRAC.IPv4.Gateway (Read or Write) Descripti on The gateway for the iDRAC IPv4 address. Legal Values Valid IPv4 gateway Default Value 192.168.0.
iDRAC.IPv4.Netmask (Read or Write) Descripti on The subnet mask used for the iDRAC IPv4 address. Legal Values Valid IPv4 netmask Default Value 255.255.255.0 Write Privilege Configure iDRAC License Required iDRAC Express or iDRAC Enterprise Depende ncy Cannot be set unless IPv4.DHCPEnable is disabled. iDRAC.IPv4Static Use the objects in this group to manage the IPv4 Static configuration properties of iDRAC. iDRAC.IPv4Static.Address (Read or Write) Descripti on iDRAC static IPv4 address.
iDRAC.IPv4Static.DNS1 (Read or Write) Descripti on Statically configurable DNS Server 1. Legal Values Valid IPv4 Address Default Value 0.0.0.0 Write Privilege Configure iDRAC License Required iDRAC Express or iDRAC Enterprise Depende ncy None iDRAC.IPv4Static.DNS2 (Read or Write) Descripti on Statically configurable DNS Server 2. Legal Values Valid IPv4 Address Default Value 0.0.0.
iDRAC.IPv4Static.DNSFromDHCP (Read or Write) Descriptio n Specifies if the DNS server IPv4 addresses should be assigned from the DHCP server on the network. Legal Values • 0 — Disabled • 1 — Enabled Default Value 0 — Disabled Write Privilege Configure iDRAC License Required iDRAC Express or iDRAC Enterprise Dependen cy None iDRAC.IPv4Static.Gateway (Read or Write) Descripti on iDRAC static IPv4 gateway. This address can be configured even when DHCP is enabled.
iDRAC.IPv4Static.Netmask (Read or Write) Descripti on iDRAC static IPv4 subnet mask. This address can be configured even when DHCP is enabled. Legal Values Valid IPv4 netmask Default Value 255.255.255.0 Write Privilege Configure iDRAC License Required iDRAC Express or iDRAC Enterprise Depende ncy None iDRAC.IPv6 To manage the IPv6 configuration properties of iDRAC, use the objects in this group. iDRAC.IPv6.Address 1 (Read or Write) Descripti on iDRAC IPv6 Address.
iDRAC.IPv6.Address 2 (Read or Write) Descripti on iDRAC IPv6 second address. Legal Values Valid IPv6 Address Default Value :: Write Privilege Configure iDRAC License Required iDRAC Express or iDRAC Enterprise Depende ncy None iDRAC.IPv6.Address 3 (Read or Write) Descripti on iDRAC IPv6 third address.
iDRAC.IPv6.Address 4 (Read or Write) Descripti on iDRAC IPv6 fourth address. Legal Values Valid IPv6 Address Default Value :: Write Privilege Configure iDRAC License Required iDRAC Express or iDRAC Enterprise Depende ncy None iDRAC.IPv6.Address 5 (Read or Write) Descripti on iDRAC IPv6 fifth address.
iDRAC.IPv6.Address 6 (Read or Write) Descripti on iDRAC IPv6 sixth address. Legal Values Valid IPv6 Address Default Value :: Write Privilege Configure iDRAC License Required iDRAC Express or iDRAC Enterprise Depende ncy None iDRAC.IPv6.Address 7 (Read or Write) Descripti on iDRAC IPv6 seventh address.
iDRAC.IPv6.Address 8 (Read or Write) Descripti on iDRAC IPv6 eighth address. Legal Values Valid IPv6 Address Default Value :: Write Privilege Configure iDRAC License Required iDRAC Express or iDRAC Enterprise Depende ncy None iDRAC.IPv6.Address 9 (Read or Write) Descripti on iDRAC IPv6 ninth address.
iDRAC.IPv6.Address10 (Read or Write) Descripti on iDRAC IPv6 tenth address. Legal Values Valid IPv6 Address Default Value :: Write Privilege Configure iDRAC License Required iDRAC Express or iDRAC Enterprise Depende ncy None iDRAC.IPv6.Address11 (Read or Write) Descripti on iDRAC IPv6 eleventh address.
iDRAC.IPv6.Address12 (Read or Write) Descripti on iDRAC IPv6 twelfth address. Legal Values Valid IPv6 Address Default Value :: Write Privilege Configure iDRAC License Required iDRAC Express or iDRAC Enterprise Depende ncy None iDRAC.IPv6.Address13 (Read or Write) Descripti on iDRAC IPv6 thirteenth address.
iDRAC.IPv6.Address14 (Read or Write) Descripti on iDRAC IPv6 fourteenth address. Legal Values Valid IPv6 Address Default Value :: Write Privilege Configure iDRAC License Required iDRAC Express or iDRAC Enterprise Depende ncy None iDRAC.IPv6.Address15 (Read or Write) Descripti on iDRAC IPv6 fifteenth address.
iDRAC.IPv6.AutoConfig (Read or Write) Descripti on Enables or disables the iDRAC IPv6 auto configuration option. Legal Values • • Default Value 1 — Enabled Write Privilege Configure iDRAC License Required iDRAC Express or iDRAC Enterprise Depende ncy None 0 — Disabled 1 — Enabled iDRAC.IPv6.DNS1 (Read or Write) Descripti on IPv6 DNS Server 1 Address.
iDRAC.IPv6.DNS2 (Read or Write) Descripti on IPv6 DNS Server 2 Address. Legal Values Valid IPv6 Address Default Value :: Write Privilege Configure iDRAC License Required iDRAC Express or iDRAC Enterprise Depende ncy Cannot be set unless IPv6.DNSFromDHCP6 is disabled. iDRAC.IPv6.DNSFromDHCP6 (Read or Write) Descripti on Specifies if the DNS Server addresses are obtained from DHCP or not.
iDRAC.IPv6.Enable (Read or Write) Descripti on Enables or Disables iDRAC IPv6 stack. Legal Values • • Default Value 0 — Disabled Write Privilege Configure iDRAC License Required iDRAC Express or iDRAC Enterprise Depende ncy None 0 — Disabled 1 — Enabled iDRAC.IPv6.
iDRAC.IPv6.LinkLocalAddress (Read or Write) Descripti on iDRAC IPv6 Link Local Address. Legal Values Valid IPv6 Address Default Value :: Write Privilege Configure iDRAC License Required iDRAC Express or iDRAC Enterprise Depende ncy None iDRAC.IPv6.PrefixLength (Read or Write) Descripti on Prefix length for the iDRAC IPv6 Address.
iDRAC.IPv6Static To manage the IPv6 static configuration properties of iDRAC, use the objects in this group iDRAC.IPv6Static.Address1 (Read or Write) Descripti on iDRAC static IPv6 address. Legal Values Valid IPv6 Address Write Privilege Configure iDRAC License Required iDRAC Express or iDRAC Enterprise Depende ncy None iDRAC.IPv6Static.DNS1 (Read or Write) Descripti on Statically configurable DNS Server 1.
iDRAC.IPv6Static.DNS2 (Read or Write) Descripti on Statically configurable DNS Server 2. Legal Values Valid IPv6 Address Write Privilege Configure iDRAC License Required iDRAC Express or iDRAC Enterprise Depende ncy None iDRAC.IPv6Static.DNSFromDHCP6 (Read or Write) Descripti on Specifies if the DNS server IPv6 addresses must be assigned from the DHCP server on the network.
Write Privilege Configure iDRAC License Required iDRAC Express or iDRAC Enterprise Depende ncy None iDRAC.IPv6Static.PrefixLength (Read or Write) Descripti on Prefix length for the iDRAC IPv6 Address. Legal Values Integral values: 1–128 Default Value 64 Write Privilege Configure iDRAC License Required iDRAC Express or iDRAC Enterprise Depende ncy None iDRAC.IPv6URL Use the objects in this group to manage the IPv6 static configuration properties of iDRAC. iDRAC.IPv6URL.
License Required iDRAC Express or iDRAC Enterprise Dependency iDRAC IPv6 has to be Enabled iDRAC.LDAP To configure properties for LDAP settings, use the objects in this group. iDRAC.LDAP.BaseDN (Read or Write) Descripti on The Domain Name of the branch of the directory where all searches must start. Legal Values String of up to 63 ASCII characters Default Value Not Applicable Write Privilege Configure iDRAC License Required iDRAC Enterprise Depende ncy None iDRAC.LDAP.
License Required iDRAC Enterprise Depende ncy None iDRAC.LDAP.BindPassword (Write Only) Description A bind password to use along with the bindDN. Legal Values String of up to 254 ASCII characters Default Value Not Applicable Write Privilege Configure iDRAC License Required iDRAC Enterprise Dependency None iDRAC.LDAP.CertValidationEnable (Read or Write) Descripti on Controls certificate validation during SSL handshake.
iDRAC.LDAP.Enable (Read or Write) Descripti on Turns LDAP service on or off. Legal Values • • Default Value Not Applicable Write Privilege Configure iDRAC License Required iDRAC Enterprise Depende ncy None 0 — Disabled 1 — Enabled iDRAC.LDAP.GroupAttribute (Read or Write) Descripti on Specifies which LDAP attribute is used to check for group membership.
iDRAC.LDAP.GroupAttributeIsDN (Read or Write) Descripti on Specifies whether the user domain name must be used from the LDAP server or from the user that provides login. Legal Values String of up to 128 ASCII characters Default Value 1 — Enabled Write Privilege Configure iDRAC License Required iDRAC Enterprise Depende ncy None iDRAC.LDAP.Port (Read or Write) Descripti on Port of LDAP over SSL.
iDRAC.LDAP.SearchFilter (Read or Write) Descripti on A valid LDAP search filter to be used if the user attribute cannot uniquely identify the login user within the chosen baseDN. Legal Values String of up to 254 ASCII characters Default Value Not Applicable Write Privilege Configure iDRAC License Required iDRAC Enterprise Depende ncy None iDRAC.LDAP.Server (Read or Write) Descripti on Configures the address of the LDAP Server.
iDRAC.LDAP.UserAttribute (Read or Write) Descripti on To search, specify the user attribute. Legal Values String of up to 128 ASCII characters Default Value Not Applicable Write Privilege Configure iDRAC License Required iDRAC Enterprise Depende ncy None iDRAC.LDAPRoleGroup The objects in this group enable configuration of role groups for LDAP. This group is indexed from 1 to 5. iDRAC.LDAPRoleGroup.DN (Read or Write) Descripti on The Domain Name of this group.
iDRAC.LDAPRoleGroup.Privilege (Read or Write) Descripti on A bit-mask defining the privileges associated with this particular group. Legal Values Integral values: 0–511 (0x1FF) Default Value 0 Write Privilege Configure iDRAC License Required iDRAC Enterprise Depende ncy None iDRAC.LocalSecurity To manage the ability to configure iDRAC, use the objects in this group. iDRAC.LocalSecurity.
iDRAC.LocalSecurity.PrebootConfig (Read or Write) Descripti on To configure iDRAC from the BIOS POST option-ROM, enable or disable the ability of the local user. Legal Values • • Default Value 0 — Disabled Write Privilege Configure iDRAC License Required iDRAC Express or iDRAC Enterprise Depende ncy None 0 — Disabled 1 — Enabled iDRAC.Logging iDRAC. Logging Manages the ability to configure iDRAC iDRAC.Logging.
Depende ncy None iDRAC.NIC To configure the iDRAC NIC, use the object in this group. iDRAC.NIC.Autoconfig (Read or Write) Descripti on Sets the DHCP auto configuration operation. Legal Values • 0 — Disabled NOTE: • iDRAC does not perform DHCP configuration. 1 — Enable Once NOTE: • iDRAC performs DHCP configuration once. 2 — Enable Once After Reset NOTE: Configures after iDRAC reset.
iDRAC.NIC.AutoDetect (Read or Write) Descripti on Enables or disables auto detection feature of iDRAC. Legal Values • • Default Value 0 — Disabled Write Privilege Configure iDRAC License Required iDRAC Express or iDRAC Enterprise Depende ncy This object is writable only when NIC Selection is in shared mode. 0 — Disabled 1 — Enabled iDRAC.NIC.Autoneg (Read or Write) Descripti on Enables autonegotiation of physical link speed and duplex.
iDRAC.NIC.DedicatedNICScanTime (Read or Write) Descripti on Wait time for the iDRAC to switch from dedicated mode to shared mode. Legal Values Integral values: 5–255 Default Value 5 Write Privilege Configure iDRAC License Required iDRAC Express or iDRAC Enterprise Depende ncy None iDRAC.NIC.DNSDomainFromDHCP (Read or Write) Descripti on Specifies that the iDRAC DNS domain name must be assigned from the network DHCP server.
iDRAC.NIC.DNSDomainName (Read or Write) Descripti on The DNS Domain Name. Legal Values A string of up to 254 ASCII characters Default Value Not Applicable Write Privilege Configure iDRAC License Required iDRAC Express or iDRAC Enterprise Depende ncy Can be set only if NIC.DNSDomainFromDHCP is disabled. iDRAC.NIC.DNSDomainNameFromDHCP (Read or Write) Descripti on Specifies that the iDRAC DNS domain name must be assigned from the network DHCP server.
iDRAC.NIC.DNSRacName (Read or Write) Descripti on The iDRAC name. Legal Values String of up to 63 ASCII characters Default Value Not Applicable Write Privilege Configure iDRAC License Required iDRAC Express or iDRAC Enterprise Depende ncy None iDRAC.NIC.DNSRegister (Read or Write) Descripti on Registers the iDRAC name with the DNS server.
iDRAC.NIC.Duplex (Read or Write) Descripti on Specifies the duplex setting for the iDRAC NIC. Legal Values • • Default value 1 — Full Write Privilege Configure iDRAC License Required iDRAC Express or iDRAC Enterprise Depende ncy None 0 — Half 1 — Full iDRAC.NIC.Enable (Read or Write) Descripti on Enables or Disables the iDRAC network interface controller.
iDRAC.NIC.Failover (Read or Write) Descripti on Enables or disables failover for iDRAC to switch from shared to dedicated. Legal Values • • • • • • Default Value 0 — None Write Privilege Configure iDRAC License Required iDRAC Express or iDRAC Enterprise Depende ncy Possible Values depend on current NICSelection settings. 0 — None 2 — LOM1 3 — LOM2 4 — LOM3 5 — LOM4 6 — All iDRAC.NIC.MACAddress (Read or Write) Descripti on The MAC Address of the iDRAC.
iDRAC.NIC.MTU (Read or Write) Descripti on The size in bytes of the maximum transmission unit uses the iDRAC NIC. Legal Values Integral values: 576–1500 Default Value 1500 Write Privilege Configure iDRAC License Required iDRAC Express or iDRAC Enterprise Depende ncy None iDRAC.NIC.Selection (Read or Write) Descripti on Specifies the current mode of operation for the iDRAC network interface controller.
iDRAC.NIC.SharedNICScanTime (Read or Write) Descripti on Wait time for the iDRAC to switch from shared mode to dedicated mode. Legal Values Integral values: 5–255 Default Value 30 Write Privilege Configure iDRAC License Required iDRAC Express or iDRAC Enterprise Depende ncy None iDRAC.NIC.Speed (Read or Write) Descripti on Specifies the speed for iDRAC NIC. NOTE: To set this property: • • • Legal Values • • • iDRAC.NIC.Selection must be set to Dedicated mode. iDRAC.NIC.
Write Privilege Configure iDRAC License Required iDRAC Express or iDRAC Enterprise Depende ncy Cannot change NIC Speed unless AutoNeg is set to disabled. iDRAC.NIC.VLanEnable (Read Only) Descripti on Enables or disables the VLAN capabilities of the iDRAC. Legal Values • • Default Value 0 — Disabled Write Privilege Configure iDRAC License Required iDRAC Express or iDRAC Enterprise Depende ncy None NOTE: This object is applicable only to iDRAC on Racks and Towers.
Write Privilege Configure iDRAC License Required iDRAC Express or iDRAC Enterprise Depende ncy None iDRAC.NIC.VLanPriority (Read Only) Descripti on Specifies the VLAN priority for the network VLAN configuration. Legal Values Integral values: 0–7 Default Value 0 Write Privilege Configure iDRAC License Required iDRAC Express or iDRAC Enterprise Depende ncy None NOTE: This object is applicable only to iDRAC on Racks and Towers. iDRAC.
Default Value Disabled Write Privilege Configure iDRAC License Required iDRAC Express or iDRAC Enterprise Depende ncy None iDRAC.NICStatic.DNSDomainName (Read or Write) Descripti on The DNS Domain Name. Legal Values • • Default Value Not Applicable Write Privilege Configure iDRAC License Required iDRAC Express or iDRAC Enterprise Depende ncy None 0 — Disabled 1 — Enabled iDRAC.NTPConfigGroup To configure the properties of NTP server, use the objects in this group. iDRAC.NTPConfigGroup.
Default Value Not Applicable Write Privilege Configure iDRAC License Required iDRAC Express or iDRAC Enterprise Depende ncy None iDRAC.NTPConfigGroup.NTP2 (Read or Write) Descripti on Configure NTP Server 2 Address. Legal Values String of up to 254 ASCII characters Default Value Not Applicable Write Privilege Configure iDRAC License Required iDRAC Express or iDRAC Enterprise Depende ncy None iDRAC.NTPConfigGroup.NTP3 (Read or Write) Descripti on Configure NTP Server 3 Address.
License Required iDRAC Express or iDRAC Enterprise Depende ncy None iDRAC.NTPConfigGroup.NTPEnable (Read or Write) Descripti on On iDRAC, enable or disable NTP server access to iDRAC. Legal Values • • Default Value 0 — Disabled Write Privilege Configure iDRAC License Required iDRAC Express or iDRAC Enterprise Depende ncy None 0 — Disabled 1 — Enabled iDRAC.NTPConfigGroup.
iDRAC.OS-BMC To manage OS-BMC pass-through feature, use the object in this group. iDRAC.OS-BMC.AdminState (Read or Write) Description On iDRAC pass through, enable or disable administrative state of OS. Legal Values • • Default Value 0 — Disabled Write Privilege Configure iDRAC License Required iDRAC Express or iDRAC Enterprise Dependency Can be set only if iDRAC.OS-BMC.PTCapability is set to Capable. 0 — Disabled 1 — Enabled iDRAC.OS-BMC.
iDRAC.OS-BMC.PTCapability (Read or Write) Descripti on Operating System to iDRAC Pass Through Capability status. Legal Values • • Default Value Depends on the server capability. Write Privilege Configure iDRAC License Required iDRAC Express or iDRAC Enterprise Depende ncy None 0 — Capable 1 — Not Capable or Unknown iDRAC.OS-BMC.PTMode (Read or Write) Description Enables the pass-through with shared LOM or USB. NOTE: To enable the pass-through, make sure that iDRAC.OS-BMC.AdminState is enabled.
iDRAC.OS-BMC.UsbNicIpAddress (Read or Write) Description Displays the USB NIC IP address. Legal Values Valid IPv4 address Default Value 169.254.0.1 Write Privilege Configure iDRAC License Required iDRAC Express or iDRAC Enterprise Dependency None iDRAC.Racadm To manage Remote RACADM connection settings, use the object in this group. iDRAC.Racadm.Enable (Read or Write) Descripti on Enables or disables Remote RACADM interface.
iDRAC.Racadm.Timeout (Read or Write) Description Defines the idle timeout in seconds of the Remote RACADM interface. Legal Values • • Default Value 60 Write Privilege Configure iDRAC License Required iDRAC Express or iDRAC Enterprise Dependency None 0 — No timeout Integral values: 60–10800 iDRAC.RemoteHosts Use the objects in this group to manage the properties for configuration of the SMTP server. iDRAC.RemoteHost.
iDRAC.RemoteHosts.SMTPServerIPAddress (Read or Write) Descripti on IPv4 or IPv6 address of the network SMTP server. Legal Values String representing a valid SMTP server IPv4 or IPv6 address Default Value 0.0.0.0 Write Privilege Configure iDRAC License Required iDRAC Express or iDRAC Enterprise Depende ncy None iDRAC.RFS To configure Remote file share access to iDRAC, use the object in this group iDRAC.RFS.MediaAttachState (Read Only) Descripti on RFS Media attach state.
iDRAC.RSM The objects in this group manage the Rack Style Management (RSM) settings. iDRAC.RSM.RSMCapability (Read Only) Descriptio n Specifies the status of RSM capability. Legal Values • 0 — Disabled • 1 — Enabled Default Value 0 — Disabled License Required iDRAC Express or iDRAC Enterprise Dependen cy None iDRAC.RSM.RSMSetting (Read Only) Descriptio n Specifies the status of RSM setting.
iDRAC.Security Use the objects in this group to configure SSL certificate signing request settings. For the country code, go to the link: http://www.iso.org/iso/country_codes/ iso_3166_code_lists.htm. iDRAC.Security.CsrCommonName (Read or Write) Descripti on Specifies the CSR Common Name (CN) that must be an IP as given in the certificate.
iDRAC.Security.CsrEmailAddr (Read or Write) Descripti on Specifies the CSR email address. Legal Values Valid email address string of up to 254 ASCII characters. Default Value Not Applicable Write Privilege Configure iDRAC License Required iDRAC Express or iDRAC Enterprise Depende ncy None iDRAC.Security.CsrKeySize (Read or Write) Descripti on Specifies the SSL asymmetric key size for the CSRs.
iDRAC.Security.CsrLocalityName (Read or Write) Descripti on Specifies the CSR Locality (L). Legal Values String of up to 254 ASCII characters Default Value Not Applicable Write Privilege Configure iDRAC License Required iDRAC Express or iDRAC Enterprise Depende ncy None iDRAC.Security.CsrOrganizationName (Read or Write) Descripti on Specifies the CSR Organization Name (O).
iDRAC.Security.CsrOrganizationUnit (Read or Write) Description Specifies the CSR Organization Unit (OU). Legal Values String of up to 254 ASCII characters Default Value Not Applicable Write Privilege Configure iDRAC License Required iDRAC Express or iDRAC Enterprise Dependency None iDRAC.Security.CsrStateName (Read or Write) Descripti on Specifies the CSR State Name (S).
iDRAC.Serial.BaudRate (Read or Write) Descripti on Sets the Baud rate on the iDRAC serial port. Legal Values • • • • • Default Value 115200 Write Privilege Configure iDRAC License Required iDRAC Express or iDRAC Enterprise Depende ncy None 9600 19200 38400 57600 115200 iDRAC.Serial.Command (Read or Write) Descripti on Specifies a serial command that is executed after the user logs in to the serial console interface.
iDRAC.Serial.Enable (Read or Write) Descripti on Enables or disables the iDRAC serial console interface. Legal Values • • Default Value 0 — Disabled Write Privilege Configure iDRAC License Required iDRAC Express or iDRAC Enterprise Depende ncy None 0 — Disabled 1 — Enabled iDRAC.Serial.HistorySize (Read or Write) Descripti on Specifies the maximum size of the serial history buffer. Legal Values Integral values from 0 to 8192.
iDRAC.Serial.IdleTimeout (Read or Write) Descripti on The maximum number of seconds to wait before an idle serial console session is disconnected. Legal Values • • Default Value 300 Write Privilege Configure iDRAC License Required iDRAC Express or iDRAC Enterprise Depende ncy None 0 — No timeout Integral values: 60–10800 iDRAC.Serial.NoAuth (Read or Write) Descripti on Enables or disables iDRAC serial console login authentication.
iDRAC.SerialRedirection The objects in this group manage Serial Redirection properties of iDRAC. NOTE: It supports only rack and tower systems. iDRAC.SerialRedirection.Enable (Read or Write) Descripti on Enables or disables the console for COM2 port redirection. Legal Values • • Default Value 1 — Enabled Write Privilege Configure iDRAC License Required iDRAC Express or iDRAC Enterprise Depende ncy None 0 — Disabled 1 — Enabled iDRAC.SerialRedirection.
Depende ncy None iDRAC.serverboot The objects in this group manages the server boot options. iDRAC.serverboot.BootOnce (Read or Write) Descripti on Enables or disables BootOnce option for the configured device. Legal Values • • Default values 1 — Enabled Write Privilege Login and configure iDRAC License Required iDRAC Express or iDRAC Enterprise Depende ncy Read only if iDRAC.ServerBoot.FirstBootDevice is set to either BIOS (BIOS Setup), F10 (Lifecycle Controller), or F11 (BIOS Boot Manager).
• • F11 (BIOS Boot Manager) Attached vFlash Partition Label Default value Normal Write Privilege Login and configure iDRAC License Required iDRAC Express or iDRAC Enterprise Depende ncy None iDRAC.ServiceModule The objects in this group manages the properties of the ISM modules. iDRAC.ServiceModule.LCLReplication (Read or Write) Descripti on Enables Lifecycle log in operating system log Baud rate on the iDRAC serial port.
• 2 — NA Default Value 2 — NA License Required iDRAC Express or iDRAC Enterprise Dependen cy None iDRAC.ServiceModule.OSInfo (Read or Write) Descripti on Provides information about operating system through iDRAC Service Module. Legal Values • • Default Value 1 — Enabled Write Privilege Configure iDRAC License Required iDRAC Express or iDRAC Enterprise Depende ncy None 0 — Disabled 1 — Enabled iDRAC.ServiceModule.
License Required iDRAC Express or iDRAC Enterprise Depende ncy None iDRAC.ServiceModule.ServiceModuleState (Read or Write) Descripti on Indicates the status of Service Module process on the host operating system. Legal Values • • Default Value 1 — Enabled Write Privilege Configure iDRAC License Required iDRAC Express or iDRAC Enterprise Depende ncy None 0 — Disabled 1 — Enabled iDRAC.ServiceModule.
iDRAC.ServiceModule.WatchdogRecoveryAction (Read and Write) Descripti on Configures recovery action on watchdog alert. Legal Values • • • • Default Value 0 — None Write Privilege Configure iDRAC License Required iDRAC Express or iDRAC Enterprise Depende ncy If the iDRAC.ServiceModule.WatchdogState object is 'Disabled', then the value cannot be set. 0 — None 1 — Reboot 2 — Poweroff 3 — Powercycle iDRAC.ServiceModule.
iDRAC.ServiceModule.WatchdogState (Read and Write) Descripti on Enables or disables the watchdog timer through iDRAC Service Module. Legal Values • • Default Value 0 — Disabled Write Privilege Configure iDRAC License Required iDRAC Express or iDRAC Enterprise Depende ncy The value is disabled if OpenManage Server Administrator is detected or operating system Watchdog is enabled. 0 — Disabled 1 — Enabled iDRAC.SmartCard The objects in this group enable you to access iDRAC using a smart card.
iDRAC.SmartCard.SmartCardLogonEnable (Read or Write) Descripti on Enables or disables Smart card login support. Legal Values • • • Default Value Not Applicable Write Privilege Configure iDRAC and Configure User License Required iDRAC Enterprise Depende ncy Disable ActiveDirectory.SSOEnable 0 — Disabled 1 — Enabled 2 — Enabled with Remote RACADM iDRAC.SNMP The objects in this group enable you to configure the SNMP agent and trap capabilities. iDRAC.SNMP.
Depende ncy None iDRAC.SNMP.AgentEnable (Read or Write) Descripti on Enables or disables the SNMP Agent on the iDRAC. Legal Values • • Default Value 1 — Enabled Write Privilege Configure iDRAC License Required iDRAC Express or iDRAC Enterprise Depende ncy None 0 — Disabled 1 — Enabled iDRAC.SNMP.AlertPort (Read or Write) Descripti on Specifies the SNMP alert port for traps.
iDRAC.SNMP.DiscoveryPort (Read or Write) Descripti on Specifies the SNMP agent port on iDRAC. Legal Values Integral values: 1–65535 Default Value 161 Write Privilege Configure iDRAC License Required iDRAC Express Depende ncy None iDRAC.SNMP.SNMPProtocol (Read or Write) Descripti on Specifies the SNMP protocol.
iDRAC.SNMP.TrapFormat (Read or Write) Descripti on Specifies the SNMP format. Legal Values • • • Default Value 0 — SNMPv1 Write Privilege Configure iDRAC License Required iDRAC Express or iDRAC Enterprise Depende ncy None 0 — SNMPv1 1 — SNMPv2 2 — SNMPv3 iDRAC.SNMP.Alert The objects in this group configures the SNMP alert settings. This group is indexed from 1 to 8. iDRAC.SNMP.Alert.DestAddr (Read or Write) Descripti on IPv4, IPv6 or FQDN address of the target destination to receive alters.
Depende ncy None iDRAC.SNMP.Alert.Enable (Read or Write) Descripti on Enables or disables SNMP alert for the given index. Legal Values • • Default Value Not Applicable Write Privilege Configure iDRAC License Required None Depende ncy None 0 — Disabled 1 — Enabled iDRAC.SNMP.Alert.SNMPv3UserID (Read Only) Descripti on Indicates the index of the user to which this alert is configured.
iDRAC.SNMP.Alert.SNMPv3Username (Read or Write) Descripti on Specifies the SNMP v3 user name for the given index. Legal Values String of up to 16 ASCII characters Default Value Not Applicable Write Privilege Configure iDRAC License Required iDRAC Express Depende ncy None iDRAC.SSH The objects in this group provide configuration parameters for the SSH interface to iDRAC. iDRAC.SSH.Enable (Read or Write) Descripti on Enables or disables SSH.
iDRAC.SSH.Port (Read or Write) Descripti on Specifies the port number for the iDRAC SSH interface. Legal Values Integral values: 1–65535 Default Value 22 Write Privilege Configure iDRAC License Required iDRAC Express or iDRAC Enterprise Depende ncy None iDRAC.SSH.Timeout (Read or Write) Descripti on Defines the secure shell idle timeout.
iDRAC.SysLog The objects in this group provide the properties for configuration of the SMTP server. iDRAC.SysLog.Port (Read or Write) Descripti on Remote syslog port number. Legal Values Integral values: 1–65535 Default Value 514 Write Privilege Configure iDRAC License Required iDRAC Enterprise Depende ncy None iDRAC.SysLog.PowerLogEnable (Read or Write) Descripti on Enables or disables the Power Log feature.
iDRAC.SysLog.PowerLogInterval (Read or Write) Descripti on Configure time delay for power logging. Legal Values Integral values: 1–1440 Default Value 5 Write Privilege Configure iDRAC License Required iDRAC Enterprise Depende ncy None iDRAC.SysLog.Server1 (Read or Write) Descripti on Name of remote syslog server 1.
iDRAC.SysLog.Server2 (Read or Write) Descripti on Name of remote syslog server 2. Legal Values String of up to 63 ACSII characters Default Value Not Applicable Write Privilege Configure iDRAC License Required iDRAC Enterprise Depende ncy None iDRAC.SysLog.Server3 (Read or Write) Descripti on Name of remote syslog server 3.
iDRAC.SysLog.SysLogEnable (Read or Write) Descripti on Enables or disables remote syslog. Legal Values • • Default Value Not Applicable Write Privilege Configure iDRAC License Required iDRAC Enterprise Depende ncy None 0 — Disabled 1 — Enabled iDRAC.Telnet The objects in this group provide configuration parameters for the Telnet interface to iDRAC. iDRAC.Telnet.Enable (Read or Write) Descripti on Enables or disables Telnet.
Depende ncy None iDRAC.Telnet.Port (Read or Write) Descripti on Specifies the port number for the iDRAC Telnet interface. Legal Values Integral values: 1–65535 Default Value 23 Write Privilege Configure iDRAC License Required iDRAC Express or iDRAC Enterprise Depende ncy None iDRAC.Telnet.Timeout (Read or Write) Descripti on Defines the Telnet idle timeout.
iDRAC.Time The objects in this group enable you to manage timezone setting for iDRAC. iDRAC.Time.DayLightOffset (Read or Write) Descriptio n Specifies the daylight savings offset (in minutes) to use for the iDRAC Time. Legal Values Integral values: 0 – 60 Default Value 0 Write Privilege Configure iDRAC License Required iDRAC Express or iDRAC Enterprise Dependen cy None iDRAC.Time.Timezone (Read or Write) Descripti on Configure the time zone.
iDRAC.Time.TimeZoneOffset (Read or Write) Descriptio n Specifies the time zone offset (in minutes) from Greenwich Mean Time (GMT) or Coordinated Universal Time (UTC) to use for the iDRAC Time. Legal Values Integral values: -43200 – 46800 Default Value 0 Write Privilege Configure iDRAC License Required iDRAC Express or iDRAC Enterprise Dependen cy None iDRAC.Tuning The objects in this group enable you to manage iDRAC tuning and configuration parameters. iDRAC.Tuning.
iDRAC.Update The objects in this group enable you to manage configuration parameters for iDRAC firmware update. iDRAC.Update.FwUpdateIPAddr (Read or Write) Descripti on Specifies the TFTP server address to be used for iDRAC firmware update operations. Legal Values Valid IPv4, IPv6, or FQDN address of the TFTP server Default Value Not Applicable Write Privilege Configure iDRAC License Required iDRAC Express or iDRAC Enterprise Depende ncy None iDRAC.Update.
iDRAC.Update.FwUpdateTFTPEnable (Read or Write) Descripti on Enables or disables iDRAC firmware updates from a TFTP server. Legal Values • • Default Value 1 — Enabled Write Privilege Configure iDRAC License Required iDRAC Express or iDRAC Enterprise Depende ncy None 0 — Disabled 1 — Enabled iDRAC.USB The objects in this group manages the front panel USB. iDRAC.USB.ConfigurationXML (Read or Write) Descripti on Manages the configuration xml feature using the front panel USB.
iDRAC.USB.ManagementPortMode (Read or Write) Descripti on Allows you to configure the front panel USB mode. Legal Values • Automatic • Standard OS Use • iDRAC Direct Only Default Value Automatic Write Privilege Server Control License Required iDRAC Express and iDRAC Enterprise Depende ncy Not Applicable iDRAC.UserDomain The objects in this group enable you to manage the Active Directory user domain names. This group is indexed from 1 to 40. iDRAC.UserDomain.
Depende ncy None iDRAC.Users The objects in this group enable you to manage information about all iDRAC users. This group is indexed from 1 to 16. iDRAC.Users.Enable (Read or Write) Descripti on Enables or disables an individual user. Legal Values • • Default Value 0 — Disabled. However, Root user is Enabled. Write Privilege Configure iDRAC License Required iDRAC Express or iDRAC Enterprise Depende ncy Both username and password must be configured prior to enabling the user.
Write Privilege Configure iDRAC License Required iDRAC Express or iDRAC Enterprise Depende ncy Both user name and password must be configured prior to setting this object. iDRAC.Users.IpmiSerialPrivilege (Read or Write) Descripti on Specifies the maximum IPMI Serial privilege.
License Required iDRAC Express Depende ncy User name must be configured prior to setting this object. iDRAC.Users.Password (Read or Write) Descripti on Configuring the iDRAC user password. Legal Values String of up to 254 characters Default Value Not Applicable Write Privilege Configure iDRAC License Required iDRAC Express or iDRAC Enterprise Depende ncy Cannot be set without first setting the user name. iDRAC.Users.
iDRAC.Users.SHA256PasswordSalt (Read or Write) Descripti on Indicates the Salt string added to password before hash. Legal Values String of 32 characters Write Privilege Server Control License Required iDRAC Express Depende ncy User name must be configured prior to setting this object. iDRAC.Users.Privilege (Read or Write) Descripti on Specifies the role-based authority privileges allowed for the user.
Default Value Not Applicable Write Privilege Server Control License Required iDRAC Express Depende ncy User name must be configured prior to setting this object. iDRAC.Users.SNMPv3AuthenticationType (Read or Write) Descripti on Configure SNMPv3 authentication protocol type. Legal Values • • • Default Value 2 — SHA Write Privilege Configure iDRAC and Configure User License Required iDRAC Express or iDRAC Enterprise Depende ncy None 0 — None 1 — MD5 2 — SHA iDRAC.Users.
Write Privilege Configure iDRAC and Configure User License Required iDRAC Express or iDRAC Enterprise Depende ncy None iDRAC.Users.SNMPv3PrivacyType (Read or Write) Descripti on Configure SNMPv3 privacy protocol type. Legal Values • • • Default Value 2 — AES Write Privilege Configure iDRAC and Configure User License Required iDRAC Express or iDRAC Enterprise Depende ncy None 0 — None 1 — DES 2 — AES iDRAC.Users.SolEnable (Read or Write) Descripti on Enables or Disables SOL for the user.
License Required iDRAC Express or iDRAC Enterprise Depende ncy Both username and password must be configured prior to sets. iDRAC.Users.UserName (Read or Write) Descripti on iDRAC User Name. Legal Values String of up to 16 ASCII characters Default Value Not Applicable Write Privilege Configure iDRAC and Configure User License Required iDRAC Express or iDRAC Enterprise Depende ncy None iDRAC.vflashpartition The objects in this group manage vFlash SD partitions on iDRAC.
Write Privilege Login and configure iDRAC License Required iDRAC Enterprise Depende ncy vFlash SD card must be enabled. Partition at the specified index must be created. iDRAC.vflashpartition.AttachState (Read or Write) Descripti on Specifies if the vFlash SD partition is attached or detached. Legal Values • • Default value 0 — Detached Write Privilege Login and configure iDRAC License Required iDRAC Enterprise Depende ncy vFlash SD card must be enabled.
Depende ncy vFlash SD card must be enabled. Partition at the specified index must be created. iDRAC.vflashpartition.FormatType (Read or Write) Descripti on Specifies the file system format type of the vFlash SD partition. Legal Values • • • • • Default value None Write Privilege Login and configure iDRAC License Required iDRAC Enterprise Depende ncy vFlash SD card must be enabled. Partition at the specified index must be created. FAT16 FAT32 EXT2 EXT3 RAW iDRAC.vflashpartition.
iDRAC.vflashpartition.VolumeLabel (Read or Write) Descripti on Specifies the label assigned to the partition during the vFlash SD partition creation. Legal Values String of up to six characters. Default value None Write Privilege Login and configure iDRAC License Required iDRAC Enterprise Depende ncy vFlash SD card must be enabled. Partition at the specified index must be created. iDRAC.vflashsd The objects in this group manage vFlash SD properties on iDRAC. iDRAC.vflashsd.
iDRAC.vflashsd.Enable (Read or Write) Descripti on Enables or disables the vFlash SD card on iDRAC. Legal Values • • Default value 0 — Disabled Write Privilege Login and configure iDRAC License Required iDRAC Enterprise Depende ncy vFlash SD card must be enabled. 0 — Disabled 1 — Enabled iDRAC.vflashsd.Health (Read or Write) Descripti on Specifies current health status of the vFlash SD Card.
iDRAC.vflashsd.Initialized (Read or Write) Descripti on Specifies if the vFlash SD card is initialized or not. Legal Values • • Default value None Write Privilege Login and configure iDRAC License Required iDRAC Enterprise Depende ncy vFlash SD card must be enabled. 0 — Not Initialized 1 — Initialized iDRAC.vflashsd.Licensed (Read or Write) Descripti on Specifies if the SD card or vFlash SD card is inserted or not.
iDRAC.vflashsd.Size (Read or Write) Descripti on Specifies the remaining size of the vFlash SD card for usage. Legal Values Integer value in MB. Default value None Write Privilege Login and configure iDRAC License Required iDRAC Enterprise Depende ncy vFlash SD card must be enabled. iDRAC.vflashsd.WriteProtect (Read or Write) Descripti on Displays if the physical write protect is enabled or disabled on the vFlash SD card.
iDRAC.VirtualConsole.AccessPrivilege (Read or Write) Descripti on Default action upon session sharing request timeout. Legal Values • • • Default Value 0 — Deny Access Write Privilege Configure iDRAC License Required iDRAC Express (For Blades) or iDRAC Enterprise Depende ncy None 0 — Deny Access 1 — Read Only Access 2 — Full Access iDRAC.VirtualConsole.AttachState (Read or Write) Descripti on Specifies the Attach State for the Virtual Console.
iDRAC.VirtualConsole.Enable (Read or Write) Descripti on Enables or disables the Virtual Console. Legal Values • • Default Value 1 — Enabled Write Privilege Configure iDRAC License Required iDRAC Express (For Blades) or iDRAC Enterprise Depende ncy None 0 — Disabled 1 — Enabled iDRAC.VirtualConsole.EncryptEnable (Read or Write) Descripti on Encrypts the video in a Virtual Console session.
iDRAC.VirtualConsole.LocalVideo (Read or Write) Descripti on Enables or disables the local server video. Legal Values • • Default Value 1 — Enabled Write Privilege Configure iDRAC License Required iDRAC Express (For Blades) or iDRAC Enterprise Depende ncy None 0 — Disabled 1 — Enabled iDRAC.VirtualConsole.MaxSessions (Read or Write) Descripti on Specifies maximum number of virtual console sessions.
iDRAC.VirtualConsole.PluginType (Read or Write) Descripti on To use virtual console, when running from the browser specify the plugin type. Legal Values • • Default Value 0 — Active X Write Privilege Configure iDRAC License Required iDRAC Express (For Blades) or iDRAC Enterprise Depende ncy None 0 — Active X 1 — Java iDRAC.VirtualConsole.Port (Read or Write) Descripti on Specifies the virtual KVM port.
iDRAC.VirtualConsole.Timeout (Read or Write) Descripti on Defines the idle timeout in seconds for the virtual console. Legal Values Integral values: 60–10800 Default Value 1800 Write Privilege Configure iDRAC License Required iDRAC Express (For Blades) or iDRAC Enterprise Depende ncy None iDRAC.VirtualMedia The objects in this group enable you to manage virtual media configuration parameters of iDRAC. iDRAC.VirtualMedia.
Depende ncy None iDRAC.VirtualMedia.BootOnce (Read or Write) Descripti on Enables or disables the virtual media boot once feature of the iDRAC. Legal Values • • Default Value 0 — Disabled Write Privilege Virtual Media License Required iDRAC Express (For Blades) or iDRAC Enterprise Depende ncy None 0 — Disabled 1 — Enabled iDRAC.VirtualMedia.FloppyEmulation (Read or Write) Descripti on Enables of disables floppy emulation of the attached virtual media.
iDRAC.VNCServer The objects in this group manages configuration of the VNC Server on iDRAC. iDRAC.VNCServer.Enable (Read or Write) Descripti on Enables or disables VNC server on iDRAC. Legal Values • • Default value 0 — Disabled Write Privilege Login or configure iDRAC License Required iDRAC Enterprise Depende ncy None 0 — Disabled 1 — Enabled iDRAC.VNCServer.LowerEncryptionBitLength (Read or Write) Descripti on Lower encryption bit length.
iDRAC.VNCServer.Password (Read or Write) Descripti on Password for logging into VNC session. Legal Values String of up to 8 characters Default Value None Write Privilege Login or configure iDRAC License Required iDRAC Enterprise Depende ncy None iDRAC.VNCServer.Port (Read or Write) Descripti on Port number for VNC session Legal Values Integer values from 1024 to 65535 Default Value 5901 Write Privilege Login or configure iDRAC License Required iDRAC Enterprise Depende ncy None iDRAC.
Default Value 300 Write Privilege Login or configure iDRAC License Required iDRAC Enterprise Depende ncy None iDRAC.WebServer The objects in this group provide configuration parameters for iDRACs' Webserver. iDRAC.WebServer.Enable (Read or Write) Descripti on Enables or disables iDRAC WebServer. Legal Values • • Default Value 1 — Enabled Write Privilege Configure iDRAC License Required iDRAC Express or iDRAC Enterprise Depende ncy None 0 — Disabled 1 — Enabled iDRAC.WebServer.
Default Value 80 Write Privilege Configure iDRAC License Required iDRAC Express or iDRAC Enterprise Depende ncy None iDRAC.WebServer.HttpsPort (Read or Write) Descripti on Specifies the port number for HTTPs communication with the iDRAC. Legal Values Integral values: 1–65535 Default Value 443 Write Privilege Configure iDRAC License Required iDRAC Express or iDRAC Enterprise Depende ncy None iDRAC.Webserver.
License Required iDRAC Express or iDRAC Enterprise Depende ncy None iDRAC.WebServer.LowerEncryptionBitLength (Read or Write) Descripti on Lower Encryption Bit Length. Legal Values • • Default Value 1 — Enabled (128 Bit or Higher) Write Privilege Configure iDRAC License Required iDRAC Express or iDRAC Enterprise Depende ncy None 0 — Disabled (Auto Negotiate) 1 — Enabled (12 Bit or Higher) iDRAC.WebServer.Timeout (Read or Write) Descripti on Defines the webserver timeout.
BIOS.BiosBootSettings You can manage the BIOS start settings using the objects in this group. BIOS.BiosBootSettings.BootSeq (Read or Write) Descripti on Determines the Bios start sequence of the system. Legal Values None Default Value Not Applicable Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Depende ncy Read Only if BootMode is set to UEFI BIOS.BiosBootSettings.BootMode (Read or Write) Descripti on Determines the start mode of the system.
BIOS.BiosBootSettings.BootSeqRetry (Read or Write) Descripti on Enables or disables the boot sequence retry feature. Legal Values Enabled Default Value Not Applicable Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Depende ncy None Disabled BIOS.BiosBootSettings.HddFailover (Read or Write) Descripti on Specifies the devices in the Hard-Disk Drive Sequence menu that are attempted in the boot sequence.
BIOS.BiosBootSettings.HddSeq (Read or Write) Descripti on HDD boot sequence Legal Values None Default Value Not Applicable Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Depende ncy Read Only if Boot mode is set to UEFI BIOS.BiosBootSettings.
BIOS.BiosBootSettings.SetBootOrderFqddn (Read or Write) Descripti on Specifies a list of FQDDs that has the boot list to apply on the next boot. In the attribute SetBootOrderFqddn, the value of n can be 1 to 16 Legal Values String of UEFI boot devices Default Value Not Applicable Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Depende ncy None BIOS.BiosBootSettings.
BIOS.EmbServerMgmt The objects in this group assist in embedded server management. BIOS.EmbServerMgmt.FrontLcd (Read or Write) Descripti on Allows to display the default (Model name and number) or a user-defined string in the front-panel LCD. To modify the advanced features of the front-panel LCD, press F2 during boot to enter System Setup and then select iDRAC Settings.
Depende ncy None BIOS.IntegratedDevices You can use the objects in this group to manage the integrated devices such as internal NIC and integrated USB. BIOS.IntegratedDevices.EmbNic1 (Read or Write) Descripti on Enables or disables the operating system interface of the embedded NIC1. Legal Values • • • • Default Value Not Applicable Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Depende ncy None Enabled EnabledPxe EnablediScsi Disabled BIOS.
Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Depende ncy None BIOS.IntegratedDevices.EmbNic2 (Read or Write) Descripti on Enables or disables the operating system interface of the embedded NIC2. Legal Values • • • • Default Value Not Applicable Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Depende ncy None Enabled EnabledPxe EnablediScsi Disabled BIOS.IntegratedDevices.
Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Depende ncy None BIOS.IntegratedDevices.EmbNic3Nic4 (Read or Write) Descripti on Enables or disables the operating system interface of the embedded NIC3 and NIC4 controllers. Legal Values • • • Default Value Not Applicable Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Depende ncy None Enabled Disabled OS Disabled BIOS.IntegratedDevices.
License Required iDRAC Express or iDRAC Enterprise Depende ncy None BIOS.IntegratedDevices.EmbVideo (Read or Write) Descripti on Enables or disables the BIOS support for the embedded video controller. Legal Values • • Default Value Not Applicable Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Depende ncy None Enabled Disabled BIOS.IntegratedDevices.IntegratedNetwork1 (Read or Write) Descripti on Enables or disables the Integrated Network Card 1.
BIOS.IntegratedDevices.IntegratedNetwork2 (Read or Write) Descripti on Enables or disables the integrated network card 2. Legal Values • • Default Value Not Applicable Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Depende ncy None Enabled DisabledOS BIOS.IntegratedDevices.IntegratedRaid (Read or Write) Descripti on Enables or disables the integrated RAID controller.
BIOS.IntegratedDevices.IntegratedSas (Read or Write) Descripti on Enables or disables the integrated SAS controller. Legal Values • • Default Value Not Applicable Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Depende ncy None Enabled Disabled BIOS.IntegratedDevices.InternalSdCard (Read or Write) Descripti on Enables or disables the internal SD Card port.
BIOS.IntegratedDevices.InternalSdCardRedundancy (Read or Write) Descripti on Sets the SD Card redundancy mode. Legal Values • • Default Value Not Applicable Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Depende ncy Read Only if 'InternalSdCard' is set to 'Off'. Mirror Disabled BIOS.IntegratedDevices.InternalUsb (Read or Write) Descripti on Enables or disables the internal USB port.
BIOS.IntegratedDevices.InternalUsb1 (Read or Write) Descripti on Enables or disables the internal USB port 1. Legal Values • • Default Value Not Applicable Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Depende ncy None On Off BIOS.IntegratedDevices.InternalUsb2 (Read or Write) Descripti on Enables or disables the internal USB port 2.
BIOS.IntegratedDevices.IoatEngine (Read or Write) Descripti on Enables or disables the I/O Acceleration technology (I/OAT) option. Legal Values • • Default Value Not Applicable License Required iDRAC Express or iDRAC Enterprise Depende ncy None Enabled Disabled BIOS.IntegratedDevices.MmioAbove4GB (Read or Write) Descripti on Enables or disables support for PCIe devices that require large amount of memory. Enable this option only for 64-bit operating systems.
Default Value Not Applicable Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Depende ncy None BIOS.IntegratedDevices.SriovGlobalEnable (Read or Write) Descripti on Enables or disables BIOS configuration of Single Root I/O Virtualization (SR-IOV) devices. Legal Values • • Default Value Not Applicable Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Depende ncy None Enabled Disabled BIOS.IntegratedDevices.
Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Depende ncy None BIOS.MemSettings To manage memory-related configuration settings, use the objects in this group. BIOS.MemSettings.MemLowPower (Read or Write) Descripti on Enables or disables the low-power mode of the memory. Legal Values • • Default Value Not Applicable Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Depende ncy None Enabled Disabled BIOS.MemSettings.
• SpareWithAdvEccMode Default Value Not Applicable Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Depende ncy None BIOS.MemSettings.MemOptimizer (Read or Write) Descripti on Configure the memory optimizer setting. Legal Values • • Default Value Not Applicable Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Depende ncy None Enabled Disabled BIOS.MemSettings.
License Required iDRAC Express or iDRAC Enterprise Depende ncy None BIOS.MemSettings.MemTest (Read or Write) Descripti on Specifies whether BIOS software-based system memory tests are conducted during POST. Legal Values • • Default Value Not Applicable Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Depende ncy None Enabled Disabled BIOS.MemSettings.
BIOS.MemSettings.RedundantMem (Read or Write) Descripti on Enables or disables the redundant memory feature. Legal Values • • • • • • Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Depende ncy None Disabled Spare Mirror IntraNodeMirror DimmSpare Dddc BIOS.MemSettings.
BIOS.MemSettings.RedundantMemInUse (Read Only) Descripti on Display the current redundant memory setting in BIOS. Legal Values • • Default Value Not Applicable Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Depende ncy None NotInUse InUse BIOS.MemSettings.Serialdbgout (Read or Write) Descripti on Enables or disables the Serial Debug Out option.
• Disabled Default Value Not Applicable Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Depende ncy None BIOS.MemSettings.SysMemSize (Read or Write) Descripti on Indicates the current amount of main memory in the system. Legal Values None Default Value Not Applicable Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Depende ncy None BIOS.MemSettings.
License Required iDRAC Express or iDRAC Enterprise Depende ncy None BIOS.MemSettings.SysMemType (Read or Write) Descripti on Indicates the current type of main memory installed in the system. Legal Values None Default Value Not Applicable Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Depende ncy None BIOS.MemSettings.SysMemVolt (Read or Write) Descripti on Displays the current operating voltage of main memory.
BIOS.MemSettings.VideoMem (Read or Write) Descripti on Indicates the total amount of video memory available to the embedded video controller. Legal Values None Default Value Not Applicable Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Depende ncy None BIOS.MiscSettings To manage the miscellaneous objects settings, use the object in this group. BIOS.MiscSettings.
BIOS.MiscSettings.ErrPrompt (Read or Write) Descripti on Enables or disables the F1 and F2 prompt on error. Legal Values • • Default Value Not Applicable Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Depende ncy None Enabled Disabled BIOS.MiscSettings.InSystemCharacterization (Read or Write) Descripti on The ratio of power and performance of a system is optimized by ISC when it is enabled.
BIOS.MiscSettings.NumLock (Read or Write) Descripti on Enable or disable the system boots with Num locks, not applicable for 84-key keyboards Legal Values • • Default Value Not Applicable Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Depende ncy None On Off BIOS.MiscSettings.ReportKbdErr (Read or Write) Descripti on Enables or disables the keyboard-related error messages to be reported at system startup.
BIOS.MiscSettings.SystemUefiShell (Read or Write) Descripti on Enables or disables the System UEFI Shell as a UEFI boot option choice. Legal Values • • Default Value Not Applicable Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Depende ncy None Enabled Disabled BIOS.MiscSettings.SysMgmtNVByte1 (Read or Write) Descripti on Indicates the system management NVRAM byte 1.
Default Value Not Applicable Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Depende ncy None BIOS.MiscSettings.SystemUefiShell (Read or Write) Descripti on Enables or disables the system UEFI shell as UEFI boot option. Legal Values • Enabled • Disabled Default Value Not Applicable Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Depende ncy None BIOS.MiscSettings.
Depende ncy None BIOS.NetworkSettings The objects in this group manage the iSCSI devices. BIOS.NetworkSettings.PxeDevnEnDis (Read or Write) Descripti on Indicates if the PXE device is enabled or disabled. When enabled, a UEFI boot option is created for the PXE device. For the attribute PxeDevnEnDis, the value of n can be 2 — 4. Legal Values • Enabled • Disabled Default Value None Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Depende ncy None BIOS.
Default Value Not Applicable Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Depende ncy None BIOS.OneTimeBoot.OneTimeBootSeqDev (Read or Write) Descriptio Configure the one time boot sequence device in BIOS. n Legal Values Hard Disk List Default Value Not Applicable Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Dependen Read Only if OneTimeBootMode is not set to OneTimeBootSeq. cy BIOS.OneTimeBoot.
License Required iDRAC Express or iDRAC Enterprise Depende ncy Read Only if OneTimeBootMode is set to Disabled or set to OneTimeBootSeq, OneTimeHddSeq, or OneTimeUefiBootSeq BIOS.OneTimeBoot.OneTimeHddSeqDev (Read or Write) Descripti on Configure the one time Hard Disk Drive (HDD) sequence for BIOS.
BIOS.ProcSettings To configure the processor settings, use the objects in this group. BIOS.ProcSettings.CorePerfBoost (Read or Write) Descripti on Enables or disables CPU core performance booster. Legal Values • • Default Value Not Applicable Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Depende ncy None Enabled Disabled BIOS.ProcSettings.DataReuse (Read or Write) Descripti on Enables or disables data reuse in cache.
BIOS.ProcSettings.DcuIpPrefetcher (Read or Write) Description Enables or disables Data Cache Unit (DCU) IP Prefetcher. Legal Values • • Default Value Not Applicable Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Dependency None Enabled Disabled BIOS.ProcSettings.DcuStreamerPrefetcher (Read or Write) Descripti on Enables or disables Data Cache Unit (DCU) Streamer Prefetcher.
BIOS.ProcSettings.DmaVirtualization (Read or Write) Descripti on Enables or disables hardware capabilities for DMA remapping and virtualization are available. Legal Values • • Default Value Not Applicable Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Depende ncy None Enabled Disabled BIOS.ProcSettings.
BIOS.ProcSettings.LogicalProc (Read or Write) Descripti on To enable report all logical processors and to disable report one logical processor per core. Legal Values • • Default Value Not Applicable Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Depende ncy None Enabled Disabled BIOS.ProcSettings.PerfMonitorDevices (Read or Write) Descripti on Allows to enable or disable the performance monitoring devices.
BIOS.ProcSettings.Proc1Brand (Read or Write) Descriptio Provides the processor brand name. n Legal Values None Default Value Not Applicable Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Dependen None cy BIOS.ProcSettings.Proc1ControlledTurbo (Read or Write) Descripti on Controls the turbo engagement.
BIOS.ProcSettings.Proc1Id (Read or Write) Descripti on Provides the processor's family model and stepping values. Legal Values None Default Value Not Applicable Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Depende ncy None BIOS.ProcSettings.Proc1L2Cache (Read or Write) Descripti on Amount of memory in the corresponding processor cache.
Default Value Not Applicable Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Depende ncy None BIOS.ProcSettings.Proc1NumCores (Read or Write) Descripti on Number of cores in the processor package. Legal Values None Default Value Not Applicable Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Depende ncy None BIOS.ProcSettings.Proc2Brand (Read or Write) Descripti on Provides the processor brand name.
Depende ncy None BIOS.ProcSettings.Proc2ControlledTurbo (Read or Write) Descripti on Controls the turbo engagement. Legal Values • • • • • Default Value Not Applicable Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Depende ncy Not Applicable NOTE: You can enable this option only when System Profile is set to Performance. Disabled ControlledTurboLimit ControlledTurboLimitMinus1 ControlledTurboLimitMinus2 ControlledTurboLimitMinus3 BIOS.ProcSettings.
Depende ncy None BIOS.ProcSettings.Proc2L2Cache (Read or Write) Descripti on AmountBIOS.ProcSettings.Proc2L2Cache (Read Only) of memory in the corresponding processor cache. Legal Values None Default Value Not Applicable Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Depende ncy None BIOS.ProcSettings.Proc2L3Cache (Read or Write) Descripti on Amount of memory in the corresponding processor cache.
BIOS.ProcSettings.Proc2NumCores (Read or Write) Descripti on Number of cores in the processor package. Legal Values None Default Value Not Applicable Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Depende ncy None BIOS.ProcSettings.Proc3Brand (Read or Write) Descripti on Brand text provided by the processor manufacturer.
NOTE: You can enable this option only when System Profile is set to Performance. Legal Values • • • • • Default Value Not Applicable Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Depende ncy None Disabled ControlledTurboLimit ControlledTurboLimitMinus1 ControlledTurboLimitMinus2 ControlledTurboLimitMinus3 BIOS.ProcSettings.Proc3Id (Read or Write) Descripti on Processor's family model and stepping values.
BIOS.ProcSettings.Proc3L2Cache (Read or Write) Descripti on Amount of memory in the corresponding processor cache. Legal Values None Default Value Not Applicable Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Depende ncy None BIOS.ProcSettings.Proc3L3Cache (Read or Write) Descripti on Amount of memory in the corresponding processor cache.
Default Value Not Applicable Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Depende ncy None BIOS.ProcSettings.Proc4Brand (Read or Write) Descripti on The processor manufacturer provides brand text Legal Values None Default Value Not Applicable Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Depende ncy None BIOS.ProcSettings.Proc4ControlledTurbo (Read or Write) Descripti on Controls the turbo engagement.
Default Value Not Applicable Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Depende ncy Not Applicable BIOS.ProcSettings.Proc4Id (Read or Write) Descripti on Processor's family model and stepping values. Legal Values None Default Value Not Applicable Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Depende ncy None BIOS.ProcSettings.
Depende ncy None BIOS.ProcSettings.Proc4L3Cache (Read or Write) Descripti on Amount of memory in the corresponding processor cache. Legal Values None Default Value Not Applicable Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Depende ncy None BIOS.ProcSettings.Proc4NumCores (Read or Write) Descripti on Number of cores in the processor package.
BIOS.ProcSettings.Proc64bit (Read or Write) Descripti on Specifies whether the installed processors support 64-bit extensions. Legal Values None Default Value Not Applicable Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Depende ncy None BIOS.ProcSettings.ProcAdjCacheLine (Read or Write) Descripti on Enables or disables the system optimization for applications that require high utilization of sequential memory access.
BIOS.ProcSettings.ProcBusSpeed (Read or Write) Descripti on Bus speed of the processor. Legal Values None Default Value Not Applicable Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Depende ncy None BIOS.ProcSettings.ProcConfigTdp (Read or Write) Descripti on Allows to re-configure the Thermal Design Power (TDP) to lower levels.
BIOS.ProcSettings.ProcCores (Read or Write) Descripti on Controls the number of enabled cores in each processor. Legal Values • • • • • • • • • • • Default Value Not Applicable Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Depende ncy None Single All 1 2 4 6 8 10 12 14 16 BIOS.ProcSettings.ProcCoreSpeed (Read or Write) Descripti on Clock speed of the processor.
Depende ncy None BIOS.ProcSettings.ProcDramPrefetcher (Read or Write) Descripti on Enable to turn on the DRAM prefetch unit in the Northbridge. Disable to prevent DRAM references from triggering DRAM prefetch requests. Legal Values • • Default Value Not Applicable Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Depende ncy None Enabled Disabled BIOS.ProcSettings.
BIOS.ProcSettings.ProcHpcMode (Read or Write) Descripti on Configure processor's HPC mode. Legal Values • • Default Value Not Applicable Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Depende ncy None Enabled Disabled BIOS.ProcSettings.ProcHtAssist (Read or Write) Descripti on When enabled it provides filtering of broadcast probes to improve HyperTransport I/O Link bandwidth and performance on multi-node systems.
BIOS.ProcSettings.ProcHwPrefetcher (Read or Write) Descripti on When enabled, the processor is able to prefetch extra cache lines for every memory request. Legal Values • • Default Value Not Applicable Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Depende ncy None Enabled Disabled BIOS.ProcSettings.ProcHyperTransport (Read or Write) Descripti on Specifies the supported HyperTransport I/O Link Specification.
BIOS.ProcSettings.ProcSoftwarePrefetcher (Read or Write) Descripti on Enables or disables the hardware prefetcher for considering software prefetches when detecting strides for prefetch requests. Legal Values • • Default Value Not Applicable Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Depende ncy None Enabled Disabled BIOS.ProcSettings.
BIOS.ProcSettings.ProcX2Apic (Read or Write) Descripti on Enables or disables the X2APIC mode. Legal Values • • Default Value Disabled Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Depende ncy None Enabled Disabled BIOS.ProcSettings.QpiBandwidthPriority (Read or Write) Descripti on Sets the bandwidth priority to compute (default) or I/O.
BIOS.ProcSettings.QpiSpeed (Read or Write) Descripti on Controls QuickPath Interconnect data rate settings. Legal Values • • • • Default Value Not Applicable Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Depende ncy None MaxDataRate 8 GTps 7 GTps 6 GTps BIOS.ProcSettings.RtidSetting (Read or Write) Descripti on Allocates more RTIDs to the remote socket increasing cache performance between the sockets.
BIOS.ProxyAttributes The objects in this group manage the legacy boot protocol of LOM. BIOS.ProxyAttributes.EmbNicPortnBootproto (Read or Write) Descripti on Controls the Legacy Boot Protocol of the LOM port specified by the Embedded NIC port. Assists in system management software and does not appear in system BIOS setup. The value of n can be 1–4. This attribute returns Unknown when read. The LOM port legacy boot protocol setting is not changed when Unknown is written.
An error is returned if written with a setting (None, PXE, or iSCSI) that is not supported by the LOM. Legal Values • • • • Default Value Not Applicable Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Depende ncy None Unknown None Pxe Iscsi BIOS.PxeDevice1Settings The objects in this group manage the PXE device settings. BIOS.PxeDevice1Settings.PxeDevnInterface (Read or Write) Descripti on Indicates the NIC Interface used for the specified PXE device.
BIOS.PxeDevice1Settings.PxeDevnProtocol (Read or Write) Descripti on Controls the PXE protocol used for the specified PXE device. For the attribute PxeDevnProtocol, the value of n can be 1 — 4. Legal Values • • Default Value None Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Depende ncy None IPv4 IPv6 BIOS.PxeDevice1Settings.PxeDevnVlanEnDis (Read or Write) Descripti on Indicates if the VLAN is enabled or disabled for the specified PXE device.
BIOS.PxeDevice1Settings.PxeDevnVlanId (Read or Write) Descripti on Indicates the VLAN ID for the specified PXE device. For the attribute PxeDevnVlanId, the value of n can be 1 — 4. Legal Values None Default Value Not Applicable Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Depende ncy None BIOS.PxeDevice1Settings.PxeDevnVlanPriority (Read or Write) Descripti on Indicates the VLAN priority for the specific PXE device.
BIOS.SataSettings.eSataPort1 (Read or Write) Descripti on Sets the drive type of the selected device. Legal Values • • Default Value Not Applicable Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Depende ncy None Off Auto BIOS.SataSettings.eSataPort1Capacity (Read or Write) Descripti on Displays the total capacity of a hard-disk drive.
Default Value Not Applicable Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Depende ncy None BIOS.SataSettings.eSataPort1Model (Read or Write) Descripti on Displays the drive model of the selected device. Legal Values None Default Value Not Applicable Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Depende ncy None BIOS.SataSettings.SataPortA (Read or Write) Descripti on Sets the drive type of the selected device.
Depende ncy Read Only if EmbSata is not set to AtaMode. BIOS.SataSettings.SataPortACapacity (Read or Write) Descripti on Displays the total capacity of a hard-disk drive. Legal Values None Default Value Not Applicable Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Depende ncy None BIOS.SataSettings.SataPortADriveType (Read or Write) Descripti on Indicates type of device attached to this SATA port.
BIOS.SataSettings.SataPortAModel (Read or Write) Descripti on Displays the drive model of the selected device. Legal Values None Default Value Not Applicable Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Depende ncy None BIOS.SataSettings.SataPortB (Read or Write) Descripti on Sets the drive type of the selected device.
Default Value Not Applicable Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Depende ncy None BIOS.SataSettings.SataPortBDriveType (Read or Write) Descripti on Indicates type of device attached to this SATA port. Legal Values None Default Value Not Applicable Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Depende ncy None BIOS.SataSettings.
Depende ncy None BIOS.SataSettings.SataPortC (Read or Write) Descripti on Sets the drive type of the selected device. Legal Values • • Default Value Not Applicable Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Depende ncy Read Only if EmbSata is not set to AtaMode. Off Auto BIOS.SataSettings.SataPortCCapacity (Read or Write) Descripti on Displays the total capacity of a hard-disk drive.
BIOS.SataSettings.SataPortCDriveType (Read or Write) Descripti on Indicates type of device attached to this SATA port. Legal Values None Default Value Not Applicable Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Depende ncy None BIOS.SataSettings.SataPortCModel (Read or Write) Descripti on Displays the drive model of the selected device.
Default Value Not Applicable Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Depende ncy Read Only if EmbSata is not set to AtaMode. BIOS.SataSettings.SataPortDCapacity (Read or Write) Description Displays the total capacity of a hard-disk drive. Legal Values None Default Value Not Applicable Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Dependency None BIOS.SataSettings.
BIOS.SataSettings.SataPortDModel (Read or Write) Description Displays the drive model of the selected device. Legal Values None Default Value Not Applicable Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Dependency None BIOS.SataSettings.SataPortE (Read or Write) Description Sets the drive type of the selected device.
Dependency None BIOS.SataSettings.SataPortEDriveType (Read or Write) Description Indicates type of device attached to this SATA port. Legal Values None Default Value Not Applicable Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Dependency None BIOS.SataSettings.SataPortEModel (Read or Write) Description Displays the drive model of the selected device.
License Required iDRAC Express or iDRAC Enterprise Dependency Read Only if EmbSata is not set to AtaMode. BIOS.SataSettings.SataPortFCapacity (Read or Write) Description Displays the total capacity of a hard-disk drive. Legal Values None Default Value Not Applicable Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Dependency None BIOS.SataSettings.SataPortFDriveType (Read or Write) Description Indicates type of device attached to this SATA port.
License Required iDRAC Express or iDRAC Enterprise Dependency None BIOS.SataSettings.SataPortG (Read or Write) Description Sets the drive type of the selected device. Legal Values • • Default Value Not Applicable Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Dependency Read Only if EmbSata is not set to AtaMode. Off Auto BIOS.SataSettings.SataPortGCapacity (Read or Write) Description Displays the total capacity of a hard-disk drive.
Default Value Not Applicable Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Depende ncy None BIOS.SataSettings.SataPortGModel (Read or Write) Descripti on Displays the drive model of the selected device. Legal Values None Default Value Not Applicable Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Depende ncy None BIOS.SataSettings.SataPortH (Read or Write) Descripti on Sets the drive type of the selected device.
Depende ncy Read Only if EmbSata is not set to AtaMode. BIOS.SataSettings.SataPortHCapacity (Read or Write) Descripti on Displays the total capacity of a hard disk drive. Legal Values None Default Value Not Applicable Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Depende ncy None BIOS.SataSettings.SataPortHDriveType (Read or Write) Descripti on Indicates type of device attached to this SATA port.
BIOS.SataSettings.SataPortHModel (Read Only) Descripti on Displays the drive model of the selected device. Legal Values None Default Value Not Applicable Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Depende ncy None BIOS.SataSettings.SataPortI (Read or Write) Descripti on Sets the drive type of the selected device. When the Embedded SATA setting is in: • ATA Mode, setting this attribute to Auto will enable the BIOS support for the device.
BIOS.SataSettings.SataPortICapacity (Read or Write) Descripti on Displays the total capacity of a hard-disk drive. This property is not defined for removable-media devices such as optical drives. Legal Values Not Applicable Default Value Not Applicable Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Depende ncy None BIOS.SataSettings.SataPortIDriveType (Read or Write) Descripti on Indicates the type of device attached to this SATA port.
Default Value Not Applicable Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Depende ncy None BIOS.SataSettings.SataPortJ (Read or Write) Descripti on Sets the drive type of the selected device. When the Embedded SATA setting is in: • ATA Mode, set this property to Auto to enable the BIOS support for the device. Select Off to turn off the BIOS support for the device. • AHCI Mode or RAID Mode, the BIOS always enables support for the device.
Default Value Not Applicable Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Depende ncy None BIOS.SataSettings.SataPortJDriveType (Read or Write) Descripti on Indicates the type of device attached to this SATA port. Legal Values Not Applicable Default Value Not Applicable Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Depende ncy None BIOS.SataSettings.
Depende ncy None BIOS.SataSettings.SecurityFreezeLock (Read or Write) Descripti on Directs the Security Freeze Lock command to the Embedded SATA drives during POST. This option is only applicable for ATA and AHCI mode, and not applicable for RAID mode. Legal Values • • Default Value Not Applicable Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Depende ncy None Enabled Disabled BIOS.
Depende ncy None BIOS.SerialCommSettings.ExtSerialConnector (Read or Write) Descripti on Associate the External Serial Connector to Serial 1 or Serial 2 or Remote Access Device. Legal Values • • • Default Value Not Applicable Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Depende ncy None Serial1 Serial2 RemoteAccDevice BIOS.SerialCommSettings.FailSafeBaud (Read or Write) Descripti on BIOS attempts to determine the baud rate automatically.
Depende ncy None BIOS.SerialCommSettings.RedirAfterBoot (Read or Write) Descripti on Enables or disables the BIOS console redirection when the operating system is loaded. Legal Values • • Default Value Not Applicable Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Depende ncy None Enabled Disabled BIOS.SerialCommSettings.SerialComm (Read or Write) Descripti on Controls the serial communication options.
BIOS.SerialCommSettings.SerialPortAddress (Read or Write) Descripti on Port address for the Serial Devices. (COM1=0x3F8 COM2=0x2F8) Legal Values • • • • Default Value Not Applicable Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Depende ncy None Serial1Com1Serial2Com2 Serial1Com2Serial2Com1 Com1 Com2 BIOS.SlotDisablement To manage the slot disablement settings, use the objects in this group. BIOS.SlotDisablement.
Depende ncy None BIOS.SlotDisablement.Slot2 (Read or Write) Descripti on Control the configuration of the card installed in slot 2. Legal Values • • • Default Value Not Applicable Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Depende ncy None Enabled Disabled BootDriverDisabled BIOS.SlotDisablement.Slot3 (Read or Write) Descripti on Control the configuration of the card installed in slot 3.
BIOS.SlotDisablement.Slot4 (Read or Write) Descripti on Control the configuration of the card installed in slot 4. Legal Values • • • Default Value Not Applicable Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Depende ncy None Enabled Disabled BootDriverDisabled BIOS.SlotDisablement.Slot5 (Read or Write) Descripti on Control the configuration of the card installed in slot 5.
BIOS.SlotDisablement.Slot6 (Read or Write) Descripti on Control the configuration of the card installed in slot 6. Legal Values • • • Default Value Not Applicable Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Depende ncy None Enabled Disabled BootDriverDisabled BIOS.SlotDisablement.Slot7 (Read or Write) Descripti on Control the configuration of the card installed in slot 7.
BIOS.SlotDisablement.Slot8 (Read or Write) Descripti on Controls configuration of the card installed in this slot. You can set one of the following options for each card: • • • Enabled: The card is available during POST or to the operating system. Disabled: The card is not available during POST or to the operating system. Boot Driver Disabled: The Option ROM is not run during POST, the system cannot boot from the card, and the preboot services are not available.
boot services are not available. However, it is available to the operating system. This option is not available if the slot contains a Dell RAID card. NOTE: If multiple cards from the same manufacturer are managed using the same boot driver, select BootDriverDisabled for all the cards from the same manufacturer so that the Option ROM is not run.
NOTE: If multiple cards from the same manufacturer are managed using the same boot driver, select BootDriverDisabled value for all the cards from the same manufacturer so that the Option ROM is not run. Legal Values • • • Default Value Not Applicable Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Depende ncy None Enabled Disabled BootDriverDisabled BIOS.SysInformation To view information about system configuration, use the objects in this group. BIOS.
BIOS.SysInformation.SystemBiosVersion (Read or Write) Descripti on Provides the current revision of the system BIOS firmware. Legal Values None Default Value Not Applicable Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Depende ncy None BIOS.SysInformation.SystemCpldVersion (Read or Write) Descripti on Displays the current revision of the system CPLD firmware.
BIOS.SysInformation.SystemManufacturer (Read or Write) Descripti on Provides the name of the Original Equipment Manufacturer of this system. Legal Values None Default Value Not Applicable Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Depende ncy None BIOS.SysInformation.SystemModelName (Read or Write) Descripti on Provides the product name of the system.
BIOS.SysInformation.SystemServiceTag (Read or Write) Descripti on The Service Tag assigns the Original Equipment Manufacturer of this system. Legal Values None Default Value Not Applicable Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Depende ncy` None BIOS.SysInformation.UefiComplianceVersion (Read or Write) Descripti on Displays the system firmware UEFI compliance level.
BIOS.SysProfileSettings.CollaborativeCpuPerfCtrl (Read/ Write) Descripti on Enables or disables the CPU power management control. When ProcPwrPerf is not set to SysDbpm in Custom mode, changing this setting does not affect system performance. Legal Values • • Default Value Not Applicable Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Depende ncy Enabled only when SysProfileSettings.ProcPwrPerf is set to SysDbpm in Custom mode. Enabled Disabled BIOS.
BIOS.SysProfileSettings.EnergyPerformanceBias (Read or Write) Descripti on Indicates the energy performance settings. Legal Values • MaxPower • BalancedPerformance • BalancedEfficiency • LowPower Default Value Not Applicable Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Depende ncy None BIOS.SysProfileSettings.MemFrequency (Read or Write) Descripti on Set the speed of the system memory to maximum performance, maximum reliability or a specific speed.
Depende ncy Read Only if SysProfileSettings.SysProfile is not set to Custom mode. BIOS.SysProfileSettings.MemPatrolScrub (Read or Write) Descripti on Patrol scrubbing is a feature that searches the memory for errors and repairs correctable errors to prevent the accumulation of memory errors. Legal Values • • • Default Value Not Applicable Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Depende ncy Read Only if SysProfileSettings.
BIOS.SysProfileSettings.MemRefreshRate (Read or Write) Descripti on Frequency at which memory is normally refreshed. Legal Values • • Default Value Not Applicable Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Depende ncy Read Only if SysProfileSettings.SysProfile is not set to Custom mode. 1x 2x BIOS.SysProfileSettings.MemVolt (Read or Write) Descripti on Sets the DIMM voltage selection.
BIOS.SysProfileSettings.MonitorMwait (Read or Write) Descripti on Enables or disables Monitor or Mwait instructions. When C state is enabled in Custom mode, changing this setting does not affect system performance Legal Values • • Default Value Not Applicable Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Depende ncy Disabled only when SysProfileSettings.ProcCStates state is disabled in Custom mode. Enabled Disabled BIOS.SysProfileSettings.
BIOS.SysProfileSettings.ProcC1E (Read or Write) Descripti on When enabled, the processor is allowed to switch to minimum performance state when idle. Legal Values • • Default Value Not Applicable Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Depende ncy Read Only if SysProfileSettings.SysProfile is not set to Custom mode. Enabled Disabled BIOS.SysProfileSettings.ProcCStates (Read or Write) Descripti on Enables or disables the processor C-States.
BIOS.SysProfileSettings.ProcPwrPerf (Read or Write) Descripti on Sets CPU power management to maximum performance operating system DBPM or System DBPM (DAPC) mode. Legal Values • • • • Default Value Not Applicable Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Depende ncy Read Only if SysProfileSettings.SysProfile is not set to Custom mode. MaxPerf MinPwr SysDbpm OsDbpm BIOS.SysProfileSettings.
BIOS.SysProfileSettings.SysProfile (Read or Write) Descripti on Sets the System Profile to Performance Per Watt (DAPC), Performance Per Watt (OS) Performance Dense Configuration, or Custom mode. Legal Values • • • • • Default Value Not Applicable Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Depende ncy None PerfPerWattOptimizedOs PerfPerWattOptimizedDapc PerfOptimized Custom DenseCfgOptimized BIOS.SysProfileSettings.
Default Value Not Applicable Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Depende ncy None BIOS.SysProfileSettings.UncoreFrequency (Read or Write) Descripti on Selects the processor uncore frequency. Legal Values • • • Default Value Not Applicable Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Depende ncy None DynamicUFS MaxUFS MinUFS BIOS.
BIOS.SysSecurity.AcPwrRcvry (Read or Write) Descripti on Specifies how the system responds after AC power is restored to the system. It is useful when the system is turned off with a power strip. Legal Values • • • Default Value Not Applicable Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Depende ncy Read Only if SysSecurity.AcPwrRcvry is set to Off. On Off Last BIOS.SysSecurity.
BIOS.SysSecurity.AcPwrRcvryUserDelay (Read or Write) Descripti on Controls the user-defined AC Recovery Delay. Legal Values None Default Value Not Applicable Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Depende ncy None BIOS.SysSecurity.Aesni (Read or Write) Descripti on Displays the status of Intel(R) Processor AES-NI feature.
UEFI shell based flash utilities, or Lifecycle Controller user interface is disallowed. Legal Values • • • Default Value Not Applicable Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Depende ncy None Unlocked Limited Locked BIOS.SysSecurity.IntelTxt (Read or Write) Descripti on Enables or disables Trusted Execution technology.
BIOS.SysSecurity.NmiButton (Read or Write) Descripti on Enables or disables the NMI button on the front panel. Legal Values • • Default Value Not Applicable Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Depende ncy None Enabled Disabled BIOS.SysSecurity.PasswordStatus (Read or Write) Descripti on Locks the system password.
BIOS.SysSecurity.PwrButton (Read or Write) Descripti on Enables or disables the power button on the front panel. Legal Values • • Default Value Not Applicable Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Depende ncy None Enabled Disabled BIOS.SysSecurity.SecureBoot (Read or Write) Descripti on Enables or disables the SecureBoot option.
BIOS.SysSecurity.SetupPassword (Read or Write) Descripti on Set up the system password. Optional parameter –o is used with this object to provide old password as an authentication for changing the previously configured password to the new password. The password can include the following: • Up to 32 characters including whitespace. • Contain numbers 0 through 9. • Only lower case alphabets are accepted. • Special characters accepted are +, ",,, — , ., /, ;, [, \, ], `.
License Required iDRAC Express or iDRAC Enterprise Depende ncy None BIOS.SysSecurity.SHA256SetupPasswordSalt (Read or Write) Descripti on Indicates the Salt string added to the setup password before hash. Legal Values String of 32 characters Default Value Not Applicable Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Depende ncy None BIOS.SysSecurity.SignedFirmwareUpdate (Read or Write) Descripti on Enables the signed BIOS update feature.
BIOS.SysSecurity.SysPassword (Read or Write) Descripti on Provides the system password. Optional parameter –o is used with this object to provide old password as an authentication for changing the previously configured password to the new password. The password can include the following: • Up to 32 characters including whitespace. • Contain numbers 0 through 9. • Only lower case alphabets are accepted. • Special characters accepted are +, ", ,, -, ., /, ;, [, \, ], `.
Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Depende ncy None BIOS.SysSecurity.SHA256SystemPasswordSalt (Read or Write) Descripti on Indicates the Salt string added to the system password before hash. Legal Values String of 32 characters Default Value Not Applicable Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Depende ncy None BIOS.SysSecurity.
Depende ncy None BIOS.SysSecurity.TcmClear (Read or Write) Descripti on Warns that clearing the TPM causes loss of all keys in the TPM. It may affect starting the operating system. Legal Values • • Default Value Not Applicable Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Depende ncy None Yes No BIOS.SysSecurity.TcmSecurity (Read or Write) Descripti on Controls the reporting of the Trusted Cryptography Module (TCM) in the system.
BIOS.SysSecurity.TpmActivation (Read or Write) Descripti on Specify the operational state of the Trusted Platform Module (TPM). Legal Values • • • Default Value Not Applicable Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Depende ncy Read Only if SysSecurity.TpmSecurity is set to Off. NoChange Activate Deactivate BIOS.SysSecurity.TpmClear (Read or Write) Descripti on Warns that clearing the TPM causes loss of all keys in the TPM.
BIOS.SysSecurity.TpmSecurity (Read or Write) Descripti on Controls the reporting of the Trusted Platform Module (TPM) in the system. Legal Values • • • Default Value Not Applicable Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Depende ncy None Off OnPbm OnNoPbm BIOS.SysSecurity.TPMStatus (Read Only) Descripti on Displays the status of TPM. Legal Values String of up to 64 ASCII characters.
BIOS.UefiBootSettings.UefiBootSeq (Read or Write) Descripti on Controls the UEFI boot order. The first option in the list is tried first. If unsuccessful, the second option is tried and so on. This property is applied only when Boot Mode is UEFI and not BIOS. Legal Values Enum Values Default Value Not Applicable Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Depende ncy None BIOS.UefiBootSettings.
FC.FCDevice The objects in this group manage the FC device. FC.FCDevice.BusDeviceFunction (Read Only) Descripti on Indicates the enumerated PCI Bus, Device, and Function value as a single string. Legal Values Not Applicable Default Value Not Applicable Write Privilege Not Applicable License Required iDRAC Express or iDRAC Enterprise Depende ncy Not Applicable FC.FCDevice.ChipMdl (Read Only) Descripti on Indicates the PCI configuration space information.
FC.FCDevice.EFIVersion (Read Only) Descripti on Indicates the version of the EFI device driver. Legal Values Not Applicable Default Value Not Applicable Write Privilege Not Applicable License Required iDRAC Express or iDRAC Enterprise Depende ncy Not Applicable FC.FCDevice.FamilyVersion (Read Only) Descripti on Indicates the firmware’s family version.
Default Value Not Applicable Write Privilege Not Applicable License Required iDRAC Express or iDRAC Enterprise Depende ncy Not Applicable FC.FCTarget The objects in this group manage the Fibre Channel target. FC.FCTarget.BootScanSelection (Read or Write) Descripti on Sets the port’s operation while starting the system from Fiber Channel target(s). Only operations supported by the optionROM should be implemented.
FC.FCTarget.FirstFCTargetLUN (Read or Write) Descripti on Specifies the LUN (Logical Unit Number) of the first Fibre Channel boot target. Legal Values Not Applicable Default Value Not Applicable Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Depende ncy Not Applicable FC.FCTarget.SecondFCTargetLUN (Read or Write) Descripti on Specifies the LUN of the second Fibre Channel boot target.
Default Value Not Applicable Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Depende ncy Not Applicable FC.FCTarget.SecondFCTargetWWPN (Read or Write) Descripti on Specifies the World Wide Port Name (WWPN) of the second Fibre Channel boot target. Legal Values Not Applicable Default Value Not Applicable Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Depende ncy Not Applicable FC.
Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Depende ncy Not Applicable FC.HBAConfig.FabricLoginTimeout (Read or Write) Descripti on Sets the SAN Fabric login time out. Legal Values Not Applicable Default Value 3000 Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Depende ncy Not Applicable FC.HBAConfig.FabricLoginRetryCount (Read or Write) Descripti on Sets the current SAN Fabric login retry count.
FC.HBAConfig.FramePayloadSize (Read or Write) Descripti on Sets the Frame Payload Size to automatic or in bytes. Legal Values • Auto • 512 • 1024 • 2048 • 2112 Default Value Auto Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Depende ncy Not Applicable FC.HBAConfig.HardZone (Read or Write) Descripti on Enables or disables the Fibre Channel hard zone.
FC.HBAConfig.HardZoneAddress (Read or Write) Descripti on Sets the Hard Zone address. Legal Values Not Applicable Default Value 0 Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Depende ncy Not Applicable FC.HBAConfig.LinkDownTimeout (Read or Write) Descripti on Sets the Link down time out. Legal Values Not Applicable Default Value 3000 Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Depende ncy Not Applicable FC.
Default Value 5 Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Depende ncy Not Applicable FC.HBAConfig.PortDownRetryCount (Read or Write) Descripti on Sets the target port down Input/Output retry count. Legal Values Not Applicable Default Value Not Applicable Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Depende ncy Not Applicable FC.HBAConfig.
Depende ncy Not Applicable FC.HBAConfig.PortLoginRetryCount (Read or Write) Descripti on Sets the target Port login retry count. Legal Values Not Applicable Default Value 3 Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Depende ncy Not Applicable FC.HBAConfig.PortLoginTimeout (Read or Write) Descripti on Sets the target port login time out.
FC.PortConfig.DeviceName (Read Only) Descripti on Indicates the product name of the Fibre Channel host bus adapter. Legal Values Not Applicable Default Value Not Applicable Write Privilege Not Applicable License Required iDRAC Express or iDRAC Enterprise Depende ncy Not Applicable FC.PortConfig.FCDevice (Read Only) Descripti on Displays the version of the device and firmware.
Default Value Not Applicable Write Privilege Not Applicable License Required iDRAC Express or iDRAC Enterprise Depende ncy Not Applicable FC.PortConfig.HBAConfig (Read Only) Descripti on Configures the advanced settings for adapter and port. Legal Values Not Applicable Default Value Not Applicable Write Privilege Not Applicable License Required iDRAC Express or iDRAC Enterprise Depende ncy Not Applicable FC.PortConfig.
Depende ncy Not Applicable FC.PortConfig.PortSpeed (Read or Write) Descripti on Specifies the data rate of the Fibre Channel Host Bus Adapter port. The value can be Automatic or specified in Gbps. Legal Values • Auto • 1G • 2G • 4G • 8G • 16G Default Value Auto Write Privilege Sever Control License Required iDRAC Express or iDRAC Enterprise Depende ncy Not Applicable FC.PortConfig.
Depende ncy Not Applicable FC.PortConfig.VirtualWWPN (Read or Write) Descripti on Indicates the virtual Fibre Channel World Wide Port Name of the port. Legal Values Not Applicable Default Value Not Applicable Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Depende ncy Not Applicable FC.PortConfig.WWN (Read Only) Descripti on Indicates the permanent Fibre Channel World Wide Node name.
FC.PortConfig.WWPN (Read Only) Descripti on Indicates the permanent Fibre Channel World Wide Port Name assigned to the port. Legal Values Not Applicable Default Value Not Applicable Write Privilege Not Applicable License Required iDRAC Express or iDRAC Enterprise Depende ncy Not Applicable NIC.ConfigureFormn The objects in this group manage. NIC.ConfigureFormn.BusDeviceFunction (Read Only) Descripti on Indicates the value of the bus device function.
NIC.ConfigureFormn.MacAddr (Read Only) Descripti on Indicates the permanent MAC address. Legal Values Not Applicable Default Value Not Applicable Write Privilege Not Applicable License Required iDRAC Express or iDRAC Enterprise Depende ncy Not Applicable NIC.ConfigureFormn.FIPMacAddr (Read Only) Descripti on Indicates the permanent FIP-MAC address for FCoE.
Default Value Not Applicable Write Privilege Not Applicable License Required iDRAC Express or iDRAC Enterprise Depende ncy Not Applicable NIC.ConfigureFormn.iScsiOffloadMode (Read or Write) Descripti on Enables or disables the iSCSI off load on the partition. Legal Values • Enabled • Disabled Default Value Disabled Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Depende ncy Not Applicable NIC.ConfigureFormn.
Depende ncy Not Applicable NIC.ConfigureFormn.NicMode (Read or Write) Descripti on Enables or disables the NIC mode on the partition. Legal Values • Enabled • Disabled Default Value Disabled Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Depende ncy Not Applicable NIC.ConfigureFormn.PCIDeviceID (Read Only) Descripti on Indicates the PCI Device ID of the partition.
NIC.ConfigureFormn.WWN (Read Only) Descripti on Indicates the Fibre Channel World Wide Node name identifier for FCoE. Legal Values Not Applicable Default Value Not Applicable Write Privilege Not Applicable License Required iDRAC Express or iDRAC Enterprise Depende ncy Not Applicable NIC.ConfigureFormn.WWPN (Read Only) Descripti on Indicates the Fibre Channel World Wide Port Name identifier for FCoE.
NIC.ConfigureFormn.VirtWWN (Read or Write) Descripti on Sets the Fibre Channel World Wide Node Name identifier for partition FCoE. Legal Values Not Applicable Default Value 00:00:00:00:00:00:00:00 Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Depende ncy Not Applicable NIC.ConfigureFormn.VirtWWPN (Read or Write) Descripti on Assigns the Fibre Channel World Wide Port Name identifier for partition FCoE.
Default Value 00:00:00:00:00:00 Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Depende ncy Not Applicable NIC.ConfigureFormn.VirtIscsiMacAddr (Read or Write) Descripti on Assigns the MAC address for partition iSCSI off load. Legal Values Not Applicable Default Value 00:00:00:00:00:00 Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Depende ncy Not Applicable NIC.ConfigureFormn.
Depende ncy Not Applicable NIC.DCBSettings The following section provides information about the objects in the NIC.DCBSettings group. NIC.DCBSettings.CongestionNotification (Read Only) Descripti on Indicates whether Congestion Notification capability is supported. Legal Values • • Default Value Not Applicable Write Privilege Not Applicable License Required iDRAC Express or iDRAC Enterprise Depende ncy None Available Unavailable NIC.DCBSettings.
Depende ncy None NIC.DCBSettings.EnhancedTransmissionSelection (Read Only) Descripti on Indicates whether Enhanced Transmission Selection capability is supported. Legal Values • • Default Value Not Applicable Write Privilege Not Applicable License Required iDRAC Express or iDRAC Enterprise Depende ncy None Available Unavailable NIC.DCBSettings.PriorityFlowControl (Read Only) Descripti on Indicates whether Priority Flow Control capability is supported.
NIC.DeviceLevelConfig To manage the device level configurations, use the objects in this group. NIC.DeviceLevelConfig.EVBModesSupport (Read Only) Descripti on Indicates the type of EVB Modes supported. Legal Values • • • • Default Value Not Applicable Write Privilege Not Applicable License Required iDRAC Express or iDRAC Enterprise Depende ncy None VEB VEPA PE Multichannel NIC.DeviceLevelConfig.FlowControlSetting (Read or Write) Descripti on Configure type of Flow Control used.
License Required iDRAC Express or iDRAC Enterprise Depende ncy None NIC.DeviceLevelConfig.NParEP (Read or Write) Descripti on Controls the enablement of NParEP mode. Legal Values • Enabled • Disabled Default Value Disabled Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Depende ncy Not Applicable NIC.DeviceLevelConfig.SRIOVSupport (Read Only) Descripti on Indicates whether SR-IOV capability is supported.
NIC.DeviceLevelConfig.VirtualizationMode (Read or Write) Descripti on Specifies the type of virtualization used by the controller on all ports. Legal Values • NONE • NPAR • SRIOV • NPARSRIOV Default Value None Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Depende ncy Not Applicable NIC.FCOECapabilities The following section provides information about the objects in the NIC.FCOECapabilities group. NIC.FCOECapabilities.
License Required iDRAC Express or iDRAC Enterprise Depende ncy None NIC.FCOECapabilities.MaxFrameSize (Read Only) Descripti on Indicates the maximum frame size for each FCoE frame. Legal Values None Default Value Not Applicable Write Privilege Not Applicable License Required iDRAC Express or iDRAC Enterprise Depende ncy None NIC.FCOECapabilities.MaxIOsPerSession (Read Only) Descripti on Indicates the maximum number of IOs supported per session.
NIC.FCOECapabilities.MaxNPIVPerPort (Read Only) Descripti on Indicates the maximum number of NPIV WWN per port. Legal Values None Default Value Not Applicable Write Privilege Not Applicable License Required iDRAC Express or iDRAC Enterprise Depende ncy None NIC.FCOECapabilities.MaxNumberExchanges (Read Only) Descripti on Indicates the maximum number of exchanges supported.
Default Value Not Applicable Write Privilege Not Applicable License Required iDRAC Express or iDRAC Enterprise Depende ncy None NIC.FCOECapabilities.MaxNumberOfFCTargets (Read Only) Descripti on Indicates the maximum number of FC targets supported. Legal Values None Default Value Not Applicable Write Privilege Not Applicable License Required iDRAC Express or iDRAC Enterprise Depende ncy None NIC.FCOECapabilities.
License Required iDRAC Express or iDRAC Enterprise Depende ncy None NIC.FCOECapabilities.MTUReconfigurationSupport (Read Only) Descripti on Indicates whether the MTU reconfiguration capability is supported. Legal Values • • Default Value Not Applicable Write Privilege Not Applicable License Required iDRAC Express or iDRAC Enterprise Depende ncy None Available Unavailable NIC.FCoEConfiguration The following section provides information about the objects in the NIC.FCoEConfiguration group.
Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Depende ncy None NIC.FCoEConfiguration.BootOrderFirstFCoETarget (Read or Write) Descripti on Specifies the port’s target in the FCoE boot order. Legal Values Not Applicable Default Value 0 Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Depende ncy Not Applicable NIC.FCoEConfiguration.
Depende ncy Not Applicable NIC.FCoEConfiguration.BootOrderThirdFCoETarget (Read or Write) Descripti on Specifies the port's third defined target in the FCoE boot. Legal Values Not Applicable Default Value 0 Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Depende ncy Not Applicable NIC.FCoEConfiguration.BootOrderFourthFCoETarget (Read or Write) Descripti on Specifies the port's fourth defined target in the FCoE boot.
NIC.FCoEConfiguration.FirstFCoEBootTargetLUN (Read or Write) Descripti on LUN of the first FCoE storage target that the FCoE initiator will start the system from when Connect attribute is enabled. Legal Values None Default Value Not Applicable Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Depende ncy Enable FCoEConfiguration.ConnectFirstFCoETarget NIC.FCoEConfiguration.
NIC.FCoEConfiguration.FirstFCoEWWPNTarget (Read or Write) Descripti on World Wide Port Name (WWPN) of the first FCoE storage target. Legal Values None Default Value Not Applicable Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Depende ncy None NIC.FCoEConfiguration.MTUParams (Read or Write) Descripti on Configure the MTU setting.
NIC.FCoEGenParams The following section provides information about the objects in the NIC.FCoEGenParams group. NIC.FCoEGenParams.FCoEBootScanSelection (Read or Write) Descripti on Represents the adaptor behavior for starting the system from specified FCoE storage target or fabric discovered target.
License Required iDRAC Express or iDRAC Enterprise Depende ncy None NIC.FCoEGenParams.FCoEFirstHddTarget (Read or Write) Descripti on Specifies whether the FCoE target is represented as the first HDD to the system. Legal Values • • Default Value Disabled Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Depende ncy None Enabled Disabled NIC.FCoEGenParams.
Depende ncy None NIC.FCoEGenParams.FCoELunBusyRetryCnt (Read or Write) Descripti on Specifies the number of connection retries the FCoE boot initiator will attempt if the FCoE target LUN is busy. Legal Values Values: 0–60 Default Value Not Applicable Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Depende ncy None NIC.FCoEGenParams.FCoETgtBoot (Read or Write) Descripti on Enables the FCoE initiator to start system to the FCoE target.
NIC.FrmwImgMenu The following section provides information about the objects in the NIC.FrmwImgMenu group. NIC.FrmwImgMenu.ControllerBIOSVersion (Read Only) Descripti on Indicates the controller BIOS version information. Legal Values String of up to 8 ASCII characters Default Value Not Applicable Write Privilege Not Applicable License Required iDRAC Express or iDRAC Enterprise Depende ncy None NIC.FrmwImgMenu.
NIC.FrmwImgMenu.FamilyVersion (Read Only) Descripti on Indicates the firmware family version information. Legal Values String of up to 8 ASCII characters Default Value Not Applicable Write Privilege Not Applicable License Required iDRAC Express or iDRAC Enterprise Depende ncy None NIC.GlobalBandwidthAllocation The following section provides information about the objects in the NIC.GlobalBandwidthAllocation group. NIC.GlobalBandwidthAllocation.
NIC.GlobalBandwidthAllocation.MinBandwidth (Read or Write) Descripti on Set the minimum percentage of port TX bandwidth allocated to partition. Legal Values Values: 0–100 Default Value 25 Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Depende ncy None NIC.IscsiFirstTgtParams The following section provides information about the objects in the NIC.IscsiFirstTgtParams group. NIC.IscsiFirstTgtParams.
NIC.IscsiFirstTgtParams.ConnectFirstTgt (Read or Write) Descripti on Enables or disables connecting to the first iSCSI target. Legal Values • • Default Value Disabled Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Depende ncy Not Available if VndrConfigGroup.iSCSIBootSupport is Unavailable. Enabled Disabled NIC.IscsiFirstTgtParams.FirstTgtBootLun (Read or Write) Descripti on Set the first iSCSI storage target boot Logical Unit Number (LUN).
NIC.IscsiFirstTgtParams.FirstTgtChapId (Read or Write) Descripti on Set the first iSCSI storage target Challenge-Handshake Authentication Protocol (CHAP) ID. Legal Values String of up to 128 ASCII characters Default Value Not Applicable Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Depende ncy Not Available if VndrConfigGroup.iSCSIBootSupport is Unavailable. NIC.IscsiFirstTgtParams.
NIC.IscsiFirstTgtParams.FirstTgtIpAddress (Read or Write) Descripti on Set the IP address of the first iSCSI target. Legal Values Valid IPv4 or IPv6 address Default Value Not Applicable Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Depende ncy Not Available if VndrConfigGroup.iSCSIBootSupport is Unavailable. NIC.IscsiFirstTgtParams.FirstTgtIpVer (Read or Write) Descripti on Specifies whether or not IPv4 or IPv6 network address is used for first iSCSI target.
NIC.IscsiFirstTgtParams.FirstTgtIscsiName (Read or Write) Descripti on Set the iSCSI Qualified Name (IQN) of the first iSCSI storage target. Legal Values String of upto 223 ASCII characters Default Value Not Applicable Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Depende ncy Not Available if VndrConfigGroup.iSCSIBootSupport is Unavailable.
NIC.IscsiGenParams The following section provides information about the objects in the NIC.IscsiGenParams group. NIC.IscsiGenParams.ChapAuthEnable (Read or Write) Descripti on To use CHAP authentication when connecting to the iSCSI target, enable or disable the ability of the initiator. Legal Values • • Default Value Disabled Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Depende ncy Not Available if 'VndrConfigGroup.iSCSIBootSupport is Unavailable.
NIC.IscsiGenParams.DhcpVendId (Read or Write) Descripti on Control what Vendor ID is presented to the DHCP service. Legal Values String of upto 255 ASCII characters Default Value Not Applicable Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Depende ncy Not Available if VndrConfigGroup.iSCSIBootSupport is Unavailable. NIC.IscsiGenParams.
NIC.IscsiGenParams.IpAutoConfig (Read or Write) Descripti on Controls the source of the initiator IP address DHCP or static assignment. This option is specific to IPv6. Legal Values • • Default Value Disabled Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Depende ncy Not Available if IscsiGenParams.IpVer is set to 'IPv4' and VndrConfigGroup.iSCSIBootSupport is Unavailable. Enabled Disabled NIC.IscsiGenParams.
NIC.IscsiGenParams.IscsiTgtBoot (Read or Write) Descripti on Specifies whether or not the iSCSI initiator will boot to the specified iSCSI target after connection. Legal Values • Enabled • Disabled • OneTimeDisabled Default Value Disabled Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Depende ncy Not Applicable NIC.IscsiGenParams.IscsiViaDHCP (Read or Write) Descripti on Enables the acquisition of iSCSI target parameters from DHCP.
NIC.IscsiGenParams.IscsiVLanId (Read or Write) Descripti on Specifies the VLAN ID for iSCSI boot mode. Legal Values Not Applicable Default Value Not Applicable Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Depende ncy Not Applicable NIC.IscsiGenParams.IscsiVLanMode (Read or Write) Descripti on Enables or disables the Virtual LAN mode for iSCSI boot.
NIC.IscsiGenParams.LnkUpDelayTime (Read or Write) Descripti on Set the time to allow for link to establish before driver initialization. Legal Values Values from 0 to 255 Default Value 0 Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Depende ncy Not Available if VndrConfigGroup.iSCSIBootSupport is Unavailable. NIC.IscsiGenParams.
NIC.IscsiGenParams.TcpIpViaDHCP (Read or Write) Descripti on Setting to enable acquisition of IPv4 TCP/IP parameters from DHCP. Legal Values • • Default Value Disabled Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Depende ncy Not Available if IscsiGenParams.IpVer is set to 'IPv6' and VndrConfigGroup.iSCSIBootSupport is Unavailable. Enabled Disabled NIC.IscsiGenParams.
NIC.IscsiGenParams.WinHbaBootMode (Read or Write) Descripti on When enabled, it enables iSCSI Offload HBA start mode and disables iSCSI software initiator boot. Legal Values • • Default Value Disabled Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Depende ncy None Enabled Disabled NIC.IscsiInitiatorParams The following section provides information about the objects in the NIC.IscsiInitiatorParams group. NIC.IscsiInitiatorParams.
Depende ncy Not available if VndrConfigGroup.iSCSIBootSupport is unavailable. NIC.IscsiInitiatorParams.IscsiInitiatorChapPwd (Read or Write) Descripti on Set the iSCSI initiator Challenge-Handshake Authentication Protocol (CHAP) secret (password). Legal Values String of 12–16 characters Default Value Not Applicable Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Depende ncy Not available if VndrConfigGroup.iSCSIBootSupport is unavailable. NIC.
NIC.IscsiInitiatorParams.IscsiInitiatorIpAddr (Read or Write) Descripti on Specifies the IP address of the iSCSI initiator. Legal Values String of 2–39 characters (Ipv4 or Ipv6 address) Default Value Not Applicable Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Depende ncy Not available if VndrConfigGroup.iSCSIBootSupport is unavailable. NIC.IscsiInitiatorParams.IscsiInitiatorName (Read or Write) Descripti on Specifies the initiator iSCSI Qualified Name (IQN).
NIC.IscsiInitiatorParams.IscsiInitiatorPrimDns (Read or Write) Descripti on Specifies the Primary DNS IP address of the iSCSI initiator. Legal Values String of 2–39 characters (Ipv4 or Ipv6 gateway) Default Value Not Applicable Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Depende ncy Not available if VndrConfigGroup.iSCSIBootSupport is unavailable. NIC.IscsiInitiatorParams.
NIC.IscsiInitiatorParams.IscsiInitiatorSubnet (Read or Write) Descripti on Specifies the IPv4 Subnet Mask of the iSCSI initiator. Legal Values String of 7–15 characters (IPv4 Subnet) Default Value Not Applicable Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Depende ncy Not available if VndrConfigGroup.iSCSIBootSupport is unavailable. NIC.IscsiInitiatorParams.
NIC.IscsiSecondaryDeviceParams.SecondaryDeviceMacA ddr (Read or Write) Descripti on Specifies the MAC address of a secondary iSCSI boot adapter for redundancy in case if start is unsuccessful. Legal Values String of up to 17 characters Default Value Not Applicable Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Depende ncy Not available if VndrConfigGroup.iSCSIBootSupport is unavailable. NIC.IscsiSecondaryDeviceParams.
NIC.IscsiSecondaryDeviceParams.UseIndTgtPortal (Read or Write) Descripti on Specifies whether to use Independent Target Portal when multipath I/O is enabled. Legal Values • • Default Value Disabled Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Depende ncy Not available if VndrConfigGroup.iSCSIBootSupport is unavailable. Enabled Disabled NIC.IscsiSecondTgtParams To configure the iSCSIsecond storage, use the objects in this group. NIC.IscsiSecondTgtParams.
Depende ncy Not available if VndrConfigGroup.iSCSIBootSupport is unavailable. NIC.IscsiSecondTgtParams.SecondTgtBootLun (Read or Write) Descripti on Specifies the second iSCSI storage target boot Logical Unit Number (LUN). Legal Values Values: 0–18446744073709551615 Default Value Not Applicable Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Depende ncy Not available if VndrConfigGroup.iSCSIBootSupport is unavailable. NIC.IscsiSecondTgtParams.
NIC.IscsiSecondTgtParams.SecondTgtChapPwd (Read or Write) Descripti on Specifies the second iSCSI storage target Challenge-Handshake Authentication Protocol (CHAP) secret (target CHAP password). Legal Values String of 12–16 characters Default Value Not Applicable Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Depende ncy Not available if VndrConfigGroup.iSCSIBootSupport is unavailable. NIC.IscsiSecondTgtParams.
NIC.IscsiSecondTgtParams.SecondTgtIpVer (Read or Write) Descripti on Specifies whether or not IPv4 or IPv4 network address is used for the second iSCSI target. Legal Values • IPv4 • IPv6 Default Value IPv4 Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Depende ncy Not Applicable NIC.IscsiSecondTgtParams.SecondTgtIscsiName (Read or Write) Descripti on Specifies the iSCSI Qualified Name (IQN) of the second iSCSI storage target.
NIC.IscsiSecondTgtParams.SecondTgtTcpPort (Read or Write) Descripti on Specifies the TCP Port number of the second iSCSI target. Legal Values Values: 1–65535 Default Value Not Applicable Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Depende ncy Not available if VndrConfigGroup.iSCSIBootSupport is unavailable. NIC.NICConfig To configure the NICConfig properties, use the objects in this group. NIC.NICConfig.
NIC.NICConfig.BootOptionROM (Read or Write) Descripti on Controls the enablement of legacy Boot Protocols in the Option ROM. Legal Values • Enabled • Disabled Default Value Not Applicable Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Depende ncy Not Applicable NIC.NICConfig.BootRetryCnt (Read or Write) Descripti on Specifies the number of attempts when the start is unsuccessful.
Depende ncy Not Applicable NIC.NICConfig.BootStrapType (Read or Write) Descripti on Specifies the boot strap method used to start the operating system. Legal Values • AutoDetect • BBS • Int18h • Int19h Default Value AutoDetect Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Depende ncy Not Applicable NIC.NICConfig.HideSetupPrompt (Read or Write) Descripti on Enables or disables the option ROM setup prompt during Power On Self Test (POST).
NIC.NICConfig.LegacyBootProto (Read or Write) Descripti on Select a non-UEFI network start protocol. Legal Values • • • • • • Default Value None Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Depende ncy None PXE iSCSI FCoE NONE iSCSIPrimary iSCSI Secondary NIC.NICConfig.LnkSpeed (Read or Write) Descripti on Specifies the port speed used for the selected boot protocol.
Depende ncy None NIC.NICConfig.NumberVFAdvertised (Read or Write) Descripti on Indicates the number of PCI Virtual Functions advertised on the port when SR-IOV is enabled. Legal Values Not Applicable Default Value 0 Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Depende ncy Not Applicable NIC.NICConfig.VLanId (Read or Write) Descripti on Specifies the ID (tag) for the VLAN Mode.
NIC.NICConfig.VLanMode (Read or Write) Descripti on Virtual LAN mode enables use of a VLAN tag to use vendordefined boot protocols. Legal Values • • Default Value Disabled Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Depende ncy None Enabled Disabled NIC.NICConfig.WakeOnLan (Read or Write) Descripti on Enables the server to be powered on using an in-band magic packet.
NIC.NICConfig.WakeOnLanLnkSpeed (Read or Write) Descripti on Select the port speed used for Wake on LAN mode. Legal Values • • • • • Default Value AutoNeg Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Depende ncy None AutoNeg 10 Mbps Half 10 Mbps Full 100 Mbps Half 100 Mbps Full NIC.NICPartitioningConfig To configure the NICPartitioning properties, use the objects in this group. NIC.NICPartitioningConfig.
Depende ncy None NIC.NICPartitioningConfig.PartitionState (Read Only) Descripti on Indicates the current enablement state of the partition. Legal Values • Enabled • Disabled Default Value Enabled Write Privilege Not Applicable License Required iDRAC Express or iDRAC Enterprise Depende ncy Not Applicable NIC.NICPartitioningConfig.ConfigureFormn (Read Only) Descripti on Configures the partition functionality and display the assigned address.
NIC.NICPartitioningConfig.NumberPCIEFunctionsEnable d (Read Only) Descripti on Indicates the number of physical PCIe functions currently enabled on this port. Legal Values Values: 1–65535 Default Value Not Applicable Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Depende ncy None NIC.NICPartitioningConfig.NumberPCIEFunctionsSuppo rted (Read Only) Descripti on Indicates the number of physical PCIe functions supported on this port.
NIC.VndrConfigGroup.BusDeviceFunction (Read Only) Descripti on Indicates the BIOS assigned PCIe. Legal Values String of up to 8 characters Default Value Not Applicable Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Depende ncy None NIC.VndrConfigGroup.BlnkLeds (Read or Write) Descripti on Identifies the physical network port by blinking the associated LED.
Default Value Not Applicable Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Depende ncy None NIC.VndrConfigGroup.EnergyEfficientEthernet (Read Only) Descripti on Indicates whether Energy Efficient Ethernet capability is supported. Legal Values None Default Value Not Applicable Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Depende ncy None NIC.VndrConfigGroup.
License Required iDRAC Express or iDRAC Enterprise Depende ncy None NIC.VndrConfigGroup.DeviceName (Read Only) Descripti on Official product name of the device. Legal Values Not Applicable Default Value Not Applicable Write Privilege Not Applicable License Required iDRAC Express or iDRAC Enterprise Depende ncy Not Applicable NIC.VndrConfigGroup.FCoEBootSupport (Read Only) Descripti on Indicates whether Fibre Channel over Ethernet Boot capability is supported.
NIC.VndrConfigGroup.FCoEOffloadMode (Read or Write) Descripti on Enables or disables FCoE personality on the port. Legal Values • • Default Value Disabled Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Depende ncy None Enabled Disabled NIC.VndrConfigGroup.FCoEOffloadSupport (Read Only) Descripti on Indicates whether FCoE Offload capability is supported.
NIC.VndrConfigGroup.FeatureLicensingSupport (Read Only) Descripti on Indicates whether Dell Feature Licensing capability is supported. Legal Values None Default Value Not Applicable Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Depende ncy None NIC.VndrConfigGroup.FIPMacAddr (Read Only) Descripti on Permanent FIP-MAC address for FCoE assigned during manufacturing.
NIC.VndrConfigGroup.FlexAddressing (Read Only) Descripti on Indicates whether Dell FlexAddressing feature is supported. Legal Values None Default Value Not Applicable Write Privilege Not Applicable License Required iDRAC Express or iDRAC Enterprise Depende ncy None NIC.VndrConfigGroup.iSCSIBootSupport (Read Only) Descripti on Indicates whether iSCSI Boot capability is supported.
Default Value Not Applicable Write Privilege Not Applicable License Required iDRAC Express or iDRAC Enterprise Depende ncy None NIC.VndrConfigGroup.iSCSIOffloadMode (Read or Write) Descripti on Enables or disables iSCSI offload personality on the port. Legal Values • • Default Value Disabled Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Depende ncy None Enabled Disabled NIC.VndrConfigGroup.
Depende ncy None NIC.VndrConfigGroup.LinkStatus (Read Only) Descripti on Indicates the physical network link status that reports the controller. Legal Values None Default Value Not Applicable Write Privilege Not Applicable License Required iDRAC Express or iDRAC Enterprise Depende ncy None NIC.VndrConfigGroup.MacAddr (Read Only) Descripti on Indicates the permanent MAC address assigned during manufacturing.
NIC.VndrConfigGroup.NicMode (Read or Write) Descripti on Enables or disables NIC personality on the port. Legal Values • • Default Value Enabled Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Depende ncy None Enabled Disabled NIC.VndrConfigGroup.NicPartitioningSupport (Read Only) Descripti on Indicates whether NIC Partitioning capability is supported.
NIC.VndrConfigGroup.NWManagementPassThrough (Read Only) Descripti on Indicates whether the Network Management Pass Through capability is supported. Legal Values None Default Value Not Applicable Write Privilege Not Applicable License Required iDRAC Express or iDRAC Enterprise Depende ncy None NIC.VndrConfigGroup.OnChipThermalSensor (Read Only) Descripti on Indicates whether an on-chip thermal sensor is available.
NIC.VndrConfigGroup.OSBMCManagementPassThrough (Read Only) Descripti on Indicates whether OS-BMC Management Pass Through capability is supported. Legal Values None Default Value Not Applicable Write Privilege Not Applicable License Required iDRAC Express or iDRAC Enterprise Depende ncy None NIC.VndrConfigGroup.PCIDeviceID (Read Only) Descripti on Indicates the PCI Device ID of the port.
NIC.VndrConfigGroup.PXEBootSupport (Read Only) Descripti on Indicates whether PXE Boot capability is supported. Legal Values None Default Value Not Applicable Write Privilege Not Applicable License Required iDRAC Express or iDRAC Enterprise Depende ncy None NIC.VndrConfigGroup.RemotePHY (Read Only) Descripti on Indicates whether RemotePHY capability is supported.
Default Value Not Applicable Write Privilege Not Applicable License Required iDRAC Express or iDRAC Enterprise Depende ncy None NIC.VndrConfigGroup.TOESupport (Read Only) Descripti on Indicates whether TCP/IP Offload Engine capability is supported. Legal Values None Default Value Not Applicable Write Privilege Not Applicable License Required iDRAC Express or iDRAC Enterprise Depende ncy None NIC.VndrConfigGroup.
Depende ncy None NIC.VndrConfigGroup.TXBandwidthControlMinimum (Read Only) Descripti on Indicates whether Transmit (TX) Bandwidth Control Minimum capability is supported. Legal Values None Default Value Not Applicable Write Privilege Not Applicable License Required iDRAC Express or iDRAC Enterprise Depende ncy None NIC.VndrConfigGroup.TXFlowControl (Read Only) Descripti on Indicates whether Transmit (TX) Flow Control capability is supported.
NIC.VndrConfigGroup.VirtFIPMacAddr (Read or Write) Descripti on Programmatically assignable FIP-MAC address for FCoE. Programmatic write for support of I/O Identity feature. Legal Values String of up to 17 characters Default Value Not Applicable Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Depende ncy None NIC.VndrConfigGroup.VirtIscsiMacAddr (Read or Write) Descripti on Programmatically assignable MAC address for iSCSI offload.
NIC.VndrConfigGroup.VirtMacAddr (Read or Write) Descripti on Programmatically assignable MAC address. Programmatic write for support of I/O Identity feature. Legal Values String of up to 17 characters Default Value Not Applicable Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Depende ncy None NIC.VndrConfigGroup.VirtualLinkControl (Read or Write) Descripti on Indicates whether Virtual Link Control capability is supported.
NIC.VndrConfigGroup.VirtWWN (Read or Write) Descripti on Programmatically assignable Fibre Channel World Wide Node Name identifier for FCoE. Legal Values String of up to 23 characters Default Value Not Applicable Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Depende ncy None NIC.VndrConfigGroup.VirtWWPN (Read or Write) Descripti on Programmatically assignable Fibre Channel World Wide Port Name identifier for FCoE.
Default Value Not Applicable Write Privilege Not Applicable License Required iDRAC Express or iDRAC Enterprise Depende ncy None NIC.VndrConfigGroup.WWPN (Read Only) Descripti on Fibre Channel World Wide Port Name identifier for FCoE. Legal Values String of up to 23 characters Default Value Not Applicable Write Privilege Not Applicable License Required iDRAC Express or iDRAC Enterprise Depende ncy None Storage.Controller The objects in this group manage storage controller attributes.
Storage.Controller.BackgroundInitializationRate (Read or Write) Descripti on The Background Initialization (BGI) rate is the percentage of the system's resources dedicated to perform the background initialization of a virtual disk after it is created. Legal Values Values: 0–100 Default value 100 Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Depende ncy None Storage.Controller.
Storage.Controller.CheckConsistencyMode (Read or Write) Descripti on Check Consistency feature is used to verify the accuracy of the redundant (parity) information. Legal Values • • Default value Normal Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Depende ncy None Normal Stop On Error Storage.Controller.
Storage.Controller.ControllerBootMode (Read or Write) Descripti on This property indicates the Controller Boot Mode setting on the controller. Legal Values • • • • Default Value Not Applicable Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Depende ncy None User Mode Continue Boot On Error Headless Mode Continue On Error Headless Safe Mode Storage.Controller.
Storage.Controller.CurrentControllerMode (Read Only) Descripti Indicates the current personality mode of controllers. on Legal Values • • Default value RAID RAID Non-RAID License iDRAC Express or iDRAC Enterprise Required Depende None ncy Storage.Controller.EnhancedAutoImportForeignConfig (Read or Write) Descripti on This property indicates the Enhanced Auto Import of Foreign Configuration setting on the controller.
• Disabled Default value Automatic Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Depende ncy None Storage.Controller.PatrolReadRate (Read or Write) Descripti on The Patrol Read Rate is the percentage of the system's resources dedicated to perform Patrol Read. Legal Values Values: 0–100 Default value 30 Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Depende ncy None Storage.Controller.
Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Depende ncy None Storage.Controller.RebuildRate (Read or Write) Descripti on The Rebuild Rate is the percentage of the system's resources dedicated to rebuilding a failed disk when a rebuild is necessary. Legal Values Values: 0–100 Default value 100 Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Depende ncy None Storage.Controller.
Depende ncy None Storage.Controller.SupportControllerBootMode (Read Only) Descripti on This is read only attribute. This property indicates if this controller supports setting of controller boot mode. Legal Values • • Default Value Not Applicable Write Privilege Configure iDRAC License Required iDRAC Express or iDRAC Enterprise Depende ncy None Supported Not Supported Storage.Controller.SupportEnhancedAutoForeignImport (Read Only) Descripti on This is readonly attribute.
Storage.Controller.SupportRAID10UnevenSpans (Read Only) Descripti on This is readonly attribute. This property indicates if this controller supports uneven spans for RAID 10. Legal Values • • Supported Not Supported Default value Write Privilege Configure iDRAC License Required iDRAC Express or iDRAC Enterprise Depende ncy None Storage.Controller.T10PICapability (Read Only) Descripti on This is readonly attribute. This property indicates if this controller supports T10 PI.
Storage.enclosure.BackplaneCurrentMode (Read Only) Descripti on Displays the current mode of the backplane. Legal Values • • • Default Value UnifiedMode Write Privilege Not Applicable License Required iDRAC Express or iDRAC Enterprise Depende ncy Backplane must support. UnifiedMode SplitMode Not applicable Storage.enclosure.BackplaneRequestedMode (Read or Write) Descripti on Configures the backplane mode.
Storage.enclosure.BackplaneType (Read Only) Descripti on Indicates whether or not the backplane is shared. Legal Values • Shared • Not Shared Default Value Not Shared Write Privilege Not Applicable License Required iDRAC Express or iDRAC Enterprise Depende ncy Backplane must support. Storage.PhysicalDisk The objects in this group manage storage physical disk drive attributes. This group is indexed. The following section provides information about the objects in this group. Storage.
Storage.PhysicalDisk.MaxCapableSpeed (Read Only) Descripti on This is readonly attribute. The property represents the data transfer speed that the disk is capable of. Legal Values • • • • • Default value Not Applicable Write Privilege Not Applicable License Required iDRAC Express or iDRAC Enterprise Depende ncy None Unknown 1.5GBPS 3GBPS 6GBPS 12GBPS Storage.PhysicalDisk.
Storage.PhysicalDisk.T10PICapability (Read Only) Descripti on This is readonly attribute. This property indicates if this physical disk drive supports T10 PI. Legal Values • • Default value Not Applicable Write Privilege Not Applicable License Required iDRAC Express or iDRAC Enterprise Depende ncy None Incapable Capable Storage.VirtualDisk The objects in this group manage storage virtual disk attributes. This group is indexed.
Storage.VirtualDisk.DiskCachePolicy (Read or Write) Descripti on Set the physical disk drive caching policy of all members of a Virtual Disk by enabling the Disk Cache Policy. When this feature is enabled, the physical disk drive writes data to the physical disk drive cache before writing it to the physical disk drive. Because it is faster to write data to the cache than to a disk, enabling this feature can improve system performance.
Storage.VirtualDisk.T10PIStatus (Read or Write) Descripti on This property indicates if T10 PI is enabled or disabled on this virtual disk. NOTE: Can be disabled only if the current value for this object is enabled. Legal Values • • Default value 0 — Disabled Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Depende ncy None 0 — Disabled 1 — Enabled Storage.VirtualDisk.
A Deprecated and New Subcommands The following table provides the list of deprecated subcommands and equivalent new subcommands.
B Legacy and New Groups and Objects The following table provides the list of legacy groups and objects and equivalent groups and objects. Legacy Groups and Objects New Groups and Objects idRacInfo iDRAC.Info idRacType Type idRacProductInfo Product idRacDescriptionInfo Description idRacVersionInfo Version idRacBuildInfo Build idRacName Name cfgActiveDirectory iDRAC.
Legacy Groups and Objects New Groups and Objects cfgADDomainController3 DomainController3 cfgADGlobalCatalog1 GlobalCatalog1 cfgADGlobalCatalog2 GlobalCatalog2 cfgADGlobalCatalog3 GlobalCatalog3 cfgADCertValidationEnable CertValidationEnable cfgADSSOEnable SSOEnable cfgADDcSRVLookupEnable DCLookupEnable cfgADDcSRVLookupbyUserdoma DCLookupByUserDomain in cfgADDcSRVLookupDomainNam DCLookupDomainName e cfgADGcSRVLookupEnable GCLookupEnable cfgADGcRootDomain GCRootDomain cfgLanNetworking iD
Legacy Groups and Objects New Groups and Objects cfgNicVLanEnable VLanEnable cfgNicVLanID VLanID cfgNicVLanPriority VLanPriority iDRAC.IPv4 cfgNicIPv4Enable Enable cfgNicIpAddress Address cfgNicNetmask NetMask cfgNicGateway Gateway cfgNicUseDhcp DHCPEnable cfgDNSServersFromDHCP DNSFromDHCP cfgDNSServer1 DNS1 cfgDNSServer2 DNS2 cfgIpv6LanNetworking iDRAC.
Legacy Groups and Objects New Groups and Objects cfgIPv6Address4 Address4 cfgIPv6Address5 Address5 cfgIPv6Address6 Address6 cfgIPv6Address7 Address7 cfgIPv6Address8 Address8 cfgIPv6Address9 Address9 cfgIPv6Address10 Address10 cfgIPv6Address11 Address11 cfgIPv6Address12 Address12 cfgIPv6Address13 Address13 cfgIPv6Address14 Address14 cfgIPv6Address15 Address15 cfgIPv6DNSServersFromDHCP6 DNSFromDHCP6 cfgIPv6DNSServer1 DNS1 cfgIPv6DNSServer2 DNS2 cfgServerPower System.
Legacy Groups and Objects New Groups and Objects cfgServerPeakPowerConsumptio Max.Power n cfgServerPeakPowerConsumptio Max.Power.Timestamp nTimestamp cfgServerPowerConsumptionCle ar Max.PowerClear cfgServerPowerCapWatts Cap.Watts cfgServerPowerCapBtuhr Cap.BtuHr cfgServerPowerCapPercent Cap.Percent cfgServerPowerCapEnable Cap.Enable cfgServerPowerLastHourAvg Avg.LastHour cfgServerPowerLastDayAvg Avg.LastDay cfgServerPowerLastWeekAvg Avg.LastWeek cfgServerPowerLastHourMinPow Min.
Legacy Groups and Objects New Groups and Objects cfgServerPowerLastDayMaxTime Max.LastDay.Timestamp cfgServerPowerLastWeekMinPow Min.LastWeek er cfgServerPowerLastWeekMinTim e Min.LastWeek.Timestamp cfgServerPowerLastWeekMaxPo wer Max.LastWeek cfgServerPowerLastWeekMaxTim Max.LastWeek.Timestamp e cfgServerPowerInstHeadroom Realtime.Headroom cfgServerPowerPeakHeadroom Max.Headroom cfgServerActualAmperageConsu mption Realtime.Amps cfgServerPeakAmperage Max.
Legacy Groups and Objects New Groups and Objects cfgServerPowerSupplyMaxInputP MaxInputPower ower cfgServerPowerSupplyMaxOutpu MaxOutputPower tPower cfgServerPowerSupplyOnlineStat Status us cfgServerPowerSupplyFwVer FwVer cfgServerPowerSupplyCurrentDr aw CurrentDraw cfgServerPowerSupplyType Type cfgServerPowerBusMonitoring PMBusMonitoring cfgUserAdmin iDRAC.
Legacy Groups and Objects New Groups and Objects cfgRhostsSyslogServer2 Server2 cfgRhostsSyslogServer3 Server3 cfgRhostsSyslogPort Port iDRAC.Update cfgRhostsFwUpdateTftpEnable FwUpdateTFTPEnable cfgRhostsFwUpdateIpAddr FwUpdateIPAddr cfgRhostsFwUpdatePath FwUpdatePath [iDRAC.RemoteHosts] cfgRhostsSmtpServerIpAddr SMTPServerIPAddress cfgEmailAlert iDRAC.
Legacy Groups and Objects New Groups and Objects Port Timeout cfgSsnMgtRacadmTimeout iDRAC.Racadm Enable Timeout cfgSsnMgtConsRedirMaxSessions iDRAC.VirtualConsole EncryptEnable Enable PluginType LocalVideo Port MaxSessions Timeout AccessPrivilege cfgSsnMgtWebserverTimeout iDRAC.Webserver Enable HttpPort Timeout HttpsPort LowerEncryptionBitLength [cfgSerial] iDRAC.
Legacy Groups and Objects New Groups and Objects cfgSerialBaudRate BaudRate cfgSerialConsoleEnable Enable cfgSerialConsoleIdleTimeout IdleTimeout cfgSerialConsoleNoAuth NoAuth cfgSerialConsoleCommand Command cfgSerialHistorySize HistorySize iDRAC.SerialRedirection cfgSerialConsoleQuitKey QuitKey cfgSerialCom2RedirEnable Enable cfgSerialTelnetEnable iDRAC.Telnet cfgSerialSshEnable iDRAC.SSH [cfgOobSnmp] iDRAC.
Legacy Groups and Objects New Groups and Objects cfgRacTuneRemoteRacadmEnabl iDRAC.Racadm e=1 cfgRacTuneWebserverEnable=1 iDRAC.Webserver cfgRacTuneHttpPort=80 iDRAC.Webserver cfgRacTuneHttpsPort=443 iDRAC.Webserver cfgRacTuneTelnetPort=23 iDRAC.Telnet cfgRacTuneSshPort=22 iDRAC.SSH cfgRacTuneConRedirEnable=1 iDRAC.VirtualConsole cfgRacTuneConRedirPort=5900 iDRAC.VirtualConsole cfgRacTuneConRedirEncryptEna ble=1 iDRAC.VirtualConsole cfgRacTuneLocalServerVideo=1 iDRAC.VirtualConsole iDRAC.
Legacy Groups and Objects New Groups and Objects iDRAC.Time cfgRacTuneTimezoneOffset=0 TimeZoneOffset cfgRacTuneDaylightOffset=0 DaylightOffset cfgRacTuneAsrEnable=1 TBD cfgRacTunePlugintype=0 iDRAC.VirtualConsole iDRAC.LocalSecurity cfgRacTuneCtrlEConfigDisable= 0 PrebootConfig cfgRacTuneLocalConfigDisable= 0 LocalConfig cfgRacTuneVirtualConsoleAuthor iDRAC.VirtualConsole izeMultipleSessions=0 ifcRacManagedNodeOs System.
Legacy Groups and Objects New Groups and Objects cfgRacSecCsrCountryCode CsrCountryCode cfgRacSecCsrEmailAddr CsrEmailAddr cfgRacVirtual iDRAC.VirtualMedia cfgVirMediaAttached Attached cfgVirtualBootOnce BootOnce cfgVirMediaFloppyEmulation FloppyEmulation cfgLDAP iDRAC.
Legacy Groups and Objects New Groups and Objects cfgLdapRoleGroupPrivilege Privilege cfgStandardSchema iDRAC.ADGroup cfgSSADRoleGroupIndex NA cfgSSADRoleGroupName Name cfgSSADRoleGroupDomain Domain cfgSSADRoleGroupPrivilege Privilege cfgIpmiSerial iDRAC.
Legacy Groups and Objects New Groups and Objects cfgIpmiSolMinPrivilege MinPrivilege cfgIpmiSolAccumulateInterval AccumulateInterval cfgIpmiSolSendThreshold SendThreshold cfgIpmiLan iDRAC.IPMILan cfgIpmiLanEnable Enable cfgIpmiLanPrivilegeLimit PrivLimit cfgIpmiLanAlertEnable AlertEnable cfgIpmiEncryptionKey EncryptionKey cfgIpmiPetCommunityName CommunityName cfgUserDomain iDRAC.UserDomain cfgUserDomainIndex NA cfgUserDomainName Name cfgSmartCard iDRAC.
Legacy Groups and Objects New Groups and Objects cfgVFlashSDAvailableSize AvailableSize cfgVFlashSDHealth Health cfgVFlashSDEnable Enable cfgVFlashSDWriteProtect WriteProtect cfgVFlashSDInitialized Initialized cfgVFlashPartition iDRAC.
Legacy Groups and Objects New Groups and Objects cfgIpmiPetAlertDestIpAddr DestAddr cfgSSADRoleGroupPrivilege (Read or Write) Descripti on Use the bit mask numbers listed in the table below to set rolebased authority privileges for a Role Group.
Access Virtual Console 0x00000020 Access Virtual Media 0x00000040 Test Alerts 0x00000080 Execute Debug Commands 0x00000100 672
