CLI Guide

ManualsBrandsDell ManualsActive System ManageriDRAC8 with Lifecycle Controller version 2.81.81.81

Table Of Contents

iDRAC 8/7 v2.81.81.81 RACADM CLI Guide

2021

Rev. A00

Summary of content (553 pages)

PAGE 1
iDRAC 8/7 v2.81.81.81 RACADM CLI Guide 2021 Rev.
PAGE 2
Notes, cautions, and warnings NOTE: A NOTE indicates important information that helps you make better use of your product. CAUTION: A CAUTION indicates either potential damage to hardware or loss of data and tells you how to avoid the problem. WARNING: A WARNING indicates a potential for property damage, personal injury, or death. © 2021 July Dell Inc. or its subsidiaries. All rights reserved. Dell, EMC, and other trademarks are trademarks of Dell Inc. or its subsidiaries.
PAGE 3
Contents Chapter 1: Introduction............................................................................................................... 33 New in this release............................................................................................................................................................33 Supported RACADM Interfaces.....................................................................................................................................33 RACADM Syntax Usage.....
PAGE 4
getsensorinfo......................................................................................................................................................................73 getssninfo............................................................................................................................................................................ 77 getsvctag.......................................................................................................................................
PAGE 5
vflashsd.............................................................................................................................................................................. 156 vflashpartition...................................................................................................................................................................156 vmdisconnect...................................................................................................................................
PAGE 6
cfgSessionManagement................................................................................................................................................. 172 cfgSsnMgtRacadmTimeout (Read or Write)...................................................................................................... 172 cfgSsnMgtConsRedirMaxSessions (Read or Write)......................................................................................... 173 cfgSsnMgtWebserverTimeout (Read or Write).................
PAGE 7
cfgServerInfo....................................................................................................................................................................186 cfgServerName (Read Or Write)...........................................................................................................................186 cfgServerNic3MacAddress (Read Only)..............................................................................................................
PAGE 8
cfgThermalEnhancedCoolingMode (Read or Write)......................................................................................... 199 cfgIpmiSol..........................................................................................................................................................................199 cfgIpmiSolEnable (Read or Write).........................................................................................................................
PAGE 9
cfgServerPowerLastDayMinTime (Read Only)..................................................................................................209 cfgServerPowerLastDayMaxPower (Read Only)..............................................................................................209 cfgServerPowerLastDayMaxTime (Read Only)................................................................................................. 210 cfgServerPowerLastWeekMinPower (Read Only)...............................................
PAGE 10
cfgIPv6StaticGateway (Read or Write)............................................................................................................... 221 cfgIPv6StaticPrefixLength (Read or Write)....................................................................................................... 221 cfgIPv6StaticAutoConfig (Read/Write).............................................................................................................. 221 cfgIPv6StaticDNSServersFromDHCP6 (Read or Write)............
PAGE 11
cfgLoggingSELOEMEventFilterEnable (Read or Write)..................................................................................232 cfgRacSecurity................................................................................................................................................................ 232 cfgRacSecCsrCommonName (Read or Write).................................................................................................. 233 cfgRacSecCsrOrganizationName (Read or Write).............
PAGE 12
System.Location.Chassis.Name (Read Only)..................................................................................................... 249 System.Location.Chassis.Slot (Read or Write)..................................................................................................249 System.OpenIDConnectServer....................................................................................................................................249 System.OpenIDConnectServer.DiscoveryURL (Read or Write)...
PAGE 13
System.Power.Supply.................................................................................................................................................... 264 System.Power.Supply.CurrentDraw (Read Only)............................................................................................. 264 System.Power.Supply.FwVer (Read Only)......................................................................................................... 264 System.Power.Supply.[i].MaxInputPower (Read Only)...
PAGE 14
LifecycleController.LCAttributes.UserProxyType (Read and Write)............................................................278 LifecycleController.LCAttributes.UserProxyUserName (Read or Write).................................................... 278 LifecycleController.LCAttributes.VirtualAddressManagementApplication (Read or Write)................... 278 iDRAC.ActiveDirectory.....................................................................................................................................
PAGE 15
iDRAC.IOIDOpt.VirtualAddressPersistencePolicyNonAuxPwrd (Read or Write)...................................... 292 iDRAC.IPBlocking............................................................................................................................................................ 292 iDRAC.IPBlocking.BlockEnable (Read or Write)................................................................................................ 292 iDRAC.IPBlocking.FailCount (Read or Write)..................................
PAGE 16
iDRAC.IPv6.Address2 (Read or Write)................................................................................................................ 306 iDRAC.IPv6.Address3 (Read or Write)................................................................................................................ 306 iDRAC.IPv6.Address4 (Read or Write)................................................................................................................ 307 iDRAC.IPv6.Address5 (Read or Write).....................
PAGE 17
iDRAC.Logging.SELOEMEventFilterEnable (Read or Write)......................................................................... 320 iDRAC.NIC........................................................................................................................................................................ 320 iDRAC.NIC.Autoconfig (Read or Write).............................................................................................................. 320 iDRAC.NIC.AutoDetect (Read or Write)............
PAGE 18
iDRAC.RemoteHosts.SMTPServerIPAddress (Read or Write)......................................................................335 iDRAC.RFS........................................................................................................................................................................335 iDRAC.RFS.IgnoreCertWarning (Read or Write)...............................................................................................335 iDRAC.RFS.MediaAttachState (Read Only)........................
PAGE 19
iDRAC.ServiceModule.WMIInfo (Read or Write).............................................................................................. 348 iDRAC.SmartCard........................................................................................................................................................... 348 iDRAC.SmartCard.SmartCardCRLEnable (Read or Write)............................................................................. 348 iDRAC.SmartCard.SmartCardLogonEnable (Read or Write)...........
PAGE 20
iDRAC.USB.PortStatus (Read or Write).............................................................................................................. 361 iDRAC.Telnet.Timeout (Read or Write)................................................................................................................361 iDRAC.UserDomain......................................................................................................................................................... 362 iDRAC.UserDomain.
PAGE 21
iDRAC.VirtualMedia.KeyEnable (Read or Write)............................................................................................... 375 iDRAC.VNCServer...........................................................................................................................................................375 iDRAC.VNCServer.Enable (Read or Write).........................................................................................................375 iDRAC.VNCServer.
PAGE 22
BIOS.IntegratedDevices.IntegratedSas (Read or Write).................................................................................389 BIOS.IntegratedDevices.InternalSdCard (Read or Write)...............................................................................390 BIOS.IntegratedDevices.InternalSdCardRedundancy (Read or Write)........................................................390 BIOS.IntegratedDevices.InternalUsb (Read or Write)..................................................................
PAGE 23
BIOS.OneTimeBoot.OneTimeHddSeqDev (Read or Write)............................................................................ 404 BIOS.OneTimeBoot.OneTimeUefiBootSeqDev (Read or Write)................................................................... 405 BIOS.ProcSettings..........................................................................................................................................................405 BIOS.ProcSettings.CorePerfBoost (Read or Write)..................................
PAGE 24
BIOS.ProcSettings.ProcSoftwarePrefetcher (Read or Write)...................................................................... 420 BIOS.ProcSettings.ProcVirtualization (Read or Write)................................................................................... 420 BIOS.ProcSettings.ProcX2Apic (Read or Write)............................................................................................... 421 BIOS.ProcSettings.QpiBandwidthPriority (Read or Write)...........................................
PAGE 25
BIOS.SataSettings.SataPortHCapacity (Read or Write).................................................................................434 BIOS.SataSettings.SataPortHDriveType (Read or Write).............................................................................. 435 BIOS.SataSettings.SataPortHModel (Read Only)............................................................................................ 435 BIOS.SataSettings.SataPortI (Read or Write).........................................................
PAGE 26
BIOS.SysProfileSettings.PowerDelivery (Read or Write)............................................................................... 450 BIOS.SysProfileSettings.Proc1TurboCoreNum (Read or Write)................................................................... 450 BIOS.SysProfileSettings.Proc2TurboCoreNum (Read or Write)................................................................... 451 BIOS.SysProfileSettings.ProcC1E (Read or Write)......................................................................
PAGE 27
FC.FCDevice.EFIVersion (Read Only)..................................................................................................................466 FC.FCDevice.FamilyVersion (Read Only)............................................................................................................466 FC.FCDevice.PCIDeviceID (Read Only).............................................................................................................. 466 FC.FCTarget..................................................
PAGE 28
NIC.DCBSettings.CongestionNotification (Read Only)................................................................................... 479 NIC.DCBSettings.DCBExchangeProtocol (Read Only)....................................................................................479 NIC.DCBSettings.EnhancedTransmissionSelection (Read Only).................................................................. 480 NIC.DCBSettings.PriorityFlowControl (Read Only)................................................................
PAGE 29
NIC.IscsiFirstTgtParams.FirstTgtBootLun (Read or Write)........................................................................... 493 NIC.IscsiFirstTgtParams.FirstTgtChapId (Read or Write).............................................................................. 494 NIC.IscsiFirstTgtParams.FirstTgtChapPwd (Password)................................................................................. 494 NIC.IscsiFirstTgtParams.FirstTgtIpAddress (Read or Write)...............................................
PAGE 30
NIC.NICConfig.BootStrapType (Read or Write)............................................................................................... 508 NIC.NICConfig.HideSetupPrompt (Read or Write).......................................................................................... 508 NIC.NICConfig.LegacyBootProto (Read or Write)...........................................................................................509 NIC.NICConfig.LnkSpeed (Read or Write)...................................................
PAGE 31
NIC.VndrConfigGroup.VirtualLinkControl (Read or Write).............................................................................523 NIC.VndrConfigGroup.VirtWWN (Read or Write).............................................................................................523 NIC.VndrConfigGroup.VirtWWPN (Read or Write)..........................................................................................523 NIC.VndrConfigGroup.WWN (Read Only)................................................................
PAGE 32
Storage.enclosure........................................................................................................................................................... 536 Storage.enclosure.BackplaneCurrentMode (Read Only)................................................................................ 536 Storage.enclosure.BackplaneRequestedMode (Read or Write)....................................................................536 Storage.enclosure.BackplaneType (Read Only).............................
PAGE 33
1 Introduction This document provides information about the RACADM subcommands, supported RACADM interfaces, and property database groups and object definitions for the following: ● iDRAC for Blade Servers ● iDRAC on Rack and Tower Servers Most of the commands mentioned in this document are applicable for multi-generation servers. That is, the commands are applicable for iDRAC6, iDRAC7, and iDRAC8.
PAGE 34
● Remote — Supports running RACADM commands from a remote management station such as a laptop or desktop. To run Remote RACADM commands, install the DRAC Tools utility from the OpenManage software on the remote computer. To run Remote RACADM commands: ○ Formulate the command as a SSH or Telnet RACADM command. For more information about the options, see RACADM Subcommand Details. To download the local RACADM tool from www.dell.
PAGE 35
● To display the supported indexes for a specified group, run: racadm get device. Example racadm get nic.nicconfig NIC.nicconfig.1 [Key=NIC.Integrated.1-1-1#nicconfig] NIC.nicconfig.2 [Key=NIC.Integrated.1-2-1#nicconfig] NIC.nicconfig.3 [Key=NIC.Integrated.1-3-1#nicconfig] NIC.nicconfig.4 [Key=NIC.Integrated.1-4-1#nicconfig] ● To display the object list for the specified group, run: racadm get device.. Example racadm get nic.nicconfig.2 [Key=NIC.Integrated.
PAGE 36
Table 1. RACADM Command Options (continued) Option Description NOTE: CMC does not support extended ASCII characters, such as ß, å, é, ü, or other characters used primarily in nonEnglish languages. Setting values with these characters causes unpredictable behavior. --nocertwarn Does not display certificate-related warning message. -i Specifies the index number for the indexed group, if applicable. -g Specifies the group name if applicable.
PAGE 37
gettracelog getversion ● Example 3: racadm> getl racadm> getled or LEDState: Not-Blinking ● Example 4: racadm>> get bios.uefiBootSettings BIOS.UefiBootSettings BIOS.UefiBootSettings.UefiBootSeq BIOS.UefiBootSettings.UefiPxeIpVersion NOTE: In the RACADM autocomplete mode, some of the RACADM commands specific to certain server platforms may not be available. In such scenarios, execute the RACADM command in the normal execution mode.
PAGE 38
Supported RACADM Subcommands The following table provides the list of RACADM subcommands and their corresponding interface support. For more information about the RACADM subcommands including syntax and valid entries, see RACADM Subcommand Details on page 42. Table 2.
PAGE 39
Table 2.
PAGE 40
Table 2. Supported RACADM Subcommands (continued) Subcommand iDRAC on Blade Servers Telnet/SSH/ Serial Local RACADM Remote RACADM usercertupload on page 154 No Yes Yes usercertview on page 155 Yes Yes Yes vflashsd on page 156 Yes Yes Yes vflashpartition on page 156 Yes Yes Yes vmdisconnect on page 157 Yes Yes Yes Other Documents You May Need In addition to this guide, you can access the following guides available on the Dell Support website at https://www.dell.com/ esmmanuals.
PAGE 41
● Dell EMC support site: 1. Go to https://www.dell.com/support. 2. Click Browse all products. 3. From the All products page, click Software, and then click the required link. 4. Click the required product and then click the required version. Using search engines, type the name and version of the document in the search box. Contacting Dell NOTE: If you do not have an active Internet connection, you can find contact information on your purchase invoice, packing slip, bill, or Dell product catalog.
PAGE 42
2 RACADM Subcommand Details This section provides detailed description of the RACADM subcommands including the syntax and valid entries. Topics: • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • 42 Guidelines to Quote Strings Containing Special Characters When Using RACADM Commands Help and help subcommand arp autoupdatescheduler cd cd..
PAGE 43
• • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • racreset racresetcfg remoteimage rollback sensorsettings serveraction set setled setniccfg sshpkauth sslcertdownload sslcertupload sslcertview sslcertdelete sslcsrgen sslkeyupload sslresetcfg storage swinventory systemconfig systemerase systemperfstatistics techsupreport testemail testtrap testalert traceroute traceroute6 update usercertupload usercertview vflashsd vflashpartition vmdisconnect Guidelines to Quote Strings Containing Specia
PAGE 44
NOTE: The - (dash) character cannot be the first character of the string, regardless of whether the string is quoted. There are different escaping rules for double quotation marks. There are different escaping rules for using single quotation mark and double quotation marks. For using double quotation marks: The following characters must be escaped by prepending a backward slash: ● ● ● ● ● $ (dollar sign) " (double quotation mark) ' (single quotation marks) ` (back quotation mark) \ (backward slash) For e
PAGE 45
arp Table 4. arp table Description Displays the contents of the Address Resolution Protocol (ARP) table. ARP table entries cannot be added or deleted. To use this subcommand, you must have Debug privilege. To use this subcommand, you must have Execute Diagnostic Commands. Synopsis Input Example racadm arp N/A racadm arp Table 5. Output Address HW Type HW Address Mask 192.168.1.1 Ether 00:0d:65:f3:7c:bf C Device eth0 autoupdatescheduler Table 6.
PAGE 46
Table 6. Details of autoupdatescheduler (continued) Input Valid options: ● -u — Specifies the user name of the remote share that stores the catalog file. NOTE: For CIFS, enter the domain name as domain or username. ● -p — Specifies the password of the remote share that stores the catalog file. ● -l — Specifies the network share (NFS, CIFS, FTP, TFTP, HTTP, or HTTPS) location of the catalog file. IPv4 and IPv6 addresses are supported. ● -f — Specifies the catalog location and the filename.
PAGE 47
Table 6. Details of autoupdatescheduler (continued) ○ For HTTP, run the command: racadm autoupdatescheduler create -u httpuser -p httppwd -l http:// test.com -f cat.xml -ph 10.20.30.40 -pu padmin -pp ppwd -po 8080 -pt http -time 14:30 -dom 1 -rp 5 -a 1 ○ For HTTPS, run the command: racadm autoupdatescheduler create -u httpuser -p httppwd -l https:// test.com -f cat.xml -ph 10.20.30.
PAGE 48
cd.. Table 8. Details of cd.. Description Synopsis Input To go back to the previous directory, use this command. racadm> cd.. racadm> cd.. Output To traverse back to the previous directory, use the command. Example ● Example 1: To traverse back from power to system object: ○ Input: racadm/power> cd.. ○ Output: system>> ● Example 2: To traverse back from system object to the prompt: ○ Input: racadm/system> cd.. ○ Output: racadm>> clearasrscreen Table 9.
PAGE 49
Table 10. Details of clearpending (continued) ● ● ● ● BIOS FQDD NIC FQDD FC FQDD Storage controller FQDD : The values are: ● BIOS.Setup.1–1 ● NIC.Integrated.1–1 ● RAID.Integrated.1–1 Output A message is displayed indicating that the pending state is cleared or deleted. Example racadm clearpending NIC.Integrated.1-1 closessn Table 11. Details of closessn attribute Description Closes a communication session on the device.
PAGE 50
clrsel Table 12. Details of clrsel attribute Description Removes all the existing records from the System Event Log (SEL). To use this subcommand, you must have Clear Logs permission. Synopsis Input racadm clrsel [-m ] -m must be one of the following values: ● server- — where n=1 to 16 ● server- — where n=1 to 8; x = a, b, c, d (lower case) Example ● racadm clrsel The SEL was cleared successfully ● racadm clrsel -m server-1 Clear SEL log on server 1 config Table 13.
PAGE 51
Table 13. Details of config attribute (continued) ● -continue — This option is used with -f option only. If configuration through file is unsuccessful for a group, then configuration continues with the next group in the file. If this option is not used, then configuration stops when it is unsuccessful for a particular group. After the unsuccessful group, the rest of the groups are not configured. ● -p — This option must be used with the -f option.
PAGE 52
Table 14. Details of coredump (continued) Example ● racadm coredump There is no coredump currently available. ● racadm Feb 19 Feb 19 Feb 19 Feb 19 Feb 22 coredump 15:51:40 15:52:41 15:54:12 15:56:11 11:46:11 (none) (none) (none) (none) (none) last message last message last message last message kernel: repeated repeated repeated repeated 5 4 4 2 times times times times coredumpdelete Table 15. Details of coredumpdelete Description Deletes any currently available coredump data stored in the RAC.
PAGE 53
Table 16. Details of diagnostics (continued) ● ● ● ● ● ● ● ○ 0(Express) — The express mode executes a subset of diagnostic tests. ○ 1(Extended) — The extended mode executes all available diagnostics tests. ○ 2(Both) — Runs express and extended tests serially in sequence. -f — Specifies the name of the configuration file. -l — Specifies the location of the network share (NFS or CIFS). -u — Specifies the user name of the remote share to import the file.
PAGE 54
Table 17. Details of eventfilters (continued) where, category is mandatory, but subcategory and severity are optional. A severity cannot precede a subcategory. Valid Category values are: ● ● ● ● ● ● ● All System Storage Updates Audit Config Worknotes Valid Severity values are: ● Critical ● Warning ● Info Valid examples of alert queries are: ● ● ● ● ● idrac.alert.all idrac.alert.audit idrac.alert.audit.lic idrac.alert.audit.warning idrac.alert.audit.lic.
PAGE 55
Table 17. Details of eventfilters (continued) ● Display eventfilter configurations for a specific severity and subcategory. For example, a severity of warning in the subcategory licensing under audit category: racadm eventfilters get -c idrac.alert.audit.lic.warning ● Clear all available alert settings: racadm eventfilters set -c idrac.alert.all -a none -n none ● Configure using severity as a parameter.
PAGE 56
Table 19. Details of frontpanelerror (continued) Synopsis racadm frontpanelerror show racadm frontpanelerror hide Input ● show — to view the errors currently being displayed on the LCD screen. ● hide — to hide the errors currently being displayed on the LCD screen. Example ● racadm frontpanelerror show Front Panel Error—Show Enabled. ● racadm frontpanelerror hide Front Panel Error—Hide Enabled. fwupdate Table 20.
PAGE 57
Table 20. Details of fwupdate (continued) ● For Dell’s 13th generation of PowerEdge servers and later, CMC firmware includes a signature which is verified by CMC before update to ensure the authenticity of the uploaded firmware. The firmware update process is successful only if the firmware image is authenticated by CMC to be a valid image from the service provider and has not been altered. The firmware update process is stopped if CMC cannot verify the signature of the uploaded firmware image.
PAGE 58
Table 20. Details of fwupdate (continued) NOTE: When attempting to run firmware update task using racadm fwupdate command, if the firmware image path length is greater than 256 characters. Remote RACADM client exits with the error message "ERROR: Specified path is too long". Input ● —u — The update option performs a checksum of the firmware update file and starts the actual update process. This option may be used along with the —g or —p options. At the end of the update, iDRAC performs a soft reset.
PAGE 59
Table 20. Details of fwupdate (continued) ● -f — Specifies the FTP server IP address or FQDN, username, and password used for firmware image. Applies FTP download process for firmware update. ● -c — Cancels an ongoing firmware update. The cancel operation is supports the following values: ○ cmc-active — This is the default option if -m is not specified.
PAGE 60
Table 20. Details of fwupdate (continued) racadm fwupdate -g -u -a 192.168.0.2 -d After the image file is downloaded from the TFTP server, the update process begins. When completed, CMC is reset. ● Read the status of the firmware update. racadm fwupdate -s ● Cancel a firmware update in progress.
PAGE 61
Table 21. Firmware update methods on Blade, Rack and Tower servers (continued) FW Update Method iDRAC on Blade Servers iDRAC on Rack and Tower Servers Firmware RACADM-FTP Yes Yes Table 22. Firmware update methods on CMC servers FW Update Method CMC Local RACADM No Local RACADM-TFTP No Local RACADM-FTP No Remote RACADM Yes Remote RACADM-TFTP Yes Remote RACADM-FTP Yes Firmware RACADM-TFTP Yes Firmware RACADM-FTP Yes get Table 23.
PAGE 62
Table 23. Details of get (continued) Multi-object Get racadm get -f racadm get -f -t xml -l [--clone | --replace ] [--includeph] racadm get -f -t xml -l -c [,*] racadm get -f -t xml -u -p -l [--clone | --replace ] [--includeph] racadm get -f -t xml -u -p -l -c [,*] Input ● ○ Examples for FQDDs ￭ System.Power ￭ System.Power.
PAGE 63
Table 23. Details of get (continued) Examples ● Get system LCD information. racadm get system.lcdLCDUserString ● Display an entire group, in this case the topology configuration. racadm get system.location ● Display a single object from a particular group. racadm get system.location.rack.name ● Export the xml configuration to a CIFS share. racadm get -f file -t xml -u myuser -p xxx -l //192.168.0/share ● Export the xml configuration to an NFS share. racadm get -f file -t xml -l 192.168.
PAGE 64
Table 24. Details of getconfig attribute (continued) Synopsis racadm getconfig -f racadm getconfig -g [-i ] racadm getconfig -u racadm getconfig -h racadm getconfig -g -o [-i index] Input ● -f — The -f option directs getconfig to write the entire iDRAC configurations to a configuration file. This file can be used for batch configuration operations using the config subcommand.
PAGE 65
Table 24. Details of getconfig attribute (continued) ● iDRAC to myrac.cfg. racadm getconfig -f myrac.cfg If you do not configure the following key attributes in their respective groups for a particular index, the groups are not saved in to the file. This is applicable for all the index groups. Saves all group configuration objects from iDRAC to myrac.cfg. racadm getconfig -f myrac.cfg Saves all group configuration objects from iDRAC to myrac.cfg. racadm getconfig -f myrac.cfg Table 25.
PAGE 66
Table 24. Details of getconfig attribute (continued) ● Displays the current Enhanced Cooling Mode property configuration. racadm getconfig –g cfgThermal gethostnetworkinterfaces Table 26. Details of gethostnetworkinterfaces Description Synopsis Displays host network interface details. NOTE: To run this subcommand, you must have iDRAC service module installed on the server operating system.
PAGE 67
getled Table 27. Details of getled attribute Description Displays the LED settings on a module: blinking, not blinking, or unknown (for empty slots). To run this subcommand, you must have the Login User privilege.
PAGE 68
Table 28. Details of getniccfg attribute (continued) ● ● ● ● Output chassis : Default state if -m is not specified. server- : where n=1–16 server- : where n=1–8; x = a, b, c, d (lower case) switch- : where n=1–6 NOTE: Table 29. Output IPv4 settings: NIC Enabled =1 IPv4 Enabled =1 DHCP Enabled =1 IP Address =10.94.225.165 Subnet Mask =255.255.255.128 Gateway =10.94.225.
PAGE 69
Table 28. Details of getniccfg attribute (continued) Table 29. Output (continued) Speed =1Gb/s Duplex Mode =Full Duplex Active NIC =Dedicated Static IPv4 settings: Static IP Address =192.168.0.120 Static Subnet Mask =255.255.255.0 Static Gateway =192.168.0.1 Static IPv6 settings: Static IP Address 1 =2000:de11:bcd1:fc14:1234:5678:2468:abcd/ 64 Static Prefix Length =64 Static Gateway =:: IPv6 information is displayed only if IPv6 is enabled in iDRAC.
PAGE 70
Table 30. Details of getraclog attribute (continued) ● -c — Specifies the number of records to display. NOTE: On Remote RACADM, the number of logs are restricted to 25 by default. ● -i — Displays the number of entries in the CMC log. ● --more — Displays one screen at a time and prompts you to continue (similar to the UNIX more command). ● -s — Specifies the starting record used for the display. NOTE: When Enhanced Chassis Logging and Events feature is enabled, then -i and --more options are not displayed.
PAGE 71
Table 30. Details of getraclog attribute (continued) Timestamp Message Arg Message Arg Message sid=4818 Example = 2014-10-18 15:48:10 1 = 14503 2 = 48186 = Successfully closed Session process: pid=14503 Display the recent 2 records for RAC log racadm getraclog -c 2 SeqNumber = 4102 Message ID = LIC201 Category = Audit AgentID = DE Severity = Warning Timestamp = 2014-06-12 01:38:19 Message = License yPMRJGuEf7z5HG8LO7gh assigned to device iDRAC expires in 4 days.
PAGE 72
getremoteservicesstatus Table 32. Details of getremoteservicesstatus Description Displays the status of a system.
PAGE 73
Table 33. Details of getsel attribute (continued) Example ● Display entire log. racadm getsel ● Display number of records in log. racadm getsel -i getsensorinfo Table 34. Details of getsensorinfo Description Displays the status for system sensors. NOTE: For Dell PowerEdge FX2 chassis with FM120x4 server, the power related information is not displayed. NOTE: General purpose graphical processing unit (GPGPU) status is displayed only on PowerEdge C4130 servers.
PAGE 74
Table 38. Temperature sensor (continued) System Board Fan1 RPM Ok 5880 RPM 600 RPM NA 21% System Board Fan2 RPM Ok 6000 RPM 600 RPM NA 0% System Board Fan3 RPM Ok 5880 RPM 600 RPM NA 0% System Board Fan4 RPM Ok 5880 RPM 600 RPM NA 0% System Board Fan5 RPM Ok 5640 RPM 600 RPM NA 144% System Board Fan6 RPM Ok 5880 RPM 600 RPM NA 152% Table 39. Voltage sensor CPU1 VCORE PG Ok Good NA NA System Board 3.
PAGE 75
Table 39. Voltage sensor (continued) System Board DIMM Ok PG Good NA NA Table 40. Current sensor [R/W] [R/W] PS1 Current 1 Ok 0.4 Amps NA NA 0 Amps [N] 0 Amps [N] System Board Pwr Consumption Ok 56 Watts NA 1386 Watts 0 Watts [N] 1260 Watts [N] Table 41. PROCESSOR sensor CPU1 Status Ok Presence Detected NA NA CPU2 Status N/A Absent NA NA Table 42.
PAGE 76
Table 42. MEMORY sensor (continued) DIMM B12 N/A Absent NA NA Table 43.
PAGE 77
Table 48. SYSTEM PERFORMANCE sensor (continued) System Board IO Usage NonCritical 0% 0% 100% 0% [N] 99% [Y] System Board MEM Usage NonCritical 0% 0% 100% 0% [N] 99% [Y] System Board SYS Usage NonCritical 0% 0% 100% 0% [N] 99% [Y] getssninfo Table 49. Details of getssninfo attribute Description Displays a list of users that are connected to iDRACCMC.
PAGE 78
Table 51. Details of attribute (continued) Synopsis racadm getsvctag [-m ] Input -m ● ● ● ● — Must be one of the following values: chassis server- — where n = 1–16 server- — where n = 1–8; x = a, b, c, d (lower case) switch- — where n = 1–6 Output Any system tag as applicable. Example ● Display Service tag of Server in Slot 1 racadm getsvctag -m server-1 ● Display Service tag of all the components in the chassis racadm getsvctag getsysinfo Table 52.
PAGE 79
VLAN Priority VLAN Enabled = 0 = 0 CMC IPv4 Information: IPv4 Enabled Current IP Address Current IP Gateway Current IP Netmask DHCP Enabled Current DNS Server 1 Current DNS Server 2 DNS Servers from DHCP = = = = = = = = 1 192.168.0.10 192.168.0.10 255.255.255.0 1 0.0.0.0 0.0.0.
PAGE 80
Current IP Address 5 Current IP Address 6 Current IP Address 7 Current IP Address 8 Current IP Address 9 Current IP Address 10 Current IP Address 11 Current IP Address 12 Current IP Address 13 Current IP Address 14 Current IP Address 15 DNS Servers from DHCPv6 Current DNS Server 1 Current DNS Server 2 = = = = = = = = = = = = = = :: :: :: :: :: :: :: :: :: :: :: Disabled 2011:de11:bdc:192::67/64 :: System Information: System Model System Revision System BIOS Version Service Tag Express Svc Code Host Name
PAGE 81
Table 53. Details of attribute (continued) Displays the CMC diagnostic trace log. Synopsis ● racadm gettracelog [-i] ● racadm gettracelog [-s ] [-c ] [--more] Input ● —i — Displays the number of entries in iDRACCMC trace log. ● --more — Displays one screen at a time and prompts the user to continue (similar to the UNIX more command). ● -c — Specifies the number of records to display. ● -s — Specifies the starting record to display.
PAGE 82
Table 55. Details server-1 1.40.40 (Build 08) PowerEdge M520 iDRAC Y server-2 3.50 (Build 2) PowerEdgeM610x iDRAC6 Y server-4 3.50 (Build 4) PowerEdgeM710HD iDRAC6 Table 56. Details < Server > < CPLD Version > < Blade Type > server-1 1.0.5 PowerEdgeM520 server-2 1.0.3 PowerEdgeM610x server-4 1.0.0 PowerEdgeM710HD server-5 1.0.3 PowerEdgeM710 server-7 1.0.6 PowerEdgeM620 server-9 1.0.
PAGE 83
Table 57. Details (continued) server-5 6.3.0 PowerEdgeM710 server-7 1.7.1 PowerEdgeM620 server-9 1.7.1 PowerEdgeM520 Table 58. Details < Switch > < Model Name > < HW Version > < FW Version > switch-1 MXL 10/40GbE X01 9-2(0-296) switch-2 M8024-k 10GbE SW A00 switch-3 Dell PowerConnect M8024 X00 switch-4 Dell PowerConnect M8024 X00 switch-5 Dell PowerConnect M6348 X02 switch-6 Dell PowerConnect M6220 A01 5.0.1.3 hwinventory Table 59.
PAGE 84
Examples ● To get the list of NIC FQDDs, type the following command: racadm hwinventory nic NIC.Slot.2-1-1:Emulex OCe14102-U1-D - 00:90:FA:4C:FE:C2 PartitionCapable : 1 NIC.Slot.2-1-2:Emulex OCe14102-U1-D - 00:90:FA:4C:FE:C3 PartitionCapable : 2 NIC.Slot.2-1-3:Emulex OCe14102-U1-D - 00:90:FA:4C:FE:C4 PartitionCapable : 3 NIC.Slot.
PAGE 85
Max Bandwidth: Min Bandwidth: FCoE WWNN: Vendor Name: Number of PCI-e Functions Supported per Port: Number of PCI-e Functions Currently Enabled per Port: Family Driver Version: Protocol: Link Duplex: Link Speed: Auto Negotiated: Transmit Flow Control: Receive Flow Control: Media Type: NIC Mode: FCoE Offload Mode: iSCSI Offload Mode: Max Number of IOs per session supported: Number of Max LOGINs per port: Max Number of exchanges: Max NPIV WWN per port: Number of Targets Supported: Max Number of outstanding co
PAGE 86
● To export the inventory to a remote NFS share, type the following command: racadm hwinventory export -f Myinventory.xml -u admin -p xxx -l 1.2.3.4:/share ● To export the inventory to local file system using local Racadm, type the following command: racadm hwinventory export -f Myinventory.xml ● To display the Standard hardware inventory verbose description for the FC.Slot.2–1, type the following command: racadm hwinventory FC.Slot.
PAGE 87
Second FC Target WWPN: Second FC Target LUN: Hard Zone Address: Hard Zone Enable: FC Tape Enable: Loop reset Delay: Frame Payload Size : Fabric Login Retry Count: Fabric Login Timeout: Port Login Retry Count: Port Login Timeout: Port Down Retry Count: Port Down Timeout: Link Down Timeout: Port Number: Port Speed: Max Number of IOs per connection supported: Maximum number of Logins per port: Maximum number of exchanges: Maximum NPIV per port: Maximum number of FC Targets supported: Maximum number of outstand
PAGE 88
Table 62. Details of inlettemphistory (continued) NOTE: For FM120x4 systems, this subcommand provides the historical data for system board temperature. Synopsis Input ● racadm inlettemphistory export –f –t [–u ] [–p ] [-i ] ● racadm inlettemphistory get ● -f — Exports inlet temperature history filename. The maximum length of this parameter is 64 characters.
PAGE 89
jobqueue Table 63. Details of jobqueue Description Enables you to view and delete a job or jobs in the current Job Queue. NOTE: ● To run this subcommand, you must have the Server control privilege. ● If an unexpected error message is displayed for any operation, ensure you delete some jobs in the jobqueue and retry the operation. ● Use jobqueue create command after applying a pending device configuration. Else, you may see a job creation and deletion in the lclog.
PAGE 90
Table 63. Details of jobqueue (continued) ● Issue configuration changes for a PERC controller then start a real time job to execute the changes. racadm set RAID.Slot.3-1.RAIDdefaultWritePolicy WriteBack racadm set RAID.Slot.3-1.Name “Prod Workload” racadm jobqueue create RAID.Slot.3-1 –realtime ● Delete all possible jobs from the current job queue. racadm jobqueue delete --all ● Delete a specific job from the current job queue. racadm jobqueue delete -i ● To clear all the jobs in the job queue.
PAGE 91
lclog Table 65. Details of lclog Description Allows you to: ● Export the lifecycle log history. The log exports to remote or local share location. ● View the lifecycle log for a particular device or category. ● Add comment to a record in lifecycle log. ● Add a work note (an entry) in the lifecycle log. ● View the status of a configuration job. NOTE: ● When you run this command on Local RACADM, the data is available to RACADM as a USB partition and may display a pop-up message.
PAGE 92
Table 65. Details of lclog (continued) ● ● ● ● ● ● ● ● ● ● ● ● ○ Config ○ Updates ○ Audit -b —The subcategory used to filter the records. Provides multiple subcategories using a "," as the delimiter. -q—The sequence number from which the records must be displayed. Records older than this sequence number is displayed. NOTE: This parameter input is an integer. If an alphanumeric input is provided, then invalid subcommand syntax error is displayed.
PAGE 93
Table 65. Details of lclog (continued) ● Display the records under storage and system categories with severities set to warning or critical. racadm lclog view -c storage,system -s warning,critical ● Display the records having severities set to warning or critical, starting from sequence number 4. racadm lclog view -s warning,critical -q 4 ● Display 5 records starting from sequence number 20.
PAGE 94
license Table 66. Details of license Description Synopsis Input Manages the hardware licenses.
PAGE 95
License Bound Expiration = H1VGF2S = Not Applicable ● Import a new license to a specific device in a known location. $racadm license import -f license.xml -l //shareip/sharename -u -p -c idrac.embedded.1 ● Import a license from a CIFS share to a device, in this case Embedded iDRAC. racadm license import -u admin -p xxx -f License.xml -l //192.168.0/licshare -c idrac.embedded.1 ● Import a license from an NFS share to a device, in this case Embedded iDRAC.
PAGE 96
● Replace a license on a device with a license file on an NFS share using transaction ID. In this case, transaction 27. racadm license replace -f License.xml -l 192.168.0:/licshare -t 27 ● Replace a license on a device with a license file on a CIFS share using transaction ID. In this case, transaction 27. racadm license replace -u admin -p xxx -f License.xml -l //192.168.0/licshare -t 27 netstat Table 67. Details of netstat Description Display the routing table and network statistics.
PAGE 97
● To display the statistics for the integrated NIC, type the following command: $ racadm nicstatistics NIC.Integrated.1-1 Total Bytes Received: Total Bytes Transmitted: 0 0 Total Unicast Bytes Received: 0 Total Multicast Bytes Received: 0 Total Broadcast Bytes Received: 0 Total Unicast Bytes Transmitted: 0 ● To get the network statistics, type the following command: $ racadm nicstatistics NIC.Slot.5-2-1 : QLogic CNA Gigabit Ethernet-B8:AC:6F:B3:BF:10 NIC.Slot.
PAGE 98
ping6 Table 70. Details of ping6 attribute Description Verifies if the destination IPv6 address is reachable from iDRAC or with the current routing-table contents. A destination IPv6 address is required. Based on the current routing-table contents, an ICMP echo packet is sent to the destination IPv6 address. Verifies if the destination IPv6 address is reachable from CMC or with the current routing-table contents. A destination IPv6 address is required.
PAGE 99
Table 71. Details of RACADM Proxy (continued) ● The attribute racadm getconfig -g cfgractuning -o cfgRacTuneChassisMgmtAtServer must be set as non-zero in CMC. ● The attribute racadm get system.ChassisControl.ChassisManagement Monitoring attribute must be enabled in iDRAC. ● --proxy must be entered at the end of the command. ● Table 72. The root privilege is the default privilege for Local RACADM proxy.
PAGE 100
Table 71. Details of RACADM Proxy (continued) Input ● -u — Specifies the user name of the remote share that stores the catalog file. ● -p — Specifies the password of the remote share that stores the catalog file. ● -r — Specifies the iDRAC IP address connected to CMC. Example Local RACADM racadm getractime --proxy Remote RACADM racadm getractime -u root -p xxx -r 192.168.0 getractime --proxy racdump Table 73.
PAGE 101
Table 73.
PAGE 102
Host Name OS Name OS Version Power Status Fresh Air Capable = localhost.localdomain = = = ON = No Watchdog Information: Recovery Action = None Present countdown value = 478 seconds Initial countdown value = 480 seconds Embedded NIC MAC Addresses: NIC.Integrated.1-3-1 Ethernet NIC.Integrated.
PAGE 103
16233 16246 16247 26851 root root root root 40916 3824 3828 0 S S R SW racadm racdump sh -c /bin/ps /bin/ps [kworker/u:3] =============================================================================== RAC Firmware Build Log =============================================================================== BLD_TAG=idracfw_bldtag_2.05.05.05_691231_1800_00 BLD_VERSION=2.05.05.05 BLD_NUMBER=69.12.31 BLD_DATE=2.00.00.00.
PAGE 104
FanSpeed FanSpeed FanSpeed 7 8 9 Fan-7 Fan-8 Fan-9 OK Not OK OK 14521 1 4826 rpm rpm rpm 7250 14500 7250 14500 2344 14500 Temp 1 Ambient_Temp OK 21 celcius N/A PWR 1 PWR 2 PWR 3 PWR 4 PWR 5 PWR 6 PS-1 PS-2 PS-3 PS-4 PS-5 PS-6 40 Online OK Online OK Online OK Slot Empty N/A Failed OK Slot Empty N/A racreset Table 74. Details of racreset attribute Description Resets iDRAC.
PAGE 105
Table 74. Details of racreset attribute (continued) Example ● iDRAC reset racadm racreset ● To reset CMC. racadm racreset ● To reset server 1 racadm racreset -m server-1 ● To reset servers 1 and 3 racadm racreset -m server-1 -m server-3 racresetcfg Table 75. Details of racresetcfg attribute Description Deletes your current iDRAC configuration and resets iDRAC to the factory default settings. After reset, the default name and password are root and calvin, respectively, and the IP address is 192.168.0.120.
PAGE 106
Table 75. Details of racresetcfg attribute (continued) ● Force a reset of the iDRAC configuration to factory default. racadm racresetcfg -f ● Reset when vFlash Partition creation is in progress. racadm racresetcfg A vFlash SD card partition operation is in progress. Resetting the iDRAC may corrupt the vFlash SD card. To force racresetcfg, use the -f flag. remoteimage Table 76. Details of remoteimage attribute Description Connects, disconnects, or deploys a media file on a remote server.
PAGE 107
Table 76. Details of remoteimage attribute (continued) ● Disable Remote File Sharing. racadm remoteimage -d Disable Remote File Started. Please check status using -s option to know Remote File Share is ENABLED or DISABLED. ● Check Remote File Share status. racadm remoteimage -s Remote File Share is Enabled UserName Password ShareName //192.168.0/xxxx/dtk_3.3_73_Linux.iso ● Deploy a remote image on iDRAC CIFS Share. racadm remoteimage –c –u admin –p xxx –l 192.168.0.1:/dev/floppy.
PAGE 108
sensorsettings Table 78. Details of sensorsettings Description Allows you to perform threshold settings of the sensor. To run this subcommand, you must have Configure iDRAC privilege. NOTE: An error message is displayed when the following is performed: ● A set operation is performed on an unsupported FQDD. ● Out of range settings is entered. ● Invalid sensor FQDD is entered. ● Invalid threshold level filter is entered.
PAGE 109
Table 79. Details of serveraction attribute (continued) ● ● ● ● powerdown — Powers down the managed system. powerup — Powers up the managed system. powerstatus — Displays the current power status of the server (ON or OFF). graceshutdown — Performs a graceful shutdown of the server. If the operating system on the server cannot shut down completely, then this operation is not performed. ● nmi — Generates the Non-masking interrupt (NMI) to halt the system operation.
PAGE 110
set Table 80. Details of set Description Modifies the value of configuration objects on a component. The Set sub-command has two forms: ● The modification of a single object to a new value specified in the command line. ● The modification of multiple objects to new values using a configuration file. It supports multi-object value import from two configuration file formats.
PAGE 111
Table 80. Details of set (continued) Input ● racadm set -f -t xml -u -p -l [--preview] [--continue] ● racadm set -f -t xml -u -p -l -c [,*] ● Examples for FQDDs: ● ● ● ● ● ● ● ● ● ○ System.Power ○ System.Power.Supply ○ System.Location ○ LifecycleController.LCAttributes ○ System.LCD ○ iDRAC.Serial — Specifies the group containing the object that must be written.
PAGE 112
Table 80. Details of set (continued) The --preview option provides the Job ID to verify the status of the file preview operation. The Job ID can be tracked by running the racadm jobqueue view –I command. NOTE: ○ The --preview option does not restart the system. ○ The-b,-w options cannot be included with the --preview option. ○ A scheduled job or pending configuration should not be running while using the --preview option.
PAGE 113
Table 80. Details of set (continued) Multi-object Set of staged objects ● Configure a systems using a local Server Configuration Profile XML file containing a mix of real-time and staged objects; reboot the server gracefully with a wait time of ten minutes, leaving the server powered on after the reboot. racadm set -f myfile.xml -t xml -b "graceful" -w 600 -s "on" ○ Make note of the Job ID output by the Set command. ○ After reboot, wait for the job to complete by checking the job status.
PAGE 114
Table 81. Details of setled attribute (continued) Sets LED state on Chassis to Blink ● racadm setled -m server-1 -1 1 LED state was set successfully. ● racadm setled -m server-9 -1 1 ERROR: Server in slot 9 is an extension of the server in slot 1. NOTE: The setled command generates an error when run on the extension slot of a multi-slot server. ● From iDRAC stop LED from blinking. racadm setled -l 0 RAC0908: System ID LED blink off. ● From iDRAC start LED to blink.
PAGE 115
Table 82. Details of setniccfg attribute (continued) ● Input racadm setniccfg [-i ] -v [ ] ● -d — Enables DHCP for the NIC. It is enabled by default. ● -d6 — Enables AutoConfig for the NIC (default is disabled). ● -s — Enables static IP settings. The IPv4 address, netmask, and gateway must be specified. Otherwise, the existing static settings are used. , , and must be typed as dot-separated strings. racadm setniccfg -s 192.168.0 255.255.255.
PAGE 116
Table 82. Details of setniccfg attribute (continued) ● Configuration of CMC to a static IPv6 address. racadm setniccfg -m chassis -s -6 2001:DB8::2 64 2001:DB8::1 ● Configuration of server to use stateless autoconfiguration address. racadm setniccfg -m server-1 -d -6 ● Configuration of VLAN id and priority for a switch. racadm setniccfg -m switch-1 -v 1000 7 ● Removal of VLAN configuration from a switch.
PAGE 117
● Upload an invalid key to iDRAC User 2 in the first key space using a string. $ racadm sshpkauth -i 2 -k 1 -t "This is invalid key Text" ERROR: Key text appears to be corrupt ● Upload a valid key to iDRAC User 2 in the first key space using a file. $ racadm sshpkauth -i 2 -k 1 -f pkkey.key Key file successfully uploaded. ● Get all keys for User 2 on iDRAC.
PAGE 118
Table 84. Details of sslcertdownload attribute (continued) ● Download Active Directory certificate: racadm -r 192.168.0 -u root -p xxx sslcertdownload -t 2 -f ad_cert.txt NOTE: This command is not supported in the firmware RACADM interface as it is not a file system. sslcertupload Table 85. Details of sslcertupload attribute Description Uploads a custom SSL server or CA certificate for Directory Service from the client to iDRAC. To run this subcommand, you must have the Server Control privilege.
PAGE 119
Table 86. Details of sslcertview attribute (continued) ○ 1=server certificate ○ 2=Active Directory ● -A — Prevents printing headers or labels. NOTE: If a certificate is generated using comma ‘,’ as one of the parameters for the Organization Name, Common Name, Location Name, or State Name, then this command displays the partial name in the respective fields only up to the comma. The rest of the string is not displayed.
PAGE 120
Table 87. Output (continued) Valid To Jun 4 23:54:19 2021 GMT racadm sslcertview -t 1 -A 00 US Texas Round Rock Dell Inc. Remote Access Group iDRACCMC default certificate US Texas Round Rock Dell Inc. Remote Access Group iDRACCMC default certificate Jun 7 23:54:19 2011 GMT Jun 4 23:54:19 2021 GMT sslcertdelete Table 88. Details of sslcertdelete Description Command to delete a custom signing certificate from iDRAC. To run this subcommand, you must have the Server Control privilege.
PAGE 121
Table 88. Details of sslcertdelete (continued) ● The iDRAC resets and may be offline temporarily. Example Use Remote RACADM to delete the custom signing certificate. $ racadm -r 192.168.0 -u root -p xxx sslcertdelete -t 3 sslcsrgen Table 89. Details of sslcsrgen attribute Description Generates and downloads a certificate signing request (CSR) file to the client’s local file system. The CSR can be used for creating a custom SSL certificate that can be used for SSL transactions on iDRACCMC.
PAGE 122
NOTE: Before a CSR can be generated, the CSR fields must be configured in the RACADM config —g cfgracsecurity group. For example: racadm config -g cfgracsecurity -o cfgRacSecCsrCommonName cmc-effort.cmc.com NOTE: In Telnet or SSH console, you can only generate and not download the CSR file. NOTE: The duration for generating a CSR key depends on the length specified for the key. sslkeyupload Table 90. Details of sslkeyupload Description Uploads SSL key from the client to iDRAC.
PAGE 123
Table 92. Details of storage (continued) To run this subcommand for configuring the storage properties, you must have the server control permission. NOTE: You can also run the command using raid in place of the storage command.
PAGE 124
Table 92.
PAGE 125
Table 92.
PAGE 126
Table 92.
PAGE 127
Table 92. Details of storage (continued) -key -xxx -xxx racadm storage deletesecuritykey: racadm storage ccheck: racadm storage cancelcheck: ● To convert the physical disk drives and assign or delete a hotspare.
PAGE 128
Table 92. Details of storage (continued) -type option is not present, the global hotspare (ghs) is created by default.
PAGE 129
Table 92. Details of storage (continued) ● -wp{wt|wb|wbf}—Sets the write policy to Write Through, Write Back, or Write Back Force ● -rp {nra|ra|ara}—Sets the read policy to No Read Ahead, Read Ahead, Adaptive Read Ahead ● -ss—Specifies the stripe size to use. ● -pdkey:—Specifies the physical disk drive to use in the virtual disk. ● -dcp—Sets the Disk Cache Policy in the Virtual Disk. ○ enabled—Allows the virtual disk to use the cache.
PAGE 130
Table 92. Details of storage (continued) NOTE: To start the operation, the Controller.PatrolReadMode must be in Manual mode. ● -dstpd-replaces a physical disk in virtual disk configuration. ● -vd-virtual disk fqdd to make it as a bootable drive. ● -speed—Specifies the initialization of the Virtual disk. ○ fast—Performs fast initialization. ○ full—Performs slow initialization. ● blink: or unblink: — can be physical disk drives, virtual disks, or PCIeSSD.
PAGE 131
-------------------------------------------------------------------------------Usage Examples racadm storage racadm storage racadm storage racadm storage racadm storage racadm storage racadm storage racadm storage racadm storage racadm storage racadm storage racadm storage racadm storage racadm storage racadm storage racadm storage : get get get get get get get get get get get get get get get get controllers psus controllers -o controllers -o -current controllers -o -pending enclosures -o controllers -o -
PAGE 132
SlotType MaxCapableSpeed LearnMode T10PICapability SupportRAID10UnevenSpans SupportEnhancedAutoForeignImport EnhancedAutoImportForeignConfig SupportControllerBootMode ControllerBootMode RealtimeConfigurationCapability CurrentControllerMode BootVD = = = = = = = = = = = = Unknown 12.0 Gb/s Not supported Capable Supported Supported Enabled Supported Continue Boot On Error Capable RAID Disk.Virtual.0:RAID.Integrated.
PAGE 133
The following command displays the output for PowerEdge FD332 support and full controller objects along with their keys: racadm storage get controllers -o RAID.Modular.
PAGE 134
CopybackMode PreservedCache CacheMemorySize PersistHotspare SpindownUnconfiguredDrives SpindownHotspare Timeintervalforspindown SecurityStatus EncryptionMode SasAddress PciDeviceId PciSubdeviceId PciVendorId PciSubvendorId PciBus PciDevice PciFunction BusWidth SlotLength SlotType MaxCapableSpeed LearnMode T10PICapability SupportRAID10UnevenSpans SupportEnhancedAutoForeignImport EnhancedAutoImportForeignConfig SupportControllerBootMode RealtimeConfigurationCapability CurrentControllerMode BootVD = = = = = =
PAGE 135
The following command displays all virtual disk keys connected to the controllers: racadm storage get vdisks --refkey RAID.Integrated.1-1 Disk.Virtual.0:RAID.Integrated.1-1 The following command is an optimized and filtered version: racadm storage get vdisks -o -p DeviceDescription,OperationalState Disk.Virtual.0:RAID.Integrated.1-1 DeviceDescription = Virtual Disk 0 on Integrated raid Controller 1 OperationalState = Not applicable ○ Table 93.
PAGE 136
Table 93. To generate and view information about the inventory of virtual disks (continued) Secured NO RemainingRedundancy 0 EnhancedCache Not Applicable T10PIStatus Disabled BlockSizeInBytes 512 ○ Table 94. To generate and view information about the inventory of storage enclosures Status Ok State Ready DeviceDescription Backplane 1 on Connector 0 of Integrated RAID Controller 1 RollupStatus Ok Name BP13G+EXP 0:1 BayId 1 FirmwareVersion 0.
PAGE 137
RemainingRatedWriteEndurance SecurityStatus BusProtocol MediaType UsedRaidDiskSpace AvailableRaidDiskSpace Hotspare Manufacturer ProductId Revision SerialNumber PartNumber NegotiatedSpeed ManufacturedDay ManufacturedWeek ManufacturedYear SasAddress FormFactor RaidNominalMediumRotationRate T10PICapability BlockSizeInBytes MaxCapableSpeed = = = = = = = = = = = = = = = = = = = = = = Not Applicable Not Capable SAS HDD 136.13 GB 0.00 GB NO SEAGATE ST9600204SS FM08 6WN09DXN CN07T0DW7262211M01Y6A00 6.
PAGE 138
MaxCapableSpeed ForeignKeyIdentifier = 6 Gb/s = dellkey1 The following command is an optimized and filtered version: racadm storage get pdisks --refkey Enclosure.Internal.0-1:RAID.Integrated.1-1 -o -p State Disk.Bay.0:Enclosure.Internal.0-1:RAID.Integrated.1-1 State = Online ○ To generate and view information about the inventory of fans connected to the enclosure.
PAGE 139
○ The following command provides the properties of the specified PCIeSSD enclosure: racadm storage get enclosures:Enclosure.Internal.0-1:PCIeExtender.Slot.3 Enclosure.Internal.0-1:PCIeExtender.Slot.3 RollupStatus = Ok DeviceDescription = Enclosure.Internal.0-1:PCIeExtender.Slot.3 Name = PCIe SSD BP 1 SlotCount = 4 FirmwareVersion = 0.80 ○ To get the list of physical disks and properties of the specified PCIeSSD physical disk.
PAGE 140
● To view the help details for a configuration command, run the following command: admin1-> racadm storage help createvd Storage configuration of hardware RAID connected to the system.
PAGE 141
○ The following command encrypts the specified virtual disk: racadm storage encryptvd:Disk.Virtual.0:RAID.Integrated.1-1 NOTE: Virtual disk must be created with SED. ○ The following command assigns security key for controller: racadm storage createsecuritykey:RAID.Integrated.1-1 -key -xxx ○ The following command modifies security key for controller: racadm storage modifysecuritykey:RAID.Integrated.
PAGE 142
● To prepare the specified PCIeSSD device for removal, run the following command: racadm storage preparetoremove: Disk.Bay.8:Enclosure.Internal.0-1:PCIeExtender.Slot.3 STOR089 : Successfully accepted the storage configuration operation. To apply the configuration operation, create a configuration job with --realtime option. To create the required commit jobs, run the jobqueue command.
PAGE 143
Table 95. Details of swinventory (continued) Output racadm swinventory ------------------SOFTWARE INVENTORY------------------ComponentType = FIRMWARE ElementName = Power Supply.Slot.2 FQDD = PSU.Slot.2 InstallationDate = 2013-06-11T13:02:46Z Current Version = 07.2B.7D --------------------------------------------------------------ComponentType = FIRMWARE ElementName = Integrated Remote Access Controller FQDD = iDRAC.Embedded.1-1 InstallationDate = NA Rollback Version = 1.50.
PAGE 144
Table 96. Details of systemconfig (continued) ● To view an AutoBackup Schedule. racadm systemconfig getbackupscheduler ● To delete an AutoBackup Schedule. racadm systemconfig clearbackupscheduler NOTE: After the parameters are cleared, the AutoBackupScheduler is disabled. To schedule the backup again, enable the AutoBackupScheduler. Input ● -n — Specifies a pass phrase used to encrypt or decrypt the configuration data. The pass phrase must have 8 to 32 characters, and one upper and lower case character.
PAGE 145
Table 96. Details of systemconfig (continued) ● Back up system to NFS share and encrypt the data. racadm systemconfig backup -f image.img -l 192.168.0 :/share -u admin -p xxx -n Encryptp@sswd123 ● Back up system to vFlash SD. racadm systemconfig backup --vFlash ● Restore system from vFlash SD and clear the VD configurations. racadm systemconfig restore -vFlash --nopreserve ● Restore system from NFS share without clearing the VD configurations. racadm systemconfig restore -f image.img -l 192.168.
PAGE 146
Table 97. Details of systemerase (continued) ○ drvpack ○ idrac ○ lcdata Examples ● racadm systemerase bios ● racadm systemerase diag ● racadm systemerase drvpack ● racadm systemerase idrac ● racadm systemerase lcdata ● racadm systemerase bios,diag,drvpack ● racadm systemerase bios,idrac,lcdata systemperfstatistics Table 98. Details of systemperfstatistics Description Allows you to view and manage the system performance monitoring operations.
PAGE 147
Average Readings Last Hour = 0% Last Day = 0% Last Week = 0% Peak Readings Last Week 0% [At Mon, 05 May 2014 15:58:35] ● To reset the peak utilization of a specific sensor racadm systemperfstatistics PeakReset iDRAC.Embedded.1#SystemBoardCPUUsageStat RAC1163: The peak utilization value of Out-Of-Band performance monitoring sensor CPU Usage is successfully reset. techsupreport Table 99. Details of techsupreport Description Allows you to perform the technical support report operations.
PAGE 148
Table 99. Details of techsupreport (continued) ○ TTYLog — TTYLog data NOTE: ○ For updating the operating system application data collection, enter the value OSAppNoPII or OSAppAll to the -t option. ○ If no value is specified then system information data is collected. ○ To perform the Oslog collection, make sure that ISM is installed and running. ● ● ● ● ○ TTYLog includes PCIeSSD data.
PAGE 149
Table 100. Details of testemail attribute (continued) Output Success: Test e-mail sent successfully Failure: Unable to send test e-mail Example Commands for the idrac.EmailAlert group: ● Enable the alert. racadm set idrac.EmailAlert.1.Enable 1 ● Set the destination email address. racadm set idrac.EmailAlert.1.Address user1@mycompany.com ● Set the custom message that is sent to the destination email address. racadm set idrac.emailalert.1.
PAGE 150
Table 101. Details of testtrap attribute (continued) ● View the current test trap settings. racadm get iDRAC.SNMP.Alert. where is a number from 1 to 8 ● Send a test trap to the destination configured for index 1: racadm testtrap -i 1 testalert Table 102. Details of testalert Description Tests FQDN supported SNMP trap notifications. To run this subcommand, you must have the Test Alert User Access. Synopsis Input racadm testalert -i -i — Specifies the index of the trap test.
PAGE 151
Table 103. Details of traceroute attribute (continued) Output traceroute to 192.168.0.1 (192.168.0.1), 30 hops max, 40 byte packets 1 192.168.0.1 (192.168.0.1) 0.801 ms 0.246 ms 0.253 ms traceroute6 Table 104. Details of traceroute6 attribute Description Traces the network path of routers as the packets traverse from the system to a destination IPv6 address. To run this subcommand, you must have the Administrator privilege. To run this subcommand, you must have the Execute Diagnostic Commands permission.
PAGE 152
Table 105.
PAGE 153
Table 105. Details of update (continued) For devices that perform update process without rebooting the host, the update status changes from Downloading to Completed. For devices that require host reboot to perform update process, the update status changes from Downloading to Scheduled. When the status is displayed as Scheduled, reboot the host to start the update process.
PAGE 154
Table 105. Details of update (continued) ● Perform update from a CIFS repository and reboot the server to apply the updates. racadm update -f Catalog.xml -l //192.168.11.10/Repo -u admin -p mypass -a TRUE -t CIFS ● Generate a comparison report using about the available updates in the repository. racadm update -f Catalog.xml -l 192.168.11.10:/Repo -t NFS -a FALSE -verifycatalog ● Perform update from an FTP repository and reboot the server to apply the updates. racadm update -f Catalog.xml -e 192.168.11.
PAGE 155
Table 106. Details of usercertupload (continued) Input ● -t — Specifies the type of certificate to upload, either the CA certificate or server certificate. ○ 1=user certificate ○ 2=user CA certificate ● -f — Specifies the filename of the certificate that must be uploaded. If the file is not specified, the sslcert file in the current directory is selected. ● -i — Index number of the user. Valid values 2–16. Output If upload is successful, the message User certificate successfully uploaded to the RAC.
PAGE 156
vflashsd Table 108. Details of vflashsd Description Allows you to initialize or get the status of the vFlash SD card. The initialize operation removes all the existing partitions and resets the card. The status operation displays the status of the last operation performed on the card. To run this subcommand, you must have the Access Virtual Media privilege. NOTE: After you restart the iDRAC, the status of the previous initialize operation is erased.
PAGE 157
Table 109. Details of vflashpartition (continued) ○ The user name or password provided is not correct. ○ The file provided does not exist. ○ The memory available on the SD card is lesser than size of the image file. ● ● ● ● ● Example -l — Specifies the remote path relative to iDRAC. -u — User name for accessing the remote image. -p — Password for accessing the remote image. -a — Display the status of operations on all the existing partitions. list — Lists the existing partitions and its properties.
PAGE 158
3 iDRAC Property Database Group and Object Descriptions The iDRAC property database contains the configuration information for iDRAC. Associated object is organizing data, and object group is organizing object. The IDs for the groups and objects that the property database supports are listed in this section for iDRAC Enterprise on Blade Servers and iDRAC Enterprise or Express on Rack and Tower Servers. To configure iDRAC, use the group and object IDs with the RACADM subcommands.
PAGE 159
• • • • • cfgSensorRedundancy cfgVFlashSD cfgVFlashPartition cfgLogging cfgRacSecurity Displayable Characters Displayable characters include the following set: abcdefghijklmnopqrstuvwxwz ABCDEFGHIJKLMNOPQRSTUVWXYZ 0123456789~`!@#$%^&*()_+-={}[]|\:";'<>,.?/ Table 111.
PAGE 160
Table 111.
PAGE 161
idRacDescriptionInfo (Read Only) Table 113. Details of Read only attribute - idRacDescriptionInfo Description A text description of the RAC type. Legal Values A string of up to 255 ASCII characters. Default This system component provides a complete set of remote management functions for Dell PowerEdge servers. idRacVersionInfo (Read Only) Table 114.
PAGE 162
Table 117.
PAGE 163
Table 119. Details of cfgNicStaticIPv4Enable (continued) Legal Values ● 0 — Disabled ● 1 — Enabled Default 1 — Enabled NOTE: If this object is modified, then the object cfgNicIPv4Enable is also modified. cfgNicStaticIpAddress (Read or Write) Table 120. Details of cfgNicStaticIpAddress Description Returns or sets the current IPv4 address. NOTE: Only set the current IPv4 address if cfgNicUseDhcp is set to 0(false). Legal Values Any Valid IPv4 address Default 192.168.
PAGE 164
cfgDNSStaticServersFromDHCP (Read or Write) Table 124. Details of cfgDNSStaticServersFromDHCP Description Specifies the DNS server static IP addresses. Legal Values ● DNS Addresses are configured on the Device ● DNS Addresses are assigned via DHCP Default 0 cfgDNSStaticServer1 (Read or Write) Table 125. Details of cfgDNSStaticServer1 Description Specifies the IP address for DNS server 1. NOTE: This property is only valid if cfgDNSServersFromDHCP is set to 0 (FALSE).
PAGE 165
Table 128. Details of cfgDNSStaticDomainNameFromDHCP (continued) Legal Values ● 0 — Do not use DHCP to get the Domain Name ● 1 — Use DHCP to get the Domain Name Default 0 — Disabled cfgRemoteHosts This group provides properties that allow configuration of the SMTP server for email alerts. This group enables/disables and configures firmware updates, NTP, remote syslogging and SMTP email alerting. To apply this setting to iDRAC, use the —m option. Use this object with the config or getconfig subcommands.
PAGE 166
cfgRhostsSmtpServerIpAddr (Read or Write) Table 132. Details of attribute - cfgRhostsSmtpServerIpAddr Description The IPv4 or IPv6 address of the network SMTP server. The SMTP server transmits email alerts from iDRAC if the alerts are configured and enabled. The SMTP server transmits email alerts from CMC if the alerts are configured and enabled. Legal Values A string representing a valid SMTP server IPv4 or IPv6 address. For example: 192.168.0.2. Default For IPv4, it is 0.0.0.0 localhost.
PAGE 167
cfgRhostsSyslogServer2 Read or Write) Table 136. Details of attribute - cfgRhostsSyslogServer2 Description To store the RAC and SEL logs Specify the second of three possible remote syslog servers. This property is only valid if cfgRhostsSyslogEnable is set to 1 (enabled). Legal Values String from 0 to 63 characters. Valid host name or IPv4 or IPv6 address. Default cfgRhostsSyslogServer3 Read or Write) Table 137.
PAGE 168
Table 138. Details of cfgUserAdminIndex attribute (continued) Default cfgUserAdminIpmiLanPrivilege (Read or Write) Table 139. Details of cfgUserAdminIpmiLanPrivilege Description The maximum privilege on the IPMI LAN channel. Legal Values ● ● ● ● Default ● 4(User 2) ● 15(All others) 2(User) 3(Operator) 4(Administrator) 15(No access) cfgUserAdminIpmiSerialPrivilege (Read or Write) Table 140.
PAGE 169
Table 142.
PAGE 170
Table 143. Examples (continued) access iDRAC or CMC The user may only log in to iDRAC or CMC and view iDRAC or CMC and server configuration information. 0x00000001 The user may log 0x00000001 + 0x00000002 = 0x00000003 in to iDRAC or CMC and change configuration. The user may log in to iDRAC, access Virtual Media, and Virtual Console. 0x00000001 + 0x00000040 + 0x00000080 = 0x000000C1 cfgUserAdminUserName - Read or Write Table 144.
PAGE 171
Table 146. Details of cfgUserAdminEnable attribute (continued) Legal Values ● 1 (TRUE) ● 0(FALSE) Default 1 (User 2), 0 (All others) 0 cfgUserAdminSolEnable (Read or Write) Table 147. Details of cfgUserAdminSolEnable Description Enables or disables Serial Over LAN (SOL) user access for the user. Legal Values ● 1 (TRUE) ● 0(FALSE) Default 0 cfgEmailAlert This group contains parameters to configure iDRAC email alerting capabilities. Up to four instances of this group are allowed.
PAGE 172
cfgEmailAlertAddress - Read or Write Table 150. Details of cfgEmailAlertAddress attribute Description Specifies the destination email address for email alerts, for example, user1@company.com. Legal Values Email address format, with a maximum length of 64 ASCII characters. Default cfgEmailAlertCustomMsg (Read or Write) Table 151. Details of cfgEmailAlertCustomMsg Description Specifies a custom message that forms the subject of the alert.
PAGE 173
Table 153. Details of cfgSsnMgtRacadmTimeout attribute (continued) Legal Values 10–1920 Default 60 30 minutes Example racadm getconfig -g cfgSessionManagement cfgSsnMgtWebserverTimeout=0 cfgSsnMgtTelnetIdleTimeout=0 cfgSsnMgtSshIdleTimeout=1800 cfgSsnMgtRacadmTimeout=0 cfgSsnMgtConsRedirMaxSessions (Read or Write) Table 154. Details of cfgSsnMgtConsRedirMaxSessions Description Specifies the maximum number of Virtual Console sessions allowed on iDRAC.
PAGE 174
Table 156. Details of cfgSsnMgtSshIdleTimeout attribute (continued) Default ● For iDRAC on Rack and Tower Servers: 300 ● For iDRAC Enterprise on Blade Servers: 1800 1800 cfgSsnMgtTelnetIdleTimeout - Read or Write Table 157. Details of cfgSsnMgtTelnetIdleTimeout attribute Description Defines the Telnet idle timeout. This property sets the amount of time in seconds that a connection is allowed to remain idle (there is no user input). The session is canceled if the time limit exceeds this property.
PAGE 175
cfgSerialConsoleEnable - Read or Write Table 159. Details of cfgSerialConsoleEnable attribute Description Enables or disables the serial console interface. Legal Values ● 1 (TRUE) ● 0 (FALSE) Default 0 1 cfgSerialConsoleQuitKey (Read or Write) Table 160. Details of cfgSerialConsoleQuitKey attribute Description This key or key combination terminates Virtual Console text for iDRAC when using the console com2 command.
PAGE 176
Table 162. Details of cfgSerialConsoleNoAuth attribute (continued) ● 1 — (disables serial login authentication) Default 0 cfgSerialConsoleCommand - Read or Write Table 163. Details of cfgSerialConsoleCommand attribute Description Specifies a serial command that is executed after a user logs in to the serial console interface. Legal Values A string of up to 128 characters. A string representing a valid serial command. For example, connect server-1.
PAGE 177
cfgSerialSshEnable - Read or Write Table 167. Details of cfgSerialSshEnable attribute Description Enables or disables the secure shell (SSH) interface. Legal Values ● 1 (TRUE) ● 0 (FALSE) Default 1 Example racadm getconfig -g cfgSerial cfgSerialBaudRate=115200 cfgSerialConsoleEnable=1 cfgSerialConsoleQuitKey=^\ cfgSerialConsoleIdleTimeout=1800 cfgSerialConsoleNoAuth=0 cfgSerialConsoleCommand= cfgSerialConsoleColumns=0 cfgSerialHistorySize=8192 cfgSerialTelnetEnable=0 cfgSerialSshEnable=1 cfgSerialTel
PAGE 178
cfgOobSnmpAgentCommunity (Read or Write) Table 169. Details of cfgOobSnmpAgentCommunit attribute Description Specifies the SNMP Community Name used for SNMP traps. The community string acts as a password shared between different hosts over the network. This community string value must match with the other hosts for any kind of communication through SNMP. Legal Values A string of up to 31 characters.
PAGE 179
cfgRacTuneConRedirPort (Read or Write) Table 171. Details of cfgRacTuneConRedirPort Description To use for keyboard, mouse, video and Virtual Media traffic to iDRAC, specify the port. Legal Values 1024–65535 Default 5900 cfgRacTuneRemoteRacadmEnable (Read or Write) Table 172. Details of cfgRacTuneRemoteRacadmEnable attribute Description Enables or disables the Remote RACADM interface. Legal Values ● 1 (TRUE) ● 0 (FALSE) Default 1 cfgRacTuneCtrlEConfigDisable Table 173.
PAGE 180
Table 175. Details of cfgRacTuneHttpsPort attribute (continued) NOTE: The following port numbers are reserved and cannot be used: 21, 68, 69, 111, 123, 161, 546, 801, 4096, 5988, 5989, 6900, 9000, and 60106. Default 443 cfgRacTuneIpRangeEnable (Read or Write) Table 176. Details of cfgRacTuneIpRangeEnable attribute Description Enables or disables the IPv4 Address Range validation feature. Legal Values ● 1 (TRUE) ● 0 (FALSE) Default 0 cfgRacTuneIpRangeAddr (Read or Write) Table 177.
PAGE 181
Table 179. Details of cfgRacTuneSshPort attribute (continued) Legal Values 1–65535 10–65535 Default 22 cfgRacTuneTelnetPort (Read or Write) Table 180. Details of cfgRacTuneTelnetPort attribute Description Specifies the port number used for the Telnet interface. NOTE: The following port numbers are reserved and cannot be used: 21, 68, 69, 111, 123, 161, 546, 801, 4096, 5988, 5989, 6900, 9000, and 60106. Legal Values 1–65535 10–65535 Default 23 cfgRacTuneConRedirEnable (Read or Write) Table 181.
PAGE 182
cfgRacTuneDaylightOffset (Read Only) Table 184. Details of cfgRacTuneDaylightOffset attribute Description Specifies the daylight savings offset (in minutes) to use for the RAC Time. This value is 0 if the time zone is not a Daylight Saving time zone.
PAGE 183
cfgRacTuneSshPort=22 cfgRacTuneIpRangeEnable=0 cfgRacTuneIpRangeAddr=192.168.1.1 cfgRacTuneIpRangeMask=255.255.255.0 # cfgRacTuneTimezoneOffset=-18000 # cfgRacTuneDaylightOffset=3600 cfgRacTuneLocalServerVideo (Read or Write) Table 186. Details of cfgRacTuneLocalServerVideo Description Enables or disables the local server video. Legal Values ● 1 (TRUE — Enables) ● 0 (FALSE— Disables) Default 1 cfgRacTuneLocalConfigDisable (Read or Write) Table 187.
PAGE 184
Table 189. Details of cfgRacTuneVirtualConsoleAuthorizeMultipleSessions (continued) Legal Values 0 — (If the user of the first session has not responded for session sharing request by subsequent user. The next session user gets an access denied error after the default timeout value of 30 seconds.) 1 — (If the user of the first session has not responded for session sharing request by subsequent user. The next session user gets a read-only access after the default timeout value of 30 seconds.
PAGE 185
cfgVirMediaAttached (Read or Write) Table 193. Details of cfgVirMediaAttached Description This object is used to attach virtual devices to the system via the USB bus. When the devices are attached, the server recognizes valid USB mass storage devices attached to the system. Which is equivalent to attaching a local USB CDROM/floppy drive to a USB port on the system. When the devices are attached, they can be connected to the virtual devices remotely using iDRAC web interface or the CLI.
PAGE 186
Table 196. Details of cfgSDWriteProtect (continued) cfgSDWriteProtect command is successful, use the cfgVFlashSDWriteProtect command. For more information, see cfgVFlashSDWriteProtect Read Only. Legal Values ● 1 (TRUE) ● 0(FALSE) Default 0 cfgServerInfo This group allows you to select the BIOS first boot device and provides the option to start the selected device only once. This group allows you to display and configure a server in the chassis. Use this object with the config or getconfig subcommands.
PAGE 187
cfgServerDNSIMCName (Read or Write) Table 200. Details of cfgServerDNSIMCName attribute Description Displays the DNS domain name for iDRAC or IMC. Legal Values A valid string values Default None Usage You can get and set the iDRAC DNS name using the cfgServerDNSIMCName attribute.
PAGE 188
Table 201. Details of cfgServerFirstBootDevice (continued) NOTE: First attach, to configure vFlash as First Boot Device.
PAGE 189
Use this object with the config or getconfig subcommands. To use this object property, you must have the Chassis Configuration Administrator privilege. NOTE: You can configure a setting that does not have the hash sign (#) prefixed in the output. To modify a configurable object, use the —o option. The following sections provide information about the objects in the cfgActiveDirectory. cfgADSSOEnable (Read or Write) Table 203.
PAGE 190
cfgADRacName (Read or Write) Table 207. Details of cfgADRacName attribute Description Name of iDRAC as recorded in the Active Directory forest. Name of CMC as recorded in the Active Directory forest. Legal Values Any printable text string of up to 254 characters, with no white space. Default cfgADRacDomain (Read or Write) Table 208. Details of cfgADRacDomain attribute Description Active Directory Domain in which iDRAC resides. Active Directory Domain in which CMC resides.
PAGE 191
cfgADType (Read or Write) Table 211. Details of cfgADType attribute Description To use the Active Directory, determine the schema type. Legal Values ● 1— (Enables Active Directory with the extended schema) ● 2— (Enables Active Directory with the standard schema) Default 1 cfgADGlobalCatalog1 (Read or Write) Table 212. Details of cfgADGlobalCatalog1 Description To obtain user names, specify the Global Catalog server from which you want the iDRAC. This object is applicable only to iDRAC.
PAGE 192
Table 215. Details of cfgADCertValidationEnable attribute (continued) ● 0 (FALSE) Default 1 cfgADDcSRVLookupEnable (Read or Write) Table 216. Details of cfgADDcSRVLookupEnable Description Configures iDRAC to use pre‑configured domain controllers or to use DNS to find the domain controller. If using pre‑configured domain controllers, then the domain controllers to use are specified under cfgAdDomainController1 ,cfgAdDomainController2 and cfgAdDomainController3.
PAGE 193
Table 219. Details of cfgADGcSRVLookupEnable (continued) Legal Values ● 0(FALSE) — use pre‑configured Global Catalog Servers (GCS) ● 1(TRUE) — use DNS to look up GCS Default 0 cfgADGcRootDomain (Read or Write) Table 220. Details of cfgADGcRootDomain Description The names of the Active Directory root domain used for DNS look up, to locate Global Catalog servers. This object is applicable only to iDRAC. Legal Values String.
PAGE 194
Table 222. Details of cfgLDAPServer attribute (continued) Maximum length = 254 Default Null cfgLDAPPort (Read or Write) Table 223. Details of cfgLDAPPort attribute Description Port of LDAP over SSL. Non-SSL port is not supported. Legal Values 1–65535 Default 636 cfgLDAPBaseDN (Read or Write) Table 224. Details of cfgLDAPBaseDN attribute Description The domain name of the branch of the directory where all searches must start. Legal Values String.
PAGE 195
cfgLDAPGroupAttributeIsDN (Read or Write) Table 227. Details of cfgLDAPGroupAttributeIsDN attribute Description When it is set to 1, iDRAC compares the userDN retrieved from the directory to compare to the members of the group. If it is set to 0, the user name provides the login user to compare to the members of the group. It does not affect the search algorithm for the bind. iDRAC always searches the userDN and uses the userDN to bind.
PAGE 196
cfgLDAPCertValidationEnable (Read or Write) Table 231. Details of cfgLDAPCertValidationEnable attribute Description Controls certificate validation during SSL handshake. Legal Values ● 1 (TRUE) — Uses the CA certificate to validate the LDAP server certificate during SSL handshake. ● 0 (FALSE) —Skips the certificate validation step of SSL handshake. Default 1 cfgLDAPSRVLookupDomainName (Read Only) Table 232.
PAGE 197
cfgLDAPRoleGroupIndex (Read Only) Table 234. Details of cfgLDAPRoleGroupIndex attribute Description It is the index value of the Role Group Object. Legal Values An integer between 1 and 5 Default cfgLdapRoleGroupDN (Read or Write) Table 235. Details of cfgLdapRoleGroupDN Description It is the Domain Name of the group in this index. Configures the LDAP distinguished name (DN) for the role group instance. Legal Values String.
PAGE 198
cfgSSADRoleGroupIndex (Read Only) Table 237. Details of cfgSSADRoleGroupIndex attribute Description Index of the Role Group as recorded in the Active Directory. Legal Values An integer from 1 to 5 Default cfgSSADRoleGroupName (Read or Write) Table 238. Details of cfgSSADRoleGroupName attribute Description Name of the Role Group as recorded in the Active Directory forest. Legal Values Any printable text string of up to 254 characters, with no white space.
PAGE 199
Table 241. Example (continued) Access Virtual Media 0x00000040 Test Alerts 0x00000080 Execute Debug Commands 0x00000100 cfgThermal This group displays and configures the thermal settings. Use this object with the config or getconfig subcommands. To set the configurations, you must have the Chassis Configuration Administrator privileges. cfgThermalEnhancedCoolingMode (Read or Write) Table 242. Details of cfgThermalEnhancedCoolingMode attribute Description Configures the enhanced cooling mode.
PAGE 200
cfgIpmiSolMinPrivilege (Read or Write) Table 245. Details of cfgIpmiSolMinPrivilege Description Specifies the minimum privilege level required for SOL access. Legal Values ● 2(User) ● 3(Operator) ● 4(Administrator) Default 4 cfgIpmiSolAccumulateInterval (Read or Write) Table 246. Details of cfgIpmiSolAccumulateInterval Description Specifies the typical amount of time that iDRAC waits before transmitting a partial SOL character data packet. This value is 1-based 5ms increments.
PAGE 201
cfgIpmiLanPrivLimit (Read or Write) Table 249. Details of cfgIpmiLanPrivLimit Description Specifies the maximum privilege level allowed for IPMI over LAN access. Legal Values ● 2(User) ● 3(Operator) ● 4(Administrator) \Default 4 cfgIpmiLanAlertEnable (Read or Write) Table 250. Details of cfgIpmiLanAlertEnable Description Enables or disables global email alerting. This property overrides all individual email alerting enable or disable properties.
PAGE 202
cfgIpmiPetIPv6Index (Read Only) Table 253. Details of cfgIpmiPetIPv6Index Description Unique identifier for the index corresponding to the trap. Legal Values 1–4 Default cfgIpmiPetIPv6AlertDestIpAddr Table 254. Details of cfgIpmiPetIPv6AlertDestIpAddr Description Configures the IPv6 alert destination IP address for the trap. Legal Values IPv6 address Default cfgIpmiPetIPv6AlertEnable (Read or Write) Table 255.
PAGE 203
cfgIpmiPefIndex (Read or Write) Table 257. Details of cfgIpmiPefIndex Description Specifies the index of a specific platform event filter. Legal Values ● For iDRAC on Rack and Tower Servers: 1–22 ● For iDRAC Enterprise on Blade Servers: 1–9 Default The index value of a platform event filter object. cfgIpmiPefAction (Read or Write) Table 258. Details of cfgIpmiPefAction Description Specifies the action that is performed on the managed server when the alert is triggered.
PAGE 204
cfgIpmiPetAlertDestIpAddr (Read/Write) Table 261. Details of cfgIpmiPetAlertDestIpAddr Description Specifies the destination IPv4 address for the trap receiver on the network. The trap receiver receives an SNMP trap when an event is triggered on the managed server. Legal Values A string representing a valid IPv4 address. For example, 192.168.0.67. Default 0.0.0.0 cfgIpmiPetAlertEnable (Read or Write) Table 262. Details of cfgIpmiPetAlertEnable Description Enables or disables a specific trap.
PAGE 205
cfgServerPowerStatus (Read Only) Table 265. Details of cfgServerPowerStatus Description Represents the server power state, either ON or OFF. Legal Values ● 1 (ON) ● 0 (OFF) Default 0 cfgServerPowerAllocation (Read Only) Table 266. Details of cfgServerPowerAllocation Description Represents the available allocated power supply for server usage. NOTE: If there is more than one power supply, this object represents the minimum capacity power supply.
PAGE 206
Table 269. Details of cfgServerMinPowerCapacity (continued) Legal Values Not applicable Default cfgServerMaxPowerCapacity (Read Only) Table 270. Details of cfgServerMaxPowerCapacity Description Represents the maximum server power capacity based on the current component consumption. Legal Values Not applicable Default cfgServerPeakPowerConsumption (Read Only) Table 271.
PAGE 207
Table 274. Details of cfgServerPowerCapWatts (continued) Legal Values None Default Server power threshold in Watts. cfgServerPowerCapBtuhr (Read or Write) Table 275. Details of cfgServerPowerCapBtuhr Description Represents the server power threshold in BTU/hr. NOTE: This value is applicable only if cfgServerPowerCapEnable is set to 1. Legal Values None Default Server power threshold in BTU/hr. cfgServerPowerCapPercent (Read or Write) Table 276.
PAGE 208
cfgServerPowerLastWeekAvg (Read Only) Table 279. Details of cfgServerPowerLastWeekAvg Description Displays the average power value during the last week. Legal Values None Default Average power value during the last week. cfgServerPowerLastHourMinPower (Read Only) Table 280. Details of cfgServerPowerLastHourMinPower Description Displays the minimum power value during the last hour. Legal Values Not applicable Default Minimum power value during the last hour.
PAGE 209
cfgServerPowerLastHourMaxTime (Read Only) Table 283. Details of cfgServerPowerLastHourMaxTime Description Displays the timestamp of maximum power value during the last hour. Legal Values Time in the format: DD MM Date HH:MM:SS YYYY where, ● ● ● ● ● ● ● Default DD= Day of the week MM= Month Date=Date YYYY = Year HH = hour MM=Minutes SS = Seconds Maximum power value during the last hour. cfgServerPowerLastDayMinPower (Read Only) Table 284.
PAGE 210
Table 286. Details of cfgServerPowerLastDayMaxPower (continued) Default Maximum power value during the last day. cfgServerPowerLastDayMaxTime (Read Only) Table 287. Details of cfgServerPowerLastDayMaxTime Description Displays the timestamp of maximum power value during the last day.
PAGE 211
cfgServerPowerLastWeekMaxPower (Read Only) Table 290. Details of cfgServerPowerLastWeekMaxPower Description Displays the maximum power value during the last week. Legal Values None Default Maximum power value during the last week. cfgServerPowerLastWeekMaxTime (Read Only) Table 291. Details of cfgServerPowerLastWeekMaxTime Description Displays the timestamp of maximum power value during the last week. Legal Values A string of up to 32 characters.
PAGE 212
cfgServerActualAmperageConsumption (Read Only) Table 294. Details of cfgServerActualAmperageConsumption Description Displays the current power consumption. Legal Values Not applicable Default Current power consumption. cfgServerPeakAmperage (Read Only) Table 295. Details of cfgServerPeakAmperage Description Displays the current peak power consumption. Legal Values Not applicable Default Current peak power consumption. cfgServerPeakAmperageTimeStamp (Read Only) Table 296.
PAGE 213
cfgServerCumulativePowerConsumptionTimeStamp (Read Only) Table 298. Details of cfgServerCumulativePowerConsumptionTimeStamp Description Displays the timestamp of the cumulative power consumption. Legal Values A string of up to 32 characters. Time in the format: DD MM Date HH:MM:SS YYYY where, ● ● ● ● ● ● ● Default DD = Day of the week MM= Month Date=Date YYYY = Year HH = hour MM=Minutes SS = Seconds Timestamp of the cumulative power consumption. cfgServerCumulativePowerClear (Write Only) Table 299.
PAGE 214
NOTE: The getconfig subcommand always shows eight cfgServerPowerSupply indexes, even if two power supplies are installed in the system or the system supports a maximum of two PSUs. For the uninstalled and unsupported units, all the objects in the cfgServerPowerSupply group displays a value of 0. The following sections provide information about the objects in the cfgServerPowerSupply group. cfgServerPowerSupplyIndex Table 301. Details of cfgServerPowerSupplyIndex Description Specifies index of the PSU.
PAGE 215
cfgServerPowerSupplyFwVer (Read Only) Table 305. Details of cfgServerPowerSupplyFwVer Description Displays the firmware version of the PSU, in the format x.xx.xxx. Legal Values A string up to 8 characters. Default Null cfgServerPowerSupplyCurrentDraw (Read Only) Table 306. Details of cfgServerPowerSupplyCurrentDraw Description Displays the instantaneous current consumption in 0.1 amps. Legal Values A string of up to 32 characters. Default 0 cfgServerPowerSupplyType Table 307.
PAGE 216
cfgIPv6Address1 (Read or Write) Table 309. Details of cfgIPv6Address1 Description Specifies iDRAC IPv6 address. Specifies CMC IPv6 address. Legal Values String representing a valid IPv6 entry. Default : cfgIPv6Gateway (Read or Write) Table 310. Details of cfgIPv6Gateway attribute Description iDRAC gateway IPv6 address. CMC gateway IPv6 address. NOTE: This property is used only if cfgIPv6AutoConfig is set to 0 (false). Legal Values Specifies string representing a valid IPv6 entry.
PAGE 217
Table 312. Details of cfgIPv6PrefixLength attribute (continued) 0–128 Default 64 cfgIPv6LinkLocalAddress (Read Only) Table 313. Details of cfgIPv6LinkLocalAddress Description The iDRAC IPv6 link local address. Legal Values Specifies a string representing a valid IPv6 entry. Default : cfgIPv6Address2 (Read Only) Table 314. Details of cfgIPv6Address2 Description The iDRAC IPv6-second address. Legal Values A string representing a valid IPv6 entry. Default : cfgIPv6Address3 (Read Only) Table 315.
PAGE 218
Table 317. Details of cfgIPv6Address5 (continued) Default : cfgIPv6Address6 (Read Only) Table 318. Details of cfgIPv6Address6 Description The iDRAC IPv6 sixth address. Legal Values String representing a valid IPv6 entry. Default : cfgIPv6Address7 (Read Only) Table 319. Details of cfgIPv6Address7 Description The iDRAC IPv6 seventh address. Legal Values String representing a valid IPv6 entry. Default : cfgIPv6Address8 (Read Only) Table 320.
PAGE 219
cfgIPv6Address11 (Read Only) Table 323. Details of cfgIPv6Address11 Description The iDRAC IPv6 eleventh address. Legal Values String representing a valid IPv6 entry. Default : cfgIPv6Address12 (Read Only) Table 324. Details of cfgIPv6Address12 Description The iDRAC IPv6 twelfth address. Legal Values String representing a valid IPv6 entry. Default : cfgIPv6Address13 (Read Only) Table 325. Details of cfgIPv6Address13 Description The iDRAC IPv6 thirteenth address.
PAGE 220
cfgIPv6DNSServersFromDHCP6 (Read or Write) Table 328. Details of cfgIPv6DNSServersFromDHCP6 attribute Description Specifies whether cfgIPv6DNSServer1 and cfgIPv6DNSServer2 are static or DHCP IPv6 addresses. NOTE: This property is used only if cfgIPv6AutoConfig is set to 1(true). Legal Values 1 (TRUE) 0 (FALSE) Default 0 1 cfgIPv6DNSServer1 (Read or Write) Table 329. Details of cfgIPv6DNSServer1 attribute Description Specifies the IPv6 DNS server address.
PAGE 221
Table 331. Details of cfgIPv6StaticAddress1 (continued) Legal Values Any IPv6 address Default cfgIPv6StaticGateway (Read or Write) Table 332. Details of cfgIPv6StaticGateway Description Returns or sets gateway static IPv6 address. Legal Values Any IPv6 address Default cfgIPv6StaticPrefixLength (Read or Write) Table 333. Details of cfgIPv6StaticPrefixLength Description The prefix length for static IPv6 address 1. Legal Values 0–128 Default 64 cfgIPv6StaticAutoConfig (Read/Write) Table 334.
PAGE 222
cfgIPv6StaticDNSServer1 (Read or Write) Table 336. Details of cfgIPv6StaticDNSServer1 Description Specifies the DNS server 1 static IPv6 address. Legal Values Any IPv6 Address Default cfgIPv6StaticDNSServer2 (Read or Write) Table 337. Details of cfgIPv6StaticDNSServer2 Description Specifies the DNS server 2 static IPv6 address. Legal Values Any IPv6 address Default cfgIPv6DNSServer2 (Read or Write) Table 338.
PAGE 223
● ● ● ● cfgIPv6DNSServer1 cfgIPv6DNSServer2 cfgDNSServer1 cfgDNSServer2 cfgIPv6URL This group specifies properties used to configure iDRAC IPv6 URL. The following sections provide information about the objects in the cfgIPv6URL group. cfgIPv6URLstring (Read Only) Table 339. Details of cfgIPv6URLstring Description The iDRAC IPv6 URL. Legal Values A string of up to 80 characters. Default cfgIpmiSerial This group specifies properties used to configure the IPMI serial interface of the BMC.
PAGE 224
cfgIpmiSerialConnectionMode (Read or Write) Table 342. Details of cfgIpmiSerialConnectionMode Description When the iDRAC cfgSerialConsoleEnable property is set to 0(disabled), the iDRAC serial port becomes the IPMI serial port. This property determines the IPMI defined mode of the serial port. In Basic mode, the port uses binary data with the intent of communicating with an application program on the serial client.
PAGE 225
Table 346. Details of cfgIpmiSerialHandshakeControl (continued) ● 1 (TRUE) Default 1 cfgIpmiSerialNewLineSequence (Read or Write) Table 347. Details of cfgIpmiSerialNewLineSequence Description Specifies the new line sequence specification for the IPMI serial interface. Legal Values ● ● ● ● ● ● Default 1 0 1 2 3 4 5 — None — CR-LF — NULL — CR — LF-CR — LF cfgIpmiSerialLineEdit (Read or Write) Table 348.
PAGE 226
Table 350. Details of cfgSmartCardLogonEnable (continued) NOTE: Enabling with remote RACADM is only applicable for iDRAC on Rack and Tower Servers. Legal Values ● 0 (Disabled) ● 1 (Enabled) ● 2 (Enabled with Remote RACADM) — It is not applicable for iDRAC Enterprise on Blade Servers. Default 0 cfgSmartCardCRLEnable (Read or Write) Table 351. Details of cfgSmartCardCRLEnable Description Enables or disables the Certificate Revocation List (CRL).
PAGE 227
cfgNetTuningNic100MB (Read or Write) Table 353. Details of cfgNetTuningNic100MB Description Specifies the speed for iDRAC NIC. NOTE: To set this property: ● iDRAC NIC selection must be set to Dedicated mode. ● iDRAC NIC Auto negotiation must be disabled. ● iDRAC IPv4 must be enabled. ● iDRAC IPv4 DHCP must be enabled. ● iDRAC IPv6 must be enabled. ● iDRAC IPv6 auto configuration must be enabled.
PAGE 228
cfgSensorRedundancyIndex (Read Only) Table 356. Details of cfgSensorRedundancyIndex Description Specifies index for the sensor redundancy group being read. Only power supply redundancy is supported. Legal Values 1 Default None cfgSensorRedundancyPolicy (Read or Write) Table 357. Details of cfgSensorRedundancyPolicy Description Sets the power supply redundancy policy. Legal Values ● ● ● ● ● Default Any legal value at that particular execution instance.
PAGE 229
cfgVFlashSD This group is used to configure the properties for the Virtual Flash SD card. NOTE: If the vFlash card is present but is not enabled, the query for any property under this group displays: ERROR: vFlash is not enabled. To view the properties of this group, enable the vFlash using the command: racadm config -g cfgvFlashSD -o cfgvFlashSDEnable 1 The following sections provide information about the objects in the cfgVFlashSD group. cfgVFlashSDInitialized (Read Only) Table 360.
PAGE 230
Table 363. Details of cfgVFlashSDLicensed (continued) Legal Values ● 0(SD card is inserted) ● 1(vFlash SD card is inserted) Default None cfgVFlashSDAvailableSize (Read Only) Table 364. Details of cfgVFlashSDAvailableSize Description Displays the available memory (in MB) on the vFlash SD card that can be used to create new partitions. Legal Values A string of up to 64 characters. Default If the card is not initialized, default is 0. If initialized, displays the unused memory on the card.
PAGE 231
cfgVFlashPartitionIndex (Read Only) Table 367. Details of cfgVFlashPartitionIndex Description The index value of the partition. Legal Values Integer 1–16 Default None cfgVFlashPartitionSize (Read Only) Table 368. Details of cfgVFlashPartitionSize Description Displays the size of the partition. Legal Values 1 MB to 4 GB Default None cfgVFlashPartitionEmulationType (Read or Write) Table 369.
PAGE 232
Table 371. Details of cfgVFlashPartitionFormatType (continued) ● EXT3 ● CD ● RAW Default None cfgVFlashPartitionAccessType (Read or Write) Table 372. Details of cfgVFlashPartitionAccessType Description Indicates the partition access permissions. It configures the access type to read-write. Legal Values ● 0 (Read Only) ● 1 (Read-Write) Default 0 cfgVFlashPartitionAttachState (Read or Write) Table 373.
PAGE 233
For more information about generating certificate signing requests, see the subcommand sslcsrgen. For the country code, go to the link http://www.iso.org/iso/country_codes/iso_3166_code_lists.htm The following sections provide information about the objects in the cfgRacSecurity group. cfgRacSecCsrCommonName (Read or Write) Table 375. Details of cfgRacSecCsrCommonName attribute Description Specifies the CSR Common Name (CN) that must be an IP or iDRACCMC name as given in the certificate.
PAGE 234
cfgRacSecCsrCountryCode (Read/Write) Table 380. Details of cfgRacSecCsrCountryCode attribute Description Specifies the CSR Country Code (CC). Legal Values A string of 2 alphabet country code. Default US cfgRacSecCsrEmailAddr (Read or Write) Table 381. Details of cfgRacSecCsrEmailAddr attribute Description Specifies the CSR email address. Legal Values A string of up to 64 characters.
PAGE 235
4 Database Objects With Get and Set Commands This chapter provides the database groups and objects that must be used with the get or set subcommands. When using the objects, they must begin with FQDD or FQDD alias. The set operations for iDRAC, Lifecycle Controller and system objects do not require server restart. However, the set operations for NIC and BIOS objects are staged and job creation and server restart is required to apply and commit the pending values.
PAGE 236
Required License Dependency -- RACADM -- None BootRetryCnt -- Specify the number of retries to attempt in case of boot failure. Usage -- NoRetry - 0;1Retry - 1; 2Retries - 2;3Retries 3;4Retries - 4; 5Retries - 5;6Retries- 6; IndefiniteRetries, Default - NoRetry Required License -- RACADM Dependency -- None BootStrapType operating system.
PAGE 237
Example: /tmp # racadm help NIC.NICConfig.WakeOnLanLnkSpeed WakeOnLanLnkSpeed -- Select the port speed used for Wake on LAN mode Usage -- AutoNeg; 10Mbps Half; 10Mbps Full; 100Mbps Half; 100Mbps Full Required License -- RACADM Dependency -- None/tmp # ● The get and set commands for BIOS and NIC provide the list of attributes on the basis of the system configuration, BIOS version used, hardware, and so on.
PAGE 238
• • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • 238 iDRAC.Serial iDRAC.SerialRedirection iDRAC.serverboot iDRAC.ServiceModule iDRAC.SmartCard iDRAC.SNMP iDRAC.SNMP.Alert iDRAC.SSH iDRAC.SupportAssist iDRAC.SysLog iDRAC.Telnet iDRAC.Time iDRAC.Tuning iDRAC.Update iDRAC.USB iDRAC.UserDomain iDRAC.Users iDRAC.vflashpartition iDRAC.vflashsd iDRAC.VirtualConsole iDRAC.VirtualMedia iDRAC.VNCServer iDRAC.WebServer BIOS.BiosBootSettings BIOS.
PAGE 239
• • • • • • • • • NIC.IscsiSecondTgtParams NIC.NICConfig NIC.NICPartitioningConfig NIC.VndrConfigGroup NIC.VndrConfigPage Storage.Controller Storage.enclosure Storage.PhysicalDisk Storage.VirtualDisk System.Backplane The objects in this group manage the backplane. System.Backplane.BackplaneBusMode (Read Only) Table 383. Details of System.Backplane.BackplaneBusMode Description Indicates the backplane Serial General Purpose Input or Output (SGPIO) mode.
PAGE 240
System.ChassisInfo The objects in this group are applicable only to modular chassis such as Dell PowerEdge M1000e and Dell PowerEdge FX2. To obtain the chassis-specific information, use this group. System.ChassisInfo.Model (Read Only) Table 385. Details of System.ChassisInfo.Model Description Indicates the LCD string the user modifies. Legal Values String of up to 62 ASCII characters Default Value None Write privilege Not Applicable License Required Not Applicable Dependency None System.
PAGE 241
System.OpenIDConnectServer.ClientToken (Read or Write) Table 388. Details of System.OpenIDConnectServer.ClientToken attribute Description Indicates the Client Token. Legal Values String of up to 1024 ASCII characters Default Value Not Applicable Write Privilege Not Applicable License Required RACADM Dependency None System.OpenIDConnectServer.ClientURI (Read or Write) Table 389. Details ofSystem.OpenIDConnectServer.ClientURI attribute Description Indicates the Client URI.
PAGE 242
Table 391. Details of System.OpenIDConnectServer.Enabled attribute (continued) Dependency None System.OpenIDConnectServer.HttpsCertificate (Read or Write) Table 392. Details of System.OpenIDConnectServer.HttpsCertificate attribute Description Displays the HTTPS public certificate. Legal Values String of up to 2816 ASCII characters Default Value Not Applicable Write Privilege Not Applicable License Required RACADM Dependency None System.OpenIDConnectServer.
PAGE 243
Table 395. Details of System.OpenIDConnectServer.Name attribute (continued) Write Privilege Not Applicable License Required RACADM Dependency None System.QuickSync The objects in this group manage the configuration and recovery of QuickSync settings. System.QuickSync.Access (Read or Write) Table 396. Details of System.QuickSync.Access Description Configures the accessibility using Quick Sync on the server.
PAGE 244
Table 398. Details of System.QuickSync.InactivityTimerEnable (continued) Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Dependency To configure, the System.QuickSync.Presence property must indicate Present System.QuickSync.Presence (Read or Write) Table 399. Details of System.QuickSync.Presence Description Indicates the presence of Quick Sync feature in the server.
PAGE 245
Table 400. Details of System.LCD.Configuration (continued) Write Privilege Configure iDRAC and Configure User License Required iDRAC Express or iDRAC Enterprise Dependency None System.LCD.vConsoleIndication (Read or Write) Table 401. Details of System.LCD.vConsoleIndication Description Specifies the virtual console indication.
PAGE 246
System.LCD.LCDUserString (Read or Write) Table 404. Details of System.LCD.LCDUserString Description Indicates the LCD string set. NOTE: This property is deprecated from version 2.00.00.00. Use the System.LCD.UserDefinedString to perform the operation. Legal Values String of up to 62 ASCII characters Default Value 0 Write Privilege Not Applicable License Required Not Applicable Dependency Not Applicable System.LCD.QualifierTemp (Read or Write) Table 405. Details of System.LCD.
PAGE 247
Table 407. Details of System.LCD.UserDefinedString ( (continued) Write Privilege Not Applicable License Required Not Applicable Dependency Cannot be configured unless LCD Configuration is user defined. System.Location This group enables you to manage the server's physical location characteristics. The following section provides information about the objects in the.Location group. System.Location.Aisle (Read or Write) Table 408. Details of System.Location.
PAGE 248
Table 410. Details of System.Location.DeviceSize (continued) Write Privilege Not Applicable License Required iDRAC Express or iDRAC Enterprise Dependency None System.Location.Rack.Name (Read or Write) Table 411. Details of System.Location.Rack.Name Description Indicates rack where the system is located. Legal Values String of up to 128 ASCII characters Default Value Not Applicable Write Privilege Configure iDRAC License Required iDRAC Express or iDRAC Enterprise Dependency None System.
PAGE 249
System.Location.Chassis.Name (Read Only) Table 414. Details of System.Location.Chassis.Name Description Indicates the chassis name. Legal Values String of up to 128 ASCII characters Default Value Not Applicable Write Privilege Not Applicable License Required iDRAC Express or iDRAC Enterprise Dependency None System.Location.Chassis.Slot (Read or Write) Table 415. Details of System.Location.Chassis.Slot Description Indicates chassis slot.
PAGE 250
NOTE: For Dell PowerEdge FM120x4 server with more than one iDRAC, the power is received and shared from CMC. Hence, the information about power and temperature for individual iDRACs are not displayed. System.Power.Status (Read Only) Table 417. Details of System.Power.Status Description Represents the device power state, either ON or OFF. Legal Values ● 0 — Server is off ● 1 — Server is on.
PAGE 251
System.Power.Avg.LastHour (Read Only) Table 420. Details of System.Power.Avg.LastHour Description Displays the average power value during the last hour. Legal Values Values: 1–65535 Default Value Average power value during the last hour. Write Privilege Not Applicable License Required iDRAC Express or iDRAC Enterprise Dependency None System.Power.Avg.LastWeek (Read Only) Table 421. Details of System.Power.Avg.LastWeek Description Indicates the average power value during the last week.
PAGE 252
Table 423. Details of System.Power.Cap.ActivePolicy.Name (continued) Write Privilege Not Applicable License Required iDRAC Express or iDRAC Enterprise Dependency None System.Power.Cap.ActivePolicy.Watts (Read Only) Table 424. Details of System.Power.Cap.ActivePolicy.Watts Description Displays the Active Power Capacity in Watts Legal Values Values: 1–65535 Default Value Not Applicable Write Privilege Not Applicable License Required iDRAC Express or iDRAC Enterprise Dependency None System.
PAGE 253
Table 426. Details of System.Power.Cap. Enable (continued) License Required iDRAC Express or iDRAC Enterprise Dependency None System.Power.Cap.MaxThreshold (Read Only) Table 427. Details of System.Power.Cap.MaxThreshold Description Because it is based on the current component inventory, it has maximum server power capacity. Legal Values Values: 1–65535 Default Value Not Applicable Write Privilege Not Applicable License Required iDRAC Express or iDRAC Enterprise Dependency None System.Power.
PAGE 254
Table 429. Details of System.Power.Cap.Percent (continued) Dependency Enable System.Power.Cap.Enable System.Power.Redundancypolicy (Read or Write) Table 430. Details of System.Power.Redundancypolicy Description Selects the redundancy policy. Legal Values ● 255 — N/A, for the systems that are not supported ● 0 — Not Redundant — In this mode, even if one PSU stops functioning, the server is automatically turned off.
PAGE 255
Table 432. Details of System.Power.EnergyConsumption (continued) Default Value Cumulative power consumption Write Privilege Configure iDRAC License Required iDRAC Express or iDRAC Enterprise Dependency None System.Power.EnergyConsumption.Clear (Read or Write) Table 433. Details of System.Power.EnergyConsumption.Clear Description Clears the cumulative power consumption timestamps.
PAGE 256
Table 435. Details of System.Power.Hotspare.Enable (continued) License Required iDRAC Express or iDRAC Enterprise Dependency None System.Power.Hotspare.PrimaryPSU (Read or Write) Table 436. Details of System.Power.Hotspare.PrimaryPSU Description Represents the primary PSU selection. NOTE: This object is supported only for iDRAC on Rack and Tower servers.
PAGE 257
Table 438. Details of System.Power.Max.Amps.TimeStamp (continued) Dependency None System.Power.Max.Headroom (Read Only) Table 439. Details of System.Power.Max.Headroom Description Displays the difference between the available power and the peak power consumption. NOTE: This object is not applicable on iDRAC on Modular servers. Legal Values Values: 1–65535 Default Value Difference between the available power and the peak power consumption.
PAGE 258
System.Power.Max.LastHour (Read Only) Table 442. Details of System.Power.Max.LastHour Description Displays the maximum power value during the last hour. Legal Values Values: 1–65535 Default Value Maximum power value during the last hour. Write Privilege Not Applicable License Required iDRAC Express or iDRAC Enterprise Dependency None System.Power.Max.LastHour.TimeStamp (Read Only) Table 443. Details of System.Power.Max.LastHour.
PAGE 259
Table 445. Details of System.Power.Max.LastWeek.TimeStamp (continued) Default Value Timestamp of the maximum power value during the last week. Write Privilege Not Applicable License Required iDRAC Express or iDRAC Enterprise Dependency None System.Power.Max. Power (Read Only) Table 446. Details of System.Power.Max. Power Description The server consumes maximum power, because the last value was cleared. Legal Values Values: 1–65535 Default Value Peak power consumption of the server.
PAGE 260
Table 448. Details of System.Power.Max.PowerClear (continued) Dependency None System.Power.Min.LastDay (Read Only) Table 449. Details of System.Power.Min.LastDay Description Displays the minimum power during the last day. Legal Values Values: 1–65535 Default Value Minimum power value during the last day. Write Privilege Not Applicable License Required iDRAC Express or iDRAC Enterprise Dependency None System.Power.Min.LastDay.TimeStamp (Read Only) Table 450. Details of System.Power.Min.LastDay.
PAGE 261
System.Power.Min.LastHour.Timestamp (Read Only) Table 452. Details of System.Power.Min.LastHour.Timestamp Description Indicates the timestamp of minimum power during the last hour. Legal Values String of up to 254 ASCII characters Default Value Timestamp of the minimum power value during the last hour. Write Privilege Not Applicable License Required iDRAC Express or iDRAC Enterprise Dependency None System.Power.Min.LastWeek (Read Only) Table 453. Details of System.Power.Min.
PAGE 262
Table 455. Details of System.Power.PCIeAllocation (continued) Legal Values ● 0 — Disabled ● 1 — Enabled Default Value ● 0 — For platforms that do not support PCIe cards. ● 500 W — For platforms that support PCIe cards. Write Privilege Configure iDRAC License Required iDRAC Express or iDRAC Enterprise Dependency None System.Power.PFCEnable (Read or Write) Table 456. Details of System.Power.PFCEnable Description Enables the power factor correction enable.
PAGE 263
Table 457. Details of System.Power.RedundancyCapabilities (continued) License Required Not Applicable Dependency Not Applicable System.Power.RedundantState (Read Only) Table 458. Details of System.Power.RedundantState Description Retrieves the redundancy state for the chassis. NOTE: This object is not applicable for Rack and Tower server. Legal Values ● 0 — None ● 1 — Full Default 0 — None Write Privilege Not Applicable License Required Not Applicable Dependency Not Applicable System.Power.
PAGE 264
System.Power.Realtime.Power (Read Only) Table 461. Details of System.Power.Realtime.Power Description Displays the power consumed by the server Legal Values Integral values: 1-65535 Default Value 0 — Server is off Write Privilege Not Applicable License Required iDRAC Express or iDRAC Enterprise Dependency Not Applicable System.Power.Supply This group provides information relating to the Power Supplies. This group is indexed from 1 to 4.
PAGE 265
System.Power.Supply.[i].MaxInputPower (Read Only) Table 464. Details of System.Power.Supply.[i].MaxInputPower Description Displays the AC input rated power in Watts. Legal Values Integer > 0 Default Value 0 Write Privilege Not Applicable License Required Not Applicable Dependency Not Applicable System.Power.Supply.[i].MaxOutputPower (Read Only) Table 465. Details of System.Power.Supply.[i].MaxOutputPower Description Displays the DC output rated power in Watts.
PAGE 266
Table 467. Details of System.Power.Supply.[i].Type (continued) Legal Values String upto 32 characters. Default None Write Privilege Not Applicable License Required Not Applicable Dependency Not Applicable System.Power.Supply.[i].LineStatus (Read Only) Table 468. Details of System.Power.Supply.[i].LineStatus Description Specifies if this power supply is powered off or on.
PAGE 267
Table 470. Details of System.ServerOS.HostName (continued) Default Value Not Applicable Write Privilege Configure iDRAC License Required iDRAC Express or iDRAC Enterprise Dependency None System.ServerOS.OSName (Read or Write) Table 471. Details of System.ServerOS.OSName Description Displays the operating system name of the managed server.
PAGE 268
System.ThermalSettings This group provides information about the thermal settings of the server. To know more about the platforms supported for AirExhaustTemp and FanSpeedOffset settings, see the iDRAC User's Guide available at www.dell.com/esmmanuals. System.ThermalSettings.AirExhaustTemp (Read or Write) Table 474. Details of System.ThermalSettings.AirExhaustTemp Description Displays the air exhaust temperature and sets the exhaust temperature to any appropriate value.
PAGE 269
Table 476. Details of System.ThermalSettings.MinimumFanSpeed (continued) License Required iDRAC Express or iDRAC Enterprise Dependency None System.ThermalSettings.FanSpeedOffset (Read or Write) Table 477. Details of System.ThermalSettings.FanSpeedOffset Description Specifies the fan speed offset. NOTE: This attribute is platform dependent.
PAGE 270
System.ThermalSettings.FanSpeedHighOffsetVal (Read Only) Table 480. Details of System.ThermalSettings.FanSpeedHighOffsetVal Description Indicates the percentage range for the high fan offset speed. NOTE: This attribute is platform dependent. Legal Values Integral Values: 0 – 100 Default Value 0 License Required iDRAC Express or iDRAC Enterprise Dependency None System.ThermalSettings.FanSpeedMaxOffsetVal (Read Only) Table 481. Details of System.ThermalSettings.
PAGE 271
Table 483. Details of System.ThermalSettings.MFSMaximumLimit (continued) License Required iDRAC Express or iDRAC Enterprise Dependency None System.ThermalSettings.ThermalProfile (Read or Write) Table 484. Details of System.ThermalSettings.ThermalProfile Description Sets the thermal base algorithm. NOTE: Restart the system to activate the power and thermal settings.
PAGE 272
Table 486. Details of System.ThermalConfig.CriticalEventGenerationInterval (continued) Legal Values Integral Values: 0-365 Default Value 30 Write Privilege Configure iDRAC License Required iDRAC Express or iDRAC Enterprise Dependency None System.ThermalConfig.EventGenerationInterval (Read or Write) Table 487. Details of System.ThermalConfig.EventGenerationInterval Description Indicates the time interval (in days) for warning events to be generated.
PAGE 273
Table 489. Details of LifecycleController.LCAttributes.autobackup (continued) Legal Values ● 0 — Disabled ● 1 — Enabled Default Value 0 — Disabled Write Privilege Server Control License Required iDRAC Enterprise Dependency None LifecycleController.LCAttributes.AutoDiscovery (Read Only) Table 490. Details of LifecycleController.LCAttributes.AutoDiscovery Description Enables or disables the auto discovery scheduler.
PAGE 274
Table 492. Details of LifecycleController.LCAttributes.BiosRTDRequested (continued) License Required iDRAC Express or iDRAC Enterprise Dependency None LifecycleController.LCAttributes.CollectSystemInventoryOnRestar t (Read or Write) Table 493. Details of LifecycleController.LCAttributes.CollectSystemInventoryOnRestart Description Enables or disables collection of system inventory on host reboot.
PAGE 275
LifecycleController.LCAttributes.IPChangeNotifyPS (Read or Write) Table 496. Details of LifecycleController.LCAttributes.IPChangeNotifyPS Description Notifies the provisioning server about the change in IP address. Legal Values ● 0 — Off ● 1 — On Default Value 0 — Off Write Privilege Configure iDRAC License Required iDRAC Enterprise Dependency None LifecycleController.LCAttributes.Licensed (Read Only) Table 497. Details of LifecycleController.LCAttributes.
PAGE 276
LifecycleController.LCAttributes.ProvisioningServer (Read or Write) Table 499. Details of LifecycleController.LCAttributes.ProvisioningServer Description Specifies the Provisioning Server Address. Legal Values String of up to 255 ACSII characters Default Value Not Applicable Write Privilege Configure iDRAC License Required iDRAC Enterprise Dependency None LifecycleController.LCAttributes.PartConfigurationUpdate (Read or Write) Table 500. Details of LifecycleController.LCAttributes.
PAGE 277
LifecycleController.LCAttributes.SystemID (Read Only) Table 502. Details of LifecycleController.LCAttributes.SystemID Description Specifies the Dell System ID. Legal Values Not Applicable Default Value None Write Privilege Not Applicable License Required iDRAC Enterprise Dependency None LifecycleController.LCAttributes.UserProxyName (Read and Write) Table 503. Details of LifecycleController.LCAttributes.UserProxyName Description Enables to set user proxy name if the default is not set.
PAGE 278
LifecycleController.LCAttributes.UserProxyServer (Read and Write) Table 506. Details of LifecycleController.LCAttributes.UserProxyServer Description Enables to set user proxy server if the default is not set. Legal Values String of up to 64 ASCII characters Default Value None License Required iDRAC Enterprise Dependency None LifecycleController.LCAttributes.UserProxyType (Read and Write) Table 507. Details of LifecycleController.LCAttributes.
PAGE 279
iDRAC.ActiveDirectory To manage the configuration of the iDRAC Active Directory features, use the objects in this group. iDRAC.ActiveDirectory.AuthTimeout (Read or Write) Table 509. Details of iDRAC.ActiveDirectory.AuthTimeout Description To wait for ActiveDirectory authentication requests to complete before timing out, specify the time in seconds.
PAGE 280
Table 511. Details of iDRAC.ActiveDirectory.DCLookupByUserDomain (continued) Dependency Cannot be disabled unless the DC Lookup Domain Name is set. iDRAC.ActiveDirectory.DCLookupDomainName (Read or Write) Table 512. Details of iDRAC.ActiveDirectory.DCLookupDomainName Description The configured search domain is used when DCLookupByUserDomain is disabled.
PAGE 281
Table 514. Details of iDRAC.ActiveDirectory.DomainController1 (continued) Dependency None iDRAC.ActiveDirectory.DomainController2 (Read or Write) Table 515. Details of iDRAC.ActiveDirectory.DomainController2 Description FQDN that stores the address of the active directory domain controller 2 Legal Values String of up to 254 ASCII characters Default Value Not Applicable Write Privilege Configure iDRAC and configure user License Required iDRAC Enterprise Dependency None iDRAC.ActiveDirectory.
PAGE 282
iDRAC.ActiveDirectory.GCLookupEnable (Read or Write) Table 518. Details of iDRAC.ActiveDirectory.GCLookupEnable Description Determines how to look up the global catalog server. Legal Values ● 0 — Disabled ● 1 — Enabled Default Value 0 — Disabled Write Privilege Configure iDRAC and configure user License Required iDRAC Enterprise Dependency Cannot be enabled unless one of the following is configured: ● IPv4.DNS1 ● IPv4.DNS2 ● IPv6.DNS1 ● IPv6.DNS2 iDRAC.ActiveDirectory.
PAGE 283
iDRAC.ActiveDirectory.GlobalCatalog2 (Read or Write) Table 521. Details of iDRAC.ActiveDirectory.GlobalCatalog2 Description To obtain user names, specifies the Global Catalog server from which you want the iDRAC. Legal Values String of up to 254 ASCII characters Default Value Not Applicable Write Privilege Configure iDRAC and configure user License Required iDRAC Enterprise Dependency None iDRAC.ActiveDirectory.GlobalCatalog3 (Read or Write) Table 522. Details of iDRAC.ActiveDirectory.
PAGE 284
Table 524. Details of iDRAC.ActiveDirectory.RacName (continued) Default Value Not Applicable Write Privilege Configure iDRAC and configure user License Required iDRAC Enterprise Dependency None iDRAC.ActiveDirectory.Schema (Read or Write) Table 525. Details of iDRAC.ActiveDirectory.Schema Description To use with Active Directory, determine the schema type.
PAGE 285
Table 527. Details of iDRAC.ADGroup.Domain (continued) Legal Values String of up to 254 ASCII characters Default Value Not Applicable Write Privilege Configure iDRAC and configure user License Required iDRAC Enterprise Dependency None iDRAC.ADGroup.Name (Read or Write) Table 528. Details of iDRAC.ADGroup.Name Description Name of the Role Group as recorded in the Active Directory forest.
PAGE 286
Default Value 1 Write Privilege Configure iDRAC License Required iDRAC Basic Dependancy None iDRAC.AutoOSLock To manage the OS Auto lock feature, use these objects in this group. iDRAC.AutoOSLock.AutoOSLockState (Read or Write) Table 530. Details of iDRAC.AutoOSLock.AutoOSLockState Description Enable or Disable OS Auto lock feature.
PAGE 287
Table 532. Details of iDRAC.EmailAlert.CustomMsg (continued) Legal Values A string of up to 32 ASCII characters Default Value Not Applicable Write Privilege Configure iDRAC License Required iDRAC Express or iDRAC Enterprise Dependency None iDRAC.EmailAlert.Enable (Read or Write) Table 533. Details of iDRAC.EmailAlert.Enable Description To receive alerts, enable or disable the destination.
PAGE 288
iDRAC.Info.Build (Read or Write) Table 534. Details of iDRAC.Info.Build Description String containing the current product build version. Legal Values String of up to 16 ASCII characters Default Value Not Applicable Write Privilege Configure iDRAC License Required iDRAC Express or iDRAC Enterprise Dependency None iDRAC.Info.Description (Read or Write) Table 535. Details of iDRAC.Info.Description Description Text description of the iDRAC.
PAGE 289
Table 537. Details of iDRAC.Info.Product (continued) Write Privilege Configure iDRAC License Required iDRAC Express or iDRAC Enterprise Dependency None iDRAC.Info.Type (Read or Write) Table 538. Details of iDRAC.Info.Type Description Identifies the remote access controller type Legal Values ● 16 (12G iDRAC Monolithic) ● 17 (12G iDRAC Modular) Default Vlaue 12G Monolithic Write Privilege Configure iDRAC License Required iDRAC Express or iDRAC Enterprise Dependency None iDRAC.Info.
PAGE 290
iDRAC.IOIDOpt The objects in this group manage the IOIDOpt attributes. iDRAC.IOIDOpt.IOIDOptEnable (Read or Write) Description Enable IO Identity Optimization Legal Values ● Disabled-0 ● Enabled-1 Default Value 0 Write Privilege Configure iDRAC License Required iDRAC Basic Dependancy None iDRAC.IOIDOptEnable (Read or Write) Table 541. Details of iDRAC.IOIDOptEnable Description Enables or disables Identity Optimization (IO).
PAGE 291
Table 542. Details of iDRAC.IOIDOpt.InitiatorPersistencePolicy (continued) License Required iDRAC Express or iDRAC Enterprise Dependency IOIDOptEnable attribute must be enabled. iDRAC.IOIDOpt.StorageTargetPersistencePolicy (Read or Write) Table 543. Details of iDRAC.IOIDOpt.StorageTargetPersistencePolicy Description Sets the Virtual Address Management StorageTargetPersistencePolicy.
PAGE 292
Table 544. Details of iDRAC.IOIDOpt.VirtualAddressPersistencePolicyAuxPwrd (continued) Dependency To configure, the iDRAC.IOIDOpt.Enable property must indicate Enabled. iDRAC.IOIDOpt.VirtualAddressPersistencePolicyNonAuxPwrd (Read or Write) Table 545. Details of iDRAC.IOIDOpt.VirtualAddressPersistencePolicyNonAuxPwrd Description Applied for the Non-Aux powered devices, which persist the virtual address on warm reset.
PAGE 293
iDRAC.IPBlocking.FailCount (Read or Write) Table 547. Details of iDRAC.IPBlocking.FailCount Description The maximum number of logins that are unsuccessful to occur within the window before logs in attempts from the IP address are rejected. Legal Values Integral values: 2–16 Write Privilege Configure iDRAC License Required iDRAC Express or iDRAC Enterprise Dependency None iDRAC.IPBlocking.FailWindow (Read or Write) Table 548. Details of iDRAC.IPBlocking.
PAGE 294
Table 550. Details of iDRAC.IPBlocking.RangeAddr (continued) Write Privilege Configure iDRAC License Required iDRAC Express or iDRAC Enterprise Dependency None iDRAC.IPBlocking.RangeEnable (Read or Write) Table 551. Details of iDRAC.IPBlocking.RangeEnable Description Enables or disables the IPv4 Address Range validation feature of iDRAC.
PAGE 295
Table 553. Details of iDRAC.IPMILan.AlertEnable (continued) Default Value 0 — Disabled Write Privilege Configure iDRAC License Required iDRAC Express or iDRAC Enterprise Dependency None iDRAC.IPMILan.CommunityName (Read or Write) Table 554. Details of iDRAC.IPMILan.CommunityName Description Specifies the SNMP community name for traps.
PAGE 296
Table 556. Details of iDRAC.IPMILan.EncryptionKey (continued) License Required iDRAC Express or iDRAC Enterprise Dependency None iDRAC.IPMILan.PrivLimit (Read or Write) Table 557. Details of iDRAC.IPMILan.PrivLimit Description Specifies the maximum privilege level for IPMI over LAN access. Legal Values ● 2 — User ● 3 — Operator ● 4 — Administrator Default Value 4 — Administrator Write Privilege Configure iDRAC License Required iDRAC Express or iDRAC Enterprise Dependency None iDRAC.
PAGE 297
iDRAC.IPMISerial.ChanPrivLimit (Read or Write) Table 559. Details of iDRAC.IPMISerial.ChanPrivLimit Description Specifies the maximum privilege limit allowed on the IPMI serial channel. Legal Values ● 2 — User ● 3 — Operator ● 4 — Administrator Default Value 4 — Administrator Write Privilege Configure iDRAC License Required iDRAC Express or iDRAC Enterprise Dependency None iDRAC.IPMISerial.ConnectionMode (Read or Write) Table 560. Details of iDRAC.IPMISerial.
PAGE 298
iDRAC.IPMISerial.EchoControl (Read or Write) Table 562. Details of iDRAC.IPMISerial.EchoControl Description Enables or disables echo control on the IPMI serial interface. Legal Values ● 0 — Disabled ● 1 — Enabled Default Value 1 — Enabled Write Privilege Configure iDRAC License Required iDRAC Express or iDRAC Enterprise Dependency None iDRAC.IPMISerial.FlowControl (Read or Write) Table 563. Details of iDRAC.IPMISerial.
PAGE 299
iDRAC.IPMISerial.InputNewLineSeq (Read or Write) Table 565. Details of iDRAC.IPMISerial.InputNewLineSeq Description Specifies the input new line sequence for the IPMI serial interface. Legal Values ● 1 — Enter ● 2 — Null Default Value 2 — Null Write Privilege Configure iDRAC License Required iDRAC Express or iDRAC Enterprise Dependency None iDRAC.IPMISerial.LineEdit (Read or Write) Table 566. Details of iDRAC.IPMISerial.
PAGE 300
iDRAC.IPMISOL Use the objects in this group to configure the SOL capabilities of the system. iDRAC.IPMISOL.AccumulateInterval (Read or Write) Table 568. Details of iDRAC.IPMISOL.AccumulateInterval Description Specifies the typical amount of time that iDRAC waits before transmitting a partial SOL character data packet. Legal Values Integral values: 1–255 Default Value Not Applicable Write Privilege Configure iDRAC License Required iDRAC Express or iDRAC Enterprise Dependency None iDRAC.IPMISOL.
PAGE 301
Table 570. Details of iDRAC.IPMISOL.Enable (continued) Dependency None iDRAC.IPMISOL.MinPrivilege (Read or Write) Table 571. Details of iDRAC.IPMISOL.MinPrivilege Description Specifies the minimum privilege level required for serial access. Legal Values ● 2—User ● 3—Operator ● 4—Administrator Default Value 4—Administrator Write Privilege Configure iDRAC License Required iDRAC Express or iDRAC Enterprise Dependency None iDRAC.IPMISOL.SendThreshold (Read or Write) Table 572. Details of iDRAC.
PAGE 302
Table 573. Details of iDRAC.IPv4.Address (continued) Write Privilege Configure iDRAC License Required iDRAC Express or iDRAC Enterprise Dependency Cannot be set unless IPv4.DHCPEnable is disabled. iDRAC.IPv4.DHCPEnable (Read or Write) Table 574. Details of iDRAC.IPv4.DHCPEnable Description Specifies if DHCP is used to assign the iDRAC IPv4 address.
PAGE 303
Table 576. Details of iDRAC.IPv4.DNS2 (continued) Dependency Cannot be set unless IPv4.DNSFromDHCP is disabled. iDRAC.IPv4.DNSFromDHCP (Read or Write) Table 577. Details of iDRAC.IPv4.DNSFromDHCP Description Specifies if the DNS server IPv4 addresses must be assigned from the DHCP server on the network. Legal Values ● 0 — Disabled ● 1 — Enabled Default Value 0 — Disabled Write Privilege Configure iDRAC License Required iDRAC Express or iDRAC Enterprise Dependency Cannot be enabled unless IPv4.
PAGE 304
iDRAC.IPv4.Netmask (Read or Write) Table 580. Details of iDRAC.IPv4.Netmask Description The subnet mask used for the iDRAC IPv4 address. Legal Values Valid IPv4 netmask Default Value 255.255.255.0 Write Privilege Configure iDRAC License Required iDRAC Express or iDRAC Enterprise Dependency Cannot be set unless IPv4.DHCPEnable is disabled. iDRAC.IPv4Static Use the objects in this group to manage the IPv4 Static configuration properties of iDRAC. iDRAC.IPv4Static.
PAGE 305
iDRAC.IPv4Static.DNS2 (Read or Write) Table 583. Details of iDRAC.IPv4Static.DNS2 Description Statically configurable DNS Server 2. Legal Values Valid IPv4 Address Default Value 0.0.0.0 Write Privilege Configure iDRAC License Required iDRAC Express or iDRAC Enterprise Dependency None iDRAC.IPv4Static.DNSFromDHCP (Read or Write) Table 584. Details of iDRAC.IPv4Static.DNSFromDHCP Description Specifies if the DNS server IPv4 addresses should be assigned from the DHCP server on the network.
PAGE 306
Table 586. Details of iDRAC.IPv4Static.Netmask (continued) Legal Values Valid IPv4 netmask Default Value 255.255.255.0 Write Privilege Configure iDRAC License Required iDRAC Express or iDRAC Enterprise Dependency None iDRAC.IPv6 To manage the IPv6 configuration properties of iDRAC, use the objects in this group. iDRAC.IPv6.Address1 (Read or Write) Table 587. Details of iDRAC.IPv6.Address 1 attribute Description iDRAC IPv6 Address.
PAGE 307
Table 589. Details of iDRAC.IPv6.Address 3 attribute (continued) Legal Values Valid IPv6 Address Default Value Write Privilege Configure iDRAC License Required iDRAC Express or iDRAC Enterprise Dependency None iDRAC.IPv6.Address4 (Read or Write) Table 590. Details of iDRAC.IPv6.Address 4 attribute Description iDRAC IPv6 fourth address. Legal Values Valid IPv6 Address Default Value Write Privilege Configure iDRAC License Required iDRAC Express or iDRAC Enterprise Dependency None iDRAC.IPv6.
PAGE 308
Table 592. Details of iDRAC.IPv6.Address 6 attribute (continued) License Required iDRAC Express or iDRAC Enterprise Dependency None iDRAC.IPv6.Address7 (Read or Write) Table 593. Details of iDRAC.IPv6.Address 7 attribute Description iDRAC IPv6 seventh address. Legal Values Valid IPv6 Address Default Value Write Privilege Configure iDRAC License Required iDRAC Express or iDRAC Enterprise Dependency None iDRAC.IPv6.Address8 (Read or Write) Table 594. Details of iDRAC.IPv6.
PAGE 309
iDRAC.IPv6.Address10 (Read or Write) Table 596. Details of iDRAC.IPv6.Address10 attribute Description iDRAC IPv6 tenth address. Legal Values Valid IPv6 Address Default Value :: Write Privilege Configure iDRAC License Required iDRAC Express or iDRAC Enterprise Dependency None iDRAC.IPv6.Address11 (Read or Write) Table 597. Details of iDRAC.IPv6.Address11 attribute Description iDRAC IPv6 eleventh address.
PAGE 310
Table 599. Details of iDRAC.IPv6.Address13 attribute (continued) Default Value Write Privilege Configure iDRAC License Required iDRAC Express or iDRAC Enterprise Dependency None iDRAC.IPv6.Address14 (Read or Write) Table 600. Details of iDRAC.IPv6.Address14 attribute Description iDRAC IPv6 fourteenth address. Legal Values Valid IPv6 Address Default Value :: Write Privilege Configure iDRAC License Required iDRAC Express or iDRAC Enterprise Dependency None iDRAC.IPv6.
PAGE 311
Table 602. Details of iDRAC.IPv6.AutoConfig attribute (continued) License Required iDRAC Express or iDRAC Enterprise Dependency None iDRAC.IPv6.DNS1 (Read or Write) Table 603. Details of iDRAC.IPv6.DNS1 attribute Description IPv6 DNS Server 1 Address. Legal Values Valid IPv6 Address Default Value :: Write Privilege Configure iDRAC License Required iDRAC Express or iDRAC Enterprise Dependency Cannot be set unless IPv6.DNSFromDHCP6 is disabled. iDRAC.IPv6.DNS2 (Read or Write) Table 604.
PAGE 312
iDRAC.IPv6.Enable (Read or Write) Table 606. Details of iDRAC.IPv6.Enable attribute Description Enables or Disables iDRAC IPv6 stack. Legal Values ● 0 — Disabled ● 1 — Enabled Default Value 0 — Disabled Write Privilege Configure iDRAC License Required iDRAC Express or iDRAC Enterprise Dependency None iDRAC.IPv6.Gateway (Read or Write) Table 607. Details of iDRAC.IPv6.
PAGE 313
Table 609. Details of iDRAC.IPv6.PrefixLength attribute (continued) Legal Values Integral values: 1–128 Default Value 64 Write Privilege Configure iDRAC License Required iDRAC Express or iDRAC Enterprise Dependency None iDRAC.IPv6Static To manage the IPv6 static configuration properties of iDRAC, use the objects in this group iDRAC.IPv6Static.Address1 (Read or Write) Table 610. Details of iDRAC.IPv6Static.Address1 attribute Description iDRAC static IPv6 address.
PAGE 314
Table 612. Details of iDRAC.IPv6Static.DNS2 attribute (continued) License Required iDRAC Express or iDRAC Enterprise Dependency None iDRAC.IPv6Static.DNSFromDHCP6 (Read or Write) Table 613. Details of iDRAC.IPv6Static.DNSFromDHCP6 attribute Description Specifies if the DNS server IPv6 addresses must be assigned from the DHCP server on the network.
PAGE 315
iDRAC.IPv6URL Use the objects in this group to manage the IPv6 static configuration properties of iDRAC. iDRAC.IPv6URL.URL (Read Only) Table 616. Details of iDRAC.IPv6URL.URL attribute Description iDRAC IPv6 URL String of format 'https://[ipv6 address]:' Legal Values IPv6 URL String Default Value Write Privilege Not Applicable License Required iDRAC Express or iDRAC Enterprise Dependency iDRAC IPv6 has to be Enabled iDRAC.
PAGE 316
iDRAC.LDAP.BindPassword (Write Only) Table 619. Details of iDRAC.LDAP.BindPassword attribute Description A bind password to use along with the bindDN. Legal Values String of up to 254 ASCII characters Default Value Not Applicable Write Privilege Configure iDRAC and configure user License Required iDRAC Enterprise Dependency None iDRAC.LDAP.CertValidationEnable (Read or Write) Table 620. Details of iDRAC.LDAP.
PAGE 317
Table 622. Details of iDRAC.LDAP.GroupAttribute attribute (continued) Legal Values String of up to 128 ASCII characters Default Value Not Applicable Write Privilege Configure iDRAC and configure user License Required iDRAC Enterprise Dependency None iDRAC.LDAP.GroupAttributeIsDN (Read or Write) Table 623. Details of iDRAC.LDAP.GroupAttributeIsDN attribute Description Specifies whether the user domain name must be used from the LDAP server or from the user that provides login.
PAGE 318
Table 625. Details of iDRAC.LDAP.SearchFilter attribute (continued) Default Value Not Applicable Write Privilege Configure iDRAC and configure user License Required iDRAC Enterprise Dependency None iDRAC.LDAP.Server (Read or Write) Table 626. Details of iDRAC.LDAP.Server attribute Description Configures the address of the LDAP Server.
PAGE 319
Table 628. Details of iDRAC.LDAPRoleGroup.DN attribute (continued) Write Privilege Configure iDRAC License Required iDRAC Enterprise Dependency None iDRAC.LDAPRoleGroup.Privilege(Read or Write) Table 629. Details of iiDRAC.LDAPRoleGroup.Privilege attribute Description A bit-mask defining the privileges associated with this particular group. Legal Values Integral values: 0–511 (0x1FF) Default Value 0 Write Privilege Configure iDRAC License Required iDRAC Enterprise Dependency None iDRAC.
PAGE 320
Table 631. Details of iDRAC.LocalSecurity.PrebootConfig attribute (continued) Default Value 0 — Disabled Write Privilege Configure iDRAC License Required iDRAC Express or iDRAC Enterprise Dependency None iDRAC.Logging iDRAC. Logging Manages the ability to configure iDRAC iDRAC.Logging.SELOEMEventFilterEnable (Read or Write) Table 632. Details of iDRAC.Logging.SELOEMEventFilterEnable attribute Description Enables or disables the ability of Logging SEL Records with OEM.
PAGE 321
Table 633. Details of iDRAC.NIC.Autoconfig attribute (continued) ● 1 — Enable Once NOTE: iDRAC performs DHCP configuration once. ● 2 — Enable Once After Reset NOTE: Configures after iDRAC reset. Default Values 0 — Disabled Write Privilege Configure iDRAC License Required iDRAC Enterprise Dependency None iDRAC.NIC.AutoDetect (Read or Write) Table 634. Details of iDRAC.NIC.AutoDetect attribute Description Enables or disables auto detection feature of iDRAC.
PAGE 322
iDRAC.NIC.DedicatedNICScanTime (Read or Write) Table 636. Details of iDRAC.NIC.DedicatedNICScanTime attribute Description Wait time for the iDRAC to switch from dedicated mode to shared mode. Legal Values Integral values: 5–255 Default Value 5 Write Privilege Configure iDRAC License Required iDRAC Express or iDRAC Enterprise Dependency None iDRAC.NIC.DNSDomainFromDHCP (Read or Write) Table 637. Details of iDRAC.NIC.
PAGE 323
iDRAC.NIC.DNSDomainNameFromDHCP (Read or Write) Table 639. Details of DRAC.NIC.DNSDomainNameFromDHCP attribute Description Specifies that the iDRAC DNS domain name must be assigned from the network DHCP server. Legal Values ● 0 — Disabled ● 1 — Enabled Default Value 0 — Disabled Write Privilege Configure iDRAC License Required iDRAC Express or iDRAC Enterprise Dependency None iDRAC.NIC.DNSRacName (Read or Write) Table 640. Details of iDRAC.NIC.DNSRacName attribute Description The iDRAC name.
PAGE 324
iDRAC.NIC.Duplex (Read or Write) Table 642. Details of iDRAC.NIC.Duplex attribute Description Specifies the duplex setting for the iDRAC NIC. Legal Values ● 0 — Half ● 1 — Full Default value 1 — Full Write Privilege Configure iDRAC License Required iDRAC Express or iDRAC Enterprise Dependency None iDRAC.NIC.Enable (Read or Write) Table 643. Details of iDRAC.NIC.Enable attribute Description Enables or Disables the iDRAC network interface controller.
PAGE 325
iDRAC.NIC.MACAddress (Read or Write) Table 645. Details of iDRAC.NIC.MACAddress attribute Description The MAC Address of the iDRAC. Legal Values String of up to 17 ASCII characters Default Value Not Applicable Write Privilege Configure iDRAC License Required iDRAC Express or iDRAC Enterprise Dependency None iDRAC.NIC.MTU (Read or Write) Table 646. Details of iDRAC.NIC.MTU attribute Description The size in bytes of the maximum transmission unit uses the iDRAC NIC.
PAGE 326
iDRAC.NIC.SharedNICScanTime (Read or Write) Table 648. Details of iDRAC.NIC.SharedNICScanTime attribute Description Wait time for the iDRAC to switch from shared mode to dedicated mode. Legal Values Integral values: 5–255 Default Value 30 Write Privilege Configure iDRAC License Required iDRAC Express or iDRAC Enterprise Dependency None iDRAC.NIC.Speed (Read or Write) Table 649. Details of iDRAC.NIC.Speed attribute Description Specifies the speed for iDRAC NIC.
PAGE 327
Table 650. Details of iDRAC.NIC.TopologyLldp attribute (continued) Dependency None iDRAC.NIC.VLanEnable (Read Only) Table 651. Details of iDRAC.NIC.VLanEnable attribute Description Enables or disables the VLAN capabilities of the iDRAC. NOTE: This object is applicable only to iDRAC on Racks and Towers. Legal Values ● 0 — Disabled ● 1 — Enabled Default Value 0 — Disabled Write Privilege Configure iDRAC License Required iDRAC Express or iDRAC Enterprise Dependency None iDRAC.NIC.
PAGE 328
Table 653. Details of iDRAC.NIC.VLanPort attribute (continued) Dependency None iDRAC.NIC.VLanPriority (Read Only) Table 654. Details of iDRAC.NIC.VLanPriority attribute Description Specifies the VLAN priority for the network VLAN configuration. NOTE: This object is applicable only to iDRAC on Racks and Towers. Legal Values Integral values: 0–7 Default Value 0 Write Privilege Configure iDRAC License Required iDRAC Express or iDRAC Enterprise Dependency None iDRAC.
PAGE 329
Table 656. Details of iDRAC.NICStatic.DNSDomainName attribute (continued) License Required iDRAC Express or iDRAC Enterprise Dependency None iDRAC.NTPConfigGroup To configure the properties of NTP server, use the objects in this group. iDRAC.NTPConfigGroup.NTP1 (Read or Write) Table 657. Details of iDRAC.NTPConfigGroup.NTP1 attribute Description Configure NTP Server 1 Address.
PAGE 330
Table 659. Details of iDRAC.NTPConfigGroup.NTP3 attribute (continued) License Required iDRAC Express or iDRAC Enterprise Dependency None iDRAC.NTPConfigGroup.NTPEnable (Read or Write) Table 660. Details of iDRAC.NTPConfigGroup.NTPEnable attribute Description On iDRAC, enable or disable NTP server access to iDRAC. Legal Values ● 0—Disabled ● 1—Enabled ● 2—Chassis Default Value 0—Disabled Write Privilege Configure iDRAC License Required iDRAC Express or iDRAC Enterprise Dependency None iDRAC.
PAGE 331
Table 662. Details of iDRAC.OS-BMC.AdminState (continued) Default Value 0 — Disabled Write Privilege Configure iDRAC License Required iDRAC Express or iDRAC Enterprise Dependency Can be set only if iDRAC.OS-BMC.PTCapability is set to Capable. iDRAC.OS-BMC.OSIpAddress (Read or Write) Table 663. Details of iDRAC.OS-BMC.OSIpAddress Description IPv4 address of the host Operating System. Legal Values Valid IPv4 Address Default Value 0.0.0.
PAGE 332
Table 665. Details of iDRAC.OS-BMC.PTMode (continued) Write Privilege Configure iDRAC License Required iDRAC Express or iDRAC Enterprise Dependency None iDRAC.OS-BMC.UsbNicIpAddress (Read or Write) Table 666. Details of iDRAC.OS-BMC.UsbNicIpAddress Description Displays the USB NIC IP address. Legal Values Valid IPv4 address Default Value 169.168.0 Write Privilege Configure iDRAC License Required iDRAC Express or iDRAC Enterprise Dependency None iDRAC.
PAGE 333
Table 668. Details of iDRAC.Racadm.Timeout (continued) Write Privilege Configure iDRAC License Required iDRAC Express or iDRAC Enterprise Dependency None iDRAC.Redfish The objects in this group provide configuration parameters for the Redfish interface to iDRAC. iDRAC.Redfish.Enable (Read or Write) Table 669. Details of iDRAC.Redfish.Enable Description Enables or disables Redfish service on iDRAC.
PAGE 334
iDRAC.Redfisheventing.DeliveryRetryIntervalInSeconds (Read or Write) Table 671. Details of iDRAC.Redfisheventing.DeliveryRetryIntervalInSeconds Description Specifies the intervals (in seconds) of retry attempts made for Redfish event delivery. Legal Values Value ranges from 5 to 60. Default Value 30 Write Privilege Configure iDRAC License Required RACADM Dependency None iDRAC.Redfisheventing.IgnoreCertificateErrors (Read Only) Table 672. Details of iDRAC.Redfisheventing.
PAGE 335
iDRAC.RemoteHosts.SMTPServerIPAddress (Read or Write) Table 674. Details of iDRAC.RemoteHosts.SMTPServerIPAddress Description IPv4 or IPv6 address of the network SMTP server. Legal Values String representing a valid SMTP server IPv4 or IPv6 address Default Value 0.0.0.0 Write Privilege Configure iDRAC License Required iDRAC Express or iDRAC Enterprise Dependency None iDRAC.RFS To configure Remote file share access to iDRAC, use the object in this group.
PAGE 336
iDRAC.RFS.WriteProtected (Read Only) Description RFS Write Protection Legal Values ● Read Only-0 ● Read Write-1 Default Value 0 Write Privilege Server Configuration License Required iDRAC Enterprise Dependancy None iDRAC.RSM The objects in this group manage the Rack Style Management (RSM) settings. iDRAC.RSM.RSMCapability (Read Only) Table 677. Details of iDRAC.RSM.RSMCapability Description Specifies the status of RSM capability.
PAGE 337
iDRAC.SecureDefaultPassword.ForceChangePassword (Read or Write) Description Enables or disables force change password. Legal Values ● 1 - True ● 0 - False Default Value 0 - False Write Privilege Server Control License Required iDRAC Enterprise Dependency Not applicable iDRAC.Security Use the objects in this group to configure SSL certificate signing request settings. For the country code, see http://www.iso.org/iso/home/standards/country_codes.htm. iDRAC.Security.
PAGE 338
iDRAC.Security.CsrEmailAddr (Read or Write) Table 681. Details of iDRAC.Security.CsrEmailAddr Description Specifies the CSR email address. Legal Values Valid email address string of up to 254 ASCII characters. Default Value Not Applicable Write Privilege Configure iDRAC License Required iDRAC Express or iDRAC Enterprise Dependency None iDRAC.Security.CsrKeySize (Read or Write) Table 682. Details of iDRAC.Security.CsrKeySize Description Specifies the SSL asymmetric key size for the CSRs.
PAGE 339
Table 684. Details of iDRAC.Security.CsrOrganizationName (continued) Legal Values String of up to 254 ASCII characters Default Value Not Applicable Write Privilege Configure iDRAC License Required iDRAC Express or iDRAC Enterprise Dependency None iDRAC.Security.CsrOrganizationUnit (Read or Write) Table 685. Details of iDRAC.Security.CsrOrganizationUnit Description Specifies the CSR Organization Unit (OU).
PAGE 340
Table 687. Details of iDRAC.Security.CsrSubjectAltName attribute (continued) Write Privilege Configure iDRAC License Required iDRAC Express or iDRAC Enterprise Dependency None iDRAC.Security.FIPSMode (Read or Write) Table 688. Details of iDRAC.Security.FIPSMode Description Enables or disables the FIPS mode compliance.
PAGE 341
Table 689. Details of iDRAC.Serial.BaudRate (continued) Dependency None iDRAC.Serial.Command (Read or Write) Table 690. Details of iDRAC.Serial.Command Description Specifies a serial command that is executed after the user logs in to the serial console interface. Legal Values String of up to 128 ASCII characters Default Value Not Applicable Write Privilege Configure iDRAC License Required iDRAC Express or iDRAC Enterprise Dependency None iDRAC.Serial.Enable (Read or Write) Table 691.
PAGE 342
iDRAC.Serial.IdleTimeout (Read or Write) Table 693. Details of iDRAC.Serial.IdleTimeout Description The maximum number of seconds to wait before an idle serial console session is disconnected. Legal Values ● 0 — No timeout ● Integral values: 60–10800 Default Value 300 Write Privilege Configure iDRAC License Required iDRAC Express or iDRAC Enterprise Dependency None iDRAC.Serial.NoAuth (Read or Write) Table 694. Details of iDRAC.Serial.
PAGE 343
Table 695. Details of iDRAC.SerialRedirection.Enable (continued) Dependency None iDRAC.SerialRedirection.QuitKey (Read or Write) Table 696. Details of iDRAC.SerialRedirection.QuitKey Description This key or key combination terminates the Virtual Console when using the console COM2 command. Legal Values Ctrl key followed by alphabets (a-z or A-Z), ^\ Default Value ^\ Write Privilege Configure iDRAC License Required iDRAC Express or iDRAC Enterprise Dependency None iDRAC.
PAGE 344
Table 698. Details of iDRAC.serverboot.FirstBootDevice (continued) ● ● ● ● SD (Local SD Card) F10 (Lifecycle Controller) F11 (BIOS Boot Manager) Attached vFlash Partition Label Default value Normal Write Privilege Login and configure iDRAC License Required iDRAC Express or iDRAC Enterprise Dependency None iDRAC.ServiceModule The objects in this group manages the properties of the ISM modules. iDRAC.ServiceModule.
PAGE 345
Write Privilege Configure iDRAC License Required iDRAC Basic Dependancy None iDRAC.ServiceModule.HostSNMPGet Table 700. Details of iDRAC.ServiceModule.HostSNMPGet attribute Description Enable or disable SNMP get via host OS. Legal Values ● 0 - Disabled ● 1 - Enabled, Default - 0 Default Value 0—Default Write Privilege Not Applicable License Required RACADM Dependency None iDRAC.ServiceModule.iDRACHardReset (Read or Write) Table 701. Details of iDRAC.ServiceModule.
PAGE 346
iDRAC.ServiceModule.OMSAPresence (Read Only) Table 703. Details of iDRAC.ServiceModule.OMSAPresence Description Verifies if OMSA is present. Legal Values ● 0 — Not Present ● 1 — Present ● 2 — NA Default Value 2 — NA License Required iDRAC Express or iDRAC Enterprise Dependency None iDRAC.ServiceModule.OSInfo (Read or Write) Table 704. Details of iDRAC.ServiceModule.OSInfo Description Provides information about operating system through iDRAC Service Module.
PAGE 347
Table 706. Details of iDRAC.ServiceModule.ServiceModuleState (continued) Write Privilege Configure iDRAC License Required iDRAC Express or iDRAC Enterprise Dependency None iDRAC.ServiceModule.ServiceModuleVersion (Read) Table 707. Details of iDRAC.ServiceModule.ServiceModuleVersion Description Displays the installed version of iDRAC Service Module. Legal Values None Default Value None License Required iDRAC Express or iDRAC Enterprise Dependency None iDRAC.ServiceModule.
PAGE 348
iDRAC.ServiceModule.WatchdogResetTime (Read and Write) Table 709. Details of iDRAC.ServiceModule.WatchdogResetTime Description Configures the system reset time (unit in seconds) on watchdog alert. Legal Values Values in range 60–720 Default Value 480 Write Privilege Configure iDRAC License Required iDRAC Express or iDRAC Enterprise Dependency If the iDRAC.ServiceModule.WatchdogState object is ‘Disabled’, then the value cannot be set. iDRAC.ServiceModule.WatchdogState (Read and Write) Table 710.
PAGE 349
Table 711. Details of iDRAC.SmartCard.SmartCardCRLEnable (continued) Legal Values ● 0 — Disabled ● 1 — Enabled Default Value Not Applicable Write Privilege Configure iDRAC and configure user License Required iDRAC Enterprise Dependency To log on, enable Smart Card. iDRAC.SmartCard.SmartCardLogonEnable (Read or Write) Table 712. Details of iDRAC.SmartCard.SmartCardLogonEnable Description Enables or disables Smart card login support.
PAGE 350
iDRAC.SNMP.AgentEnable (Read or Write) Table 714. Details of iDRAC.SNMP.AgentEnable Description Enables or disables the SNMP Agent on the iDRAC. Legal Values ● 0 — Disabled ● 1 — Enabled Default Value 1 — Enabled Write Privilege Configure iDRAC License Required iDRAC Express or iDRAC Enterprise Dependency None iDRAC.SNMP.AlertPort (Read or Write) Table 715. Details of iDRAC.SNMP.AlertPort Description Specifies the SNMP alert port for traps.
PAGE 351
Table 717. Details of iDRAC.SNMP.SNMPProtocol (continued) Default Value 0 — All Write Privilege Configure iDRAC License Required iDRAC Express or iDRAC Enterprise Dependency None iDRAC.SNMP.TrapFormat (Read or Write) Table 718. Details of iDRAC.SNMP.TrapFormat Description Specifies the SNMP format. Legal Values ● 0 — SNMPv1 ● 1 — SNMPv2 ● 2 — SNMPv3 Default Value 0 — SNMPv1 Write Privilege Configure iDRAC License Required iDRAC Express or iDRAC Enterprise Dependency None iDRAC.SNMP.
PAGE 352
iDRAC.SNMP.Alert.Enable (Read or Write) Table 720. Details of iDRAC.SNMP.Alert.Enable Description Enables or disables SNMP alert for the given index. Legal Values ● 0 — Disabled ● 1 — Enabled Default Value Not Applicable Write Privilege Configure iDRAC License Required None Dependency None iDRAC.SNMP.Alert.SNMPv3UserID (Read Only) Table 721. Details of iDRAC.SNMP.Alert.SNMPv3UserID Description Indicates the index of the user to which this alert is configured.
PAGE 353
iDRAC.SSH.Enable (Read or Write) Table 723. Details of iDRAC.SSH.Enable Description Enables or disables SSH. Legal Values ● 0 — Disabled ● 1 — Enabled Default Value 1 — Enabled Write Privilege Configure iDRAC License Required iDRAC Express or iDRAC Enterprise Dependency None iDRAC.SSH.Port (Read or Write) Table 724. Details of iDRAC.SSH.Port Description Specifies the port number for the iDRAC SSH interface.
PAGE 354
iDRAC.SupportAssist.HostOSProxyAddress Table 726. Details of iDRAC.SupportAssist.HostOSProxyAddress Description Host OS proxy address. Legal Values String of 0 to 256 characters length Default Value NA License Required RACADM Dependency HostOSProxyConfigured should be 1 - Yes iDRAC.SupportAssist.HostOSProxyConfigured Table 727. Details of iDRAC.SupportAssist.HostOSProxyConfigured Description Indicates whether Host OS uses proxy configuration to connect to Internet.
PAGE 355
Table 729. Details of iDRAC.SupportAssist.HostOSProxyPort (continued) Dependency HostOSProxyConfigured should be 1=Yes iDRAC.SupportAssist.HostOSProxyUserName Table 730. Details of iDRAC.SupportAssist.HostOSProxyUserName Description Host OS proxy password. Legal Values String of 0 to 64 characters length Default Value NA License Required RACADM Dependency HostOSProxyConfigured should be Yes-1 iDRAC.SysLog The objects in this group provide the properties for configuration of the SMTP server.
PAGE 356
Table 732. Details of iDRAC.SysLog.PowerLogEnable (continued) Dependency None iDRAC.SysLog.PowerLogInterval (Read or Write) Table 733. Details of iDRAC.SysLog.PowerLogInterval Description Configure time delay for power logging. Legal Values Integral values: 1–1440 Default Value 5 Write Privilege Configure iDRAC License Required iDRAC Enterprise Dependency None iDRAC.SysLog.Server1 (Read or Write) Table 734. Details of iDRAC.SysLog.Server1 Description Name of remote syslog server 1.
PAGE 357
iDRAC.SysLog.Server3 (Read or Write) Table 736. Details of iDRAC.SysLog.Server3 Description Name of remote syslog server 3. Legal Values String of up to 63 ACSII characters Default Value Not Applicable Write Privilege Configure iDRAC License Required iDRAC Enterprise Dependency None iDRAC.SysLog.SysLogEnable (Read or Write) Table 737. Details of iDRAC.SysLog.SysLogEnable Description Enables or disables remote syslog.
PAGE 358
iDRAC.Telnet.Port (Read or Write) Table 739. Details of iDRAC.Telnet.Port Description Specifies the port number for the iDRAC Telnet interface. Legal Values Integral values: 1–65535 Default Value 23 Write Privilege Configure iDRAC License Required iDRAC Express or iDRAC Enterprise Dependency None iDRAC.Time The objects in this group enable you to manage time zone setting for iDRAC. iDRAC.Time.DayLightOffset (Read or Write) Table 740. Details of iDRAC.Time.
PAGE 359
iDRAC.Time.TimeZoneOffset (Read or Write) Table 742. Details of iDRAC.Time.TimeZoneOffset Description Specifies the time zone offset (in minutes) from Greenwich Mean Time (GMT) or Coordinated Universal Time (UTC) to use for the iDRAC Time. Legal Values Integral values: -43200 – 46800 Default Value 0 Write Privilege Configure iDRAC License Required iDRAC Express or iDRAC Enterprise Dependency None iDRAC.
PAGE 360
Table 744. Details of iDRAC.Update.FwUpdateIPAddr (continued) License Required iDRAC Express or iDRAC Enterprise Dependency None iDRAC.Update.FwUpdatePath (Read or Write) Table 745. Details of iDRAC.Update.FwUpdatePath Description Specifies TFTP path where iDRAC firmware image resides on TFTP server. Path is relative to TFTP root folder. Legal Values String of up to 255 ACSII characters.
PAGE 361
Table 747. Details of iDRAC.USB.ConfigurationXML attribute (continued) Default Value Enabled while server has default credential settings only. Write Privilege Server Control License Required iDRAC Express and iDRAC Enterprise Dependency Not Applicable iDRAC.USB.ManagementPortMode (Read Only) Table 748. Details of iDRAC.USB.ManagementPortMode attribute Description Displays the front panel USB mode.
PAGE 362
iDRAC.UserDomain The objects in this group enable you to manage the Active Directory user domain names. This group is indexed from 1 to 40. iDRAC.UserDomain.Name (Read or Write) Table 750. Details of iDRAC.UserDomain.Name attribute Description Specifies the Active Directory user domain name for a given index. Legal Values String of up to 255 ACSII characters Default Value Not Applicable Write Privilege Configure iDRAC License Required iDRAC Express or iDRAC Enterprise Dependency None iDRAC.
PAGE 363
Table 752. Details of iDRAC.Users.IpmiLanPrivilege attribute (continued) Default Value 15 — No access Write Privilege Configure iDRAC License Required iDRAC Express or iDRAC Enterprise Dependency Both user name and password must be configured prior to setting this object. iDRAC.Users.IpmiSerialPrivilege (Read or Write) Table 753. Details of iDRAC.Users.IpmiSerialPrivilege attribute Description Specifies the maximum IPMI Serial privilege.
PAGE 364
Table 755. Details of iDRAC.Users.Password attribute (continued) License Required iDRAC Express or iDRAC Enterprise Dependency Cannot be set without first setting the user name. iDRAC.Users.SHA256Password (Read or Write) Table 756. Details of iDRAC.Users.SHA256Password attribute Description Indicates the SHA256 hash of the password.
PAGE 365
Table 759. Details of iDRAC.Users.SHA1v3Key attribute (continued) Legal Values String of 40 characters Default Value Not Applicable Write Privilege Configure iDRAC and Configure User License Required iDRAC Express Dependency User name must be configured prior to setting SHA1v3Key. iDRAC.Users.SNMPv3AuthenticationType (Read or Write) Table 760. Details of iDRAC.Users.SNMPv3AuthenticationType attribute Description Configure SNMPv3 authentication protocol type.
PAGE 366
Table 762. Details of iDRAC.Users.SNMPv3PrivacyType attribute (continued) Default Value 2 — AES Write Privilege Configure iDRAC and Configure User License Required iDRAC Express or iDRAC Enterprise Dependency None iDRAC.Users.SolEnable (Read or Write) Table 763. Details of iDRAC.Users.SolEnable attribute Description Enables or Disables SOL for the user.
PAGE 367
Table 765. Details of iDRAC.vflashpartition.AccessType attribute (continued) Legal Values ● 1 — Read Only ● 0 — Read Write Default value 1 — Read Only Write Privilege Login and configure iDRAC License Required iDRAC Enterprise Dependency vFlash SD card must be enabled. Partition at the specified index must be created. iDRAC.vflashpartition.AttachState (Read or Write) Table 766. Details of iDRAC.vflashpartition.
PAGE 368
Table 768. Details of iDRAC.vflashpartition.FormatType attribute (continued) Write Privilege Login and configure iDRAC License Required iDRAC Enterprise Dependency vFlash SD card must be enabled. Partition at the specified index must be created. iDRAC.vflashpartition.Size (Read or Write) Table 769. Details of iDRAC.vflashpartition.Size attribute Description Specifies the Size of the vFlash SD partition.
PAGE 369
iDRAC.vflashsd.Enable (Read or Write) Table 772. Details of iDRAC.vflashsd.Enable attribute Description Enables or disables the vFlash SD card on iDRAC. Legal Values ● 0 — Disabled ● 1 — Enabled Default value 0 — Disabled Write Privilege Login and configure iDRAC License Required iDRAC Enterprise Dependency vFlash SD card must be enabled. iDRAC.vflashsd.Health (Read or Write) Table 773. Details of iDRAC.vflashsd.Health attribute Description Specifies current health status of the vFlash SD Card.
PAGE 370
Table 775. Details of iDRAC.vflashsd.Licensed attribute (continued) Default value None Write Privilege Login and configure iDRAC License Required iDRAC Enterprise Dependency vFlash SD card must be enabled. iDRAC.vflashsd.Size (Read or Write) Table 776. Details of DRAC.vflashsd.Size attribute Description Specifies the remaining size of the vFlash SD card for usage. Legal Values Integer value in MB.
PAGE 371
Table 778. Details of iDRAC.VirtualConsole.AccessPrivilege attribute (continued) Write Privilege Configure iDRAC License Required iDRAC Express (For Blades) or iDRAC Enterprise Dependency None iDRAC.VirtualConsole.AttachState (Read or Write) Table 779. Details of iDRAC.VirtualConsole.AttachState attribute Description Specifies the Attach State for the Virtual Console.
PAGE 372
Table 781. Details of iDRAC.VirtualConsole.EncryptEnable attribute (continued) License Required iDRAC Express (For Blades) or iDRAC Enterprise Dependency None iDRAC.VirtualConsole.LocalVideo (Read or Write) Table 782. Details of iDRAC.VirtualConsole.LocalVideo attribute Description Enables or disables the local server video.
PAGE 373
Table 784. Details of iDRAC.VirtualConsole.PluginType attribute (continued) Dependency None iDRAC.VirtualConsole.Port (Read or Write) Table 785. Details of iDRAC.VirtualConsole.Port attribute Description Specifies the virtual KVM port. Legal Values Integral values: 1–65535 Default Value 5900 Write Privilege Configure iDRAC License Required iDRAC Express (For Blades) or iDRAC Enterprise Dependency None iDRAC.VirtualConsole.Timeout (Read or Write) Table 786. Details of iDRAC.VirtualConsole.
PAGE 374
Table 787. Details of iDRAC.VirtualMedia.Attached attribute (continued) License Required iDRAC Express (For Blades) or iDRAC Enterprise Dependency None iDRAC.VirtualMedia.BootOnce (Read or Write) Table 788. Details of iDRAC.VirtualMedia.BootOnce attribute Description Enables or disables the virtual media boot once feature of the iDRAC.
PAGE 375
Table 790. Details of iDRAC.VirtualMedia.EncryptEnable attribute (continued) Dependency None iDRAC.VirtualMedia.FloppyEmulation (Read or Write) Table 791. Details of iDRAC.VirtualMedia.FloppyEmulation attribute Description Enables of disables floppy emulation of the attached virtual media. Legal Values ● 0 — Disabled ● 1 — Enabled Default value 0 — Disabled Write Privilege Virtual Media License Required iDRAC Express (For Blades) or iDRAC Enterprise Dependency None iDRAC.VirtualMedia.
PAGE 376
iDRAC.VNCServer.LowerEncryptionBitLength (Read or Write) Table 793. Details of iDRAC.VNCServer.LowerEncryptionBitLength attribute Description Lower encryption bit length. Legal Values ● 0 — Disabled (Auto Negotiate) ● 1 — Enabled (128-Bit or Higher) Default Value 0 — Disabled (Auto Negotiate) Write Privilege Login or configure iDRAC License Required iDRAC Enterprise Dependency None iDRAC.VNCServer.Password (Read or Write) Table 794. Details of iDRAC.VNCServer.
PAGE 377
Table 796. Details of iDRAC.VNCServer.SSLEncryptionBitLength attribute (continued) Default value 0 — Disabled Write Privilege iDRAC Configure License Required iDRAC Enterprise Dependency None iDRAC.VNCServer.Timeout (Read or Write) Table 797. Details of iDRAC.VNCServer.Timeout attribute Description VNC server idle timeout period in seconds.
PAGE 378
Table 799. Details of iDRAC.WebServer.Enable attribute (continued) Legal Values ● 0 — Disabled ● 1 — Enabled Default Value 1 — Enabled Write Privilege Configure iDRAC License Required iDRAC Express or iDRAC Enterprise Dependency None iDRAC.WebServer.HostHeaderCheck(Read or Write) Table 800. Details of iDRAC.WebServer.HostHeaderCheck attribute Description This attribute when enabled enforces the HTTP Host request header to be validated.
PAGE 379
Table 802. Details of iDRAC.WebServer.HttpsPort attribute (continued) Write Privilege Configure iDRAC License Required iDRAC Express or iDRAC Enterprise Dependency None iDRAC.Webserver.Httpsredirection (Read or Write) Table 803. Details of iDRAC.Webserver.Httpsredirection attribute Description Enables or disables redirection from the http port (default — 80) to https (default — 443).
PAGE 380
Table 805. Details of iDRAC.WebServer.ManualDNSEntry attribute (continued) Dependency None iDRAC.WebServer.MaxNumberOfSessions (Read Only) Description Max session allowed Legal Values ● Integral values from RestUI to iDRAC Default Values ● 8 Write Privilege Configure iDRAC License Required iDRAC Basic Dependancy None iDRAC.WebServer.SSLEncryptionBitLength (Read or Write) Table 806. Details of iDRAC.WebServer.SSLEncryptionBitLength attribute Description Indicates the web server encryption state.
PAGE 381
iDRAC.webServer.TitleBarOptionCustom (Read or Write) Table 808. Details of iDRAC.webServer.TitleBarOptionCustom attribute Description Specifies the custom title when the title bar option is Custom. Legal Values String of up to 30 ASCII characters Default Value String of up to 30 ASCII characters Write Privilege Configure iDRAC License Required iDRAC Express or iDRAC Enterprise Dependency None iDRAC.WebServer.Timeout (Read or Write) Table 809. Details of iDRAC.WebServer.
PAGE 382
BIOS.BiosBootSettings.BootSeq (Read or Write) Table 811. Details of BIOS.BiosBootSettings.BootSeq attribute Description Determines the Bios start sequence of the system. Legal Values None Default Value Not Applicable Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Dependency Read Only if BootMode is set to UEFI NOTE: If BootMode is set to UEFI, legacy boot settings are not available in the system.
PAGE 383
BIOS.BiosBootSettings.HddFailover (Read or Write) Table 814. Details of BIOS.BiosBootSettings.HddFailover attribute Description Specifies the devices in the Hard-Disk Drive Sequence menu that are attempted in the boot sequence. This property applies to BIOS Boot Mode only, and is disabled when Boot Mode is set to UEFI. When set to Disabled (default), only the first Hard-Disk device in the list is attempted to boot.
PAGE 384
Legal Values String of range 0-255 Default Value Not Applicable Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Dependency Not applicable BIOS.BiosBootSettings.SetBootOrderEn (Read or Write) Description The SetBootOrderEn fields specify a list of Fqdds representing the boot option Enabled to be applied on the next boot.
PAGE 385
BIOS.EmbServerMgmt.FrontLcd (Read or Write) Table 819. Details of BIOS.EmbServerMgmt.FrontLcd attribute Description Allows to display the default (Model name and number) or a user-defined string in the front-panel LCD. To modify the advanced features of the front-panel LCD, press F2 during boot to enter System Setup and then select iDRAC Settings.
PAGE 386
BIOS.IntegratedDevices.EmbNic1 (Read or Write) Table 821. Details of BIOS.IntegratedDevices.EmbNic1 attribute Description Enables or disables the operating system interface of the embedded NIC1. Legal Values ● ● ● ● Default Value Not Applicable Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Dependency None Enabled EnabledPxe EnablediScsi Disabled BIOS.IntegratedDevices.EmbNic1Nic2 (Read or Write) Table 822. Details of BIOS.IntegratedDevices.
PAGE 387
BIOS.IntegratedDevices.EmbNic3 (Read or Write) Table 824. Details of BIOS.IntegratedDevices.EmbNic3 attribute Description Enables or disables the operating system interface of the embedded NIC3. Legal Values ● ● ● ● Default Value Not Applicable Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Dependency None Enabled EnabledPxe EnablediScsi Disabled BIOS.IntegratedDevices.EmbNic3Nic4 (Read or Write) Table 825. Details of BIOS.IntegratedDevices.
PAGE 388
BIOS.IntegratedDevices.EmbVideo (Read or Write) Table 827. Details of IOS.IntegratedDevices.EmbVideo attribute Description Enables or disables the BIOS support for the embedded video controller. Legal Values ● Enabled ● Disabled Default Value Not Applicable Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Dependency None BIOS.IntegratedDevices.GlobalSlotDriverDisable Table 828. Details of BIOS.IntegratedDevices.
PAGE 389
BIOS.IntegratedDevices.IntegratedNetwork2 (Read or Write) Table 830. Details of BIOS.IntegratedDevices.IntegratedNetwork2 attribute Description Enables or disables the integrated network card 2. Legal Values ● Enabled ● DisabledOS Default Value Not Applicable Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Dependency None BIOS.IntegratedDevices.IntegratedRaid (Read or Write) Table 831. Details of BIOS.IntegratedDevices.
PAGE 390
BIOS.IntegratedDevices.InternalSdCard (Read or Write) Table 833. Details of BIOS.IntegratedDevices.InternalSdCard attribute Description Enables or disables the internal SD Card port. Legal Values ● On ● Off Default Value Not Applicable Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Dependency None BIOS.IntegratedDevices.InternalSdCardRedundancy (Read or Write) Table 834. Details of BIOS.IntegratedDevices.
PAGE 391
BIOS.IntegratedDevices.InternalUsb1 (Read or Write) Table 836. Details of BIOS.IntegratedDevices.InternalUsb1 attribute Description Enables or disables the internal USB port 1. Legal Values ● On ● Off Default Value Not Applicable Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Dependency None BIOS.IntegratedDevices.InternalUsb2 (Read or Write) Table 837. Details of BIOS.IntegratedDevices.
PAGE 392
BIOS.IntegratedDevices.IoatEngine (Read or Write) Table 839. Details of BIOS.IntegratedDevices.IoatEngine attribute Description Enables or disables the I/O Acceleration technology (I/OAT) option. Legal Values ● Enabled ● Disabled Default Value Not Applicable License Required iDRAC Express or iDRAC Enterprise Dependency None BIOS.IntegratedDevices.IONonPostedPrefetch Table 840. Details of BIOS.IntegratedDevices.
PAGE 393
Table 842. Details of BIOS.IntegratedDevices.OsWatchdogTimer attribute (continued) Legal Values ● Enabled ● Disabled Default Value Not Applicable Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Dependency None BIOS.IntegratedDevices.SriovGlobalEnable (Read or Write) Table 843. Details of BIOS.IntegratedDevices.SriovGlobalEnable attribute Description Enables or disables BIOS configuration of Single Root I/O Virtualization (SR-IOV) devices.
PAGE 394
Table 844. Details of BIOS.IntegratedDevices.UsbPorts attribute (continued) Legal Values ● All on ● Only back ports on ● All off Default Value Not Applicable Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Dependency None BIOS.MemSettings To manage memory-related configuration settings, use the objects in this group. BIOS.MemSettings.CorrEccSmi (Read or Write) Description Allows the system to log ECC corrected DRAM errors into the SEL log.
PAGE 395
BIOS.MemSettings.MemOpMode (Read or Write) Table 846. Details of BIOS.MemSettings.MemOpMode attribute Description Current memory operating mode. Legal Values ● ● ● ● ● Default Value Not Applicable Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Dependency None OptimizerMode SpareMode MirrorMode AdvEccMode SpareWithAdvEccMode BIOS.MemSettings.MemOptimizer (Read or Write) Table 847. Details of BIOS.MemSettings.
PAGE 396
BIOS.MemSettings.MemTest (Read or Write) Table 849. Details of BIOS.MemSettings.MemTest attribute Description Specifies whether BIOS software-based system memory tests are conducted during POST. Legal Values ● Enabled ● Disabled Default Value Not Applicable Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Dependency None BIOS.MemSettings.NodeInterleave (Read or Write) Table 850. Details of BIOS.MemSettings.
PAGE 397
BIOS.MemSettings.RedundantMemCfgValid (Read or Write) Table 852. Details of BIOS.MemSettings.RedundantMemCfgValid attribute Description Redundant Memory Configuration Valid Legal Values ● Invalid ● Valid Default Value Not Applicable Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Dependency None BIOS.MemSettings.RedundantMemInUse (Read Only) Table 853. Details of BIOS.MemSettings.
PAGE 398
Table 855. Details of BIOS.MemSettings.SnoopFilter attribute (continued) NOTE: This attribute is not supported for 13th generation servers. Legal Values ● Enabled ● Disabled Default Value Not Applicable Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Dependency None BIOS.MemSettings.SnoopMode (Read or Write) Description Allows tuning of memory performances under different memory bandwidths. The optimal Snoop Mode setting is highly dependent on workload type.
PAGE 399
BIOS.MemSettings.SysMemSpeed (Read or Write) Table 857. Details of BIOS.MemSettings.SysMemSpeed attribute Description Indicates the current clock frequency of the main memory. Legal Values None Default Value Not Applicable Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Dependency None BIOS.MemSettings.SysMemType (Read or Write) Table 858. Details of BIOS.MemSettings.
PAGE 400
Table 860. Details of BIOS.MemSettings.VideoMem attribute (continued) Default Value Not Applicable Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Dependency None BIOS.MiscSettings To manage the miscellaneous objects settings, use the object in this group. BIOS.MiscSettings.AssetTag (Read or Write) Table 861. Details of BIOS.MiscSettings.AssetTag attribute Description Displays the current asset tag and the asset tag can be modified.
PAGE 401
Table 863. Details of BIOS.MiscSettings.InSystemCharacterization attribute (continued) ● Disabled Default Value Not Applicable License Required RACADM Dependency None BIOS.MiscSettings.NumLock (Read or Write) Table 864. Details of BIOS.MiscSettings.
PAGE 402
Table 866. Details of BIOS.MiscSettings.SystemUefiShell attribute (continued) License Required iDRAC Express or iDRAC Enterprise Dependency None BIOS.MiscSettings.SysMgmtNVByte1 (Read or Write) Table 867. Details of attribute Description Indicates the system management NVRAM byte 1. Legal Values Integer Default Value Not Applicable Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Dependency None BIOS.MiscSettings.SysMgmtNVByte2 (Read or Write) Table 868.
PAGE 403
BIOS.MiscSettings.ForceInt10 (Read or Write) Table 870. Details of BIOS.MiscSettings.ForceInt10 attribute Description Specifies if the system BIOS will load the legacy video (INT 10h) option ROM from the video controller. Legal Values ● Enabled ● Disabled Default Value Not Applicable Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Dependency None BIOS.NetworkSettings The objects in this group manage the iSCSI devices. BIOS.NetworkSettings.
PAGE 404
Table 872. Details of BIOS.OneTimeBoot.OneTimeBootMode attribute (continued) Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Dependency None NOTE: On a Dell 13th generation of PowerEdge server, to set the value from OneTimeBootMode to OneTimeUefiBootSeq, you must boot the server in UEFI mode. BIOS.OneTimeBoot.OneTimeBootSeqDev (Read or Write) Table 873. Details of BIOS.OneTimeBoot.
PAGE 405
Table 875. Details of BIOS.OneTimeBoot.OneTimeHddSeqDev attribute (continued) License Required iDRAC Express or iDRAC Enterprise Dependency Read Only if OneTimeBootMode is not set to OneTimeHddSeq BIOS.OneTimeBoot.OneTimeUefiBootSeqDev (Read or Write) Table 876. Details of BIOS.OneTimeBoot.OneTimeUefiBootSeqDev attribute Description Configure the one time UEFI Boot Sequence device.
PAGE 406
Table 878. Details of BIOS.ProcSettings.DataReuse attribute (continued) Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Dependency None BIOS.ProcSettings.DcuIpPrefetcher (Read or Write) Table 879. Details of BIOS.ProcSettings.DcuIpPrefetcher attribute Description Enables or disables Data Cache Unit (DCU) IP Prefetcher.
PAGE 407
Table 881. Details of BIOS.ProcSettings.DmaVirtualization attribute (continued) Dependency None BIOS.ProcSettings.DynamicCoreAllocation (Read or Write) Table 882. Details of BIOS.ProcSettings.DynamicCoreAllocation attribute Description Enables or disables the operating system capability to set the logical processors in idle state which helps to reduce power consumption.
PAGE 408
BIOS.ProcSettings.Proc1Brand (Read or Write) Table 885. Details of BIOS.ProcSettings.Proc1Brand attribute Description Provides the processor brand name. Legal Values None Default Value Not Applicable Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Dependency None BIOS.ProcSettings.Proc1ControlledTurbo (Read or Write) Table 886. Details of BIOS.ProcSettings.Proc1ControlledTurbo attribute Description Controls the turbo engagement.
PAGE 409
BIOS.ProcSettings.Proc1L2Cache (Read or Write) Table 888. Details of BIOS.ProcSettings.Proc1L2Cache attribute Description Amount of memory in the corresponding processor cache. Legal Values None Default Value Not Applicable Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Dependency None BIOS.ProcSettings.Proc1L3Cache (Read or Write) Table 889. Details of BIOS.ProcSettings.Proc1L3Cache attribute Description Amount of memory in the corresponding processor cache.
PAGE 410
Table 891. Details of BIOS.ProcSettings.Proc2Brand attribute (continued) Default Value Not Applicable Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Dependency None BIOS.ProcSettings.Proc2ControlledTurbo (Read or Write) Table 892. Details of BIOS.ProcSettings.Proc2ControlledTurbo attribute Description Controls the turbo engagement. NOTE: You can enable this option only when System Profile is set to Performance.
PAGE 411
Table 894. Details of BIOS.ProcSettings.Proc2Id attribute (continued) Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Dependency None BIOS.ProcSettings.Proc2L2Cache (Read or Write) Table 895. Details of BIOS.ProcSettings.Proc2L2Cache attribute Description AmountBIOS.ProcSettings.Proc2L2Cache (Read Only) of memory in the corresponding processor cache.
PAGE 412
BIOS.ProcSettings.Proc3Brand (Read or Write) Table 898. Details of BIOS.ProcSettings.Proc3Brand attribute Description Brand text provided by the processor manufacturer. Legal Values None Default Value Not Applicable Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Dependency None BIOS.ProcSettings.Proc3ControlledTurbo (Read or Write) Table 899. Details of BIOS.ProcSettings.Proc3ControlledTurbo attribute Description Controls the turbo engagement.
PAGE 413
BIOS.ProcSettings.Proc3Id (Read or Write) Table 901. Details of BIOS.ProcSettings.Proc3Id attribute Description Processor's family model and stepping values. Legal Values None Default Value Not Applicable Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Dependency None c(Read or Write) Table 902. Details of BIOS.ProcSettings.Proc3Id attribute Description Amount of memory in the corresponding processor cache.
PAGE 414
Table 904. Details of BIOS.ProcSettings.Proc3NumCores attribute (continued) Default Value Not Applicable Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Dependency None BIOS.ProcSettings.Proc4Brand (Read or Write) Table 905. Details of BIOS.ProcSettings.
PAGE 415
Table 907. Details of BIOS.Procsettings.Proc4Cores attribute (continued) Write Privilege Server control License Required RACADM Dependency Requires the DPAT Pro license to make it visible. It can be edited only if the Number of Cores per Processor is set to Custom. BIOS.ProcSettings.Proc4Id (Read or Write) Table 908. Details of BIOS.ProcSettings.Proc4Id attribute Description Processor's family model and stepping values.
PAGE 416
BIOS.ProcSettings.Proc4NumCores (Read or Write) Table 911. Details of BIOS.ProcSettings.Proc4NumCores attribute Description Number of cores in the processor package. Legal Values None Default Value Not Applicable Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Dependency None BIOS.ProcSettings.Proc64bit (Read or Write) Table 912. Details of BIOS.ProcSettings.Proc64bit attribute Description Specifies whether the installed processors support 64-bit extensions.
PAGE 417
Table 914. Details of BIOS.ProcSettings.ProcBusSpeed attribute (continued) Legal Values None Default Value Not Applicable Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Dependency None BIOS.ProcSettings.ProcConfigTdp (Read or Write) Table 915. Details of BIOS.ProcSettings.ProcConfigTdp attribute Description Allows to re-configure the Thermal Design Power (TDP) to lower levels.
PAGE 418
BIOS.ProcSettings.ProcCoreSpeed (Read or Write) Table 917. Details of vattribute Description Clock speed of the processor. Legal Values None Default Value Not Applicable Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Dependency None BIOS.ProcSettings.ProcDramPrefetcher (Read or Write) Table 918. Details of BIOS.ProcSettings.ProcDramPrefetcher attribute Description Enable to turn on the DRAM prefetch unit in the Northbridge.
PAGE 419
BIOS.ProcSettings.ProcHpcMode (Read or Write) Table 920. Details of BIOS.ProcSettings.ProcHpcMode attribute Description Configure processor's HPC mode. Legal Values ● Enabled ● Disabled Default Value Not Applicable Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Dependency None BIOS.ProcSettings.ProcHtAssist (Read or Write) Table 921. Details of BIOS.ProcSettings.
PAGE 420
BIOS.ProcSettings.ProcHyperTransport (Read or Write) Table 923. Details of BIOS.ProcSettings.ProcHyperTransport attribute Description Specifies the supported HyperTransport I/O Link Specification. Legal Values ● HT1 ● HT3 Default Value Not Applicable Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Dependency None BIOS.ProcSettings.ProcSoftwarePrefetcher (Read or Write) Table 924. Details of BIOS.ProcSettings.
PAGE 421
BIOS.ProcSettings.ProcX2Apic (Read or Write) Table 926. Details of BIOS.ProcSettings.ProcX2Apic attribute Description Enables or disables the X2APIC mode. NOTE: To enable BIOS.ProcSettings.ProcX2Apic, you must enable BIOS.ProcSettings.ProcVirtualization. Legal Values ● Enabled ● Disabled Default Value Disabled Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Dependency Read Only if the ProcVirtualization attribute is set to Disabled. BIOS.ProcSettings.
PAGE 422
BIOS.ProcSettings.RtidSetting (Read or Write) Table 929. Details of BIOS.ProcSettings.RtidSetting attribute Description Allocates more RTIDs to the remote socket increasing cache performance between the sockets. Legal Values ● Enabled ● Disabled Default Value Not Applicable Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Dependency None BIOS.ProxyAttributes The objects in this group manage the legacy boot protocol of LOM. BIOS.ProxyAttributes.
PAGE 423
Table 931. Details ofBIOS.ProxyAttributes.IntNic1PortnBootproto attribute (continued) ● None ● Pxe ● Iscsi Default Value Not Applicable Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Dependency None BIOS.PxeDev1Settings The objects in this group manage the PXE device settings. BIOS.PxeDev1Settings.PxeDevnInterface (Read or Write) Table 932. Details of BIOS.PxeDev1Settings.
PAGE 424
Table 934. Details of BIOS.PxeDev1Settings.PxeDevnVlanEnDis attribute (continued) Legal Values ● Enabled ● Disabled Default Value None Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Dependency None BIOS.PxeDev1Settings.PxeDevnVlanId (Read or Write) Table 935. Details of BIOS.PxeDev1Settings.PxeDevnVlanId attribute Description Indicates the VLAN ID for the specified PXE device. For the attribute PxeDevnVlanId, the value of n can be 1 — 4.
PAGE 425
Default Value Not Applicable Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Dependency Not applicable BIOS.SataSettings.eSataPort1 (Read or Write) Table 937. Details of IOS.SataSettings.eSataPort1 attribute Description Sets the drive type of the selected device. Legal Values ● Off ● Auto Default Value Not Applicable Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Dependency None BIOS.SataSettings.
PAGE 426
BIOS.SataSettings.eSataPort1Model (Read or Write) Table 940. Details of BIOS.SataSettings.eSataPort1Model attribute Description Displays the drive model of the selected device. Legal Values None Default Value Not Applicable Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Dependency None BIOS.SataSettings.SataPortA (Read or Write) Table 941. Details of BIOS.SataSettings.SataPortA attribute Description Sets the drive type of the selected device.
PAGE 427
Table 943. Details of BIOS.SataSettings.SataPortADriveType attribute (continued) Legal Values None Default Value Not Applicable Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Dependency None BIOS.SataSettings.SataPortAModel (Read or Write) Table 944. Details of BIOS.SataSettings.SataPortAModel attribute Description Displays the drive model of the selected device.
PAGE 428
Table 946. Details of BIOS.SataSettings.SataPortBCapacity attribute (continued) License Required iDRAC Express or iDRAC Enterprise Dependency None BIOS.SataSettings.SataPortBDriveType (Read or Write) Table 947. Details of BIOS.SataSettings.SataPortBDriveType attribute Description Indicates type of device attached to this SATA port. Legal Values None Default Value Not Applicable Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Dependency None BIOS.
PAGE 429
BIOS.SataSettings.SataPortCCapacity (Read or Write) Table 950. Details of BIOS.SataSettings.SataPortCCapacity attribute Description Displays the total capacity of a hard-disk drive. Legal Values None Default Value Not Applicable Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Dependency None BIOS.SataSettings.SataPortCDriveType (Read or Write) Table 951. Details of BIOS.SataSettings.
PAGE 430
Table 953. Details of BIOS.SataSettings.SataPortD attribute (continued) ● Auto Default Value Not Applicable Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Dependency Read Only if EmbSata is not set to AtaMode. BIOS.SataSettings.SataPortDCapacity (Read or Write) Table 954. Details of BIOS.SataSettings.SataPortDCapacity attribute Description Displays the total capacity of a hard-disk drive.
PAGE 431
Table 956. Details of BIOS.SataSettings.SataPortDModel attribute (continued) Dependency None BIOS.SataSettings.SataPortE (Read or Write) Table 957. Details of BIOS.SataSettings.SataPortE attribute Description Sets the drive type of the selected device. Legal Values ● Off ● Auto Default Value Not Applicable Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Dependency Read Only if EmbSata is not set to AtaMode. BIOS.SataSettings.
PAGE 432
BIOS.SataSettings.SataPortEModel (Read or Write) Table 960. Details of BIOS.SataSettings.SataPortEModel attribute Description Displays the drive model of the selected device. Legal Values None Default Value Not Applicable Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Dependency None BIOS.SataSettings.SataPortF (Read or Write) Table 961. Details of BIOS.SataSettings.SataPortF attribute Description Sets the drive type of the selected device.
PAGE 433
Table 963. Details of BIOS.SataSettings.SataPortFDriveType attribute (continued) Default Value Not Applicable Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Dependency None BIOS.SataSettings.SataPortFModel (Read or Write) Table 964. Details of BIOS.SataSettings.SataPortFModel attribute Description Displays the drive model of the selected device.
PAGE 434
BIOS.SataSettings.SataPortGDriveType (Read or Write) Table 967. Details of BIOS.SataSettings.SataPortGDriveType attribute Description Indicates type of device attached to this SATA port. Legal Values None Default Value Not Applicable Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Dependency None BIOS.SataSettings.SataPortGModel (Read or Write) Table 968. Details of IOS.SataSettings.
PAGE 435
Table 970. Details of BIOS.SataSettings.SataPortHCapacity attribute (continued) Legal Values None Default Value Not Applicable Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Dependency None BIOS.SataSettings.SataPortHDriveType (Read or Write) Table 971. Details of BIOS.SataSettings.SataPortHDriveType attribute Description Indicates type of device attached to this SATA port.
PAGE 436
Table 973. Details of BIOS.SataSettings.SataPortI attribute (continued) ● Auto Default Value Not Applicable Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Dependency None BIOS.SataSettings.SataPortICapacity (Read or Write) Table 974. Details of BIOS.SataSettings.SataPortICapacity attribute Description Displays the total capacity of a hard-disk drive. This property is not defined for removable-media devices such as optical drives.
PAGE 437
BIOS.SataSettings.SataPortJ (Read or Write) Table 977. Details of BIOS.SataSettings.SataPortJ attribute Description Sets the drive type of the selected device. When the Embedded SATA setting is in: ● ATA Mode, set this property to Auto to enable the BIOS support for the device. Select Off to turn off the BIOS support for the device. ● AHCI Mode or RAID Mode, the BIOS always enables support for the device.
PAGE 438
Table 980. Details of BIOS.SataSettings.SataPortJModel attribute (continued) Legal Values Not Applicable Default Value Not Applicable Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Dependency None BIOS.SataSettings.SecurityFreezeLock (Read or Write) Table 981. Details of BIOS.SataSettings.SecurityFreezeLock attribute Description Directs the Security Freeze Lock command to the Embedded SATA drives during POST.
PAGE 439
Table 982. Details of BIOS.SerialCommSettings.ConTermType attribute (continued) Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Dependency None BIOS.SerialCommSettings.ExtSerialConnector (Read or Write) Table 983. Details of BIOS.SerialCommSettings.ExtSerialConnector attribute Description Associate the External Serial Connector to Serial 1 or Serial 2 or Remote Access Device.
PAGE 440
Table 985. Details of BIOS.SerialCommSettings.RedirAfterBoot attribute (continued) Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Dependency None BIOS.SerialCommSettings.SerialComm (Read or Write) Table 986. Details of BIOS.SerialCommSettings.SerialComm attribute Description Controls the serial communication options.
PAGE 441
BIOS.SlotDisablement.Slot1 (Read or Write) Table 988. Details of BIOS.SlotDisablement.Slot1 attribute Description Control the configuration of the card installed in slot1. Legal Values ● Enabled ● Disabled ● BootDriverDisabled Default Value Not Applicable Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Dependency None BIOS.SlotDisablement.Slot2 (Read or Write) Table 989. Details of BIOS.SlotDisablement.
PAGE 442
BIOS.SlotDisablement.Slot4 (Read or Write) Table 991. Details of BIOS.SlotDisablement.Slot4 attribute Description Control the configuration of the card installed in slot 4. Legal Values ● Enabled ● Disabled ● BootDriverDisabled Default Value Not Applicable Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Dependency None BIOS.SlotDisablement.Slot5 (Read or Write) Table 992. Details of IOS.SlotDisablement.
PAGE 443
BIOS.SlotDisablement.Slot7 (Read or Write) Table 994. Details of BIOS.SlotDisablement.Slot7 attribute Description Control the configuration of the card installed in slot 7. Legal Values ● Enabled ● Disabled ● BootDriverDisabled Default Value Not Applicable Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Dependency None BIOS.SlotDisablement.Slot8 (Read or Write) Table 995. Details of BIOS.SlotDisablement.
PAGE 444
Table 996. Details of BIOS.SlotDisablement.Slot9 attribute (continued) NOTE: If multiple cards from the same manufacturer are managed using the same boot driver, select BootDriverDisabled for all the cards from the same manufacturer so that the Option ROM is not run. Legal Values ● Enabled ● Disabled ● BootDriverDisabled Default Value Not Applicable Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Dependency None BIOS.SlotDisablement.
PAGE 445
Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Dependency Not applicable BIOS.SysInformation.SysMfrContactInfo (Read or Write) Table 998. Details of BIOS.SysInformation.SysMfrContactInfo attribute Description Provides information about the Original Equipment Manufacturer of this system. Legal Values None Default Value Not Applicable Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Dependency None BIOS.SysInformation.
PAGE 446
BIOS.SysInformation.SystemManufacturer (Read or Write) Table 1001. Details of BIOS.SysInformation.SystemManufacturer attribute Description Provides the name of the Original Equipment Manufacturer of this system. Legal Values None Default Value Not Applicable Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Dependency None BIOS.SysInformation.SystemModelName (Read or Write) Table 1002. Details of BIOS.SysInformation.
PAGE 447
Table 1004. Details of BIOS.SysInformation.UefiComplianceVersion attribute (continued) Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Dependency None BIOS.SysProfileSettings To manage the system profile settings, use the objects in this group. BIOS.SysProfileSettings.CollaborativeCpuPerfCtrl (Read/Write) Table 1005. Details of BIOS.SysProfileSettings.CollaborativeCpuPerfCtrl attribute Description Enables or disables the CPU power management control.
PAGE 448
Table 1007. Details of BIOS.SysProfileSettings.EnergyPerformanceBias attribute (continued) ● BalancedEfficiency ● LowPower Default Value Not Applicable Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Dependency None BIOS.SysProfileSettings.MemFrequency (Read or Write) Table 1008. Details of BIOS.SysProfileSettings.MemFrequency attribute Description Set the speed of the system memory to maximum performance, maximum reliability or a specific speed.
PAGE 449
BIOS.SysProfileSettings.MemPwrMgmt (Read or Write) Table 1010. Details of BIOS.SysProfileSettings.MemPwrMgmt attribute Description Enables or disables the memory to operate in power management mode. Legal Values ● Enabled ● Disabled Default Value Not Applicable Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Dependency None BIOS.SysProfileSettings.MemRefreshRate (Read or Write) Table 1011. Details of BIOS.SysProfileSettings.
PAGE 450
BIOS.SysProfileSettings.MonitorMwait (Read or Write) Table 1013. Details of BIOS.SysProfileSettings.MonitorMwait attribute Description Enables or disables Monitor or Mwait instructions. When C state is enabled in Custom mode, changing this setting does not affect system performance Legal Values ● Enabled ● Disabled Default Value Not Applicable Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Dependency Disabled only when SysProfileSettings.
PAGE 451
BIOS.SysProfileSettings.Proc2TurboCoreNum (Read or Write) Description Controls the number of Turbo Boost enabled cores for processor 2. By reducing the number of cores enabled with Turbo Boost, the maximum turbo frequency on the cores with Turbo Boost may be higher. Read-only unless System Profile is set to Custom. Legal Values ● ● ● ● ● Default Value Not Applicable Write Privilege Server Control All 1 2 4 6 License Required iDRAC Express or iDRAC Enterprise Dependency Not applicable BIOS.
PAGE 452
BIOS.SysProfileSettings.ProcPwrPerf (Read or Write) Table 1017. Details of BIOS.SysProfileSettings.ProcPwrPerf attribute Description Sets CPU power management to maximum performance operating system DBPM or System DBPM (DAPC) mode. Legal Values ● ● ● ● Default Value Not Applicable Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Dependency Read Only if SysProfileSettings.SysProfile is not set to Custom mode. MaxPerf MinPwr SysDbpm OsDbpm BIOS.SysProfileSettings.
PAGE 453
BIOS.SysProfileSettings.SysProfile (Read or Write) Table 1020. Details of BIOS.SysProfileSettings.SysProfile attribute Description Sets the System Profile to Performance Per Watt (DAPC), Performance Per Watt (OS) Performance Dense Configuration, or Custom mode.
PAGE 454
Table 1022. Details of IOS.SysProfileSettings.UncoreFrequency attribute (continued) License Required iDRAC Express or iDRAC Enterprise Dependency None BIOS.SysProfileSettings.WorkloadProfile (Read or Write) Description Allows optimization of performance based on the workload type. The WorkloadProfile setting is not a 'state'. Setting a workload profile is a one-time action that in turns modifies various BIOS settings to be optimized for the requested workload type.
PAGE 455
Table 1024. Details of BIOS.SysSecurity.AcPwrRcvry attribute (continued) ● Off ● Last Default Value Not Applicable Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Dependency Read Only if SysSecurity.AcPwrRcvry is set to Off. BIOS.SysSecurity.AcPwrRcvryDelay (Read or Write) Table 1025. Details of BIOS.SysSecurity.AcPwrRcvryDelay attribute Description Specifies how the system supports the staggering of power-up after AC power has been restored to the system.
PAGE 456
Table 1027. Details of BIOS.SysSecurity.Aesni attribute (continued) Default Value Not Applicable Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Dependency None BIOS.SysSecurity.BiosUpdateControl (Read or Write) Table 1028. Details of BIOS.SysSecurity.BiosUpdateControl attribute Description If this attribute is set to Unlocked, then all BIOS update is allowed.
PAGE 457
BIOS.SysSecurity.NmiButton (Read or Write) Table 1030. Details of BIOS.SysSecurity.NmiButton attribute Description Enables or disables the NMI button on the front panel. Legal Values ● Enabled ● Disabled Default Value Not Applicable Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Dependency None BIOS.SysSecurity.PasswordStatus (Read or Write) Table 1031. Details of BIOS.SysSecurity.PasswordStatus attribute Description Locks the system password.
PAGE 458
Table 1033. Details of BIOS.SysSecurity.SecureBoot attribute (continued) NOTE: BiosBootSettings.Bootmode must be set to UEFI and MiscSettings.ForceInt10 must be Disabled to operate this property. Legal Values ● Enabled ● Disabled Default Value Not Applicable Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Dependency None BIOS.SysSecurity.SecureBootPolicy (Read or Write) Description Allows selecting the Secure Boot Policy.
PAGE 459
BIOS.SysSecurity.SHA256SetupPassword (Read or Write) Table 1035. Details of BIOS.SysSecurity.SHA256SetupPassword attribute Description Indicates the SHA256 hash of the setup password. Legal Values String of 64 characters Default Value Not Applicable Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Dependency None BIOS.SysSecurity.SHA256SetupPasswordSalt (Read or Write) Table 1036. Details of BIOS.SysSecurity.
PAGE 460
Table 1038. Details of BIOS.SysSecurity.SysPassword attribute (continued) ● Only lower case alphabets are accepted. ● Special characters accepted are +, ", ,, -, ., /, ;, [, \, ], `. To enable password modification, J_EN_PASSWD must be installed. To clear the already configured password, use the option available under F2 (system setup) during system start.
PAGE 461
Table 1041. Details of BIOS.SysSecurity.TcmActivation attribute (continued) Default Value Not Applicable Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Dependency None BIOS.SysSecurity.TcmClear (Read or Write) Table 1042. Details of BIOS.SysSecurity.TcmClear attribute Description Warns that clearing the TPM causes loss of all keys in the TPM. It may affect starting the operating system.
PAGE 462
Table 1044. Details of BIOS.SysSecurity.TpmActivation attribute (continued) Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Dependency Read Only if SysSecurity.TpmSecurity is set to Off. BIOS.SysSecurity.TpmClear (Read or Write) Table 1045. Details of BIOS.SysSecurity.TpmClear attribute Description Warns that clearing the TPM causes loss of all keys in the TPM. It may affect starting the operating system.
PAGE 463
BIOS.SysSecurity.TpmPpiBypassClear Table 1047. Details of BIOS.SysSecurity.TpmPpiBypassClear attribute Description Clears the Physical Presence Interface (PPI) Advanced Configuration and Power Interface (ACPI) and enables the operating system to by-pass the PPI-related prompts. Legal Values ● Enabled ● Disabled Default Value NA Write Privilege Server control License Required RACADM Dependency None BIOS.SysSecurity.TpmPpiBypassProvision Table 1048. Details of BIOS.SysSecurity.
PAGE 464
BIOS.SysSecurity.TPMStatus (Read Only) Table 1050. Details of BIOS.SysSecurity.TPMStatus attribute Description Displays the status of TPM. Legal Values String of up to 64 ASCII characters. Default Value Not Applicable Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Dependency None BIOS.SysSecurity.UefiVariableAccess (Read or Write) Description Provides varying degrees of securing UEFI variables.
PAGE 465
BIOS.UefiBootSettings.UefiPxeIpVersion (Read or Write) Table 1052. Details of BIOS.UefiBootSettings.UefiPxeIpVersion attribute Description Enables to select the IPv4 PXE booting (default) or IPv6 PXE booting when in UEFI boot mode. This property is disabled in BIOS boot mode. If this property is modified, the PXE options in the UEFI boot sequence is replaced on the next restart.
PAGE 466
FC.FCDevice.EFIVersion (Read Only) Table 1055. Details of attribute Description Indicates the version of the EFI device driver. Legal Values Not Applicable Default Value Not Applicable Write Privilege Not Applicable License Required iDRAC Express or iDRAC Enterprise Dependency Not Applicable FC.FCDevice.FamilyVersion (Read Only) Table 1056. Details of FC.FCDevice.FamilyVersion attribute Description Indicates the firmware’s family version.
PAGE 467
Table 1058. Details of FC.FCTarget.BootScanSelection attribute (continued) Legal Values ● Disabled ● SpecifiedLUN ● FirstLUN ● FirstLUN0 ● FirstNOTLUN0 ● FabricDiscovered Default Value Disabled Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Dependency Not Applicable FC.FCTarget.FirstFCTargetLUN (Read or Write) Table 1059. Details of FC.FCTarget.FirstFCTargetLUN attribute Description Specifies the LUN (Logical Unit Number) of the first Fibre Channel boot target.
PAGE 468
Table 1061. Details of FC.FCTarget.FirstFCTargetWWPN attribute (continued) Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Dependency Not Applicable FC.FCTarget.SecondFCTargetWWPN (Read or Write) Table 1062. Details of FC.FCTarget.SecondFCTargetWWPN attribute Description Specifies the World Wide Port Name (WWPN) of the second Fibre Channel boot target.
PAGE 469
Table 1064. Details of FC.HBAConfig.FabricLoginTimeout attribute (continued) License Required iDRAC Express or iDRAC Enterprise Dependency Not Applicable FC.HBAConfig.FabricLoginRetryCount (Read or Write) Table 1065. Details of FC.HBAConfig.FabricLoginRetryCount attribute Description Sets the current SAN Fabric login retry count. Legal Values Not Applicable Default Value 3 Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Dependency Not Applicable FC.
PAGE 470
Table 1067. Details of FC.HBAConfig.HardZone attribute (continued) Dependency Not Applicable FC.HBAConfig.HardZoneAddress (Read or Write) Table 1068. Details of FC.HBAConfig.HardZoneAddress attribute Description Sets the Hard Zone address. Legal Values Not Applicable Default Value 0 Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Dependency Not Applicable FC.HBAConfig.LinkDownTimeout (Read or Write) Table 1069. Details of FC.HBAConfig.
PAGE 471
Table 1071. Details of FC.HBAConfig.PortDownRetryCount attribute (continued) Default Value Not Applicable Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Dependency Not Applicable FC.HBAConfig.PortDownTimeout (Read or Write) Table 1072. Details of FC.HBAConfig.PortDownTimeout attribute Description Sets the target port down time out.
PAGE 472
FC.PortConfig The objects in this group manage the Fiber Channel port configuration. FC.PortConfig.DeviceName (Read Only) Table 1075. Details of FC.PortConfig.DeviceName attribute Description Indicates the product name of the Fibre Channel host bus adapter. Legal Values Not Applicable Default Value Not Applicable Write Privilege Not Applicable License Required iDRAC Express or iDRAC Enterprise Dependency Not Applicable FC.PortConfig.FCDevice (Read Only) Table 1076. Details of FC.PortConfig.
PAGE 473
Table 1078. Details of FC.PortConfig.HBAConfig attribute (continued) Legal Values Not Applicable Default Value Not Applicable Write Privilege Not Applicable License Required iDRAC Express or iDRAC Enterprise Dependency Not Applicable FC.PortConfig.PortNumber (Read Only) Table 1079. Details of FC.PortConfig.PortNumber attribute Description Indicates the Fibre Channel Host Bus Adapter port number.
PAGE 474
Table 1081. Details of FC.PortConfig.VirtualWWN attribute (continued) Default Value Not Applicable Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Dependency Not Applicable FC.PortConfig.VirtualWWPN (Read or Write) Table 1082. Details of FC.PortConfig.VirtualWWPN attribute Description Indicates the virtual Fibre Channel World Wide Port Name of the port.
PAGE 475
NIC.ConfigureFormn The objects in this group manage. NIC.ConfigureFormn.BusDeviceFunction (Read Only) Table 1085. Details of NIC.ConfigureFormn.BusDeviceFunction attribute Description Indicates the value of the bus device function. Legal Values Not Applicable Default Value Not Applicable Write Privilege Not Applicable License Required iDRAC Express or iDRAC Enterprise Dependency Not Applicable NIC.ConfigureFormn.MacAddr (Read Only) Table 1086. Details of NIC.ConfigureFormn.
PAGE 476
Table 1088. Details of NIC.ConfigureFormn.IscsiMacAddr attribute (continued) Legal Values Not Applicable Default Value Not Applicable Write Privilege Not Applicable License Required iDRAC Express or iDRAC Enterprise Dependency Not Applicable NIC.ConfigureFormn.iScsiOffloadMode (Read or Write) Table 1089. Details of NIC.ConfigureFormn.iScsiOffloadMode attribute Description Enables or disables the iSCSI off load on the partition.
PAGE 477
Table 1091. Details of NIC.ConfigureFormn.NicMode attribute (continued) License Required iDRAC Express or iDRAC Enterprise Dependency Not Applicable NIC.ConfigureFormn.PCIDeviceID (Read Only) Table 1092. Details of NIC.ConfigureFormn.PCIDeviceID attribute Description Indicates the PCI Device ID of the partition. Legal Values Not Applicable Default Value Not Applicable Write Privilege Not Applicable License Required iDRAC Express or iDRAC Enterprise Dependency Not Applicable NIC.
PAGE 478
NIC_ConfigureFormn.VirtWWN (Read or Write) Table 1095. Details of attribute Description Sets the Fibre Channel World Wide Node Name identifier for partition FCoE. Legal Values Not Applicable Default Value 00:00:00:00:00:00:00:00 Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Dependency Not Applicable NIC_ConfigureFormn.VirtWWPN (Read or Write) Table 1096. Details of NIC_ConfigureFormn.
PAGE 479
Table 1098. Details of attribute (continued) License Required iDRAC Express or iDRAC Enterprise Dependency Not Applicable NIC_ConfigureFormn.VirtFIPMacAddr (Read or Write) Table 1099. Details of NIC_ConfigureFormn.VirtFIPMacAddr attribute Description Assigns the FIP-MAC address for partition FCoE. Legal Values Not Applicable Default Value 00:00:00:00:00:00 Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Dependency Not Applicable NIC.
PAGE 480
Table 1101. Details of NIC.DCBSettings.DCBExchangeProtocol attribute (continued) License Required iDRAC Express or iDRAC Enterprise Dependency None NIC.DCBSettings.EnhancedTransmissionSelection (Read Only) Table 1102. Details of NIC.DCBSettings.EnhancedTransmissionSelection attribute Description Indicates whether Enhanced Transmission Selection capability is supported.
PAGE 481
Table 1104. Details of NIC.DeviceLevelConfig.EVBModesSupport attribute (continued) ● VEPA ● PE ● Multichannel Default Value Not Applicable Write Privilege Not Applicable License Required iDRAC Express or iDRAC Enterprise Dependency None NIC.DeviceLevelConfig.FlowControlSetting (Read or Write) Table 1105. Details of NIC.DeviceLevelConfig.FlowControlSetting attribute Description Configure type of Flow Control used.
PAGE 482
Legal Values None Default Value None Write Privilege None License Required iDRAC Express or iDRAC Enterprise Dependency Not applicable NIC.DeviceLevelConfig.SRIOVSupport (Read Only) Table 1107. Details of NIC.DeviceLevelConfig.SRIOVSupport attribute Description Indicates whether SR-IOV capability is supported. Legal Values ● Available ● Unavailable Default Value Not Applicable Write Privilege Not Applicable License Required iDRAC Express or iDRAC Enterprise Dependency` None NIC.
PAGE 483
NIC.DeviceLevelConfig.VirtualizationMode (Read or Write) Table 1108. Details of NIC.DeviceLevelConfig.VirtualizationMode attribute Description Specifies the type of virtualization used by the controller on all ports.
PAGE 484
Table 1110. Details of NIC.FCOECapabilities.MaxFrameSize attribute (continued) License Required iDRAC Express or iDRAC Enterprise Dependency None NIC.FCOECapabilities.MaxIOsPerSession (Read Only) Table 1111. Details of NIC.FCOECapabilities.MaxIOsPerSession attribute Description Indicates the maximum number of IOs supported per session. Legal Values None Default Value Not Applicable Write Privilege Not Applicable License Required iDRAC Express or iDRAC Enterprise Dependency None NIC.
PAGE 485
NIC.FCOECapabilities.MaxNumberLogins (Read Only) Table 1114. Details of NIC.FCOECapabilities.MaxNumberLogins attribute Description Indicates the maximum number of logins supported per port. Legal Values None Default Value Not Applicable Write Privilege Not Applicable License Required iDRAC Express or iDRAC Enterprise Dependency None NIC.FCOECapabilities.MaxNumberOfFCTargets (Read Only) Table 1115. Details of NIC.FCOECapabilities.
PAGE 486
Table 1117. Details of NIC.FCOECapabilities.MTUReconfigurationSupport attribute (continued) Legal Values ● Available ● Unavailable Default Value Not Applicable Write Privilege Not Applicable License Required iDRAC Express or iDRAC Enterprise Dependency None NIC.FCoEConfiguration The following section provides information about the objects in the NIC.FCoEConfiguration group. NIC.FCoEConfiguration.ConnectFirstFCoETarget (Read or Write) Table 1118. Details of NIC.FCoEConfiguration.
PAGE 487
NIC.FCoEConfiguration.BootOrderSecondFCoETarget (Read or Write) Table 1120. Details of NIC.FCoEConfiguration.BootOrderSecondFCoETarget attribute Description Specifies the port's second defined target in the FCoE boot. Legal Values Not Applicable Default Value 0 Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Dependency Not Applicable NIC.FCoEConfiguration.BootOrderThirdFCoETarget (Read or Write) Table 1121. Details of NIC.FCoEConfiguration.
PAGE 488
Table 1123. Details of NIC.FCoEConfiguration.FirstFCoEBootTargetLUN attribute (continued) Legal Values None Default Value Not Applicable Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Dependency Enable FCoEConfiguration.ConnectFirstFCoETarget NIC.FCoEConfiguration.FirstFCoEFCFVLANID (Read or Write) Table 1124. Details of NIC.FCoEConfiguration.FirstFCoEFCFVLANID attribute Description VLAN ID uses the first FC storage target to connect.
PAGE 489
Table 1126. Details of NIC.FCoEConfiguration.MTUParams attribute (continued) Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Dependency None NIC.FCoEGenParams The following section provides information about the objects in the NIC.FCoEGenParams group. NIC.FCoEGenParams.FCoEBootScanSelection (Read or Write) Table 1127. Details of NIC.FCoEGenParams.
PAGE 490
NIC.FCoEGenParams.FCoEFirstHddTarget (Read or Write) Table 1129. Details of NIC.FCoEGenParams.FCoEFirstHddTarget attribute Description Specifies whether the FCoE target is represented as the first HDD to the system. Legal Values ● Enabled ● Disabled Default Value Disabled Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Dependency None NIC.FCoEGenParams.FCoELnkUpDelayTime (Read or Write) Table 1130. Details of NIC.FCoEGenParams.
PAGE 491
NIC.FCoEGenParams.FCoETgtBoot (Read or Write) Table 1132. Details of NIC.FCoEGenParams.FCoETgtBoot attribute Description Enables the FCoE initiator to start system to the FCoE target. Legal Values ● Enabled ● Disabled Default Value Disabled Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Dependency None NIC.FrmwImgMenu The following section provides information about the objects in the NIC.FrmwImgMenu group. NIC.FrmwImgMenu.
PAGE 492
NIC.FrmwImgMenu.FamilyVersion (Read Only) Table 1135. Details of IC.FrmwImgMenu.FamilyVersion attribute Description Indicates the firmware family version information. Legal Values String of up to 8 ASCII characters Default Value Not Applicable Write Privilege Not Applicable License Required iDRAC Express or iDRAC Enterprise Dependency None NIC.GlobalBandwidthAllocation The following section provides information about the objects in the NIC.GlobalBandwidthAllocation group. NIC.
PAGE 493
NIC.IscsiFirstTgtParams The following section provides information about the objects in the NIC.IscsiFirstTgtParams group. NIC.IscsiFirstTgtParams.AddressingMode (Read or Write) Table 1138. Details of NIC.IscsiFirstTgtParams.AddressingMode attribute Description Enables or disables the connection to the first iSCSI target. Legal Values ● Enabled ● Disabled Default Value Disabled Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Dependency Not Applicable NIC.
PAGE 494
NIC.IscsiFirstTgtParams.FirstTgtChapId (Read or Write) Table 1141. Details of NIC.IscsiFirstTgtParams.FirstTgtChapId attribute Description Set the first iSCSI storage target Challenge-Handshake Authentication Protocol (CHAP) ID. Legal Values String of up to 128 ASCII characters Default Value Not Applicable Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Dependency Not Available if VndrConfigGroup.iSCSIBootSupport is Unavailable. NIC.IscsiFirstTgtParams.
PAGE 495
Table 1144. Details of NIC.IscsiFirstTgtParams.FirstTgtIpVer attribute (continued) Legal Values ● IPv4 ● IPv6 Default Value IPv4 Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Dependency Not Applicable NIC.IscsiFirstTgtParams.FirstTgtIscsiName (Read or Write) Table 1145. Details of NIC.IscsiFirstTgtParams.FirstTgtIscsiName attribute Description Set the iSCSI Qualified Name (IQN) of the first iSCSI storage target.
PAGE 496
NIC.IscsiGenParams.ChapAuthEnable (Read or Write) Table 1147. Details of NIC.IscsiGenParams.ChapAuthEnable attribute Description To use CHAP authentication when connecting to the iSCSI target, enable or disable the ability of the initiator. Legal Values ● Enabled ● Disabled Default Value Disabled Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Dependency Not available if VndrConfigGroup.iSCSIBootSupport is unavailable. NIC.IscsiGenParams.
PAGE 497
NIC.IscsiGenParams.FirstHddTarget (Read or Write) Table 1150. Details of NIC.IscsiGenParams.FirstHddTarget attribute Description Enables or disables to check if the iSCSI target appears as the first hard disk drive (HDD) in the system. Legal Values ● Enabled ● Disabled Default Value Disabled Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Dependency Not Available if VndrConfigGroup.iSCSIBootSupport is Unavailable. NIC.IscsiGenParams.
PAGE 498
NIC.IscsiGenParams.IscsiTgtBoot (Read or Write) Table 1153. Details of NIC.IscsiGenParams.IscsiTgtBoot attribute Description Specifies whether or not the iSCSI initiator will boot to the specified iSCSI target after connection. Legal Values ● Enabled ● Disabled ● OneTimeDisabled Default Value Disabled Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Dependency Not Applicable NIC.IscsiGenParams.IscsiViaDHCP (Read or Write) Table 1154. Details of NIC.
PAGE 499
Table 1156. Details of NIC.IscsiGenParams.IscsiVLanMode attribute (continued) Legal Values ● Enabled ● Disabled Default Value Disabled Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Dependency Not Applicable NIC.IscsiGenParams.LnkUpDelayTime (Read or Write) Table 1157. Details of NIC.IscsiGenParams.LnkUpDelayTime attribute Description Set the time to allow for link to establish before driver initialization.
PAGE 500
Table 1159. Details of NIC.IscsiGenParams.TcpIpViaDHCP attribute (continued) Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Dependency Not Available if IscsiGenParams.IpVer is set to 'IPv6' and VndrConfigGroup.iSCSIBootSupport is Unavailable. NIC.IscsiGenParams.TcpTimestmp (Read or Write) Table 1160. Details of NIC.IscsiGenParams.TcpTimestmp attribute Description Enables or disables use of TCP timestamps in network packets as defined in RFC 1323.
PAGE 501
Table 1162. Details of NIC.IscsiInitiatorParams.IscsiInitiatorChapId attribute (continued) Legal Values String of up to 128 characters Default Value Not Applicable Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Dependency Not available if VndrConfigGroup.iSCSIBootSupport is unavailable. NIC.IscsiInitiatorParams.IscsiInitiatorChapPwd (Read or Write) Table 1163. Details of NIC.IscsiInitiatorParams.
PAGE 502
Table 1165. Details of NIC.IscsiInitiatorParams.IscsiInitiatorIpAddr attribute (continued) License Required iDRAC Express or iDRAC Enterprise Dependency Not available if VndrConfigGroup.iSCSIBootSupport is unavailable. NIC.IscsiInitiatorParams.IscsiInitiatorName (Read or Write) Table 1166. Details of NIC.IscsiInitiatorParams.IscsiInitiatorName attribute Description Specifies the initiator iSCSI Qualified Name (IQN).
PAGE 503
NIC.IscsiInitiatorParams.IscsiInitiatorSubnet (Read or Write) Table 1169. Details of NIC.IscsiInitiatorParams.IscsiInitiatorSubnet attribute Description Specifies the IPv4 Subnet Mask of the iSCSI initiator. Legal Values String of 7–15 characters (IPv4 Subnet) Default Value Not Applicable Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Dependency Not available if VndrConfigGroup.iSCSIBootSupport is unavailable. NIC.IscsiInitiatorParams.
PAGE 504
NIC.IscsiSecondaryDeviceParams.UseIndTgtName (Read or Write) Table 1172. Details of NIC.IscsiSecondaryDeviceParams.UseIndTgtName attribute Description Specifies whether to use Independent Target Name when multipath I/O is enabled. Legal Values ● Enabled ● Disabled Default Value Disabled Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Dependency Not available if VndrConfigGroup.iSCSIBootSupport is unavailable. NIC.IscsiSecondaryDeviceParams.
PAGE 505
NIC.IscsiSecondTgtParams.SecondTgtBootLun (Read or Write) Table 1175. Details of NIC.IscsiSecondTgtParams.SecondTgtBootLun attribute Description Specifies the second iSCSI storage target boot Logical Unit Number (LUN). Legal Values Values: 0–18446744073709551615 Default Value Not Applicable Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Dependency Not available if VndrConfigGroup.iSCSIBootSupport is unavailable. NIC.IscsiSecondTgtParams.
PAGE 506
Table 1178. Details of NIC.IscsiSecondTgtParams.SecondTgtIpAddress attribute (continued) Legal Values String of 2-39 characters (Ipv4 or Ipv6 address) Default Value Not Applicable Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Dependency Not available if VndrConfigGroup.iSCSIBootSupport is unavailable. NIC.IscsiSecondTgtParams.SecondTgtIpVer (Read or Write) Table 1179. Details of NIC.IscsiSecondTgtParams.
PAGE 507
Table 1181. Details of NIC.IscsiSecondTgtParams.SecondTgtTcpPort attribute (continued) Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Dependency Not available if VndrConfigGroup.iSCSIBootSupport is unavailable. NIC.NICConfig To configure the NICConfig properties, use the objects in this group. NIC.NICConfig.BannerMessageTimeout (Read or Write) Table 1182. Details of NIC.NICConfig.
PAGE 508
Table 1184. Details of NIC.NICConfig.BootRetryCnt attribute (continued) ● 3Retries ● 4Retries ● 5Retries ● 6Retries ● IndefiniteRetries Default Value NoRetry Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Dependency Not Applicable NIC.NICConfig.BootStrapType (Read or Write) Table 1185. Details of NIC.NICConfig.BootStrapType attribute Description Specifies the boot strap method used to start the operating system.
PAGE 509
NIC.NICConfig.LegacyBootProto (Read or Write) Table 1187. Details of NIC.NICConfig.LegacyBootProto attribute Description Select a non-UEFI network start protocol. Legal Values ● ● ● ● ● ● Default Value None Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Dependency None PXE iSCSI FCoE NONE iSCSIPrimary iSCSI Secondary NIC.NICConfig.LnkSpeed (Read or Write) Table 1188. Details of NIC.NICConfig.
PAGE 510
NIC.NICConfig.VLanId (Read or Write) Table 1190. Details of NIC.NICConfig.VLanId attribute Description Specifies the ID (tag) for the VLAN Mode. Legal Values Values: 1–4095 Default Value Not Applicable Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Dependency VLanMode must be enabled. NIC.NICConfig.VLanMode (Read or Write) Table 1191. Details of NIC.NICConfig.
PAGE 511
Table 1193. Details of NIC.NICConfig.WakeOnLanLnkSpeed attribute (continued) Legal Values ● ● ● ● ● Default Value AutoNeg Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Dependency None AutoNeg 10 Mbps Half 10 Mbps Full 100 Mbps Half 100 Mbps Full NIC.NICPartitioningConfig To configure the NICPartitioning properties, use the objects in this group. NIC.NICPartitioningConfig.NicPartitioning (Read or Write) Table 1194. Details of NIC.NICPartitioningConfig.
PAGE 512
NIC.NICPartitioningConfig.ConfigureFormn (Read Only) Table 1196. Details of NIC.NICPartitioningConfig.ConfigureFormn attribute Description Configures the partition functionality and display the assigned address. Legal Values Not Applicable Default Value Not Applicable Write Privilege Not Applicable License Required iDRAC Express or iDRAC Enterprise Dependency Not Applicable NIC.NICPartitioningConfig.NumberPCIEFunctionsEnabled (Read Only) Table 1197. Details of NIC.NICPartitioningConfig.
PAGE 513
NIC.VndrConfigGroup.BusDeviceFunction (Read Only) Table 1199. Details of NIC.VndrConfigGroup.BusDeviceFunction attribute Description Indicates the BIOS assigned PCIe. Legal Values String of up to 8 characters Default Value Not Applicable Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Dependency None NIC.VndrConfigGroup.BlnkLeds (Read or Write) Table 1200. Details of NIC.VndrConfigGroup.
PAGE 514
Table 1202. Details of NIC.VndrConfigGroup.EnergyEfficientEthernet attribute (continued) Default Value Not Applicable Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Dependency None NIC.VndrConfigGroup.DCBXSupport (Read Only) Table 1203. Details of NIC.VndrConfigGroup.DCBXSupport attribute Description Indicates whether Data Center Bridging (DCB) capability is supported.
PAGE 515
NIC.VndrConfigGroup.FCoEOffloadMode (Read or Write) Table 1206. Details of NIC.VndrConfigGroup.FCoEOffloadMode attribute Description Enables or disables FCoE personality on the port. Legal Values ● Enabled ● Disabled Default Value Disabled Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Dependency None NIC.VndrConfigGroup.FCoEOffloadSupport (Read Only) Table 1207. Details of NIC.VndrConfigGroup.
PAGE 516
Table 1209. Details of NIC.VndrConfigGroup.FIPMacAddr attribute (continued) Legal Values String of up to 17 characters Default Value Not Applicable Write Privilege Not Applicable License Required iDRAC Express or iDRAC Enterprise Dependency None NIC.VndrConfigGroup.FlexAddressing (Read Only) Table 1210. Details of NIC.VndrConfigGroup.FlexAddressing attribute Description Indicates whether Dell FlexAddressing feature is supported.
PAGE 517
Table 1212. Details of NIC.VndrConfigGroup.ISCSIMacAddr attribute (continued) Dependency None NIC.VndrConfigGroup.iSCSIOffloadMode (Read or Write) Table 1213. Details of NIC.VndrConfigGroup.iSCSIOffloadMode attribute Description Enables or disables iSCSI offload personality on the port. Legal Values ● Enabled ● Disabled Default Value Disabled Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Dependency None NIC.VndrConfigGroup.
PAGE 518
NIC.VndrConfigGroup.MacAddr (Read Only) Table 1216. Details of NIC.VndrConfigGroup.MacAddr attribute Description Indicates the permanent MAC address assigned during manufacturing. Legal Values String of up to 17 characters Default Value Not Applicable Write Privilege Not Applicable License Required iDRAC Express or iDRAC Enterprise Dependency None NIC.VndrConfigGroup.NicMode (Read or Write) Table 1217. Details of NIC.VndrConfigGroup.
PAGE 519
Table 1219. Details of NIC.VndrConfigGroup.NWManagementPassThrough attribute (continued) Default Value Not Applicable Write Privilege Not Applicable License Required iDRAC Express or iDRAC Enterprise Dependency None NIC.VndrConfigGroup.OnChipThermalSensor (Read Only) Table 1220. Details of NIC.VndrConfigGroup.OnChipThermalSensor attribute Description Indicates whether an on-chip thermal sensor is available.
PAGE 520
Table 1222. Details of NIC.VndrConfigGroup.PCIDeviceID attribute (continued) Dependency None NIC.VndrConfigGroup.PXEBootSupport (Read Only) Table 1223. Details of NIC.VndrConfigGroup.PXEBootSupport attribute Description Indicates whether PXE Boot capability is supported. Legal Values None Default Value Not Applicable Write Privilege Not Applicable License Required iDRAC Express or iDRAC Enterprise Dependency None NIC.VndrConfigGroup.RemotePHY (Read Only) Table 1224. Details of NIC.
PAGE 521
NIC.VndrConfigGroup.TOESupport (Read Only) Table 1226. Details of NIC.VndrConfigGroup.TOESupport attribute Description Indicates whether TCP/IP Offload Engine capability is supported. Legal Values None Default Value Not Applicable Write Privilege Not Applicable License Required iDRAC Express or iDRAC Enterprise Dependency None NIC.VndrConfigGroup.TXBandwidthControlMaximum (Read Only) Table 1227. Details of NIC.VndrConfigGroup.
PAGE 522
Table 1229. Details of NIC.VndrConfigGroup.TXFlowControl attribute (continued) Write Privilege Not Applicable License Required iDRAC Express or iDRAC Enterprise Dependency None NIC.VndrConfigGroup.VirtFIPMacAddr (Read or Write) Table 1230. Details of NIC.VndrConfigGroup.VirtFIPMacAddr attribute Description Programmatically assignable FIP-MAC address for FCoE. Programmatic write for support of I/O Identity feature.
PAGE 523
Table 1232. Details of NIC.VndrConfigGroup.VirtMacAddr attribute (continued) Dependency None NIC.VndrConfigGroup.VirtualLinkControl (Read or Write) Table 1233. Details of NIC.VndrConfigGroup.VirtualLinkControl attribute Description Indicates whether Virtual Link Control capability is supported. Legal Values None Default Value Not Applicable Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Dependency None NIC.VndrConfigGroup.VirtWWN (Read or Write) Table 1234.
PAGE 524
NIC.VndrConfigGroup.WWN (Read Only) Table 1236. Details of NIC.VndrConfigGroup.WWN attribute Description Fibre Channel World Wide Node Name identifier for FCoE. Legal Values String of up to 23 characters Default Value Not Applicable Write Privilege Not Applicable License Required iDRAC Express or iDRAC Enterprise Dependency None NIC.VndrConfigGroup.WWPN (Read Only) Table 1237. Details of NIC.VndrConfigGroup.WWPN attribute Description Fibre Channel World Wide Port Name identifier for FCoE.
PAGE 525
Default Value None Write Privilege None License Required iDRAC Express or iDRAC Enterprise Dependency Not applicable NIC.VndrConfigPage.ChipMdl (Read Only) Description This attribute consists of the concatenation of 2 different elements, a vendor-defined silicon marketing name and the silicon revision information as specified in PCI configuration space, separated by space. For example: R720 B0.
PAGE 526
License Required iDRAC Express or iDRAC Enterprise Dependency Not applicable NIC.VndrConfigPage.FlexAddressing (Read Only) Description Indicates whether the Dell FlexAddressing feature is supported. Legal Values ● Available ● Unavailable Default Value None Write Privilege None License Required iDRAC Express or iDRAC Enterprise Dependency Not applicable NIC.VndrConfigPage.iSCSIBootSupport (Read Only) Description Indicates whether iSCSI Boot is supported.
PAGE 527
Dependency Not applicable NIC.VndrConfigPage.iSCSIOffloadSupport (Read Only) Description Indicates whether the iSCSI Offload capability is supported. Legal Values ● Available ● Unavailable Default Value None Write Privilege None License Required iDRAC Express or iDRAC Enterprise Dependency Not applicable NIC.VndrConfigPage.LinkStatus (Read Only) Description Physical link status of the network port as reported by the controller.
PAGE 528
NIC.VndrConfigPage.PCIDeviceID (Read Only) Description PCI Device ID reported by the controller when operating in non-NPar mode only. The value of the attribute is undefined for controllers operating in NPar mode that change their device IDs or support multiple PCI Device IDs at the partition level. Legal Values String of up to 4 characters Default Value None Write Privilege None License Required iDRAC Express or iDRAC Enterprise Dependency Not applicable NIC.VndrConfigPage.
PAGE 529
NIC.VndrConfigPage.VirtMacAddr (Read or Write) Description Programmatically assignable MAC address. Programmatic write for support of I/O Identity feature. The supported method of reverting to the permanent MAC address is by writing 0's to the virtual MAC. If the virtual address has not been set or if it has been cleared by the defined method, its value shall be returned as 0's. If supported, the current address value should be readable at all times, irrespective of feature enablement.
PAGE 530
Dependency Not applicable NIC.VndrConfigPage.WWPN (Read Only) Description Fibre Channel World Wide Port Name identifier for FCoE Legal Values String of upto 23 characters Default Value Not Applicable Write Privilege None License Required iDRAC Express or iDRAC Enterprise Dependency Not applicable Storage.Controller The objects in this group manage storage controller attributes. This group is indexed. The following sections provide information about the objects in this group. Storage.Controller.
PAGE 531
Storage.Controller.CheckConsistencyMode (Read or Write) Table 1240. Details of Storage.Controller.CheckConsistencyMode attribute Description Check Consistency feature is used to verify the accuracy of the redundant (parity) information. Legal Values ● Normal ● Stop On Error Default value Normal Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Dependency None Storage.Controller.CheckConsistencyRate (Read or Write) Table 1241. Details of Storage.Controller.
PAGE 532
Table 1243. Details of Storage.Controller.CopybackMode attribute (continued) ● ON with SMART ● Off Default value On Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Dependency None Storage.Controller.CurrentControllerMode (Read Only) Table 1244. Details of Storage.Controller.CurrentControllerMode attribute Description Indicates the current personality mode of controllers.
PAGE 533
Table 1246. Details of Storage.Controller.PatrolReadMode attribute (continued) License Required iDRAC Express or iDRAC Enterprise Dependency None Storage.Controller.PatrolReadRate (Read or Write) Table 1247. Details of Storage.Controller.PatrolReadRate attribute Description The Patrol Read Rate is the percentage of the system's resources dedicated to perform Patrol Read.
PAGE 534
Storage.Controller.PossibleloadBalancedMode (Read or Write) Table 1250. Details of Storage.Controller.PossibleloadBalancedMode attribute Description This attribute represents the ability to automatically use both controller ports connected to the same enclosure to route I/O requests. Legal Values ● Automatic ● Disabled Default value Automatic Write Privilege Server Control License Required iDRAC Express or iDRAC Enterprise Dependency None Storage.Controller.
PAGE 535
Table 1253. Details of Storage.Controller.RequestedControllerMode attribute (continued) ● HBA ● Not Supported Default value Not Applicable Write Privilege Server Control License Required RACADM Dependency None Storage.Controller.SupportControllerBootMode (Read Only) Table 1254. Details of Storage.Controller.SupportControllerBootMode attribute Description This is read only attribute. This property indicates if this controller supports setting of controller boot mode.
PAGE 536
Table 1256. Details of Storage.Controller.SupportRAID10UnevenSpans attribute (continued) License Required iDRAC Express or iDRAC Enterprise Dependency None Storage.Controller.T10PICapability (Read Only) Table 1257. Details of Storage.Controller.T10PICapability attribute Description This is a read-only attribute. This property indicates if this controller supports T10 PI.
PAGE 537
Table 1259. Details of Storage.enclosure.BackplaneRequestedMode attribute (continued) ● ● ● ● ● ● SplitMode–4:20 SplitMode–8:16 SplitMode–16:8 SplitMode–20:4 Not Applicable None Default Value UnifiedMode Write Privilege Server Control License Required RACADM Dependency Backplane must support. Storage.enclosure.BackplaneType (Read Only) Table 1260. Details of Storage.enclosure.BackplaneType attribute Description Indicates whether or not the backplane is shared.
PAGE 538
Storage.PhysicalDisk.MaxCapableSpeed (Read Only) Table 1262. Details of Storage.PhysicalDisk.MaxCapableSpeed attribute Description This is a read-only attribute. The property represents the data transfer speed that the disk is capable of. Legal Values ● ● ● ● ● Default value Not Applicable Write Privilege Not Applicable License Required iDRAC Express or iDRAC Enterprise Dependency None Unknown 1.5GBPS 3GBPS 6GBPS 12GBPS Storage.PhysicalDisk.RaidNominalMediumRotationRate (Read Only) Table 1263.
PAGE 539
Storage.VirtualDisk.BlockSizeInBytes (Read Only) Table 1265. Details of Storage.VirtualDisk.BlockSizeInBytes attribute Description This is a read-only attribute. This property indicates the logical block size of the physical drive that this virtual disk belongs to. Legal Values Values: 512 or 4096 Default value Not Applicable Write Privilege Not Applicable License Required iDRAC Express or iDRAC Enterprise Dependency None Storage.VirtualDisk.DiskCachePolicy (Read or Write) Table 1266.
PAGE 540
Table 1267. Details of the Storage.VirtualDisk.ReadPolicy attribute (continued) Dependency None Storage.VirtualDisk.T10PIStatus (Read or Write) Table 1268. Details of the Storage.VirtualDisk.T10PIStatus attribute Description This property indicates if T10 PI is enabled or disabled on this virtual disk. NOTE: Can be disabled only if the current value for this object is enabled.
PAGE 541
A Deprecated and New Subcommands Table 1270.
PAGE 542
B Legacy and New Groups and Objects Table 1271. Details of legacy groups and objects Legacy Groups and Objects New Groups and Objects idRacInfo iDRAC.Info idRacType Type idRacProductInfo Product idRacDescriptionInfo Description idRacVersionInfo Version idRacBuildInfo Build idRacName Name cfgActiveDirectory iDRAC.
PAGE 543
Table 1271. Details of legacy groups and objects (continued) Legacy Groups and Objects New Groups and Objects cfgADGcRootDomain GCRootDomain cfgLanNetworking iDRAC.Nic cfgNicEnable Enable cfgNicMacAddress MACAddress cfgDNSRacName DNSRacName cfgNicSelection Selection cfgNicFailoverNetwork Failover cfgDNSDomainName DNSDomainName cfgDNSDomainNameFromDHCP DNSRacName cfgDNSRegisterRac DNSRegister cfgNicVLanEnable VLanEnable cfgNicVLanID VLanID cfgNicVLanPriority VLanPriority iDRAC.
PAGE 544
Table 1271.
PAGE 545
Table 1271. Details of legacy groups and objects (continued) Legacy Groups and Objects New Groups and Objects cfgServerPowerLastHourAvg Avg.LastHour cfgServerPowerLastDayAvg Avg.LastDay cfgServerPowerLastWeekAvg Avg.LastWeek cfgServerPowerLastHourMinPower Min.LastHour cfgServerPowerLastHourMinTime Min.LastHour.Timestamp cfgServerPowerLastHourMaxPower Max.LastHour cfgServerPowerLastHourMaxTime Max.LastHour.Timestamp cfgServerPowerLastDayMinPower Min.
PAGE 546
Table 1271. Details of legacy groups and objects (continued) Legacy Groups and Objects New Groups and Objects cfgServerPowerSupplyOnlineStatus Status cfgServerPowerSupplyFwVer FwVer cfgServerPowerSupplyCurrentDraw CurrentDraw cfgServerPowerSupplyType Type cfgServerPowerBusMonitoring PMBusMonitoring cfgUserAdmin iDRAC.
PAGE 547
Table 1271. Details of legacy groups and objects (continued) Legacy Groups and Objects New Groups and Objects cfgEmailAlertAddress Address cfgEmailAlertCustomMsg CustomMsg cfgSessionManagement cfgSsnMgtTelnetIdleTimeout iDRAC.Telnet Enable Port Timeout cfgSsnMgtSshIdleTimeout iDRAC.SSH Enable Port Timeout cfgSsnMgtRacadmTimeout iDRAC.Racadm Enable Timeout cfgSsnMgtConsRedirMaxSessions iDRAC.
PAGE 548
Table 1271. Details of legacy groups and objects (continued) Legacy Groups and Objects New Groups and Objects [cfgSerial] iDRAC.Serial cfgSerialBaudRate BaudRate cfgSerialConsoleEnable Enable cfgSerialConsoleIdleTimeout IdleTimeout cfgSerialConsoleNoAuth NoAuth cfgSerialConsoleCommand Command cfgSerialHistorySize HistorySize iDRAC.SerialRedirection cfgSerialConsoleQuitKey QuitKey cfgSerialCom2RedirEnable Enable cfgSerialTelnetEnable iDRAC.Telnet cfgSerialSshEnable iDRAC.
PAGE 549
Table 1271. Details of legacy groups and objects (continued) Legacy Groups and Objects New Groups and Objects cfgRacTuneConRedirPort=5900 iDRAC.VirtualConsole cfgRacTuneConRedirEncryptEnable=1 iDRAC.VirtualConsole cfgRacTuneLocalServerVideo=1 iDRAC.VirtualConsole iDRAC.IPBlocking cfgRacTuneIpRangeEnable=0 RangeEnable cfgRacTuneIpRangeAddr=192.168.1.1 RangeAddr cfgRacTuneIpRangeMask=255.255.255.0 RangeMask iDRAC.
PAGE 550
Table 1271. Details of legacy groups and objects (continued) Legacy Groups and Objects New Groups and Objects cfgVirMediaAttached Attached cfgVirtualBootOnce BootOnce cfgVirMediaFloppyEmulation FloppyEmulation cfgLDAP iDRAC.
PAGE 551
Table 1271. Details of legacy groups and objects (continued) Legacy Groups and Objects New Groups and Objects cfgIpmiSerialLineEdit LineEdit cfgIpmiSerialDeleteControl DeleteControl cfgIpmiSerialEchoControl EchoControl cfgIpmiSerialHandshakeControl HandshakeControl cfgIpmiSerialNewLineSequence NewLineSeq cfgIpmiSerialInputNewLineSequence InputNewLineSeq cfgIpmiSol iDRAC.
PAGE 552
Table 1271. Details of legacy groups and objects (continued) Legacy Groups and Objects New Groups and Objects cfgVFlashSDLicensed Licensed cfgVFlashSDAvailableSize AvailableSize cfgVFlashSDHealth Health cfgVFlashSDEnable Enable cfgVFlashSDWriteProtect WriteProtect cfgVFlashSDInitialized Initialized cfgVFlashPartition iDRAC.
PAGE 553
Table 1272. Details of cfgSSADRoleGroupPrivilege (continued) Default Table 1273.