Inspiron 15 5000 Gaming Service-Handbuch Computer-Modell: Inspiron 15-5577 Vorschriftenmodell: P57F Vorschriftentyp: P57F003
Anmerkungen, Vorsichtshinweise und Warnungen ANMERKUNG: Eine ANMERKUNG macht auf wichtige Informationen aufmerksam, mit denen Sie Ihr Produkt besser einsetzen können. VORSICHT: Ein VORSICHTSHINWEIS macht darauf aufmerksam, dass bei Nichtbefolgung von Anweisungen eine Beschädigung der Hardware oder ein Verlust von Daten droht, und zeigt auf, wie derartige Probleme vermieden werden können.
Inhaltsverzeichnis Vor der Arbeit an Komponenten im Innern des Computers................................................................... 10 Bevor Sie beginnen: ................................................................................ 10 Sicherheitshinweise................................................................................. 10 Empfohlene Werkzeuge........................................................................... 12 Schraubenliste................................................
Wiedereinbauen der Speichermodule........................... 24 Vorgehensweise...................................................................................... 24 Voraussetzungen nach der Arbeit am Computer..................................... 25 Entfernen des Festplattenlaufwerks............................ 26 Voraussetzungen.....................................................................................26 Vorgehensweise............................................................................
Wiedereinbauen der Tastatur........................................ 41 Vorgehensweise....................................................................................... 41 Voraussetzungen nach der Arbeit am Computer......................................41 Falten der Tastaturkabel...........................................................................41 Entfernen der Handballenstütze.................................. 45 Voraussetzungen..................................................................
Einbauen der Lüfter...................................................... 61 Vorgehensweise.......................................................................................61 Voraussetzungen nach der Arbeit am Computer......................................61 Entfernen des Netzadapteranschlusses....................... 62 Voraussetzungen.....................................................................................62 Vorgehensweise..................................................................
Wiedereinbauen des Kühlkörpers..................................77 Vorgehensweise.......................................................................................77 Voraussetzungen nach der Arbeit am Computer..................................... 77 Entfernen der Lautsprecher......................................... 79 Voraussetzungen.....................................................................................79 Vorgehensweise....................................................................
Wiedereinbauen der Bildschirmblende......................... 94 Vorgehensweise...................................................................................... 94 Voraussetzungen nach der Arbeit am Computer..................................... 94 Entfernen des Bildschirms........................................... 95 Voraussetzungen.................................................................................... 95 Vorgehensweise......................................................................
Wiedereinbauen des Bildschirmscharniers und der Halterungsbaugruppe................................................. 109 Vorgehensweise.....................................................................................109 Voraussetzungen nach der Arbeit am Computer................................... 109 Entfernen der hinteren Bildschirmabdeckung und der Antennenbaugruppe.............................................. 111 Voraussetzungen......................................................................
Vor der Arbeit an Komponenten im Innern des Computers ANMERKUNG: Die Abbildungen in diesem Dokument können von Ihrem Computer abweichen, je nach der von Ihnen bestellten Konfiguration. Bevor Sie beginnen: 1 Speichern und schließen Sie alle geöffneten Dateien und beenden Sie alle geöffneten Programme. 2 Fahren Sie den Computer herunter. Klicken Sie aufStart → down (Herunterfahren).
WARNUNG: Trennen Sie den Computer vom Netz, bevor Sie die Computerabdeckung oder Verkleidungselemente entfernen. Bringen Sie nach Abschluss der Arbeiten innerhalb des Computers wieder alle Abdeckungen, Verkleidungselemente und Schrauben an, bevor Sie das Gerät erneut an das Stromnetz anschließen. VORSICHT: Achten Sie auf eine ebene und saubere Arbeitsfläche, um Schäden am Computer zu vermeiden.
Empfohlene Werkzeuge Für die in diesem Dokument beschriebenen Arbeitsschritte können die folgenden Werkzeuge erforderlich sein: • Kreuzschlitzschraubenzieher • Torxschraubendreher Nr. 8 (T8) • Kunststoffstift Schraubenliste Die folgende Tabelle enthält die Liste der Schrauben, die zur Befestigung verschiedener Komponenten verwendet werden. Tabelle 1.
Komponente Zur Befestigung von Schraubentyp Menge M2x5 4 Hintere M2x3 Bildschirmabdeck ung 4 Halterungsbaugr Hintere M2x3 uppe Bildschirmabdeck ung 2 Bildschirm 4 Bildschirmbaugr Computersockel uppe Bildschirmschar niere Hintere M2x3 Bildschirmabdeck ung Abbildung Schraube 13
Nach der Arbeit an Komponenten im Inneren des Computers VORSICHT: Im Inneren des Computers vergessene oder lose Schrauben können den Computer erheblich beschädigen. 1 Bringen Sie alle Schrauben wieder an und stellen Sie sicher, dass sich im Inneren des Computers keine losen Schrauben mehr befinden. 2 Schließen Sie alle externen Geräte, Peripheriegeräte oder Kabel wieder an, die Sie vor dem Arbeiten an Ihrem Computer entfernt haben.
Entfernen der Bodenabdeckung WARNUNG: Bevor Sie Arbeiten im Inneren des Computers ausführen, lesen Sie zunächst die im Lieferumfang des Computers enthaltenen Sicherheitshinweise und befolgen Sie die Anweisungen unter Bevor Sie im Inneren Ihres Computers arbeiten. Befolgen Sie nach Arbeiten im Inneren des Computers die Anweisungen unter. nach Abschluss der Arbeiten im Inneren Ihres Computers.
4 16 Trennen Sie das Batteriekabel von der Systemplatine.
Wiedereinbauen der Bodenabdeckung WARNUNG: Bevor Sie Arbeiten im Inneren des Computers ausführen, lesen Sie zunächst die im Lieferumfang des Computers enthaltenen Sicherheitshinweise und befolgen Sie die Anweisungen unter Bevor Sie im Inneren Ihres Computers arbeiten. Befolgen Sie nach Arbeiten im Inneren des Computers die Anweisungen unter. nach Abschluss der Arbeiten im Inneren Ihres Computers.
Entfernen des Akkus WARNUNG: Bevor Sie Arbeiten im Inneren des Computers ausführen, lesen Sie zunächst die im Lieferumfang des Computers enthaltenen Sicherheitshinweise und befolgen Sie die Anweisungen unter Bevor Sie im Inneren Ihres Computers arbeiten. Befolgen Sie nach Arbeiten im Inneren des Computers die Anweisungen unter. nach Abschluss der Arbeiten im Inneren Ihres Computers.
2 Entfernen Sie die fünf Schrauben (M2x5 T8), mit denen der Akku am Computersockel befestigt ist.
3 Heben Sie den Akku mithilfe der Zuglasche zusammen mit dem Kabel aus dem Computersockel heraus. 4 Drehen Sie den Computer um, öffnen Sie den Bildschirm und halten Sie den Betriebsschalter etwa fünf Sekunden lang gedrückt, um die Systemplatine zu erden.
Wiedereinbauen des Akkus WARNUNG: Bevor Sie Arbeiten im Inneren des Computers ausführen, lesen Sie zunächst die im Lieferumfang des Computers enthaltenen Sicherheitshinweise und befolgen Sie die Anweisungen unter Bevor Sie im Inneren Ihres Computers arbeiten. Befolgen Sie nach Arbeiten im Inneren des Computers die Anweisungen unter. nach Abschluss der Arbeiten im Inneren Ihres Computers.
Entfernen der Speichermodule WARNUNG: Bevor Sie Arbeiten im Inneren des Computers ausführen, lesen Sie zunächst die im Lieferumfang des Computers enthaltenen Sicherheitshinweise und befolgen Sie die Anweisungen unter Bevor Sie im Inneren Ihres Computers arbeiten. Befolgen Sie nach Arbeiten im Inneren des Computers die Anweisungen unter. nach Abschluss der Arbeiten im Inneren Ihres Computers.
2 Entfernen Sie das Speichermodul aus dem Speichermodulsteckplatz.
Wiedereinbauen der Speichermodule WARNUNG: Bevor Sie Arbeiten im Inneren des Computers ausführen, lesen Sie zunächst die im Lieferumfang des Computers enthaltenen Sicherheitshinweise und befolgen Sie die Anweisungen unter Bevor Sie im Inneren Ihres Computers arbeiten. Befolgen Sie nach Arbeiten im Inneren des Computers die Anweisungen unter. nach Abschluss der Arbeiten im Inneren Ihres Computers.
2 Drücken Sie das Speichermodul nach unten, bis es mit einem Klicken einrastet. ANMERKUNG: Wenn kein Klicken zu vernehmen ist, entfernen Sie das Speichermodul und installieren Sie es erneut. Voraussetzungen nach der Arbeit am Computer Bringen Sie die Bodenabdeckung wieder an.
Entfernen des Festplattenlaufwerks WARNUNG: Bevor Sie Arbeiten im Inneren des Computers ausführen, lesen Sie zunächst die im Lieferumfang des Computers enthaltenen Sicherheitshinweise und befolgen Sie die Anweisungen unter Bevor Sie im Inneren Ihres Computers arbeiten. Befolgen Sie nach Arbeiten im Inneren des Computers die Anweisungen unter. nach Abschluss der Arbeiten im Inneren Ihres Computers.
3 Heben Sie die Festplattenbaugruppe zusammen mit dem Kabel aus dem Computersockel. 4 Trennen Sie den Interposer von der Festplattenbaugruppe. 5 Entfernen Sie die vier Schrauben (M3x3), mit denen die Festplattenlaufwerkhalterung an der Festplatte befestigt ist.
6 28 Entfernen Sie die Festplattenlaufwerkhalterung vom Festplattenlaufwerk.
Wiedereinbauen der Festplatte WARNUNG: Bevor Sie Arbeiten im Inneren des Computers ausführen, lesen Sie zunächst die im Lieferumfang des Computers enthaltenen Sicherheitshinweise und befolgen Sie die Anweisungen unter Bevor Sie im Inneren Ihres Computers arbeiten. Befolgen Sie nach Arbeiten im Inneren des Computers die Anweisungen unter. nach Abschluss der Arbeiten im Inneren Ihres Computers.
Entfernen des SSD-Laufwerks WARNUNG: Bevor Sie Arbeiten im Inneren des Computers ausführen, lesen Sie zunächst die im Lieferumfang des Computers enthaltenen Sicherheitshinweise und befolgen Sie die Anweisungen unter Bevor Sie im Inneren Ihres Computers arbeiten. Befolgen Sie nach Arbeiten im Inneren des Computers die Anweisungen unter. nach Abschluss der Arbeiten im Inneren Ihres Computers.
3 Schieben Sie das SSD-Laufwerk aus dem SSD-Steckplatz.
Wiedereinbauen des SSDLaufwerks WARNUNG: Bevor Sie Arbeiten im Inneren des Computers ausführen, lesen Sie zunächst die im Lieferumfang des Computers enthaltenen Sicherheitshinweise und befolgen Sie die Anweisungen unter Bevor Sie im Inneren Ihres Computers arbeiten. Befolgen Sie nach Arbeiten im Inneren des Computers die Anweisungen unter. nach Abschluss der Arbeiten im Inneren Ihres Computers.
4 Befestigen Sie wieder die Schraube (M2x3), mit der das Solid-State-Laufwerk und die Solid-State-Laufwerkabdeckung am Computersockel befestigt ist. Voraussetzungen nach der Arbeit am Computer Bringen Sie die Bodenabdeckung wieder an.
Entfernen der Wireless-Karte WARNUNG: Bevor Sie Arbeiten im Inneren des Computers ausführen, lesen Sie zunächst die im Lieferumfang des Computers enthaltenen Sicherheitshinweise und befolgen Sie die Anweisungen unter Bevor Sie im Inneren Ihres Computers arbeiten. Befolgen Sie nach Arbeiten im Inneren des Computers die Anweisungen unter. nach Abschluss der Arbeiten im Inneren Ihres Computers.
3 Ziehen Sie die Wireless-Card aus dem Mini-Card-Steckplatz heraus.
Wiedereinbauen der WirelessKarte WARNUNG: Bevor Sie Arbeiten im Inneren des Computers ausführen, lesen Sie zunächst die im Lieferumfang des Computers enthaltenen Sicherheitshinweise und befolgen Sie die Anweisungen unter Bevor Sie im Inneren Ihres Computers arbeiten. Befolgen Sie nach Arbeiten im Inneren des Computers die Anweisungen unter. nach Abschluss der Arbeiten im Inneren Ihres Computers.
4 Verbinden Sie die Antennenkabel mit der Wireless-Karte. Die folgende Tabelle enthält die Farbcodierung der Antennenkabel für alle von Ihrem Computer unterstützten Wireless-Karten. Tabelle 2. Farbcodierung des Antennenkabels Anschlüsse auf der Wireless-Karte Antennenkabelfarbe Netzkabel (weißes Dreieck) Weiß Auxiliary-Kabel (schwarzes Dreieck) Schwarz Voraussetzungen nach der Arbeit am Computer Bringen Sie die Bodenabdeckung wieder an.
Entfernen der Tastatur WARNUNG: Bevor Sie Arbeiten im Inneren des Computers ausführen, lesen Sie zunächst die im Lieferumfang des Computers enthaltenen Sicherheitshinweise und befolgen Sie die Anweisungen unter Bevor Sie im Inneren Ihres Computers arbeiten. Befolgen Sie nach Arbeiten im Inneren des Computers die Anweisungen unter. nach Abschluss der Arbeiten im Inneren Ihres Computers.
3 Drehen Sie die Tastatur vorsichtig um und platzieren Sie sie über der Handballenstützen-Baugruppe. 4 Heben Sie die Riegel an und ziehen Sie das Tastaturkabel und das Kabel der Tastaturbeleuchtung von der Systemplatine ab.
5 40 Heben Sie die Tastatur zusammen mit dem Kabel aus der HandballenstützenBaugruppe heraus.
Wiedereinbauen der Tastatur WARNUNG: Bevor Sie Arbeiten im Inneren des Computers ausführen, lesen Sie zunächst die im Lieferumfang des Computers enthaltenen Sicherheitshinweise und befolgen Sie die Anweisungen unter Bevor Sie im Inneren Ihres Computers arbeiten. Befolgen Sie nach Arbeiten im Inneren des Computers die Anweisungen unter. nach Abschluss der Arbeiten im Inneren Ihres Computers.
Wenn Sie eine Ersatztastatur erhalten, sind die Kabel daran nicht gefaltet. Folgen Sie diesen Anweisungen, um die Kabel der Ersatztastatur in der gleichen Weise zu falten, wie die Kabel der alten Tastatur. ANMERKUNG: Das Tastaturbeleuchtungskabel ist nur bei einer Tastatur mit Hintergrundbeleuchtung vorhanden. 1 42 Platzieren Sie die Tastatur auf einer ebenen und sauberen Fläche.
2 Falten Sie das Kabel für die Tastaturhintergrundbeleuchtung vorsichtig bis zu dem Rand des Tastaturkabels, wie in der Abbildung dargestellt.
3 44 Falten Sie das Tastaturkabel vorsichtig, sodass das Kabelende an der Faltlinie, wie in der Abbildung dargestellt, ausgerichtet ist.
Entfernen der Handballenstütze WARNUNG: Bevor Sie Arbeiten im Inneren des Computers ausführen, lesen Sie zunächst die im Lieferumfang des Computers enthaltenen Sicherheitshinweise und befolgen Sie die Anweisungen unter Bevor Sie im Inneren Ihres Computers arbeiten. Befolgen Sie nach Arbeiten im Inneren des Computers die Anweisungen unter. nach Abschluss der Arbeiten im Inneren Ihres Computers.
3 Entfernen Sie die zwei Schrauben (M2x5), mit denen die HandballenstützenBaugruppe am Computersockel befestigt ist. 4 Schließen Sie den Bildschirm, und drehen Sie den Computer mit der Unterseite nach oben.
5 Entfernen Sie die vier Schrauben (M2x5), mit denen die HandballenstützenBaugruppe am Computersockel befestigt ist.
6 Heben Sie den Computersockel leicht an und lösen Sie die Laschen an der Handballenstützen-Baugruppe mit einem flachen Kunststoffstift aus den Steckplätzen am Computersockel. 7 Drehen Sie den Computer um und öffnen Sie den Bildschirm so weit wie möglich.
8 Heben Sie die Handballenstützenbaugruppe vom Computersockel ab.
Austauschen der Handballenstütze WARNUNG: Bevor Sie Arbeiten im Inneren des Computers ausführen, lesen Sie zunächst die im Lieferumfang des Computers enthaltenen Sicherheitshinweise und befolgen Sie die Anweisungen unter Bevor Sie im Inneren Ihres Computers arbeiten. Befolgen Sie nach Arbeiten im Inneren des Computers die Anweisungen unter. nach Abschluss der Arbeiten im Inneren Ihres Computers.
4 Bringen Sie die Bodenabdeckung wieder an.
Entfernen der Knopfzellenbatterie WARNUNG: Bevor Sie Arbeiten im Inneren des Computers ausführen, lesen Sie zunächst die im Lieferumfang des Computers enthaltenen Sicherheitshinweise und befolgen Sie die Anweisungen unter Bevor Sie im Inneren Ihres Computers arbeiten. Befolgen Sie nach Arbeiten im Inneren des Computers die Anweisungen unter. nach Abschluss der Arbeiten im Inneren Ihres Computers.
2 Verwenden Sie einen flachen Kunststoffstift, um die Knopfzellenbatterie aus der Batteriehalterung auf dem Computersockel zu hebeln.
Wiedereinbauen der Knopfzellenbatterie WARNUNG: Bevor Sie Arbeiten im Inneren des Computers ausführen, lesen Sie zunächst die im Lieferumfang des Computers enthaltenen Sicherheitshinweise und befolgen Sie die Anweisungen unter Bevor Sie im Inneren Ihres Computers arbeiten. Befolgen Sie nach Arbeiten im Inneren des Computers die Anweisungen unter. nach Abschluss der Arbeiten im Inneren Ihres Computers.
Ausbauen der Statusanzeigeplatine WARNUNG: Bevor Sie Arbeiten im Inneren des Computers ausführen, lesen Sie zunächst die im Lieferumfang des Computers enthaltenen Sicherheitshinweise und befolgen Sie die Anweisungen unter Bevor Sie im Inneren Ihres Computers arbeiten. Befolgen Sie nach Arbeiten im Inneren des Computers die Anweisungen unter. nach Abschluss der Arbeiten im Inneren Ihres Computers.
3 56 Heben Sie die Statusanzeigeplatine aus dem Computersockel heraus.
Austauschen der Statusanzeigeplatine WARNUNG: Bevor Sie Arbeiten im Inneren des Computers ausführen, lesen Sie zunächst die im Lieferumfang des Computers enthaltenen Sicherheitshinweise und befolgen Sie die Anweisungen unter Bevor Sie im Inneren Ihres Computers arbeiten. Befolgen Sie nach Arbeiten im Inneren des Computers die Anweisungen unter. nach Abschluss der Arbeiten im Inneren Ihres Computers.
Entfernen der Lüfter WARNUNG: Bevor Sie Arbeiten im Inneren des Computers ausführen, lesen Sie zunächst die im Lieferumfang des Computers enthaltenen Sicherheitshinweise und befolgen Sie die Anweisungen unter Bevor Sie im Inneren Ihres Computers arbeiten. Befolgen Sie nach Arbeiten im Inneren des Computers die Anweisungen unter. nach Abschluss der Arbeiten im Inneren Ihres Computers.
3 Heben Sie den linken Lüfter zusammen mit dem Kabel vom Computersockel ab. 4 Ziehen Sie das Kabel des rechten Lüfters von der Systemplatine ab.
5 60 Heben Sie den rechten Lüfter zusammen mit dem Kabel vom Computersockel ab.
Einbauen der Lüfter WARNUNG: Bevor Sie Arbeiten im Inneren des Computers ausführen, lesen Sie zunächst die im Lieferumfang des Computers enthaltenen Sicherheitshinweise und befolgen Sie die Anweisungen unter Bevor Sie im Inneren Ihres Computers arbeiten. Befolgen Sie nach Arbeiten im Inneren des Computers die Anweisungen unter. nach Abschluss der Arbeiten im Inneren Ihres Computers.
Entfernen des Netzadapteranschlusses WARNUNG: Bevor Sie Arbeiten im Inneren des Computers ausführen, lesen Sie zunächst die im Lieferumfang des Computers enthaltenen Sicherheitshinweise und befolgen Sie die Anweisungen unter Bevor Sie im Inneren Ihres Computers arbeiten. Befolgen Sie nach Arbeiten im Inneren des Computers die Anweisungen unter. nach Abschluss der Arbeiten im Inneren Ihres Computers.
2 Ziehen Sie das Netzadapteranschlusskabel aus den Kabelführungen am Computersockel und drehen Sie den Computer um.
3 64 Schieben Sie das Kabel durch die Steckplätze im Computersockel und heben Sie den Netzadapteranschluss mit dem zugehörigen Kabel aus dem Computersockel.
Wiedereinbauen des Netzadapteranschlusses WARNUNG: Bevor Sie Arbeiten im Inneren des Computers ausführen, lesen Sie zunächst die im Lieferumfang des Computers enthaltenen Sicherheitshinweise und befolgen Sie die Anweisungen unter Bevor Sie im Inneren Ihres Computers arbeiten. Befolgen Sie nach Arbeiten im Inneren des Computers die Anweisungen unter. nach Abschluss der Arbeiten im Inneren Ihres Computers.
Entfernen der E/A-Platine WARNUNG: Bevor Sie Arbeiten im Inneren des Computers ausführen, lesen Sie zunächst die im Lieferumfang des Computers enthaltenen Sicherheitshinweise und befolgen Sie die Anweisungen unter Bevor Sie im Inneren Ihres Computers arbeiten. Befolgen Sie nach Arbeiten im Inneren des Computers die Anweisungen unter. nach Abschluss der Arbeiten im Inneren Ihres Computers.
4 Ziehen Sie an der Freigabelasche und heben Sie die E/A-Platine aus dem Computersockel heraus.
Wiedereinbauen der E/A-Platine WARNUNG: Bevor Sie Arbeiten im Inneren des Computers ausführen, lesen Sie zunächst die im Lieferumfang des Computers enthaltenen Sicherheitshinweise und befolgen Sie die Anweisungen unter Bevor Sie im Inneren Ihres Computers arbeiten. Befolgen Sie nach Arbeiten im Inneren des Computers die Anweisungen unter. nach Abschluss der Arbeiten im Inneren Ihres Computers.
Entfernen der Systemplatine WARNUNG: Bevor Sie Arbeiten im Inneren des Computers ausführen, lesen Sie zunächst die im Lieferumfang des Computers enthaltenen Sicherheitshinweise und befolgen Sie die Anweisungen unter Bevor Sie im Inneren Ihres Computers arbeiten. Befolgen Sie nach Arbeiten im Inneren des Computers die Anweisungen unter. nach Abschluss der Arbeiten im Inneren Ihres Computers.
Vorgehensweise 1 Trennen Sie mit der Zuglasche das Bildschirmkabel von der Systemplatine. 2 Trennen Sie das Netzadapteranschlusskabel von der Systemplatine. 3 Den Computer herumdrehen und den Bildschirm öffnen. 4 Trennen Sie das Lautsprecherkabel von der Systemplatine. 5 Ziehen Sie das Klebeband ab, mit dem das E/A-Platinenkabel mit der Systemplatine verbunden ist, um den Riegel zu öffnen, und trennen Sie das E/APlatinenkabel von der Systemplatine.
8 Trennen Sie das Kabel der Knopfzellenbatterie von der Systemplatine.
9 Heben Sie die Systemplatine an einer Ecke an und lösen Sie die Systemplatinenanschlüsse von den Steckplätzen am Computersockel. 10 Entfernen Sie die Lautsprecher. 11 Entfernen Sie den Kühlkörper.
Wiedereinbauen der Systemplatine WARNUNG: Bevor Sie Arbeiten im Inneren des Computers ausführen, lesen Sie zunächst die im Lieferumfang des Computers enthaltenen Sicherheitshinweise und befolgen Sie die Anweisungen unter Bevor Sie im Inneren Ihres Computers arbeiten. Befolgen Sie nach Arbeiten im Inneren des Computers die Anweisungen unter. nach Abschluss der Arbeiten im Inneren Ihres Computers.
9 Schließen Sie den Bildschirm, und drehen Sie den Computer mit der Unterseite nach oben. 10 Verbinden Sie Netzadapteranschlusskabel und Bildschirmkabel mit der Systemplatine. Voraussetzungen nach der Arbeit am Computer 1 Setzen Sie die Lüfter ein. 2 Bauen Sie die E/A-Platine wieder ein. 3 Bauen Sie die Handballenstützen-Baugruppe wieder ein. 4 Bringen Sie die Tastatur wieder an. 5 Setzen Sie die Wireless-Karte wieder ein. 6 Bauen Sie das Solid-State-Laufwerk wieder ein.
Entfernen des Kühlkörpers WARNUNG: Bevor Sie Arbeiten im Inneren des Computers ausführen, lesen Sie zunächst die im Lieferumfang des Computers enthaltenen Sicherheitshinweise und befolgen Sie die Anweisungen unter Bevor Sie im Inneren Ihres Computers arbeiten. Befolgen Sie nach Arbeiten im Inneren des Computers die Anweisungen unter. nach Abschluss der Arbeiten im Inneren Ihres Computers.
Vorgehensweise ANMERKUNG: Das Aussehen des Kühlkörpers auf Ihrem Computer unterscheiden sich eventuell von der Abbildung in diesem Kapitel. 1 Legen Sie die Systemplatine auf eine saubere und ebene Oberfläche. 2 Lösen Sie der Reihe nach (Reihenfolge auf dem Kühlkörper angegeben) die unverlierbaren Schrauben, mit denen der Kühlkörper auf der Systemplatine befestigt ist. 3 Heben Sie den Kühlkörper von der Systemplatine.
Wiedereinbauen des Kühlkörpers WARNUNG: Bevor Sie Arbeiten im Inneren des Computers ausführen, lesen Sie zunächst die im Lieferumfang des Computers enthaltenen Sicherheitshinweise und befolgen Sie die Anweisungen unter Bevor Sie im Inneren Ihres Computers arbeiten. Befolgen Sie nach Arbeiten im Inneren des Computers die Anweisungen unter. nach Abschluss der Arbeiten im Inneren Ihres Computers.
6 Setzen Sie die Wireless-Karte wieder ein. 7 Bauen Sie das Solid-State-Laufwerk wieder ein. 8 Setzen Sie die Speichermodule wieder ein. 9 Befolgen Sie das Verfahren von Schritt 4 bis Schritt 6 im Abschnitt „Wiedereinbauen des Festplattenlaufwerks“. 10 Bauen Sie den Akku wieder ein. 11 Bringen Sie die Bodenabdeckung wieder an.
Entfernen der Lautsprecher WARNUNG: Bevor Sie Arbeiten im Inneren des Computers ausführen, lesen Sie zunächst die im Lieferumfang des Computers enthaltenen Sicherheitshinweise und befolgen Sie die Anweisungen unter Bevor Sie im Inneren Ihres Computers arbeiten. Befolgen Sie nach Arbeiten im Inneren des Computers die Anweisungen unter. nach Abschluss der Arbeiten im Inneren Ihres Computers.
2 80 Schieben Sie den Lautsprecher aus der Systemplatine.
Wiedereinbauen der Lautsprecher WARNUNG: Bevor Sie Arbeiten im Inneren des Computers ausführen, lesen Sie zunächst die im Lieferumfang des Computers enthaltenen Sicherheitshinweise und befolgen Sie die Anweisungen unter Bevor Sie im Inneren Ihres Computers arbeiten. Befolgen Sie nach Arbeiten im Inneren des Computers die Anweisungen unter. nach Abschluss der Arbeiten im Inneren Ihres Computers.
7 Bauen Sie das Solid-State-Laufwerk wieder ein. 8 Setzen Sie die Speichermodule wieder ein. 9 Befolgen Sie das Verfahren von Schritt 4 bis Schritt 6 im Abschnitt „Wiedereinbauen des Festplattenlaufwerks“. 10 Bauen Sie den Akku wieder ein. 11 Bringen Sie die Bodenabdeckung wieder an.
Entfernen des Subwoofers WARNUNG: Bevor Sie Arbeiten im Inneren des Computers ausführen, lesen Sie zunächst die im Lieferumfang des Computers enthaltenen Sicherheitshinweise und befolgen Sie die Anweisungen unter Bevor Sie im Inneren Ihres Computers arbeiten. Befolgen Sie nach Arbeiten im Inneren des Computers die Anweisungen unter. nach Abschluss der Arbeiten im Inneren Ihres Computers.
3 84 Heben Sie den Subwoofer aus dem Computersockel heraus.
Wiedereinbauen des Subwoofers WARNUNG: Bevor Sie Arbeiten im Inneren des Computers ausführen, lesen Sie zunächst die im Lieferumfang des Computers enthaltenen Sicherheitshinweise und befolgen Sie die Anweisungen unter Bevor Sie im Inneren Ihres Computers arbeiten. Befolgen Sie nach Arbeiten im Inneren des Computers die Anweisungen unter. nach Abschluss der Arbeiten im Inneren Ihres Computers.
8 Setzen Sie die Speichermodule wieder ein. 9 Befolgen Sie das Verfahren von Schritt 4 bis Schritt 6 im Abschnitt „Wiedereinbauen des Festplattenlaufwerks“. 10 Bauen Sie den Akku wieder ein. 11 Bringen Sie die Bodenabdeckung wieder an.
Entfernen der Bildschirmbaugruppe WARNUNG: Bevor Sie Arbeiten im Inneren des Computers ausführen, lesen Sie zunächst die im Lieferumfang des Computers enthaltenen Sicherheitshinweise und befolgen Sie die Anweisungen unter Bevor Sie im Inneren Ihres Computers arbeiten. Befolgen Sie nach Arbeiten im Inneren des Computers die Anweisungen unter. nach Abschluss der Arbeiten im Inneren Ihres Computers.
6 Schieben Sie das Bildschirmkabel und die Antennenkabel durch die Schlitze am Computersockel. 7 Entfernen Sie die vier Schrauben (M2x5), mit denen die Bildschirmbaugruppe am Computersockel befestigt ist.
8 Heben Sie die Bildschirmbaugruppe vom Computersockel ab.
Wiedereinsetzen der Bildschirmbaugruppe WARNUNG: Bevor Sie Arbeiten im Inneren des Computers ausführen, lesen Sie zunächst die im Lieferumfang des Computers enthaltenen Sicherheitshinweise und befolgen Sie die Anweisungen unter Bevor Sie im Inneren Ihres Computers arbeiten. Befolgen Sie nach Arbeiten im Inneren des Computers die Anweisungen unter. nach Abschluss der Arbeiten im Inneren Ihres Computers.
2 Bauen Sie die Handballenstützen-Baugruppe wieder ein. 3 Bringen Sie die Tastatur wieder an. 4 Befolgen Sie das Verfahren von Schritt 4 bis Schritt 6 im Abschnitt „Wiedereinbauen des Festplattenlaufwerks“. 5 Bauen Sie den Akku wieder ein. 6 Bringen Sie die Bodenabdeckung wieder an.
Entfernen der Bildschirmblende WARNUNG: Bevor Sie Arbeiten im Inneren des Computers ausführen, lesen Sie zunächst die im Lieferumfang des Computers enthaltenen Sicherheitshinweise und befolgen Sie die Anweisungen unter Bevor Sie im Inneren Ihres Computers arbeiten. Befolgen Sie nach Arbeiten im Inneren des Computers die Anweisungen unter. nach Abschluss der Arbeiten im Inneren Ihres Computers.
2 Heben Sie die Blende aus der Bildschirmbaugruppe.
Wiedereinbauen der Bildschirmblende WARNUNG: Bevor Sie Arbeiten im Inneren des Computers ausführen, lesen Sie zunächst die im Lieferumfang des Computers enthaltenen Sicherheitshinweise und befolgen Sie die Anweisungen unter Bevor Sie im Inneren Ihres Computers arbeiten. Befolgen Sie nach Arbeiten im Inneren des Computers die Anweisungen unter. nach Abschluss der Arbeiten im Inneren Ihres Computers.
Entfernen des Bildschirms WARNUNG: Bevor Sie Arbeiten im Inneren des Computers ausführen, lesen Sie zunächst die im Lieferumfang des Computers enthaltenen Sicherheitshinweise und befolgen Sie die Anweisungen unter Bevor Sie im Inneren Ihres Computers arbeiten. Befolgen Sie nach Arbeiten im Inneren des Computers die Anweisungen unter. nach Abschluss der Arbeiten im Inneren Ihres Computers.
2 Heben Sie den Bildschirm vorsichtig an und drehen Sie ihn um. 3 Ziehen Sie das Klebeband ab, mit dem das Bildschirmkabel am Bildschirm befestigt ist. 4 Öffnen Sie den Riegel an und trennen Sie das Bildschirmkabel vom Bildschirm.
5 Heben Sie das Bildschirmbedienfeld von der hinteren Bildschirmabdeckung und der Antennenbaugruppe ab.
Wiedereinbauen des Bildschirms WARNUNG: Bevor Sie Arbeiten im Inneren des Computers ausführen, lesen Sie zunächst die im Lieferumfang des Computers enthaltenen Sicherheitshinweise und befolgen Sie die Anweisungen unter Bevor Sie im Inneren Ihres Computers arbeiten. Befolgen Sie nach Arbeiten im Inneren des Computers die Anweisungen unter. nach Abschluss der Arbeiten im Inneren Ihres Computers.
7 Bauen Sie den Akku wieder ein. 8 Bringen Sie die Bodenabdeckung wieder an.
Entfernen der Kamera WARNUNG: Bevor Sie Arbeiten im Inneren des Computers ausführen, lesen Sie zunächst die im Lieferumfang des Computers enthaltenen Sicherheitshinweise und befolgen Sie die Anweisungen unter Bevor Sie im Inneren Ihres Computers arbeiten. Befolgen Sie nach Arbeiten im Inneren des Computers die Anweisungen unter. nach Abschluss der Arbeiten im Inneren Ihres Computers.
3 Trennen Sie das Kamerakabel von der Kamera.
Wiedereinbauen der Kamera WARNUNG: Bevor Sie Arbeiten im Inneren des Computers ausführen, lesen Sie zunächst die im Lieferumfang des Computers enthaltenen Sicherheitshinweise und befolgen Sie die Anweisungen unter Bevor Sie im Inneren Ihres Computers arbeiten. Befolgen Sie nach Arbeiten im Inneren des Computers die Anweisungen unter. nach Abschluss der Arbeiten im Inneren Ihres Computers.
Entfernen des Bildschirmkabels WARNUNG: Bevor Sie Arbeiten im Inneren des Computers ausführen, lesen Sie zunächst die im Lieferumfang des Computers enthaltenen Sicherheitshinweise und befolgen Sie die Anweisungen unter Bevor Sie im Inneren Ihres Computers arbeiten. Befolgen Sie nach Arbeiten im Inneren des Computers die Anweisungen unter. nach Abschluss der Arbeiten im Inneren Ihres Computers.
3 Entfernen Sie das Bildschirmkabel aus den Kabelführungen auf der hinteren Bildschirmabdeckung und der Antennenbaugruppe. 4 Lösen Sie das Bildschirmkabel von der hinteren Bildschirmabdeckung und der Antennenbaugruppe.
Wiederbefestigen des Bildschirmkabels WARNUNG: Bevor Sie Arbeiten im Inneren des Computers ausführen, lesen Sie zunächst die im Lieferumfang des Computers enthaltenen Sicherheitshinweise und befolgen Sie die Anweisungen unter Bevor Sie im Inneren Ihres Computers arbeiten. Befolgen Sie nach Arbeiten im Inneren des Computers die Anweisungen unter. nach Abschluss der Arbeiten im Inneren Ihres Computers.
8 Befolgen Sie das Verfahren von Schritt 4 bis Schritt 6 im Abschnitt „Wiedereinbauen des Festplattenlaufwerks“. 9 Bauen Sie den Akku wieder ein. 10 Bringen Sie die Bodenabdeckung wieder an.
Entfernen des Bildschirmscharniers und der Halterungsbaugruppe WARNUNG: Bevor Sie Arbeiten im Inneren des Computers ausführen, lesen Sie zunächst die im Lieferumfang des Computers enthaltenen Sicherheitshinweise und befolgen Sie die Anweisungen unter Bevor Sie im Inneren Ihres Computers arbeiten. Befolgen Sie nach Arbeiten im Inneren des Computers die Anweisungen unter. nach Abschluss der Arbeiten im Inneren Ihres Computers.
2 Notieren Sie sich die Bildschirmkabelführung und entfernen Sie das Bildschirmkabel aus den Kabelführungen an den Bildschirmscharnieren. 3 Entfernen Sie die vier Schrauben (M2x3), mit denen die Bildschirmscharniere an der hinteren Bildschirmabdeckung befestigt sind. 4 Entfernen Sie die zwei Schrauben (M2x3), mit denen die Halterungsbaugruppe an der hinteren Bildschirmabdeckung befestigt ist.
Wiedereinbauen des Bildschirmscharniers und der Halterungsbaugruppe WARNUNG: Bevor Sie Arbeiten im Inneren des Computers ausführen, lesen Sie zunächst die im Lieferumfang des Computers enthaltenen Sicherheitshinweise und befolgen Sie die Anweisungen unter Bevor Sie im Inneren Ihres Computers arbeiten. Befolgen Sie nach Arbeiten im Inneren des Computers die Anweisungen unter. nach Abschluss der Arbeiten im Inneren Ihres Computers.
6 Bringen Sie die Tastatur wieder an. 7 Befolgen Sie das Verfahren von Schritt 4 bis Schritt 6 im Abschnitt „Wiedereinbauen des Festplattenlaufwerks“. 8 Bauen Sie den Akku wieder ein. 9 Bringen Sie die Bodenabdeckung wieder an.
Entfernen der hinteren Bildschirmabdeckung und der Antennenbaugruppe WARNUNG: Bevor Sie Arbeiten im Inneren des Computers ausführen, lesen Sie zunächst die im Lieferumfang des Computers enthaltenen Sicherheitshinweise und befolgen Sie die Anweisungen unter Bevor Sie im Inneren Ihres Computers arbeiten. Befolgen Sie nach Arbeiten im Inneren des Computers die Anweisungen unter. nach Abschluss der Arbeiten im Inneren Ihres Computers.
Vorgehensweise Nachdem die unter „Voraussetzungen“ beschriebenen Schritte ausgeführt wurden, verbleiben die hintere Bildschirmabdeckung und die Antennenbaugruppe.
Austauschen der hinteren Bildschirmabdeckung und der Antennenbaugruppe WARNUNG: Bevor Sie Arbeiten im Inneren des Computers ausführen, lesen Sie zunächst die im Lieferumfang des Computers enthaltenen Sicherheitshinweise und befolgen Sie die Anweisungen unter Bevor Sie im Inneren Ihres Computers arbeiten. Befolgen Sie nach Arbeiten im Inneren des Computers die Anweisungen unter. nach Abschluss der Arbeiten im Inneren Ihres Computers.
11 114 Bringen Sie die Bodenabdeckung wieder an.
Aktualisieren des BIOS Sie müssen evtl. das BIOS aktualisieren, wenn eine Aktualisierung verfügbar ist oder die Systemplatine ausgetauscht wurde. So flashen Sie das BIOS: 1 Schalten Sie den Computer ein. 2 Rufen Sie die Website www.dell.com/support auf. 3 Klicken Sie auf Product Support (Produktsupport), geben Sie die Service-TagNummer Ihres Computers ein und klicken Sie auf Submit (Senden).
Diagnose Stromversorgungs- und Akkuzustandsanzeige/Festplattenaktivitätsanzeige: Zeigt den Akkuladezustand oder die Festplattenaktivität an. ANMERKUNG: Drücken Sie Fn+H, um diese Anzeigeleuchte zwischen Strom-/ Akkustatusanzeige und Festplattenaktivitätsanzeige umzuschalten. Festplattenaktivitätsanzeige Leuchtet, wenn der Computer auf das Festplattenlaufwerk zugreift. Strom- und Akkustatusanzeige Zeigt den Strom- und Akkuladestatus an.
Anzeigemuster Problembeschreibung 2,5 Unzulässiger Speicher installiert 2,6 Systemplatinen- oder Chipsatzfehler 2,7 LCD-Fehler 3,1 CMOS-Akkufehler 3,2 Fehler bei PCI- oder Videokarte 3,3 Recovery Image nicht gefunden 3,4 Recovery Image gefunden aber ungültig Kamerastatusanzeige: Gibt an, ob die Kamera in Betrieb ist. • Stetig weiß leuchtend – Kamera ist in Betrieb. • Aus – Kamera ist nicht in Betrieb.
Hilfe erhalten und Kontaktaufnahme mit Dell Selbsthilfe-Ressourcen Mithilfe dieser Selbsthilfe-Ressourcen erhalten Sie Informationen und Hilfe zu DellProdukten: Tabelle 4. Selbsthilfe-Ressourcen Informationen zu Produkten und Dienstleistungen von Dell www.dell.com Anwendung Dell Help & Support (Dell Hilfe und Support) Erste Schritte-Anwendung Aufrufen der Hilfe Geben Sie in der Windows-Suche Help and Support ein und drücken Sie die Eingabetaste. Onlinehilfe für Betriebssystem www.dell.
Kontaktaufnahme mit Dell Informationen zur Kontaktaufnahme mit Dell für den Verkauf, den technischen Support und den Kundendienst erhalten Sie unter www.dell.com/contactdell. ANMERKUNG: Die Verfügbarkeit ist je nach Land und Produkt unterschiedlich, und bestimmte Dienstleistungen sind in Ihrer Region eventuell nicht verfügbar.