Inspiron 24 3000 Series 서비스 설명서 컴퓨터 모델: Inspiron 24–3452 규정 모델: W12C 규정 유형: W12C002
참고, 주의 및 경고 노트: "주"는 컴퓨터를 보다 효율적으로 사용하는 데 도움을 주는 중요 정보를 제공 합니다. 주의: "주의"는 하드웨어 손상이나 데이터 손실의 가능성을 설명하며, 이러한 문제 를 방지할 수 있는 방법을 알려줍니다. 경고: "경고"는 재산상의 피해나 심각한 부상 또는 사망을 유발할 수 있는 위험이 있음을 알려줍니다. Copyright © 2015 Dell Inc. 저작권 본사 소유. 이 제품은 미국, 국제 저작권법 및 지적 재산권법에 의해 보호됩니다. Dell™ 및 Dell 로고는 미국 및/또는 기타 관할지역에서 사용되는 Dell Inc.의 상표 입니다. 이 문서에 언급된 기타 모든 표시 및 이름은 각 회사의 상표일 수 있습니다.
목차 컴퓨터 내부 작업을 시작하기 전에.............................................. 8 시작하기 전에 .................................................................................................... 8 안전 지침.............................................................................................................9 권장 도구.............................................................................................................9 컴퓨터 내부 작업을 마친 후에.....................................................11 기술 개요.....................
광학 드라이브 교체..................................................................... 22 절차...................................................................................................................22 작업후 필수 조건.............................................................................................. 22 하드 드라이브 분리......................................................................23 전제조건........................................................................................................... 23 절차.
방열판 장착.................................................................................. 37 절차...................................................................................................................37 작업후 필수 조건...............................................................................................37 팬 분리..........................................................................................38 전제조건...........................................................................................
카메라 장착..................................................................................49 절차.................................................................................................................. 49 작업후 필수 조건.............................................................................................. 49 시스템 보드 제거......................................................................... 50 전제조건.......................................................................................................
스피커 장착.................................................................................. 62 절차.................................................................................................................. 62 작업후 필수 조건.............................................................................................. 62 제어 버튼 보드 분리.................................................................... 63 전제조건.........................................................................................................
컴퓨터 내부 작업을 시작하기 전 에 주의: 구성 요소 및 카드의 손상을 방지하려면 구성 요소 및 카드를 잡을 때 핀이나 단자를 잡지 말고 모서리를 잡습니다. 노트: 이 문서의 이미지는 주문한 컴퓨터의 구성에 따라 조금씩 다를 수 있 습니다. 시작하기 전에 1 열려 있는 파일을 모두 저장하고 닫은 다음 사용 중인 응용 프로그램을 모두 종료합니다. 2 컴퓨터를 종료하십시오. – Windows 10: 시작 → 전원 → 종료를 클릭하거나 누릅니다. – Windows 8.1: 시작 화면에서 전원 아이콘을 클릭하거나 릭하거나 누릅니다. → 종료를클 – Windows 7: 시작 → 종료를 클릭하거나 누릅니다. 노트: 다른 운영 체제를 사용하고 있는 경우 해당 운영 체제의 설명서에 서 종료 지침을 참조하십시오. 3 컴퓨터 및 모든 연결된 장치를 전원 콘센트에서 분리하십시오. 4 전화선, 네트워크 케이블 등과 같은 모든 케이블을 컴퓨터에서 분리합니다.
안전 지침 컴퓨터의 손상을 방지하고 안전하게 작업하기 위해 다음 안전 지침을 따르십시 오. 경고: 컴퓨터의 내부 작업을 시작하기 전에 컴퓨터와 함께 제공된 안전 정보 를 반드시 읽고 숙지하십시오. 추가적인 안전에 관한 모범 사례 정보에 대해 서는 법적 규제 준수 홈 페이지(www.dell.com/regulatory_compliance)를 참조하십시오. 경고: 컴퓨터 덮개 또는 패널을 열기 전에 전원을 모두 분리합니다. 컴퓨터 내부에서 작업한 후에는 전원을 연결하기 전에 덮개, 패널 및 나사를 전부 장 착합니다. 주의: 컴퓨터의 손상을 방지하려면 작업 표면이 평평하고 깨끗한지 확인합 니다. 주의: 구성 요소 및 카드의 손상을 방지하려면 구성 요소 및 카드를 잡을 때 핀이나 단자를 잡지 말고 모서리를 잡습니다. 주의: Dell 기술 지원 팀에서 승인하거나 지시한 경우에만 문제 해결 및 수리 작업을 수행할 수 있습니다. Dell사에서 공인하지 않은 서비스로 인한 손상 에 대해서는 보상을 받을 수 없습니다.
• 10 플라스틱 스크라이브
컴퓨터 내부 작업을 마친 후에 주의: 컴퓨터 내부에 나사가 남아 있거나 느슨한 나사가 존재하는 경우 컴퓨 터가 심각하게 손상될 수 있습니다. 1 나사를 모두 장착하고 컴퓨터 내부에 남아 있는 나사가 없는지 확인합니다. 2 작업을 시작하기 전에 분리한 모든 외부 장치, 주변 장치 및 케이블을 컴퓨터 에 연결합니다. 3 작업을 시작하기 전에 분리한 모든 미디어 카드, 디스크 및 기타 부품을 다시 연결합니다. 4 전원 콘센트에 컴퓨터와 연결된 모든 장치를 연결합니다. 5 컴퓨터를 켭니다.
기술 개요 경고: 컴퓨터의 내부 작업을 시작하기 전에 컴퓨터와 함께 제공된 안전 정보 를 읽고 컴퓨터 내부에서 작업하기 전에의 단계를 따르십시오. 컴퓨터 내부 작업 후에는 컴퓨터에 내부에서 작업한 후에의 단계를 따르십시오. 안전 모 범 사례에 대한 자세한 내용은 www.dell.com/regulatory_compliance의 규정 준수 홈페이지를 참고하십시오.
스탠드 조립품 분리 경고: 컴퓨터의 내부 작업을 시작하기 전에 컴퓨터와 함께 제공된 안전 정보 를 읽고 컴퓨터 내부에서 작업하기 전에의 단계를 따르십시오. 컴퓨터 내부 작업 후에는 컴퓨터에 내부에서 작업한 후에의 단계를 따르십시오. 안전 모 범 사례에 대한 자세한 내용은 www.dell.com/regulatory_compliance의 규정 준수 홈페이지를 참고하십시오. 절차 1 손가락 끝으로 스탠드 덮개를 들어 올립니다. 2 스탠드 덮개를 일정한 각도로 스탠드에서 밀어 분리합니다. 3 1 스탠드 3 후면 덮개 2 스탠드 덮개 스탠드 브래킷을 후면 덮개에 고정하는 나사를 제거합니다.
4 14 스탠드를 들어 올려 후면 덮개에서 분리합니다.
스탠드 조립품 장착 경고: 컴퓨터의 내부 작업을 시작하기 전에 컴퓨터와 함께 제공된 안전 정보 를 읽고 컴퓨터 내부에서 작업하기 전에의 단계를 따르십시오. 컴퓨터 내부 작업 후에는 컴퓨터에 내부에서 작업한 후에의 단계를 따르십시오. 안전 모 범 사례에 대한 자세한 내용은 www.dell.com/regulatory_compliance의 규정 준수 홈페이지를 참고하십시오. 절차 1 스탠드 브래킷의 탭을 후면 덮개의 슬롯에 삽입해 스탠드 브래킷의 나사 구 멍이 후면 덮개의 나사 구멍에 맞추어 지도록 합니다. 2 스탠드 브래킷을 후면 덮개에 고정하는 나사를 장착합니다. 3 스탠드 브래킷의 스탠드 덮개를 밀어 장착합니다.
후면 덮개 제거 경고: 컴퓨터의 내부 작업을 시작하기 전에 컴퓨터와 함께 제공된 안전 정보 를 읽고 컴퓨터 내부에서 작업하기 전에의 단계를 따르십시오. 컴퓨터 내부 작업 후에는 컴퓨터에 내부에서 작업한 후에의 단계를 따르십시오. 안전 모 범 사례에 대한 자세한 내용은 www.dell.com/regulatory_compliance의 규정 준수 홈페이지를 참고하십시오. 전제조건 스탠드 조립품을 분리합니다. 절차 주의: 컴퓨터에 내부 액세서리를 설치해야 하는 경우가 아니면 컴퓨터 덮개 를 분리하지 마십시오. 1 16 플라스틱 스크라이브를 사용하여 디스플레이 베젤에서 후면 덮개를 들어 올 립니다.
2 후면 덮개를 들어 올려 컴퓨터에서 분리합니다.
후면 덮개 장착 경고: 컴퓨터의 내부 작업을 시작하기 전에 컴퓨터와 함께 제공된 안전 정보 를 읽고 컴퓨터 내부에서 작업하기 전에의 단계를 따르십시오. 컴퓨터 내부 작업 후에는 컴퓨터에 내부에서 작업한 후에의 단계를 따르십시오. 안전 모 범 사례에 대한 자세한 내용은 www.dell.com/regulatory_compliance의 규정 준수 홈페이지를 참고하십시오. 절차 후면 덮개의 탭을 디스플레이 베젤의 슬롯에 맞춘 다음 후면 덮개를 제자리에 밀 어 넣습니다. 작업후 필수 조건 스탠드 조립품을 장착합니다.
광학 드라이브 제거 경고: 컴퓨터의 내부 작업을 시작하기 전에 컴퓨터와 함께 제공된 안전 정보 를 읽고 컴퓨터 내부에서 작업하기 전에의 단계를 따르십시오. 컴퓨터 내부 작업 후에는 컴퓨터에 내부에서 작업한 후에의 단계를 따르십시오. 안전 모 범 사례에 대한 자세한 내용은 www.dell.com/regulatory_compliance의 규정 준수 홈페이지를 참고하십시오. 전제조건 1 스탠드 조립품을 분리합니다. 2 후면 덮개를 분리합니다. 절차 1 전원 및 데이터 케이블을 광학 드라이브에서 분리합니다. 2 광학 드라이브 조립품을 디스플레이 조립품 베이스에 고정하는 나사를 분리 합니다.
3 광학 드라이브 조립품을 밀어 광학 드라이브 베이에서 꺼냅니다. 1 광학 드라이브 조립품 3 전원 및 데이터 케이블 2 나사 4 광학 드라이브 베젤을 조심스럽게 당겨서 광학 드라이브에서 분리합니다. 5 광학 드라이브 브래킷을 광학 드라이브에 고정하는 나사를 분리합니다.
6 광학 드라이브에서 광학 드라이브 브래킷을 분리합니다.
광학 드라이브 교체 경고: 컴퓨터의 내부 작업을 시작하기 전에 컴퓨터와 함께 제공된 안전 정보 를 읽고 컴퓨터 내부에서 작업하기 전에의 단계를 따르십시오. 컴퓨터 내부 작업 후에는 컴퓨터에 내부에서 작업한 후에의 단계를 따르십시오. 안전 모 범 사례에 대한 자세한 내용은 www.dell.com/regulatory_compliance의 규정 준수 홈페이지를 참고하십시오. 절차 1 광학 드라이브 브래킷의 나사 구멍을 광학 드라이브의 나사 구멍에 맞춥니 다. 2 광학 드라이브 브래킷을 광학 드라이브에 고정하는 나사를 장착합니다. 3 광학 드라이브 베젤의 탭을 광학 드라이브 조립품의 슬롯에 맞추고 제자리에 끼웁니다. 4 광학 드라이브 조립품을 광학 드라이브 베이로 밀어 넣고 광학 드라이브 브 래킷의 나사 구멍이 디스플레이 조립품 베이스의 나사 구멍에 맞춰지는지 확 인합니다. 5 광학 드라이브 조립품을 디스플레이 조립품 베이스에 고정하는 나사를 장착 합니다.
하드 드라이브 분리 경고: 컴퓨터의 내부 작업을 시작하기 전에 컴퓨터와 함께 제공된 안전 정보 를 읽고 컴퓨터 내부에서 작업하기 전에의 단계를 따르십시오. 컴퓨터 내부 작업 후에는 컴퓨터에 내부에서 작업한 후에의 단계를 따르십시오. 안전 모 범 사례에 대한 자세한 내용은 www.dell.com/regulatory_compliance의 규정 준수 홈페이지를 참고하십시오. 주의: 하드 드라이브는 손상되기 쉽습니다. 하드 드라이브를 다룰 때는 조심 스럽게 다루십시오. 주의: 데이터 손실 위험이 있으므로 컴퓨터가 켜져 있거나 절전 모드인 상태 에서 하드 드라이브를 분리하지 마십시오. 전제조건 1 스탠드 조립품을 분리합니다. 2 후면 덮개를 분리합니다. 절차 1 전원 및 데이터 케이블을 하드 드라이브에서 분리합니다. 2 하드 드라이브 조립품을 디스플레이 조립품 베이스에 고정하는 나사를 분리 합니다.
3 4 24 손가락 끝으로 하드 드라이브 조립품을 하드 드라이브 베이에서 들어 올립니 다. 1 전원 및 데이터 케이블 2 하드 드라이브 조립품 3 나사 4 디스플레이 조립품 베이스 하드 드라이브 브래킷을 하드 드라이브에 고정시키는 나사를 제거합니다.
5 하드 드라이브 브래킷에서 하드 드라이브를 분리합니다.
하드 드라이브 장착 경고: 컴퓨터의 내부 작업을 시작하기 전에 컴퓨터와 함께 제공된 안전 정보 를 읽고 컴퓨터 내부에서 작업하기 전에의 단계를 따르십시오. 컴퓨터 내부 작업 후에는 컴퓨터에 내부에서 작업한 후에의 단계를 따르십시오. 안전 모 범 사례에 대한 자세한 내용은 www.dell.com/regulatory_compliance의 규정 준수 홈페이지를 참고하십시오. 주의: 하드 드라이브는 손상되기 쉽습니다. 하드 드라이브를 다룰 때는 조심 스럽게 다루십시오. 절차 1 하드 드라이브 브래킷의 나사 구멍을 하드 드라이브의 나사 구멍에 맞춥니 다. 2 하드 드라이브 브래킷을 하드 드라이브에 고정하는 나사를 장착합니다. 3 하드 드라이브 조립품을 하드 드라이브 베이로 밀어 넣고 하드 드라이브 브 래킷의 나사 구멍이 디스플레이 조립품 베이스의 나사 구멍에 맞춰지는지 확 인합니다. 4 하드 드라이브 조립품을 디스플레이 조립품 베이스에 고정하는 나사를 장착 합니다.
메모리 모듈 분리 경고: 컴퓨터의 내부 작업을 시작하기 전에 컴퓨터와 함께 제공된 안전 정보 를 읽고 컴퓨터 내부에서 작업하기 전에의 단계를 따르십시오. 컴퓨터 내부 작업 후에는 컴퓨터에 내부에서 작업한 후에의 단계를 따르십시오. 안전 모 범 사례에 대한 자세한 내용은 www.dell.com/regulatory_compliance의 규정 준수 홈페이지를 참고하십시오. 전제조건 1 스탠드 조립품을 분리합니다. 2 후면 덮개를 분리합니다. 절차 1 메모리 모듈이 튀어 나올 때까지 메모리 모듈 슬롯의 양쪽 끝에 있는 고정 클 립을 손끝으로 조심스럽게 벌립니다.
2 28 메모리 모듈 슬롯에서 메모리 모듈을 분리합니다.
메모리 모듈 장착 경고: 컴퓨터의 내부 작업을 시작하기 전에 컴퓨터와 함께 제공된 안전 정보 를 읽고 컴퓨터 내부에서 작업하기 전에의 단계를 따르십시오. 컴퓨터 내부 작업 후에는 컴퓨터에 내부에서 작업한 후에의 단계를 따르십시오. 안전 모 범 사례에 대한 자세한 내용은 www.dell.com/regulatory_compliance의 규정 준수 홈페이지를 참고하십시오. 절차 1 메모리 모듈의 노치를 메모리 모듈 슬롯의 탭에 맞춥니다.
2 메모리 모듈을 일정 각도로 밀어 넣고 딸깍 소리가 나면서 제자리에 고정될 때까지 메모리 모듈을 아래로 누릅니다. 노트: 소리가 나지 않으면 메모리 모듈을 분리했다가 다시 설치합니다. 1 노치 2 탭 3 고정 클립(2) 4 메모리 모듈 5 메모리 모듈 슬롯 작업후 필수 조건 1 후면 덮개를 장착합니다. 2 스탠드 조립품을 장착합니다.
무선 카드 분리 경고: 컴퓨터의 내부 작업을 시작하기 전에 컴퓨터와 함께 제공된 안전 정보 를 읽고 컴퓨터 내부에서 작업하기 전에의 단계를 따르십시오. 컴퓨터 내부 작업 후에는 컴퓨터에 내부에서 작업한 후에의 단계를 따르십시오. 안전 모 범 사례에 대한 자세한 내용은 www.dell.com/regulatory_compliance의 규정 준수 홈페이지를 참고하십시오. 전제조건 1 스탠드 조립품을 분리합니다. 2 후면 덮개를 분리합니다. 절차 1 무선 카드 브래킷과 무선 카드를 시스템 보드에 고정시키는 나사를 분리합니 다. 2 무선 카드 브래킷을 무선 카드에서 들어 올립니다. 3 안테나 케이블을 무선 카드의 커넥터에서 분리합니다.
4 32 무선 카드를 무선 카드 슬롯 바깥쪽으로 밀어 냅니다.
무선 카드 장착 경고: 컴퓨터의 내부 작업을 시작하기 전에 컴퓨터와 함께 제공된 안전 정보 를 읽고 컴퓨터 내부에서 작업하기 전에의 단계를 따르십시오. 컴퓨터 내부 작업 후에는 컴퓨터에 내부에서 작업한 후에의 단계를 따르십시오. 안전 모 범 사례에 대한 자세한 내용은 www.dell.com/regulatory_compliance의 규정 준수 홈페이지를 참고하십시오. 절차 1 무선 카드의 노치를 무선 카드 슬롯의 탭에 맞춥니다. 2 무선 카드를 넣고 무선 카드 슬롯에 삽입합니다. 3 무선 카드의 한쪽 끝을 아래로 누르고 무선 카드의 나사 구멍을 시스템 보드 의 나사 구멍에 맞춥니다. 4 무선 카드에 안테나 케이블을 연결합니다. 다음 표에는 컴퓨터에서 지원되는 무선 카드의 안테나 케이블 색상표가 제공 됩니다. 5 무선 카드의 커넥터 안테나 케이블 색상 주(흰색 삼각형) 흰색 보조(검정색 삼각형) 검정색 무선 카드 브래킷의 나사 구멍을 무선 카드의 나사 구멍에 맞춥니다.
6 무선 카드 브래킷과 무선 카드를 시스템 보드에 고정시키는 나사를 장착합니 다. 1 무선 카드 2 노치 3 탭 4 안테나 케이블 5 무선 카드 브래킷 6 나사 작업후 필수 조건 1 후면 덮개를 장착합니다. 2 스탠드 조립품을 장착합니다.
방열판 분리 경고: 컴퓨터의 내부 작업을 시작하기 전에 컴퓨터와 함께 제공된 안전 정보 를 읽고 컴퓨터 내부에서 작업하기 전에의 단계를 따르십시오. 컴퓨터 내부 작업 후에는 컴퓨터에 내부에서 작업한 후에의 단계를 따르십시오. 안전 모 범 사례에 대한 자세한 내용은 www.dell.com/regulatory_compliance의 규정 준수 홈페이지를 참고하십시오. 경고: 방열판이 정상 작동 중에 뜨거워질 수 있습니다. 충분한 시간 동안 방 열판을 충분히 식힌 다음 만지십시오. 주의: 최대 냉각 기능을 확보하려면 방열판의 열 전달 영역을 만지지 마십시 오. 피부의 기름기가 열 그리스의 열 전달 기능을 저하시킬 수 있습니다. 전제조건 1 스탠드 조립품을 분리합니다. 2 후면 덮개를 분리합니다. 절차 1 방열판을 시스템 보드에 고정시키는 조임 나사를 방열판에 표시된 번호 순서 대로 풀어 줍니다. 2 방열판을 디스플레이 조립품 베이스에 고정하는 나사를 분리합니다.
3 36 방열판을 들어 올려 시스템 보드에서 분리합니다.
방열판 장착 경고: 컴퓨터의 내부 작업을 시작하기 전에 컴퓨터와 함께 제공된 안전 정보 를 읽고 컴퓨터 내부에서 작업하기 전에의 단계를 따르십시오. 컴퓨터 내부 작업 후에는 컴퓨터에 내부에서 작업한 후에의 단계를 따르십시오. 안전 모 범 사례에 대한 자세한 내용은 www.dell.com/regulatory_compliance의 규정 준수 홈페이지를 참고하십시오. 주의: 프로세서 방열판을 잘못 맞추면 시스템 보드 및 프로세서가 손상될 수 있습니다. 노트: 기존 시스템 보드 및 팬을 함께 재설치할 경우 기존의 열 그리스를 다 시 사용할 수 있습니다. 시스템 보드 또는 팬이 교체된 경우 키트에 함께 제 공된 열 패드를 이용해 열 전도성을 확보합니다. 절차 1 방열판의 나사 구멍과 디스플레이 조립품 베이스의 나사 구멍을 맞춥니다. 2 방열판의 조임 나사를 시스템 보드의 나사 구멍에 맞춥니다. 3 방열판을 시스템 보드에 고정시키는 조임 나사를 방열판에 표시된 번호 순서 대로 조입니다.
팬 분리 경고: 컴퓨터의 내부 작업을 시작하기 전에 컴퓨터와 함께 제공된 안전 정보 를 읽고 컴퓨터 내부에서 작업하기 전에의 단계를 따르십시오. 컴퓨터 내부 작업 후에는 컴퓨터에 내부에서 작업한 후에의 단계를 따르십시오. 안전 모 범 사례에 대한 자세한 내용은 www.dell.com/regulatory_compliance의 규정 준수 홈페이지를 참고하십시오. 전제조건 1 스탠드 조립품을 분리합니다. 2 후면 덮개를 분리합니다. 절차 1 시스템 보드에서 팬 케이블을 분리합니다. 2 팬을 디스플레이 조립품 베이스에 고정시키는 나사를 제거합니다.
3 디스플레이 조립품 베이스의 팬을 일정 각도로 들어 올립니다.
팬 장착 경고: 컴퓨터의 내부 작업을 시작하기 전에 컴퓨터와 함께 제공된 안전 정보 를 읽고 컴퓨터 내부에서 작업하기 전에의 단계를 따르십시오. 컴퓨터 내부 작업 후에는 컴퓨터에 내부에서 작업한 후에의 단계를 따르십시오. 안전 모 범 사례에 대한 자세한 내용은 www.dell.com/regulatory_compliance의 규정 준수 홈페이지를 참고하십시오. 절차 1 팬을 일정 각도로 디스플레이 조립품 베이스에 장착합니다. 2 팬의 나사 구멍을 컴퓨터 디스플레이 조립품 베이스의 나사 구멍에 맞춥니 다. 3 디스플레이 조립품 베이스에 팬을 고정시키는 나사를 장착합니다. 4 팬 케이블을 시스템 보드에 연결합니다. 작업후 필수 조건 1 후면 덮개를 장착합니다. 2 스탠드 조립품을 장착합니다.
코인 셀 배터리 분리 경고: 컴퓨터의 내부 작업을 시작하기 전에 컴퓨터와 함께 제공된 안전 정보 를 읽고 컴퓨터 내부에서 작업하기 전에의 단계를 따르십시오. 컴퓨터 내부 작업 후에는 컴퓨터에 내부에서 작업한 후에의 단계를 따르십시오. 안전 모 범 사례에 대한 자세한 내용은 www.dell.com/regulatory_compliance의 규정 준수 홈페이지를 참고하십시오. 주의: 코인 셀 배터리를 분리하면 BIOS 설치 프로그램 설정이 기본값으로 재 설정됩니다. 분리하기 전에 BIOS 설치 프로그램의 설정을 기록하는 것이 좋 습니다. 전제조건 1 스탠드 조립품을 분리합니다. 2 후면 덮개를 분리합니다.
절차 플라스틱 스크라이브를 사용하여 조심스럽게 시스템 보드의 배터리 소켓에 서 코인 셀 배터리를 꺼냅니다.
코인 셀 배터리 장착 경고: 컴퓨터의 내부 작업을 시작하기 전에 컴퓨터와 함께 제공된 안전 정보 를 읽고 컴퓨터 내부에서 작업하기 전에의 단계를 따르십시오. 컴퓨터 내부 작업 후에는 컴퓨터에 내부에서 작업한 후에의 단계를 따르십시오. 안전 모 범 사례에 대한 자세한 내용은 www.dell.com/regulatory_compliance의 규정 준수 홈페이지를 참고하십시오. 절차 양극 방향이 위로 향하도록 하여 코인 셀 배터리를 배터리 소켓에 삽입한 후 아래 로 눌러 제자리에 맞춥니다. 작업후 필수 조건 1 후면 덮개를 장착합니다. 2 스탠드 조립품을 장착합니다.
마이크 분리 경고: 컴퓨터의 내부 작업을 시작하기 전에 컴퓨터와 함께 제공된 안전 정보 를 읽고 컴퓨터 내부에서 작업하기 전에의 단계를 따르십시오. 컴퓨터 내부 작업 후에는 컴퓨터에 내부에서 작업한 후에의 단계를 따르십시오. 안전 모 범 사례에 대한 자세한 내용은 www.dell.com/regulatory_compliance의 규정 준수 홈페이지를 참고하십시오. 전제조건 1 스탠드 조립품을 분리합니다. 2 후면 덮개를 분리합니다. 절차 1 시스템 보드에서 마이크 및 카메라 케이블을 분리합니다. 2 마이크 및 카메라 케이블 배선을 기록해 두고 디스플레이 조립품 베이스의 해당 라우팅 가이드에서 케이블을 분리합니다. 3 "카메라 분리"의 4단계부터 7단계를 수행합니다. 4 마이크를 일정한 각도로 들어 올려 디스플레이 베젤에서 분리합니다.
5 마이크로폰 보드에서 마이크 및 카메라 케이블을 분리합니다.
마이크 장착 경고: 컴퓨터의 내부 작업을 시작하기 전에 컴퓨터와 함께 제공된 안전 정보 를 읽고 컴퓨터 내부에서 작업하기 전에의 단계를 따르십시오. 컴퓨터 내부 작업 후에는 컴퓨터에 내부에서 작업한 후에의 단계를 따르십시오. 안전 모 범 사례에 대한 자세한 내용은 www.dell.com/regulatory_compliance의 규정 준수 홈페이지를 참고하십시오. 절차 1 마이크 및 카메라 케이블을 마이크로폰 보드에 연결합니다. 2 마이크로폰 보드를 디스플레이 베젤의 슬롯에 장착합니다. 3 "카메라 교체"의 1단계부터 3단계를 수행합니다. 4 디스플레이 조립품 베이스의 배선 가이드를 통해 마이크 및 카메라 케이블을 배선합니다. 5 마이크 및 카메라 케이블을 시스템 보드에 연결합니다. 작업후 필수 조건 1 후면 덮개를 장착합니다. 2 스탠드 조립품을 장착합니다.
카메라 분리 경고: 컴퓨터의 내부 작업을 시작하기 전에 컴퓨터와 함께 제공된 안전 정보 를 읽고 컴퓨터 내부에서 작업하기 전에의 단계를 따르십시오. 컴퓨터 내부 작업 후에는 컴퓨터에 내부에서 작업한 후에의 단계를 따르십시오. 안전 모 범 사례에 대한 자세한 내용은 www.dell.com/regulatory_compliance의 규정 준수 홈페이지를 참고하십시오. 전제조건 1 스탠드 조립품을 분리합니다. 2 후면 덮개를 분리합니다. 절차 1 시스템 보드에서 마이크 및 카메라 케이블을 분리합니다. 2 마이크 및 카메라 케이블 배선을 기록해 두고 디스플레이 조립품 베이스의 해당 라우팅 가이드에서 케이블을 분리합니다. 3 "마이크 분리"의 4단계부터 6단계를 수행합니다. 4 손가락 끝으로 고정 클립을 누르고 카메라 모듈을 들어 올립니다. 5 카메라 모듈을 디스플레이 베젤의 카메라 모듈 슬롯에 있는 탭에서 분리합니 다. 6 카메라 모듈을 들어 올려 디스플레이 베젤에서 분리합니다.
7 48 카메라 모듈에서 마이크 및 카메라 케이블을 분리합니다.
카메라 장착 경고: 컴퓨터의 내부 작업을 시작하기 전에 컴퓨터와 함께 제공된 안전 정보 를 읽고 컴퓨터 내부에서 작업하기 전에의 단계를 따르십시오. 컴퓨터 내부 작업 후에는 컴퓨터에 내부에서 작업한 후에의 단계를 따르십시오. 안전 모 범 사례에 대한 자세한 내용은 www.dell.com/regulatory_compliance의 규정 준수 홈페이지를 참고하십시오. 절차 1 마이크 및 카메라 케이블을 카메라 모듈에 연결합니다. 2 카메라 모듈의 탭을 카메라 모듈 슬롯의 탭 안쪽으로 누릅니다. 3 카메라 모듈을 디스플레이 베젤의 슬롯에 눌러 넣고 제자리에 고정될 때까 지. 4 "마이크 교체"의 1단계부터 2단계를 수행합니다. 5 디스플레이 조립품 베이스의 배선 가이드를 통해 마이크 및 카메라 케이블을 배선합니다. 6 마이크 및 카메라 케이블을 시스템 보드에 연결합니다. 작업후 필수 조건 1 후면 덮개를 장착합니다. 2 스탠드 조립품을 장착합니다.
시스템 보드 제거 경고: 컴퓨터의 내부 작업을 시작하기 전에 컴퓨터와 함께 제공된 안전 정보 를 읽고 컴퓨터 내부에서 작업하기 전에의 단계를 따르십시오. 컴퓨터 내부 작업 후에는 컴퓨터에 내부에서 작업한 후에의 단계를 따르십시오. 안전 모 범 사례에 대한 자세한 내용은 www.dell.com/regulatory_compliance의 규정 준수 홈페이지를 참고하십시오. 노트: 사용중인 컴퓨터의 서비스 태그는 시스템 보드에 저장되어 있습니다. 시스템 보드를 교체한 후에 BIOS에 서비스 태그를 반드시 입력해야 합니다. 노트: 시스템 보드를 교체하면 시스템 설정을 사용하여 변경된 BIOS 변경사 항이 모두 제거됩니다. BIOS 설치 프로그램에 다시 만들어야 합니다. 시스 템 보드를 교체한 후 원하는 대로 변경합니다. 노트: 시스템 보드에서 케이블을 분리하기 전에 커넥터의 위치를 기록하여 시스템 보드를 교체한 후에 정확하게 다시 연결할 수 있도록 합니다. 전제조건 1 스탠드 조립품을 분리합니다.
3 4 래치를 들어 올리고 시스템 보드의 커넥터에서 디스플레이 백라이트 케이블 을 분리합니다. 1 스피커 케이블 2 터치 컨트롤 보드 케이블 3 제어 버튼 보드 케이블 4 디스플레이 백라이트 케이 블 5 디스플레이 케이블 6 디스플레이 조립품 베이스 7 하드 드라이브 데이터 케이블 8 광학 드라이브 데이터 케이 블 9 하드 드라이브 및 광학 드라 이브 전원 케이블 10 팬 케이블 11 마이크 및 카메라 케이블 시스템 보드를 디스플레이 조립품 베이스에 고정시키는 나사를 분리합니다.
5 시스템 보드를 안쪽 모서리에서부터 조심스럽게 들어 올린 후 포트를 디스플 레이 조립품 베이스의 슬롯에서 분리합니다. 6 시스템 보드를 디스플레이 조립품 베이스에서 들어 올립니다.
시스템 보드 장착 경고: 컴퓨터의 내부 작업을 시작하기 전에 컴퓨터와 함께 제공된 안전 정보 를 읽고 컴퓨터 내부에서 작업하기 전에의 단계를 따르십시오. 컴퓨터 내부 작업 후에는 컴퓨터에 내부에서 작업한 후에의 단계를 따르십시오. 안전 모 범 사례에 대한 자세한 내용은 www.dell.com/regulatory_compliance의 규정 준수 홈페이지를 참고하십시오. 노트: 사용중인 컴퓨터의 서비스 태그는 시스템 보드에 저장되어 있습니다. 시스템 보드를 교체한 후에 BIOS에 서비스 태그를 반드시 입력해야 합니다. 노트: 시스템 보드를 교체하면 시스템 설정을 사용하여 변경된 BIOS 변경사 항이 모두 제거됩니다. BIOS 설치 프로그램에 다시 만들어야 합니다. 시스 템 보드를 교체한 후 원하는 대로 변경합니다. 절차 1 시스템 보드의 포트를 디스플레이 조립품 베이스의 슬롯에 밀어 넣고 시스템 보드를 디스플레이 조립품 베이스에 올려 놓습니다.
VESA 장착 브래킷 분리 경고: 컴퓨터의 내부 작업을 시작하기 전에 컴퓨터와 함께 제공된 안전 정보 를 읽고 컴퓨터 내부에서 작업하기 전에의 단계를 따르십시오. 컴퓨터 내부 작업 후에는 컴퓨터에 내부에서 작업한 후에의 단계를 따르십시오. 안전 모 범 사례에 대한 자세한 내용은 www.dell.com/regulatory_compliance의 규정 준수 홈페이지를 참고하십시오. 전제조건 1 스탠드 조립품을 분리합니다. 2 후면 덮개를 분리합니다. 절차 1 VESA 장착 브래킷 아래의 스피커 케이블 배선을 기록하고 라우팅 가이드에 서 분리합니다. 2 VESA 장착 브래킷을 디스플레이 조립품 베이스에 고정하는 나사를 분리합니 다.
3 VESA 장착 브래킷을 들어 올려 디스플레이 조립품 베이스에서 분리합니다.
VESA 장착 브래킷 장착 경고: 컴퓨터의 내부 작업을 시작하기 전에 컴퓨터와 함께 제공된 안전 정보 를 읽고 컴퓨터 내부에서 작업하기 전에의 단계를 따르십시오. 컴퓨터 내부 작업 후에는 컴퓨터에 내부에서 작업한 후에의 단계를 따르십시오. 안전 모 범 사례에 대한 자세한 내용은 www.dell.com/regulatory_compliance의 규정 준수 홈페이지를 참고하십시오. 절차 1 VESA 장착 브래킷의 나사 구멍을 디스플레이 조립품 베이스의 나사 구멍에 맞춥니다. 2 VESA 장착 브래킷을 디스플레이 조립품 베이스에 고정하는 나사를 장착합니 다. 3 VESA 장착 브래킷 아래의 배선 가이드를 통해 스피커 케이블을 배선합니다. 작업후 필수 조건 1 후면 덮개를 장착합니다. 2 스탠드 조립품을 장착합니다.
스피커 덮개 분리 경고: 컴퓨터의 내부 작업을 시작하기 전에 컴퓨터와 함께 제공된 안전 정보 를 읽고 컴퓨터 내부에서 작업하기 전에의 단계를 따르십시오. 컴퓨터 내부 작업 후에는 컴퓨터에 내부에서 작업한 후에의 단계를 따르십시오. 안전 모 범 사례에 대한 자세한 내용은 www.dell.com/regulatory_compliance의 규정 준수 홈페이지를 참고하십시오. 전제조건 1 스탠드 조립품을 분리합니다. 2 후면 덮개를 분리합니다. 절차 1 스피커 덮개를 디스플레이 조립품 베이스에 고정시키는 나사를 제거합니다. 2 손가락 끝으로 디스플레이 조립품 베이스에서 스피커 덮개를 살짝 들어 올립 니다.
3 58 스피커 덮개를 들어 올려 디스플레이 베젤에서 분리합니다.
스피커 덮개 장착 경고: 컴퓨터의 내부 작업을 시작하기 전에 컴퓨터와 함께 제공된 안전 정보 를 읽고 컴퓨터 내부에서 작업하기 전에의 단계를 따르십시오. 컴퓨터 내부 작업 후에는 컴퓨터에 내부에서 작업한 후에의 단계를 따르십시오. 안전 모 범 사례에 대한 자세한 내용은 www.dell.com/regulatory_compliance의 규정 준수 홈페이지를 참고하십시오. 절차 1 스피커 덮개의 나사 구멍을 디스플레이 조립품 베이스의 나사 구멍에 맞추고 스피커 덮개를 제자리에 끼웁니다. 2 스피커 덮개를 디스플레이 조립품 베이스에 고정시키는 나사를 장착합니다. 작업후 필수 조건 1 후면 덮개를 장착합니다. 2 스탠드 조립품을 장착합니다.
스피커 분리 경고: 컴퓨터의 내부 작업을 시작하기 전에 컴퓨터와 함께 제공된 안전 정보 를 읽고 컴퓨터 내부에서 작업하기 전에의 단계를 따르십시오. 컴퓨터 내부 작업 후에는 컴퓨터에 내부에서 작업한 후에의 단계를 따르십시오. 안전 모 범 사례에 대한 자세한 내용은 www.dell.com/regulatory_compliance의 규정 준수 홈페이지를 참고하십시오. 전제조건 1 스탠드 조립품을 분리합니다. 2 후면 덮개를 분리합니다. 3 스피커 덮개를 분리합니다. 절차 1 시스템 보드에서 스피커 케이블을 분리합니다. 2 디스플레이 패널 베이스의 스피커 케이블 배선 경로를 기록합니다. 3 스피커 케이블을 일정한 각도로 VESA 장착 브래킷에서 분리합니다. 4 VESA 장착 브래킷에서 나사를 분리합니다. 5 스피커 케이블을 VESA 장착 브래킷에 고정시키는 테이프를 떼어냅니다.
7 스피커와 케이블을 함께 들어 올려 디스플레이 베젤에서 분리합니다.
스피커 장착 경고: 컴퓨터의 내부 작업을 시작하기 전에 컴퓨터와 함께 제공된 안전 정보 를 읽고 컴퓨터 내부에서 작업하기 전에의 단계를 따르십시오. 컴퓨터 내부 작업 후에는 컴퓨터에 내부에서 작업한 후에의 단계를 따르십시오. 안전 모 범 사례에 대한 자세한 내용은 www.dell.com/regulatory_compliance의 규정 준수 홈페이지를 참고하십시오. 절차 1 디스플레이 베젤의 정렬 포스트 및 고무 그로밋을 사용해 스피커를 디스플레 이 베젤에 둡니다. 2 디스플레이 베젤의 배선 가이드를 통해 스피커 케이블을 배선합니다. 3 스피커 케이블을 VESA 장착 브래킷에 고정시키는 테이프를 부착합니다. 4 VESA 장착 브래킷에 나사를 장착합니다. 5 스피커를 장착하는 동안 스피커가 위로 밀리는 경우 고무 그로밋을 장착합니 다. 6 디스플레이 패널 베이스에서 왼쪽 스피커를 오른쪽 스피커에 연결하는 스피 커 케이블을 배선합니다.
제어 버튼 보드 분리 경고: 컴퓨터의 내부 작업을 시작하기 전에 컴퓨터와 함께 제공된 안전 정보 를 읽고 컴퓨터 내부에서 작업하기 전에의 단계를 따르십시오. 컴퓨터 내부 작업 후에는 컴퓨터에 내부에서 작업한 후에의 단계를 따르십시오. 안전 모 범 사례에 대한 자세한 내용은 www.dell.com/regulatory_compliance의 규정 준수 홈페이지를 참고하십시오. 전제조건 1 스탠드 조립품을 분리합니다. 2 후면 덮개를 분리합니다. 3 VESA 장착 브래킷을 분리합니다. 절차 1 래치를 들어 올리고 시스템 보드에서 제어 버튼 보드를 분리합니다. 2 제어 버튼 보드 케이블의 배선 경로를 기록하고 및 디스플레이 조립품 베이 스의 라우팅 가이드에서 케이블을 분리합니다. 3 손끝을 이용해 제어 버튼 보드 슬롯의 고정 클립을 누릅니다. 4 제어 버튼 보드를 들어 올려 디스플레이 베젤에서 분리합니다.
5 64 래치를 들어 올리고 제어 버튼 보드에서 제어 버튼 보드 케이블을 분리합니 다.
제어 버튼 보드 장착 경고: 컴퓨터의 내부 작업을 시작하기 전에 컴퓨터와 함께 제공된 안전 정보 를 읽고 컴퓨터 내부에서 작업하기 전에의 단계를 따르십시오. 컴퓨터 내부 작업 후에는 컴퓨터에 내부에서 작업한 후에의 단계를 따르십시오. 안전 모 범 사례에 대한 자세한 내용은 www.dell.com/regulatory_compliance의 규정 준수 홈페이지를 참고하십시오. 절차 1 제어 버튼 보드 케이블을 제어 버튼 보드의 커넥터에 밀어넣고 래치를 눌러 케이블을 고정합니다. 2 제어 버튼 보드를 디스플레이 베젤의 슬롯에 장착합니다. 3 배선 라우팅 가이드를 통해 제어 버튼 보드 케이블을 배선하고 제어 버튼 보 드 케이블을 디스플레이 조립품 베이스에 부착합니다. 4 제어 버튼 보드 케이블을 시스템 보드의 커넥터에 밀어넣고 래치를 눌러 케 이블을 고정합니다. 작업후 필수 조건 1 VESA 장착 브래킷을 장착합니다. 2 후면 덮개를 장착합니다. 3 스탠드 조립품을 장착합니다.
디스플레이 조립품 분리 경고: 컴퓨터의 내부 작업을 시작하기 전에 컴퓨터와 함께 제공된 안전 정보 를 읽고 컴퓨터 내부에서 작업하기 전에의 단계를 따르십시오. 컴퓨터 내부 작업 후에는 컴퓨터에 내부에서 작업한 후에의 단계를 따르십시오. 안전 모 범 사례에 대한 자세한 내용은 www.dell.com/regulatory_compliance의 규정 준수 홈페이지를 참고하십시오. 전제조건 1 스탠드 조립품을 분리합니다. 2 후면 덮개를 분리합니다. 3 광학 드라이브를 분리합니다. 4 하드 드라이브를 분리합니다. 5 메모리 모듈을 분리합니다. 6 무선 카드를 분리합니다. 7 방열판을 분리합니다. 8 팬을 분리합니다. 9 마이크를 분리합니다. 10 카메라를 분리합니다. 11 시스템 보드를 분리합니다. 12 VESA 장착 브래킷을 분리합니다. 13 스피커 덮개를 분리합니다. 14 스피커를 분리합니다. 15 제어 버튼 보드를 분리합니다.
절차 1 광학 드라이브 및 하드 드라이브 케이블의 배선을 기록하고 디스플레이 조립 품 베이스의 라우팅 가이드에서 케이블을 제거합니다.
2 디스플레이 조립품 베이스를 디스플레이 베젤에 고정하는 나사를 분리합니 다. 1 나사(19개) 2 디스플레이 조립품 베이스 3 디스플레이 패널 베이스를 디스플레이 베젤의 탭에서 분리합니다. 4 디스플레이 케이블을 디스플레이 조립품 베이스의 슬롯을 통해 밀어 넣습니 다.
5 디스플레이 조립품 베이스를 디스플레이 패널에서 들어 올립니다.
1 70 디스플레이 조립품
디스플레이 조립품 장착 경고: 컴퓨터의 내부 작업을 시작하기 전에 컴퓨터와 함께 제공된 안전 정보 를 읽고 컴퓨터 내부에서 작업하기 전에의 단계를 따르십시오. 컴퓨터 내부 작업 후에는 컴퓨터에 내부에서 작업한 후에의 단계를 따르십시오. 안전 모 범 사례에 대한 자세한 내용은 www.dell.com/regulatory_compliance의 규정 준수 홈페이지를 참고하십시오. 절차 1 디스플레이 케이블을 디스플레이 조립품 베이스의 슬롯을 통해 밀어 넣습니 다. 2 디스플레이 베젤의 탭을 디스플레이 조립품 베이스에 있는 슬롯에 밀어 넣습 니다. 3 디스플레이 베젤에 디스플레이 조립품 베이스를 장착합니다. 4 디스플레이 조립품 베이스를 디스플레이 베젤에 고정하는 나사를 장착합니 다. 5 광학 드라이브 및 하드 드라이브 케이블을 디스플레이 조립품 베이스의 라우 팅 가이드를 통해 배선합니다. 작업후 필수 조건 1 제어 버튼 보드를 장착합니다. 2 스피커를 장착합니다.
14 후면 덮개를 장착합니다. 15 스탠드 조립품을 장착합니다.
고무 다리 분리 경고: 컴퓨터의 내부 작업을 시작하기 전에 컴퓨터와 함께 제공된 안전 정보 를 읽고 컴퓨터 내부에서 작업하기 전에의 단계를 따르십시오. 컴퓨터 내부 작업 후에는 컴퓨터에 내부에서 작업한 후에의 단계를 따르십시오. 안전 모 범 사례에 대한 자세한 내용은 www.dell.com/regulatory_compliance의 규정 준수 홈페이지를 참고하십시오. 전제조건 1 스탠드 조립품을 분리합니다. 2 후면 덮개를 분리합니다. 3 광학 드라이브를 분리합니다. 4 하드 드라이브를 분리합니다. 5 메모리 모듈을 분리합니다. 6 무선 카드를 분리합니다. 7 방열판을 분리합니다. 8 팬을 분리합니다. 9 마이크를 분리합니다. 10 카메라를 분리합니다. 11 시스템 보드를 분리합니다. 12 VESA 장착 브래킷을 분리합니다. 13 스피커 덮개를 분리합니다. 14 스피커를 분리합니다. 15 제어 버튼 보드를 분리합니다. 16 디스플레이 어셈블리를 분리합니다.
2 74 디스플레이 베젤에서 고무 다리를 들어 올립니다.
고무 다리 장착 경고: 컴퓨터의 내부 작업을 시작하기 전에 컴퓨터와 함께 제공된 안전 정보 를 읽고 컴퓨터 내부에서 작업하기 전에의 단계를 따르십시오. 컴퓨터 내부 작업 후에는 컴퓨터에 내부에서 작업한 후에의 단계를 따르십시오. 안전 모 범 사례에 대한 자세한 내용은 www.dell.com/regulatory_compliance의 규정 준수 홈페이지를 참고하십시오. 절차 1 고무 다리의 나사 구멍을 디스플레이 베젤의 나사 구멍에 맞춥니다. 2 스피커 덮개를 디스플레이 베젤에 고정시키는 나사를 장착합니다. 작업후 필수 조건 1 디스플레이 어셈블리를 장착합니다. 2 제어 버튼 보드를 장착합니다. 3 스피커를 장착합니다. 4 스피커 덮개를 장착합니다. 5 VESA 장착 브래킷을 장착합니다. 6 시스템 보드를 장착합니다. 7 카메라를 장착합니다. 8 마이크를 장착합니다. 9 팬을 장착합니다. 10 방열판을 장착합니다. 11 무선 카드를 장착합니다.
BIOS 플래싱 사용 가능한 업데이트가 있거나 시스템 보드 교체 후 BIOS를 플래싱(업데이트)해 야 할 수 있습니다. 1 컴퓨터의 전원을 켭니다. 2 www.dell.com/support로 이동합니다. 3 제품 지원을 클릭해 제품의 서비스 태그를 입력한 후 Submit(제출)을 클릭합 니다. 노트: 서비스 태그가 없는 경우 수동으로 자동 검색 기능을 사용하여 컴 퓨터 모델을 찾습니다. 4 Drivers & Downloads(드라이버 및 다운로드)를 클릭합니다. 5 컴퓨터에 설치된 운영 체제를 선택합니다. 6 페이지를 아래로 스크롤하여 BIOS를 확장할 수 있습니다. 7 Download File(파일 다운로드)을 클릭하여 컴퓨터 BIOS의 최신 버전을 다운 로드합니다. 8 다운로드가 완료된 후 파일을 저장하고, BIOS 업데이트 파일을 저장한 폴더 로 이동합니다. 9 BIOS 업데이트 파일 아이콘을 두 번 클릭하고 화면의 지침을 따릅니다.