Inspiron 3583 서비스 매뉴얼 규정 모델: P75F 규정 유형: P75F106 7월 2021년 개정 A02
참고, 주의 및 경고 노트: 참고"는 제품을 보다 효율적으로 사용하는 데 도움이 되는 중요 정보를 제공합니다. 주의: 주의사항은 하드웨어의 손상 또는 데이터 유실 위험을 설명하며, 이러한 문제를 방지할 수 있는 방법을 알려줍니다. 경고: 경고는 재산 손실, 신체적 상해 또는 사망 위험이 있음을 알려줍니다. © 2018-2021 Dell Inc. or its subsidiaries. All rights reserved. Dell, EMC 및 기타 상표는 Dell Inc. 또는 그 자회사의 상표입니다. 다른 상표는 해당 소유자의 상표일 수 있습니다.
목차 장 1: 컴퓨터 내부 작업을 시작하기 전에............................................................................................... 9 시작하기 전에 ...................................................................................................................................................................... 9 장 2: 컴퓨터 내부 작업을 마친 후에....................................................................................................10 장 3: 안전 지침.............................................................................
절차.......................................................................................................................................................................................29 작업후 필수 조건................................................................................................................................................................29 장 14: 코인 셀 배터리 분리............................................................................................................... 30 필수 구성 요소............
장 25: 스피커 장착..........................................................................................................................46 절차.......................................................................................................................................................................................46 작업후 필수 조건................................................................................................................................................................46 장 26: 방열판 분리...
장 36: 시스템 보드 제거.................................................................................................................. 66 필수 구성 요소....................................................................................................................................................................66 절차.......................................................................................................................................................................................66 장 37: 시스템 보드 장착.
작업후 필수 조건................................................................................................................................................................84 장 48: 디스플레이 힌지 분리............................................................................................................ 85 필수 구성 요소....................................................................................................................................................................85 절차..................................
F12 원타임 부팅 메뉴에서 BIOS 업데이트...............................................................................................................99 장 56: 문제 해결............................................................................................................................101 부풀어 오른 리튬 이온 배터리 취급...............................................................................................................................101 SupportAssist 진단....................................................................
1 컴퓨터 내부 작업을 시작하기 전에 노트: 이 문서의 이미지는 주문한 컴퓨터의 구성에 따라 조금씩 다를 수 있습니다. 시작하기 전에 1. 열려 있는 파일을 모두 저장하고 닫은 다음 사용 중인 응용 프로그램을 모두 종료합니다. 2. 컴퓨터를 종료하십시오. Start(시작) > Power(전원) > Shut down(종료)을 클릭합니다. 노트: 다른 운영 체제를 사용하고 있는 경우 해당 운영 체제의 설명서에서 종료 지침을 참조하십시오. 3. 컴퓨터 및 모든 연결된 장치를 전원 콘센트에서 분리하십시오. 4. 키보드, 마우스, 모니터 등과 같은 연결된 모든 네트워크 기기와 주변 장치를 컴퓨터에서 분리합니다. 5. 해당하는 경우, 모든 미디어 카드 및 광학 디스크를 컴퓨터에서 분리합니다.
2 컴퓨터 내부 작업을 마친 후에 주의: 컴퓨터 내부에 나사가 남아 있거나 느슨한 나사가 존재하는 경우 컴퓨터가 심각하게 손상될 수 있습니다. 1. 나사를 모두 장착하고 컴퓨터 내부에 남아 있는 나사가 없는지 확인합니다. 2. 컴퓨터 작업을 시작하기 전에 분리한 모든 외부 장치, 주변 장치 및 케이블을 컴퓨터에 연결합니다. 3. 컴퓨터 작업을 시작하기 전에 분리한 모든 미디어 카드, 디스크 및 기타 부품을 다시 장착합니다. 4. 전원 콘센트에 컴퓨터와 연결된 모든 장치를 연결합니다. 5. 컴퓨터를 켭니다.
3 안전 지침 컴퓨터의 손상을 방지하고 안전하게 작업하기 위해 다음 안전 지침을 따르십시오. 달리 명시되지 않는 한, 본 문서에 포함된 각 절차 에서는 컴퓨터와 함께 제공된 안전 정보를 읽었음을 전제로 설명합니다. 경고: 컴퓨터 내부 작업을 시작하기 전에 컴퓨터와 함께 제공된 안전 정보를 읽고 숙지하십시오. 추가 안전 모범 사례는 Regulatory Compliance(규정 준수) 홈페이지(www.dell.com/regulatory_compliance)를 참조하십시오. 경고: 컴퓨터 커버 및 패널을 열기 전에 모든 전원에서 컴퓨터를 연결 해제합니다. 컴퓨터 내부에서 작업한 후 컴퓨터를 전기 콘 센트에 연결하기 전에 커버, 패널 및 나사를 모두 장착합니다. 주의: 컴퓨터의 손상을 방지하려면 작업 표면이 평평하고 건조하고 깨끗한지 확인합니다. 주의: 구성 요소 및 카드의 손상을 방지하려면 구성 요소 및 카드의 핀이나 단자를 잡지 말고 모서리를 잡습니다.
● 접지 처리가 제대로 된 유선 ESD 손목 접지대를 사용하십시오. 무선 정전기 방지 스트랩은 정전기 방지 기능이 충분하지 않기 때 문에 더 이상 사용할 수 없습니다. 부품을 처리하기 전에 섀시를 건드리면 ESD 손상에 대한 민감도가 증가하여 부품에 적절한 ESD 보호를 제공하지 않습니다. ● 정전기 방지 공간에서 정전기에 민감한 구성 요소를 다룹니다. 가능하면 정전기 방지 바닥 패드와 작업 패드를 사용하십시오. ● 정전기에 민감한 구성 요소의 포장을 푸는 경우, 부품 설치 준비를 한 후 정전기 방지 포장재에서 제품을 꺼내십시오. 정전기 방지 패키징을 풀려면 먼저 몸에 있는 정전기를 모두 제거해야 합니다. ● 정전기에 민감한 구성 요소를 운반하기 전에 정전기 방지 용기나 포장재에 넣습니다. ESD 현장 서비스 키트 모니터링되지 않는 현장 서비스 키트는 가장 일반적으로 사용되는 서비스 키트입니다.
민감한 구성요소 운반 교체용 부품이나 Dell에 반품할 부품과 같이 ESD에 민감한 장치를 운반할 때는 정전기 방지 백에 넣어 운반하는 것이 안전합니다. 장비 들어 올리기 무거운 장비를 들어 올릴 때는 다음 지침을 따르십시오. 주의: 50파운드보다 무거운 장비를 들어 올리지 마십시오. 항상 다른 사람에게 도움을 요청하거나 기계 인양 장치를 사용하십시 오. 1. 2. 3. 4. 5. 6. 발을 바닥에 안정적으로 딛습니다. 발 사이를 벌려서 안정적인 자세를 취하고 발가락을 바깥쪽으로 향합니다. 배에 힘을 줍니다. 장비를 들어 올릴 때 배의 근육이 허리를 받쳐주어 장비 무게의 균형을 조절할 수 있습니다. 허리가 아닌 다리를 사용하여 들어 올립니다. 장비에 몸을 바짝 붙입니다. 허리 쪽에 가까이 붙일수록 허리에 가해지는 부담이 줄어듭니다. 장비를 들어 올리든 내려 놓든 허리를 바로 세웁니다. 몸의 무게를 장비에 싣지 않습니다. 몸과 등을 비틀지 않습니다. 장비를 내릴 때에는 이 지침의 역순을 따르십시오.
4 권장 도구 이 문서의 절차를 수행하기 위해 다음 도구가 필요할 수 있습니다.
5 나사 목록 노트: 구성 요소에서 나사를 제거할 때 나사 유형과 나사 수량을 적어둔 후 나사 보관함에 보관하는 것이 좋습니다. 이렇게 하면 구성 요소를 장착할 때 정확한 나사 개수와 올바른 나사 유형으로 복원할 수 있습니다. 노트: 일부 컴퓨터에는 자기 표면이 있습니다. 구성 요소를 교체할 때 나사를 이러한 표면에 부착된 채로 남겨두지 않아야 합니 다. 노트: 나사 색상은 주문한 구성에 따라 달라질 수 있습니다. 표 1. 나사 목록 구성 요소 고정 위치 나사 유형 수량 베이스 커버 팜레스트 및 키보드 어셈 블리 M2x2 2 베이스 커버 팜레스트 및 키보드 어셈 블리 M2x4 1 베이스 커버 팜레스트 및 키보드 어셈 블리 M2.5x7 6 나사 이미지 노트: 나사 색은 주문한 구성에 따라 다를 수 있 습니다.
표 1. 나사 목록 (계속) 구성 요소 고정 위치 나사 유형 수량 전원 어댑터 포트 팜레스트 및 키보드 어셈 블리 M2x3 1 전원 버튼 보드 팜레스트 및 키보드 어셈 블리 M2x2 1 지문 인식기가 장착된 전 원 버튼(선택 사항) 팜레스트 및 키보드 어셈 블리 M2x2 1 솔리드 스테이트 드라이 브/인텔 옵테인 팜레스트 및 키보드 어셈 블리 M2x2.
6 베이스 덮개 분리 노트: 컴퓨터 내부에서 작업하기 전에 컴퓨터와 함께 제공된 안전 정보를 읽어 보고 컴퓨터 내부 작업을 시작하기 전에의 단계를 따르십시오. 컴퓨터 내부 작업을 마친 후에 컴퓨터 내부 작업을 마친 후에의 지침을 따르십시오. 추가 안전 모범 사례는 Regulatory Compliance(규정 준수) 홈페이지(www.dell.com/regulatory_compliance)를 참조하십시오. 절차 1. 베이스 커버에 있는 3개의 조임 나사를 풉니다. 2. 베이스 커버를 손목 받침대 및 키보드 어셈블리에 고정하는 나사(M2x4)를 제거합니다. 3. 베이스 커버를 손목 받침대 및 키보드 어셈블리에 고정하는 6개의 나사(M2.5x7)를 제거합니다. 4. 컴퓨터 베이스의 왼쪽 상단부터 베이스 커버를 살짝 들어 올립니다. 5. 베이스 커버를 들어 올려 손목 받침대 및 키보드 어셈블리에서 분리합니다.
노트: 다음 단계는 컴퓨터에서 기타 구성 요소를 추가로 제거하려는 경우에만 적용됩니다. 6. 시스템 보드에서 배터리 케이블을 분리합니다. 7. 약 5초간 전원 버튼을 눌러 컴퓨터를 접지하고 잔류 전원을 방전시킵니다.
7 베이스 덮개 장착 노트: 컴퓨터 내부에서 작업하기 전에 컴퓨터와 함께 제공된 안전 정보를 읽어 보고 컴퓨터 내부 작업을 시작하기 전에의 단계를 따르십시오. 컴퓨터 내부 작업을 마친 후에 컴퓨터 내부 작업을 마친 후에의 지침을 따르십시오. 추가 안전 모범 사례는 Regulatory Compliance(규정 준수) 홈페이지(www.dell.com/regulatory_compliance)를 참조하십시오. 절차 1. 해당하는 경우, 배터리 케이블을 시스템 보드에 연결합니다. 주의: 전원 어댑터 포트가 실수로 손상되지 않도록 하려면 컴퓨터 베이스에 베이스 커버를 끼울 때 전원 어댑터 포트에 베이 스 커버를 밀어 누르지 마십시오. 2. 베이스 커버를 손목 받침대 및 키보드 어셈블리에 놓습니다. 3. 전원 어댑터 포트에서부터 베이스 커버를 제자리에 끼워 넣습니다. 4. 베이스 커버를 손목 받침대 및 키보드 어셈블리에 고정하는 3개의 조임 나사를 조입니다. 5.
베이스 덮개 장착
8 배터리 분리 노트: 컴퓨터 내부에서 작업하기 전에 컴퓨터와 함께 제공된 안전 정보를 읽어 보고 컴퓨터 내부 작업을 시작하기 전에의 단계를 따르십시오. 컴퓨터 내부 작업을 마친 후에 컴퓨터 내부 작업을 마친 후에의 지침을 따르십시오. 추가 안전 모범 사례는 Regulatory Compliance(규정 준수) 홈페이지(www.dell.com/regulatory_compliance)를 참조하십시오. 리튬 이온 배터리 예방 조치 주의: ● 리튬 이온 배터리를 다룰 때는 주의하십시오. ● 배터리를 제거하기 전에 완전히 방전시키십시오. 시스템에서 AC 전원 어댑터의 연결을 해제하고 배터리 전원으로만 컴퓨터 를 작동시킵니다. 전원 버튼을 눌렀을 때 컴퓨터가 더 이상 켜지지 않으면 배터리가 완전히 방전된 것입니다. ● 배터리를 찌그러뜨리거나 떨어뜨리거나 훼손하거나 외부 개체로 배터리에 구멍을 뚫지 마십시오. ● 고온에 배터리를 노출하거나 배터리 팩과 셀을 분해하지 마십시오.
배터리 분리
9 배터리 장착 노트: 컴퓨터 내부에서 작업하기 전에 컴퓨터와 함께 제공된 안전 정보를 읽어 보고 컴퓨터 내부 작업을 시작하기 전에의 단계를 따르십시오. 컴퓨터 내부 작업을 마친 후에 컴퓨터 내부 작업을 마친 후에의 지침을 따르십시오. 추가 안전 모범 사례는 Regulatory Compliance(규정 준수) 홈페이지(www.dell.com/regulatory_compliance)를 참조하십시오. 리튬 이온 배터리 예방 조치 주의: ● 리튬 이온 배터리를 다룰 때는 주의하십시오. ● 배터리를 제거하기 전에 완전히 방전시키십시오. 시스템에서 AC 전원 어댑터의 연결을 해제하고 배터리 전원으로만 컴퓨터 를 작동시킵니다. 전원 버튼을 눌렀을 때 컴퓨터가 더 이상 켜지지 않으면 배터리가 완전히 방전된 것입니다. ● 배터리를 찌그러뜨리거나 떨어뜨리거나 훼손하거나 외부 개체로 배터리에 구멍을 뚫지 마십시오. ● 고온에 배터리를 노출하거나 배터리 팩과 셀을 분해하지 마십시오.
3. 배터리 케이블을 시스템 보드에 연결합니다. 작업후 필수 조건 베이스 덮개를 장착합니다.
10 메모리 모듈 분리 노트: 컴퓨터 내부에서 작업하기 전에 컴퓨터와 함께 제공된 안전 정보를 읽어 보고 컴퓨터 내부 작업을 시작하기 전에의 단계를 따르십시오. 컴퓨터 내부 작업을 마친 후에 컴퓨터 내부 작업을 마친 후에의 지침을 따르십시오. 추가 안전 모범 사례는 Regulatory Compliance(규정 준수) 홈페이지(www.dell.com/regulatory_compliance)를 참조하십시오. 필수 구성 요소 베이스 덮개를 분리합니다. 절차 1. 컴퓨터에서 메모리 모듈을 찾습니다. 2. 메모리 모듈이 튀어 나올 때까지 메모리 모듈 슬롯의 양쪽 끝에 있는 고정 클립을 손끝으로 조심스럽게 벌립니다. 3. 메모리 모듈 슬롯에서 메모리 모듈을 분리합니다.
11 메모리 모듈 장착 노트: 컴퓨터 내부에서 작업하기 전에 컴퓨터와 함께 제공된 안전 정보를 읽어 보고 컴퓨터 내부 작업을 시작하기 전에의 단계를 따르십시오. 컴퓨터 내부 작업을 마친 후에 컴퓨터 내부 작업을 마친 후에의 지침을 따르십시오. 추가 안전 모범 사례는 Regulatory Compliance(규정 준수) 홈페이지(www.dell.com/regulatory_compliance)를 참조하십시오. 절차 1. 메모리 모듈의 노치를 메모리 모듈 슬롯의 탭에 맞춥니다. 2. 메모리 모듈을 일정한 각도로 슬롯에 단단히 밀어 넣습니다. 3. 딸깍 소리가 나면서 제자리에 고정될 때까지 메모리 모듈을 아래로 누릅니다. 노트: 소리가 나지 않으면 메모리 모듈을 분리했다가 다시 설치합니다. 작업후 필수 조건 베이스 덮개를 장착합니다.
12 무선 카드 분리 노트: 컴퓨터 내부에서 작업하기 전에 컴퓨터와 함께 제공된 안전 정보를 읽어 보고 컴퓨터 내부 작업을 시작하기 전에의 단계를 따르십시오. 컴퓨터 내부 작업을 마친 후에 컴퓨터 내부 작업을 마친 후에의 지침을 따르십시오. 추가 안전 모범 사례는 Regulatory Compliance(규정 준수) 홈페이지(www.dell.com/regulatory_compliance)를 참조하십시오. 필수 구성 요소 베이스 덮개를 분리합니다. 절차 1. 컴퓨터에서 무선 카드를 찾습니다. 2. 무선 카드 브래킷을 시스템 보드에 고정하는 나사(M2x3)를 제거합니다. 3. 무선 카드 브래킷을 밀어 올려 무선 카드 밖으로 빼냅니다. 4. 플라스틱 스크라이브를 사용하여 무선 카드에서 안테나 케이블을 연결 해제합니다. 5. 무선 카드를 밀어서 무선 카드 슬롯 밖으로 빼냅니다.
무선 카드 분리
13 무선 카드 장착 노트: 컴퓨터 내부에서 작업하기 전에 컴퓨터와 함께 제공된 안전 정보를 읽어 보고 컴퓨터 내부 작업을 시작하기 전에의 단계를 따르십시오. 컴퓨터 내부 작업을 마친 후에 컴퓨터 내부 작업을 마친 후에의 지침을 따르십시오. 추가 안전 모범 사례는 Regulatory Compliance(규정 준수) 홈페이지(www.dell.com/regulatory_compliance)를 참조하십시오. 절차 주의: 무선 카드의 손상을 방지하려면 카드 아래에 케이블을 올려 놓지 마십시오. 1. 무선 카드에 안테나 케이블을 연결합니다. 다음 표에는 컴퓨터에서 지원되는 무선 카드의 안테나 케이블 색상표가 제공됩니다. 표 2. 안테나 케이블 색상표 무선 카드의 커넥터 안테나 케이블 색상 주(흰색 삼각형) 흰색 보조(검정색 삼각형) 검정색 2. 무선 카드 브래킷을 밀어서 무선 카드에 장착합니다. 3.
14 코인 셀 배터리 분리 노트: 컴퓨터 내부에서 작업하기 전에 컴퓨터와 함께 제공된 안전 정보를 읽어 보고 컴퓨터 내부 작업을 시작하기 전에의 단계를 따르십시오. 컴퓨터 내부 작업을 마친 후에 컴퓨터 내부 작업을 마친 후에의 지침을 따르십시오. 추가 안전 모범 사례는 Regulatory Compliance(규정 준수) 홈페이지(www.dell.com/regulatory_compliance)를 참조하십시오. 주의: 코인 셀 배터리를 분리하면 BIOS 설정 프로그램 설정을 기본값으로 재설정합니다. 코인 셀 배터리를 제거하기 전에 BIOS 설정 프로그램 설정을 기록하는 것이 좋습니다. 필수 구성 요소 베이스 덮개를 분리합니다. 절차 주의: 코인 셀 배터리를 분리하면 BIOS 설정 프로그램 설정을 기본값으로 재설정합니다. 코인 셀 배터리를 제거하기 전에 BIOS 설정 프로그램의 설정을 기록하는 것이 좋습니다. 절차 1. 코인 셀 배터리 케이블을 I/O 보드에서 연결 해제합니다. 2.
15 코인 셀 배터리 장착 노트: 컴퓨터 내부에서 작업하기 전에 컴퓨터와 함께 제공된 안전 정보를 읽어 보고 컴퓨터 내부 작업을 시작하기 전에의 단계를 따르십시오. 컴퓨터 내부 작업을 마친 후에 컴퓨터 내부 작업을 마친 후에의 지침을 따르십시오. 추가 안전 모범 사례는 Regulatory Compliance(규정 준수) 홈페이지(www.dell.com/regulatory_compliance)를 참조하십시오. 절차 절차 1. 손목 받침대 및 키보드 어셈블리에 코인 셀 배터리를 부착합니다. 2. I/O 보드에 코인 셀 배터리 케이블을 연결합니다. 작업후 필수 조건 베이스 덮개를 장착합니다.
16 팬 분리 노트: 컴퓨터 내부에서 작업하기 전에 컴퓨터와 함께 제공된 안전 정보를 읽어 보고 컴퓨터 내부 작업을 시작하기 전에의 단계를 따르십시오. 컴퓨터 내부 작업을 마친 후에 컴퓨터 내부 작업을 마친 후에의 지침을 따르십시오. 추가 안전 모범 사례는 Regulatory Compliance(규정 준수) 홈페이지(www.dell.com/regulatory_compliance)를 참조하십시오. 필수 구성 요소 베이스 덮개를 분리합니다. 절차 1. 래치를 열고 시스템 보드에서 디스플레이 케이블을 분리합니다. 2. 팬의 라우팅 가이드에서 디스플레이 케이블을 제거합니다. 3. 시스템 보드에서 팬 케이블을 분리합니다. 4. 팬을 손목 받침대 및 키보드 보드 어셈블리에 고정하는 3개의 나사(M2.5x5)를 제거합니다. 5. 팬을 들어 올려 손목 받침대 및 키보드 보드 어셈블리에서 분리합니다.
팬 분리 33
17 팬 장착 노트: 컴퓨터 내부에서 작업하기 전에 컴퓨터와 함께 제공된 안전 정보를 읽어 보고 컴퓨터 내부 작업을 시작하기 전에의 단계를 따르십시오. 컴퓨터 내부 작업을 마친 후에 컴퓨터 내부 작업을 마친 후에의 지침을 따르십시오. 추가 안전 모범 사례는 Regulatory Compliance(규정 준수) 홈페이지(www.dell.com/regulatory_compliance)를 참조하십시오. 절차 1. 팬의 나사 구멍을 손목 받침대 및 키보드 보드 어셈블리의 나사 구멍에 맞춥니다. 2. 팬을 손목 받침대 및 키보드 보드 어셈블리에 고정하는 3개의 나사(M2.5x5)를 장착합니다. 3. 팬 케이블을 시스템 보드에 연결합니다. 4. 팬의 라우팅 가이드를 통해 디스플레이 케이블을 배선합니다. 5. 디스플레이 케이블을 시스템 보드의 커넥터에 연결한 후 래치를 닫아 케이블을 고정합니다. 작업후 필수 조건 베이스 덮개를 장착합니다.
18 솔리드 스테이트 드라이브/인텔 옵테인 제거 컴퓨터에서 인텔 옵테인 디바이스를 제거하기 전에 비활성화해야 합니다. 인텔 옵테인 디바이스 비활성화에 대한 자세한 정보는 인 텔 옵테인 메모리 비활성화를 참조하십시오. 노트: 컴퓨터 내부에서 작업하기 전에 컴퓨터와 함께 제공된 안전 정보를 읽어 보고 컴퓨터 내부 작업을 시작하기 전에의 단계를 따르십시오. 컴퓨터 내부 작업을 마친 후에 컴퓨터 내부 작업을 마친 후에의 지침을 따르십시오. 추가 안전 모범 사례는 Regulatory Compliance(규정 준수) 홈페이지(www.dell.com/regulatory_compliance)를 참조하십시오. 필수 구성 요소 베이스 덮개를 분리합니다. 절차 1. 솔리드 스테이트 드라이브 실드/인텔 옵테인 실드 및 솔리드 스테이트 드라이브/인텔 옵테인을 손목 받침대 및 키보드 어셈블리 에 고정하는 2개의 조임 나사를 풉니다.
19 솔리드 스테이트 드라이브/인텔 옵테인 교체 인텔 옵테인 디바이스를 교체한 후 활성화하십시오. 인텔 옵테인 디바이스 활성화에 대한 자세한 정보는 인텔 옵테인 메모리 활성화 를 참조하십시오. 노트: 컴퓨터 내부에서 작업하기 전에 컴퓨터와 함께 제공된 안전 정보를 읽어 보고 컴퓨터 내부 작업을 시작하기 전에의 단계를 따르십시오. 컴퓨터 내부 작업을 마친 후에 컴퓨터 내부 작업을 마친 후에의 지침을 따르십시오. 추가 안전 모범 사례는 Regulatory Compliance(규정 준수) 홈페이지(www.dell.com/regulatory_compliance)를 참조하십시오. 주의: 솔리드 상태 드라이브는 충격에 약합니다. 솔리드 상태 드라이브를 다룰 때는 주의합니다. 절차 1. 솔리드 스테이트 드라이브/인텔 옵테인의 노치를 솔리드 스테이트 드라이브/인텔 옵테인 슬롯의 탭에 맞춥니다. 2. 솔리드 스테이트 드라이브/인텔 옵테인을 솔리드 스테이트 드라이브/인텔 옵테인 슬롯에 밀어 넣습니다. 3.
20 하드 드라이브 분리 컴퓨터가 인텔 옵테인 메모리로 가속되는 SATA 스토리지 장치를 사용 중인 경우 SATA 스토리지 장치를 제거하기 전에 인텔 옵테인 을 비활성화합니다. 인텔 옵테인 비활성화에 대한 자세한 내용은 인텔 옵테인 비활성화를 참조하십시오. 노트: 컴퓨터 내부에서 작업하기 전에 컴퓨터와 함께 제공된 안전 정보를 읽어 보고 컴퓨터 내부 작업을 시작하기 전에의 단계를 따르십시오. 컴퓨터 내부 작업을 마친 후에 컴퓨터 내부 작업을 마친 후에의 지침을 따르십시오. 추가 안전 모범 사례는 Regulatory Compliance(규정 준수) 홈페이지(www.dell.com/regulatory_compliance)를 참조하십시오. 주의: 하드 드라이브는 쉽게 손상될 수 있습니다. 하드 드라이브를 조심스럽게 다룹니다. 주의: 데이터 손실 위험이 있으므로 컴퓨터가 켜져 있거나 절전 모드인 상태에서 하드 드라이브를 분리하지 마십시오. 필수 구성 요소 1. 베이스 덮개를 분리합니다. 2.
5. 하드 드라이브 브래킷을 하드 드라이브에 고정시키는 4개의 나사(M3x3)를 분리합니다. 6. 하드 드라이브 브래킷을 들어 올려 하드 드라이브에서 분리합니다.
21 하드 드라이브 장착 SATA 스토리지를 장착한 후 인텔 옵테인을 활성화합니다. 인텔 옵테인 활성화에 대한 자세한 내용은 인텔 옵테인 활성화를 참조하십 시오. 노트: 컴퓨터 내부에서 작업하기 전에 컴퓨터와 함께 제공된 안전 정보를 읽어 보고 컴퓨터 내부 작업을 시작하기 전에의 단계를 따르십시오. 컴퓨터 내부 작업을 마친 후에 컴퓨터 내부 작업을 마친 후에의 지침을 따르십시오. 추가 안전 모범 사례는 Regulatory Compliance(규정 준수) 홈페이지(www.dell.com/regulatory_compliance)를 참조하십시오. 주의: 하드 드라이브는 쉽게 손상될 수 있습니다. 하드 드라이브를 조심스럽게 다룹니다. 절차 1. 하드 드라이브 브래킷의 나사 구멍을 하드 드라이브의 나사 구멍에 맞춥니다. 2. 하드 드라이브 브래킷을 하드 드라이브에 고정시키는 4개의 나사(M3x3)를 장착합니다. 3. 하드 드라이브 조립품에 인터포저를 연결합니다. 4.
작업후 필수 조건 1. 배터리를 장착합니다. 2. 베이스 덮개를 장착합니다.
22 터치패드 분리 노트: 컴퓨터 내부에서 작업하기 전에 컴퓨터와 함께 제공된 안전 정보를 읽어 보고 컴퓨터 내부 작업을 시작하기 전에의 단계를 따르십시오. 컴퓨터 내부 작업을 마친 후에 컴퓨터 내부 작업을 마친 후에의 지침을 따르십시오. 추가 안전 모범 사례는 Regulatory Compliance(규정 준수) 홈페이지(www.dell.com/regulatory_compliance)를 참조하십시오. 필수 구성 요소 1. 베이스 덮개를 분리합니다. 2. 배터리를 분리합니다. 절차 1. 래치를 열고 시스템 보드에서 하드 드라이브 케이블을 분리합니다. 2. 래치를 열고 시스템 보드에서 터치패드 케이블을 연결 해제합니다. 3. 래치를 열고 시스템 보드에서 키보드 백라이트 케이블을 연결 해제합니다. 4. 터치패드를 손목 받침대 및 키보드 어셈블리에 고정하는 테이프를 조심스럽게 떼어냅니다. 5. 터치패드를 손목 받침대 및 키보드 어셈블리에 고정하는 4개의 나사(M2x2)를 제거합니다. 6.
터치패드 분리
23 터치패드 장착 노트: 컴퓨터 내부에서 작업하기 전에 컴퓨터와 함께 제공된 안전 정보를 읽어 보고 컴퓨터 내부 작업을 시작하기 전에의 단계를 따르십시오. 컴퓨터 내부 작업을 마친 후에 컴퓨터 내부 작업을 마친 후에의 지침을 따르십시오. 추가 안전 모범 사례는 Regulatory Compliance(규정 준수) 홈페이지(www.dell.com/regulatory_compliance)를 참조하십시오. 절차 노트: 터치패드가 손목 받침대 및 키보드 어셈블리의 해당 가이드와 정렬되어 있고 터치패드의 양쪽 간격이 동일한지 확인합니 다. 1. 터치패드를 손목 받침대 및 키보드 어셈블리의 슬롯으로 밀어 넣습니다. 2. 터치패드를 손목 받침대 및 키보드 어셈블리에 고정하는 4개의 나사(M2x2)를 장착합니다. 3. 터치패드를 손목 받침대 및 키보드 어셈블리에 고정하는 테이프를 부착합니다. 4. 하드 드라이브 케이블을 시스템 보드의 커넥터에 밀어넣고 래치를 눌러 케이블을 고정합니다. 5.
작업후 필수 조건 1. 배터리를 장착합니다. 2. 베이스 덮개를 장착합니다.
24 스피커 분리 노트: 컴퓨터 내부에서 작업하기 전에 컴퓨터와 함께 제공된 안전 정보를 읽어 보고 컴퓨터 내부 작업을 시작하기 전에의 단계를 따르십시오. 컴퓨터 내부 작업을 마친 후에 컴퓨터 내부 작업을 마친 후에의 지침을 따르십시오. 추가 안전 모범 사례는 Regulatory Compliance(규정 준수) 홈페이지(www.dell.com/regulatory_compliance)를 참조하십시오. 필수 구성 요소 1. 베이스 덮개를 분리합니다. 2. 솔리드 스테이트 드라이브/인텔 옵테인을 제거합니다. 절차 1. 시스템 보드에서 스피커 케이블을 연결 해제하고 오른쪽 스피커를 들어 올려 손목 받침대 및 키보드 어셈블리에서 분리합니다. 2. 스피커 케이블 라우팅을 기록하고 손목 받침대 및 키보드 어셈블리의 라우팅 가이드에서 케이블을 제거합니다. 3. 왼쪽 스피커와 해당 케이블을 함께 들어 올려 손목 받침대 및 키보드 어셈블리에서 분리합니다.
25 스피커 장착 노트: 컴퓨터 내부에서 작업하기 전에 컴퓨터와 함께 제공된 안전 정보를 읽어 보고 컴퓨터 내부 작업을 시작하기 전에의 단계를 따르십시오. 컴퓨터 내부 작업을 마친 후에 컴퓨터 내부 작업을 마친 후에의 지침을 따르십시오. 추가 안전 모범 사례는 Regulatory Compliance(규정 준수) 홈페이지(www.dell.com/regulatory_compliance)를 참조하십시오. 절차 노트: 스피커 제거 시 고무 그로밋이 빠져나온 상태라면 스피커를 장착하기 전에 제자리에 밀어 넣습니다. 1. 정렬 포스트 및 고무 그로밋을 사용하여 왼쪽 스피커를 손목 받침대 및 키보드 어셈블리의 슬롯에 끼워 넣습니다. 2. 손목 받침대 및 키보드 어셈블리의 라우팅 가이드를 통해 스피커 케이블을 라우팅하고 오른쪽 스피커를 장착합니다. 3. 시스템 보드에 스피커 케이블을 연결합니다. 작업후 필수 조건 1. 솔리드 스테이트 드라이브/인텔 옵테인을 장착합니다. 2. 베이스 덮개를 장착합니다.
26 방열판 분리 노트: 컴퓨터 내부에서 작업하기 전에 컴퓨터와 함께 제공된 안전 정보를 읽어 보고 컴퓨터 내부 작업을 시작하기 전에의 단계를 따르십시오. 컴퓨터 내부 작업을 마친 후에 컴퓨터 내부 작업을 마친 후에의 지침을 따르십시오. 추가 안전 모범 사례는 Regulatory Compliance(규정 준수) 홈페이지(www.dell.com/regulatory_compliance)를 참조하십시오. 노트: 방열판은 정상 작동 중에 뜨거워질 수 있습니다. 충분한 시간 동안 방열판을 식힌 후에 만지도록 하십시오. 주의: 프로세서의 최대 냉각 기능을 보장하려면 프로세서 방열판의 열 전달 영역을 만지지 마십시오. 피부에 묻어있는 오일은 열 그리스의 열 전달 기능을 저하시킬 수 있습니다. 필수 구성 요소 베이스 덮개를 분리합니다. 절차 1. 방열판을 시스템 보드에 고정하는 4개의 조임 나사를 반대 순서로(4>3>2>1) 풉니다. 2. 방열판을 들어 올려 시스템 보드에서 분리합니다.
27 방열판 장착 노트: 컴퓨터 내부에서 작업하기 전에 컴퓨터와 함께 제공된 안전 정보를 읽어 보고 컴퓨터 내부 작업을 시작하기 전에의 단계를 따르십시오. 컴퓨터 내부 작업을 마친 후에 컴퓨터 내부 작업을 마친 후에의 지침을 따르십시오. 추가 안전 모범 사례는 Regulatory Compliance(규정 준수) 홈페이지(www.dell.com/regulatory_compliance)를 참조하십시오. 주의: 방열판을 잘못 맞추면 시스템 보드 및 프로세서가 손상될 수 있습니다. 노트: 시스템 보드 또는 방열판을 장착할 경우 키트에 제공된 방열 패드/붙여넣기를 사용하여 열 전도성을 확보합니다. 절차 1. 방열판을 시스템 보드에 놓고 방열판의 나사 구멍을 시스템 보드의 나사 구멍에 맞춥니다. 2. 방열판에 지정된 번호 순서대로 방열판을 시스템 보드에 고정하는 조임 나사를 조입니다. 작업후 필수 조건 베이스 덮개를 장착합니다.
28 전원 어댑터 포트 분리 노트: 컴퓨터 내부에서 작업하기 전에 컴퓨터와 함께 제공된 안전 정보를 읽어 보고 컴퓨터 내부 작업을 시작하기 전에의 단계를 따르십시오. 컴퓨터 내부 작업을 마친 후에 컴퓨터 내부 작업을 마친 후에의 지침을 따르십시오. 추가 안전 모범 사례는 Regulatory Compliance(규정 준수) 홈페이지(www.dell.com/regulatory_compliance)를 참조하십시오. 디스플레이 조립품 분리 노트: 컴퓨터 내부에서 작업하기 전에 컴퓨터와 함께 제공된 안전 정보를 읽어 보고 컴퓨터 내부 작업을 시작하기 전에의 단계를 따르십시오. 컴퓨터 내부 작업을 마친 후에 컴퓨터 내부 작업을 마친 후에의 지침을 따르십시오. 추가 안전 모범 사례는 Regulatory Compliance(규정 준수) 홈페이지(www.dell.com/regulatory_compliance)를 참조하십시오. 필수 구성 요소 1. 베이스 덮개를 분리합니다. 2. 무선 카드를 분리합니다. 절차 1.
5. 손목 받침대 및 키보드 조립품을 일정 각도로 들어 올립니다. 6. 손목 받침대 및 키보드 어셈블리를 밀어 디스플레이 어셈블리에서 제거합니다. 7. 위의 모든 단계를 수행하고 나면 디스플레이 어셈블리가 남습니다.
절차 1. 오른쪽 힌지를 시스템 보드 및 손목 받침대 어셈블리에 고정하는 3개의 나사(M2.5x5)를 제거합니다. 2. 오른쪽 힌지를 들어 올립니다. 3. 시스템 보드에서 전원 어댑터 포트 케이블을 분리합니다. 4. 전원 어댑터 포트 케이블 배선을 기록하고 손목 받침대 및 키보드 조립품의 라우팅 가이드에서 분리합니다. 5. 전원 어댑터 포트를 손목 받침대 및 키보드 어셈블리에 고정하는 나사(M2x2)를 제거합니다. 6. 전원 어댑터 포트 및 해당 케이블을 함께 들어 올려 손목 받침대 및 키보드 조립품에서 분리합니다.
29 전원 어댑터 포트 장착 노트: 컴퓨터 내부에서 작업하기 전에 컴퓨터와 함께 제공된 안전 정보를 읽어 보고 컴퓨터 내부 작업을 시작하기 전에의 단계를 따르십시오. 컴퓨터 내부 작업을 마친 후에 컴퓨터 내부 작업을 마친 후에의 지침을 따르십시오. 추가 안전 모범 사례는 Regulatory Compliance(규정 준수) 홈페이지(www.dell.com/regulatory_compliance)를 참조하십시오. 절차 1. 전원 어댑터 포트의 나사 구멍을 손목 받침대 및 키보드 조립품의 나사 구멍에 맞춥니다. 2. 전원 어댑터 포트를 손목 받침대 및 키보드 어셈블리에 고정하는 나사(M2x2)를 장착합니다. 3. 손목 받침대 및 키보드 조립품의 라우팅 가이드를 통해 전원 어댑터 포트 케이블을 배선합니다. 4. 전원 어댑터 포트 케이블을 시스템 보드에 연결합니다. 5. 오른쪽 힌지를 닫습니다. 6. 오른쪽 힌지를 시스템 보드 및 손목 받침대 어셈블리에 고정하는 3개의 나사(M2.5x5)를 장착합니다.
3. 정렬 포스트를 사용하여 시스템 보드, 손목 받침대 및 키보드 어셈블리에 힌지를 아래로 누릅니다. 4. 왼쪽 및 오른쪽 힌지를 시스템 보드, 손목 받침대 및 키보드 어셈블리에 고정하는 6개의 나사(M2.5x5)를 장착합니다. 5. 팬, 손목 받침대 및 키보드 어셈블리의 라우팅 가이드를 통해 디스플레이 케이블을 라우팅합니다. 6. 디스플레이 케이블을 시스템 보드의 커넥터에 밀어 넣은 후 래치를 눌러 케이블을 고정합니다.
작업후 필수 조건 1. 무선 카드를 장착합니다. 2. 베이스 덮개를 장착합니다.
30 디스플레이 조립품 분리 노트: 컴퓨터 내부에서 작업하기 전에 컴퓨터와 함께 제공된 안전 정보를 읽어 보고 컴퓨터 내부 작업을 시작하기 전에의 단계를 따르십시오. 컴퓨터 내부 작업을 마친 후에 컴퓨터 내부 작업을 마친 후에의 지침을 따르십시오. 추가 안전 모범 사례는 Regulatory Compliance(규정 준수) 홈페이지(www.dell.com/regulatory_compliance)를 참조하십시오. 필수 구성 요소 1. 베이스 덮개를 분리합니다. 2. 무선 카드를 분리합니다. 절차 1. 래치를 열고 시스템 보드에서 디스플레이 케이블을 분리합니다. 2. 디스플레이 케이블의 라우팅을 기록하고 팬, 손목 받침대 및 키보드 어셈블리의 라우팅 가이드에서 케이블을 제거합니다. 3. 왼쪽 및 오른쪽 힌지를 시스템 보드, 손목 받침대 및 키보드 어셈블리에 고정하는 6개의 나사(M2.5x5)를 제거합니다. 4. 힌지를 엽니다.
5. 손목 받침대 및 키보드 조립품을 일정 각도로 들어 올립니다. 6. 손목 받침대 및 키보드 어셈블리를 밀어 디스플레이 어셈블리에서 제거합니다. 7. 위의 모든 단계를 수행하고 나면 디스플레이 어셈블리가 남습니다.
디스플레이 조립품 분리 57
31 디스플레이 조립품 장착 노트: 컴퓨터 내부에서 작업하기 전에 컴퓨터와 함께 제공된 안전 정보를 읽어 보고 컴퓨터 내부 작업을 시작하기 전에의 단계를 따르십시오. 컴퓨터 내부 작업을 마친 후에 컴퓨터 내부 작업을 마친 후에의 지침을 따르십시오. 추가 안전 모범 사례는 Regulatory Compliance(규정 준수) 홈페이지(www.dell.com/regulatory_compliance)를 참조하십시오. 절차 노트: 디스플레이 어셈블리를 손목 받침대 및 키보드 어셈블리에 장착하기 전에 힌지가 최대한 열려 있는지 확인하십시오. 1. 손목 받침대 및 키보드 어셈블리를 일정 각도로 밉니다. 2. 손목 받침대 및 키보드 어셈블리를 닫습니다. 3. 정렬 포스트를 사용하여 시스템 보드, 손목 받침대 및 키보드 어셈블리에 힌지를 아래로 누릅니다. 4. 왼쪽 및 오른쪽 힌지를 시스템 보드, 손목 받침대 및 키보드 어셈블리에 고정하는 6개의 나사(M2.5x5)를 장착합니다.
5. 팬, 손목 받침대 및 키보드 어셈블리의 라우팅 가이드를 통해 디스플레이 케이블을 라우팅합니다. 6. 디스플레이 케이블을 시스템 보드의 커넥터에 밀어 넣은 후 래치를 눌러 케이블을 고정합니다. 작업후 필수 조건 1. 무선 카드를 장착합니다. 2. 베이스 덮개를 장착합니다.
32 I/O 보드 제거 노트: 컴퓨터 내부에서 작업하기 전에 컴퓨터와 함께 제공된 안전 정보를 읽어 보고 컴퓨터 내부 작업을 시작하기 전에의 단계를 따르십시오. 컴퓨터 내부 작업을 마친 후에 컴퓨터 내부 작업을 마친 후에의 지침을 따르십시오. 추가 안전 모범 사례는 Regulatory Compliance(규정 준수) 홈페이지(www.dell.com/regulatory_compliance)를 참조하십시오. 필수 구성 요소 주의: 코인 셀 배터리를 분리하면 BIOS 설정 프로그램 설정을 기본값으로 재설정합니다. 코인 셀 배터리와 함께 I/O 보드를 제 거하기 전에 BIOS 설정 프로그램의 설정을 기록하는 것이 좋습니다. 1. 베이스 덮개를 분리합니다. 2. 배터리를 분리합니다. 3. 하드 드라이브를 분리합니다. 절차 1. 코인 셀 배터리 케이블을 I/O 보드에서 연결 해제합니다. 2. 래치를 열고 I/O 보드 케이블을 시스템 보드에서 분리합니다. 3.
33 I/O 보드 장착 노트: 컴퓨터 내부에서 작업하기 전에 컴퓨터와 함께 제공된 안전 정보를 읽어 보고 컴퓨터 내부 작업을 시작하기 전에의 단계를 따르십시오. 컴퓨터 내부 작업을 마친 후에 컴퓨터 내부 작업을 마친 후에의 지침을 따르십시오. 추가 안전 모범 사례는 Regulatory Compliance(규정 준수) 홈페이지(www.dell.com/regulatory_compliance)를 참조하십시오. 절차 1. 정렬 포스트를 사용하여 I/O 보드를 손목 받침대 및 키보드 조립품에 놓습니다. 2. I/O 보드를 손목 받침대 및 키보드 어셈블리에 고정하는 나사(M2x4)를 장착합니다. 3. I/O 보드 케이블을 시스템 보드에 연결하고 래치를 닫아 케이블을 고정합니다. 4. I/O 보드에 코인 셀 배터리 케이블을 연결합니다. 작업후 필수 조건 1. 하드 드라이브를 장착합니다. 2. 배터리를 장착합니다. 3. 베이스 덮개를 장착합니다.
34 전원 버튼 보드 제거 노트: 컴퓨터 내부에서 작업하기 전에 컴퓨터와 함께 제공된 안전 정보를 읽어 보고 컴퓨터 내부 작업을 시작하기 전에의 단계를 따르십시오. 컴퓨터 내부 작업을 마친 후에 컴퓨터 내부 작업을 마친 후에의 지침을 따르십시오. 추가 안전 모범 사례는 Regulatory Compliance(규정 준수) 홈페이지(www.dell.com/regulatory_compliance)를 참조하십시오. 필수 구성 요소 1. 베이스 덮개를 분리합니다. 2. 팬을 분리합니다. 절차 1. 왼쪽 힌지를 손목 받침대 및 키보드 어셈블리에 고정하는 3개의 나사(M2.5x5)를 제거합니다. 2. 왼쪽 힌지를 엽니다. 3. 래치를 열고 시스템 보드에서 전원 버튼 보드 케이블을 분리합니다. 4. 전원 버튼 보드를 손목 받침대 및 키보드 조립품에 고정하는 테이프를 떼어냅니다. 5. 전원 버튼 보드를 손목 받침대 및 키보드 어셈블리에 고정하는 나사(M2x3)를 제거합니다. 6.
전원 버튼 보드 제거 63
35 전원 버튼 보드 장착 노트: 컴퓨터 내부에서 작업하기 전에 컴퓨터와 함께 제공된 안전 정보를 읽어 보고 컴퓨터 내부 작업을 시작하기 전에의 단계를 따르십시오. 컴퓨터 내부 작업을 마친 후에 컴퓨터 내부 작업을 마친 후에의 지침을 따르십시오. 추가 안전 모범 사례는 Regulatory Compliance(규정 준수) 홈페이지(www.dell.com/regulatory_compliance)를 참조하십시오. 절차 1. 전원 버튼 보드를 손목 받침대 및 키보드 조립품 아래에 밀어 넣고 전원 단추 보드의 나사 구멍을 손목 받침대 및 키보드 조립품의 나사 구멍에 맞춥니다. 2. 전원 버튼 보드를 손목 받침대 및 키보드 어셈블리에 고정하는 나사(M2x3)를 장착합니다. 3. 전원 버튼 보드를 손목 받침대 및 키보드 조립품에 고정하는 테이프를 부착합니다. 4. 전원 버튼 케이블을 시스템 보드에 밀어 넣고 래치를 닫아 케이블을 고정합니다. 5. 왼쪽 힌지를 닫습니다. 6.
작업후 필수 조건 1. 팬을 장착합니다. 2. 베이스 덮개를 장착합니다.
36 시스템 보드 제거 노트: 컴퓨터 내부에서 작업하기 전에 컴퓨터와 함께 제공된 안전 정보를 읽어 보고 컴퓨터 내부 작업을 시작하기 전에의 단계를 따르십시오. 컴퓨터 내부 작업을 마친 후에 컴퓨터 내부 작업을 마친 후에의 지침을 따르십시오. 추가 안전 모범 사례는 Regulatory Compliance(규정 준수) 홈페이지(www.dell.com/regulatory_compliance)를 참조하십시오. 노트: 해당 컴퓨터의 서비스 태그는 시스템 보드에 저장되어 있습니다. 시스템 보드를 장착한 후 BIOS 설정 프로그램에서 서비스 태그를 입력해야 합니다. 노트: 시스템 보드를 교체하면 BIOS 설정 프로그램을 사용하여 변경된 BIOS 변경사항이 모두 제거됩니다. 시스템 보드를 교체한 후에는 적절히 변경해야 합니다. 노트: 시스템 보드에서 케이블을 분리하기 전에 커넥터의 위치를 기록하여 시스템 보드를 교체한 후에 정확하게 다시 연결할 수 있도록 합니다. 필수 구성 요소 1. 베이스 덮개를 분리합니다.
11. 오른쪽 힌지를 시스템 보드에 고정하는 3개의 나사(M2.5x5)를 제거합니다. 12. 오른쪽 힌지를 엽니다. 13. 시스템 보드를 손목 받침대 및 키보드 어셈블리에 고정하는 나사(M2x4)를 제거합니다. 14. 손목 받침대 및 키보드 조립품에서 시스템 보드를 들어 올립니다.
시스템 보드 제거
37 시스템 보드 장착 노트: 컴퓨터 내부에서 작업하기 전에 컴퓨터와 함께 제공된 안전 정보를 읽어 보고 컴퓨터 내부 작업을 시작하기 전에의 단계를 따르십시오. 컴퓨터 내부 작업을 마친 후에 컴퓨터 내부 작업을 마친 후에의 지침을 따르십시오. 추가 안전 모범 사례는 Regulatory Compliance(규정 준수) 홈페이지(www.dell.com/regulatory_compliance)를 참조하십시오. 노트: 해당 컴퓨터의 서비스 태그는 시스템 보드에 저장되어 있습니다. 시스템 보드를 장착한 후 BIOS 설정 프로그램에서 서비스 태그를 입력해야 합니다. 노트: 시스템 보드를 교체하면 BIOS 설정 프로그램을 사용하여 변경된 BIOS 변경사항이 모두 제거됩니다. 시스템 보드를 교체한 후에는 적절히 변경해야 합니다. 절차 1. 시스템 보드의 나사 구멍을 손목 받침대 및 키보드 조립품의 나사 구멍에 맞춥니다. 2. 시스템 보드를 손목 받침대 및 키보드 어셈블리에 고정하는 나사(M2x4)를 장착합니다.
5. 지문 판독기 케이블을 시스템 보드의 커넥터에 밀어 넣고 래치를 닫습니다. 6. I/O 보드 케이블을 시스템 보드의 커넥터에 밀어 넣고 래치를 닫습니다. 7. 하드 드라이브 케이블을 시스템 보드의 커넥터에 밀어 넣고 래치를 닫습니다. 8. 터치패드 케이블을 시스템 보드의 커넥터에 밀어 넣고 래치를 닫습니다. 9. 키보드 백라이트 케이블을 시스템 보드의 커넥터에 밀어 넣고 래치를 닫습니다. 10. 키보드 케이블을 시스템 보드의 커넥터에 밀어 넣고 래치를 닫습니다. 11. 시스템 보드에 스피커 케이블을 연결합니다. 12. 전원 어댑터 포트 케이블을 시스템 보드에 연결합니다. 13. 전원 버튼 보드 케이블을 시스템 보드의 커넥터에 밀어 넣고 래치를 닫습니다. 14. 래치를 열고 디스플레이 케이블을 시스템 보드에 연결합니다.
작업후 필수 조건 1. 방열판을 장착합니다. 2. 팬을 장착합니다. 3. 솔리드 스테이트 드라이브/인텔 옵테인을 장착합니다. 4. 무선 카드를 장착합니다. 5. 메모리 모듈을 장착합니다. 6. 배터리를 장착합니다. 7. 베이스 덮개를 장착합니다. BIOS 설치 프로그램에 서비스 태그 입력 1. 컴퓨터를 켜거나 다시 시작합니다. 2. Dell 로고가 표시되면 F2 키를 눌러 BIOS 설치 프로그램에 접속합니다. 3. Main(기본) 탭으로 이동해 Service Tag Input(서비스 태그 입력) 필드에 서비스 태그를 입력합니다. 노트: 서비스 태그는 컴퓨터의 후면에 있는 영숫자 식별자입니다.
38 지문 인식기가 탑재된 전원 버튼 제거 노트: 컴퓨터 내부에서 작업하기 전에 컴퓨터와 함께 제공된 안전 정보를 읽어 보고 컴퓨터 내부 작업을 시작하기 전에의 단계를 따르십시오. 컴퓨터 내부 작업을 마친 후에 컴퓨터 내부 작업을 마친 후에의 지침을 따르십시오. 추가 안전 모범 사례는 Regulatory Compliance(규정 준수) 홈페이지(www.dell.com/regulatory_compliance)를 참조하십시오. 필수 구성 요소 1. 베이스 덮개를 분리합니다. 2. 배터리를 분리합니다. 3. 솔리드 스테이트 드라이브/인텔 옵테인을 제거합니다. 4. 팬을 분리합니다. 5. 방열판을 분리합니다. 6. 무선 카드를 분리합니다. 7. 전원 버튼 보드를 분리합니다. 8. 시스템 보드를 분리합니다. 절차 1. 지문 판독기 케이블을 떼어내 손목 받침대 및 키보드 어셈블리에서 분리합니다. 2. 지문 판독기가 장착된 전원 버튼을 손목 받침대 및 키보드 어셈블리에 고정하는 나사(M2x2)를 제거합니다. 3.
39 지문 판독기가 장착된 전원 버튼 장착 노트: 컴퓨터 내부에서 작업하기 전에 컴퓨터와 함께 제공된 안전 정보를 읽어 보고 컴퓨터 내부 작업을 시작하기 전에의 단계를 따르십시오. 컴퓨터 내부 작업을 마친 후에 컴퓨터 내부 작업을 마친 후에의 지침을 따르십시오. 추가 안전 모범 사례는 Regulatory Compliance(규정 준수) 홈페이지(www.dell.com/regulatory_compliance)를 참조하십시오. 절차 1. 정렬 포스트를 사용하여 지문 판독기가 장착된 전원 버튼을 손목 받침대 및 키보드 어셈블리에 맞추어 놓습니다. 2. 지문 판독기가 장착된 전원 버튼을 손목 받침대 및 키보드 어셈블리에 고정하는 나사(M2x2)를 장착합니다. 3. 지문 판독기 케이블을 손목 받침대 및 키보드 어셈블리에 부착합니다. 작업후 필수 조건 1. 시스템 보드를 장착합니다. 2. 전원 버튼 보드를 장착합니다. 3. 무선 카드를 장착합니다. 4. 방열판을 장착합니다. 5. 팬을 장착합니다. 6.
40 손목 받침대 및 키보드 어셈블리 제거 노트: 컴퓨터 내부에서 작업하기 전에 컴퓨터와 함께 제공된 안전 정보를 읽어 보고 컴퓨터 내부 작업을 시작하기 전에의 단계를 따르십시오. 컴퓨터 내부 작업을 마친 후에 컴퓨터 내부 작업을 마친 후에의 지침을 따르십시오. 추가 안전 모범 사례는 Regulatory Compliance(규정 준수) 홈페이지(www.dell.com/regulatory_compliance)를 참조하십시오. 필수 구성 요소 1. 베이스 덮개를 분리합니다. 2. 배터리를 분리합니다. 3. 팬을 분리합니다. 4. 방열판을 분리합니다. 5. 솔리드 스테이트 드라이브/인텔 옵테인을 제거합니다. 6. 무선 카드를 분리합니다. 7. 스피커를 분리합니다. 8. 하드 드라이브를 분리합니다. 9. 터치패드를 제거합니다. 10. 전원 어댑터 포트를 분리합니다. 11. 디스플레이 어셈블리를 분리합니다. 12. I/O 보드를 분리합니다. 13. 전원 버튼 보드를 분리합니다. 14. 시스템 보드를 분리합니다.
41 손목 받침대 및 키보드 어셈블리 교체 노트: 컴퓨터 내부에서 작업하기 전에 컴퓨터와 함께 제공된 안전 정보를 읽어 보고 컴퓨터 내부 작업을 시작하기 전에의 단계를 따르십시오. 컴퓨터 내부 작업을 마친 후에 컴퓨터 내부 작업을 마친 후에의 지침을 따르십시오. 추가 안전 모범 사례는 Regulatory Compliance(규정 준수) 홈페이지(www.dell.com/regulatory_compliance)를 참조하십시오. 절차 손목 받침대 및 키보드 어셈블리를 평평한 표면에 놓습니다. 작업후 필수 조건 1. 지문 판독기가 장착된 전원 버튼을 장착합니다(선택 사항). 2. 시스템 보드를 장착합니다. 3. 전원 버튼 보드를 장착합니다. 4. I/O 보드를 장착합니다. 5. 디스플레이 어셈블리를 장착합니다. 6. 전원 어댑터 포트를 장착합니다. 7. 터치패드를 장착합니다. 8. 하드 드라이브를 장착합니다. 9. 스피커를 장착합니다. 10. 무선 카드를 장착합니다.
11. 솔리드 스테이트 드라이브/인텔 옵테인을 장착합니다. 12. 방열판을 장착합니다. 13. 팬을 장착합니다. 14. 배터리를 장착합니다. 15. 베이스 덮개를 장착합니다.
42 디스플레이 베젤 분리 노트: 컴퓨터 내부에서 작업하기 전에 컴퓨터와 함께 제공된 안전 정보를 읽어 보고 컴퓨터 내부 작업을 시작하기 전에의 단계를 따르십시오. 컴퓨터 내부 작업을 마친 후에 컴퓨터 내부 작업을 마친 후에의 지침을 따르십시오. 추가 안전 모범 사례는 Regulatory Compliance(규정 준수) 홈페이지(www.dell.com/regulatory_compliance)를 참조하십시오. 필수 구성 요소 1. 베이스 덮개를 분리합니다. 2. 무선 카드를 분리합니다. 3. 디스플레이 어셈블리를 분리합니다. 절차 1. 플라스틱 스크라이브를 사용하여 디스플레이 후면 커버 및 안테나 어셈블리의 왼쪽 상단 바깥쪽 가장자리에서 디스플레이 베젤 을 조심스럽게 들어 올립니다. 2. 디스플레이 베젤을 디스플레이 후면 덮개 및 안테나 조립품에서 분리합니다.
43 디스플레이 베젤 장착 노트: 컴퓨터 내부에서 작업하기 전에 컴퓨터와 함께 제공된 안전 정보를 읽어 보고 컴퓨터 내부 작업을 시작하기 전에의 단계를 따르십시오. 컴퓨터 내부 작업을 마친 후에 컴퓨터 내부 작업을 마친 후에의 지침을 따르십시오. 추가 안전 모범 사례는 Regulatory Compliance(규정 준수) 홈페이지(www.dell.com/regulatory_compliance)를 참조하십시오. 절차 디스플레이 베젤을 디스플레이 후면 커버 및 안테나 어셈블리에 맞추고 조심스럽게 디스플레이 베젤을 제자리에 끼워 넣습니다. 작업후 필수 조건 1. 디스플레이 어셈블리를 장착합니다. 2. 무선 카드를 장착합니다. 3. 베이스 덮개를 장착합니다.
44 카메라 분리 노트: 컴퓨터 내부에서 작업하기 전에 컴퓨터와 함께 제공된 안전 정보를 읽어 보고 컴퓨터 내부 작업을 시작하기 전에의 단계를 따르십시오. 컴퓨터 내부 작업을 마친 후에 컴퓨터 내부 작업을 마친 후에의 지침을 따르십시오. 추가 안전 모범 사례는 Regulatory Compliance(규정 준수) 홈페이지(www.dell.com/regulatory_compliance)를 참조하십시오. 필수 구성 요소 1. 베이스 덮개를 분리합니다. 2. 무선 카드를 분리합니다. 3. 디스플레이 어셈블리를 분리합니다. 4. 디스플레이 베젤을 분리합니다. 절차 1. 플라스틱 스크라이브를 사용하여 카메라를 조심스럽게 들어 올려 디스플레이 후면 커버 및 안테나 어셈블리에서 분리합니다. 2. 카메라 모듈에서 카메라 케이블을 분리합니다. 3. 카메라 모듈을 디스플레이 후면 덮개와 안테나 조립품에서 들어 올립니다.
45 카메라 장착 노트: 컴퓨터 내부에서 작업하기 전에 컴퓨터와 함께 제공된 안전 정보를 읽어 보고 컴퓨터 내부 작업을 시작하기 전에의 단계를 따르십시오. 컴퓨터 내부 작업을 마친 후에 컴퓨터 내부 작업을 마친 후에의 지침을 따르십시오. 추가 안전 모범 사례는 Regulatory Compliance(규정 준수) 홈페이지(www.dell.com/regulatory_compliance)를 참조하십시오. 절차 1. 카메라 모듈을 카메라 케이블에 맞춥니다. 2. 카메라 케이블을 카메라 모듈에 연결합니다. 3. 정렬 포스트를 사용하여 카메라 모듈을 디스플레이 후면 커버 및 안테나 어셈블리에 부착합니다. 작업후 필수 조건 1. 디스플레이 베젤을 장착합니다. 2. 디스플레이 어셈블리를 장착합니다. 3. 무선 카드를 장착합니다. 4. 베이스 덮개를 장착합니다.
46 디스플레이 패널 분리 노트: 컴퓨터 내부에서 작업하기 전에 컴퓨터와 함께 제공된 안전 정보를 읽어 보고 컴퓨터 내부 작업을 시작하기 전에의 단계를 따르십시오. 컴퓨터 내부 작업을 마친 후에 컴퓨터 내부 작업을 마친 후에의 지침을 따르십시오. 추가 안전 모범 사례는 Regulatory Compliance(규정 준수) 홈페이지(www.dell.com/regulatory_compliance)를 참조하십시오. 필수 구성 요소 1. 베이스 덮개를 분리합니다. 2. 무선 카드를 분리합니다. 3. 디스플레이 어셈블리를 분리합니다. 4. 디스플레이 베젤을 분리합니다. 절차 1. 디스플레이 패널을 디스플레이 후면 커버와 안테나 어셈블리에 고정하는 4개의 나사(M2x2)를 제거합니다. 2. 디스플레이 패널을 들어 올려 뒤집습니다. 3. 디스플레이 패널 후면의 디스플레이 케이블을 부착하는 테이프를 떼어냅니다. 4. 래치를 들어 올리고 디스플레이 패널 케이블 커넥터에서 디스플레이 케이블을 분리합니다. 5.
디스플레이 패널 분리
47 디스플레이 패널 장착 노트: 컴퓨터 내부에서 작업하기 전에 컴퓨터와 함께 제공된 안전 정보를 읽어 보고 컴퓨터 내부 작업을 시작하기 전에의 단계를 따르십시오. 컴퓨터 내부 작업을 마친 후에 컴퓨터 내부 작업을 마친 후에의 지침을 따르십시오. 추가 안전 모범 사례는 Regulatory Compliance(규정 준수) 홈페이지(www.dell.com/regulatory_compliance)를 참조하십시오. 절차 1. 디스플레이 패널을 평평하고 깨끗한 표면에 놓습니다. 2. 디스플레이 케이블을 디스플레이 패널 후면의 커넥터에 연결하고 래치를 닫아 케이블을 고정합니다. 3. 디스플레이 케이블을 디스플레이 패널 후면에 고정시키는 테이프를 떼어냅니다. 4. 디스플레이 패널을 디스플레이 후면 커버 및 안테나 어셈블리에 놓습니다. 5.
작업후 필수 조건 1. 디스플레이 베젤을 장착합니다. 2. 디스플레이 어셈블리를 장착합니다. 3. 무선 카드를 장착합니다. 4. 베이스 덮개를 장착합니다.
48 디스플레이 힌지 분리 노트: 컴퓨터 내부에서 작업하기 전에 컴퓨터와 함께 제공된 안전 정보를 읽어 보고 컴퓨터 내부 작업을 시작하기 전에의 단계를 따르십시오. 컴퓨터 내부 작업을 마친 후에 컴퓨터 내부 작업을 마친 후에의 지침을 따르십시오. 추가 안전 모범 사례는 Regulatory Compliance(규정 준수) 홈페이지(www.dell.com/regulatory_compliance)를 참조하십시오. 필수 구성 요소 1. 베이스 덮개를 분리합니다. 2. 무선 카드를 분리합니다. 3. 디스플레이 어셈블리를 분리합니다. 4. 디스플레이 베젤을 분리합니다. 5. 디스플레이 패널을 분리합니다. 절차 1. 힌지를 디스플레이 후면 커버 및 안테나 어셈블리에 고정하는 8개의 나사(M2.5x2.5)를 제거합니다. 2. 힌지 브래킷을 디스플레이 후면 커버 및 안테나 어셈블리에 고정하는 2개의 나사(M2x2)를 제거합니다. 3.
49 디스플레이 힌지 장착 노트: 컴퓨터 내부에서 작업하기 전에 컴퓨터와 함께 제공된 안전 정보를 읽어 보고 컴퓨터 내부 작업을 시작하기 전에의 단계를 따르십시오. 컴퓨터 내부 작업을 마친 후에 컴퓨터 내부 작업을 마친 후에의 지침을 따르십시오. 추가 안전 모범 사례는 Regulatory Compliance(규정 준수) 홈페이지(www.dell.com/regulatory_compliance)를 참조하십시오. 절차 1. 힌지 및 브래킷의 나사 구멍을 디스플레이 후면 커버 및 안테나 어셈블리의 나사 구멍에 맞춥니다. 2. 힌지 플레이트를 디스플레이 후면 커버 및 안테나 어셈블리에 고정하는 2개의 나사(M2x2)를 장착합니다. 3. 힌지를 디스플레이 후면 커버 및 안테나 어셈블리에 고정하는 8개의 나사(M2.5x2.5)를 장착합니다. 작업후 필수 조건 1. 디스플레이 패널을 장착합니다. 2. 디스플레이 베젤을 장착합니다. 3. 디스플레이 어셈블리를 장착합니다. 4. 무선 카드를 장착합니다. 5.
50 디스플레이 케이블 분리 노트: 컴퓨터 내부에서 작업하기 전에 컴퓨터와 함께 제공된 안전 정보를 읽어 보고 컴퓨터 내부 작업을 시작하기 전에의 단계를 따르십시오. 컴퓨터 내부 작업을 마친 후에 컴퓨터 내부 작업을 마친 후에의 지침을 따르십시오. 추가 안전 모범 사례는 Regulatory Compliance(규정 준수) 홈페이지(www.dell.com/regulatory_compliance)를 참조하십시오. 필수 구성 요소 1. 베이스 덮개를 분리합니다. 2. 무선 카드를 분리합니다. 3. 디스플레이 어셈블리를 분리합니다. 4. 디스플레이 베젤을 분리합니다. 5. 디스플레이 패널을 분리합니다. 6. 디스플레이 힌지를 분리합니다. 절차 1. 카메라 모듈에서 카메라 케이블을 분리합니다. 2. 디스플레이 케이블 라우팅을 기록하고 디스플레이 후면 커버와 안테나 어셈블리의 라우팅 가이드에서 케이블을 제거합니다. 3. 디스플레이 후면 커버 및 안테나 어셈블리에서 디스플레이 케이블을 제거합니다.
51 디스플레이 케이블 교체 노트: 컴퓨터 내부에서 작업하기 전에 컴퓨터와 함께 제공된 안전 정보를 읽어 보고 컴퓨터 내부 작업을 시작하기 전에의 단계를 따르십시오. 컴퓨터 내부 작업을 마친 후에 컴퓨터 내부 작업을 마친 후에의 지침을 따르십시오. 추가 안전 모범 사례는 Regulatory Compliance(규정 준수) 홈페이지(www.dell.com/regulatory_compliance)를 참조하십시오. 절차 1. 디스플레이 케이블을 라우팅 가이드에 따라 디스플레이 아래쪽(힌지 주변)부터 라우팅합니다. 2. 디스플레이 후면 커버 및 안테나 어셈블리의 왼쪽에 있는 라우팅 가이드를 통해 나머지 디스플레이 케이블을 라우팅합니다. 3. 케이블을 고정시키는 카메라 케이블을 카메라의 커넥터에 밀어 넣습니다. 작업후 필수 조건 1. 디스플레이 힌지를 장착합니다. 2. 디스플레이 패널을 장착합니다. 3. 디스플레이 베젤을 장착합니다. 4. 디스플레이 어셈블리를 장착합니다. 5. 무선 카드를 장착합니다. 6.
52 디스플레이 후면 덮개 및 안테나 조립품 분리 노트: 컴퓨터 내부에서 작업하기 전에 컴퓨터와 함께 제공된 안전 정보를 읽어 보고 컴퓨터 내부 작업을 시작하기 전에의 단계를 따르십시오. 컴퓨터 내부 작업을 마친 후에 컴퓨터 내부 작업을 마친 후에의 지침을 따르십시오. 추가 안전 모범 사례는 Regulatory Compliance(규정 준수) 홈페이지(www.dell.com/regulatory_compliance)를 참조하십시오. 필수 구성 요소 1. 베이스 덮개를 분리합니다. 2. 무선 카드를 분리합니다. 3. 디스플레이 어셈블리를 분리합니다. 4. 디스플레이 베젤을 분리합니다. 5. 카메라를 분리합니다. 6. 디스플레이 패널을 분리합니다. 7. 디스플레이 힌지를 분리합니다. 8. 디스플레이 케이블을 분리합니다. 절차 위의 단계를 모두 수행하고 나면 디스플레이 후면 커버와 안테나 어셈블리가 남습니다.
53 디스플레이 후면 덮개 및 안테나 조립품 교체 노트: 컴퓨터 내부에서 작업하기 전에 컴퓨터와 함께 제공된 안전 정보를 읽어 보고 컴퓨터 내부 작업을 시작하기 전에의 단계를 따르십시오. 컴퓨터 내부 작업을 마친 후에 컴퓨터 내부 작업을 마친 후에의 지침을 따르십시오. 추가 안전 모범 사례는 Regulatory Compliance(규정 준수) 홈페이지(www.dell.com/regulatory_compliance)를 참조하십시오. 절차 디스플레이 후면 덮개와 안테나 조립품을 깨끗하고 평평한 표면에 둡니다. 작업후 필수 조건 1. 디스플레이 케이블을 장착합니다. 2. 디스플레이 힌지를 장착합니다. 3. 디스플레이 패널을 장착합니다. 4. 카메라를 장착합니다. 5. 디스플레이 베젤을 장착합니다. 6. 디스플레이 어셈블리를 장착합니다. 7. 무선 카드를 장착합니다. 8. 베이스 덮개를 장착합니다.
54 장치 드라이버 Intel 칩셋 소프트웨어 설치 유틸리티 장치 관리자에서 칩셋 드라이버가 설치되어 있는지 확인합니다. www.dell.com/support에서 칩셋 업데이트를 설치합니다. 비디오 드라이버 장치 관리자에서 비디오 드라이버가 설치되어 있는지 확인합니다. www.dell.com/support에서 비디오 드라이버 업데이트를 설치합니다. 인텔 직렬 IO 드라이버 장치 관리자에서 인텔 직렬 IO 드라이버가 설치되어 있는지 확인합니다. www.dell.com/support에서 드라이버 업데이트를 설치합니다. Intel Trusted Execution 엔진 인터페이스 장치 관리자에서 Intel Trusted Execution 엔진 인터페이스 드라이버가 설치되었는지 확인합니다. www.dell.com/support에서 드라이버 업데이트를 설치합니다. 인텔 가상 버튼 드라이버 장치 관리자에서 Intel Virtual Button 드라이버가 설치되어 있는지 확인합니다. www.dell.
55 시스템 설정 노트: 컴퓨터 및 장착된 장치에 따라 이 섹션에 나열된 항목이 표시될 수도 있고, 표시되지 않을 수도 있습니다. 시스템 설정 주의: 컴퓨터 전문가가 아닌 경우 BIOS 설정 프로그램의 설정을 변경하지 마십시오. 일부 변경 시 컴퓨터가 올바르게 작동하지 않을 수 있습니다. 노트: BIOS 설정 프로그램을 변경하기 전에 나중에 참조할 수 있도록 BIOS 설정 프로그램 화면 정보를 기록해 두는 것이 좋습니 다. BIOS 설정 프로그램은 다음과 같은 용도로 사용합니다. ● 컴퓨터에 설치된 하드웨어의 정보 찾기(예: RAM 용량, 하드 드라이브 크기 등) ● 시스템 구성 정보를 변경합니다. ● 사용자 암호, 설치된 하드 드라이브 유형, 기본 디바이스 활성화 또는 비활성화와 같은 사용자 선택 옵션 설정 또는 변경 BIOS 설정 프로그램 시작하기 1. 컴퓨터를 켜거나 다시 시작합니다. 2. POST 중에 DELL 로고가 표시되면 F2 프롬프트가 표시되는 즉시 F2 키를 누릅니다.
● F12 키를 눌러 1회 부팅 메뉴 실행 부팅할 수 있는 장치가 진단 옵션과 함께 원타임 부팅 메뉴에 표시됩니다. 부팅 메뉴 옵션은 다음과 같습니다. ● 이동식 드라이브(사용 가능한 경우) ● STXXXX 드라이브(사용 가능한 경우) 노트: XXX는 SATA 드라이브 번호를 표시합니다. ● 옵티컬 드라이브(사용 가능한 경우) ● SATA 하드 드라이브(사용 가능한 경우) ● 진단 프로그램 부트 순서 화면에는 시스템 설정 화면에 액세스하기 위한 옵션도 표시됩니다. 시스템 설치 옵션 노트: 컴퓨터와 설치된 디바이스에 따라 이 섹션에 나열된 항목이 표시될 수도 있고, 표시되지 않을 수도 있습니다. 표 3. 시스템 설치 옵션- 시스템 정보 메뉴 일반 시스템 정보 시스템 정보 BIOS 버전 BIOS 버전 번호를 표시합니다. 서비스 태그 컴퓨터의 서비스 태그를 표시합니다. 자산 태그 컴퓨터의 자산 태그를 표시합니다. 오너십 태그 컴퓨터의 소유자 자산 태그를 표시합니다.
표 3. 시스템 설치 옵션- 시스템 정보 메뉴 (계속) 일반 시스템 정보 Primary HDD 컴퓨터의 기본 하드 드라이브 정보를 제공합니다. M.2 SATA SSD 컴퓨터의 M.2 SATA SSD 디바이스 정보를 표시합니다. M.2 PCIe SSD-0 컴퓨터의 M.2 PCIe SSD 정보를 표시합니다. LOM MAC 주소 컴퓨터의 LOM MAC 주소를 표시합니다. 비디오 컨트롤러 컴퓨터의 비디오 컨트롤러 유형을 표시합니다. dGPU 비디오 컨트롤러 컴퓨터의 독립 그래픽 정보가 표시됩니다. Video BIOS Version 컴퓨터의 비디오 BIOS 버전을 표시합니다. 비디오 메모리 컴퓨터의 비디오 메모리 정보를 표시합니다. Panel Type 컴퓨터의 패널 유형을 표시합니다. Native Resolution 컴퓨터의 기본 해상도를 표시합니다. Audio Controller 컴퓨터의 오디오 컨트롤러 정보를 표시합니다.
표 4. 시스템 설치 옵션—시스템 구성 메뉴 (계속) 시스템 구성 배터리에서의 키보드 백라이트 시간 초과 이 기능은 컴퓨터가 배터리 전원으로 실행될 때 키보드 백라이트의 시간 제한 값 을 정의합니다. 기타 디바이스 다양한 온보드 디바이스를 활성화 또는 비활성화할 수 있습니다. 표 5. 시스템 설치 옵션—비디오 메뉴 비디오 LCD 밝기 배터리 및 AC 전원과 별개로 패널 밝기를 설정합니다. 표 6. 시스템 설치 옵션—보안 메뉴 보안 관리자 암호 관리자 암호를 설정, 변경 또는 삭제합니다. 시스템 암호 시스템 암호를 설정, 변경 또는 삭제합니다. 내부 HDD-0 암호 내장 하드 디스크 드라이브 암호를 설정, 변경 또는 삭제합니다. 강력한 암호 강력한 암호 사용을 활성화 또는 비활성화합니다. 암호 구성 관리자 암호 및 시스템 암호에 허용되는 최소 및 최대 문자 수를 제어합니다. 암호 우회 시스템을 재시작하는 동안 시스템(부팅) 암호와 내장형 HDD 암호를 생략할 수 있 습니다.
표 8. 시스템 설치 옵션—Intel 소프트웨어 가드 확장 메뉴 (계속) 인텔 소프트웨어 가드 확장 성능 멀티 코어 지원 여러 코어를 활성화합니다. 기본값: 활성화. Intel SpeedStep Intel SpeedStep 기술을 활성화 또는 비활성화합니다. 기본값: 활성화. 노트: 활성화하는 경우, 프로세서 클록 속도와 코어 전압이 프로세서 부하에 따 라 동적으로 조정됩니다. C-States Control 추가 프로세서 절전 상태를 활성화 또는 비활성화합니다. 기본값: 활성화. Intel TurboBoost 프로세서의 Intel TurboBoost 모드를 활성화 또는 비활성화합니다. 기본값: 활성화. HyperThread control 프로세서의 하이퍼스레딩을 활성화 또는 비활성화합니다. 기본값: 활성화. 전원 관리 AC Behavior AC 전원 공급 시 자동으로 시스템의 전원을 켤 수 있습니다.
표 9. 시스템 설치 옵션—가상화 지원 메뉴 가상화 지원 가상화 VMM(Virtual Machine Monitor)이 Intel 가상화 기술이 제공하는 추가 하드웨어 기능 을 활용할지 여부를 지정합니다. VT for Direct I/O VMM(Virtual Machine Monitor)이 Direct I/O용 Intel 가상화 기술이 제공하는 추가 하드웨어 기능을 활용할지 여부를 지정합니다. 표 10. 시스템 설치 옵션—무선 메뉴 무선 Wireless Switch 무선 디바이스를 무선 스위치로 제어할 수 있을지 여부를 결정합니다. 무선 디바이스 활성화 내부 무선 디바이스를 활성화 또는 비활성화합니다. 표 11. 시스템 설치 옵션—유지 보수 메뉴 유지 보수 서비스 태그 시스템의 서비스 태그를 표시합니다. 자산 태그 시스템 자산 태그를 생성합니다. BIOS Downgrade 시스템 펌웨어의 이전 버전으로의 플래시를 제어합니다.
노트: 시스템 및 설정 암호 기능은 비활성화되어 있습니다. 시스템 설정 암호 할당 설정 안 됨 상태일 때만 새 시스템 또는 관리자 암호를 할당할 수 있습니다. 시스템 설정에 들어가려면 전원이 켜진 직후 또는 재부팅 직후에 키를 누릅니다. 1. 시스템 BIOS 또는 시스템 설정 화면에서 보안을 선택하고 키를 누릅니다. Security (보안) 화면이 표시됩니다. 2. 시스템/관리자 암호를 선택하고 새 암호 입력 필드에서 암호를 생성합니다. 다음 지침을 따라 시스템 암호를 할당합니다. ● 암호 길이는 최대 32글자입니다. ● 암호에는 0부터 9까지의 숫자가 포함될 수 있습니다. ● 소문자만 유효하며 대문자는 사용할 수 없습니다. ● 다음 특수 문자만 사용할 수 있습니다: 공백, (”), (+), (,), (-), (.), (/), (;), ([), (\), (]), (`). 3. 새 암호 확인 필드에 입력했던 시스템 암호를 입력하고 OK(확인)를 클릭합니다. 4.
노트: Windows 또는 애플리케이션 암호를 재설정하는 방법에 대한 자세한 내용은 Windows 또는 애플리케이션과 함께 제공되는 문서 자료를 참조하십시오. BIOS 업데이트 Windows에서 BIOS 업데이트 1. www.dell.com/support로 이동합니다. 2. 제품 지원을 클릭합니다. 지원 검색 상자에서 컴퓨터의 서비스 태그를 입력한 다음 검색을 클릭합니다. 노트: 서비스 태그가 없는 경우 SupportAssist 기능을 사용하여 자동으로 컴퓨터를 식별합니다. 제품 ID를 사용하거나 컴퓨터 모델을 수동으로 찾아볼 수도 있습니다. 3. Drivers & Downloads(드라이버 및 다운로드)를 클릭합니다. 드라이버 찾기를 확장합니다. 4. 컴퓨터에 설치된 운영 체제를 선택합니다. 5. 범주 드롭다운 목록에서 BIOS를 선택합니다. 6. 최신 BIOS 버전을 선택하고 다운로드를 클릭하여 컴퓨터에 대한 BIOS 파일을 다운로드합니다. 7.
F12 원타임 부팅 메뉴에서 BIOS를 업데이트하려면 다음이 필요합니다. ● ● ● ● FAT32 파일 시스템으로 포맷된 USB 드라이브(키 자체가 부팅용일 필요는 없음) Dell 지원 웹사이트에서 다운로드하여 USB 드라이브의 루트에 복사한 BIOS 실행 파일 컴퓨터에 연결된 AC 전원 어댑터 정상 작동하는 BIOS 플래시용 컴퓨터 배터리 F12 메뉴에서 BIOS 업데이트 플래시 프로세스를 실행하려면 다음 단계를 수행합니다. 주의: BIOS 업데이트가 진행 중일 때 컴퓨터의 전원을 끄지 마십시오. 컴퓨터를 끄면 컴퓨터가 부팅되지 않을 수 있습니다. 1. 꺼진 상태에서 플래시를 복사한 USB 드라이브를 컴퓨터의 USB 포트에 삽입합니다. 2. 컴퓨터의 전원을 켜고 F12 키를 눌러 원타임 부팅 메뉴에 액세스합니다. 마우스 또는 화살표 키를 사용하여 BIOS 업데이트를 선택 한 다음 Enter 키를 누릅니다. 플래시 BIOS 메뉴가 표시됩니다. 3. 파일에서 플래시를 클릭합니다. 4.
56 문제 해결 부풀어 오른 리튬 이온 배터리 취급 대부분의 노트북 컴퓨터와 같이 Dell 노트북은 리튬 이온 배터리를 사용합니다. 리튬 폴리머 배터리는 리튬 이온 폴리머 배터리의 한 유형입니다. 리튬 이온 폴리머 배터리는 슬림형 폼 팩터(특히 최신 울트라 씬 노트북 컴퓨터에 사용)와 긴 배터리 지속 시간 때문에 최근 들어 인기가 높아졌고 전자 업계에서 표준이 되었습니다. 리튬 이온 폴리머 배터리 기술에는 배터리 셀이 부풀어 오를 가능성이 있습니다. 부풀어 오른 배터리는 노트북 컴퓨터의 성능에 영향을 줄 수 있습니다. 배터리가 부풀어 오르면, 오작동이 발생할 수 있는 디바이스 인클로저 또는 내부 구성 요소의 추가 손상 가능성을 방지하기 위해 노트북 컴퓨터의 사용을 중단하고, AC 어댑터를 연결 해제하고 배터리를 방전합니다. 부풀어 오른 배터리는 사용하지 않아야 하고 적절하게 교체 및 폐기해야 합니다.
노트: 일부 테스트는 특정 디바이스를 위한 것이며 사용자 상호 작용이 필요합니다. 진단 테스트를 수행할 때는 컴퓨터 앞에 있어 야 합니다. 자세한 정보는 SupportAssist 부팅 전 시스템 성능 확인을 참조하십시오. 시스템 - 진단 표시등 전원 및 배터리 상태 표시등 전원 및 배터리 상태 표시등은 컴퓨터의 전원 및 배터리 상태를 나타냅니다. 전원 상태는 다음과 같습니다. 솔리드 화이트: 전원 어댑터가 연결되어 있고 배터리 잔량이 5%를 넘습니다. 주황색: 컴퓨터가 배터리로 작동하는 중이고 배터리 잔량이 5% 미만입니다. 꺼짐: ● 전원 어댑터가 연결되어 있고 배터리가 완전히 충전되었습니다. ● 컴퓨터가 배터리로 작동하는 중이고 배터리 잔량이 5%를 넘습니다. ● 컴퓨터가 대기 모드, 최대 절전 모드 또는 꺼져 있습니다. 전원 및 배터리 상태 표시등은 다양한 장애를 나타내는 사전 정의된 "비프음 코드"에 따라 주황색 또는 흰색으로 깜박일 수도 있습니 다.
Dell SupportAssist OS Recovery는 Windows 운영 체제와 함께 설치되는 모든 Dell 컴퓨터에 사전 설치되어 있는 독립 실행형 툴입니다. 컴퓨터가 운영 체제로 부팅하기 전에 발생할 수 있는 문제를 진단하고 해결할 수 있는 툴로 구성됩니다. 이 툴을 통해 하드웨어 문제 를 진단하거나, 컴퓨터를 수리하거나, 파일을 백업하거나, 출하 시 상태로 컴퓨터를 복원할 수 있습니다. 소프트웨어 또는 하드웨어 장애로 인해 컴퓨터가 기본 운영 체제로 부팅할 수 없을 때 컴퓨터 문제를 해결하고 수정하기 위해 Dell Support 웹사이트에서 이 툴을 다운로드할 수도 있습니다. Dell SupportAssist OS Recovery에 대한 자세한 내용은 Dell SupportAssist OS Recovery 사용자 가이드(www.dell.com/ serviceabilitytools)를 참조하십시오. SupportAssist를 클릭한 후 SupportAssist OS Recovery를 클릭합니다.
잔류 전원 방전(하드 리셋 수행) 잔류 전원은 전원을 끄고 배터리가 제거된 후에도 컴퓨터에 남아 있는 정전기입니다. 안전을 위해 그리고 컴퓨터에서 중요한 전자 구성 요소를 보호하기 위해 컴퓨터의 구성 요소를 제거하거나 교체하기 전에 잔류 전원 을 방전해야 합니다. 컴퓨터 전원을 켜지 않거나 운영 체제로 부팅하지 않는 경우에도 "하드 리셋" 수행이라고도 하는 잔류 전원 방전은 일반적인 문제 해 결 단계이기도 합니다. 잔류 전원을 방전하려면(하드 리셋 수행) 1. 컴퓨터를 끕니다. 2. 전원 어댑터를 컴퓨터에서 연결 해제합니다. 3. 베이스 커버를 제거합니다. 4. 배터리를 제거합니다. 5. 20초간 전원 버튼을 길게 눌러 잔류 전원을 방전시킵니다. 6. 배터리를 설치합니다. 7. 베이스 커버를 설치합니다. 8. 전원 어댑터를 컴퓨터에 연결합니다 9. 컴퓨터를 켭니다. 노트: 하드 리셋 수행에 대한 자세한 내용은www.dell.com/support에서 기술 자료 문서 000130881을 참조하십시오.
57 도움말 보기 및 Dell에 문의하기 자체 도움말 리소스 다음과 같은 자체 도움말 리소스를 이용해 Dell 제품 및 서비스에 관한 정보 및 도움말을 얻을 수 있습니다. 표 16. 자체 도움말 리소스 자체 도움말 리소스 리소스 위치 Dell 제품 및 서비스 정보 www.dell.com My Dell 애플리케이션 추가 정보 지원 문의 Windows 검색에서 Contact Support를 입력한 다음 Enter 키 를 누릅니다. 운영 체제에 대한 온라인 도움말 www.dell.com/support/windows 비디오, 매뉴얼 및 문서를 통해 상위 솔루션, 진단, 드라이버 및 다운로드에 액세스하고 컴퓨터에 대해 자세히 알아봅니다. Dell 컴퓨터는 서비스 태그 또는 익스프레스 서비스 코드로 고유 하게 식별됩니다. Dell 컴퓨터에 대한 관련 지원 리소스를 보려면 www.dell.com/support에서 서비스 태그 또는 익스프레스 서비스 코드를 입력합니다.