Inspiron 3593 Servicemanual Forordningsmodel: P75F Forordningstype: P75F013
Bemærk, forsigtig og advarsel BEMÆRK En NOTE angiver vigtige oplysninger, som hjælper dig med at bruge computeren bedre. FORSIGTIG FORSIGTIG angiver enten en mulig beskadigelse af hardware eller tab af data, og oplyser dig om, hvordan du kan undgå dette problem. ADVARSEL ADVARSEL angiver risiko for tingskade, legemsbeskadigelse eller død. © 2019 Dell Inc. eller dets datterselskaber. Alle rettigheder forbeholdes. Dell, EMC, og andre varemærker er varemærker tilhørende Dell Inc.
Indholdsfortegnelse 1 Arbejde med indersiden af din computer......................................................................................... 6 Sikkerhedsinstruktioner.........................................................................................................................................................6 Før du udfører arbejde på computerens indvendige dele.................................................................................................6 Før du starter................
Genmontering af berøringspladen............................................................................................................................... 39 Højttalere.............................................................................................................................................................................. 40 Sådan fjernes højttalerne.........................................................................................................................................
Sådan hentes chipsætdriveren.......................................................................................................................................... 74 Sådan hentes driveren til mediekortlæseren....................................................................................................................74 Sådan hentes WiFi-driveren...............................................................................................................................................
1 Arbejde med indersiden af din computer Sikkerhedsinstruktioner Følg sikkerhedsinstruktionerne med henblik på din egen sikkerhed og for at beskytte computeren og arbejdsmiljøet mod mulige skader. Med mindre andet er beskrevet, det antages, at du har læst sikkerhedsvejledningen, der blev leveret med din computer. BEMÆRK Før du arbejder med computerens indvendige dele, skal du læse de sikkerhedsinstruktioner, der fulgte med computeren.
5. Fjern alle mediekort og optiske diske fra computeren, hvis relevant. Beskyttelse mod elektrostatisk afladning (ESD) ESD er til stor bekymring, når du håndterer elektroniske komponenter, især følsomme komponenter som ekspansionskort, processorer, hukommelses-DIMM'er og systemkort. Meget små afladninger kan beskadige kredsløb på måder, som måske ikke er indlysende, såsom intermitterende problemer eller kortere levetid.
• • i et datacenter; skriveborde eller bærbare er typisk placeret på kontorskriveborde eller i båse. Kig altid efter et stort, åbent arbejdsområde, der ikke roder, og som er stort nok til at implementere ESD-sættet, med yderligere plads til at rumme den type system, som bliver repareret. Arbejdspladsen bør også være uden isolatorer, der kan forårsage en ESD-hændelse.
2 Sådan fjernes og installeres komponenter Anbefalet værktøj Procedurerne i dette dokument kræver eventuelt følgende værktøj: • • • Phillips-skruetrækker nr. 1 Skruetrækker med lige kærv Plastiksyl Liste over skruer BEMÆRK Når skruer fjernes fra en komponent, anbefales det at bemærke skruetypen, antallet af skruer, og dernæst igen placere dem i en skrueopbevaringsboks. Dette er for at sikre, at det korrekte antal skruer og den korrekte skruetype gendannes, når komponenten er udskiftet..
Komponent Fastgjort til Skruetype Antal Hængselsbeslag Skærmens bagdæksel og antennemodul M2,5x4 8 Hængselsbeslag Skærmens bagdæksel og antennemodul M2x2 2 I/O-kort Håndfladestøtte og tastaturmodul M2x4 1 Optisk drevbøjle (for computere, hvor optisk drev medfølger) Optisk drev M2x2 2 Stikkort til optisk drev (for computere, hvor optisk drev medfølger) Håndfladestøtte og tastaturmodul M2x2 stort hoved 1 Strømadapterport Håndfladestøtte og tastaturmodul M2x3 1 Strømknapkort Håndfl
4. Fjern de to skruer (M2x3), som fastgør bøjlen for det optiske drev til det optiske drev. 5. Fjern bøjlen for det optiske drev fra det optiske drev. 6. Træk forsigtigt i rammen for det optiske drev for at fjerne den fra det optiske drev. Genmontering af det optiske drev BEMÆRK Før du arbejder med computerens indvendige dele, skal du læse de sikkerhedsinstruktioner, der fulgte med computeren, og følge trinene i Før du arbejder med computerens indvendige dele.
Procedure 1. BEMÆRK Gælder kun for computere, der sendes med optisk drev. Ret tapperne på rammen for det optiske drev ind efter slottene på det optiske drev, og snap rammen for det optiske drev på plads. 2. Juster skruehullerne i beslaget til det optiske drev ind med skruehullerne i det optiske drev. 3. Genmonter de to skruer (M2x3), som fastgør bøjlen for det optiske drev til det optiske drev. 4. Skub modulet for det optiske drev i ind båsen for det optiske drev. 5.
Bunddæksel Fjernelse af bunddækslet BEMÆRK Før du arbejder med computerens indvendige dele, skal du læse de sikkerhedsinstruktioner, der fulgte med computeren, og følge trinene i Før du arbejder med computerens indvendige dele. Efter du har arbejdet på computerens indvendige dele, følg vejledningen i Efter du har udført arbejde på computerens indvendige dele. For flere oplysninger om bedste praksis for sikkerhed, se hjemmesiden Regulatory Compliance på www.dell.com/regulatory_compliance.
BEMÆRK De følgende trin gælder kun, hvis du ønsker at fjerne flere komponenter fra din computer. 6. Pil tapen, der fastgør batterikablet til stikket, af, og kobl batterikablet fra systemkortet. 7. Tryk og hold tænd/sluk-knappen nede i 5 sekunder for at jorde computeren og dræne den resterende strøm. Procedure for computere, der sendes med optisk drev 1. Løsn de tre monteringsskruer på bunddækslet. 2. Fjern skruen (M2x4), der fastgør bunddækslet til håndfladestøtten og tastaturmodulet. 3.
5. Lirk bunddækslet løs med en plastikpen, startende i det øverste venstre hjørne. 6. Løft bunddækslet af håndfladestøtten og tastaturmodulet. BEMÆRK De følgende trin gælder kun, hvis du ønsker at fjerne flere komponenter fra din computer. 7. Pil tapen, der fastgør batterikablet til stikket, af, og kobl batterikablet fra systemkortet. 8. Frakobl batteriet fra systemkortet.
9. Tryk og hold tænd/sluk-knappen nede i 5 sekunder for at jorde computeren og dræne den resterende strøm. Sådan genmonteres bunddækslet BEMÆRK Før du arbejder med computerens indvendige dele, skal du læse de sikkerhedsinstruktioner, der fulgte med computeren, og følge trinene i Før du arbejder med computerens indvendige dele. Efter du har arbejdet på computerens indvendige dele, følg vejledningen i Efter du har udført arbejde på computerens indvendige dele.
4. Stram de tre skruer, der fastgør bunddækslet til håndfladestøtten og tastaturmodulet. 5. Genmonter de seks skruer (M2,5x7), der fastgør bunddækslet til håndfladestøtten og tastaturmodulet. 6. Fjern skruen (M2x4), der fastgør bunddækslet til håndfladestøtten og tastaturmodulet. Procedure for computere, der sendes med optisk drev 1. Slut batterikablet til systemkortet, og påfør tapen, der fastgør batterikablet til stikket på systemkortet hvis muligt.
2. Placer bunddækslet på håndfladestøtten og tastaturmodulet. 3. Snap bunddækslet på plads – start fra strømadapterporten. FORSIGTIG For at undgå utilsigtet skade på strømadapterporten, må du ikke trykke bunddækslet mod strømadapterporten når du klikker bunddækslet fast på computeren. 4. Genmonter de seks skruer (M2,5x7), der fastgør bunddækslet til håndfladestøtten og tastaturmodulet. 5.
Efterfølgende forudsætninger Genmonter det optiske drev (valgfrit). Batteri Fjernelse af batteriet BEMÆRK Før du arbejder med computerens indvendige dele, skal du læse de sikkerhedsinstruktioner, der fulgte med computeren, og følge trinene i Før du arbejder med computerens indvendige dele. Efter du har arbejdet på computerens indvendige dele, følg vejledningen i Efter du har udført arbejde på computerens indvendige dele.
Forudsætninger 1. Fjern det optiske drev (gælder kun for computere, der sendes med optisk drev). 2. Fjern bunddækslet. Procedure 1. Fjern de fire skruer (M2x3), der fastgør batteriet til håndfladestøtten og tastaturmodulet. 2. Løft batteriet af håndfladestøtten og tastaturmodulet. Sådan genmonteres batteriet BEMÆRK Før du arbejder med computerens indvendige dele, skal du læse de sikkerhedsinstruktioner, der fulgte med computeren, og følge trinene i Før du arbejder med computerens indvendige dele.
• Køb altid originalbatterier fra www.dell.com eller via en autoriseret Dell- partner og forhandler. Procedure 1. Ret batteriets skruehuller på batteriet ind efter håndfladestøtten og tastaturmodulets skruehuller. 2. Genmonter de fire skruer (M2x3), der fastgør batteriet til håndfladestøtten og tastaturmodulet. 3. Tilslut batterikablet til systemkortet. Efterfølgende forudsætninger 1. Genmonter bunddækslet. 2. Genmonter det optiske drev (gælder kun for computere, der sendes med optisk drev).
indvendige dele, følg vejledningen i Efter du har udført arbejde på computerens indvendige dele. For flere oplysninger om bedste praksis for sikkerhed, se hjemmesiden Regulatory Compliance på www.dell.com/regulatory_compliance. Forudsætninger 1. Fjern det optiske drev (gælder kun for computere, der sendes med optisk drev). 2. Fjern bunddækslet. Procedure 1. Find hukommelsesmodulet på din computer. 2.
Efterfølgende forudsætninger 1. Genmonter bunddækslet. 2. Genmonter det optiske drev (gælder kun for computere, der sendes med optisk drev). Trådløs-kort Fjernelse af trådløs-kortet BEMÆRK Før du arbejder med computerens indvendige dele, skal du læse de sikkerhedsinstruktioner, der fulgte med computeren, og følge trinene i Før du arbejder med computerens indvendige dele. Efter du har arbejdet på computerens indvendige dele, følg vejledningen i Efter du har udført arbejde på computerens indvendige dele.
Genmontering af trådløs-kortet BEMÆRK Før du arbejder med computerens indvendige dele, skal du læse de sikkerhedsinstruktioner, der fulgte med computeren, og følge trinene i Før du arbejder med computerens indvendige dele. Efter du har arbejdet på computerens indvendige dele, følg vejledningen i Efter du har udført arbejde på computerens indvendige dele. For flere oplysninger om bedste praksis for sikkerhed, se hjemmesiden Regulatory Compliance på www.dell.com/regulatory_compliance.
Efterfølgende forudsætninger 1. Genmonter bunddækslet. 2. Genmonter det optiske drev (gælder kun for computere, der sendes med optisk drev). Optisk drev-tilslutningskort Sådan fjernes det optiske drevs stikkort BEMÆRK Før du arbejder med computerens indvendige dele, skal du læse de sikkerhedsinstruktioner, der fulgte med computeren, og følge trinene i Før du arbejder med computerens indvendige dele.
Sådan genmonteres det optiske drevs stikkort BEMÆRK Før du arbejder med computerens indvendige dele, skal du læse de sikkerhedsinstruktioner, der fulgte med computeren, og følge trinene i Før du arbejder med computerens indvendige dele. Efter du har arbejdet på computerens indvendige dele, følg vejledningen i Efter du har udført arbejde på computerens indvendige dele. For flere oplysninger om bedste praksis for sikkerhed, se hjemmesiden Regulatory Compliance på www.dell.com/regulatory_compliance.
Møntcellebatteri Sådan fjernes møntcellebatteriet BEMÆRK Før du arbejder med computerens indvendige dele, skal du læse de sikkerhedsinstruktioner, der fulgte med computeren, og følge trinene i Før du arbejder med computerens indvendige dele. Efter du har arbejdet på computerens indvendige dele, følg vejledningen i Efter du har udført arbejde på computerens indvendige dele. For flere oplysninger om bedste praksis for sikkerhed, se hjemmesiden Regulatory Compliance på www.dell.com/regulatory_compliance.
Efterfølgende forudsætninger 1. Genmonter bunddækslet. 2. Genmonter det optiske drev (gælder kun for computere, der sendes med optisk drev). Blæser Fjernelse af blæseren BEMÆRK Før du arbejder med computerens indvendige dele, skal du læse de sikkerhedsinstruktioner, der fulgte med computeren, og følge trinene i Før du arbejder med computerens indvendige dele. Efter du har arbejdet på computerens indvendige dele, følg vejledningen i Efter du har udført arbejde på computerens indvendige dele.
6. Kobl blæserkablet fra systemkortet. 7. Fjern de tre skruer (M2,5x5) der fastgør blæseren til håndfladestøtten og tastaturmodulet. 8. Løft blæseren af håndfladestøtten og tastaturmodulet. Genmontering af blæseren BEMÆRK Før du arbejder med computerens indvendige dele, skal du læse de sikkerhedsinstruktioner, der fulgte med computeren, og følge trinene i Før du arbejder med computerens indvendige dele.
3. Tilslut blæserkablet til systemkortet. 4. Før skærmkablet gennem kabelkanalerne på blæseren. 5. Slut skærmkablet til dets stik på systemkortet, og luk låsen for at fastgøre kablet. BEMÆRK Følgende trin gælder kun for computere, der sendes med optisk drev. 6. Tryk ned på låsen for at slutte kablet for det optiske drevs stikkort til det optiske drevs stikkort. 7. Tryk ned på låsen for at slutte kablet for det optiske drevs stikkort til systemkortet. Efterfølgende forudsætninger 1. Genmonter bunddækslet.
Solid-state-drev/Intel Optane Sådan fjernes solid-state-drevet/Intel Optane Du skal deaktivere Intel Optane-enheden før du fjerner den fra computeren. For mere information om deaktivering af Intel Optaneenheden, gå til Deaktivering af Intel Optane-hukommelsen. BEMÆRK Før du arbejder med computerens indvendige dele, skal du læse de sikkerhedsinstruktioner, der fulgte med computeren, og følge trinene i Før du arbejder med computerens indvendige dele.
Fremgangsmåde for at fjerne M.2 2280 solid-state-drevet 1. Løsn den fastmonterede skrue, der fastgør den termiske M.2 2280-plade til håndfladestøtten og tastaturmodulet. 2. Fjern skruen (M2x3), der fastgør den termiske M.2 2280-plade og solid-state-drevet til håndfladestøtten og tastaturmodulet. 3. Skub og fjern den termiske M.2 2280-plade fra slotten på håndfladestøtten og tastaturmodulet. 4. Løft solid-state-drevet i en vinkel, og fjern det fra M.2-slotten på systemkortet.
BEMÆRK Før du arbejder med computerens indvendige dele, skal du læse de sikkerhedsinstruktioner, der fulgte med computeren, og følge trinene i Før du arbejder med computerens indvendige dele. Efter du har arbejdet på computerens indvendige dele, følg vejledningen i Efter du har udført arbejde på computerens indvendige dele. For flere oplysninger om bedste praksis for sikkerhed, se hjemmesiden Regulatory Compliance på www.dell.com/regulatory_compliance. FORSIGTIG Solid-state-drev er skrøbelige.
Fremgangsmåde for at udskifte M.2 2280 solid-state-drevet 1. Ret indsnittet på solid-state-drevet ind efter tappen på M.2-slotten, og skub solid-state-drevet på plads. 2. Indsæt tappen på den termiske M.2 2280-plade i slotten på håndfladestøtten og tastaturmodulet. 3. Genmonter skruen (M2x3), der fastgør den termiske M.2 2280-plade og solid-state-drevet til håndfladestøtten og tastaturmodulet. 4. Stram den fastmonterede skrue, der fastgør den termiske M.2 2280-plade til håndfladestøtten og tastaturmodulet.
2. Genmonter det optiske drev (gælder kun for computere, der sendes med optisk drev). Harddisk Fjernelse harddisken Hvis din computer benytter en SATA-lagerenhed, som er drevet af Intel Optane hukommelse, skal du deaktivere Intel Optane, før du fjerner SATA-lagerenheden. For mere information om at deaktivere Intel Optane, se Deaktivering af Intel Optane.
5. Fjern de fire skruer (M3x3), der fastgør harddiskbeslaget til harddisken. 6. Løft harddisken af harddiskbeslaget. Sådan genmonteres harddisken Aktivér Intel Optane efter at have udskiftet SATA-storage. For mere information om aktivering af Intel Optane, se Aktivering af Intel Optane. BEMÆRK Før du arbejder med computerens indvendige dele, skal du læse de sikkerhedsinstruktioner, der fulgte med computeren, og følge trinene i Før du arbejder med computerens indvendige dele.
3. Tilslut interposeren til harddiskmodulet. 4. Brug justeringsanordningerne til at placere harddiskmodulet på håndfladestøtten og tastaturmodulet. 5. Genmonter de fire skruer (M2x3), der fastgør harddiskmodulet til håndfladestøtten og tastaturmodulet. 6. Forbind harddiskens kabel med systemkortet, og luk låsen for at fastgøre kablet.
Efterfølgende forudsætninger 1. Genmonter batteriet. 2. Genmonter bunddækslet. 3. Genmonter det optiske drev (gælder kun for computere, der sendes med optisk drev). Berøringsplade Sådan fjernes berøringspladen BEMÆRK Før du arbejder med computerens indvendige dele, skal du læse de sikkerhedsinstruktioner, der fulgte med computeren, og følge trinene i Før du arbejder med computerens indvendige dele.
4. Pil forsigtigt tapen, der fastgør pegefeltet til håndfladestøtten og tastaturmodulet, af. 5. Fjern de fire skruer (M2x2), der fastgør touchpad til håndfladestøtten og tastaturmodulet. 6. Skub og løft pegefeltet væk fra håndfladestøtten og tastaturmodulet. Genmontering af berøringspladen BEMÆRK Før du arbejder med computerens indvendige dele, skal du læse de sikkerhedsinstruktioner, der fulgte med computeren, og følge trinene i Før du arbejder med computerens indvendige dele.
4. Skub harddiskens kabel ind i dets stik på systemkortet, og luk låsen for at fastgøre kablet. 5. Skub touchpad-kablet ind i stikket på systemkortet, og luk låsen for at fastgøre kablet. 6. Skub hvis muligt kablet for tastaturets baggrundsbelysning ind i stikket på systemkortet, og luk låsen for at fastgøre kablet. Efterfølgende forudsætninger 1. Genmonter batteriet. 2. Genmonter bunddækslet. 3. Genmonter det optiske drev (gælder kun for computere, der sendes med optisk drev).
Forudsætninger 1. Fjern det optiske drev (gælder kun for computere, der sendes med optisk drev). 2. Fjern bunddækslet. 3. Fjern solid-state-drevet/Intel Optane. Procedure 1. Frakobl højtalerkablet fra systemkortet. 2. Bemærk fremføringen af højtalerens kabel, og fjern det fra kabelkanalerne på håndfladestøtten og tastaturmodulet. 3. Løft højtalerne og dets kabel væk fra håndfladestøtten og tastaturmodulet.
Efterfølgende forudsætninger 1. Genmonter solid-state-drevet/Intel Optane. 2. Genmonter bunddækslet. 3. Genmonter det optiske drev (gælder kun for computere, der sendes med optisk drev). Varme-sink Fjernelse af kølelegemet BEMÆRK Før du arbejder med computerens indvendige dele, skal du læse de sikkerhedsinstruktioner, der fulgte med computeren, og følge trinene i Før du arbejder med computerens indvendige dele.
Genmontering af kølelegemet BEMÆRK Før du arbejder med computerens indvendige dele, skal du læse de sikkerhedsinstruktioner, der fulgte med computeren, og følge trinene i Før du arbejder med computerens indvendige dele. Efter du har arbejdet på computerens indvendige dele, følg vejledningen i Efter du har udført arbejde på computerens indvendige dele. For flere oplysninger om bedste praksis for sikkerhed, se hjemmesiden Regulatory Compliance på www.dell.com/regulatory_compliance.
Skærmmodul Sådan fjernes skærmmodulet BEMÆRK Før du arbejder med computerens indvendige dele, skal du læse de sikkerhedsinstruktioner, der fulgte med computeren, og følge trinene i Før du arbejder med computerens indvendige dele. Efter du har arbejdet på computerens indvendige dele, følg vejledningen i Efter du har udført arbejde på computerens indvendige dele. For flere oplysninger om bedste praksis for sikkerhed, se hjemmesiden Regulatory Compliance på www.dell.com/regulatory_compliance.
8. Løft håndfladestøtten og tastaturmodulet i en vinkel. 9. Skub og fjern håndfladestøtten og tastaturmodulet fra skærmmodulet. 10. Efter udførelse af alle ovenstående trin, står du tilbage med skærmmodulet.
Sådan genmonteres skærmmodulet BEMÆRK Før du arbejder med computerens indvendige dele, skal du læse de sikkerhedsinstruktioner, der fulgte med computeren, og følge trinene i Før du arbejder med computerens indvendige dele. Efter du har arbejdet på computerens indvendige dele, følg vejledningen i Efter du har udført arbejde på computerens indvendige dele. For flere oplysninger om bedste praksis for sikkerhed, se hjemmesiden Regulatory Compliance på www.dell.com/regulatory_compliance.
4. Genmonter de fem skruer (M2,5x5), der fastgør de venstre og højre hængsler til systemkortet og håndfadestøtten og tastaturmodulet. BEMÆRK Der er en ekstra skrue på det venstre hængsel på computere, der sendes uden optisk drev. 5. Før skærmkablet gennem kabelkanalerne på blæseren og håndfladestøtten og tastaturmodulet. 6. Skub skærmkablet ind i stikket på systemkortet, og luk låsen for at fastgøre kablet. BEMÆRK Følgende trin gælder kun for computere, der sendes med optisk drev. 7.
2. Genmonter bunddækslet. 3. Genmonter det optiske drev (gælder kun for computere, der sendes med optisk drev). Strømadapterport Fjernelse strømadapterporten BEMÆRK Før du arbejder med computerens indvendige dele, skal du læse de sikkerhedsinstruktioner, der fulgte med computeren, og følge trinene i Før du arbejder med computerens indvendige dele. Efter du har arbejdet på computerens indvendige dele, følg vejledningen i Efter du har udført arbejde på computerens indvendige dele.
Procedure 1. Ret skruehullet på strømadapterporten med skruehullet på håndfladestøtten og tastaturmodulet. 2. Genmonter skruen (M2x2), der fastgør strømadapterporten til håndfladestøtten og tastaturmodulet. 3. Før strømadapterportens kabel gennem kabelkanalerne på håndfladestøtten og tastaturmodulet. 4. Tilslut strømadapterportens kabel til systemkortet. 5. Luk det venstre hængsel. 6. Genmonter de fire skruer (M2,5x5), der fastgør det venstre hængsel til systemkortet og håndfladestøttemodulet.
4. Løft I/O-kortet, sammen med dets kabel, væk fra håndfladestøtten og tastaturmodulet. Sådan genmonteres I/O-kortet BEMÆRK Før du arbejder med computerens indvendige dele, skal du læse de sikkerhedsinstruktioner, der fulgte med computeren, og følge trinene i Før du arbejder med computerens indvendige dele. Efter du har arbejdet på computerens indvendige dele, følg vejledningen i Efter du har udført arbejde på computerens indvendige dele.
4. Genmonter det optiske drev (gælder kun for computere, der sendes med optisk drev). Tænd/sluk-knap Sådan fjernes strømknappen BEMÆRK Før du arbejder med computerens indvendige dele, skal du læse de sikkerhedsinstruktioner, der fulgte med computeren, og følge trinene i Før du arbejder med computerens indvendige dele. Efter du har arbejdet på computerens indvendige dele, følg vejledningen i Efter du har udført arbejde på computerens indvendige dele.
Udskiftning af tænd/sluk-knappen BEMÆRK Før du arbejder med computerens indvendige dele, skal du læse de sikkerhedsinstruktioner, der fulgte med computeren, og følge trinene i Før du arbejder med computerens indvendige dele. Efter du har arbejdet på computerens indvendige dele, følg vejledningen i Efter du har udført arbejde på computerens indvendige dele. For flere oplysninger om bedste praksis for sikkerhed, se hjemmesiden Regulatory Compliance på www.dell.com/regulatory_compliance. Procedure 1.
Efterfølgende forudsætninger 1. Genmonter blæseren. 2. Genmonter bunddækslet. 3. Genmonter det optiske drev (gælder kun for computere, der sendes med optisk drev). Systemkort Fjernelse af systemkortet BEMÆRK Før du arbejder med computerens indvendige dele, skal du læse de sikkerhedsinstruktioner, der fulgte med computeren, og følge trinene i Før du arbejder med computerens indvendige dele.
Procedure 1. Frakobl strømadapterportens kabel fra systemkortet. 2. Frakobl højtalerkablet fra systemkortet. 3. Åben låsen og frakobl tastaturet fra systemkortet. 4. Åben låsen og frakobl tastaturets baggrundsbelysningskabel fra systemkortet. 5. Åbn låsen, og frakobl NFC-kablet fra systemkortet. 6. Åben låsen og frakobl harddisken fra systemkortet. 7. Åbn låsen og frakobl I/O-kortets kabel fra systemkortet. 8. Åben låsen og frakobl fingeraftrykslæserens kabel fra systemkortet. 9.
16. Fjern skruen (M2x4), der fastgør systemkortet til håndfladestøtten og tastaturmodulet. 17. Løft systemkortet væk fra håndfladestøtten og tastaturmodulet. Genmontering af systemkortet BEMÆRK Før du arbejder med computerens indvendige dele, skal du læse de sikkerhedsinstruktioner, der fulgte med computeren, og følge trinene i Før du arbejder med computerens indvendige dele.
Procedure 1. Ret skruehullet på systemkortet ind efter skruehullet på håndfladestøtten og tastaturmodulet. 2. Genmonter skruen (M2x4), der fastgør systemkortet til håndfladestøtten og tastaturmodulet. 3. Luk det højre skærmhængsel. 4. Genmonter de tre skruer (M2,5x5), der fastgør det højre hængsel til systemkortet. 5. Skub fingeraftrykslæserens kabel ind i stikket på systemkortet, og luk låsen. 6. Skub I/O-kortets kabel ind i stikket på systemkortet, og luk låsen. 7.
14. Åbn låsen, og slut skærmkablet til systemkortet. 15. Ret kablet for det optiske drevs stikkort ind efter stikkene på systemkortet og håndfladestøtten og tastaturmodulet (valgfrit). 16. Skub kablet for det optiske drevs stikkort ind i stikket på håndfladestøtten og tastaturmodulet (valgfrit). 17. Skub kablet for det optiske drevs stikkort ind i stikket på systemkortet (valgfrit). Efterfølgende forudsætninger 1. Genmonter kølelegemet. 2. Genmonter blæseren. 3. Genmonter solid-state-drevet/Intel Optane.
indvendige dele, følg vejledningen i Efter du har udført arbejde på computerens indvendige dele. For flere oplysninger om bedste praksis for sikkerhed, se hjemmesiden Regulatory Compliance på www.dell.com/regulatory_compliance. BEMÆRK Gælder kun for computere leveret med fingeraftrykslæser. Forudsætninger 1. Fjern det optiske drev (gælder kun for computere, der sendes med optisk drev). 2. Fjern bunddækslet. 3. Fjern batteriet. 4. Fjern solid-state-drevet/Intel Optane 5. Fjern blæseren. 6.
Procedure 1. Brug justeringsanordningerne til at justere og placere tænd/sluk-knappen med fingeraftrykslæser på håndfladestøtten og tastaturmodulet. 2. Genmonter skruen (M2x2), der fastgør tænd/sluk-knappen med fingeraftrykslæseren på håndfladestøtten og tastaturmodulet. 3. Påsæt fingeraftrykslæserens kabel på håndfladestøtten og tastaturmodulet. Efterfølgende forudsætninger 1. Genmonter systemkortet. 2. Genmonter trådløs-kortet. 3. Genmonter kølelegemet. 4. Genmonter blæseren. 5.
6. Fjern solid-state-drevet/Intel Optane 7. Fjern trådløs-kortet. 8. Fjern højtalerne. 9. Fjern harddisken med Intel Optane. 10. Fjern pegefeltet. 11. Fjern strømadapterporten. 12. Fjern skærmmodulet. 13. Fjern I/O-kortet. 14. Fjern systemkortet. BEMÆRK Når du fjerner og genmonterer håndfladestøtten og tastaturmodulet, må du ikke fjerne kølelegemet fra systemkortet. 15. Fjern tænd/sluk-knappen med fingeraftrykslæser (valgfrit).
Efterfølgende forudsætninger 1. Genmonter tænd/sluk-knappen med fingeraftrykslæser (valgfri). 2. Genmonter systemkortet. 3. Genmonter I/O-kortet. 4. Genmonter skærmmodulet. 5. Genmonter strømadapterporten. 6. Genmontering af touchpad. 7. Genmonter harddisken med Intel Optane. 8. Genmonter højttalerne. 9. Genmonter trådløs-kortet. 10. Genmonter solid-state-drevet/Intel Optane. 11. Genmonter blæseren. 12. Genmonter det optiske drevs stikkort (gælder kun for computere, der er sendt med optisk drev). 13.
Procedure BEMÆRK Denne procedure gælder kun for computere, der sendes med skærme uden berøringsteknologi. 1. Lirk forsigtigt, vha. en plastikpen, skærmrammen ud af den øverste venstre, yderste kant på skærmens bagdæksel og antennemodulet. 2. Fjern skærmfacetten af skærmens bagdæksel og antennemodul.
Efterfølgende forudsætninger 1. Genmonter skærmmodulet. 2. Genmonter trådløs-kortet. 3. Genmonter bunddækslet. 4. Genmonter det optiske drev (gælder kun for computere, der sendes med optisk drev). Kamera Sådan fjernes kameraet BEMÆRK Før du arbejder med computerens indvendige dele, skal du læse de sikkerhedsinstruktioner, der fulgte med computeren, og følge trinene i Før du arbejder med computerens indvendige dele.
Genplacering af kameraet BEMÆRK Før du arbejder med computerens indvendige dele, skal du læse de sikkerhedsinstruktioner, der fulgte med computeren, og følge trinene i Før du arbejder med computerens indvendige dele. Efter du har arbejdet på computerens indvendige dele, følg vejledningen i Efter du har udført arbejde på computerens indvendige dele. For flere oplysninger om bedste praksis for sikkerhed, se hjemmesiden Regulatory Compliance på www.dell.com/regulatory_compliance.
Efterfølgende forudsætninger 1. Genmonter skærmfacetten. 2. Genmonter skærmmodulet. 3. Genmonter trådløs-kortet. 4. Genmonter bunddækslet. 5. Genmonter det optiske drev (gælder kun for computere, der sendes med optisk drev). Skærmpanel Sådan fjernes skærmpanelet BEMÆRK Før du arbejder med computerens indvendige dele, skal du læse de sikkerhedsinstruktioner, der fulgte med computeren, og følge trinene i Før du arbejder med computerens indvendige dele.
Genmontering skærmpanelet BEMÆRK Før du arbejder med computerens indvendige dele, skal du læse de sikkerhedsinstruktioner, der fulgte med computeren, og følge trinene i Før du arbejder med computerens indvendige dele. Efter du har arbejdet på computerens indvendige dele, følg vejledningen i Efter du har udført arbejde på computerens indvendige dele. For flere oplysninger om bedste praksis for sikkerhed, se hjemmesiden Regulatory Compliance på www.dell.com/regulatory_compliance.
Efterfølgende forudsætninger 1. Genmonter skærmfacetten. 2. Genmonter skærmmodulet. 3. Genmonter trådløs-kortet. 4. Genmonter bunddækslet. 5. Genmonter det optiske drev (gælder kun for computere, der sendes med optisk drev). Skærmhængsler Sådan fjernes skærmhængslerne BEMÆRK Før du arbejder med computerens indvendige dele, skal du læse de sikkerhedsinstruktioner, der fulgte med computeren, og følge trinene i Før du arbejder med computerens indvendige dele.
Sådan genmonteres skærmhængslerne BEMÆRK Før du arbejder med computerens indvendige dele, skal du læse de sikkerhedsinstruktioner, der fulgte med computeren, og følge trinene i Før du arbejder med computerens indvendige dele. Efter du har arbejdet på computerens indvendige dele, følg vejledningen i Efter du har udført arbejde på computerens indvendige dele. For flere oplysninger om bedste praksis for sikkerhed, se hjemmesiden Regulatory Compliance på www.dell.com/regulatory_compliance. Procedure 1.
3. Genmonter skærmmodulet. 4. Genmonter trådløs-kortet. 5. Genmonter bunddækslet. 6. Genmonter det optiske drev (gælder kun for computere, der sendes med optisk drev). Skærmkabel Sådan fjernes skærmkablet BEMÆRK Før du arbejder med computerens indvendige dele, skal du læse de sikkerhedsinstruktioner, der fulgte med computeren, og følge trinene i Før du arbejder med computerens indvendige dele.
indvendige dele, følg vejledningen i Efter du har udført arbejde på computerens indvendige dele. For flere oplysninger om bedste praksis for sikkerhed, se hjemmesiden Regulatory Compliance på www.dell.com/regulatory_compliance. Procedure BEMÆRK Denne procedure gælder kun for computere, der sendes med skærme uden berøringsteknologi. 1. Før skærmkablet langs kabelkanalerne – start fra bunden af skærmen (i nærheden af hængslerne). 2.
6. Fjern kameraet. 7. Fjern skærmpanelet. 8. Fjern skærmhængslerne. 9. Fjern skærmkablet. Procedure BEMÆRK Denne procedure gælder kun for computere, der sendes med skærme uden berøringsteknologi. Efter at have gennemført de ovenfor beskrevne trin, står vi tilbage med skærmens bagdæksel og antennemodul.
Efterfølgende forudsætninger 1. Genmonter skærmfacetten. 2. Genmonter skærmhængslerne. 3. Genmonter skærmpanelet. 4. Genmonter kameraet. 5. Genmonter skærmfacetten. 6. Genmonter skærmmodulet. 7. Genmonter trådløs-kortet. 8. Genmonter bunddækslet. 9. Genmonter det optiske drev (gælder kun for computere, der sendes med optisk drev).
3 Enhedsdrivere Sådan hentes lyddriveren 1. Tænd computeren 2. Gå til www.dell.com/support. 3. Indtast nummeret fra computerens servicemærke, og klik derefter på Submit (Send). BEMÆRK Hvis du ikke har servicemærket, brug autodetekteringsfunktionen eller gennemse din computermodel manuelt. 4. Klik på Drivers & Downloads (Drivere og downloads). 5. Klik på knappen Detect Drivers (Identificer automatisk drivere). 6.
12. Applikationen installerer alle relevante drivere og opdateringer. BEMÆRK Ikke alle filer kan installeres automatisk. Gennemgå logteksten fra installationen for at se, om manuel installation er påkrævet. 13. Hvis du får brug for en manuel download og installation, skal du klikke på Category (Kategori). 14. Klik på Network (Netværk) i rullelisten. 15. Klik på Download (Hent) for at hente netværksdriveren til computeren. 16.
10. Vælg et sted at gemme filerne. 11. Du skal svare bekræftende, hvis User Account Control (Kontrol af brugerkonti) beder om lov til at foretage ændringer i systemet. 12. Applikationen installerer alle relevante drivere og opdateringer. BEMÆRK Ikke alle filer kan installeres automatisk. Gennemgå logteksten fra installationen for at se, om manuel installation er påkrævet. 13. Hvis du får brug for en manuel download og installation, skal du klikke på Category (Kategori). 14.
9. Klik på Download and Install (Download og installer) for at downloade og installere alle relevante driver-opdateringer til computeren. 10. Vælg et sted at gemme filerne. 11. Du skal svare bekræftende, hvis User Account Control (Kontrol af brugerkonti) beder om lov til at foretage ændringer i systemet. 12. Applikationen installerer alle relevante drivere og opdateringer. BEMÆRK Ikke alle filer kan installeres automatisk. Gennemgå logteksten fra installationen for at se, om manuel installation er påkrævet.
4 Systemopsætning BEMÆRK Afhængigt af computeren og de installerede enheder er det muligvis ikke alle elementer i dette afsnit, der vises. Systemopsætning FORSIGTIG Medmindre du er en erfaren computerbruger, skal du undlade at ændre indstillingerne for dette program. Visse ændringer kan medføre, at computeren ikke fungerer korrekt. BEMÆRK Før du ændrer BIOS opsætningsprogram, anbefales det, at du skriver BIOS-opsætningens skærminformationer ned til fremtidig brug.
Engangsopstartens menu viser de enheder, som du kan starte fra, herunder diagnostiske indstillinger. Opstartsmenuens valgmuligheder er: • • Udtageligt drev (hvis tilgængelig) STXXXX-drev (hvis tilgængeligt) • • • Optisk drev (hvis tilgængelig) SATA-harddisk (hvis tilgængelig) Diagnostics (Diagnosticering) BEMÆRK XXX-betegner SATA-drevnummeret. BEMÆRK Valg af Diagnostics (Diagnosticering) vil vise ePSA diagnostics-skærmen (ePSA-diagnosticering).
5 Fejlfinding Forbedret Pre-Boot System Assessment – ePSAdiagnosticering ePSA-diagnostik (også kendt som systemdiagnostik) udfører et fulstændigt tjek af din hardware. ePSA er indlejret med BIOS og er lanceret af BIOS internt.
Følgende skema viser de forskellige lysmønstre for strøm- og batteristatusindikatoren, og de tilhørende problemer. Tabel 3.
5. Vælg det operativsystem, der er installeret på din computer. 6. Rul ned gennem siden og udvid BIOS. 7. Klik på Download (Hent) for at hente den seneste BIOS-version til computeren. 8. Efter hentning er afsluttet, naviger til mappen hvor du gemte BIOS-opdateringsfilen. 9. Dobbeltklik på BIOS-opdateringsfilens ikon og følg vejledningen på skærmen. Aktiverer Intel Optane-hukommelse 1. På proceslinjen, klik på søgefeltet, og skriv så Intel Rapid Storage Technology. 2. Klik på Intel Rapid Storage Technology.
BEMÆRK Nogle ISP'er (Internet Service Providers) har en kombineret modem/router-enhed. 1. Sluk for computeren. 2. Sluk for modemmet. 3. Sluk for den trådløse router. 4. Vent i 30 sekunder. 5. Tænd den trådløse router. 6. Tænd for modemmet. 7. Tænd computeren. Frigørelse af overskudsstrøm Overskudsstrøm er den ophobede, statiske elektricitet, der er tilbage i computeren, også efter computeren er blevet slukket, og selvom batteriet er fjernet. Følg følgende procedure for få frigjort overskudsstrømmen: 1.
6 Rekvirere hjælp og kontakte Dell Selvhjælpsressourcer Du kan få oplysninger og hjælp til Dell-produkter og servicer ved at bruge disse selvhjælpsressourcer: Tabel 4. Selvhjælpsressourcer Selvhjælpsressourcer Ressourceplacering Information om Dells produkter og services www.dell.com Mit Dell Tips Kontakt supporten I Windows-søgning, skriv Contact Support, og tryk på Enter. Online-hjælp til operativsystem www.dell.com/support/windows www.dell.